Electrolux EHS620X User Manual

Ceramic Glass Hob
Operating Instructions
EHS 620 X
IB 319 5060-00
PM-D 2000.03.30
31% £20 Pay
Please read these instructions carefully for using your
new appliance. Pay special attention to the chapter
“Hints on safety”.
Keep these instructions in a safe place for future refe-
rence and pass them on to any subsequent owner of
the appliance.
The warning triangle and/or specific words (war-
ning, caution, important) are used to highlight in-
formation that is important for your safety or the
functioning of the appliance.
i) After this symbol you will find supplementary
information on operating and practical use of the
appliance.
v Tips and instructions for the economical and en-
blé vironmentally sound use of the appliance are
marked with this symbol.
These instructions contain informations on how to rec-
tify faults yourself. See the section "What to do if … “
Should you require further assistance, please contact
your local Service Force Centre.
Content
For the user
Dear Customer!
Safety information
Disposal
of packaging material
Hints of disposal
Before the first use
Cleaning for the first time
Description of the hob
Digital indicators
Special features of the appliance
Operating instructions
General information
TOUCH-CONTROL-sensorfields
Switchin on the appliance
Switching off the appliance
Cooking zone selection
Setting selection
Dual cooking zione
Cooking zone switch-off
Residual heat indicator
Child safety device
Safety cut-off after time
Safety cut-off due to a spillage
Application, charts, tips
Cooking and frying utensils
General hints
Energyconsumption
Chart: boiling and frying
Cleaning and care
Ceramic glass surface
Light soilage
Stubborn soilage
Special soilage
Sugar
Dark spots and decor damages
Scratches in the ceramic glass surface
The hob frame
What to do ...
Guarantee conditions, Customer care
CO Oooo J Oo haa LE N
For the installer
Installation instructions
Hints on safety
Buit-in in the kichen-worktop
Electrical connection
Technical data, rating plate
18
18
18
20
21
EEE
e
Sh
wre ver
FERAL
The safety of this appliance corresponds to the
acknowledged rules of technique and to the law on
appliance safety. The safety measures existing as a
matter of self-understanding would, however, not cover
all of possible risks of accidents.
Moreover, we feel compelled as the manufacturer to
make you familiar with the following hints on safety.
Electrical safety
e This appliance must be installed by qualified
personnel.
e Repairs to the appliance should only be carreid
out by authorised service enginneers. improper
repairs can lead to injury or serious malfunction.
If your appliance need repairing please contact
your local Service Force Centre,
El Piease observe this instruction, otherwise the
guarantee will not cover any damage that may
occur.
e Built-in appliances must be installed in built-in
cupboards and worktops. The cupboards have to
be located and fastened in a way that they are sta-
ble. The protection against accidental contact re-
quired by the VDE will then be ensured.
e Damaged appliances must not be installed.
e Do not use the hob if the ceramic glass is dama-
ged:
- switch off the cooking zones,
- disconnect from the electricity supply.
e A special electronically controlled safety-switch-
off makes sure that all cooking zones are swit-
ched off automatically after a defined time, incase
there will be no variation of settings.
Safety for children
e This appliance is designed to be operated by
adults only. Do not allow children to play with the
product or tamper with the controls.
e This hob is fitted with a safety device of the elec-
tronic control which prevents playing children
from turning the hob.
Safety during use
e This hob is intended for domestic cooking only. It
is not designed for commercial or industrial
purposes.
e The appliance gets hot when in use. In case of ca-
reless handling there is danger of burning one-
self at the heating zones.
e Do not use the cooking zones to heat the room.
4
e Take care when plugging electrical items into
mains sockets near the hob. Connecting leads
must not come into connection with the hot
surface or vessels.
e Hot oils can ignite very quickly. Do not leave the
hob unattended when preparing foods in pans of
oil, i.e. frying chips.
e The sensor technique provides best-possible sa-
fety with the manipulation of the appliance, but to
the same extent it needs care when setting coo-
king zones, output or periods of time.
e After use make sure that the appliance Is
switched off,
Safety when cleaning
e Ensure that all heating zones are switched off
while cleaning the hob.
e For safety reasons do not clean the appliance with
a steam jet or high pressure cleaner.
