Juno-Electrolux JHD68210I User Manual
Add to my manuals
20 Pages
Electrolux JHD68210I is a 60 cm wide induction hob with four cooking zones. It has a power function that can increase the power of a cooking zone to 3200W, making it ideal for boiling water or searing meat. The hob also has a Keep Warm function that keeps food warm at a low temperature, and a child lock to prevent accidental activation. The hob is easy to use, with touch controls and a clear display. It also has a residual heat indicator to warn you if the hob is still hot after it has been turned off.
advertisement
▼
Scroll to page 2
of 20
user manual Ceramic glass induction hob JHD68210I 2 electrolux Electrolux. Thinking of you. Share more of our thinking at www.electrolux.com Contents Safety Information Description of the appliance Operating the appliance Tips on cooking and frying Cleaning and care 2 3 5 10 11 What to do if… Disposal Installation instructions Service 12 13 14 15 Subject to change without notice Safety Information Warning! Please comply with these instructions. If you do not, any damage resulting is not covered by the warranty. Correct use • This appliance is not intended for use by children or other persons whose physical, sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction by a responsible person to ensure that they can use the appliance safely. • Do not leave the appliance unattended during operation. • This appliance should be used only for normal domestic cooking and frying of food. • The appliance must not be used as a work surface or as a storage surface. • Additions or modifications to the appliance are not permitted. • Do not place or store flammable liquids, highly inflammable materials or fusible objects (e.g. plastic film, plastic, aluminium) on or near the appliance. Children’s safety • Small children must be kept away from the appliance. • Only let bigger children work on the appliance under supervision. • To avoid small children and pets unintentionally switching the appliance on, we recommend activation of the child safety device. General safety • The appliance may only be installed and connected by trained, registered service engineers. • Built-in appliances may only be used after they have built in to suitable built-in units and work surfaces that meet standards. • In the event of faults with the appliance or damage to the glass ceramic (cracks, scratches or splits), the appliance must be switched off and disconnected from the electrical supply, to prevent the possibility of an electric shock. • Repairs to the appliance must only be carried out by trained registered service engineers. Safety during use • Remove stickers and film from the glass ceramic. • There is the risk of burns from the appliance if used carelessly. • Cables from electrical appliances must not touch the hot surface of the appliance or hot cookware. • Overheated fats and oils can ignite very quickly. Warning! Fire hazard! • Switch the cooking zones off after each use. • Users with implanted pacemakers should keep their upper body at least 30 cm from induction cooking zones that are switched on. • Risk of burns! Do not place objects made of metal, such as knives, forks, spoons and saucepan lids on the cooking surface, as they can get hot. electrolux 3 Safety when cleaning • For cleaning, the appliance must be switched off and cooled down. • For safety reasons, the cleaning of the appliance with steam jet or high-pressure cleaning equipment is not permitted. How to avoid damage to the appliance • The glass ceramic can be damaged by objects falling onto it. • The edge of the glass ceramic can be damaged by being knocked by the cookware. • Cookware made of cast iron, cast aluminium or with damaged bottoms can • • • • scratch the glass ceramic if pushed across the surface. Objects that melt and things that boil over can burn onto the glass ceramic and should be removed straightaway. Do not use the cooking zones with empty cookware or without cookware. To avoid damaging cookware and glass ceramics, do not allow saucepans or frying pans to boil dry. The ventilation gap of 5mm between the worktop and front of the unit underneath it must not be covered. Description of the appliance ing zones. But the cross must be completely covered by the cookware. The bottom of the cookware must be from 125 - 210 mm in diameter. Cooking surface layout 1 2 Cooking over two cooking zones Large cookware can be heated with two cooking zones simultaneously. Either the two cooking zones on the left-hand side or on the right-hand side of the cooking surface are suitable for this. 1. Place cookware centrally on the two zones. The cookware must cover at least two crosses. 2. Set the same heat setting for the two cooking zones (max. setting 8). 6 5 4 3 1 Induction cooking zone 2300W, with power function 3200W 2 Induction cooking zone 2300W, with power function 3200W 3 Control panel 4 Induction cooking zone 2300W, with power function 3200W 5 Induction cooking zone 2300W, with power function 3200W 6 Control panel The cooking surface is divided into four cooking zones. In each cooking zone under the glass ceramic is an induction heating element, the middle of each one being marked with a cross on the glass ceramic surface. Cookware can be placed on any of the cook- With different cookware there can be differences in the heat distribution. Good cooking results can be achieved with cookware with thick, flat bottoms. 