Whirlpool WWDH 11716S User manual

User Manual
www.whirlpool.com.sg.
ENGLISH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
ENGLISH
USER MANUAL
EN
THANK YOU FOR BUYING AN WHIRLPOOL PRODUCT.
For even more complete user support, register your
appliance at www.whirlpool.com.sg.
Index
Health and Safety guide
SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
IMPORTANT TO BE READ AND OBSERVE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
User manual
PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
APPLIANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CONTROL PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DETERGENT DISPENSER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TECHNICAL SPECIFICATIONS FOR THE WATER CONNECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
HOW TO USE THE APPLIANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
FIRST TIME USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DAILY USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
HINTS AND TIPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
PROGRAMME CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PROGRAMMES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
OPTIONS AND FUNCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CLEANING AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CLEANING THE WASHER DRYER EXTERNALLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CHECKING THE WATER INTAKE HOSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CLEANING THE FILTERS IN THE WATER INTAKE HOSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CLEANING THE DETERGENT DISPENSER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CLEANING THE WATER FILTER / DRAINING THE RESIDUAL WATER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3
TRANSPORT AND HANDLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
CUSTOMER SUPPORT SERVICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
INSTALLATION GUIDES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4
Health & Safety guide
SAFETY INSTRUCTIONS
Before using the appliance, read these safety
instructions. Keep them nearby for future reference.
These instructions and the appliance itself provide
important safety warnings, to be observed at all
times. The manufacturer declines any liability for
failure to observe these safety instructions, for
inappropriate use of the appliance or incorrect
setting of controls.
Very young children (0-3 years) should be
kept away from the appliance. Young children
(3-8 years) should be kept away from the
appliance unless continuously supervised.
Children from 8 years old and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience and
knowledge can use this appliance only if they
are supervised or have been given instructions
on safe use and understand the hazards
involved. Children must not play with the
appliance. Cleaning and user maintenance must
not be carried out by children without
supervision. Never open the door forcibly or use
it as a step.
PERMITTED USE
CAUTION: The appliance is not intended to
be operated by means of an external switching
device, such as a timer, or separate remote
controlled system.
This appliance is intended to be used in
household and similar applications such as: staff
kitchen areas in shops, offices and other
working environments; farm houses; by clients
in hotels, motels, bed & breakfast and other
residential environments.
Do not load the machine above the
maximum capacity (kg of dry cloth) indicated in
the programme table.
This appliance is not for professional use. Do
not use the appliance outdoors.
Do not use any solvents (e.g. turpentine,
benzene), detergents containing solvents,
scouring powder, glass or general purpose
cleaners, or flammable fluids; do not machine
wash fabrics that have been treated with
solvents or flammable liquids.
Do not dry unwashed items in the tumble
dryer.
Items that have been soiled with substances
such as cooking oil, acetone, alcohol, petrol,
kerosene, spot removers, turpentine, waxes and
wax removers should be washed in hot water
with an extra amount of detergent before being
dried in the tumble dryer.
EN
IMPORTANT TO BE READ AND OBSERVE
Items such as foam rubber (latex foam),
shower caps, waterproof textiles, rubber backed
articles and clothes or pillows fitted with foam
rubber pads should not be dried in the tumble
dryer.
Fabric softeners, or similar products, should
be used as specified by the fabric softener
instructions.
The final part of a tumble dryer cycle occurs
without heat (cool down cycle) to ensure that
the items are left at a temperature that ensures
that the items will not be damaged.
Never stop a tumble dryer before the end of
the drying cycle unless all items are quickly
removed and spread out so that the heat is
dissipated.
During the drying phase, the door tends to
get quite hot.
Do not use the appliance to dry clothes that
have been washed with flammable solvents
(e.g. trichlorethylene).
Do not use the appliance to dry foam rubber
or similar elastomers.
Make sure that the water tap is turned on
during the drying cycles.
Remove all objects from pockets such as
lighters and matches.
INSTALLATION
The appliance must be handled and installed
by two or more persons - risk of injury. Use
protective gloves to unpack and install - risk of
cuts.
If you want to stack a dryer on top of your
washing machine, first contact our After-Sales
Service or your specialist dealer to verify
whether this is possible. This is only possible if
the dryer is attached to the washing machine by
means of appropriate stacking kit available
through our After- Sales Service or your
specialist dealer.
