Whirlpool ADGU 862 IX Instruction for Use

IMPORTANT SAFETY INSTRUCTIONS
READ ALL THE INSTRUCTIONS BEFORE USING
• Check that the detergent comparment is empty
after completion of the wash cycle.
• Do not wash plastic items unless they are
marked dishwasher safe or the equivalent. For
plastic items not so marked, check the
manufacturer's recommendations.
• Use only detergent and rinse additives designed
for an automatic dishwasher.
• Never use soap, laundry detergent, or hand
washing detergent in your dishwasher. Keep
these products out of the reach of children.
• Keep children away from detergent and rinse
aid, keep children away from the open door of
the dishwasher, there could still be some
detergent left inside.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge,unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Children should be supervised to ensure that
they do not play with the appliance.
• Dishwasher detergents are strongly alkaline, they
can be extremely dangerous if swallowed. Avoid
contact with skin and eyes and keep children away
from the dishwasher when the door is open.
• The door should not be left open, since this
could increase the risk of tripping.
• If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
• Remove the door to the washing compartment
when removing an old dishwasher from service
or discarding it.
• Please dispose of packing materials properly.
• Use the dishwasher only for its intended function.
• During installation, the power supply must not
be excessively or dangerously bent or flattened.
Do not tamper with controls.
• The appliance is to be connected to the water
mains using new hose sets and that old hose-sets
should not be reused.
• The rated voltage is: AC 220-240 V/ 50Hz.
• The maximum number of place settings to be
washed is 9.
• The maximum permissible inlet water pressure
is 1Mpa.
• The minimum permissible inlet water pressure is
0.04Mpa.
WARNING:
When using your dishwasher, follow the
precautions listed below:
GROUNDING INSTRUCTIONS
• This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce
the risk of anelectric shock by providing a path of
least resistance of electric current. This appliance
is equipped with a cord having an equipmentgrounding conductor and a grounding plug.
• The plug must be plugged into an appropriate
outlet that is installed and grounded in
accordance with all local codes and ordinances.
• Usage of extension cord is not allowed.
WARNING:
Improper connection of the equipment-grounding
conductor can result in the risk of an electric shock.
• Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded. Do not modify
the plug provided with the appliance; If it does
not fit the outlet. Have a proper outlet installed
by a qualified electrician.
WARNING:
PROPER USE
• Access to disconnection of the appliance (main
plug) shall be ensured after installation.
• Do not abuse, sit on, or stand on the door or
dishrack of the dishwasher.
• Do not operate your dishwasher unless all
enclosure panels are properly in place. Open the
door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
• Do not place any heavy objects on or stand on
the door when it is open. The appliance could
tip forward.
• When loading items to be washed:
1) Locate sharp items so that they are not likely
to damage the door seal;
2) Warning: Knives and other utensils with sharp
points must be loaded in the basket with their
points down or placed in a horizontal position.
• When using your dishwasher, you should prevent
plastic items from coming into contact with the
heating element. (This instruction is only
applicable to machines with a visual heating
element.)
READ AND FOLLOW THIS SAFETY
INFORMATION CAREFULLY
KEEP THESE INSTRUCTIONS
35
SAFEGUARDING THE ENVIRONMENT
• This appliance has been made of recyclable or re-usable material. Scrapping must be carried out in
compliance with local waste disposal regulations. Before scrapping it, make sure to cut off the mains
cord so that the appliance cannot be re-used.
• For more detailed information on handling and recycling of this product, contact your local authorities
who deal with the separate collection of rubbish or the shop where you bought the appliance.
SCRAPPING OF PACKAGING
• The packaging can be 100% recycled as confirmed by the recycling symbol
. The various parts of
the packaging must not be dispersed in the environment, but must be scrapped in line with local
authority regulations.
SCRAPPING OF APPLIANCE
• This appliance is marked according to the European Directive 2002/96/EC, Waste Electrical and
Electronic Equipment (WEEE).
• By ensuring that this product is disposed of correctly, you will help to prevent potentially negative
consequences for the environment and for human health.
• The symbol
on the product or on the documents accompanying the product indicates that this
appliance should not be treated as household waste, but must be given to the appropriate local
gathering place where electric and electronic appliances are stored and recycled.
DISPOSAL
Dispose of the dishwasher packaging material correctly.
All packaging materials can be recycled.
Plastic parts are marked with the standard international abbreviations:
• PE for polyethylene, e.g. sheet wrapping material
• PS for polystyrene, e.g. padding material
• POM polyoxymethylene, e.g. plastic clips
• PP polypropylene, e.g. Salt filler
• ABS Acrylonitrile Butadiene Styrene, e.g. Control Panel.
WARNING:
• Packaging material could be dangerous for children!
• For disposing of package and the appliance please go to a recycling centre. Therefore cut off the power
supply cable and make the door closing device unusable.
• Cardboard packaging is manufactured from recycled paper and should be disposed in the waste paper
collection for recycling.
• By ensuring this product is disposed of correctly, you will help prevent potential negative consequences
for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product.
• For more detailed information about recycling of this product, please contact your local city office and
your household waste disposal service.
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such waste separately
for special treatment is necessary.
36
OPERATION INSTRUCTION
IMPORTANT. To get the best performance from your dishwasher, read all operating instructions before
using it for the first time.
Control panel
1
2
3
7
4
1 On/Off Button: To turn on/off the power supply.
2 Program Button: To Press the button to select a
wash Program.
3 Half Load Button: Press button to select half
load function and Half load icon will be lit.
4 Delay Button: To Press the button to delay.
5 Child lock button: press the buttons for 3
seconds to lock the program.
