Craftsman CVCS107 Instructions / Assembly

722790217
01CI
(CVS107)
Owner’s Manual
& Assembly Guide
Model No.
71-65035 United States
10’ x 7’
Gloves must be worn
at all times to reduce
risk of injury!
Nominal Size
Customer Service:
1-800-851-1085
or
[email protected]
BUILDING DIMENSIONS
Approx.†
Size
10’ x 7’
3,0 m x 2,0 m
Storage
Area
64 Sq. Ft. 432 Cu. Ft.
2
6,0 m
12,2 m3
* See Inside for Detailed Safety Information.
Base
Size
For proper base construction see page 12
†
Size rounded off to the nearest foot
Exterior Dimensions
(Roof Edge to Roof Edge)
Width
Depth
Height
121” x 81”
307,3 cm x 205,7 cm
Interior Dimensions
(Wall to Wall)
Width
Depth
Height
Door
Opening
Width
Height
123 1/4”
83 1/2”
90 5/8”
118 1/4”
78 1/4”
89 3/8”
59 1/2”
69 1/4”
313,1 cm
212,1 cm
230,2 cm
300,4 cm
198,8 cm
227,0 cm
151,1 cm
175,9 cm
SAFETY PRECAUTIONS...
02H
Safety precautions MUST be followed at all times throughout the construction of your building!
Care must be taken when handling various pieces
of your building since many contain sharp edges.
Please wear work gloves, eye protection and
long sleeves when assembling or performing any
maintenance on your building.
Practice caution with the tools being used in the
assembly of this building. Be especially familiar with
the operation of all power tools.
Keep children and pets away from the worksite
during construction and until the building is
completely assembled. This will help avoid
distractions and any accidents which may occur.
Do NOT attempt to assemble your building on a
windy day. The large panels can catch the wind like
a “sail”, causing them to be whipped around making
construction difficult and unsafe.
Do NOT attempt to assemble your building before
double checking that you have all the parts indicated
in the parts lists (page 8) as well as all hardware
(page 7). Any building left partially assembled may
be seriously damaged by even light winds.
IMPORTANT NOTE ON ANCHORING
NEVER concentrate your weight on the roof of the
building. When using a step ladder make sure that
it is fully open and on even ground before climbing
on it.
• Your building MUST be anchored to prevent wind
damage. An anchoring kit is not supplied with your
building and you have many options when it comes to
anchoring. See anchoring page for more info.
• You must also have a temporary anchoring system in
place in case you need to take a break from assembly.
See page 4 for more info.
2
ASSEMBLY TIPS & TOOLS
03A
Watch the Weather Closely:
Be sure the day you choose to install your building is dry and calm.
Do NOT attempt to assemble your building on a windy day. Be careful on wet or muddy ground.
Use Teamwork: Two or more people are required to assemble your building. One person can hold
the parts or panels in place while the other person fastens them together and handles the tools. This
makes the process of assembling your building faster and safer.
Tools and Materials:
Here is a list of some basic tools and materials you will need to assemble
your building. Decide which method of anchoring and the type of base you will use to make a complete
list of the materials you will need.
WHAT YOU NEED
RECOMMENDED TIME SAVERS
BASE PREPARATION TOOLS
•
•
•
•
•
•
•
•
Work Gloves
Safety Glasses
Step Ladder
No. 2 Phillips Screwdriver (Magnetic Tip Preferred)
Utility Knife or Scissors
Pliers
Carpenter’s Level
Tape Measure
•
•
•
•
•
Power Drill (Cordless, Variable Speed)
Nut Driver or Wrench
Square
String (for squaring the frame)
Awl (to align holes)
•
•
•
•
Lumber and/or Concrete
Hammer and Nails
Spade or Shovel
Hand Saw or Power Saw
How to Select and Prepare Your Building Site:
Before you start to assemble your
building, you will want to decide on a good location. The best location is a level area with good drainage.
• Allow enough working space so it is not difficult to move parts into position for assembly. Be sure there will be enough
space at the entrance for the doors to completely open. Also, there needs to be enough space outside the building to be
able to fasten the panel screws from the outside.
• Before assembling any parts, your base should be constructed and an anchoring system should be ready to use.
3
04A
FREQUENTLY ASKED QUESTIONS
Q. How long will it take to assemble the building?
A. Assembly time depends on a variety of factors, including roof design, tools available, DIY skill and the pace
at which you work. Guidelines for each shed assembly are approximate AFTER completion of the base, and
assume two or more people working on the assembly. Generally, you should plan on at least one day working with
someone who can assist you; again, after constructing the base. Refer to the clock icons on each product page
on the website for specific time estimates.