Move the appliance without lifting it by the
worktop or top lid.
Installation, including water supply (if any)
and electrical connections and repairs must be
carried out by a qualified technician. Do not
repair or replace any part of the appliance
unless specifically stated in the user manual.
Keep children away from the installation site.
After unpacking the appliance, make sure that it
has not been damaged during transport. In the
event of problems, contact the dealer or your
nearest After-sales Service. Once installed,
packaging waste (plastic, styrofoam parts etc.)
5
Health & Safety guide
must be stored out of reach of children - risk of
suffocation. The appliance must be disconnected
from the power supply before any installation
operation - risk of electric shock. During installation,
make sure the appliance does not damage the
power cable - risk of fire or electric shock. Only
activate the appliance when the installation has
been completed.
Do not install your appliance where it may be
exposed to extreme conditions, such as: poor
ventilation, temperatures below 5 °C or above 35 °C.
When installing the appliance make sure that
the four feet are stable and resting on the floor,
adjusting them as required, and check that the
appliance is perfectly to level using a spirit level.
If the appliance is being installed on wood or
“floating” floors (certain parquet and laminate
materials), secure a 60 x 60 x 3 cm (at least)
sheet of plywood to the floor then place the
appliance on top of this.
Connect the water inlet hose(s) to the water
supply in accordance with the regulations of
your local water company.
For cold fill only models: do not connect to
the hot water supply.
For models with hot fill: the hot water inlet
temperature must not exceed 60 °C.
The washing machine is fitted with transport
bolts to prevent any possible damage to the
interior during transport. Before using the
machine, it is imperative that the transport bolts
are removed. After their removal, cover the
openings with the 4 enclosed plastic caps.
After installation of the device, wait a few
hours before starting it so that it acclimates to
the environmental conditions of the room.
Make sure that the ventilation openings in
the base of your washing machine (if available
on your model) are not obstructed by a carpet
or other material.
Use only new hoses to connect the appliance
to the water supply. The old hose-sets should
not be reused.
The supply water pressure must be in the
0.1-1 Mpa range.
6
ELECTRICAL WARNINGS
It must be possible to disconnect the
appliance from the power supply by
unplugging it if plug is accessible, or by a multipole switch installed upstream of the socket in
accordance with the wiring rules and the
appliance must be earthed in conformity with
national electrical safety standards.
Do not use extension leads, multiple sockets
or adapters. The electrical components must
not be accessible to the user after installation.
Do not use the appliance when you are wet or
barefoot. Do not operate this appliance if it has
a damaged power cable or plug, if it is not
working properly, or if it has been damaged or
dropped.
If the supply cord is damaged, it must be
replaced with an identical one by the
manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard risk of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is
switched off and disconnected from the power
supply before performing any maintenance
operation; never use steam cleaning
equipment - risk of electric shock.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the
recycle symbol .
The various parts of the packaging must therefore be disposed of
responsibly and in full compliance with local authority regulations
governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable
materials. Dispose of it in accordance with local waste disposal
regulations. For further information on the treatment, recovery
and recycling of household electrical appliances, contact your local
authority, the collection service for household waste or the store
where you purchased the appliance. This appliance is marked in
compliance with European Directive 2012/19/EU, Waste Electrical
and Electronic Equipment (WEEE). By ensuring this product is
disposed of correctly, you will help prevent negative consequences
for the environment and human health.
The symbol on the product or on the accompanying
documentation indicates that it should not be treated as domestic
waste but must be taken to an appropriate collection center for the
recycling of electrical and electronic equipment.
EN
User manual
PRODUCT DESCRIPTION
APPLIANCE
1.
2.
3.
4.
5.
6.
1. Top
2. Detergent dispenser
3. Control Panel
4. Lid handle
5. Door
6. Water filter - behind kick panel
7. Removable kick panel
8. Adjustable feet (2)
7.
8.
CONTROL PANEL
1.
2.
3.
13.
11.
12.
40°
h.
60°
4.
5.
6.
7.
8.
9.
10.
1. On/Off button
2. Programme selector
3. Key Lock button
4. Drying settings button
5. Dry Only Button
6. Temperature button
7. Spin button
8. Delay timer button
9. Rapid button
10. Intensive Rinse button
11. FreshCare+ button
12. Display
13. Start/Pause button
7
DETERGENT DISPENSER
Prewash Compartment
• Detergent for prewash
Main Wash Compartment
• Detergent for the main wash
• Stain remover
• Water softener
Softener compartment
• Softener
• Liquid starch
Pour softener or starch solution into
the compartment without exceeding
the “max” level.
