Panasonic RFP150 Operating Instructions

Concerning Compact Discs
Only compact discs bearing this mark can be used with this unit.
However, continued use of irregular shaped CDs can damage the unit.
How to remove a disc from its case
How to store the disc in its case
Label side up
How to hold a disc
Portable CD player
Operating Instructions
Dear Customer
Thank you for purchasing this product.
For optimum performance and safety,
please read these instructions carefully.
Model No.
SL-CT490
SL-CT495J
The model number and serial number
of this product can be found on either
the back or the bottom of the unit.
Please note them in the space provided below and keep for future reference.
MODEL NUMBER
SERIAL NUMBER
L
VO
ME
MO
RY
MO
DE
LL
RECA
EQ
SL-CT495J model only for U.S.A.
Supplied Accessories
Check the packing carton for these accessories.
If the surface is dirty
For U.S.A.
Wipe it with a damp cloth and then wipe dry.
Wipe from the center toward the outer circumference.
SL-CT490
Wired remote control .1
(N2QCBD000023)
Clip headphones . . . .1
(L0BAE0000026)
Play surface
(shiny surface)
Handling precautions
≥If you are taking the CD from a cold to
a warm environment, moisture may
form on the CD. Wipe this off with a
soft, dry, lint-free cloth before using the
CD.
≥Do not write on the label side with a
ball-point pen or other writing instrument.
≥Do not use record cleaning sprays,
benzine, thinner, static electricity prevention liquids or any other solvent.
≥Do not attach labels or stickers to CDs.
(Do not use CDs with exposed adhesive from tape or left over peeled off
stickers.)
≥Do not use scratch-proof protectors
etc.
Storage precautions
Be sure to store CDs in their cases to
protect them from dust, scratches, and
warping.
Do not place or store CDs in the following places
≥Locations exposed to direct sunlight
≥Humid or dusty locations
≥Locations directly exposed to a heat
vent or heating appliance
≥In the glove compartment or on the
rear deck of an automobile
For Canada
Wired remote control .1
Wired remote control .1 (N2QCBD000023)
Stereo earphones . . .1
(N2QCBD000023)
Clip headphones . . . .1 (L0BAB0000173)
(L0BAE0000026)
Jogger soft case . . . . .1
(RFC0060-K)
SL-CT495J
Use numbers indicated in parentheses when asking for replacement parts.
(Only for U.S.A.) To order accessories contact 1-800-332-5368 or web site
(http://www.panasonic.com).
Before connecting, operating or adjusting this product, please read these instructions
completely. Please keep this manual for future reference.
P
PC PY
p
Panasonic Consumer Electronics Company, Division of
Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094 http://www.panasonic.com
Panasonic Sales Company, Division of Matsushita Electric of Puerto Rico, Inc. (“PSC”)
Ave. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Panasonic Canada Inc.
RQT6367-P
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 www.panasonic.ca
F1201KN0
C 2001 Matsushita Electric Industrial Co., Ltd.
Printed in Japan
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the safety precautions listed below. Keep these operating instructions handy for future reference.
Safety
1. Power source—Connect the unit to a power source
of the type described in these instructions or as
marked on the unit.
2. Polarization—The unit is equipped with a polarized
power plug where one blade is wider than the other.
This safety feature ensures that the plug fits into your
household AC outlet only one way. If the plug doesn’t fit one way, try reversing it. If the plug still doesn’t
fit, contact an electrician to replace the obsolete outlet. Do not attempt to defeat the safety purpose of
the plug.
3. Power cord protection—Route the AC power supply cord so that it will not be walked on or pinched by
items placed on or against it. Never take hold of the
plug or cord with wet hands. Always grasp the plug
body firmly when connecting and disconnecting it.
4. Overloading—When connecting the AC power supply cord, be careful not to overload the household
AC outlet, extension cord, or outlet from any other
device as this can result in fire or electric shock.
5. Nonuse periods—Turn the unit off when it is not in
use. Unplug the unit from the household AC outlet if
it is not to be used for a long time. Unplug the unit
during lightning storms. Leaving the unit connected
to a household AC outlet for extended periods can
cause battery fluid leakage.
6. Attachments and accessories—Use only the attachments and accessories recommended in these
operating instructions.
Installation
Placement
1. Foreign material—Ensure objects and liquids do
not get into the unit. Avoid exposing the unit to excessive smoke, dust, mechanical vibration, and
shock.