How to avoid damaging your appliance
e Do not use the hob surface as a working surface
or for storage.
e Do not use the cooking zones with empty pans or
without pans. This could cause damage to the
pans or the hob.
e (Ceramic glass is insensitive to temperature shock
and very robust, however, it is not unbreakabie.
Hard and sharp objects, in particular, can damage
the cooking surface if they fall on it.
e Do not use cast iron pots or pans with damaged
bases that are rough or burred. Scratching may
occur when the lids are slid.
® Do not place any pans on the hob frame. Scrat-
ching may occur or the paint damaged.
e Ensure that liquids containing acids, e.g. vinegar,
lemon limescale removing agents do not come
into contact with the hob frame, otherwise matt
spots will appear.
e |f sugar or adish containing sugar comes into con-
tact with a hot cooking zone and then melts, re-
move the soiling immediately whilst still warm,
using a glass scraper. If it cools, damage to the
surface may occur.
e Keep all items and materials that melt away from
the ceramic glass surface, e.g. plastics, alumi-
nium foil or oven foils. If something of this nature
should melt onto the ceramic glass surface, it
must be removed immediately using a glass scra-
per.
Disposal of packaging material
v All parts of the packaging can be recycled and
Wid hard foam parts are appropriately marked.
PE = Polyethylene
(outer wrapping and the bag inside)
PS = Polystyrene foam (eg. packing pieces)
Please dispose of all packaing and old
appliances with due regard for safety and the
environment.
i) Please observe the national and regional regula-
tions on appliances and packing material as well
as the material marking (material separation,
refuse collection, waste disposal sites).
Hints on disposal
v The appliance must not be disposed of with the
wid household rubbish.
Please contact your local council or
Environmental Health Office to see if there are
facilities in your area to recycle the appliance.
Cleaning for the first time
The hob has to be cleaned thouroughly before it is first
used.
e Wash the ceramic glass surface and the frame
with warm water with a little washing up liquid ad-
ded and wipe dry.
A Never use aggressive or abrasive cleaning
agents, they may damage the ceramic glass and
hob frame.
я >
Cooking zone-———— {| 100-180 mm || Dual cooking zone
À | 600-1700 W
Cooking zone - Cooking zone
DO
© a
| © SE ©
N— |
Control section
Switching -on second circuit
Heat Setting selection
Cooking zone selector
rear left
front left
Digital indicators
Four display fields, one for each cooking zones show up as follows:
when selecting a cooking zone,
depending on heat setting selected,
with residual heat,
with malfunction,
with child safety device switcned on.
Control lamp dual cooking zone
Main switch ON/OFF
Cooking zone selector
rear right
front right
after switch-on and with automatic switch off by the safety function,
Ceramic glass cooking area:
The appliance is comprised of a ceramic glass
cooking surface and 4 quick-heating cooking zo-
nes. Due to especially efficient radiant heating
elements the cooking zones will heat up very
quickly.
Touch controls:
The appliance is controlled by TOUCH-CON-
TROL.
Touch control ON/OFF:
With use of the ON/OFF touch controls the power
supply to the appliance can be switched on and
off.
Control and function indicators:
Digital indicators or control lamp provide informa-
tion about settings made L]/5), functions activa-
ted (1)/-] as well as any residual heat [H] of the
corresponding cooking zone.
Warm-keeping setting:
[4 = this setting allows you to keep dishes warm.
Dual cooking zone:
The appliance is fitted with a dual cooking zone
©. This means you may use this cooking zone in
two sizes, for smaller and larger pots. A chance
for saving energy.
Residual heat indicator:
A E (“hot”) for residual heat indication will come
on in the display in case of a cooking zone tempe-
rature that implies the danger of burning.
Safety lock / children safety device:
With this function [L] the cooking area can be se-
cured against unintended switching-on.
Safety cut-off:
A safety cut-off makes sure that all cooking zones
will be switched off automatically after some time
if there is no variation of settings.
Cleaning:
Due to the ceramic glass cooking area and the
touch controls being a single unit, it is very easy
to keep the hob clean.
General information
The cooking surface is made of proven ceramic glass.
and consists of 4 cooking zones. The rapid glowing
cooking zones with that the especially efficient radiant
heating elements will considerably reduce the duration
of heating-up.
