Ignis AKS 236/AE Instruction for Use

AKS 236
EN
User and maintenance manual
IT
Manuale d’uso e manutenzione
IMPORTANT SAFETY INSTRUCTIONS
These instructions shall also be available on website: www.whirlpool.eu
YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT
This manual and the appliance itself provide important safety warnings, to be read and observed at all times.
This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others.
All safety warnings are preceded by the danger symbol and the following terms:
DANGER
Indicates a hazardous situation which, if not avoided, will cause serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could cause serious injury.
All safety warnings give specific details of the potential risk present and
indicate how to reduce risk of injury, damage and electric shock
resulting from improper use of the appliance. Carefully observe the
following instructions:
- Use protective gloves to perform all unpacking and installation
operations.
- The appliance must be disconnected from the power supply before
carrying out any installation work.
- Installation and maintenance must be carried out by a qualified
technician, in compliance with the manufacturer’s instructions and
local safety regulations. Do not repair or replace any part of the
appliance unless specifically stated in the user manual.
- Power cable replacement must be carried out by a qualified
electrician. Contact an authorized service centre.
- Regulations require that the appliance is earthed.
- The power cable must be long enough for connecting the
appliance, once fitted in its housing, to the main power supply.
- For installation to comply with current safety regulations, an allpole disconnect switch with minimum contact gap of 3 mm must
be utilized.
- Do not use multiple plug adaptors if the oven is fitted with a plug.
- Do not use extension leads.
- Do not pull the power supply cable.
- The electrical components must not be accessible to the user after
installation.
EN1
- If the surface of the induction plate is cracked, do not use it and
switch off the appliance to avoid the possibility of electric shock
(only for models with induction function).
- Do not touch the appliance with any wet part of the body and do
not operate it when barefoot.
- This appliance is designed solely for use as a domestic appliance for
cooking food. No other type of use is permitted (e.g.: heating
rooms). The Manufacturer declines all responsibility for
inappropriate use or incorrect setting of the controls.
- The appliance and its accessible parts become hot during use. Care
should be taken to avoid touching heating elements. Very young
(0-3 years) and young children (3-8 years) shall be kept away unless
continuously supervised.
- Children from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and
knowledge can use this appliance only if they are supervised or
have been given instructions on safe appliance use and if they
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by
children without supervision.
- During and after use, do not touch the heating elements or interior
surfaces of the appliance - risk of burns. Do not allow the appliance
to come into contact with cloths or other flammable materials until
all the components have cooled down completely.
- At the end of cooking, exercise caution when opening the
appliance door, letting the hot air or steam exit gradually before
accessing the oven. When the appliance door is shut, hot air is
vented from the aperture above the control panel. Do not obstruct
the vent apertures.
- Use oven gloves to remove pans and accessories, taking care not to
touch the heating elements.
- Do not place flammable materials in or near the appliance: a fire
may break out if the appliance is inadvertently switched on.
- Do not heat or cook sealed jars or containers in the appliance.
The pressure that builds up inside might cause the jar to explode,
damaging the appliance.
EN2
- Do not use containers made of synthetic materials.
- Overheated oils and fats catch fire easily. Always remain vigilant
when cooking foods rich in fat and oil.
- Never leave the appliance unattended during food drying.
- If alcoholic beverages are used when cooking foods (e.g. rum,
cognac, wine), remember that alcohol evaporates at high
temperatures. As a result, there is a risk that vapours released by the
alcohol may catch fire upon coming into contact with the electrical
heating element.
- Never use steam cleaning equipment.
- Do not touch the oven during the pyrolysis cycle. Keep children
away from the oven during the pyrolysis cycle. Excess spillage must
be removed from the oven cavity before cleaning cycle (only for
ovens with Pyrolysis function).
- Only use the temperature probe recommended for this oven.
- Do not use harsh abrasive cleaners or sharp metal scrapers to clean
the oven door glass since they can scratch the surface, which may
result in shattering of the glass.
- Ensure that the appliance is switched off before replacing the lamp
to avoid the possibility of electric shock.
Do not use aluminium foil to cover food in the cooking vessel
(only for ovens with cooking vessel supplied).
Scrapping of household appliances
-
This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal
regulations. Before scrapping, cut off the power supply cable.
For further information on the treatment, recovery and recycling of household electrical appliances, contact your
competent local authority, the collection service for household waste or the store where you purchased the appliance.
