Contents
Quick Reference Guide
Programme Chart
Preparing the Laundry
Selecting a Programme and Options
Starting and Completing a Programme
Changing a Programme
Interrupting a Programme
Daily Maintenance and Cleaning
Instructions for Use
Booklet
Before Using the Dryer / Connections
Precautions and General
Recommendations
Description of the Dryer
Vent Connection
Door Reversibility
Troubleshooting Guide / After-Sales
Service
Before Using the Dryer / Connections
1. Removing the
packaging and check
After unpacking, make sure
that the dryer is
undamaged. If in doubt, do
not use the dryer. Contact
After-Sales Service or your
local retailer.
Keep the packaging
materials (plastic bags,
polystyrene parts, etc.) out
of reach of children, as they
are potentially dangerous.
2. Electrical Connections
Electrical connections must
be carried out by a qualified
technician in compliance
with the manufacturers
instructions and current
standard safety regulations.
Electrical connection must
comply with local Electricity
Board regulations.
Voltage information, power
consumption and the
required fuse protection is
shown on the rating plate
mounted at the rear of the
dryer.
The manufacturer cannot
accept any liability for
personal injury or damage
to property resulting from
failure to adhere to these
instructions.
The dryer must be earthed
as prescribed by law.
Do not use extension leads
or multiple adaptors.
Before any maintenance on
the dryer disconnect it from
the mains supply.
Do not operate the dryer if
it has been damaged during
transport. Contact one of
our After-Sales Service
technicians.
Mains cables must be
replaced by an original
cable and is only to be
carried out by a technician
from After-Sales Service or
an authorized electrician.
After installation access to
the mains plug has to be
guaranteed, or the all-pole
disconnection has to be
possible with a switch.
3. Installation
Do not install your dryer
where it can be subject to
extreme conditions, such as:
poor ventilation,
temperatures around
freezing (or above 35° C).
Remove the protective foil
from the control panel.
Stability:
When installing the dryer
always carefully level the
dryer adjusting the two
feet and check the correct
levelling with a spirit level.
To built in the dryer
For security reason do not
remove the worktop.
Connect the dryer to an
external ventilation system
in order to prevent steam
from damaging your
furniture during the years.
Stacking kit
Your dryer can be stacked
on top of your front
loading washing machine.
To do this, use stacking kit
AMH 752, available at your
dealer.
Minimum housing
dimensions:
Width:
600 mm
Height: 850 mm
Depth:
560 mm
Precautions and General Recommendations
1. Packing
The packing box may be
fully recycled as confirmed
by the
recycling symbol.
2. Energy saving tips
Always dry a full load:
depending on the type of
laundry and the
programme/drying time.
By preference use the
maximum spin speed
allowed by your washing
machine, since draining the
water mechanically requires
less energy.
Do not overdry the laundry.
Clean the lint filter after
every drying cycle.
Place your dryer in a room
with a temperature
between 15° C and 20° C. In
case of higher temperature
ventilate the room.
Always select the correct
programme/drying time for
the load in order to obtain
the desired drying results.
Select the gentle option
only with small loads.
When drying cotton, for
example: dry iron dry and
cupboard dry loads
together. Start with the iron
dry programme/drying time
setting, remove the laundry
to be ironed at the end of
that cycle and dry the
remainder of the load on
the cupboard dry setting.
3. Disposing of packaging
and old appliances
The dryer is built from
reusable materials. The
dryer must be disposed of
in compliance with local
waste disposal regulations.
Before scrapping, cut off
the power cable so that the
dryer cannot be connected
to the mains.
4. Child safety
Children must not be
allowed to play with the
dryer.
5. General
recommendations
Always set the programme/
time selector knob to the
0 position after use. This
prevents the dryer from
being switched on
accidentally.
Before cleaning or carrying
out maintenance, switch off
the dryer and disconnect it
from the mains supply.
To clean the outside of the
dryer, use a neutral
detergent and a damp
cloth.
Do not use abrasive
detergents.
Clean the lint filter at
the end of every drying
cycle:
1. Open the door.
2. Pull the filter upwards.
3. Remove lint using a soft
brush or your fingertips.
4. Push the filter firmly back
into place.
Wipe away lint from the
door seal and the door
using a damp cloth.
If the lint filter mesh is
clogged, clean it with water
and a soft brush.
