OPERATING AND INSTALLATION INSTRUCTIONS FOR
ELECTROLUX FREEZERS
INTRODUCTION
We are pleased that you have chosen this freezer
and hope you will derive much satisfaction from
using it, but first a few well-meant words of advice:
CONTENTS
It is important to read through these instructions
carefully before using the freezer.
CONTROLS……………………………………..4
OPERATING INSTRUCTIONS…………..4
STARTING THE FREEZER……………………4
To ensure good refrigeration and economical
operation, the freezer must be installed and used
as described in these instructions.
REGULATING THE TEMPERATURE………..4
FOOD STORAGE……………………………….4
The freezer is designed for operation in homes,
locations, cottages, holiday homes, chalets or
similar.
DEFROSTING……………………………………5
CLEANING THE FREEZER…………………….5
TRANSIT DAMAGE
TURNING OFF THE FREEZER ……………….5
Inspect the freezer for damage. Transit damage
must be reported to whoever is responsible for
delivery not later than seven days after the freezer
was delivered.
IF THE FREEZER FAILS TO WORK………….5
MAINTENANCE………………………………..6
REGULAR MAINTENANCE……………………6
DATA PLATE
Check the data plate, inside of the freezer, to
ensure that you have received the right model.
The right gas pressure is 28 - 30 mbar
9211605..
Model no.
RC185…
Serial no.
Voltage
Wattage
Fuel
…………………
…………....volts
……...……watts
………………….
SERVICE………………………………………….6
TECHNICAL DATA………………………………6
The data plate contains e.g. the following details:
Product no.
SOME USEFULL HINTS………………………..6
INSTALLATION INSTRUCTIONS…………6
PLACEMENT OF THE FREEZER …………….6
LP GAS CONNECTION ………………………..7
ELECTRICAL CONNECTION …………………7
Since these details will be needed if you have to
contact service personnel, it is a good idea to make
a note of them here.
(3)
OPERATING INSTRUCTIONS
CONTROLS
3.
Check that the electricity supply is
switched off at the main supply.
4.
Set the thermostat knob (A) to the
coldest setting (turn clock wise).
5.
Press the flame failure device button (B)
and turn it to the open position (turn anti
– clock wise).
6.
Keeping the flame failure device button
(B) pressed, press the igniter (D)
repeatedly until the flame ignites. This
will be indicated by the needle of the
flame indicator (C) that will start rising.
7.
Keep the (B) button pressed for a further
10 to 15 seconds and then release it.
All references are to fig. 1.
The controls are located at the bottom of the left
hand front corner of the freezer.
Depending on the model, the freezer can run on
240 V, 230 V, 220 V, 127 V, 110 V, LP Gas or as
indicated on the data plate. The method of
operation is selected by connecting the appropriate
energy source.
The freezer temperature is controlled by a
thermostat (A). The off position of the thermostat
will only switch of the fridge if it is used with
electricity.
The safety valve (B) is used to automatically switch
off the gas supply to the burner when the flame
dies. This valve is also used whenever the gas
operation has to be terminated.
The flame indicator (C) indicates whether the flame
is burning or not.
To terminate gas operation, close the shut off
valve of the gas bottle and close any on board
shut off valves.
Mains electricity Operation
Before switching on the freezer, check that the
voltage stated on the data plate is the same as
the main voltage in use.
The piezo igniter (D) is used to light the gas. When
the button (D) is pressed, sparks are generated at
the burner.
1.
Turn off gas operation when applicable.
2.
Switch on the main supply to the freezer.
STARTING THE FREEZER
3.
Set the thermostat knob (A) to the coldest
setting (turn clock wise).
Caution!
Only use one source of energy at a time
REGULATING THE TEMPERATURE
All references are to fig. 1.
All references are to fig. 1.
LP Gas operation
It will take a few hours for the freezer to reach
normal operating temperature. So we suggest
you start it well in advance of loading it and if
possible store it with precooled foodstuffs.
After initial installation, servicing, or changing gas
cylinders etc., the gas pipes may contain some air,
which should be allowed to escape by briefly
pressing the flame failure device button (B). This
will ensure that the flame lights immediately.
Ensure that the freezer is level before starting up.
Place the spirit level supplied, on the bottom of the
freezer tank to confirm whether it is level. A level
floor will ensure that the fridge is level.
