55332-gb.fm5 Page 21 Monday, March 26, 2001 3:43 PM
TABLE OF CONTENTS
GB
INSTALLATION
PAGE
22
ELECTRICAL CONNECTION
PAGE
23
BEFORE USING THE OVEN
PAGE
24
PROTECTING THE ENVIRONMENT
PAGE
24
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
PAGE
24
OVEN ACCESSORIES
PAGE
25
COOKING CHART
PAGE
26
CLEANING THE OVEN AND ITS ACCESSORIES
PAGE
27
TROUBLESHOOTING GUIDE
PAGE
28
AFTER-SALES SERVICE
PAGE
29
DECLARATION OF CONFORMITY CE
PAGE
29
21
55332-gb.fm5 Page 22 Monday, March 26, 2001 3:43 PM
INSTALLATION
Technical information for the installer
•
•
•
•
•
•
•
•
•
•
•
•
22
After removing the oven from its packaging,
before making the connections place it on the
polystyrene foam base to protect it from
damage.
Do not attempt to lift the oven by the handle.
Lift at the sides as shown in the figure
(see arrow).
Check that the appliance has not been
damaged in transit.
Oven dimensions and kitchen unit
dimensions are shown in the opposite figure.
Kitchen units in contact with the oven must
be heat resistant (80° C min).
Connect the earth wire (A) of the cooktop to
the oven (B) as illustrated.
Connect clamps (C) of the cooktop to the
oven junction block (D) situated in the upper
section, following the colour code indicated
on the plate.
Install the oven in the housing, lifting it at the
sides, taking care not to trap the wires of the
electrical supply cable.
For correct ventilation, follow the ventilation
opening directions shown in the figure
(at least 500 x 80 mm or an equivalent area).
Also provide for at least 5 mm clearance
between the top of the oven and the lower
edge of the worktop.This space must not be
obstructed by cross rails or other structural
elements.
During oven installation, care must be taken
to ensure that the sides are not touching the
front edges of the housing or adjacent
drawers and doors (see picture).
Carry out the electrical connections between
cooktop and oven (see chapter Electrical
Connection).
Secure the oven to the kitchen unit with
screws (A) as shown.
No Contacts
55332-gb.fm5 Page 23 Monday, March 26, 2001 3:43 PM
ELECTRICAL CONNECTION
•
•
•
Warning: Do not connect to the power
supply before you have finished
connecting the oven and cooktop.
Make sure the oven is installed and
connected to the electricity supply by a
qualified technician in accordance with
the manufacturer’s instructions and in
compliance with local regulations.
The installer is responsible for the correct
electrical connection of the oven and the
observance of the relative safety
prescriptions.
•
•
•
•
The oven must be connected to the
electricity supply by means of an all-pole
disconnect switch with minimum contact
gap of 3 mm.
The appliances must be earthed by law.
Do not use multiple plug adapters or
extension leads.
After the oven has been installed, the
electrical components must be
inaccessible.
Interconnecting cooktop and oven
•
•
Make sure that the voltage shown on the
rating plate is the same as the power supply
voltage in your home. The rating plate is on
the front edge of the oven cavity (visible with
oven door open).
Use a type H05RR-F power cord (minimum
length 800 mm):
Conductors X
number
Connection
1N+
~
H05 RR-F 3x4 mm²
2N+
~
H05 RR-F 4x2.5 mm²
3+
3N+
~
~
H05 RR-F 4x2.5 mm²
H05 RR-F 5x1.5 mm²
23
55332-gb.fm5 Page 24 Monday, March 26, 2001 3:43 PM
BEFORE USING THE OVEN
•
•
To make the most of your new oven, read the
users instructions carefully and keep them on
hand for consultation in the future.
Remove the cardboard protections and the
protective plastic film.
•
Remove the accessories from the oven and
heat it 200° C for about an hour to eliminate
the smell of protective grease and insulating
materials. Keep the window open during this
procedure.