6 Start /Pause button: To start the selected
washing program or pause the washing program
when the machine is working.
7 Display screen: to show the reminding time and
the state (running state, delay time etc )
- Program indicators:
5
6
- Delay time, Remain time,
or error codes indicator:
Run/Pause icon:
- Rinse Aid indicator:
Indicates when the dispenser needs to be
refilled.
- Add salt indicator:
Indicates when the dispenser needs to be
refilled.
- Delay indicator:
- Half load icon:
- Child lock indicator:
- Tap icon:
When Forget to open the Water faucet or the
inlet valve was broken that make the machine
cannot income water, the icon can be light to
remaind consumer.
Dishwashing features
Front view
Back View
6
1
2
7
8
3
4
5
9
1 Upper Basket
2 Inner pipe
3 Lower Basket
4 Salt Container
5 Dispenser
6 Cup Shelf
10
7 Spray arms
8 Filter assembly
9 Inlet pipe connector
37
10 Drain pipe
PRIOR USING FOR THE FIRST TIME
Before using your dishwasher for the first time:
A. Set the water softener
B. Add 1.5Kg dishwasher salt and then full fill the salt container with water
C. Fill the rinse aid dispenser
D. Fill in detergent
A. Water Softener
The water softener must be set manually, using the water hardness dial. The water softener is designed to
remove minerals and salts from the water, which would have a detrimental or adverse effect on the
operation of the appliance. The higher the content of these minerals and salts, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area. Your local Water
Authority can advise you on the hardness of the water in your area.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed based on the hardness
of the water used. This is intended to optimise and customise the level o f salt consumption.
Please follow the steps below for adjustment in salt consumption.
1. Switch on the appliance;
2. Press the Start/Pause button for more than 5 seconds to start the water softener set model within
60seconds after the appliance was switched on( The Salt and Rinse aid warning lights will be on
periodically when it get in the set model );
3. Press the Start/Pause button to select the proper set according to your local environment, the sets will
change in the following sequence: H1->H2->H3->H4->H5->H6;
4. Press the Power button to end the set up model.
0~5
0~9
0~6
0~0.94
H1
Salt
consumption
(gram/cycle)
0
6~11
10~20
7~14
1.0~2.0
H2
9
12~17
21~30
15~21
2.1~3.0
H3
12
18~22
31~40
22~28
3.1~4.0
H4
20
23~34
41~60
29~42
4.1~6.0
H5
30
35~55
61~98
43~69
6.1~9.8
H6
60
WATER HARDNESS
°dH
°fH
°Clarke
mmol/l
Selector
position
Note 1
1 dH=1.25 Clarke=1.78 fH=0.178mmol/l
DH
= German degree
fH
= French degree
Clarke = British degree
Note 2
The manufactory setting: H4 (EN 50242)
Contact your local water board for information on the hardness of your water supply.
Note: If your model does not have any water softener, you may skip this section.
Water softener
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will
form on the dishes and utensils.
The appliance is equipped with a special softener that uses a salt container specifically designed to
eliminate lime and minerals from the water.
38
B. Loading the Salt Into the Softener
Always use the salt intended for use with dishwasher.
The salt container is located beneath the lower basket and should be filled as explained in the following:
Attention
• Only use salt specifically designed for the use in dishwashers! Every other type of salt not specifically
designed for the use in a dishwasher, especially table salt, will damage the water softener. In case of
damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is liable
for any damages caused.
• Only fill with salt just before starting one of the complete washing programs. This will prevent any
grains of salt or salty water, which may have been spilled, remaining on the bottom of the machine for
any period of time, which may cause corrosion.
Open
1
A. After the lower basket has been removed, unscrew and remove the cap from the salt container. (1)
B. Place the end of the funnel (supplied) into the hole and introduce about 1.5kg of dishwasher salt.
C. Full fill the salt container with water,It is normal for a small amount of water to come out of the salt
container. (2).
D. After filling the container , screw the cap tightly back clockwise.
E. The salt warning light will stop being after the salt container has been filled with salt.
F. Immediately after filling the salt into the salt container, a washing program should be started program
Otherwise the filter system, pump or other important parts of the machine may be damaged by salty
water. This is out of warranty.
Note:
1. The salt container must only be refilled when the salt warning light in the control panel comes on.
Depending on how well the salt dissolves, the salt warning light may still be on even though the salt
container is filled. If there is no salt warning light in the control panel (for some Models),you can
estimate when to fill the salt into the softener by the cycles that the dishwasher has run.
2. If there are spills of the salt, a soak or a rapid program should be run to remove the excessive salt.
3. If the machine needs to be dumped for the reasons of transit, repair and so on, please use the bibulous
cloth or analog to blot up the water in the salt container, and screw the cap tightly, afterward, transit
or repair the machine. After transiting or repairing the machine and confirming it in order, load the salt
into the softener according to the process of “B. Loading the salt into the Softener”. Otherwise, it
could be make the big damage to the machine, for example, rustiness, conk and so on. Such problems
are out of the guarantee range.
39
C. Fill the Rinse Aid Dispenser
Rinse Aid Dispenser
The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes,
which can leave spots and streaks. It also improves drying by allowing water to roll off the dishes. Your
dishwasher is designed to use liquid rinse aids. The rinse aid dispenser is located inside the door next to
the detergent dispenser.
To fill the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns
completely black. The volume of the rinse aid container is about 110ml.
Function of Rinse Aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free
drying.
Attention
Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.