To start gas operation:
1.
Open the shut off valve of the gas bottle
(check that there is enough gas). Open
any on board shut-off valve.
2.
Check for leaks at the connection with a
soap solution.
(4)
Turning the thermostat knob (A) in a clockwise
direction will result in a colder temperature as
desired.
FOOD STORAGE
Always keep food in closed containers. Never put
hot food in the freezer, allow it to cool first.
Never keep items in the freezer, which might
give off flammable gasses.
The freezer is intended for the storage of frozen
food and for making ice.
Most kinds of food can be stored in the freezer
for about a month. This period of time may vary,
and it is important to follow the instructions on the
individual packets.
should only be cleaned with soap and water and
then thoroughly dried.
Never put bottles or cans of fizzy drinks in the
freezer during normal operation as they might burst
when freezing.
TURNING OFF THE FREEZER
When using this freezer as a bottle cooler the
thermostat setting must be adjusted to prevent
bottles from freezing.
If the freezer is not to be used for some time:
1.
Close the shut off valve of the gas bottle and
close any on board shut off valves.
2.
Switch off the main electricity supply to the
freezer
3.
Empty the freezer. Defrost and clean it as
described earlier.
DEFROSTING
Frost will gradually accumulate on the freezer and
evaporator surfaces. It must not be allowed to grow
too thick as it acts as an insulator and adversely
affects freezer performance.
Check the formation of frost regularly every week
and when it gets about 5 mm thick, defrost the
freezer.
To defrost the freezer, turn it off and remove all
food items, leave the freezer lid open. Warning:
normally the temperature of items of frozen foods
would rise unduly during defrosting and they should
be consumed within 24 h or discarded.
IF THE ‘FREEZER FAILS TO WORK
Check the following points before calling a
service technician:
1. That the “STARTING THE
instructions have been followed.
FREEZER”
2. The freezer is level.
Do not try to accelerate defrosting by using any
kind of heating appliance, as this might damage the
plastic surfaces of the freezer. Neither should any
sharp objects be used to scrape off the ice.
3. If it is possible to start the freezer on any of
the connected sources of energy.
4. If the freezer fails to work on gas, check:
Defrost water should be mopped up with a cloth.
1
1
1
When the ice has melted, wipe the freezer dry and
restart it. Place the food items back inside but wait
until the freezer is cold before making ice cubes.
Some units are fitted with a drainpipe on the right
hand back corner of the inner tank. Remove the
cap and water will drain to the outside.
5. If the freezer fails to work on the mains
electricity supply, check:
1
CLEANING THE FREEZER
Clean the inside of the freezer regularly to keep it
fresh and hygienic.
Soak a cloth in a solution consisting of a teaspoon
of bicarbonate of soda to half a litre of warm water.
Wring out the cloth and use it to clean the interior of
the freezer and fittings.
Never use detergents, scouring powder, strongly
scented products or wax polish to clean the interior
of the freezer as they may damage the surfaces
and leave strong odour.
The exterior of the freezer should be wiped clean
now and again, using a damp cloth and a small
quantity of detergent. But not the lid gasket, which
(5)
That the gas bottle is not empty.
That all LP gas valves are open.
That the thermostat is not in the off
position
1
That the appropriate of the mains
electricity supply voltage is connected to
the freezer. See data plate for correct
voltage.
That the thermostat is not in the off
position
If the freezer is not cooling sufficiently, the
reason may be:
1.
Inadequate ventilation of the cooling unit;
see
the
paragraph
PLACING
THE
FREEZER.
2.
The evaporator is frosted up.
3.
Incorrect thermostat setting.
4.
Incorrect gas pressure – please check the
pressure regulator on the gas container.
5.
Incorrect electrical source – confirm that the
main electrical supply is the same as that
specified on the data label.
6.
The ambient temperature is too high.
7.
Too much food is loaded at one time.
8.
More than one source of energy is used at the
same time.
If the freezer still does not work properly, call a
service technician.
The sealed cooling system must not be opened,
since it contains corroding chemicals under
high pressure.
Capacity
Gross
185 litres
Weight (without packing)
50 kg
Electrical data
Input all Voltages
300 Watt
LP Gas data
Input, max.