2. Magnetism—Situate the unit away from equipment
and devices that generate strong magnetic fields.
3. Stacking—Do not place anything on top of this unit.
4. Wall and ceiling mounting—Do not mount the unit
on walls or ceilings unless specified in the instructions.
Environment
1. Water and moisture—Do not use the unit near
water, such as near a bathtub or swimming pool.
Avoid damp basements.
2. Heat—Situate the unit away from heat sources, such
as radiators. Do not leave it in an automobile exposed to direct sunlight with the doors and windows
closed as this may deform the cabinet.
2. Do not situate where temperatures fall below 5 oC
(41 oF) or rise above 35 oC (95 oF).
Maintenance
(See page 7 for details.)
Unplug the unit from the household AC outlet before
cleaning.
Clean with a damp cloth.
Do not use abrasive pads, scouring powders, or solvents.
Service
1. Damage requiring service—The unit should be
serviced by qualified service personnel if:
1. (a) The AC power supply cord or AC adaptor has
been damaged; or
1. (b) Objects or liquids have gotten into the unit; or
1. (c) The unit has been exposed to rain; or
1. (d) The unit does not operate normally or exhibits a
marked change in performance; or
1. (e) The unit has been dropped or the cabinet damaged.
2. Servicing—Do not attempt to service the unit beyond that described in these operating instructions.
Refer all other servicing to authorized servicing personnel.
3. Replacement parts—When parts need replacing
ensure the servicer uses parts specified by the manufacturer or parts that have the same characteristics
as the original parts. Unauthorized substitutes may
result in fire, electric shock, or other hazards.
4. Safety check—After repairs or service, ask the servicer to perform safety checks to confirm that the unit
is in proper working condition.
SL-CT490 : indicates a feature which can be enjoyed
with SL-CT490 only.
SL-CT495J. : SL-CT495J only.
This manual was printed with soy based ink.
1
Power Supply Preparations
Refer to the specifications (page 8) for information on operating times when using rechargeable batteries or dry cell batteries.
Using the AC adaptor (not included)
2
Use only the recommended AC adaptor. Using other
adaptors can cause overheating which can lead to fire.
For U.S.A
To order the optional AC adaptor RP-AC46 contact 1800-332-5368 or web site (http://www.panasonic.com).
For Canada
Be sure to obtain the optional AC adaptor RP-AC46.
it is available through your Panasonic dealer.
Connect the AC adaptor.
DC IN jack (K DC IN 4.5 V)
HOLD
DC IN 4.5V
Household
AC outlet
AC adaptor
(Refer to “Using the AC adaptor”.)
Recharging starts and the “H” charging indicator
flashes on the unit’s display. The indicator goes
out when charging is complete.
When charging is complete, unplug
the AC adaptor from the household
AC outlet and DC IN jack.
≥Never mix dry cell and rechargeable batteries.
≥Turn the unit off before replacing the rechargeable batteries.
Note!
Side panel of
the unit
Ë
3
Connect the AC adaptor.
Conserving power
To save power when the unit is not to be used for a long
time, unplug the AC adaptor from the household AC
outlet. Reprogram tracks if necessary before use.
Note!
Turn the unit off before connecting or disconnecting the
AC adaptor.
≥Rechargeable batteries have a service life of approximately 300 charge-discharge cycles. The batteries
have reached the end of their operational life if they
last for a noticeably shorter time after recharging, or if
they cannot be recharged at all. Replace the batteries.
≥Recharging may only be performed when the unit is
powered off.
≥The AC adaptor and rechargeable batteries may become warm while recharging is in progress. This is not
a malfunction.
≥Leaving the AC adaptor connected can cause the batteries to go flat. After recharging the batteries and disconnecting the AC adaptor from the AC power outlet,
ensure you disconnect the AC adaptor from the unit’s
[KDC IN 4.5 V] terminal.
If the battery lid
comes loose
Removing
batteries
Slide the lid back into
place horizontally.
Push up on the battery
in the direction indicated by the arrow. Then
lift it out.
Using the rechargeable batteries
(not included)
OPEN
OPEN
Obtain the optional rechargeable batteries.
Make sure to recharge the batteries before using them.
The unit cannot be used to charge rechargeable batteries other than those specially designed for it.
Optional batteries: P-3GAVA/2B
Charging procedure
1
Insert the special rechargeable batteries into the unit.