Release button
(press to remove tray for cleaning).
B
A
Preferably use the partition A when
washing with a liquid detergent for
washing, to ensure that the correct
quantity of detergent is used (the
partition is included in the bag containing
the instructions).
Move the partition into slot B when using
detergent powder.
8
TECHNICAL SPECIFICATIONS FOR THE WATER
CONNECTION
INPUT WATER
Cold
WATER TAP
Threaded attachment for 3/4" flexible hose
MINIMUM WATER INTAKE PRESSURE
100 kPa (1 bar)
MAXIMUM WATER INTAKE PRESSURE
1000 kPa (10 bar)
EN
DOOR
To open the door, pull the handle.
To close the door, push on the handle until it clicks.
9
HOW TO USE THE
APPLIANCE
FIRST TIME USE
See the section DAILY USE for instructions on selecting
and starting a programme.
The first time the machine is switched on, you will
be asked to select the language and the display will
automatically show the language selection menu.
To select the desired language press the and h.
buttons; to confirm the selection press the button.
To change the language switch off the machine and press
buttons
, , simultaneously until an alarm is heard:
the language-selection menu will be displayed again.
To change the display luminosity, which by default
is set to the medium value, switch the machine off
then simultaneously press buttons
,
and
until the buzzer sounds. Press buttons and h. to
choose the desired level of luminosity then confirm
by pressing button .
First cycle operation
Remove any manufacturing debris:
1.Select the programme with a temperature setting
of 60 °C.
2. Pour a small quantity of detergent
powder into the main wash compartment
of the detergent dispenser (maximum 1/3
of the quantity the detergent manufacturer
recommends for lightly soiled laundry).
3. Start the programme without loading
the washer dryer machine (with empty
drum).
DAILY USE
For more information on functions, a more
detailed guide may be requested or downloaded
from the website following the instructions given
on the last page. WWW
1. LOADING LAUNDRY.
•Prepare the laundry, following the
recommendations given in the section
“HINTS AND TIPS”. - Open the door
and load the laundry into the drum,
without exceeding the maximum load
capacities indicated in the Programme Chart.
•Close the door, pressing until the latch
audibly locks, and check that
there is no laundry trapped
between the door glass and the
rubber seal.
2. OPEN THE WATER TAP
Check that the washer dryer is
connected correctly to the water mains.
Open the water tap.
10
3. SWITCHING ON THE WASHER DRYER
MACHINE.
Press button
; the lamp
flashes slowly.
4. SELECTING A PROGRAMME AND
CUSTOMISING A CYCLE. The following
functions are possible with this appliance:
•Wash only
•Wash and dry
•Dry only
Wash only
Select the required programme with the
PROGRAMME selector dial. The display will
show the name and duration of the cycle. The
washer dryer machine automatically displays
the maximum temperature and spin speed
settings possible for the selected programme.
Adjust the temperature and/or spin speed
settings if needed with the relative buttons.
•Press button to cycle through progressively
lower temperature settings until cold wash is
set (“- -“) shown on display.
•Press button to cycle through progressively
lower spin speed settings until the spin
cycle is turned off (“- -“ shown on display).
Pressing the button again sets the highest
possible setting.
Select the required options (if necessary).
•Press the button to select the option; the
respective button lamp illuminates.
•Press the button again to cancel the option; the
lamp extinguishes.
! If the selected option is not compatible with the
programme set, an error warning tone sounds
and the wording “No Selection” is shown on the
display. The option is not selected.
Wash and dry
To wash and dry a load with no interruption
between the wash and dry cycles, make sure
that the load does not exceed the maximum
permissible drying load for the selected
programme (see the column “Max. load for drying
cycle” in the Programme chart).
1. Follow the instructions given in the
paragraph “Wash Only” to select and, if
necessary, customise the required programme.
2. Press to select the required drying mode.
Two drying modes are available: automatic or timer.
- Automatic drying with selectable levels:
In automatic drying mode, the washer dryer
machine dries the laundry until the set level
of dryness is reached. Pressing button once
automatically selects the highest drying level
available for the selected programme. Press the
button again to reduce the drying level.