El The cooking surface is pore-free and also insen-
sitive to rapid changes in temperature. Pots can
therefore be moved from a hot to cold zone.
En When switching on a cooking zone you may hear
a short buzz. Thatis a characteristic of all ceramic
glass cooking zones and does not impair the func-
tion or the lifetime of the appliance.
Always put pots and pans onto the cooking zone
before switching on.
TOUCH-CONTROL sensor fields
e Tooperate the TOUCH-CONTROL sensor fields
put your finger flat from top onto the desired field,
until corresponding indicators will come on or go
out, respectively unt the desired function will be
carried out.
Switching on the appliance
The entire appliance is switched on by means of the
touch control (I) ON/OFF.
e Keep the control ON/OFF touched for about two
seconds.
The digital indicators show [-] and the digital point
flashes.
i) Once the appliance has been switched on, a coo-
king zone must be selected within 10 seconds
with use of the cooking zone selector. If a cooking
zone is not selected the appliance will switch off
for safety reasons.
Switching off the appliance
To fully switch off the appliance use the touch control
(D ON/OFF,
e Keep the sensor field ON/OFF touched for about
two seconds.
(1) After switching off of one individual cooking zone
or of the entire cooking area, the residual heat is
indicated with (A) (“hot”) in the digital indicators of
the corresponding cooking zones.
o о
a 45 E
Cooking zone selection
To activate a cooking zone keep the correspon-
ding control touched for about one second. A zero
with digital point [4] comes on in the correspon-
ding cooking zone display.
Setting selection +) - —
For selecting or changing the setting for the coo-
king zone from L) to (5).
use the [+ touch control to increase the setting.
use the (=) touch control to reduce the setting.
Dual cooking zone switch-on and ~off ©
When using the dual cooking zones the larger heating
circuit can be switched on in addition to the smaller
zone by using responding touch control © on the cera-
mic glass cooking area.
di
The outer zone can be switched on at any time du-
ring the use of the inner zone. The control lamp
iluminates after the outer zone has been switched
on.
1. Touch the control for the dual cooking zone
The outer heating circuit is switched on, the con-
trol lamp beside the touch control for the dual coo-
king zone lights up.
2. For switching off the outer heating circuit touch
the control for the dual cooking zone ©, the outer
heating circuit is switched off.
Cooking zone switch -off
1. Select the desired cooking zone by means of
the cooking zone touch control.
2. For switching off push the (+) and [=] touch con-
trols at the same time or return to zero with the >)
touch control,
a) OH
Uk) Par
a) OH
Ho 40.
Residual heat indicator
After switching off a single cooking zone or the entire
hob any residual heat is indicated by (2) (“hot”)showing
in the display of the corresponding cooking zone.
Even after switching off a cooking zone the residual
heat indicator will go out only after sufficient cooling
down of the cooking zone.
Y The residual heat can be used for the melting and
wid keeping dishes warm.
Caution! While the (1) is illuminated the hob is hot
and there is a risk of burning.
Caution! If there is a power failure the (+) will go
out even if there is residual heat in the hob. Care
will have to be taken until there is no longer a risk
of burning.
Child-safety device
Acitivating the child-safety device
The child-safety device prevents the cooking zones
being switched on accidentaily.
(3) The child-safety device can only be activated
when the hob is switched on.
e 1. Touch the (I) ON/OFF control.
e 2. Immediately after (within 10 seconds) touch the
and (=) controls at the same time for about two
seconds and then release.
e 3. Touch the +) control again. [L] will be indicated
in the digital displays for about 10 seconds. The
child-safety device is now activated.
Use of the cooking area with the child-safety devi-
ce activated
e 1. Touch the (I) ON/OFF control.
e 2. Within 10 seconds touch the +) and E) con-
trols at the same time for about two seconds.
The digital displays show [-] and the digital point
flashes.
e 3. Select the cooking zone and set the heat set-
ting as desired.
The child-safety device remains deactivated until
you next switch off the apliance. All cooking zones
and settings can be used as normal.