PROTECTING THE ENVIRONMENT
1. Packing
• The packaging material can be 100%
recycled, as confirmed by the recycling
symbol ( ).
2. Products
• The appliances are built from recyclable
materials. If you decide to scrap the
appliances act responsibly and observe local
waste disposal by laws. Cut off the power
cords so that the appliances cannot be
connected to the mains.
.
PRECAUTIONS AND GENERAL RECOMMENDATIONS
•
•
•
•
•
•
•
•
24
Before any maintenance on the oven
disconnect it from the electrical power
supply.
Keep children away from the oven when it is in
use and when its has just been switched off.
The oven must be repaired or adjusted
exclusively by a qualified technician.
Make sure that the electrical wires of other
electrical appliances near the oven do not
come into contact with hot parts and do not
become entrapped in the oven door.
Use oven gloves to remove baking trays and
accessories when the oven is hot.
Do not cover the bottom of the oven with
aluminium foil.
Do not place inflammable material in the
oven - risk of fire if the oven is inadvertently
switches on.
During the cooking process, water
evaporates from food. All ovens require this
steam and other fumes to be vented from the
oven cavity. For reasons of safety and
aesthetics, we have determined that an
opening at the bottom of the door is the
optimum solution. Consequently, vapour
may be seen to be coming from this area on
occasions (see picture). This is a normal
occurrence and the bottom trim can be
cleaned after removal of the oven door as
described later in this chapter “Cleaning the
oven and its Accessories”.
•
Heavy weights must not be placed on the
open door as this may result in damage to the
cavity and hinges. Max weight: 7 kg (15 lbs).
Fum
es
E xh
a us
t
55332-gb.fm5 Page 25 Monday, March 26, 2001 3:43 PM
OVEN ACCESSORIES
•
Accessories supplied depend on the model
(refer to the “Product Description Sheet”
supplied separately).
Drip tray
The drip tray is designed to collect fat and food
particles when it is positioned under the grid; it
can also be used as a griddle to cook meat,
chicken and fish, with or without vegetables.
When using the drip tray under the grid, pour in
a little water to avoid fat spatters and smoke.
Baking tray
For cooking biscuits, meringues and pizzas.
Grid
The grid can be used to grill food or as a support
for baking trays, cake tins and other cooking
receptacles. It can be placed on any of the
runners in the oven.
Catalytic panels (depending on model)
The catalytic panels have a microporous coating
that absorbs fat spatters. We recommend an
automatic cleaning cycle after cooking particular
fatty food.
1. To clean the oven heat it to 200° C when
empty and leave it switched on for about an
hour.
2. At the end of the cycle and when the oven is
cool, use a moist sponge to remove food
residues if necessary.
Do not use detergent or cleaners - risk of
damaging the catalytic enamel coating.
Spit (depending on model)
Use the spit as indicated in the relevant chapter
in the “Product Description Sheet” supplied
separately.
25
55332-gb.fm5 Page 26 Monday, March 26, 2001 3:43 PM
COOKING CHART
N.B: The oven functions depend on the model: refer to the separate Product Description
Sheet.
Food
Static function
Temp.
°C
Runner Cooking
from
Time
bottom (Mins.)
Fan function
Temp.
°C
Pastries
Runner Cooking
Temp.
from
Time
°C
bottom (Mins.)
Runner Cooking
from
Time
bottom (Mins.)