Q. How do I decide where to put my shed?
A. The key to a successful assembly is to make sure the shed will be square and level when built. The shed can
be assembled directly onto level ground (grass or dirt). If you have location options, choose one that is already
flat, with good drainage to control moisture. If you don’t have a flat, well-drained area, you need to prepare the
space. Level the area using cinder blocks, concrete, crushed gravel or other sturdy materials. Once level with good
drainage, construct your base. Using a carpenter’s level, make sure your base is level and free of bumps or ridges
to provide good support for your building.
Q. What if I can’t finish my building in one session?
A. If weather conditions change so that it becomes windy or rainy, it is recommended that you stop assembly
until conditions improve. This is for your safety and for protection of the shed panels. However, do not leave
your unfinished construction without first temporarily anchoring the corners of the shed to your base and placing
weights, such as patio blocks or sandbags, on the floor frame. Failure to anchor the building if you leave it while
partially assembled could result in irreparable damage or personal injury if the building collapses.
Note: Most instruction manuals provide a warning note at the beginning of the installation step for corner panels,
stating that the remainder of the building assembly requires multiple hours and more than one person. Do not
continue beyond this point if you do not have enough time or help to complete the assembly that day. A partially
assembled building can be severely damaged by even light winds.
Q. Do I need to anchor my building?
A. Yes! Fully assembled buildings should be anchored using a permanent anchoring system. If you need to leave
your building before it is completely assembled, you will need to temporarily anchor the corners of the shed to your
base, and place weights, such as patio blocks or sandbags, on top of the floor frame.
Q. How do I temporarily anchor my building before it’s fully assembled?
A. An incomplete building must be anchored before breaking for any period of time to prevent possible damage.
•If the building is on a wood base, secure the frame with wood screws in the corners
•If the building is on a concrete base, temporarily anchor the frame in the corners
•Use patio blocks or sandbags on top of the floor frame as weights
•Secure the floor frame to the ground with ground augers or rope the frame in the corners to the ground
Q. How do I control condensation and prevent water from leaking in?
A. To minimize condensation, install a continuous, unbroken plastic
vapor barrier with a thickness of 6 mil.
between exposed ground surface and the building’s base. Make sure that all weather stripping and washers are
used throughout the assembly process. Make sure that the weather-stripping tape adheres to the panels when
installing it along the main ridge beam. Do not stretch it. Apply it directly off the roll onto clean panels. Ensure
that all washers are flush with the panels and do not over-tighten screws, as this can crack the washers. Silicone
caulking may be used to create watertight seals at the washers and throughout the building.
4
05P
Q. What kind of base do I use?
A. You can:
•Use a Craftsman Floor Frame Kit
•Pour a concrete slab
•Build a wood deck/floor (use exterior-grade plywood)
•Use patio blocks
•Build on crushed gravel, dirt or grass
Craftsman provides a floor frame kit accessory that is an option for most building sizes. If you are building a wood
deck/floor, a Craftsman floor frame kit on top of your deck/floor assembles in minutes and provides a floor frame
suitable for a 5/8” exterior-grade plywood floor (not included). A continuous unbroken plastic vapor barrier with a
thickness of 6 mil. between the ground and the building’s base is also recommended.
Q. How should I measure for my base?
A. Shed dimensions are provided in “nominal” size. Nominal sizes are roof-edge measurements rounded to the
nearest foot and are not the measurements to use for constructing the shed base. So, carefully check the exact,
recommended base size in the specifications for your shed model.
Q. How do I align the holes in the wall panels with the holes in the floor frame?
A. Make sure that the shed is level and square, with the correct floor frame size, and that the corner panels are
installed correctly. Line up the large hole in the panel with the small holes in the floor frame. An awl can be used to
help align the holes.
Q. How do I align the holes in the roof panels with the holes in the roof beam and side wall angles?
A. Your building must be level and square in order for the holes to align. It must be square at both the top and
bottom. Check that the building is square by measuring diagonally. The two diagonal measurements will be equal.
If your building is out of square, carefully rock and push the shed until it is square. Also, try loosening the roof
beams to give more play and flexibility. Non-alignment can also occur if your building is not level. You can raise
corners and shim under them to make it level. Check that the panels are installed in the proper location. The
building should not be permanently anchored until the complete unit is assembled; otherwise, you will not be able
to make adjustments for squareness during assembly. Do not attach the bottom of the roof panels to the side wall
angles until all the roof panels are up.