When to Refill the Rinse Aid Dispenser
If there is no rinse-aid warning light in the control panel, you can estimate the amount from the colour of
the optical level indicator C located next to the cap. When the rinse-aid container is full, the whole
indicator will be dark .As the rinse-aid diminishes, the size of the dark dot decreases. You should never let
the rinse aid level fall 1 / 4 full.
As the rinse aid diminishes, the size of the black dot on the rinse aid level indicator changes, as illustrated
below.
C (Rinse-Aid indicator)
Full
3 / 4 full
1 / 2 full
1 / 4 full - Should refill to eliminate spotting
Empty
40
1. To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
2. Pour the rinse aid into the dispenser, being careful not to overfill.
3. Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
NOTE
Clean up any rinse aid spilled while during filling with an absorbent cloth to avoid excessive foaming during
the next wash. Don't forget to replace the cap before you close dishwasher door.
Adjusting Rinse Aid Dispenser
The rinse aid dispenser has six or four settings. Always start
with the dispenser set on "4". If spots and poor drying are a
problem, increase the amount of rinse aid dispensed by
removing the dispenser lid and rotating the dial to "5". If the
dishes still are not drying properly or are show spots, adjust
the dial to the next higher lever until your dishes are spot-free.
The recommended setting is "4". (Factory value is "4".)
Adjust lever
(Rinse)
NOTE
Increase the dose if there are drops of water or lime spots on
the dishes after washing.
Reduce it if there are sticky whitish stains on your dishes or a bluish film on glassware or knife blades.
41
D. Function of Detergent
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of
the dishwasher. Most of the commercial quality detergents are suitable for this purpose.
Attention!
Proper Use of Detergent.
Use only detergent specifically made for the use in dishwashers. Keep your detergent fresh and dry.
Don't put powdered detergent into the dispenser until you're ready to wash dishes.
Detergents
There are 3 sorts of detergents
1.With phosphate and with chlorine
2.With phosphate and without chlorine
3.Without phosphate and without chlorine
Normally new pulverised detergent is without phosphate. Thus the water softener function of
phosphate is not given. In this case we recommend to fill salt in the salt container even when
the hardness of water is only 6 dH. If detergents without phosphate are used in the case of hard water
often white spots appear on dishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Strong and coloured spots will not
be removed completely. In this case please choose a program with a higher temperature.
Concentrated Detergent
Based on their chemical composition, detergents can be split in two basic types:
• conventional, alkaline detergents with caustic components
• low alkaline concentrated detergents with natural enzymes
The use of normal washing programs in combination with concentrated detergents reduces pollution and is
good for your dishes; these wash programs are specifically matched to the dirt-dissolving properties of the
enzymes of the concentrated detergent. For this reason normal wash programs in which concentrated
detergents are used can achieve the same results that can otherwise only be achieved using intensive programs.
Detergent Tablets
Detergent tablets of different brands dissolve at different speeds. For this reason some detergent tablets
cannot dissolve and develop their full cleaning power during short programs. Therefore please use long
programs when using detergent tablets, to ensure the complete removal of detergent residuals.
Detergent Dispenser
The dispenser must be refilled before the start of each wash cycle following the instructions provided in
the wash cycle table . Your dishwasher uses less detergent and rinse aid than Conventional dishwasher.
Generally, only one tablespoon of detergent is needed for a normal wash load. More heavily soiled items
need more detergent. Always add the detergent just before starting the dishwasher, otherwise it could get
damp and will not dissolve properly.
Amount of Detergent to Use
Detergent powder
Push latch to open
Detergent tablet
42
NOTE:
• If the lid is closed: press release button. The lid will spring open.
• Always add the detergent just before starting each wash cycle.
• Only use branded detergent aid for dishwasher.
WARNING:
Dishwasher detergent is corrosive! Take care to keep it out of reach of children.
Fill in Detergent
Fill the detergent dispenser with detergent. The marking indicates the dosing levels, as illustrated on the
right:
A. The place of main wash cycle detergent placed.
B. The place of pre-wash cycle detergent placed.
Please observe the manufacturers dosing and storage.
Recommendations as stated on the detergent packaging.
Close the lid and press until it locks in place.
If the dishes are heavily soiled, place an additional detergent
dose in the pre-wash detergent chamber. This detergent will
take effect during the pre-wash phase.
NOTE:
• You find information about the amount of detergent for
the single programme on the last page.
• Please aware, that according to the level soiling and the
specific hardness of water differences are possible.
• Please observe the manufacturer's recommendations on
the detergent packaging.
43
LOADING THE DISHWASHER BASKET
Recommendation
• Consider buying utensils which are identified as dishwasher-proof.
• Use a mild detergent that is described as 'kind to dishes'. If necessary, seek further information from
the detergent manufacturers.
• For particular items, select a program with as low a temperature as possible.
• To prevent damage, do not take glass and cutlery out of the dishwasher immediately after the
programme has ended.
For washing in the dishwasher the following cutlery/dishes
Are not suitable
• Cutlery with wooden, horn china or mother-of-pearl handles
• Plastic items that are not heat resistant
• Older cutlery with glued parts that are not temperature resistant
• Bonded cutlery items or dishes
• Pewter or cooper items
• Crystal glass
• Steel items subject to rusting
• Wooden platters
• Items made from synthetic fibres
Are of limited suitability
Some types of glasses can become dull after a large number of washes
Silver and aluminum parts have a tendency to discolour during washing
Glazed patterns may fade if machine washed frequently
Attention before or after loading the Dishwasher Baskets
(For best performance of the dishwasher, follow these loading guidelines. Features and appearance of
baskets and cutlery baskets may vary from your model.)