4 electrolux Control panel layout 11 1 10 2 1 2 3 4 5 6 7 8 9 10 11 3 9 4 8 5 7 6 Touch Control sensor fields The appliance is operated using Touch Control sensor fields. Functions are controlled by touching sensor fields and confirmed by dis- Child lock with display STOP+GO with indicator On/Off with indicator Power function Heat setting indicator Automatic switch-off indicator Residual heat indicator Heat setting selection Timer Cooking zone indicators - Timer function Timer display plays and acoustic signals. Touch the sensor fields from above, without covering other sensor fields. Sensor field / Function On / Off Switches appliance on and off Lock Locking/unlocking the control panel STOP+GO To switch the Keep Warm setting on/ off Cooking zone Off To switch off the cooking zone Heat settings To set heat settings Power Switching the power function on and off Timer Timer selection Increase settings To increase Timer time Reduce settings To reduce Timer time electrolux 5 Displays Display + number Description Residual heat Cooking zone is still hot Fault Malfunction has occurred Pan detection Cookware is unsuitable or too small or no cookware has been placed on the cooking zone Automatic switch off Switch off is active. Residual heat indicator Warning! Risk of burns from residual heat. After being switched off, the cooking zones need some time to cool down. Look at the residual heat indicator . Residual heat can be used for melting and keeping food warm. The induction cooking zones create the heat required for cooking directly in the base of the cookware. The glass ceramic is merely heated by the residual heat of the cookware. Operating the appliance Use the induction cooking zones with suitable cookware. Switching the appliance on and off Control panel Display To switch on Touch for 1 second Indicator lights up. The operational readiness indicators of the individual cooking zones also light up. To switch off Touch for 1 second Indicator goes out. The operational readiness indicators of the individual cooking zones also go out. After switching on, within approx. 10 seconds a heat setting or a function must be set, otherwise the appliance automatically switches itself off. B Setting the heat setting The control bar is touched where the desired heat setting is positioned. The heat setting is shown in the display. Correct up or down, if necessary. Do not release before the desired heat setting is reached. Locking/unlocking the control panel The control panel, with the exception of the “On/Off” sensor field, can be locked at any Control panel To switch on Touch time in order to prevent the settings being changed e.g. by wiping over the panel with a cloth. Display Indicator lights up 6 electrolux Control panel To switch off Display Indicator goes out Touch When you switch the appliance off, the locking function is automatically switched off. Switching the STOP+GO function on and off The STOP+GO function simultaneously switches all cooking zones that are switched Control panel To switch on Touch To switch off Touch Display Heat setting that was previously set (not automatic warm up function) STOP+GO does not stop the Timer function. Using the automatic warm-up function All cooking zones are equipped with an automatic warm-up function. When setting a heat setting using the automatic warm-up Step on to the keep warm setting and then back to the heat setting that was previously set. STOP+GO locks the whole control panel except the sensor field . function, the cooking zone switches to full power for a certain amount of time and then automatically switches back to the heat setting set. Control panel 1. Select warm-up setting 2. Select the desired heat setting between 1 and 8 Display display flashes The desired heat setting is displayed. display lights up. display is lit, the appliance is As long as the working at full power. After the automatic warm-up is completed, the display goes out. The length of time that the automatic warm up function operates depends on the heat setting selected. Heat setting Length of the automatic warm up [min:sec] 1 0:12 2 0:12 3 3:07 4 5:51 5 10:12 6 2:01 7 2:28 8 2:52 9 --- electrolux 7 Using the child safety device The child safety device prevents unintentional use of the appliance. Switching on the child safety device Step Control panel 1. Pilot light Switch on appliance. Do not set a heat setting. 2. Touch for 4 seconds lights up. The operational readiness indicators of the individual cooking zones light up. above lights up The child safety device is switched on. Overriding the child safety device The child safety device can be switched off in this way for a single cooking session; it remains activated afterwards. Step Control panel 1. Pilot light Switch appliance on 2. Touch for 4 seconds above lights up above goes out Until the appliance is next switched off, it can used as normal. After overriding the child safety device, a heat setting or a function must be set within approx. 10 seconds, otherwise the appliance automatically switches itself off. Switching off the child safety device Step Control panel 1. 