10
HPF) (OH
Deacitivating the child-safety device
E The child-safety device can only be deactivated
when the hob is switched off.
e 1. Touch() ON/OFF control, [UJ is indicated inthe
digital displays.
e 2 Toucht+ and[=) controls at the same time for
about 2 seconds and the release.
e 3. Touch (=) control again. Symbol [L] will go out
in the digital displays and [-] will be indicated. The
child-safety device is now deactivated.
Safety cut off after a time
If a cooking zone is not switched off or if a setting is not
varied after a defined time, the corresponding cooking
zone will switch off automatically.
appears in the cooking zone display and [-) after
cooling down.
e The cooking zones switch off as follows:
s setting1—2 after 6 hours
setting3—4 after 5 hours
‚ setting 5 after 4 hours
*» setting 6 — 9 after 1.5 hours
To re-set the cooking zones, if required, the appliance
must be switched back on using the main switch (I
ON/OFF.
Safety cut off due to a spillage
Liquids that boil over and spill onto the surface will
cause the cooking zones to switch off.
The hob will also switch itself off if a wet cloth is placed
on the control panel.
In either case the appliance must be switched back on,
once the liquid or cloth has been removed, with the
main switch CD ON/OFF for further use.
11
a
« > -v
Cooking and frying utensils
di
The better the pot or the pan, the better the boiling
or frying result.
You can recognise good quality pans by their
base. The base should be thick and as flat as pos-
sible.
Rough bases (i.e. burrs and sharp edges) will
scratch the ceramic glass surface.
Utensils with aluminium and copper bases can
leave behind metallic discolorations which can
only be removed with difficulty or sometimes not
at all.
Saucepans and frying pans should not be smaller
than the cooking zone, and preferably not more
than 10-15 mm larger than the diameter of the
cooking zone.
When cold, pan bases normally curve slightly
inwards (are concave). In no case should they
curve outwards (be convex).
When buying new pots or pans pay attention to
the base diameter. Manufacturers often state the
upper diameter of the edge of a dish.
If you are using special cooking utensils like pres-
sure cookers or a WOK, follow the manufacturer's
instructions.
Follow any guidelines provided by the saucepan
manufacturer, Ensure they are recommended for
use on ceramic hobs.
General hints
®
The bases should always be clean and dry.
To avoid scratching or damaging the ceramic
glass surface, pots and pans should be moved on
the hob by lifting them, and not by sliding.
Scratches can also be caused by grains of sand
(e.g. originating from the previous washing of
vegetables), drawn over the cooking surface with
the pan, or by burrs and the rims of pan bases.
Use high sided pans for dishes with alot of liquid,
so that nothing boils over.
Energy consumption
To save energy, you should:
place pots and pans in position before switching
on the cooking zone.
use only cooking and frying utensils with smooth,
flat bases.
12
e wherever possible, cover pots and pans with a lid.
® never place pots or pans on cooking zones with
a higher diameter.
® because of wet or dirty cooking zones and pots
energy will be wasted.
e switch off the cooking zone a few minutes before
the end of the cooking time, in order to make use
of the residual heat.
e When using pressure cookers you can reduce the
cooking time by up to 50%. As well as saving X X
energy, more vitamins and minerals are retained
in the food.
Chart:: Boiling and frying
(3) The setting position required for cooking processes is dependent on the quality of the pots and on the type
and amount of the food.
Switch position
Cooking method
Examples
9 Parboiling Starting of cooking and roasting, cooking of large quantities of
Quick frying liquid, then switch-back to appropriate setting
7-9 Frying French fries, pan-cakes
Deep fat frying Fillet of pork and beef, steaks goulash
; Frying of meat, schnitzel, cutlets, meat-balls, sausages, liver
Roastin ying , , : ges, ,
6-7 _ roasting fish-fillet in deep fat,
Frying without crust Frying eggs or chops
Boiling , . а:
4-5 ШИ Boiled potatoes, stews, soups, hot-pot, sauces in large quantities
Braising
3.4 Simmering Simmering of vegetables, braising of meat, lightly cooking
Stewing small amount of fruit with little liquid
Simmering of rice and food with milk (sometimes stirring),
2-3 Gentle simmering Stewing of smaller amount of potatoes or vegetables,
Warming up of prepared meal
, Omelette, fried eggs, Hollandaise sauce,
Keeping warm |
1-2 Melti Keeping warm a meal or small amount of hot-pot
119 Melting of butter, chocolate, gelatine.
0 Residual heat
Residual heat, OFF -position
El When heating up or frying, we recommend heat setting “9”, and then continue cooking foods at an appropriate
lower heat setting.