2
3
OPEN
OPEN
OPEN
1
+
L
VO
DE
O
M
MEM
ORY
RE
CA
LL
EQ
≥The unit is powered on accidentally when not in use,
causing the batteries to run down.
≥A button is accidentally pressed during play, interrupting the operation.
To use the HOLD function
Set [HOLD] to the HOLD position.
HOLD
HOLD
HOLD mode
EQ
HOLD
HOLD mode
2
The unit and wired remote control have HOLD functions, each of which works independently.
“(” indication
Release
When the main unit is in HOLD mode, pressing any button causes the indication “(” to appear on the display.
When the unit is powered off
The “(” indication appears only when [1/;] (main
unit) is pressed.
HOLD
This indicator flashes when the batteries are almost out
of power. Power is cut off completely a short while later.
Rechargeable batteries: Recharge batteries.
Dry-cell batteries: Replace batteries with new ones.
Note!
≥The length of time the unit will continue to operate between when the battery indicator starts flashing and
when the power is cut off differs depending on the
type of batteries used.
≥The battery indicator may not be displayed if rechargeable batteries other than those designated by
Panasonic are used.
Using the car adaptor (not included)
Be sure to obtain the car adaptor (SH-CDC9), available
as an optional accessory.
The car adaptor can be used to recharge the unit’s batteries while in the car.
CAUTION:
Use only car adaptor, Model: SH-CDC9 manufactured by Matsushita Electric Industrial Co., Ltd.
If the unit malfunctions or freezes during
use, disconnect the power source (the AC
adaptor or batteries).
Re-connect the power source and continue operation.
Anti-Skip System
The HOLD function prevents the following:
EN
OP
C
Battery indicator
After disconnecting the AC adaptor, insert two “LR6,
AA, UM3” alkaline batteries.
The procedure for inserting and removing dry cell
batteries is identical to that for rechargeable batteries.
This function causes the unit to ignore short, accidental
button presses. (The disc lid can still be opened and
closed.)
Ë
S-XBS
Using the dry cell batteries
(not included)
HOLD function
HO
LD
Battery indicator
This system deals with skipping in a variety
of ways:
≥The thinner and lighter construction makes the unit
less susceptible to vibration.
≥An anti-skip mechanism prevents skipping caused
when play speed changes due to swinging of the unit.
≥A recovery system immediately returns the laser pickup to its original position if it is knocked off the track by
a strong shock.
≥Anti-skip (max. 48 seconds) memory fills in interruptions caused by bumps and vibrations.
The anti-skip system works automatically while the
system is on and cannot be canceled.
.
When bumps continue repeatedly
The elapsed playing time disappears and sound is interrupted.
S-XBS
HOLD
Release
Before operating the buttons
Be sure to move [HOLD] to release the unit from
the HOLD mode.
Note!
≥While the system is on, the disc rotates at a higher
rate than usual in collecting extra audio data. This
could result in a slight increase in disc rotation noise.
≥The anti-skip memory compresses digital signals.
Sequential Play Basic Play
Close the lid
1
4
OPEN
Label must face
upward.
Press
near the center
so the disc clicks
firmly into place.
Track number in play
C
RE
C
EQ AL
L
2
ME
MO
RY
M
O
DE
VO
L
S-XBS
R
L
Elapsed playing time of each track
Decrease
VOL
HO
LD
N
E
P
O
Ë
3
HOLD
5
Plug type:
3.5 mm (1/8 in.) stereo
S-XBS
C
Follow steps 1–5.
In step 2: Connect the clip headphones/ stereo earphones and wired remote control to the headphone jack [Ë] .
(Plug in firmly.)
In step 5: The volume range is 0-25. Press and hold to change the volume successively. The volume changes when
pressed while the level is displayed. If any other display is shown, it changes to show the current level.
(The volume returns to 10 when you disconnect the power source.)
≥Play stops automatically when all the tracks have been played.
≥If the unit has been connected to the car audio system, set this unit’s volume to 10, then adjust the volume level on
the system.
Operation
Button
Display/reference
Press again to restart play.
Press during play.
C
To pause play
Increase
VOL
VOL
For your reference:
“)” indication
This indication appears for about 30 seconds if [1/;] is
pressed when no disc is loaded in the unit or if the disc
is not properly secured.
“*” indication
This indication appears for about 10 minutes when the
cover is opened. (However, the indication does not appear when the unit is powered off.)