Meat
Lamb (1,5 Kg)
Kid (1,5 Kg)
Mutton (1,5 Kg)
Veal (1,5 Kg)
Beef (1 Kg)
Pork (1 Kg)
Rabbit (1,5 Kg)
Chicken (1 Kg)
Turkey (3 Kg)
Goose (2 Kg)
Duck (1,5 Kg)
220
220
220
220
220
220
220
220
220
220
220
2
2
2
2
2
2
2
2
2
2
2
80-90
80-90
80-90
80-90
70-80
70-80
80-90
65-75
140-160
100-120
80-90
200
200
200
200
200
200
200
200
200
200
200
2
2
2
2
2
2
3
2
2
2
2
75-85
75-85
75-85
75-85
65-75
65-75
75-85
60-70
130-150
90-100
75-85
180
180
180
175
175
175
180
200
180
200
200
2
2
2
2
2
2
2
2
2
2
2
70-80
70-80
70-80
70-80
60-70
60-70
70-80
55-65
120-140
85-95
70-80
200
200
200
200
200
2
2
2
2
2
45-55
45-55
45-55
45-55
45-55
180
180
180
180
180
2
2
2
2
3
40-50
40-50
40-50
40-50
40-50
170
170
170
170
170
2
2
2
2
2
40-50
40-50
40-50
40-50
40-50
200
200
200
200
200
2
2
2
2
2
45-55
40-50
40-50
40-50
40-50
180
180
180
180
180
3
3
3
3
3
35-45
35-45
35-45
35-45
30-35
170
170
170
170
170
2
2
2
2
2
30-40
30-40
30-40
30-40
30-40
200
200
200
200
2
2
2
2
40-50
60-70
60-70
70-80
180
180
200
200
2
3
3
3
40-50
55-65
55-65
65-75
170
180
190
190
2
2
2
2
45-55
50-60
55-65
60-70
160
2
35-45
150
3
30-40
150
2
40-50
180
2
40-50
160
3
45-55
160
2
45-55
180
200
180
180
180
250
250
220
225
200
2
2
2
2
2
2
2
2
2
2
40-50
45-55
30-40
30-35
50-60
50-60
20-30
35-45
15-20
40-50
160
190
150
170
160
220
250
200
200
180
3
3
1-3
2-3
3
2
1-3
3
1-3
2
45-55
45-50
25-35
30-40
45-55
50-60
30-40
35-45
15-20
45-55
170
180
140
170
170
220
250
190
190
180
2
2
2-4
2-4
2
2
2
2
2-4
2
40-50
45-55
20-30
30-35
50-60
50-60
20-30
35-45
15-20
40-50
Fish (~ 1 kg)
Gilt head
Bass
Salmon
Tuna
Trout
Fish steaks (kg. 1)
Swordfish
Tuna
Salmon
Cod
Fillet
Vegetables
Stuffed peppers
Stuffed tomatoes
Baked potatoes
Au gratin
Desserts etc.
Cakes
Cake with filling
(fruit - cheese)
Tarts
Apple strudel
Biscuits
Choux pastry
Pies
Bread
Pizza
Lasagne
Vol-au-vents
Soufflès
N.B.: Cooking times and temperatures are purely guidelines. Oven functions depend on the
model. Refer to the separate Product Description Sheet.
26
55332-gb.fm5 Page 27 Monday, March 26, 2001 3:43 PM
COOKING CHART
Food
Grill
Sirloin steak
Cutlets
Sausages
Pork chops
Fish
Chicken drumstick
Kebabs
Spare ribs
Chicken halves
Whole chicken
Roast (pork, beef, veal) (~ 1kg)
Duck
Leg of lamb
Roast Beef
Runner
from
bottom
4
4
4
4
4
4
4
4
3
-
Temp.
°C
250
250
250
250
225
225
225
225
225
-
Grill + Fan
Cooking
Time
(Mins.)
20-30
15-20
20-30
20-30
15-25
15-25
20-30
30-40
35-45
-
Temp.
°C
225
225
225
225
220
200
200
200
200
200
175
180
200
200
Runner
from
bottom
3
3
3
3
3
3
3
3
3
3
2
2
2
2
Cooking
Time
(Mins.)
30-40
20-40
30-40
30-40
20-30
25-35
35-45
40-50
40-50
60-70
90-100
90-120
80-90
50-60
N.B.: Cooking times and temperatures are purely guidelines. Oven functions depend on the
model. Refer to the separate “Product Description Sheet”.
CLEANING THE OVEN AND ITS ACCESSORIES
•
•
•
•
•
•
•
When you finish cooking, wait for the oven to
cool and then clean it to prevent the build-up
of baked-on residues.