The following levels are available:
Cupboard extra dry
: suitable for garments
which need to be dried completely, such as
sponges and bathrobes.
Cupboard dry : laundry is completely dry and ready
to be put away in the wardrobe without ironing.
Hanger dry : laundry is left slightly damp to
minimise creasing. Garments must be hung to
air dry completely.
Iron dry : garments are left reasonably damp
to make ironing easier.
- Timer drying mode:
Press button repeatedly to set timer drying
mode. After cycling through all the automatic
drying levels, continue pressing button until
the desired time is displayed. Values from 180
to 30 minutes are settable.
To wash a load of laundry larger than the
maximum permissible load for drying (see
the column “Max. load for drying cycle” in the
Programme chart), remove a few garments once
the washing cycle has finished before starting
the drying cycle. Proceed as follows:
1.Follow the instructions given in the paragraph
“Wash Only” to select and, if necessary,
customise the required programme.
2. Do not include a drying cycle.
3. Once the washing cycle is finished, open the
door and remove a few garments to reduce the
load. Now follow the instructions for “Dry only”.
N.B.: always allow a cooling down period after
drying before opening the door.
EN
When using the two preset cycles
and
, it is not necessary to select and start a drying cycle.
Dry only
This function is used to simply dry a wet load
washed previously in the washer dryer or by hand.
1.Select a suitable programme for the laundry
you want to dry (e.g. select cotton to dry wet
cotton laundry).
2.Press button to dry without a wash cycle.
3.Press to select the required drying mode. Two
drying modes are available: automatic drying by
levels or drying by time.
- Automatic drying with selectable levels:
In automatic drying mode, the washer dryer
machine dries the laundry until the set level of
dryness is reached. Pressing button once
automatically selects the highest drying level
available for the selected programme. Press the
button again to reduce the drying level.
The following levels are available:
Cupboard extra dry
: suitable for garments
which need to be dried completely, such as
sponges and bathrobes.
Cupboard dry : laundry is completely dry and ready
to be put away in the wardrobe without ironing.
Hanger dry : laundry is left slightly damp to
minimise creasing. Garments must be hung to
air dry completely.
Iron dry : garments are left reasonably damp
to make ironing easier.
- Timer drying mode:
Press button repeatedly to set timer drying
mode. After cycling through all the automatic
drying levels, continue pressing button until
the desired time is displayed.
Values from 180 to 30 minutes are settable.
N.B.: always allow a cooling down period after
drying before opening the door.
5. USING THE CORRECT AMOUNT OF
DETERGENT. Pull out the tray and pour detergent
into the relative compartments as described in
“Detergent dispenser”. This is only necessary when
using a wash only or a wash + dry programme.
6. DELAYING THE START OF A PROGRAMME. To
set a programme to start at a later time, see the
section “Options and Functions”.
7. STARTING A PROGRAMME.
Press the START/PAUSE button. The relative
indicator lamp illuminates, the door locks
and the door open symbol extinguishes.
To change a programme while a cycle is in
progress, press START/PAUSE to pause the
washer dryer (the START/ PAUSE lamp flashes
amber slowly); then select the required cycle
and press START/PAUSE again. To open the door
while a cycle is in progress, press START/PAUSE;
the door may be opened if the symbol lights.
Press the START/PAUSE button again to resume
the programme from where it was paused.
11
8. CANCELLING A RUNNING PROGRAMME (IF
NECESSARY)
Press and hold the button until the washer
dryer stops.
If the water level and temperature are low
enough, the door unlocks and may be opened.
The door remains locked if there is water in the
drum. To unlock the door, switch the washer
dryer on, select the
programme and turn the spin function off
by setting the spin speed to “- -“. The water is
emptied and the door unlocks at the end of the
programme.
9. SWITCHING THE WASHER DRYER OFF AT THE
END OF A PROGRAMME.
At the end of the cycle, the message “Cycle end”
is shown on the display. The door can only be
opened when the symbol lights. Check that
the door unlocked symbol is lit, then open the
door and take out the laundry.
Press to switch the washer dryer off. To save
energy, if the washer dryer is not switched
off manually with the
button, it turns off
automatically approximately 30 minutes after
the end of the programme.
Leave the door ajar to let the interior of the
washer dryer dry.