Removing discs
1 Press [∫] to stop play and disc rotation.
2 Slide [OPEN 1] to open the lid.
3 Once the disc has stopped, lift the disc
out with your finger.
Do not stop the disc by hand or try to remove it before it
stops rotating. This can damage CDs.
Total number of tracks
Press during play.
To stop play
Stop mode
To turn off the
unit
C
Resume function
Play starts from the beginning of
the current track the next time you
press [1/;].
Press during stop mode.
Total playing time
No indicator is shown.
C
Auto-off function
Off mode
Skip forward/
backward
(skip function)
Rapid forward/
backward
(search function)
Press during play.
(Press [:] twice to skip to the
beginning of the previous tracks.)
Backward
Forward
≥During program play (page 4), these buttons are
used to skip forward or backward through the
programmed sequence of tracks.
≥You cannot skip to tracks that have been played
in random or random repeat play (page 4).
≥During program play, 1-track repeat play, random
play and random repeat play (page 4), search operation is limited to the current track only.
Press and hold during play.
Resume function notes
3
Note!
Never insert foreign objects into the unit.
≥Opening the lid while in the stop mode or replacing the disc while in the off mode cancels the function. (It may remain active if you replace a disc in the off mode.)
≥Play may resume from the beginning of the next track if you stopped play near the end of a track.
≥The resume function works automatically and cannot be turned off.
If you leave the unit in stop mode for about 10 minites
(30 seconds if disc is not loaded), it turns off to save the
batteries.
Note on CD-R and CD-RW
This unit can play CD-DA format audio CD-R and
CD-RW that have been finalized§ upon completion
of recording. It may not be able to play some CD-R
or CD-RW due to the condition of the recording.
§Finalizing is a process that enables CD-R/CD-RW
players to play audio CD-R and CD-RW.
Other Play Methods
The letters such as D in the various illustrations refer to the descriptions in the “Location of Controls” section.
Skip play
Program play
Repeat play/Random play
The disc plays from the specified track through to the
end, then play stops automatically.
Preparation: Put unit in stop mode.
Up to 24 tracks can be entered in the programmed sequence.
Preparation: Put unit in stop mode.
Press during play or stop mode.
1
1
Select the desired track.
D
D
2
2
F
The setting is switched in the sequence indicated below
each time [MODE] is pressed.
1-track repeat (1 `)( ----------------]
Register in sequence.
(The indication “M” and the programmed sequence appear on the display.)
C
MODE
Select the desired track.
All-track repeat (`)
3
H
RECALL
Random repeat (RANDOM `) |
The tracks play repeatedly in random |
Repeat steps 1 and 2 to program all
the desired tracks.
4
The setting switches in the sequence indicated below
each time [EQ] is pressed.
The tracks play once each in random
order and then play stops.
|
|
v
Cancel (no indicator is shown) --------------}
When pressed during program play
1-track repeat (1 ` M)(------------]
One track is repeated.
v
S-XBS>TRAIN>Cancel (no indicator is shown)
∫ To program the same track in the sequence more than once
Select this setting to boost the low frequency response.
∫ After step 2, press [MEMORY, RECALL] the desired
number of times.
TRAIN:
Select this setting to avoid annoying other passengers
with noise from your headphones/earphones while riding on the train, or to reduce fatigue when listening for a
long period of time.
|
The programmed tracks are repeated. |
v
|
Cancel (M) -------------------------------------------}
Note!
∫ No more tracks can be programmed.
≥You can select the first track to play in random play
and random repeat play by pressing [9] while the
disc is stopped. All the tracks are played.
≥You cannot select random play or random repeat play
during program play.
≥The resume function does not work when random or
random repeat are on.
≥The mode is canceled when you disconnect the power
source.
∫ Press [MEMORY, RECALL] while the disc is playing.
(The number of the programmed tracks appear on
the display in sequence.)
The setting returns to S-XBS when you disconnect the
power source.
Memory repeat (` M)
|
|
∫ If “'” is displayed
∫ To confirm the contents of the program
Note!
|
|
|
The setting is switched in the sequence indicated below
each time [MODE] is pressed.
C
^==========b
S-XBS:
|
Random (RANDOM)
order.
EQ
|
All the tracks on the disc are repeated. |
v
|
v
Press during play or stop mode.
|
|
MEMORY
G
Changing the sound quality
One track is repeated.
v
∫ To delete the entire programmed sequence
∫ Press [∫].