INSTALLATION
After unpacking the oven, make sure that it has not been damaged during transport and that the oven door closes properly. In
the event of problems, contact the dealer or your nearest After-sales Service. To prevent any damage, only remove the oven
from its polystyrene foam base at the time of installation.
PREPARING THE HOUSING UNIT
•
•
•
•
Kitchen units in contact with the oven must be heat resistant (min 90°C).
Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all wood chips and sawdust.
After installation, the bottom of the oven must no longer be accessible.
For correct appliance operation, do not obstruct the minimum gap between the worktop and the upper edge of the oven.
ELECTRICAL CONNECTION
Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The dataplate is on the front
edge of the oven (visible when the door is open).
•
Power cable replacement (type H05 RR-F 3 x 1.5 mm2) must be carried out by a qualified electrician. Contact an
authorized service centre.
EN3
GENERAL RECOMMENDATIONS
Before use:
-
Remove cardboard protection pieces, protective film and adhesive labels from accessories.
Remove the accessories from the oven and heat it at 200° for about an hour to eliminate the smell and fumes from the
insulating materials and protective grease.
During use:
-
Do not place heavy objects on the door as they could damage it.
Do not cling to the door or hang anything from the handle.
Do not cover the inside of the oven with aluminium foil.
Never pour water into the inside of a hot oven; this could damage the enamel coating.
Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.
Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become trapped in the door.
Do not expose the oven to atmospheric agents.
SAFEGUARDING THE ENVIRONMENT
Disposal of packing material
The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of the packing must
therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.
Scrapping the product
-
This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment
(WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
The symbol
on the product or on the accompanying documentation indicates that it should not be treated as
domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic
equipment.
Energy saving
-
Only pre-heat the oven if specified in the cooking table or your recipe.
Use dark lacquered or enamelled baking moulds as they absorb heat far better.
Switch the oven off 10/15 minutes before the set cooking time. Food requiring prolonged cooking will continue to cook even
once the oven is switched off.
DECLARATION OF CONFORMITY
-
This oven, which is intended to come into contact with foodstuffs, complies with European Regulation ( ) n.1935/2004
and has been designed, manufactured and sold in conformity with the safety requirements of the “Low Voltage” directive
2006/95/CE (which replaces 73/23/CEE and subsequent amendments), the protection requirements of “EMC” 2004/108/
CE.
TROUBLESHOOTING GUIDE
The oven does not work:
•
•
Check for the presence of mains electrical power and if the oven is connected to the electrical supply.
Turn off the oven and restart it to see if the fault persists.
EN4
AFTER-SALES SERVICE
Before calling the After-Sales Service:
1.
See if you can solve the problem yourself with the help of the suggestions given in the “Troubleshooting guide“.
2.
Switch the appliance off and back on again it to see if the fault persists.
If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.
Always specify:
•
a brief description of the fault;
•
the type and exact model of the oven;
•
the service number (number after the word Service on the rating plate), located on the right hand edge of the oven cavity
(visible when the oven door is open). The service number is also indicated on the guarantee booklet;
•
your full address;
•
your telephone number.
If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used
and repairs carried out correctly).
CLEANING
WARNING
-
Never use steam cleaning equipment.
Only clean the oven when it is cool to the touch.
Disconnect the appliance from the power supply.
Oven exterior
IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with
the appliance, clean immediately with a damp microfibre cloth.
•
Clean the surfaces with a damp microfibre cloth. If it is very dirty, add a few drops of washing up detergent to the water.
Finish off with a dry cloth.
Oven interior
IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin enamelled surfaces
and the oven door glass.
•
After every use, allow the oven to cool then clean it preferably while it is still warm in order to remove built-up dirt and
stains caused by food residues (e.g. food with a high sugar content).
•
Use proprietary oven detergents and follow the manufacturer’s instructions to the letter.
•
Clean the door glass with a suitable liquid detergent. The oven door can be removed to facilitate cleaning (see
MAINTENANCE).
•
The top heating element of the grill (see MAINTENANCE) can be lowered (some models only) to clean the roof of the oven.
N.B.: during prolonged cooking of foods with a high water content (e.g. pizza, vegetables, etc.) condensation may form
on the inside of the door and around the seal. When the oven is cold, dry the inside of the door with a cloth or sponge.
Accessories:
•
•
Soak the accessories in water with washing up detergent immediately after use, handling them with oven gloves if still
hot.
Food residues can be easily removed using a brush or sponge.