HINTS AND TIPS
RULES FOR SEPARATING LAUNDRY
• Fabric type / indications on label (cotton, mixed
fibres, synthetic, wool, handwash items)
• Colour (separate coloured garments from
whites, wash new coloured items separately)
• Size (wash items of different sizes in the same
load to improve washing efficacy and weight
distribution in the drum)
• Delicates (place small items – such as nylon stockings
– and garments with clasps – such as braziers – in a
laundry bag or in a pillow case with a zip).
EMPTY POCKETS
• Objects such as coins or safety pins can damage
laundry and the washer dryer drum.
WASH SYMBOLS
ON GARMENT LABELS
The value given in the tub symbol is the maximum
temperature possible for washing the garment.
Normal mechanical action
Reduced mechanical action
Much reduced
mechanical action
Hand wash only
Do not wash
12
CLEAN THE WATER FILTER REGULARLY
• This is needed to prevent the filter from blocking
and preventing the water from draining correctly.
See the section “Cleaning and Maintenance” /
“Cleaning the water filter” in the detailed guide
that may be requested or downloaded from the
website. WWW
SAVING ENERGY AND PROTECTING THE
ENVIRONMENT
• Keeping within the load limits indicated in the
programme chart will optimise energy, water
and detergent consumption and reduce washing
times.
• Do not exceed the detergent quantities
recommended by the detergent manufacturer.
• Save energy by using a 60°C instead of a 90°C
wash programme, or by using a 40°C instead of a
60°C wash programme. We recommend using the
60°C programme for cotton garments, which
is longer but uses less energy.
• To save energy and time when washing and
drying, select highest spin speed available for
the programme to reduce the residual water
remaining in the garments at the end of the wash
cycle.
EN
PROGRAMME CHART
COTTON (2)
- 60°C
1600
11
7
-
SYNTHETICS
- 60°C
1200
5
5
-
- 40°C
800
5
5
- 30°C
--
1
1
- 40°C
800
2,5
2,5
- 60°C
1600
11
7
- 90°C
1600
11
7
JEANS
DELICATES
WOOL
ECO COTTON (1)
WHITES
SPIN + DRAIN *
-
1600
11
7
RINSE + SPIN
-
1600
11
7
4,5
4,5
-
-
-
-
Prewash
-
-
(90°)
SPORT
- 40°C
600
DUVET
- 30°C
1000
-
3,5
-
RAPID 30’
- 30°C
800
-
4
-
COLOURS 15°
15°C
1000
5,5
5,5
-
WASH & DRY 45’
30°C
1600
1
1
-
WASH & DRY 90’
30°C
1200
2
2
-
Selectable/optional
-
Not selectable/applicable
Liquid
-
Softener
5,5
Main
5,5
Recommended
detergent
Powder
Duration (Minutes)
Max . load for drying cycle (kg)
1000
Drying
- 40°C
Max . spin speed
(rpm)
MIXED
Programme
The duration of the programme is shown on the display .
Max . load for wash
cycle (kg)
Available temperatures
Detergents and additives
-
Required quantity
Optional quantity
For wash programmes with temperatures above 50°C, we recommend using powder detergent rather than liquid, and following the directions given on the
detergent package.
* Select the
programme and set the spin speed to “-
-“ to empty only.
1) Test programme in compliance with standard EN 50229 (Wash): select the
2) Long cotton programme: set the
programme with a temperature of 40°C.
Test programme in compliance with standard EN 50229 (Drying): select the
drying cycle must be carried out with the nominal load.
programme with a temperature of 60°C.
wash programme and set the drying level to “
”, for both loads. The first
The cycle duration indicated on the display or in the manual is an estimated time calculated for standard conditions. The actual cycle time may vary in relation to a
number of different factors, such as inlet water temperature and pressure, ambient temperature, quantity of detergent, size and type of load, load balancing and any
additional optional functions selected.
13
PROGRAMMES
Follow the directions indicated in the garment
wash symbols.
MIXED
for washing lightly to normally soiled resilient
garments in cotton, linen, synthetic fibres and mixed
fibres.
DUVET
designed for washing eiderdown padded items such
as double or single duvets, cushions and anoraks.
It is recommended to load such padded items in
the drum with the edges folded inwards and not
to exceed ¾ of the drum’s volume. For optimal
washing, we recommend using a liquid detergent.