If necessary, the power
cable may be replaced with
an identical one obtained
from our After-Sales
Service. The power cable
must only be replaced by a
qualified technician.
EC Declaration of
Conformity
This dryer has been
designed, constructed and
distributed in compliance
with the safety
requirements of EC
Directives:
73/23/EEC Low Voltage
Directive
89/336/EEC EMC Directive
93/68/EEC CE Marking
Directive.
The dryer must be used in
the household for the
described uses.
Description of the Dryer
A. Work top
B. Contact pin
A
C. Door
To open the door: pull the
handle.
To close the door: push
gently until closed.
D. Filter
B
D
Reminder Maintenance and
Cleaning
Filter
Clean the lint filter at the
end of every drying cycle:
Open the door.
Pull the filter upwards.
Remove lint using a soft
brush or your fingertips.
C
Vent Connection
In some dryer models the vent
hose together with an
adaptor is supplied in the
drum. If the hose and adaptor
are not supplied as a standard
the optional accessory
AMH 577 kit, available at your
dealer, can be used.
Installing the vent hose
A. Place a towel or the packing
material on the right-hand
side next to the dryer.
B. Place the dryer on its righthand side (seen from the
front) on the towel or the
packing material.
C. Push the adapter into the
hose (see illustration).
Attach the air vent hose
adapter to the connection
located under the dryer and
lock it by means of the
foreseen lugs.
Venting outside
Without kinking it, lead the
vent hose outside (inside
diameter 10 cm, maximum
length with two bends 3 m).
Ensure that the vent hose
does not sag when stacking
the dryer on a washing
machine. It should only be
placed horizontally or
upwards.
Do not connect to
ventilation systems
protected by fly nets. These
can become clogged and
cause malfunctioning of the
dryer.
Never connect the air vent
hose to a chimney or to a
mechanical ventilation
extractor duct.
Do not connect the vent
hose to the heating system.
Only connect the hose to
ventilation systems
insulated against humidity.
Dryer operation without
vent hose
Only use the dryer in a
large, well-ventilated room.
Keep the room free of dust.
A minimum distance of
10 cm between rear of
appliance and the wall
must be observed.
Dryer placed close to the
wall; venting to the left or
right
Install the dryer by using the
bi-directional kit AMH 869,
available at your dealer,
should be used.
C
Door Reversibility
Door Reversibility
A. Unplug the dryer.
C
B. Open the door.
C. Using a spanner, turn the
contact pin on the inside of
the door (top) through 90°
and remove it.
D.Remove the 2 door hinge
screws, followed by the
door.
E. Unscrew the 2 screws above
and below the door lock
system.
C
F. Removing the door lock:
using a screwdriver, press
down on the small rib in the
upper opening and extract
the door lock by pulling it
towards you.
G. Reverse the door:
H. Fasten the door on the
desired side using the
2 screws.
D
I. Insert the door lock system
on the opposite side and
lock it securely.
J. Fix the 2 screws above and
below the door lock system.
K. Replace the contact pin in
the inside of the door (top).
E
F
E
Troubleshooting Guide / After-Sales Service
Troubleshooting Guide
After-Sales Service
If a fault occurs, before
contacting our After-Sales
Service, make the
following checks to try
and remedy the problem:
If, after carrying out the
above checks the
malfunction persists or
appears again, turn the
dryer off and call our
After-Sales Service (refer
to guarantee).
Drying takes too long /
laundry is not dry enough:
Was the correct programme
selected?
Was the inserted laundry
too wet (Washing machine
spin speed less than
800 rpm)?
Is the lint filter dirty
(filter indicator lamp on)?
The dryer does not
operate:
(following a power failure
and/or interruption to the
mains supply, always
press the Start button).
Is the plug properly inserted
into the mains electricity
socket?
Is there a power failure?
Has the fuse blown?
Is the door well closed?
Has the programme been
selected?
Has the start delay option
been selected?
Has the Start/Pausebutton
been pressed?
Lint filter indicator lamp
on:
Is the lint filter clean?
Is the vent hose blocked?
Please specify:
The nature of the fault.
The dryer type and model.
The service code (the
number after the word
Service on the adhesive
rating plate) on the righthand side when the door is
open.
Your full address and phone
number.
Ecological Paper
5019 108 00454
Printed in Italy
GB
1/ 0501
">