2. Pilot light Switch on appliance. Do not set a heat setting. Touch 3. for 4 seconds above lights up above goes out Switch appliance off. The child safety device is switched off. Switching the power function on and off makes more power The power function available to the induction cooking zones, e.g. to bring a large quantity of water to the boil Control panel quickly. The power function is activated for 10 minutes at most. After that the induction cooking zone automatically switches back to heat setting 9. Display To switch on Touch The light elements in the control bar light up. The display flashes To switch off Select the heat setting 1-9 The heat setting selected is shown in the display. The display above will go out. 8 electrolux Power Management The cooking zones of the cooking surface have a maximum power. The maximum power is reached when the heat setting 8 has been set for all cooking zones. Two cooking zones generate a pair (see figure) and therefore, the power management shares the maximum available power between these cooking zones. When the power function is selected for one cooking zone, the power management makes the additional power for this cooking zone available by reducing the power of the corresponding other cooking zone. Example: the heat setting 8 is selected on one cooking zone. The power function is switched on for the corresponding cooking zone. The power function is carried out but the heat setting 8 of one of the cooking zones and the power function for the other cooking zone of the pair exceed the maximum power for both at the same time. For this purpose, the power management reduces the power of the cooking zone that switched on first from 8 to example 5 and the display of this cooking zone changes between 8 and 5 and then stays at the current possible maximum 5. (If the display changes between 8 and 5 or 8 and 3 or another value depends on the type of appliance and the size of the cooking zone.). Using the timer Function Condition Outcome after the time has elapsed Automatic cut-out a heat setting is set acoustic signal 00 flashes Cooking zone switches off Countdown timer cooking zones not in use acoustic signal 00 flashes If a heat setting is set on this cooking zone in addition to a countdown timer, the cooking zone is switched off after the time set has elapsed. Selecting a cooking zone Step Control panel If a cooking zone is switched off, the timer function set is also switched off. Display 1 Touch once Pilot light of the first cooking zone flashes 2 Touch once Pilot light of the second cooking zone flashes 3 Touch once Pilot light of the third cooking zone flashes 4 Touch once Pilot light of the fourth cooking zone flashes If other timer functions are set, after a few seconds the shortest remaining time of all the timer functions is displayed and the corresponding pilot light flashes. electrolux 9 Setting the time Step Control panel Indicator 1 Select cooking zone Pilot light for the cooking zone selected flashes 2 Touch or 00 to 99 minutes After a few seconds the pilot light flashes more slowly. The time is set. The time counts down. Switching off the timer function Step Control panel 1 Select 2 Touch Indicator Pilot light of cooking zone selected flashes faster Time remaining is displayed cooking zone The time remaining counts backwards to 00 . The pilot light goes out. The Timer function for the selected cooking zone is switched off. Changing the time Step Control panel 1 Select cooking zone 2 Touch or Display Pilot light of the selected cooking zone flashes faster Remaining time is displayed 01 to 99 minutes After a few seconds the pilot light flashes more slowly. The time is set. The time counts down. Displaying the time remaining for a cooking zone Step 1 Control panel field Select Display Pilot light of the cooking zone selected flashes faster The time remaining is displayed cooking zone After a few seconds the pilot light flashes more slowly. Switching off the acoustic signal Step 1 Control panel field Touch Acoustic signal Acoustic signal to acknowledge. Acoustic signal stops. Automatic switch off Cooking surface • If after switching on the cooking surface, a heat setting is not set for a cooking zone within approx. 10 seconds, the cooking surface automatically switches itself off. • If one or more sensor fields are covered by objects (a pan, etc.) for longer than approx. 10 seconds, a signal sounds and the cooking surface switches off automatically. • If all cooking zones are switched off, the cooking surface automatically switches itself off after approx. 10 seconds. 10 electrolux Control panel • When the appliance is switched off, if one or more of the sensor fields on the control panel are covered for more than 10 seconds, an acoustic signal sounds. The acoustic signal switches itself off automatically when the sensor fields are no longer covered. Induction cooking zones • In the case of overheating (e.g. when a saucepan boils dry) the cooking zone automatically switches itself off. is displayed. Before being used again the cooking zone must be set to 0 and allowed to cool. • If cookware that is not suitable is used, lights up in the display and after 2 mi- nutes the indicator for the cooking zone switches itself off. • If one of the cooking zones is not switched off after a certain time, or if the heat setting is not modified, the relevant cooking zone switches off automatically. is displayed. Before being used again, the cooking zone must be set to . Heat setting Switches off after 1-2 6 hours 3-4 5 hours 5 4 hours 6-9 1.5 hours Tips on cooking and frying Information about acrylamides According to the latest scientific