COTTON
for washing normally to heavily soiled towels,
underwear, table and bed linen etc. in resilient cotton
and linen.
RAPID 30’
for washing lightly soiled garments quickly: this
cycle lasts only 30 minutes, saving time and energy.
Maximum load 4 Kg.
SYNTHETICS
for washing normally soiled garments made from
synthetic fibres (such as polyester, polyacrylic, viscose
etc.) or cotton/synthetic blends.
COLOURS 15°
This cycle helps protect colours by washing in cold
water (15°C) and uses less energy to heat the water
while still offering satisfactory wash results. Suitable
for lightly soiled, ustained garments. This cycle offers
wash results comparable to 40°c mixed at just 15°C.
JEANS
Turn garments inside-out before washing and use a
liquid detergent.
DELICATES
for washing particularly delicate garments. Preferably
turn garments inside out before washing.
WASH & DRY 45’
for washing and drying lightly soiled cotton and
synthetic fibre garments quickly. This cycle washes
and dries a laundry load of up to 1 Kg in just 45
minutes.
WOOL
All wool garments can be washed using programme
‚“Wool“ even those carryng the “hand-wash only “
label. For best results, use special detergents and do
WASH & DRY 90’
for washing and drying cotton and synthetic fibre
garments quickly. This cycle washes and dries a
laundry load of up to 2 Kg in just 90 minutes.
not exceed max kg declaration of laundry.
ECO COTTON
for washing normally soiled cotton garments.
At 40°C and 60°C, this is the standard cotton
programme and the most efficient and terms of
water and energy consumption.
WHITES
For washing normally to heavily soiled towels,
underwear, table and bed linen, etc in resilient cotton
and linen. Only when the temperature is selected at
90°C the cycle is provided with a prewash phase before
main washing phase. In this case it is recommended
to add detergent both, in the prewash and main wash
section.
SPIN + DRAIN
spins the load then empties the water. For resilient
garments.
RINSE + SPIN
rinses and then spins. For resilient garments.
SPORT
for washing lightly soiled sports clothing (tracksuits,
shorts, etc.); for best results, we recommend not
exceeding the maximum load indicated in the
“Programme chart”. We recommend using liquid
detergent, and adding the amount suitable for a
half-load.
14
EN
OPTIONS AND FUNCTIONS
OPTIONS selectable directly by pressing the
relative button
! If the selected option is not compatible with the
programme set, an error warning tone sounds
and the wording “No Selection” is shown on the
display. The option is not selected.
FRESHCARE+
If associated with wash cycles, this option
increases their performances by generating
steam to block proliferation of the main sources
of unpleasant odours inside the appliance
(exclusively for the wash). After the steam
phase, the machine runs a delicate cycle with
slow drum rotations. When the FRESHCARE+
option is associated with drying cycles, it
prevents stubborn creases from stabilising on
garments, thanks to slow drum rotations.
The FreshCare+ cycle starts at the end of the
wash or drying cycle and continues for
maximum 6 hours; it can be interrupted at any
time by pressing any button on the control
panel, or by turning the knob. Wait roughly 5
minutes before opening the door.
INTENSIVE RINSE
Option makes it possible to select the desired
rinse type for sensitive skin. Press the button
once for the “Extra +1” level, which makes it
possible to select an additional rinse after the
standard cycle rinse and remove all traces of
detergent. Press the button again for the “Extra
+2” level, which makes it possible to select two
additional rinses to the standard cycle rinses;
it is recommended for very sensitive skin.
When the button is pressed for the third time,
the “Extra +3” level is set, thus allowing the
selection of 3 rinses in addition to the standard
cycle’s rinses. The option - started with cycles
at a temperature of 40°C - makes it possible
to remove major allergens such as pollen, cat
and dog hair. With cycles at a temperature
higher than 40° a very good level of antiallergic
protection is achieved. Press the button again
to go back to the “Normal rinse” rinse type.
If the current adjustment can be neither set nor
changed, the display will show “No Selection”
or “No Change”.
RAPID
If you select this option , the wash duration will
be reduced by up to 50% depending on the
selected cycle, thereby guaranteeing
simultaneos water and energy saving. Use this
cycle for lightly soiled garments.
h.
DELAY TIMER
To set the selected programme to start at a
later time, press the button to set the desired
delay time. To cancel the delayed start, press
the button again until the value “-- h” is shown
on the display.