Scrape off any large amounts of leftover food. Soften remnants of burnt food in pans.
It is not necessary to rinse the dishes under running water.
Place objects in the dishwasher in following way:
1. Items such as cups, glasses, pots/pans, etc. are faced downwards.
2. Curved items, or ones with recesses, should be loaded aslant so that water can run off.
3. All utensils are stacked securely and can not tip over.
4. All utensils are placed in the way that the spray arms can rotate freely during washing.
NOTE: Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
• Load hollow items such as cups, glasses, pans etc. With the opening facing downwards so that water
cannot collect in the container or a deep base.
• Dishes and items of cutlery must not lie inside one another, or cover each other.
• To avoid damage to glasses, they must not touch.
• Load large items which are most difficult to clean into the lower basket.
• The upper basket is designed to hold more delicate and lighter dishware such as glasses, coffee and tea
cups
• Long bladed knives stored in an upright position are a potential hazard!
• Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper
basket.
• Please do not overload your dishwasher. This is important for good results and for reasonable
consumption of energy.
Removing the Dishes
To prevent water dripping from the upper basket into the lower basket, we recommend that you empty
the lower basket first and then the upper basket.
44
The Method Loading Normal Dishware
Loading the Upper Basket
The upper basket is designed to hold more delicate and lighter
dishware such as glasses, coffee and tea cups and saucers, as well as
plates, small bowls and shallow pans (as long as they are not too
dirty).
Position the dishes and cookware so that they will not get moved by
the spray of water.
Loading the Lower Basket
We suggest that you place large items and the most difficult to clean
items are to be placed into the lower basket: such as pots, pans, lids,
serving dishes and bowls, as shown in the figure below. It is
preferable to place serving dishes and lids on the side of the racks in
order to avoid blocking the rotation of the top spray arm.
Please be reminded that:
• Pots, serving bowls, etc, must always be placed top down.
• Deep pots should be slanted to allow water to flow out.
• The Bottom Basket features folding spikes so that larger or more
pots and pans can be loaded.
Adjusting the Upper Basket
The height of the upper basket can be adjusted in order
to create more space for large utensils both for the
upper /lower basket. The height of the upper basket can
be adjusted by placing the wheels on different height of
the rails. Long items, serving cutlery, salad servers and
knives should be placed on the shelf so that they do not
obstruct the rotation of the spray arms.
IN
IN
Lower position
Wheels
Folding back the cup shelives
For better stacking of pots and pans, the spikes can be
folded down as show in the picture right.
Folding Spikes of Lower Basket
For better stacking of pots and pans, the spikes can be folded down as show in the
picture right.
45
Upper position
Cutlery Basket
Cutlery should be placed in the cutlery basket with the handles at the bottom. If the rack has side baskets,
the spoons should be loaded separately into the appropriate slots, especially long utensils should be placed
in the horizontal position at the front of the upper basket as shown in the picture.
WARNING:
• Do not let any item extend through the bottom.
• Always load sharp utensils with the sharp point down!
For personal safety and a top quality cleaning, place the silverware in the basket making sure
that:
• They do not nest together.
• Silverware is placed with the handles-down.
• But place knives and other potentially dangerous utensils are placed handles-up.
46
STARTING A WASHING PROGRAMME
Wash Cycle Table
•
•
•
•
•
NOTE
• Means: need to fill rinse into the Rinse-Aid
Dispenser.
• * This programme is the test cycle. The
information for comparability test in
Program
Intensive
Normal
Cycle selection
information
Energy
(Kwh)
Water Rinse
(l)
Aid
Pre-wash (50°C)
Wash (65°C)
Rinse
Rinse
Rinse (65°C)
Drying
5/22g
(or3in1)
135
1.30
16
For normally soiled loads,
such as pots plates glasses
and lightly soiled pans.
Pre-wash (45°C)
Wash (55°C)
Rinse
Rinse (65°C)
Drying
5/22g
(or3in1)
155
1.07
13
Pre-wash
Wash (50°C)
Rinse (65°C)
Drying
5/22g
(or3in1)
175
0.78
9
Pre-wash
Wash (40°C)
Rinse
Rinse (60°C)
Drying
5/22g
110
0.70
13
For lightly soiled loads that
do not need excellent drying
efficiency.
Pre-wash (50°C)
Wash(60°C)
Rinse (55°C)
Drying
5/22g
60
0.85
9
A shorter wash for lightly
soiled loads and quick wash.
Wash (40°C)
Rinse
Rinse (45°C)
20g
40
0.45
10
For lightly soiled crockery
and glass.
Glass
Rapid
Description Detergent Running
of cycle
pre/main time (min)
For heaviest soiled crockery,
and normally soiled pots
pans dishes etc with dried
on soiling.
This is standard programme,
it is suitable to clean
normally soiled tableware
and it is the most efficient
.
programme in terms of its
* EN 50242 combined energy and water
consumption for that type of
tableware.
1 Hour
accordance with EN 50242, as follows:
Capacity: 9 setting;
Position Upper basket: upper wheels on rails;
Rinse aid setting: 6;
Pl: 0.49w;
Po: 0.45w.
Turning On the Appliance
Starting a cycle wash
1. Draw out the lower and upper basket, load the dishes and push them back. It is commended to load
the lower basket first, then the upper one (see the section entitled “Loading the Dishwasher”).
2. Pour in the detergent (see the section entitled “Salt, Detergent and Rinse Aid”).
3. Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification of the
socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.