Note: If you have to stop assembly for any reason before it is complete, do not leave your unfinished construction
without first temporarily anchoring the corners of the shed to your base and placing weights, such as patio blocks
or sandbags, on the floor frame.
Q. What kind of customer support is available?
A. Our instruction manuals contain step-by-step assembly illustrations and guide you from preparation through
assembly to care and maintenance of your finished building. Each part is marked with a factory number for easy
identification. In addition, our assembly animation (located under the Customer Support menu at www.arrowsheds.
com) provides helpful tips. But if you need to reach someone at Arrow, you can contact Arrow Customer Service,
toll free, at 1-800-851-1085 (press 1) or via e-mail at [email protected]. Have your model number and
instruction manual with you when you call.
5
Q. What if the rear wall angle and channels are too large to fit inside of the rear wall panels?
A. Check the dimensions of wall assemblies. They should be slightly smaller than the floor
06A
frames. Lay the
assemblies on top of the rear floor frame and pull them up to the top of the wall panels causing the corner panels
to stand erect and not lean inward. Caution: Be careful to not scratch the panels on the way up.
Q. The wide rib always overlaps the crimped rib. Is there ever an exception?
A. This sequence is to be followed through the assembly process. However, this will typically happen once on the
rear and once on each side wall (vertical wall units only) where there will be either two crimped ribs overlapping or
two wide ribs overlapping. This may give it a tighter fit, but it will work.
Q. Can the building be painted?
A. The buildings can be painted with an exterior-grade paint designed for use on steel. Contact your local paint
supplier for recommendations.
Q. I heard that rust might be an issue with steel; is it?
A. While steel can rust, with proper care this should not be an issue. For a long-lasting finish, periodically clean
the exterior surface and apply spray-on car wax. Touch up scratches as soon as you notice them by immediately
cleaning the area with a wire brush or emery paper, washing it and applying touch-up paint. This will minimize rust
and maintain your shed’s attractive appearance for years.
Q. How do I take care of dents in my shed?
A. Proper selection of shed size, including a sufficient door-opening width, and proper placement of your shed
should minimize the possibility of damage. If a dent does occur, carefully push the dent out from the opposite side.
If the paint has been scratched or removed, touch up the area as soon as you notice it. Immediately clean the area
with a wire brush or emery paper, wash it and apply touch-up paint. This will minimize rust and maintain your shed’s
attractive appearance for years.
Still have questions? Visit us online at www.arrowsheds.com to view lots of helpful tips and information
regarding all of our available products. You can also contact our Customer Service team at 1-800-851-1085
(press 1), or via e-mail at [email protected].
Part No.
#####
5
At the top of each page you will see one or more Part
Cues like the one to the left. These Part Cues are
designed to help you quickly identify the parts needed
for each step.
Quantity Needed
End View
Part Name
Part Name
Confirm that all hardware and parts are
present before attempting to assemble
your building.
Part Numbers
For missing or damaged parts contact
Customer Service. Do not return to store.
Customer Service:
1-800-851-1085
or
[email protected]
Part Number
1. Each part has an identifying part number on it.
2. Part Numbers are referenced in each step.
3. Unpainted parts have a stamped in number and painted
parts have a number that is inked on.
Remove inked on numbers with soap and water after assembly.
6
HARDWARE LIST...
Key Part
No. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
65103
65923-61
65923-62
65923-06
65004-61
65004-62
65958
66783
66692
66646
66809
66054
66609
66183L
66183R
67545
66447
Part
Description
Qty.
Hex Nut (#8-32)
Small Bolt (Stone) (#8-32 x 3/8) (10 mm)
Small Bolt (Vanilla) (#8-32 x 3/8) (10 mm)
Small Bolt (Black) (#8-32 x 3/8) (10 mm)
Small Screw (Stone) (#8AB x 5/16) (8 mm)
Small Screw (Vanilla) (#8AB x 5/16) (8 mm)
Long Bolt (#8-32 x 7/8) (22 mm)
Flat Head Bolt (#8-32 X 1/2) (13 mm)
Tapping Screw (#10ABx1) (25 mm)
Washer Sheet
Locking Handle Right
Latch
Hinge
Left Roof Trim Cap
Right Roof Trim Cap
Weather Stripping
Peak Cap
152
74
40
14
384
66
4
24
2
7
1
1
4
2
2
1
2
18 67236
Adhesive Pads (2 per sheet)
1
19 66684
Top Latch Spring
1
20 66808
Bottom Latch Spring
1
21 66810
Left Handle
1
22 66811
Handle Backplate
2
23 66812
Hinge Plate Decoration
4
24 6228
25 66859
Track Support
Craftsman Logo
2
1
Hardware Views by Key No.
