18010gb.fm5 Page 11 Tuesday, September 18, 2001 5:13 PM
TABLE OF CONTENTS
GB
DESCRIPTION OF THE DRYER
PAGE
12
FILTER
PAGE
12
BEFORE USING THE DRYER
PAGE
12
PRECAUTIONS
PAGE
12
PREPARING THE LAUNDRY
PAGE
13
SELECTING DRYING TIME OR PROGRAMME
AND OPTIONS
PAGE
14
STARTING AND COMPLETING THE PROGRAMME
PAGE
15
INSTALLATION
PAGE
16
ELECTRICAL CONNECTION
PAGE
16
VENT CONNECTION
PAGE
18
DOOR REVERSIBILITY
PAGE
18
MAINTENANCE
PAGE
19
TROUBLE SHOOTING GUIDE
PAGE
19
AFTER-SALES SERVICE
PAGE
19
To get full satisfaction from your dryer, please read carefully your instruction manual.
11
18010gb.fm5 Page 12 Tuesday, September 18, 2001 5:13 PM
DESCRIPTION OF THE DRYER
1. Work-top
2. Contact pin
3. Door (Door opening can be reversed).
See “Door reversibility” section.
To open the door: pull the handle out.
To close the door: push the door gently until
it closes.
4. Lint filter
FILTER
Clean the lint filter at the end of each
drying cycle.
1. Pull the filter upwards.
2. Brush lint using a soft brush or your
fingertips.
Filter Indicator light (if available)
It warns that the filter is dirty and needs to be
cleaned.
If the laundry is insufficiently dry, check that the
filter is not clogged.
3. Push it back into housing until it clicks.
BEFORE USING THE DRYER
•
•
•
After unpacking please make sure that the
dryer is undamaged. In case of doubt do not
use the dryer but call a qualified technician or
your retailer.
Packaging material (plastic, etc.) must be
kept out of the reach of children as it
constitutes a potential risk.
This dryer was designed for domestic use
and must be used exclusively for drying
laundry.
Environmental hints
1. Packaging material
The packaging material can be 100%
recycled, as confirmed by the recycling
symbol ( ).
2. Dryer
The dryer is built from recyclable materials.
If you decide to scrap the dryer act
responsibly and observe local waste
disposal by laws. Cut off the power cord so
that the dryer cannot be connected to the
mains.
PRECAUTIONS
Child safety
•
After use, set the programme selector to
position “0”. This prevents children from
switching on the dryer accidentally.
For domestic use only.
12
This dryer conforms to EEC directive
93/68.
18010gb.fm5 Page 13 Tuesday, September 18, 2001 5:13 PM
PREPARING THE LAUNDRY
Laundry preparation
Check that all fastenings are closed and that pockets
are empty. Turn the articles inside out. Place laundry
loosely in the drum to make sure that they don’t get
tangled.
Max. drying weight
•
•
•
•
Cottons
Cottons
with Rapid option
Synthetics
Delicates
5,0 kg
3,5 kg (electronic dryer)
2,5 kg
1,5 kg
The given weights correspond to a standard laundry
load.
Sort laundry as follows
A) By care symbols
On the collar or inside seam:
Suitable for tumble drying
Tumble drying at low temperature only
Do not tumble dry
B) By amount and weight
Whenever the load is bigger than the dryer
capacity, separate laundry according to weight
(e.g. towels from thin underwear).
C) By type of fabrics
Cottons/linen: Towels, cotton jersey, bed and
table linen made of cotton or linen.
Synthetics: Blouses, shirts, overalls, etc. made of
polyester or polyamide, as well as for cotton/
synthetic mixes.
D) By drying level
• Sort into: iron dry, cupboard dry, etc.
Do not tumble dry:
Woollens, silk, delicate fabrics, nylon stockings,
delicate embroidery, fabrics with metallic decorations,
bulky items such as sleeping bags, etc.
Attention: Do not dry articles which have been
treated with a dry cleaning fluid or rubber articles
(danger of fire or explosion). Do not dry laundry
dirty with vegetable oils.
13
18010gb.fm5 Page 14 Tuesday, September 18, 2001 5:13 PM
SELECTING DRYING TIME OR PROGRAMME AND OPTIONS
Electronic dryer
1. Select the programme and the options as
indicated in the table (see Programme
Table).
2. Options (If available)
To select an option, press the corresponding
button before pressing the Start button.
The indicator above the button lights up to
confirm that a selection has been made. An
alarm sounds to indicate that an incorrect
selection has been made (incompatible
options). Press the button again to cancel
the option.
Delayed Start
Delays dryer starting. Every time the
corresponding button is pressed the
start time is delayed from 2 to 8 hours
in 2 hourly steps. After the desired time
is selected, press the Start button.
When the light flashes the delayed start
is running. The delay can be changed
or cancelled by selecting “0” with the
programme selector knob.