Rating
Pressure
Category
Jet size
Cooling medium
MAINTENANCE
32 g/hour
440 Watt
28 – 30 mbar
I3 (BP 30) Propane/Butabe (50/50)
&
I3+ (28-30/37)
“4”
Ammonia
Always turn to a qualified Electrolux Service agent
who is familiar with LP gas systems and freezers.
We recommend that a service technician check the
freezer once a year.
INSTALLATION INSTRUCTIONS
1
Check all connections in the LP gas
system for gas leaks. Connections can be
tested for leaks using a soap solution. Do
not use a naked flame!
This appliance shall be installed
accordance with the regulations in force
1
Check that the burner is clean and free
from combustible material.
PLACEMENT OF THE FREEZER
The room should have a capacity (length x width
3
x height) of at least 20m and must be adequately
ventilated and be in accordance with all relevant
national and local regulations.
SOME USEFUL HINTS
Make sure that:
1
Defrosting is carried out periodically.
1
The freezer is clean and dry with the lid
left open when it is not to be used for
some time.
1
Liquids or items with a strong odour are
well packed
1
There is free air circulation over the
cooling unit at the rear of the freezer.
SERVICE
Service and spare parts are obtained from your
dealer or Electrolux – consult the telephone
directory.
TECHNICAL DATA
Overall dimensions, freezer
Height
Width
Depth (incl. cooling unit)
in
The freezer must be used in a well-ventilated
area, above ground and protected from rain.
The freezer may never be used in a
basement
It is important that the freezer is not subjected to
radiated heat from a stove, the sun etc. Do not
place in front of a window.
For best results at high ambient temperatures
there must be a free air circulation over the
cooling unit at the rear of the freezer but not a
draught. The freezer is designed for a
freestanding installation and the clearance to the
rear wall should be at least 100mm and to
possible sidewalls should be at least 80mm. The
cooling fins at the rear of the cabinet must not be
covered. (Fig. 2)
The freezer should be placed close enough to a
electrical supply so that the plug is assessable to
be disconnected.
850 mm
920 mm
750 mm
(6)
The freezer should be adjusted to be level from left
to right as well as from the front to the back. Place
the spirit level supplied, on the bottom of the tank of
the freezer to confirm whether it is level. A level
floor will ensure that the fridge is level.
which is marked with the letter E or by the
Symbol
, or coloured Green or Green
and Yellow,
-
the wire which is coloured Blue must be
connected to the terminal which is marked
with the letter N or coloured Black,
LP GAS CONNECTION
-
The freezer is designed for operation on LP gas,
the pressure of which must be as indicated in the
table below. Check that this is stated on the Data
plate.
the wire which is coloured Brown must be
connected to the terminal which is marked
with the letter L or coloured Red.
WARNING- THIS
EARTHED
The freezer should always be kept away from
inflammable materials.
Category
I3 (BP 30)
I3+ (28-30/37)
Type of gas
Butane/Propane
(50/50)
Butane
Propane
MUST
BE
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or a similarly qualified person, in order
to avoid a hazard.
Pressure
28 – 30 mbar
29 mbar
37 mbar
The LP Gas inlet connection of the freezer consists
of an 8mm gas supply pipe to take a compression
fitting. This is located at the back of the freezer. The
freezer should be installed in accordance with the
regulations in force
The freezer is not designed for operation on
town gas or natural gas.
CAUTION! CHECK THAT THE GAS SUPPLIED
TO THE FREEZER IS AT THE CORRECT
PRESSURE. SEE THE REGULATOR ON THE LP
GAS CONTAINER.
The gas installation should only be carried out by a
person experienced in gas fittings
On completion of installation, the system must
be pressure tested by a qualified person.
ELECTRICAL CONNECTION
The electrical installation must be carried out in a
proper and durable manner, taking into account all
relevant regulations and codes of practice.
For connection to a mains electrical supply, the
freezer has a 3–core mains lead which is intended
for connection to a properly earthed plug and
socket outlet.
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follow:
-
APPLIANCE
the wire which is coloured Green and Yellow
must be connected to the terminal in the plug
(7)
IMPORTANT
The wires in this mains lead are coloured in
accordance with the following code:
-
green/yellow
blue
brown
earth
neutral
live
Electrical leads must be routed and secured
so that they cannot come into contact with
hot or sharp parts of the freezer.
">