Cleaning the rear wall and catalytic side panels of the oven (if present):
IMPORTANT: do not use corrosive or abrasive detergents, coarse brushes, pot scourers or oven sprays which could
damage the catalytic surface and ruin its self-cleaning properties.
•
Operate the oven empty with the fan-assisted function at 200°C for about one hour
•
Next, leave the appliance to cool down before removing any food residue with a sponge.
EN5
MAINTENANCE
-
WARNING
Use protective gloves.
Ensure the oven is cold before carrying out the following operations.
Disconnect the appliance from the power supply.
REMOVING THE DOOR
To remove the door:
1.
2.
3.
Open the door fully.
Lift the catches and push them forwards as far as they will go (Fig. 1).
Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (Fig. 2).
To refit the door:
1.
2.
3.
4.
Fig. 1
Insert the hinges in their seats.
Open the door fully.
Lower the two catches.
Close the door.
Fig. 2
MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)
1.
2.
3.
Fig. 3
Remove the side accessory holder grilles (Fig. 3).
Pull the heating element out a little (Fig. 4) and lower it (Fig. 5).
To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to rest on the lateral
supports.
Fig. 4
Fig. 5
EN6
REPLACING THE OVEN LAMP
To replace the rear lamp (if present):
1.
Disconnect the oven from the power supply.
2.
Unscrew the lamp cover (Fig. 6), replace the lamp (see note for lamp type) and screw the lamp cover back on.
3.
Reconnect the oven to the power supply.
To replace the side lamp (if present):
1.
Disconnect the oven from the power supply.
2.
Remove the side accessory holder grilles, if present (Fig. 3).
3.
Use a screwdriver to prise off the lamp cover (Fig. 7).
4.
Replace the lamp (see note for lamp type) (Fig. 8).
5.
Reposition the lamp cover, pushing it on firmly until it snaps into place (Fig. 9).
6.
Refit the side accessory holder grilles.
7.
Reconnect the oven to the power supply.
Fig. 6
Fig. 7
Fig. 8
Fig. 9
N.B.:
Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230 V type G9, T300°C halogen lamps.
The lamp used in the appliance is specifically designed for electrical appliances and is not suitable for household room
illumination (Commission Regulation (EC) No 244/2009).
Lamps are available from our After-sales Service.
IMPORTANT:
If using halogen lamps, do not handle with bare hands since fingerprints can damage them.
Do not use the oven until the lamp cover has been repositioned.
EN7
INSTRUCTIONS FOR OVEN USE
FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION
1.
Control panel
2.
Upper heating element/grill
3.
Cooling fan (not visible)
4.
Dataplate (not to be removed)
5.
Lamp
6.
Fan
7.
Turnspit (if present)
8.
Lower heating element (not visible)
9.
Door
10. Position of shelves (the number of shelves is indicated on the front of the oven)
11. Rear wall
N.B.:
During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.
At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a while.
ACCESSORIES SUPPLIED
Fig. A
Fig. B
A.
WIRE SHELF: the wire shelf can be used to grill food or as a support for pans, cake tins and other ovenproof cooking
receptacles.
B. DRIP TRAY: the drip tray is designed to be positioned under the wire shelf in order to collect fat or as an oven tray for
cooking meat, fish, vegetables, focaccia, etc.
The number of accessories may vary according to which model is purchased.
ACCESSORIES NOT SUPPLIED
Other accessories can be purchased separately from the After-sales Service.
EN8
INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN
1.
2.
Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).
The other accessories, like the drip tray and baking tray, are inserted with the raised part on the flat section “B” facing
upwards (Fig. 2).
Fig. 1
Fig. 2
CONTROL PANEL DESCRIPTION
1
1.
2.
3.
4.
2
3
4
Function selector knob
Analog clock
Thermostat knob
Thermostat led
OVEN OPERATION (also see analog clock paragraph)
•
Turn the selector knob to the required function.
The oven light switches on.
•
Turn the thermostat knob clockwise to the required temperature.
The thermostat led lights up, switching off again when the oven reaches the selected temperature.
At the end of cooking, turn the knobs to “0”.
ANALOG CLOCK
The analog clock allows:
1.
Viewing the time of the day. To adjust the time of the day, press the button (B) and turn it anticlockwise
to set the time.
2.
Programming the cooking start time. The maximum programmed cooking start time is 12 hours.