LOCK BUTTON
to lock the control panel, press and hold the
button
for approximately 2 seconds. When
the display visualises “KEY LOCK ON” the
control panel is locked (with the exception of
the button). This prevents unintentional
changes to programmes, especially with
children near the machine.
To unlock the control panel, press and hold the
button
for approximately 2 seconds.
15
CLEANING AND MAINTENANCE
WARNING
Never use flammable liquids to clean the washer
dryer.
Be sure to turn off the washer dryer and
disconnect it from its electrical power supply
before performing any cleaning or maintenance
operations.
CLEANING THE WASHER DRYER EXTERNALLY
Clean the washer dryer's external parts using a soft
damp cloth.
16
Do not use generic detergents, glass detergents,
abrasive powders, or other similar products to
clean the control panel, as these could damage the
printed elements.
CHECKING THE WATER INTAKE HOSE
EN
Periodically check the integrity of the water
intake hose. If it is found to be damaged, contact
Customer Support or an authorised dealer in order
to obtain a replacement hose.
Based on the type of hose:
If the water intake hose has a transparent cover,
periodically check to make sure that there are no
areas where the colour is more pronounced.In such
cases, the hose may have a leak and may need to
be replaced.
For flood protection hoses: check the safety valve's
inspection window (see the arrow). If it's red, this
means that the flood protection function has
been engaged; in this case, the hose will have to
be replaced with a new one. In order to detach
the hose, press the release button (if present) and
unscrew the hose.
17
CLEANING THE FILTERS IN THE WATER INTAKE HOSE
1. Close the water tap and unscrew the intake
hose.
1
2
2. Thoroughly clean the mesh filter at the end of
4. Re-insert the mesh filter. Reconnect the intake
hose to the water tap and the washer dryer. Do
not use tools to connect the intake hose. Open
the water tap and check to make sure that all the
connections have been tightened properly.
the hose using a brush.
3. At this point, manually unscrew the intake hose
from the back of the washer dryer. Using pliers,
extract the mesh filter from the valve on the back
of the washer dryer and clean it.
2
1
18
CLEANING THE DETERGENT DISPENSER
EN
1. Remove the detergent dispenser by pressing 4. Dry with a soft cloth.
the release button and pulling on the dispenser at
the same time.
1
2
5. Re-install the detergent dispenser and close it.
2. Remove the insert from the fabric softener
compartment.
3. Wash the components under running water,
taking care to remove all the detergent and fabric
softener residues.
19
CLEANING THE WATER FILTER /
DRAINING THE RESIDUAL WATER
WARNING
Make sure that the washer dryer has been shut
off and disconnected from its electrical power
supply before cleaning the water filter or draining
the residual water.If a high temperature wash
1. Remove the kick panel: Using a screwdriver,
do that which is shown in the following figure.
programme has recently been used, wait for the
water to cool before draining it.
The water filter should be cleaned regularly in
order to prevent water from remaining inside
the appliance after wash cycles due to filter
obstructions.
3. Drain the water:
Slowly turn the filter counter-clockwise until all the
water has come out. Allow the water to flow out
without removing the filter.
Once the container is full, close the water filter by
turning it clockwise. Empty the container. Repeat
the procedure until all the water has been drained.
2. Container for the drained water:
Place a low and wide container under the water
filter in order to collect the residual water.
4. Remove the filter: Place a cotton cloth under
the water filter in order to absorb any small
amounts of residual water. Next, remove the water
filter by turning it counter-clockwise.
20
5. Clean the water filter: remove any residues
EN
from the filter and wash it under running water.
6. Insert the water filter and reinstall the kick
panel: Re-insert the water filter by turning it
clockwise. Turn it as far as it will go; the filter's grip
should be in its vertical position. In order to check
the filter's seal, pour about 1 litre of water into the
detergent dispenser.
Re-install the kick panel.
2
1
21
TRANSPORT AND HANDLING
WARNING
Do not lift the washer dryer while holding onto its
upper surface.
1. Disconnect the electrical plug and close the
water tap.
2. Check to make sure that the door and the
detergent dispenser are securely closed.
3. Disconnect the intake hose from the water
tap, then disconnect the drain hose. Eliminate all
the residual water from the hoses, and secure them
in such a way that they will not be damaged during
the transport operations.