Note!
The repeat and random play modes are canceled after
steps 1 and 2.
Location of Controls
A
C DE
Side panel of the unit
F
B
HOLD
Ë
M
O
DE
VO
L
DC IN 4.5V
ORY
G
RE
C
EQ ALL
MEM
A
J K L
H
M
Back panel of the unit
HO
LD
N
E
P
O
Ë
I
B
N
AB C
VOL
D
EQ
HOLD
H
GF E
4
Portable CD player A
Wired remote control B
A Stop/operation off button
(∫)
B Display
C Play/pause button (1/;)
D Skip/search buttons
(:, 9)
E Headphone volume control
buttons (j, VOL, i)
F Mode button (MODE)
G Memory/recall button
(MEMORY, RECALL)
H EQ button (EQ)
I Open switch (OPEN1)
J Handstrap hole
K DC IN jack (K DC IN 4.5 V)
L Hold switch (HOLD)
M Headphone jack (Ë)
N Hole for car mounting base
A Skip/search buttons
(:, 9)
B Play/stop/operation off button
(∫/1)
C Volume control buttons
(j,VOL,i)
D Headphone jack/ earphone
jack
E Clip
F Hold switch (HOLD)
G EQ button (EQ)
H Plug
Using the Wired Remote Control
The remote control can be operated regardless of the
HOLD mode of the unit.
Basic operation
Preparation:
Press once during off or stop mode.
Release the remote control from the HOLD mode.
EQ
Skipping
tracks
HOLD
VOL
To start play
Press during play.
(Press [:] twice to skip to the beginning of the previous tracks.)
Backward
(Beep Beep Beep)
VOL
(Beep)
HOLD
Press once during play.
Forward
Searching
through tracks
(Beep Beep)
VOL
To stop play
Press and hold during play.
∫ Operation confirmation tones
» When an operation button is pressed, a confirmation
(Beep...Beep)
tone sounds. Refer to the parentheses in the illustration for the different types of confirmation tones.
VOL
Press and hold during play or stop
mode.
∫ Turning the operation tones off and on
» While stopped or during play
» Press and hold [EQ] on the remote control for 5 sec-
To turn off
the unit
onds until the unit's display appears. The tone
sounds when the setting is changed.
(Beep)
HOLD
VOL
(Beep)
To adjust the
volume
≥The volume range is 0–25. (Press
and hold to change the volume successively.)
≥A tone (beep-beep) sounds when
you reach the minimum or maximum
volume.
VOL
(Beep...Bee...p)
EQ
Increase
Decrease
EQ
Changing the sound quality
To turn the tone off
To turn the tone on
The setting switches in the sequence indicated below each time
[EQ] is pressed.
Press during play or stop mode.
S-XBS>TRAIN>Cancel (no indicator is shown)
EQ
HOLD
EQ
^==========b
S-XBS:
(Beep)
Select this setting to boost the low frequency range response.
TRAIN:
Select this setting to avoid annoying other passengers with noise
from your headphones/earphones while riding on the train, or to
reduce fatigue when listening for a long period of time.
Note!
The setting returns to S-XBS when you disconnect the power
source.
Using the Unit with Optional Accessories
Using the unit with an audio system
Use only the specified car stereo cassette adaptor
and car adaptor. Using other adaptors can cause
overheating which can lead to fire.
The part numbers are indicated in parenthesses.
MEM
ORY
M
O
DE
VO
L
Items to be purchased
RE
C
EQ ALL
Turn off this unit and the other equipment before connection.
1 Connect the remote control to [Ë] on the unit.
2 Connect the stereo connection cable to the remote control and the other equipment.
≥The unit may malfunction if you connect directly to
[Ë] on the unit.
≥Do not connect the cable to the PHONO jacks on
the amplifier.
3 Turn the operation tones off (see above) so they
are not heard when you press buttons on the remote control.
4 Set the volume to 10.
Make further volume adjustments with the other
equipment.
Using the unit with a car audio
system
Other equipment
HO
LD
N
E
P
O
Ë
(White)
L To CD or
AUX
Headphone jack (Ë)
(Red) R terminals
Note!
≥Obtain the optional connecting cable if the other
equipment comes with mini-phone jacks.
≥If you connect speakers (active or otherwise) directly to
the unit's headphone jack, ensure they have an impedance of 1 k≠ or less.