4. Close the door, press the On/Off button to switch on the machine.
5. Press the program button, the wash program will be changed as follows direction:
Intensive->Normal->ECO->Glass->1 Hour->Rapid;
If a program is selected, the response light will light on. Then press the Start/Pause button, the
dishwasher begins to start.
47
NOTE: When you press the Start/Pause button to pause during washing, the LED display window
will stop blinking and the dishwasher will mooing every minute unless you press the Start/Pause button to
start.
Change the Program...
Premise:
1. A cycle that is underway can only be modified if it has only been running for a short time. Otherwise,
the detergent may have already been released, and the appliance may have already drained the wash
water. If this is the case, the detergent dispenser must be refilled (see the section entitled “Loading the
Detergent”).
2. Press the Start/Pause button, the machine will pause, press the program button more than 3s then you
can change the program to the desired cycle setting (see the section entitled “Starting a wash cycle. . .”).
Forgot to Add a Dish?
A forgotten dish can be added any time before the detergent cup opens.
1. Press the Start/Pause Button to stop the washing.
2. Open the door a little .
3. After the spray arms stop working, you can open the door completely.
4. Add forgotten dishes.
5. Close the door.
6. Press the Start/Pause Button, the dishwasher will run after 10 seconds.
At the End of the Wash Cycle
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop.
Turn off the appliance using the ON/OFF button, shut off the water supply and open the door of the
dishwasher. Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and
utensils while they are still hot and more susceptible to breakage. They will also dry better.
• Switch Off the Dishwasher
The program light is on but is not blinking, only in this case the programme has ended.
1. Switch off the dishwasher by pressing the ON/OFF button.
2. Turn off the water tap!
• Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15
minutes before removing from the appliance. Open the dishwasher's door, leave it ajar and wait a few
minutes before removing the dishes. In this way they will be cooler and the drying will be improved.
• Unloading the dishwasher
It is normal that the dishwasher is wet inside. Empty the lower basket first and then the upper one.
This will avoid water dripping from the upper Basket onto the dishes in the lower one.
WARNING:
It is dangerous to open the door when washing, because the hot water may scald you.
48
MAINTENANCE AND CLEANING
Filtering System
The filter prevents larger remnants of food or other objects from getting inside the pump.
The residues may block the filter, in this case they must be removed.
The filter system consists of a coarse filter, a flat (Main filter) and a microfilter(Fine filter).
Main filter 1
Food and soil particles trapped in this filter are
pulverized by a special jet on the lower spray arm and
washed down to drain.
Coarse filter 2
Larger items, such as pieces of bones or glass, that could
block the drain are trapped in the coarse filter. To
remove the items caught by the filter, gently squeeze the
tap on the top of this filter and lift out.
Fine filter 3
This filter holds soil and food residues in the sump area
and prevents it from being redeposit on the dishes
during wash cycle.
1
2
3
Filter assembly
The filter efficiently removes food particles from the wash water, allowing it to be recycled during the
cycle. For best performance and results, the filter must be cleaned regularly. For this reason, it is a good
idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the
semicircular filter and cup under running water. To remove the filter device, pull the cup handle in the
upward direction.
WARNING:
• The dishwasher must never be used without the filters.
• Improper replacement of the filter may reduce the performance level of the appliance and damage
dishes and utensils.
STEP 1: Turn the filter in anti-clockwise direction,
Open
STEP 2: lift the filter assy up
1
NOTE
When following this procedure from step1 to step 2, the filter system will
be removed; when following it from Step 2 to Step 1, the filter system will
be installed.
2
49
Remarks:
• Inspect the filters for blocking after every time the dishwasher has been used.
• By unscrewing the coarse filter, you can remove the filter system. Remove any food remnants and
clean the filters under running water.
NOTE: The entire filter assembly should be cleaned once a week.
Cleaning the Filter
To clean the coarse filter and the fine filter, use a cleaning brush. Reassemble the filter parts as shown in
the figures on the last page and reinsert the entire assembly in the dishwasher, positioning it in its seat and
pressing downwards.
WARNING:
When cleaning the filters, don't knock on them. Otherwise, the filters could be contorted and the
performance of the dishwasher could be decreased.
Caring for the Dishwasher
The control panel can be cleaned by using a lightly dampened cloth.
After cleaning, make sure to dry it thoroughly.
For the exterior, use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any
part of the dishwasher.
Cleaning The Door
To clean the edge around the door, you should use only a soft
warm, damp cloth. To avoid penetration of water into the door lock
and electrical components, do not use a spray cleaner of any kind.
WARNING:
• Never use a spray cleaner to clean the door panel as it may damage the door lock and electrical
components.
• Abrasive agents or some paper towels should not be used because of the risk of scratching or leaving
spots on the stainless steel surface.
Protect Against Freezing
please take frost protection measures on the dishwasher in winter. Every time after washing cycles, please
operate as follows
1.
2.
3.
4.
5.
Cut off the electrical power to the dishwasher.
Turn off the water supply and disconnect the water inlet pipe from the water valve.
Drain the water from the inlet pipe and water valve. (Use a pan to gather the water)
Reconnect the water inlet pipe to the water valve.
Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.
NOTE: If your dishwasher cannot work because of the ice, please contact professional service persons.
50
Cleaning the Spray Arms
It is necessary to clean the spray arms regularly for hard water chemicals
will clog the spray arm jets and bearings.
To remove the upper spray arm, hold the nut, rotate the arm clockwise
to remove it.
To remove the lower spray arm, pull out the spray arm upward.
Wash the arms in soapy and warm water and use a soft brush to clean the
jets. Replace them after rinsing them thoroughly.