13
A
Attention! Cleaners must not get onto the hot ce-
ramic glass surface! After cleaning all residues of
cleaners must be removed with sufficient clean
water, as they may be caustic when being rehea-
ted.
Never use aggressive or abrasive agents, such
as oven sprays, stain or rust removers, scouring
powder, or sponges with an abrasive effect.
Suitable cleaning materials are: clean cloth or
household paper, hot water with detergent, suita-
ble commercial cleaners and cleaning scrapers.
Cleaning scrapers and ceramic glass cleaners
are available from the expert trade and in markets
for building material.
Ceramic glass surface
Clean the ceramic glass surface after every use
.
when it is hand warm or cold. This will avoid spills
becoming burnt on.
e Remove scale and water marks, fat spots and
metailic shimmering discoloration with a commer-
cial ceramic glass cleaner such as Vitrocien.
Light soilage
e Wipethe ceramic glass surface with a damp cloth,
and a little washing up liquid.
e Then rub dry with a clean cloth. No residues of
cleaner must be left on the surface.
e Once a week, throroughly clean the entire cera-
mic glass surface with a commercial ceramic
glass cleaner such as “Vitroclen”. Always ensure
that the hob is dry after cleaning.
Stubborn soilage
To remove food that has boiled over or burnt on
spots, use a glass scraper.
Place the glass scraper at an angle to the ceramic
glass surface. Remove soiling by sliding the scra-
per.
14
о a
Q 4P a
Special soilage
Sugar
e Remove burnt-on sugar, melted plastics, alumi-
num foil immedeiately - when they are still warm
- using a glass scraper, otherwise damage may
be caused.
A Warning! When using the cleaning scraper on the
warm cooking zone care should be taken.
e Afterwards clean the cooking surface normally.
(i) If the cooking zone and melted material has coo-
led down, reheat the cocking zone gently to aid
the cleaning process.
Dark spots, decor damages
(3) If aggressive cleaners or pans with abrasive ba-
ses are used, then the decor will take on an abra-
ded appearence and dark spots will appear over
time.
These marks cannot be removed. However, they
do impair the fuctionability of the hob.
Scratches in the ceramic glass surface
El Scratches in the ceramic glass surface resulting
from burrs on a pan base or sand grains cannot
be removed.
However, they do impair the fuction of the hob.
The hob frame
A Do not allow vinegar, lemons or scale removers to
come into contact with the hob frame, matt spots
will appear.
e Clean the hob frame with water and a little was-
hing up liquid.
e Soften dried dirt with a wet cloth. Then wipe off
and rub dry.
15
BEE
If the hob does not function correctly, please carry out
the following checks, as it may be something you can
remedy yourself.
… if the cooking zones will not function?
Check, whether
the main fuse has failed.
the appliance is correctly switched on.
the safety cut off has operated.
the control lamps of the control panel are lighting.
the corresponding cooking zone is switched on.
the cooking zones are set for cooking as desired.
if cooking zones cannot be switched on/off?
Check, whether
e the control panel is locked.
e a period of more than 10 seconds has elapsed
between pressing the on/off switch and selecting
a cooking zone.
e thetouchcontrois are entirely or partly covered by
liquid or by a wet cloth.
.-. Tf the whole indicator section for residual heat,
except (+), will fail all of a sudden?
Check, whether
e the ON/OFF touch control (I) was accidentally
touched.
e thetouch controls are entirely or partly covered by
liquid or by a wet cloth.
e the safety cut off has operated.
® there was a power cut for a short while.
. if the displays suddenly go out?
Check, whether
e the fuse has failed.
e there has been a power cut.
e the setting operation was correctly made.
… if after cooking zone switch-off the display will
not show LJ or (E) for residual heat?
Check, whether
e the cooking zone has only been in operation for a
short while, and is therefore not hot enough.