Opening the door stops the countdown. Close the door and press the
Start button again to continue the
count-down.
Gentle
Reduces the drying temperature.
Suitable for delicate articles.
Rapid (Cottons only) Max. 3,5 kg.
Shortens the drying time (e.g. cloths or
other laundry of equal size). Do not use
the option for large items (e.g. sheets or
similar).
14
Buzzer
Pressing the button initiates a buzzer
sound to signal at regular intervals, at
the end of the drying cycle.
3. Additional Programmes
Airing
The laundry will be aired during 30
minutes without heating.
Time programme (20 to 60 minutes)
To gently finish dry or dry single items.
Suitable for all fabrics.
18010gb.fm5 Page 15 Tuesday, September 18, 2001 5:13 PM
SELECTING DRYING TIME OR PROGRAMME AND OPTIONS
Time-steered dryer
1. Select the drying time and the options
according to the table (see Programme
Table).
2. Options (if available)
To select an option, press the corresponding
button. Press the button again to cancel the
option.
Delayed start
Delays dryer starting. The start delay
selector should be turned clockwise to
the required time delay and the Start
button pressed. It is possible to select a
delay from 1 to 8 hours. The time delay
can be changed at any time by simply
turning the start delay selector.
The remaining time to the programme
chart is shown on the selector.
Openning the door stops the countdown. Close the door and press the
Start button again to continue the
count-down. To cancel the count-down
turn start delay selector to “0”.
Gentle
Reduces the drying temperature.
Suitable for delicate articles.
Buzzer
Pressing the button initiates a buzzer
sound to signal at regular intervals, at
the end of the drying cycle.
3. Additional Programme
Airing
The laundry will be aired during 20
minutes without heating.
STARTING AND COMPLETING THE PROGRAMME
1. Having selected the desired drying time or
programme and options, press the Start
button.
2. If selected a buzzer sounds to signal the end
of the drying cycle. It will sound at regular
intervals for some time.
3. If you do not unload the laundry at the end of
the drying cycle, an automatic anti-crease
cycle will operate for maximum 20 minutes
(Time-steered dryer) or 70 minutes
(Electronic dryer): the drum rotates at regular
intervals preventing the laundry from
creasing.
Interruption of the drying cycle
To interrupt the dryer during the drying cycle, set
the programme selector knob to position ( )
Airing and press the Start button again for the
Electronic dryer.
Wait at least 5 minutes before opening the door
to allow the dryer to cool down.
For your safety the programme stops
automatically if you open the door. To restart
close the door and press the Start button again.
4. On completion of the programme, set the
programme selector knob to position “0”. The
“Machine On” light goes off.
5. Clean the lint filter at the end of each
drying cycle.
6. If you change the programme (Electronic
dryer) during the drying cycle the dryer stops.
To operate the new programme press the
Start button again.
15
18010gb.fm5 Page 16 Tuesday, September 18, 2001 5:13 PM
INSTALLATION
•
•
•
•
•
Install your dryer in a room which is not subject to
extreme conditions.
When operating the tumble dryer, the room has to
be adequately ventilated to avoid possible back
flow of gases into the room from other appliances
burning fuels, such as coal, gaz and including
open fires.
Remove the protective foil from the control panel.
Level the dryer adjusting the 2 feet at the front.
Take care not to trap the mains cable between the
dryer and the wall.
Stacking kit
Your dryer can be stacked on top of your washing
machine, using the stacking kit AMH 542, which is
available from your dealer.
Minimum housing dimensions:
Width: 600 mm
Height: 850 mm
Depth: 560 mm
ELECTRICAL CONNECTION
•
•
•
•
•
•
•
16
The electrical connection has to be carried out
in compliance with local regulations.
Information on the permissible operating
voltage, the power consumption and the
required fuse protection is given on the rating
plate on the back of the dryer.
The earthing of this dryer is compulsory by
law.
Do not use extension cords or multiple
adapters.
Before any maintenance on the dryer,
disconnect it from the mains supply.
Do not operate the dryer if it has been damaged
during transport. Contact a qualified service
technician.
In case of replacement of mains cable contact
a qualified service technician.
18010gb.fm5 Page 17 Tuesday, September 18, 2001 5:13 PM
ELECTRICAL CONNECTION
1) ELECTRICAL CONNECTIONS
“Warning - this appliance must be
earthed”
This appliance is normally supplied with a
mains lead having a plug fitted in the factory
which has been checked for correct earth
continuity.
If the fitted plug is not suitable for your socket
outlet, or if the machine’s mains lead is not
fitted with a plug, you should fit a suitable new,
good quality plug by following the instructions in
(2) below.
Any unsuitable plug should be cut off and
disposed of in order to avoid a possible shock
hazard should it be inserted into a socket.