4. Reapply the transport bolts. Follow the
procedure for removing the transport bolts
described in the Installation Instructions, in the
opposite order.
Important: never transport the washer dryer
without having applied the transport bolts.
22
EN
TROUBLESHOOTING
The washer dryer may sometimes not work properly for certain reasons. Before calling the Support
Centre, it is recommended to check to see if the problem can be easily resolved using the following list.
Anomalies:
Possible causes / Solution:
The washer dryer does not
turn on.
•
•
•
T he plug is not inserted into the electrical outlet, or not
enough to make contact.
There has been a power failure.
The door is not fully closed.
The wash cycle does not start.
•
•
•
•
T he ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap is not open.
A start delay has been set.
The washer dryer does not fill
with water (the message “NO
WATER, Turn tap on” is shown
on the display).
•
•
•
•
•
T he water intake hose is not connected to the tap.
The hose is bent.
The water tap is not open.
The mains water supply has been shut off.
There is not enough pressure.
The washer dryer loads and
drains water continuously.
•
•
T he START/PAUSE button has not been pressed.
The drain hose has not been installed at 65 to 100 cm from
the ground.
The end of the drain hose is immersed in water.
The drain connector on the wall does not have an air vent.
If the problem persists after having performed these
checks, close the water tap, shut off the washer dryer, and
call the Support Centre.If the dwelling is located on one
of the uppermost floors of a building, a siphon effect can
sometimes occur, thus causing the washer dryer to load
and drain water continuously.Special anti-siphon valves are
available on the market to prevent these types of problems.
•
•
The washer dryer does not
drain or does not spin.
•
The washer dryer vibrates
excessively during the spin
cycle.
•
•
•
t the time of installation, the drum was not properly
A
unlocked.
The washer dryer is not level.
The washer dryer is squeezed between furniture and the wall.
The washer dryer leaks water.
•
•
•
T he water intake hose has not been tightened properly.
The detergent dispenser is clogged.
The drain hose has not been properly fastened.
The machine is locked and the
display flashes, indicating an
error code (e.g. F-01, F-..).
•
•
•
T he programme does not include the draining function: with
certain programmes it must be activated manually.
The drain hose is bent.
The drain line is obstructed.
S hut off the machine, disconnect the plug from the outlet,
and weight about 1 minute before turning it back on.
If the problem persists, call the Support Centre.
23
Too much foam is formed.
•The detergent is not compatible with the washer dryer (it
must bear the wording “for washing machines”, “ for hand
washing and washing machines”, or something similar).
•
The dosage was excessive.
The washer dryer does not dry.
•
•
•
•
•
24
The plug is not inserted into the electrical outlet.
There has been a power failure.
The door is not fully closed
A start delay has been set.
The DRY function is set to its 0 position.
EN
CUSTOMER SUPPORT SERVICE
BEFORE CONTACTING
CUSTOMER SUPPORT
1. Try to resolve any problems you may encounter
on your own by consulting the section titled.
TROUBLESHOOTING
2.
Shut off the washer dryer and turn it back on
to see if the problem persists.
IF THE PROBLEM PERSISTS,
CONTACT CUSTOMER SUPPORT
Call the number shown on the warranty booklet,
or follow the instructions provided at the
website www.whirlpool.com.sg.
Always provide:
A brief description of the problem.
The washer dryer model (see the data plate inside
the door).
Your address and telephone number.
For any repairs that may be required, please
contact an authorised Customer Support Centre
in order to ensure that the repairs are performed
correctly using original spare parts.
Manufacturer:
Whirlpool EMEA S.p.A. - Socio Unico
Via Carlo Pisacane n. 1
20016 Pero (MI)
Italy
25
INSTALLATION GUIDES
10 mm - 0,39 inch
3.
2.
1.
150 ml
100 ml
50 ml
4.
2 cm - 0,7 inch
6.
26
5.
7.
8.
EN
9.
max 0,5 cm
max 0,2 inch
10.
11.
12.
max 100 cm
39 inch
min 65 cm
25 inch
max 100 cm
39 inch
min 65 cm
25 inch
max 100 cm
39 inch
min 65 cm
25 inch
13.
14.
27
Whirlpool® Registered trademark/TM Trademark of Whirlpool group of companies © Copyright Whirlpool Europe s.r.l. 2014. All rights reserved - http://www.whirlpool.eu
001
28
n
11259768