... if a cooking zone cannot be switched on?
Check, whether
e the child-safety [L] is switched on.
. if all displays (inclusive of residual heat indica-
tor [)) go out during cooking?
16
e The overheating protection of the electronic con-
trols has blocked the use of the hob. Once the
cooking zone has cooled down it can be operated
again.
... if the display (F] flashes?
1) If the hob has been used at a high setting for a
long period of time, the overheating protection of
the electronic control will become active and the
front left cooking zone will become inoperable.
This occurs to prevent damage to the electronic
controls. The front left cooking zone will operate
again once the appliance has cooled down and
is no longer in the display. The front right and rear
cooking zones can still be operated during this
time.
... if the display (E) lights up?
Check, whether
e thetouch controls are entirely or partly covered or
contaminated by liquid or by a wet cloth.
e Clean the ceramic glass surface and wipe it dry.
e If after switching the appliance back on, the dis-
play still shows (Е). Contact your local Service
Force Centre.
If after carrying out the above checks your appliance is
still faulty, disconnect from the mains supply and con-
tact your local Service Force Centre.
In guarantee customers should ensure that the
above checks have been as the engineer will make
a chargeif the faultis nota mechanical or electrical
breakdown. |
Please note that proof of purchase is required for
any in-guarantee service calls.
Hints on safety
A
This appliance must be installed and connec-
ted by qualified personel. Please observe this
instruction, otherwise the warranty will not
cover any dmage which may occur.
During the installation and in case of a service fai-
lure the appliance must not be connected to the
mains.
The general rules for the operation of electric ap-
pliances, the provisions by the competent electri-
city supply board and the specifications of these
instructions for installation have to be strictly ad-
hered to.
Built-in in the kitchen worktop
A
Electrical safety is to be ensured by professionali
installation.
Protection against accidental contact according
to the regulations set by VDE or other local autho-
rities must be ensured by correct installation of
the appliances. The same refers to the back of the
appliance which, even in case of built-in solutions
away from the wali, must not be freely accessible.
Built-in cupboards have to be located and faste-
ned in a way that they are stable.
Note down the data from the rating plate of your
appliance in the printed rating plate form in this
manual. These numbers are needed in case of
service calls.
Installation dimensions
The opening in the cabinet must correspond to the
standard dimensions. The necessary information can
be found in the dimensional sketch.
The separation between the lower surface of the
hob and the parts of the furniture below it must be
at least 20 mm
The lateral separation between the sides of the
hob and the cabinet must be at least 55 mm, and
must be at least 55 mm from the rear panel.
17
distance from worktop
opening to the rear wall
distance from worktop opening to
the left or right side wall or to a
high cupboard
A 50 mm
El With regard to the protection against overheating
of surrounding furniture surfaces this appliance
corresponds to type Y. This appliance or the built-
in cupboard for the appliance respectively may be
located with the rear wall and one side wall towha-
tever high walls or furniture respectively and with
the other side to another appliance or furniture of
the same height as this appliance.
Hob installation
e Cut out the worktop with the cut-out size as sta-
ted. The toleranced sizes must not be exceeded.
Saw exactly at the marking line. Recommenda-
tion: Mark the cut-out with a steel needle.Cover-
glue the line in order to avoid splintering of the
coating when cutting.
e Clean the worktop in the cut-out section
e With tiled worktops the grooves within the contact
area of the cooking area must completely be filled
up with groove material.
e Then fasten the catch springs with screws in the
cut-out at the marked position. The distortion of
the springs serves as a stop on the worktop.
e With natural, artificial stone, or ceramic plates the
springs can be glued in with special adhesive
(synthetic resin, two-component adhesive, etc.)
e The cooking area is entered from the top into the
cut-out section, centered and firmly pressed on
until the springs will catch.
e Check the seal in the supporting frame for perfect
seating and gapless support. Please do not apply
further silicone sealing matter as this will compli-
cate the removal of the hob if servicing is neces-
sary.
i frame
seating — mic glass plate
worktop
snap-in clamp
18
Electrical connections
A Before connecting the appliance, check that the
voltage quoted on the rating plate - that is, the no-
minal voltage of the appliance - corresponds to
the available mains voltage. The rating plate can
be found on the lower housing of the ceramic
glass hob.
e The mains connection must be carried out by an
expert electrician. The VDE-regulations and the
valid prescriptions by the local power suppy
boards have to be compiled with.
e Prior to connection it should be checked whether
the voltage stated on the rating plate - ¡.e. the
nominal voltage of the appliance and of the oven/
control box - is identical with the prevailing mains
voltage. The rating plate is located on the lower
housing of the hob.
e The heating element voltage amounts to 230 V ~.