List
Various fasteners are used The fasteners used in each
throughout the construction of your step are shown actual size at
storage unit. In each step you will the top of each page. If you are
see the abbreviations listed below unsure which fastener to use,
used in the illustrations to help you hold it up to the picture and use
identify which fastener to use.
the one that matches.
SB - Stone Bolt
VB - Vanilla Bolt
BB - Black Bolt
SS - Stone Screw
VS - Vanilla Screw
FB - Flat Head Bolt
QTY 18
TS - Tapping Screw
LNB - Long Bolt
7
07CI
1
2
11/32 Hex.
4
BB
#2 Phillips
SB
#2 Phillips
5
SS
#2 Phillips
7
LNB
#2 Phillips
VB
#2 Phillips
6
VS
#2 Phillips
8
FB
#2 Phillips
TS
9
3
10
#2 Phillips
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PARTS LIST...
Key
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Part No.
5284
5285
5287
10778
8364
10786
6634
8189
9704
9703
9204
10702
10707
10718
10719
10720
10721
10780
10782
9344
10773
10774
10784
9338
10779
10775
10703
8827
10708
80069
80067
9339
10827
11044
9009
9496
10834
80125
9702
10777
69835
Part Description
Right Corner Post
Left Corner Post
Rear Splice Post
Roof Beam
Side Roof Trim
Ridge Cap
Gable Brace
Shelf Bracket
Right Gable, Rear
Left Gable, Rear
Roof Beam Brace
Ramp
Front Inner Header
Horizontal Door Brace
Door Handle Brace
Diagonal Door Brace
Door Stop
Right Door Jamb
Door
Siding Stud
Side Siding
Right Roof Panel
Side Floor Frame
Right Rear Wall Angle
Side Wall Angle
Rear Siding
Front/Rear Floor Frame
Front Siding
Front Outer Header
Left Door Jamb
Left Roof Panel
Left Rear Wall Angle
Door Jamb Angle
Right Gable, Front
Gable Brace
Gable Brace
Front Wall Channel
Left Gable, Front
Roof Panel
Roof Beam
Edge Trim (Green)
Qty.
2
2
1
8
2
1
4
4
1
1
2
1
1
4
2
8
1
1
2
24
6
2
2
1
2
6
4
6
2
1
2
1
2
1
2
4
2
1
2
2
4
68
08CI
List
Selected End Views by Key No.
1&2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
20
23
24&32
25
27
29
30
33
35
37
40
41
ASSEMBLY BY KEY NO.
NOTE: Double Wall
Studs are used on
side and back walls to
support Siding Panels.
09R
24
25
32
29
21
8
20
20
2
25
8
28
Walls
1
26
13
29
26
26
21
3
2
21
28
37
26
21
26
28
30
21
33
28
33
18
37
27
23
26
28
1
21
28
27
27
12
23
Floor
27
9
ASSEMBLY BY KEY NO.
5
31
39
6
22
Roof
4
4
36
7
38
7
39
9
31
4
4
41
22
41
36
35
11
10CI
40
40
11
35
4
4
4
5
10
7
41
36
4
7
34
36
41
14
14
19
19
16
16
16
15
17
16
16
16
14
Doors
10
16
15
16
14
ASSEMBLY OVERVIEW
11CI
Build the Floor Frame
Erect Post, Studs, and Door Jambs
Install Siding Panels
Attach Gables and Roof Beams
Install Roof Panel, Ridge Cap,
Side Trim, Corner Cap
Install Doors
Shed is now complete.
11
CONSTRUCTING A BASE...
12R
No matter which of the options below you choose for a base, an ARROW ANCHORING KIT is
recommended as an effective method of properly securing your building after assembly is complete.
OPTION 1: Directly on ground (earth)
Assemble your building directly on level ground (grass, dirt, rock, sand, etc.). If you choose this option Craftsman has a simple kit
available to provide a floor inside the shed to keep stored items off the ground. This kit can be used to support a plywood floor (wood
not included) or be filled with sand/rock to provide a solid surface. (Sears Order No. 68384 (CFBS109))
Allow 1 - 2 hours for construction.