Programming the cooking time. Select the cooking time (available with any function) to turn the oven on for
a specified period of time. At the end of the specified time the oven will switch off automatically. The
minimum programmed cooking time is 5 minutes and the maximum programmed cooking time is
180 minutes.
A. MANUAL COOKING
1.
Turn the button (B) anticlockwise (without pressing), until the symbol is displayed in the window .
2.
Press the button (A) and turn it anticlockwise until the triangle (D) points to the time shown on the clock (hour hand).
The button clicks when turned to the proper position.
3.
Turn the selector knob to the required symbol. The oven light switches on.
4.
Turn the thermostat knob clockwise to the required temperature. The red thermostat indicator light switches on.
5.
At the end of cooking, turn the knobs to OFF (0 - •) because in manual mode the oven will NOT switch off automatically.
F.
MANUAL COOKING WITH COOKING START TIME
1.
Turn the button (B) anticlockwise (without pressing), until the symbol is displayed in the window .
2.
Press the button (A) and turn it anticlockwise until the triangle (D) points to the time at which cooking is to start (e.g. in
figure: 11:30).
3.
Turn the selector knob to the required symbol.
4.
Turn the thermostat knob clockwise to the required temperature.
5.
At the end of cooking, turn the knobs to OFF (0 - •) because in manual mode the oven will NOT switch off automatically.
F.
PROGRAMMED COOKING WITH COOKING START TIME AND COOKING DURATION
1.
Turn the button (B) anticlockwise (without pressing) until the required cooking duration is displayed in the window (C)
(5 - 180 min.).
2.
Press the button (A) and turn it anticlockwise until the triangle (D) points to the time at which cooking is to start (e.g. in
figure: 11:30).
3.
Turn the selector knob to the required symbol.
4.
Turn the thermostat knob clockwise to the required temperature.
EN9
5.
At the end of the set cooking time an acoustic signal will sound and the oven will switch off automatically. To exclude
the acoustic signal, turn button (B) anticlockwise (without pressing) until the symbol
is displayed in the window.
6.
At the end of the set cooking time, cooking may be prolonged by following the instructions given above, or by
using the manual cooking procedure.
G. PROGRAMMED COOKING WITH COOKING DURATION
1.
Turn the button (B) anticlockwise (without pressing) until the required cooking duration is displayed in the window (C)
(5 - 180 min.).
2.
Press the button (A) and turn it anticlockwise until the triangle (D) points to the time shown on the clock (hour hand).
The button clicks when turned to the proper position.
3.
Turn the selector knob to the required symbol. The oven light switches on.
4.
Turn the thermostat knob clockwise to the required temperature. The red thermostat indicator light switches on.
5.
At the end of the set cooking time an acoustic signal will sound and the oven will switch off automatically. To exclude
the acoustic signal, turn button (B) anticlockwise (without pressing) until the symbol
is displayed in the window.
At the end of the set cooking time, cooking may be prolonged by following the instructions given above, or by using the
manual cooking procedure.
EN10
OVEN FUNCTION DESCRIPTION TABLE
FUNCTIONS KNOB
OFF
LAMP
CONVENTIONAL
To stop cooking and switch off the oven.
To switch the oven light on/off.
To cook any kind of dish on one shelf only. Use the 2nd shelf. Preheat the oven to the required
temperature. The thermostat led turns off when the oven is ready and food can be placed in it.
CONVECTION BAKE
For baking cakes with liquid filling (sweet or savoury) on a single shelf. This function can also be
used for cooking on two shelves. Switch the position of the dishes to cook food more evenly. Use
the 2nd shelf to cook on one shelf only, and the 2nd and 4th to cook on two shelves. Preheat the
oven before cooking.
GRILL
To grill steak, kebabs and sausages; to cook vegetables au gratin and toast bread. Place food on
the 4th shelf. When grilling meat, use the drip tray to collect the cooking juices. Position it on the
3rd shelf, adding approx. half a litre of water. Preheat the oven for 3-5 min. During cooking the
oven door must remain closed.
TURBO GRILL
To roast large joints of meat (legs, roast beef, chickens). Position the food on the middle shelves.
Use the drip tray to collect the cooking juices. Position it on the 1st/2nd shelf, adding approx. half
a litre of water. It is advisable to turn the meat over during cooking for more even browning. The
oven does not have to be preheated. During cooking the oven door must remain closed.
DEFROST
To speed up defrosting of food. Place food on the middle shelf. Leave food in its packaging in
order to prevent it from drying out on the outside.