Open
How to Keep Your Dishwasher in Shape
• After Every Wash
After every wash, turn off the water supply to the appliance and leave the door slightly open so that
moisture and odours are not trapped inside.
• Remove the Plug
Before cleaning or performing maintenance, always remove the plug from the socket.
• No Solvents or Abrasive Cleaning
To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning
products. Only use a cloth with warm soapy water. To remove spots or stains from the surface of the
interior, use a cloth dampened with water and a little vinegar, or a cleaning product made specifically
for dishwashers.
• When not in Use for a LongTime
It is recommend that you run a wash cycle with the dishwasher empty and then remove the plug from
the socket, turn off the water supply and leave the door of the appliance slightly open. This will help
the door seals to last longer and prevent odours from forming within the appliance.
• Moving the Appliance
If the appliance must be moved, try to keep it in the vertical position. If absolutely necessary, it can be
positioned on its back.
• Seals
One of the factors that cause odours to form in the dishwasher is food that remains trapped in the
seals. Periodic cleaning with a damp sponge will prevent this from occurring.
51
INSTALLATION INSTRUCTIONS
ATTENTION The installation of the pipes and electrical equipments should be done by professionals.
WARNING:
Electrical Shock Hazard
Disconnect electrical power before installing dishwasher. Failure to do so can result in death or electrical
shock.
Installation preparation
The installation position of dishwasher should be near the existing inlet and drain hoses and power cord.
One side of the cabinet sink should be chosen to facilitate the connection of drain hoses of the dishwasher.
NOTE: please check the accompanying installation accessories(hook for aesthetic panel, screw)
Please carefully read the installation instruction.
Illustrations of cabinet dimensions and installation position of the dishwasher
Preparations should be made before moving the dishwasher to the installation place.
1. Choose a place near the sink to facilitate the installation of inlet and drain hoses (see figure 1).
2. If dishwasher is installed at the corner of the cabinet, there should be some space (illustrated in figure
2) when the door is opened.
Electrical, drain
and water supply
line entrances
Space between cabinet
bottom and floor
Figure 1
Cabinet dimensions
Less than 5mm between the top of dishwasher and cabinet and the outer door aligned to cabinet.
52
Figure 2
Minimum space when the door is opened.
Dishwasher
Cabinet
Door of
dishwasher
Minimum space of
50 mm
Aesthetic panel's dimensions and installation
1. The aesthetic wooden panel could be processed according to the Figure 3.
439
416
0.2
390
0.2
75
127
0.2
62
2- 2 dp8
2 - 11
0.2
2- 5.5
287.5
517
710(MAX)
474.8
5
20
MAX
8- 2 dp8
30
38
286
4- 2 dp8
Unit: mm
Figure 3
The aesthetic panel should be processed in accordance with the illustrated dimensions.
53
2. Magical paster A and magical paster B be disjoinedon ,magical paster A on the aesthetic wooden panel
and felted magical paster B of the outer door of dishwasher (see figure 4a). After positioning of the
panel , fix the panel onto the outer door by screws and bolts (See figure 4b)
Figure 4a
Installation of aesthetic panel.
magical paster
magical paster
Figure 4b
Installation of aesthetic wooden panel
Take away the four short screws
1. take away the four short screws
2. pin up the four long screws
54
Pin up the four long screws
Tension adjustment of the door spring
The door springs are set at the factory to the proper tension for the outer door.
If aesthetic wooden panel are installed, you will have to adjust the door spring tension.
Rotate the adjusting screw to drive the adjustor to strain or relax the steel cable (see figure 5).
Figure 5
Tension adjustment of the door spring.
Connection of drain hoses
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making
sure to avoid bending or crimping it. The top of the hose must be less than 1000mm.
Counter
Front
NOTE
The top of the hose must be
less than 1000mm.
Drain pipe
PLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A, B
Figure 6
55
Dishwasher installation steps
1. Install the furniture door to the outer door of the dishwasher using the brackets provided. Refer to the
template for positioning of the brackets.
2. Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to tighten
the left and right door springs. Failure to do this could cause damage to your dishwasher (illustration 2).
3. Connect the inlet hose to the cold water supply.
4. Connect the drain hose. Refer to diagram. (Fig. 6).
5. Connect the power cord.
6. Affix the condensation strip under the work surface of cabinet. Please ensure the condensation strip is
flush with edge of work surface.
7. Place the dishwasher into position. (Illustration 4)
8. Level the dishwasher. The rear food can be adjusted from the front of the dishwasher by turning the
Allen screw in the middle of the base of dishwasher use an Allen key (Illustration 5A). To adjust the
front feet, use a flat screw driver and turn the front feet until the dishwasher is level (Illustration 5B).
9. The dishwasher must be secured in place. There are two ways to do this:
A. Normal work surface: Put the installation hook into the slot of the side plane and secure it to the
work surface with the wood screws (Illustration 6).
B. Marble or granite work top:Fix the side with Screw. (Illustration 7).
Condensation strip
r
re doo
Furnitu
Figure 7
56
Dishwasher must be level for proper dish rack operation and wash performance.
1. Place a spirit level on door and rack track inside the tub as shown to check that the dishwasher is level.
2. Level the dishwasher by adjusting the three levelling legs individually.
3. When level the dishwasher, please pay attention not to let the dishwasher tip over.
Check level
fron to back
Check level side to side
Figure 8
Illustration of feet adjustment.
NOTE: The maximum adjustment height of the feet is 50 mm.
About electricity connecting
WARNING:
For personal safety:
• DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
• DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
Electrical requirements
Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate
power supply. Use the required fuse 10 amp, time delay fuse or circuit breaker recommended and
provide separate circuit serving only this appliance.