OPTION 2: Wood Platform
If you decide to build your own base, be sure to select the appropriate materials.
These are the recommended materials for your base:
• 2 x 4's (38 mm x 89 mm) Pressure Treated Lumber • 5/8" (15,5 mm) 4 x 8 (1220 mm x 2440 mm) Plywood-exterior grade
• 10 & 4 penny Galvanized Nails • Concrete Blocks (optional)
NOTE: Pressure Treated Lumber must not be used where it will make contact with your storage building. The properties of
Pressure Treated Lumber will cause accelerated corrosion. If Pressure Treated Lumber comes in contact with your storage
building your warranty will be voided.
The platform should be level and flat (free of bumps, ridges etc.)
to provide good support for the building. The necessary materials
may be obtained from your local lumber yard.
16
6 c "/24"
m/6
1,0
c
40,
m
To construct the base follow instructions and diagram.
Construct frame (using 10 penny galvanized nails)
Measure 16"/24" (40,6 cm/61,0 cm) sections to construct
inside frame (see diagram)
Secure plywood to frame (using 4 penny galvanized nails)
1
307 21"
,3 c
m
FRONT
(DOOR)
Allow 6 - 7 hours for construction.
OPTION 3: Concrete Slab
The slab should be at least 4" (10,2 cm) thick. It must be level
and flat to provide good support for the frame.
The following are the recommended materials for your base.
• 1 x 4's (19 mm x 89 mm) (will be removed once the concrete cures)
• Concrete • Sheet of 6 mil plastic
• We recommend for a proper strength concrete to use a mix of:
1 part cement • 3 parts pea sized gravel • 2 1/2 parts clean sand
"
81 cm
,7
05
2
Note: Platform/Slab will extend 9/16" (1,4 cm) beyond
floor frame on all four sides. Seal this 9/16" (1,4 cm)
of wood with a roofing cement (not included), or bevel
this 9/16" (1,4 cm) of concrete when pouring, for good
water drainage.
Prepare the Site/Construct a Base
1. Dig a square, 6" (15,2 cm) deep into the ground (remove grass).
2. Fill up to 4" (10,2 cm) in the square with gravel and tamp firm.
1
30 21"
3. Cover gravel with a sheet of 6 mil plastic.
"
7,3
81 cm
cm
4. Construct a wood frame using four planks of 1x4 (19 mm x 89 mm) FRONT
,
57
lumber.
20
(DOOR)
5. Pour in concrete to fill in the hole and the frame giving a
total of 4" (10,2 cm) thick concrete. Be sure surface is level.
Note: Finished Slab dimensions, with lumber removed.
Allow 3 - 5 hours for construction and a week for concrete curing time.
12
Step 1:
You will need for this page:
SB
Floor Frame Pre-Assembly
Washers are to be
used on painted
parts only. Washers
are not necessary on unpainted
parts and there are not enough
to use on every Screw and Bolt.
10703 4
Front/Rear
Floor Frame
(QTY: 8)
1
13R
Join two (2) Front/Rear Floor Frames together by overlapping them as shown and secure the
Frames with four (4) Stone Bolts and Nuts. Repeat this for the other two (2) Front/Rear Floor
Frames.
10703
10703
BUILD TWO (2) ASSEMBLIES
2
Check the overall length of each set of Floor Frames to make sure they are at the proper length
of 119 3/8” (303,2 cm).
119 3/8
”
(303,2
6
13
cm)
Step 2: Frame Pre-Assembly
14R
You will need for this page:
SB
(QTY: 1)
1
SS
(QTY:2)
9339
Left Rear
Wall Angle
1
9338
Right Rear
Wall Angle
1
10707 1
10708 2
Front Inner
Header
Front Outer
Header
Connect the Front Inner Header to a Front Outer Header using one (1) Stone Screw as
shown. Repeat this for the opposite end.
10708
10708
SS
10707
10707
Header
118 1/8” (300,0 cm)
10708
2
SS
Join the Left and Right Rear Wall Angles using one (1) Stone Bolt and Nut as shown.
9339
9338
SB
Rear Wall Angle
118 1/8” (300,0 cm)
3
Check the overall length of the Header and Rear Wall Angle sets to make sure they are at the
proper length of 118 1/8” (300,0 cm).