The appliance will also perfectly perform with the
former mains voltage of 220 V ~.
e The mains connection must be carried out in a
way that an all-pole insulating device is existing
with a contact opening of at least 3 mm, e.g. LS-
automatism, earth-leakage circuit-breaker or
fuse.
e Awire of type HOSVV-F or of higher rating is to be
used as supply cable.
® The mains terminal is located in the bottom of the
appliance behind a covering slide. It can be ope-
ned with a screw driver {pict.).
e According to existing mains voltage the appliance
has to be connected in correspondence with the
diagrams of connecting possibilities. The bridges
of the terminal board are to be changed accordin-
gly, if need be.
e The protective conductor is to be connected to
terminal ©. The protective conductor must be
longer than live leads.
e The cable connections have to be connected
as shown and the terminal screws be firmly
tightened.
.
Afterwards the supply cable has to be secured by
strain relief device and the covering slide must be
closed by firmly pressing down until it engages.
A Prior to first use remove any existing labels and
protective film from the ceramic glass plate or the
frame of the hob.
After connecting the electrical supply, all cooking
zones should be briefly switched on one after the
other at their maximum power, in order to test
whether they are operational.
19
Mains terminal
in the base of the hob
changing brid-
ges of the ter-
Connecting possibilities
©
(@__ bauibivetard —_ WN
Gq n-geib / green- yellow
verde-amarillo
PED
(7
2 N~ 230 V ~
Anschiussleitung Mulde| Elekirischer Anschluss Anschiusslaitung Mulde| Elektrischer Anschluss
connecting line hob | electrical connection | =— | connecting line hob | electrical connection
conexión artesa conexión eléctrica + conexión artesa conexión elácirica
a
(1) schwarz { black negro y 4 „| D) Schwarz / black / negro
- Li
(2) schwarz black / negro _ L2 (2) _schwarz / black / negro 7”
330
©
@ blau { blue | azul N
© grun-gelb / graen- yellow
© verde - amarillo PE S
„
Specifications, Standards, Guidelines
572 mm This appliance corresponds to the following standards:
502 mm e EN B60 335-1 and EN 60 335-2-6
49 mm with regard to the safety of electric appliances for
491 domestic use and similar purposes
e DIN 44546 / 44547 / 44548
with regard to the criteria for electric cookers for
560 mm domestic use.
490 mm e EN 55014-2/ VDE 0875 part 14-2
В5
e EN 55014 / VDE 0875 part 14 / 12.93
Power of cooking zones: e EN 61000-3-2/ VDE 0838 part 2
. e EN 61000-3-3 / VDE 0838 part 3
Cooking zone front left ............... 2300 W with regard to the basic protection demands for
Cooking zonerearleft................ 1200 W lectr ti tibilitv (EMC
Cooking zone rear right ........... 600-1700 W electromagnetic compatibility ( )
Cooking zone front right .............. 1200 W
Total connected load max. ......... 6,4 kW CE This appliance corresponds to EC-guidelines
Voltage .......—._eeeeeevednano 230 V -50 Hz e 78/23/EC dí. 19.02.1973
(low-voltage-guideline)
e 89/336/EC dt. 03.05.1989
(EMC-guideline inclusive of
amendment-guideline 92/31/EC)
( >
Note down here the data from the rating plate of your appliance. The rating plate is on the base of the hob.
The rating plate is not visible after the hob has been built-in.
This information wilt be required:
- when requesting a service call
- when ordering spare parts or accessories
- with technical queries.
© Electrolux MADE IN GERMANY
| TYP: PEE2 019 PNC: 949 590 807 MODELL: EHS 620X |
230 V - FNL,
Total max. 6,4 kW q CE &
N J
20
">