research, intensive browning of food, especially in products containing starch, may present a health risk due to acrylamide. Therefore we recommend cooking at low temperatures and not browning foods too much. Cookware for induction cooking zones Cookware material Steel, enamelled steel Suitable + Cast iron + Stainless steel +* Cookware bottom of multilayer +* Aluminium, copper, brass - Glass, ceramic, porcelain - * Cookware for induction cooking zones is labelled as suitable by the manufacturer. Suitability test Cookware is suitable for induction cooking, if … • ... a little water on an induction cooking zone set to the highest heat setting is heated within a short time. • ... a magnet sticks to the bottom of the cookware. Certain cookware can make noises when being used on induction cooking zones. These noises are not a fault in the appliance and do not affect operation in any way. Bottom of the cookware The bottom of the cookware should be as thick and level as possible. Pan size Induction cooking zones adapt automatically to the size of the bottom of the cookware up to a certain point. However the magnetic part of the bottom of the cookware must have a minimum diameter depending on the size of the cooking zone. Cookware with a bottom with a diameter of less than 12cm is not suitable. Tips on energy saving Place cookware on the cooking zone before it is switched on. electrolux 11 If possible, always place a lid on the cookware. Heat setting Cooking process 0 Examples of cooking applications The information given in the following table is for guidance only. suitable for Cook time Tips/Hints Off position 1 Keeping food warm Keeping cooked foods warm as required Cover 1-2 Melting Hollandaise sauce, melting butter, chocolate, gelatine 5-25 mins. Stir occasionally 1-2 Solidifying Fluffy omelettes, baked eggs 10-40 mins. Cook with lid on 2-3 Simmering on low heat Simmering rice and milkbased dishes Heating up readycooked meals 25-50 mins. Add at least twice as much liquid as rice, stir milk dishes part way through cooking 3-4 Steaming Braising Steaming vegetables, fish Braising meat 20-45 mins. With vegetables add only a little liquid (a few tablespoons) 4-5 Boiling Steaming potatoes 20-60 mins. Use only a little liquid, e. g.: max. ¼ l water for 750 g of potatoes 4-5 Boiling Cooking larger quantities of food, stews and soups 60-150 mins. Up to 3 l liquid plus ingredients 6-7 Gentle frying Frying escalope, veal cordon bleu, cutlets, rissoles, sausages, liver, roux, eggs, pancakes, doughnuts Steady frying Turn halfway through cooking 7-8 Heavy frying Hash browns, loin steaks, steaks, Flädle (pancakes for garnishing soup) 5-15 mins. per pan Turn halfway through cooking 9 Boiling Searing Deep frying Boiling large quantities of water, cooking pasta, searing meat (goulash, pot roast), deep frying chips The power function is suitable for heating large quantities of liquid. Cleaning and care Warning! Sharp objects and abrasive cleaning agents will damage the appliance. Clean the appliance and remove the residues with water and washing up liquid after each use. Remove also the remnants of the cleaning agents! Scratches or dark stains on the glass ceramic that cannot be removed do not affect the functioning of the appliance. Cleaning the appliance after each use 1. Food containing sugar, plastics, tin foil residues should be removed at once using a scraper. Place a scraper on the glass ceramic surface at an angle and remove residues by sliding the blade over the surface. Wipe the appliance with a damp cloth and a little washing up liquid. Finally, rub the appliance dry using a clean cloth . 12 electrolux 2. Limescale rings, water rings, fat splashes, shiny metallic discolorations should be removed after the appliance has cooled down using cleaner for glass ceramic or stainless steel. What to do if… Problem Possible cause The cooking zones cannot be More than 10 seconds have switched on or are not operating passed since the appliance was switched on Remedy Switch the appliance on again The lock is switched on Switch off the lock (See the section “Locking/unlocking the control panel”) The child safety device is switched on Deactivate child safety device (See the section “Child safety device”) Several sensor fields were touched at the same time Only touch one sensor field Automatic switch-off has been triggered Remove any objects (pans, etc.) that are lying on the control panel. Switch appliance on again is active Switch off Acoustic signal sounds when ap- The control panel is wholly or pliance is switched off partly covered by objects. Remove objects. The residual heat indicator is not displaying anything The cooking zone was only on for a short time and is therefore not hot If the cooking zone is supposed to be hot, call your local Service Force Centre. Repeated acoustic signal (6x), appliance switches off One or more sensor fields have been covered for longer than 10 seconds Uncover sensor field Acoustic signal sounds and appliance switches itself on and then off again; after 5 seconds another acoustic signal sounds The On/Off sensor field has been covered up, e.g. by a cloth Do not place any objects on the control panel Display is switching between two Power management is reducing See the section “Switching the heat settings the power of this cooking zone power function on and off” lights up Unsuitable cookware Use suitable cookware No cookware