EN11
COOKING TABLE
Recipe
Function
Pre- Shelf (from Temp.
heating bottom)
(°C)
Yes
2
Leavened cakes
Filled pies (cheesecake, strudel, apple
pie)
Yes
2-4
Yes
2
Yes
2-4
Yes
2
Biscuits / Tartlets
Yes
2-4
Yes
2
Choux buns
Yes
2-4
Yes
2
150-175 35-90 Cake tin on wire shelf
Shelf 4: cake tin on wire shelf
(switch levels halfway through
150-170 30-90 cooking)
Shelf 2: cake tin on wire shelf
Drip tray/baking tray or cake tin
150-190 30-85
on wire shelf
Shelf 4: cake tin on wire shelf
(switch levels halfway through
150-190 35-90 cooking)
Shelf 2: cake tin on wire shelf
160-175 20-45 Drip tray / baking tray
Shelf 4: wire shelf (switch levels
160-170 20-45 halfway through cooking)
Shelf 2: drip tray / baking tray
175-200 30-40 Drip tray / baking tray
Shelf 4: oven tray on wire shelf
(switch levels halfway through
170-190 35-45 cooking)
Shelf 2: drip tray / baking tray
100
110-150 Drip tray / baking tray
100
Shelf 4: oven tray on wire shelf
(switch levels halfway through
130-150 cooking)
Shelf 2: drip tray / baking tray
Meringues
Bread / Pizza /
Focaccia
Yes
2-4
Yes
2
Yes
2-4
Yes
2
Yes
2-4
Yes
2
Frozen pizza
Savoury pies (vegetable pie, quiche)
Yes
2-4
EN12
Time Accessories and notes
(min)
225-250 12-50 Drip tray / baking tray
Shelf 4: oven tray on wire shelf
(switch levels halfway through
225-250 20-45 cooking)
Shelf 2: drip tray / baking tray
Drip tray / baking tray or wire
250
10-15
shelf
Shelf 4: oven tray on wire shelf
(switch levels halfway through
250
10-20 cooking)
Shelf 2: drip tray / baking tray
175-200 45-55 Cake tin on wire shelf
Shelf 4: cake tin on wire shelf
(switch levels halfway through
175-190 45-60 cooking)
Shelf 2: cake tin on wire shelf
Recipe
Function
Pre- Shelf (from Temp.
heating bottom)
(°C)
Yes
Vols-au-vent / Puff
pastry crackers
Lasagne / Baked
pasta / Cannelloni /
Flans
Lamb / Veal / Beef /
Pork 1 Kg
Chicken / Rabbit /
Duck 1 Kg
Turkey / Goose 3 Kg
Baked fish / en papillote (fillet, whole)
Stuffed vegetables
(tomatoes, courgettes, aubergines)
Toast
2
Yes
2-4
Yes
2
Yes
2
Yes
2
Yes
1/2
Yes
2
Yes
2
Yes
4
175-200 20-30 Drip tray / baking tray
Shelf 4: oven tray on wire shelf
(switch levels halfway through
175-200 20-40 cooking)
Shelf 2: drip tray / baking tray
200
45-65
80-110
175-200 50-60 Oven tray on wire shelf
200
Yes
4
200
Sausages / Kebabs /
Spare ribs / Hamburgers
Yes
4
200
-
2
200
2-5
Roast Beef rare 1 Kg
-
2
200
Leg of lamb /
Shanks
-
2
200
Roast potatoes
-
2
200
Vegetable gratin
-
2
200
Wire shelf
Shelf 4: wire shelf (turn food
20-30 halfway through cooking)
Shelf 3: drip tray with water
Shelf 4: wire shelf (turn food
30-40 halfway through cooking)
Shelf 3: drip tray with water
Shelf 2: wire shelf (turn food
two thirds of the way through
55-70 cooking if necessary)
Shelf 1: drip tray with water
60-80
EN13
Drip tray or oven tray on wire
shelf
Drip tray or oven tray on wire
shelf
Drip tray or oven tray on wire
200
50-100
shelf
Drip tray or oven tray on wire
200
80-130
shelf
Drip tray or oven tray on wire
175-200 40-60
shelf
200
Fish fillets / steaks
Roast chicken
1-1.3 Kg
Time Accessories and notes
(min)
Shelf 2: turnspit (if present)
Shelf 1: drip tray with water
Oven tray on wire shelf (turn
35-45 food two thirds of the way
through cooking if necessary)
Drip tray or oven tray on wire
shelf (turn food two thirds of
60-90
the way through cooking if
necessary)
Drip-tray / baking tray (if
45-55 necessary, turn food two thirds
of the way through cooking)
20-30 Oven tray on wire shelf
Recipe
Function
Pre- Shelf (from Temp.