2.2 Non-polarized plugs (e.g. 2 pin with side
earth contact)
The wire which is coloured GREEN AND
YELLOW must be connected to the earth
contact. The other two wires should be
connected to the two pins, irrespective of
colour.
3) FUSE REPLACEMENT
If the mains lead of this appliance is fitted with
a BS 1363A 13 amp fused plug, replace the
fuse only with an A.S.T.A. approved type
conforming to BS 1362 and proceed as follows:
2) CONNECTION TO A REWIRABLE
PLUG - to be carried out only by a
qualified electrician
The wires in the mains lead are coloured in
accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN AND YELLOW - “EARTH” (“E”)
To fit a new plug, proceed as follows:
2.1 Polarized Plugs (e.g. 3 pin, 13 amp plug
conforming to BS 1363A)
a. The GREEN AND YELLOW wire must be
connected to the terminal in the plug which
is marked with the letter “E” or by the Earth
symbol
or coloured yellow or green and
yellow.
b. The BLUE wire must be connected to the
terminal which is marked with the letter “N”
or coloured black.
c. The BROWN wire must be connected to the
terminal which is marked with the letter “L”
or coloured red.
1. Remove the fuse cover (A) and the fuse
(B).
2. Fit the replacement 13 A fuse into the fuse
cover.
3. Refit both into the plug.
For all other types of plug, the supply socket
should be protected by a 16 A fuse or circuit
breaker at the distribution board.
17
18010gb.fm5 Page 18 Tuesday, September 18, 2001 5:13 PM
VENT CONNECTION
When delivered from the factory the vent hose
with an adaptor is in the drum.
N.B.: When vent hose is not supplied it is
recommended to use the kit AMH 577 which is
available from your dealer
Vent hose mounting
1. Place a towel or the packaging beside the
dryer.
2. Lay the dryer down on the right side on the
towel or packaging (from the front).
3. Push the adaptor inside the hose (see
diagram). Mount the vent hose with adaptor
on the connecting branch below the dryer.
Ventilation to the outside
• Position the vent hose to the outside without
sharp bends (internal diameter 10 cm,
maximum length with 2 elbows: 3m).
• When stacking on a washing machine ensure
that the hose is horizontal or vertical. The
vent hose should not sag down.
• Do not mount any filter on the end of the
hose. The filter could block, reducing the
performance of your dryer.
•
•
Do not connect the vent hose to the heating
system.
Use only outlets insulated from the damp.
Without vent hose
• Use the dryer in large well ventilated room.
• Keep the room free of dust.
• The minimum distance from the air opening
to the wall must be at least 10 cm.
DOOR REVERSIBILITY
To change the direction of opening of the
door
1. Unplug the dryer.
2. Open the door.
3. Remove the contact pin at the upper part of
the door with a spanner. Turn the contact pin
90° and take it out.
4. Unscrew the 2 screws at the door hinge and
remove the door.
5. Unscrew the 2 screws above and below the
door lock system.
6. To remove the door lock:
• Press the hook at the upper part down with a
screwdriver, pull it forward and take the lock
system out.
7. To change the door opening:
• Turn the door.
• Re-fit the door with the 2 screws at the
preferred position.
• Hang the door lock system at the opposite
side of the door and latch it.
• Fix the 2 screws above and below the door
lock system.
8. Replace the contact pin in the top of the door.
18
18010gb.fm5 Page 19 Tuesday, September 18, 2001 5:13 PM
MAINTENANCE
1. Wipe the cabinet with a mild household
detergent. Avoid using abrasive cleaners.
2. Clean the lint filter at the end of each drying
cycle.
3. If the lint filter mesh is clogged, clean it with
water and a soft brush.
4. Wipe away fluff at the door seal and the
inside of the door using a damp cloth.
TROUBLE SHOOTING GUIDE
Should your dryer operate incorrectly, check the following points before calling for
a qualified service technician.
Drying is too long / laundry is not dry
enough:
• Have you selected the correct drying time or
programme?
• Was the inserted laundry too humid
(Washing machine spin speed less than
800rpm)?
• Is the lint filter dirty (filter indicator light on if
available)?
After an interruption in the mains supply you
must restart the dryer (Electronic dryer).
The dryer does not operate:
• Is the plug properly connected to the mains
supply?
• Is there a power failure?
• Has the fuse blown?
• Is the door well closed?
• Has the drying time or programme been
selected?
• Has the Start button been pressed?
Lint filter light on: (if available)
• Is the lint filter clean?
• Is the vent hose blocked?
AFTER-SALES SERVICE
Before contacting After-Sales Service
1. Try to solve the problem (see “Troubleshooting guide”).
2. Restart the programme to see if the fault is
repeated.
If after the above checks your dryer does not
work properly, get in touch with the nearest
After-Sales Service Centre.
Please give:
•
•
•
a short description of the fault.
the exact type and model of the dryer.
the service number visible on the right when
door is open.
•
Your correct address and telephone number.
19
">