If the food residues are baked on, use a
specific oven cleaner and follow the
manufacturer’s instructions on the pack.
Clean the exterior of the oven with a sponge
and warm water.
Do not use abrasive cleaners or pan
scourers.
Use a liquid detergent to clean the oven door
window.
Wash the accessories in a dishwasher or in
the sink, using an oven cleaner.
After the oven has been in prolonged use and
when cooking on different levels (especially
food with high water contents such as pizzas,
stuffed vegetables, etc.) condensate may
form on the inside of the door seal. When the
oven is cool, dry any condensate with a cloth
or sponge.
27
55332-gb.fm5 Page 28 Monday, March 26, 2001 3:43 PM
CLEANING THE OVEN AND ITS ACCESSORIES
Removing the oven door (for cleaning)
.
1. Open the oven door.
2. Press hinge catches (A) forwards.
3. Lift the catches until they engage and then
remove the door.
4. Warning: while you are cleaning the oven,
ensure you do not disengage the hinge
retainer catches.
5. Refit the oven door by following the above
steps in reverse order.
Dropping the grill element to clean the oven
roof (depending on model)
• Do not attempt to clean the oven until it is
cool.
1. To clean the oven roof, pull out the grill
element and lower it as far as it will go.
2. Clean the oven roof and then return the grill
element to its original position.
Changing the oven lamp
1. Disconnect the oven from electrical supply.
2. Unscrew the lamp cover.
3. Change the lamp (see N.B.).
4. Refit the lamp cover.
5. Reconnect the electrical supply.
Changing the lateral lamp (depending on
model)
Disconnect the oven from electrical supply.
Remove the left hand side grid.
Use a screwdriver to prize off the lamp cover.
Change the lamp (see N.B.).
Reposition the lamp cover and press it
against the oven wall until it clicks into place.
6. Refit the side grid.
7. Reconnect the power supply.
N.B:
Use exclusively 25 W 230 V lamps, type E-14,
T300° C, available from After-sales Service.
1.
2.
3.
4.
5.
TROUBLESHOOTING GUIDE
Oven not working
• Switch the oven off and then on again to see
if the problem persists.
• Check for the presence of mains electrical
power.
• Oven selector on position “0” ?
• Check whether you have made the
temperature setting and the function setting.
28
•
•
If the electronic programmer (depending on
model) display presents the message “OFF”,
press any key to reset the oven and then set
the clock.
Ensure that the mechanical programmer
(depending on model) is set to
.
55332-gb.fm5 Page 29 Monday, March 26, 2001 3:43 PM
AFTER-SALES SERVICE
Before contacting After-sales Service:
1. Try to solve the problem (see Troubleshooting
Guide).
2. Turn off the appliance and restart it to see if the
fault is repeated.
If after the above checks the fault still occurs, get
in touch with the nearest After-sales Service.
Please give:
• a short description of the fault,
• the exact type and model,
• the service number (number after the word Service
on the rating plate) is located on the right hand
edge of the oven cavity (visible when the oven
door is open). The service numbers are also
indicated on the guarantee booklet,
• Your complete address and phone number.
If any repairs are required, please contact an
authorised After-sales Service as indicated in the
warranty.
In the unlikely event that an operation or repair is
carried out by an unauthorised technician, always
request a certification of the job carried out and insist
on the use of original spare parts.
Failure to comply with these instructions may
compromise the safety and quality of the product.
DECLARATION OF CONFORMITY CE
•
•
•
•
•
•
These appliances are designed to come into
contact with foodstuffs and they are constructed in
compliance with Directive 89/109/EEC.
The appliances are designed solely for use as
cooking appliances. Any other use of the
appliances (e.g. for room heating) is considered as
improper use and potentially dangerous.
The appliances are designed, built and sold in
compliance with:
The safety requirements of “Low Voltage”
Directive 73/23/EEC.
The protection requirements of EMC
Directive 89/336/EEC.
The requirement of Directive 93/68/EEC.
29
">