heating bottom)
(°C)
Lasagna & Meat
Yes
2-4
200
Meat & Potatoes
Yes
2-4
200
Fish & Vegetables
Yes
2-4
175
EN14
Time Accessories and notes
(min)
Shelf 4: oven tray on wire shelf
(switch levels two thirds of the
way through cooking if
50-100
necessary)
Shelf 2: drip tray or oven tray on
wire shelf
Shelf 4: oven tray on wire shelf
(switch levels two thirds of the
way through cooking if
45-100
necessary)
Shelf 2: drip tray or oven tray on
wire shelf
Shelf 4: oven tray on wire shelf
(switch levels halfway through
30-50 cooking)
Shelf 2: drip tray or oven tray on
wire shelf
RECOMMENDED USE AND TIPS
How to read the cooking table
The table indicates the best function to use for any given food, to be cooked on one or more shelves at the same time. Cooking
times start from the moment food is placed in the oven, excluding pre-heating (where required). Cooking temperatures and
times are purely for guidance and will depend on the amount of food and type of accessory used. Use the lowest recommended
values to begin with and, if the food is not cooked enough, then move on to higher values. Use the accessories supplied and
preferably dark coloured metal cake tins and oven trays. You can also use pans and accessories in pyrex or stoneware, but bear
in mind that cooking times will be slightly longer. To obtain best results, carefully follow the advice given in the cooking table
for the choice of accessories (supplied) to be placed on the various shelves.
Cooking different foods at the same time
Using the “CONVECTION BAKE” function, you can cook different foods which require the same cooking temperature at the same
time (for example: fish and vegetables), using different shelves. Remove the food which requires less cooking time and leave
food which requires longer cooking time in the oven.
Desserts
-
-
Cook delicate desserts with the conventional function on one shelf only. Use dark coloured metal cake tins and always
position them on the wire shelf supplied. To cook on more than one shelf, select the forced air function and stagger the
position of the cake tins on the shelves, aiding optimum circulation of the hot air.
To check whether a raising cake is cooked, insert a wooden toothpick into the centre of the cake. If the toothpick comes
out clean, the cake is ready.
If using non-stick cake tins, do not butter the edges as the cake may not rise evenly around the edges.
If the cake “sinks” during cooking, set a lower temperature the next time, perhaps reducing the amount of liquid in the
mixture and mixing more gently.
For sweets with moist fillings (cheesecake or fruit pies) use the “CONVECTION BAKE” function. If the base of the cake is
soggy, lower the shelf and sprinkle the bottom of the cake with breadcrumbs or biscuit crumbs before adding the filling.
Meat
-
Use any kind of oven tray or pyrex dish suited to the size of the piece of meat being cooked. For roast joints, it is best to
add some stock to the bottom of the pan, basting the meat during cooking for added flavour. When the roast is ready, let
it rest in the oven for another 10-15 minutes, or wrap it in aluminium foil.
When you want to grill meat, choose cuts with an even thickness all over in order to achieve uniform cooking results. Very
thick pieces of meat require longer cooking times. To prevent the meat from burning on the outside, lower the position of
the wire shelf, keeping the food farther away from the grill. Turn the meat two thirds of the way through cooking.
To collect the cooking juices it is advisable to place a drip-tray with half a litre of water directly under the grill on which the meat
is placed. Top-up when necessary.
Turnspit (only in some models)
Use this accessory to evenly roast large pieces of meat and poultry. Place the meat on the turnspit rod, tying it with string if
chicken, and check that it is secure before inserting the rod in the seat located on the front wall of the oven and resting it on the
respective support. To prevent smoke and to collect cooking juices, it is advisable to place a drip-tray with half a litre of water on
the first level. The rod has a plastic handle which must be removed before starting to cook, and used at the end of cooking to
avoid burns when taking the food out of the oven.
Pizza
Lightly grease the trays to ensure the pizza has a crispy base. Scatter the mozzarella over the pizza two thirds of the way through
cooking.
EN15
5019 550 00372
GB
IT
Whirlpool is a registered trademark of Whirlpool, USA
Printed in Italy
06/2011
">