VOL
Stereo connection cable (not included)
For connection to the car audio system
Car stereo cassette adaptor (SH-CDM10A)
Connect the car stereo cassette adaptor to the earphone jack of th remote control and connect it to
the unit’s headphone jack. Set this unit’s volume to
10.
For securing the unit and connecting the power
supply:
≥Car adaptor (SH-CDC9)
≥Car mounting kit (SH-CDF20)
Note when using the car mounting kit (SH-CDF20)
1Remove the screw from
Bracket
the bracket at the rear
of the car mounting
base.
2Replace the screw in the
lower hole of the bracket.
Screwdriver
Note!
5
≥When you switch off the car, volume and sound quality
may return to the original settings and the resume
function may work even if you change the disc.
≥It may not be possible to use the unit with some types
of car stereos owing to restrictions imposed by the
construction of the car stereo cassette adaptor.
For further details, refer to the instructions of the part
concerned.
RQT6367
ONLY FOR U.S.A.
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094
Panasonic Sales Company, Division of Matsushita
Electric of Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Panasonic Portable Audio Limited Warranty
Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the Warrantor”) will repair or replace this product with new or refurbished parts or equivalent product, free of charge in the U.S.A. or Puerto Rico, in the
event of a defect in materials or workmanship as follows ( all time periods commence
from the date of original purchase ) :
PARTS & LABOR - ONE (1) YEAR
Non-rechargeable batteries are not warranted
Rechargeable batteries - (when applicable) exchange defective item for new one for ten
(10) days.
For assistance in the continental U.S.A. in obtaining repairs please ship the product to:
Panasonic Services Company - Customer Servicenter
Suite B 4900 George McVay Drive
McAllen, TX 78503
In Puerto Rico contact the Panasonic Sales Company.
Tel. (787) 750-4300
Fax. (787) 768-2910
When shipping the unit carefully pack and send it prepaid, adequately insured and
preferably in the original carton. Include a letter detailing the complaint and provide a
day time phone number where you can be reached.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD THE PURCHASER WILL
BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED
WITHOUT SUCH PROOF OF PURCHASE.
Also, the purchaser will be responsible for shipping the unit to the above address.
This warranty is extended only to the original purchaser.
This warranty only covers failures due to defects in materials and workmanship which
occur during normal use. The warranty does not cover damage which occurs in shipment, or failures which are caused by products not supplied by the warrantor, or failures
which result from accident, misuse, abuse, neglect, mishandling, faulty installation, misapplication, improper insertion of consumables, set-up adjustments, maladjustment of
consumer controls, improper operation or maintenance, improper antenna, inadequate
signal reception or pickup, alteration, modification, power line surge, improper voltage
supply, lightning damage, commercial use or service by anyone other than a PANASONIC SERVICES COMPANY authorized repair facility, or damage that is attributable
to acts of God.
LIMITS AND EXCLUSIONS
There are no express warranties except as listed above.
THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES OR
DISCS) RESULTING FROM THE USE OF THIS PRODUCTS, OR ARISING OUT OF
ANY BREACH OF THE WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE APPLICABLE WARRANTY PERIOD SET
FORTH ABOVE.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or
limitations may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
If you have a problem with this product that is not handled to your satisfaction, then write to the Consumer Affairs Department at the Company address indicated above.
For Product Information, Operating Assistance, Literature Request, Dealer Locations, and all Customer Service inquiries please contact:
1-800-211-PANA(7262), Monday - Friday 9 am - 9 pm, Saturday - Sunday 9 am - 7 pm, EST.
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate your nearest
servicenter by visiting our Web Site.
Accessory Purchases:
1-800-332-5368 (Customer Orders Only)
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032 (6 am to 5
pm Monday - Friday; 6 am to 10:30 am Saturday, PST)
(Visa, MasterCard, Discover Card, American Express, Check)
Product Service
1. Damage requiring service—The unit should be serviced by qualified service personnel if:
1. (a) The AC power supply cord or AC adaptor has been damaged; or
1. (b) Objects or liquids have gotten into the unit; or
1. (c) The unit has been exposed to rain; or
1. (d) The unit does not operate normally or exhibits a marked change in performance; or
1. (e) The unit has been dropped or the cabinet damaged.
2. Servicing—Do not attempt to service the unit beyond that described in these operating instructions. Refer all other servicing to authorized servicing personnel.