WARNING:
Insure proper ground exists before use
Electrical connection
Ensure the voltage and frequency of the power being corresponds to those on the rating plate. Only insert
the plug into an electrical socket which is earthed properly. If the electrical socket to which the appliance
must be connected is not appropriate for the plug, replace the socket, rather than using a adaptors or the
like as they could cause overheating and burns.
Groundig instruction
This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk
of electric shock by providing a path of least resistance for the electric current. This appliance is equipped
with a cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into
an appropriate outlet that is installed and earthed in accordance with all local standards and requirements.
57
WARNING:
In order to avoid that there is more water staying in the inlet hose,
please close the hydrant after using.(For the models: no safety inlet hose.)
Water Connection
Connect the cold water supply hose to a threaded 3/4(inch) connector
and make sure that it is fastened tightly in place. If the water pipes are
new or have not been used for an extended period of time, let the
water run to make sure that the water is clear. This precaution is
needed to avoid the risk of the water inlet to be blocked and damage
the appliance.
WARNING:
Please close the hydrant after using.
Positioning the Appliance
Position the appliance in the desired location. The back should rest against the wall behind it, and the
sides, along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses
that can be positioned either to the right or the left sides to facilitate proper installation.
How to Drain Excess Water From Hoses
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directly into the sink.
It will be necessary to drain excess water from hoses into a bowl or suitable container that is held outside
and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water inlet hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.
Syphon Connection
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink,
making sure to avoid bending or crimping it. The top of the hose must be less than 1000mm.
Start of Dishwasher
The following things should be checked before starting the dishwasher.
1 The dishwasher is level and fixed properly
2 The inlet valve is open
3 There is a leakage at the connections of the conducts
4 The wires are tightly connected
5 The power is switched on
6 The inlet and drain hoses are knotted
7 All packing materials and printings should be taken out from the dishwasher
Attention: After installation, please make sure to keep this manual. The content of this manual is very
helpful to the users.
58
TROUBLESHOOTING GUIDE
Before Calling for Service
Review the charts on the following pages may save you from calling for service.
Technical problems
Problem
Possible causes
What to do
Dishwasher
doesn’t start
Fuse blown, or the
circuit breaker acted
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not
turned on
Make sure the dishwasher is turned on and the door is
closed securely. Make sure the power cord is properly
plugged into the wall socket.
Water pressure is low
Check that the water supply is connected properly and
the water is turned on.
Door of dishwasher
not properly closed.
Make sure to close the door properly and latch it.
water not pumped Kink in drain hose
form dishwasher
Filter clogged
Check drain hose.
Check coarse the filter
(see section titled " Cleaning The Filter ")
Kitchen sink clogged
Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for
dishwashers.
Problem
Possible causes
What to do
Suds in the tub
Improper detergent
Use only the special dishwasher detergent to avoid suds. If this
occurs, open the dishwasher and let suds evaporate. Add 1 gallon
of cold water to the tub. Close and latch the dishwasher, then
select any cycle. Dishwasher will drain out the water at the first
step. Open the door after draining is stop and check if the suds is
disappeared. Repeat if necessary.
Spilled rinse-aid
Always wipe up rinse-aid spills immediately.
Stained tub
interior
Detergent with
colourant was used
Make sure that the detergent is the one without
colourant.
White film on
inside surface
Hard water minerals
To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher
detergent for the risk of foaming or suds.
There are rust
stains on cutlery
The affected items are
not corrosion resistant.
–
A programme was not run
after dishwasher salt was
added. Traces of salt have
gotten into the wash cycle.
Always run the quick wash programme .
without any crockery in the dishwasher and
without selecting the Turbo function (if present),
after adding dishwasher salt.
The lid of the softer
is loose
Check the lip .Ensure the fix is fine.
General problems
59
Noise
Problem
Possible causes
What to do
Knocking noise
in the wash
cabinet
A sp ay arm is
knocking against
an item in a basket
Interrupt the programme, and rearrange the items
which are obstructing the spray arm.
Rattling noise
in the wash
cabinet
Items of crockery
are loose in the
wash cabinet
Interrupt the programme,
and rearrange the items of crockery.
Knocking noise
in the water pipes
This may be caused by on- This has no influence on the dishwasher function.
site installation or the
if in doubt, contact a suitably qualified plumber.
cross-section of the piping.
Unsatisfactory washing result
Problem
Possible causes
The dishes are not The dishes were not
clean
loaded correctly.
What to do
See notes in " Loading the Dishwasher Baskets ".
The programme was
not powerful enough.
Select a more intensive programme.
See" Wash Cycle Table ".
Not enough detergent
was dispensed.
Use more detergent, or change your detergent.
Items are blocking
the path of spray arms.
Rearrange the items so that the spray can rotate freely.
The filter combination in
Clean and/or fit the filter combination correctly.
the base of wash cabinet is Clean the sp ay arm jets. See "Cleaning the Spray
not clean or is not
Arms".
correctly fitted. This may
cause the sp ay arm jets
to get blocked.
Cloudiness
on glassware
Combination of soft
water and too much
detergent.
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Black or gray
marks on dishes
Aluminum utensils have
rubbed against dishes.
Use a mild abrasive cleaner to eliminate those marks.
Detergent left in
dispenser cups
Dishes block
detergent cups.
Re-loading the dishes properly.
60
Unsatisfactory drying result
Problem
Possible causes
The dishes are not Improper loading
drying
What to do
Load the dishwasher as suggested in the directions.
Too little rinse-aid
Increase the amount of rinse-aid/refill the rinse-aid
dispenser.