on the cooking zone Put cookware on zone Diameter of the base of the cookware is too small for the cooking zone Move to smaller cooking zone Use suitable cookware Overheating protection for the cooking zone has been triggered Switch off the cooking zone. Switch the cooking zone on again Automatic switch-off has been triggered Switch appliance off. Switch appliance on again electrolux 13 Problem and number are displayed Possible cause Electronics fault Remedy Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house’s wiring system) If after switching on again, is displayed again, call the customer service department If you are unable to remedy the problem please contact your dealer or the Cusby following the above suggestions, tomer Care Department. Warning! Repairs to the appliance are only to be carried out by qualified service engineers. Considerable danger to the user may result from improper repairs. If the appliance has been operated incorrectly, the engineer's visit will be chargeable, even during the warranty period. • Whistling 1 Operating noises when using an individual cooking zone or Depending on the material and the processseveral cooking zones with high powers ing of the base, the following noises may ocwhen the cookware is made of different cur when using induction cooking zones. materials (Sandwich construction) • Humming 2 can occur at high power levels • Clicking 2 during electric switching processes 2 • Hissing, buzzing 3 1 The device is fitted with a fan for cooling the electrics. A whiring noise can be heard 3 when operating the fan which may deviate depending on the performance and may continue for a while after the appliance is switched off. The noises described are normal and do • Cracking noise 1 not refer to any defects. when using cookware made of different materials (Sandwich construction) Disposal The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product. Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at your local waste disposal facilities. 14 electrolux Installation instructions Safety instructions Warning! This must be read! The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc.) Installation may only be carried out by a qualified electrician. The minimum distances to other appliances and units are to be observed. Anti-shock protection must be provided by the installation, for example drawers may only be installed with a protective floor directly underneath the appliance. The cut surfaces of the worktop are to be protected against moisture using a suitable sealant. The sealant seals the appliance to the work top with no gap. When building in, protect the underside of the appliance from steam and moisture, e.g. from a dishwasher or oven. Avoid installing the appliance next to doors and under windows. Otherwise hot cookware may be knocked off the rings when doors and windows are opened. Warning! Risk of injury from electrical current. • The electrical mains terminal is live. • Make electrical mains terminal free of voltage. • Follow connection schematic. • Observe electrical safety rules. • Ensure anti-shock protection by installing correctly. • The appliance must be connected to the electrical supply by a qualified electrician. • Loose and inappropriate plug and socket connections can make the terminal overheat. • Have the clamping connections correctly installed by a qualified electrician. • Use strain relief clamp on cable. • In the event of single-phase or two-phase connection, the appropriate mains cable of type H05BB-F Tmax 90°C (or higher) must be used. • If this appliance’s mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90°C; or higher).The latter is available from the Customer Care Department. A device must be provided in the electrical installation which allows the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm Suitable isolation devices include line protecting cut-outs, fuses (screw type fuses are to be removed from the holder), earth leakage trips and contactors. Sticking the seal in the rabbet • Clean the rabbet in the work surface. • Stick the one-sided self-adhesive sealing tape supplied onto the upper surface of the rabbet along the edges of the cut-out section. – Cut the sealing tape into four pieces relating to the length of the edges of the rabbet. – For the four corners of the rabbet the ends of the sealing tapes must be cut into mitres. Do not stick the ends over one another. – Stick the sealing tape flush into the corner of the rabbet, so that no silicon compound can get under the glass ceramic when grouting. – Don’t stretch the tapes when sticking them on. electrolux 15 Assembly R10 R5 7 min. 38 min. 5 12 min. 600 min. 20 490 680 514 +1 704 +1 min. 38 min. 5 Rating Plate Modell JHD68210I Prod. Nr. – 949 593 166 Typ 55 GDD D4 AU 230 V, 50 Hz JUNO-ELECTROLUX Service In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section “What to do if…”). 16 electrolux If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners. In order to be able to assist you quickly, we require the following information: – Three-digit-letter combination for glass ceramic – Model description – Product number (PNC) – Serial number (S No. - see rating plate) – Type of fault – Any error messages displayed by the appliance electrolux 17 18 electrolux electrolux 19 www.electrolux.com 892930349-A-092008
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
advertisement