3. Replacement parts—When parts need replacing ensure the servicer uses parts
specified by the manufacturer or parts that have the same characteristics as the
original parts. Unauthorized substitutes may result in fire, electric shock, or other
hazards.
4. Safety check—After repairs or service, ask the servicer to perform safety checks
to confirm that the unit is in proper working condition.
User memo:
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER
6
Product information
For product information or assistance with product operation:
In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262, or email consumerproducts @panasonic.com, or web site (http://www.panasonic.com).
For assistance in the continental U.S.A. in obtaining repairs please ship the product to:
Panasonic Services Company - Customer Servicenter
Suite B 4900 George McVay Drive
McAllen, TX 78503
In Puerto Rico contact the Panasonic Sales Company.
Tel. (787) 750-4300
Fax. (787) 768-2910
When shipping the unit carefully pack and send it prepaid, adequately insured and
preferably in the original carton. Include a letter detailing the complaint and provide a
day time phone number where you can be reached.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD THE PURCHASER
WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE
INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Also, the purchaser will be responsible for shipping the unit to the above address.
In Canada, contact Panasonic Canada Inc. Customer Care Centre at 905-624-5505,
web site (www.panasonic.ca), or an authorized Servicentre closest to you.
Maintaining the Lens
Using clip headphones Only for U.S.A.
1
2
Hook
Open the lid and clean the lens as shown in the figure. Use a cotton swab to gently
wipe off any finger-prints.
Recommended product: Lens cleaner kit (SZZP1038C)
Air blower for
camera lens
Lens
1 Press on the base of the clip to open it.
2 Fit the hook over your ear so the end fits behind your
earlobe.
Using jogger soft case
SL-CT495J
Lens
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
OPEN
Ë
LD
HO
BAT
T
EXT
EQ
LL
RECA
MEM
ORY
E
MOD
VOL
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE THIS APPARATUS TO RAIN,
MOISTURE, DRIPPING OR SPLASHING AND THAT NO OBJECTS
FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON
THE APPARATUS.
1 Before jogging with this unit, allow
sufficient time for the memory
buffer to fill up completely (ideally
48 seconds).
2 Fasten the neoprene sport belt
securely around your waist so that
the unit fits snugly against your
body.
3 Be sure the CD player is placed in
the pouch so that the buttons are
facing away from your body.
4 This unit is designed for light jogging, but not for serious running. It
may occasionally skip if used by
an aggressive runner, or by
someone with a heavy, jarring
stride.
Notei
≥Do not machine wash.
≥Fading and loss of shape can
occur.
≥Do not expose the pouch to high
temperatures when a player and
CDs are inside.
≥The player and CDs can be damaged and it can lead to fire. Be especially careful not to leave the
pouch near heaters, in a car, or in
the sun.
≥Do not drop or hit the pouch while a
player and CDs are inside.
≥This can seriously damage the player and CDs.
≥Discontinue use if a rash or skin irritation develops.
≥Take special care when listening to
CDs around traffic.
THE FOLLOWING APPLIES ONLY IN THE U.S.A.:
CAUTION:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
≥Reorient or relocate the receiving antenna.
≥Increase the separation between the equipment and receiver.
≥Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
≥Consult the dealer or an experienced radio/TV technician for help.
Any unauthorized changes or modifications to this equipment would void the
user’s authority to operate this device.
Attaching a handstrap (not included)
Attach a handstrap, to make carrying the unit easier.
DC IN 4.5V
Handstrap (not included)
Handstrap hole
DC IN 4.5V
7
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Specifications
Audio
No. of channels: 2 (left and right, stereo)
Frequency response:
20 to 20,000 Hz
(i0 dB to j7 dB)
DA converter:
1 bit, MASH
Headphone
output level: RMS max. 8 mWi8 mW/
16 ≠ (adjustable)
Pickup
Light source:
Wavelength:
Semiconductor laser
780 nm
General
Operational temperature
range:
0 eC–40 eC
(32 eF–104 eF)
Rechargeable temperature
range:
5 eC–40 eC
(41 eF–104 eF)
Power supply:
DC 4.5 V with optional
AC adaptor RP-AC46
Troubleshooting Guide
Play time:
[When used in hold mode with EQ
canceled, at 25 eC (77 eF), on a flat,
stable surface].