Dishes are removed
too soon
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once the
dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
Wrong program
has been selected
In short program the washing temperature is lower.
This also lowers cleaning performance. Choose a
program with a long washing time.
Use of cutlery with
a low-quality coating
Water drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.
Error codes
When some malfunctions come on, the appliance will display error codes to warn you:
Codes
Meanings
Possible causes
E1
Longer inlet time.
Faucets is not opened, or water intake is restricted,or
water pressure is too low.
E4
Overflow
Some element of dishwasher leaks.
WARNING:
• If overflow occurs, turn off the main water supply before calling a service.
• If there is water in the base pan because of an overfill or small leak, the water should be
removed before restarting the dishwasher.
61
TECHNICAL INFORMATION
(with th 570
e door
closed)
448
815
1150
Height
815 mm
Width
448 mm
Depth
570 mm (with the door closed)
Water pressure
0.04-1.0 MPa
Power supply
See rating label
Capacity
9 place settings
62
Loading the baskets according to En 50242
Upper basket
Cups
Sauces
Glasses
Small serving bowl
Medium serving bowl
Large serving bowl
Lower basket
Dessert dishes
Dinner plates
Soup plates
Oval platter
Cuttlery basket
➡ IN
1 Soup spoons
5 Dessert spoons
2 Forks
6 Serving spoons
3 Knives
7 Serving forks
4 Teaspoons
8 Gravy ladles
Information for compatibility tests in
accordance with EN 50242
Capacity: 9 place settings
Position of the upper basket: lower
position
Programma: ECO
Rinse aid setting: 6
Softener setting: H4
63
Technical Data Sheet
Sheet of household dishwasher according to EU Directive 1059/2010:
Manufacturer
WHIRLPOOL
Standard place settings
9
1
Energy efficiency class )
A+
Annual energy consumption 2)
222 kWh
Energy consumption of the standard cleaning cycle
0.77 kWh
Power consumption of off-mode
0.45 W
Power consumption of left-on mode
0.49 W
3
Annual water consumption )
2520 litre
Drying efficiency class 4)
A
5
Standard cleaning cycle )
ECO 50°C
Program duration of the standard cleaning cycle
170 min
Noise level
48/50 dB(A)re 1pW
Mounting
Semi-integrated
Height
81.5 cm
Could be built-in
Yes
Width
44.8 cm
Depth (with connections)
57.0 cm
Power consumption
1930 W
Rated voltage / frequency
AC220-240v/50Hz
Water pressure (flow pressure)
0.4-10 bar=0.04-1Mpa
NOTE
1
) A+ + + (highest efficiency) to D (lowest efficiency)
2
) Energy consumption 211 kWh per year, based on 280 standard cleaning cycles using cold water fill and
the consumption of the low power modes. Actual energy consumption will depend on how the
appliance is used.
3
) Water consumption 2380 litre per year, based on 280 standard cleaning cycles. Actual water
consumption will depend on how the appliance is used.
4
) A (highest efficiency) to G (lowest efficiency)
5
) This program is suitable for cleaning soiled normally soiled tableware and that it is the most efficient
programme in terms of its combined energy and water consumption for that type of tableware.
The device meets the European standards and the directives in the current version at delivery:
- LVD 2006/95/EC
- EMC2004/108/EC
- ErP 2009/125/EC
The above values have been measured in accordance with standards under specified operating
conditions.
Results may vary greatly according to quantity and pollution of the dishes, water hardness, amount of
detergent, etc.
The manual is based on the European Union's standards and rules.
64
QUICK OPERATION GUIDE
For detailed operating method read the corresponding content on the instruction manual.
Switch on the
appliance
Fill the detergent
dispenser
Press the On/Off button to switch on the appliance, Open the door.
Compartment A:
With each wash cycle.
Compartment B:
For programmes with pre-wash only.(Follow the user instructions!)
Check the rinse aid
level
Mechanical indicator C.
Electric indicator on control panel (if provided).
Check the
regeneration
salt level
On models with water softener system only.)
Electric indicator on control panel (if provided).
If there is no salt warning light in the control panel (for some models), you can
estimate when to fill the salt into the softener by the number of cycles the dishwasher
has run.
Load the baskets
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions
Select a program
Close the door, press the program button until the selected program indicator lights up. (See the
section entitled “Operation instruction”)
Running the
dishwasher
Turn on the water tap and press the Start/Pause Button. The machine will start working after
about 10 seconds.
1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
Changing the program
2. Press the Start/Pause button, the machine will pause, press the program button more than 3 seconds
then you can change the program to the desired cycle setting.
3. Press the Start/Pause Button, the dishwasher will run after 10 seconds
WARNING!
Open the door
carefully.
Hot steam may
escape when the
door is opened
Add forgotten dishes
in the dishwasher.
1. Press the Start/Pause Button to stop the washing.
2. Open the door a little .
3. After the spray arms stop working, you can open the door completely.
4. Add forgotten dishes.
5. Close the door
6. Press the Start/Pause Button, the dishwasher will run after 10 seconds.
If the appliance is
switched off during a
wash cycle.
If the appliance is switched off during a wash cycle, when switched on again, please re-select the
washing cycle and operate the dishwasher according to the original ”Power-on state”).
Switch off the
appliance
When the working cycle has finished, the buzzer of the dishwasher will sound 3 times, then stop. Turn
off the appliance using the On/Off Button.
Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling the
Turn off the water tap,
dishes and utensils while they are still hot and more susceptible to break.
unload the baskets
They will also dry better.Unload the appliance, starting from the lower basket.
65