Batteries
used
2 alkaline
batteries
Play time
Before requesting service, make the below checks. If you are in doubt about some of
the check points, or if the remedies indicated in the chart do not solve the problem:
In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262,
or e-mail [email protected], or web site
(http://www.panasonic.com).
In Canada, contact Panasonic Canada Inc. Customer Care Centre at 905-6245505, web site (www.panasonic.ca), or an authorized Servicentre close to you.
About 40 hours
Problem
2 rechargeable
Ni-Cd batteries
(P-3GAVA/2B)
About 18 hours
≥Rechargeable batteries are optional.
≥The play time may be less depending
on the operating conditions.
≥Play time will be considerably reduced
when playing CD-RW
Recharging time:
About 3 hours
Dimensions (WaHaD):
132a23.3 a136.5 mm
(53⁄16za29⁄32 za53⁄8z)
Mass:
200 g (7.1 oz.) (with batteries)
154.0 g (5.4 oz.) (without batteries)
Note:
Specifications are subject to change
without notice.
Mass and dimensions are approximate.
Check this
Cannot close the lid.
Is the disc properly secured in place?
Cannot play discs.
≥Is the unit in HOLD mode?
≥Is the disc properly secured in place?
≥Is there condensation on the lens?
(Wait for about an hour and then try again.)
≥Is the disc dirty or scratched?
Tracks on disc do not play
in order, starting with the
first track.
≥Is the random play mode on?
≥Did you stop play in the middle of the disc last
time?
Cannot hear music—too
noisy.
≥Have the headphone/earphone and wired remote
control plugs been inserted firmly?
≥Are the plugs dirty? (Wipe away dirt on plug.)
≥Separate the unit from mobile phones.
TV picture is distorted.
Radio reception is noisy.
Are you using the unit too near a TV or tuner?
(Keep the unit away from the TV or tuner.)
Cautions
Listening caution
EST. 1924
Do not play your headphones or earphones at a high
volume. Hearing experts advise against continuous extended play.
Selection and care of rechargeable /dry cell batteries
∫ Selection
∫ Care
As a safety precaution, the portable CD players made
by Panasonic are constructed so it is impossible to
recharge ordinary batteries.
Only batteries especially designed for this unit can be
recharged.
≥Special rechargeable Ni-Cd batteries:
To prevent battery damage, electrolyte leakage and
short-circuiting, heed the following points.
≥Do not peel off the covering on batteries and do not
use if the covering has been peeled off.
≥Align the poles + and - correctly when inserting the
batteries.
≥Do not mix different types of batteries or old and new
batteries.
≥Remove the batteries if you do not intend to use the
unit for a long time.
≥Do not throw into fire, short-circuit, disassemble, or
subject to excessive heat.
≥Do not attempt to recharge dry cell batteries.
≥Do not allow metal objects to touch the battery terminals as this may cause short-circuiting which is dangerous.
≥When carrying batteries in a pocket or bag, ensure no
metal objects such as necklaces are placed together
with them. Contact with metal may cause short-circuiting which can cause a fire. For safety, carry the batteries in the battery carrying case.
P-3GAVA/2B (set of 2)
If you experience a ringing in your ears, reduce volume
or discontinue use.
Do not use while operating a motorized vehicle. It may
create a traffic hazard and is illegal in many areas.
For details, check with your dealer.
Special rechargeable
batteries
Ordinary dry cell
batteries/rechargeable
batteries
You should use extreme caution or temporarily discontinue use in potentially hazardous situations.
Even if your headphones or earphones are the open-air
type designed to let you hear outside sounds, don’t turn
up the volume so high that you can’t hear what’s around
you.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of sound. So what
sounds “normal” can actually be loud and harmful to
your hearing.
Guard against this by setting your equipment at a safe
level BEFORE your hearing adapts.
To establish a safe level:
≥Start your volume control at a low setting.
≥Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.
Once you have established a comfortable sound level:
≥Leave it there.
8
≥If rechargeable battery play time is short after recharging, the batteries have reached the end of their service
life. Replace them with the recommended replacements.
≥Play time may be shorter than usual after recharging
batteries for the first time or after they have been unused for a long time. Repeatedly recharge and discharge the batteries if this occurs to restore them to
normal.
When driving a car
In the interest of traffic safety, do not operate the unit
while driving.
Discontinue use if you experience discomfort with
the headphones, earphones or any other parts that
directly contact your skin. Continued use may
cause rashes or other allergic reactions.
">