6
14
Step 3: Stud Assembly
You will need for this page:
SS
(QTY:72)
1
9344 24
Siding Stud
Join two (2) Siding Studs together using six (6) Stone Screws as shown.
BUILD TWELVE (12) ASSEMBLIES
9344
9344
Top view of Siding Studs.
35 9/16”
(90,3 cm)
2
Repeat process to make eleven (11) more assemblies.
Set assemblies aside for later use.
6
15
15R
Step 4: Roof Beam Assembly
16R
You will need for this page:
SB
Roof Beam
(QTY: 20)
1
10778 8
10777 2
Roof Beam
Place two (2) 2” (5,1 cm) Roof Beams back-to-back with small holes on top. Fasten together
using four (4) Stone Bolts and Nuts. DO NOT FULLY TIGHTEN.
BUILD FOUR (4) ASSEMBLIES
End view of Roof Beam
10778
10778
2
Repeat process to make three (3) more assemblies.
Set assemblies aside for later use.
3
Place two (2) 4” (10,2 cm) Roof Beams back-to-back with small holes on top. Fasten together
using four (4) Stone Bolts and Nuts. DO NOT FULLY TIGHTEN. Set assembly aside for later
use.
10777
10777
6
16
Side of Beams with small holes must face up.
Step 5: Door Pre-Assembly
You will need for this page:
1
TS
SS
(QTY: 2)
(QTY: 24)
10782 2
Door Panel
10718 4
Horizontal
Door Brace
2
Start assembly by sliding the Door Handle
Brace into the middle of the Door and securing
it with four (4) Stone Screws. Then attach the
Horizontal Door Braces to each end of Door
using two (2) Stone Screws on each brace.
Once installed, attach Adhesive Pad between
leg of Door Handle Brace and Door.
10718
10719 2
Door Handle
Brace
10720 8
67236 2
Diagonal Door
Brace
Adhesive Pad
17P
Place the ends of Diagonal Door Braces with
small holes under Horizontal Door Braces
as shown. Secure all Diagonal Door Braces
to center of Door Handle Brace using one
(1) Tapping Screw. Attach all Diagonal
Door Braces under Horizontal Door Braces
using four (4) Stone Screws at each corner
as shown.
Make sure holes in Door Handle Brace
are on same side as holes in Door.
10719
67236
10720
10720
10782
10719
TS
107
10782
20
Large holes of Diagonal
Door Braces go to center.
10720
10720
107
18
10718
3
Repeat this process for the other Door.
Diagonal Door Braces attach from behind
Horizontal Door Brace.
6
17
Step 6: Right Door Assembly
You will need for this page:
FB
LNB
(QTY: 2)
(QTY: 6)
BB
(QTY: 6)
66609 2
Hinge
66809 1
66054 1
Locking
Handle Right
Latch
18P
66811 1
Handle
Backplate
66812 2
Hinge Plate
Decor
66609
FB
1
Attach Hinges to Door using
six (6) Flat Head Bolts.
2
Install Locking Handle and
Handle Backplate using
two (2) Long Bolts. Secure
Backplate using two (2)
Black Bolts and Nuts.
3
Attach Latch
Handle.
4
Tighten set screws in Latch.
to
66811
Locking
BB
66809
LNB
BB
66054
66812
5
BB
6
18
Attach Hinge Plate Decor to Door
by the Hinges using two (2) Black
Bolts and Nuts for each Decor.
When securing the Decor, be careful not to
scratch the paint. Do not use a drill to tighten the
Nuts. Instead, use a No. 2 Phillips Screwdriver
to hold the Bolt in place and a Nut Driver or
Wrench to tighten the Nut.
Step 7: Left Door Assembly
You will need for this page:
FB
LNB
(QTY: 2)
66609 2
(QTY: 6)
Hinge
BB
66810 1
Left
Handle
66811 1
Handle
Backplate
19P
66812 2
Hinge Plate
Decor
(QTY: 6)
1
Attach Hinges to Door using six
(6) Flat Head Bolts.
2
Install Locking Handle and
Handle Backplate using two (2)
Long Bolts. Secure Backplate
using two (2) Black Bolts and
Nuts.
Attach Hinge Plate Decor to Door
by the Hinges using two (2) Black
Bolts and Nuts for each Decor.
3
66609
FB
66811
BB
66810
LNB
BB
When securing the Decor, be careful not to
scratch the paint. Do not use a drill to tighten
the Nuts. Instead, use a No. 2 Phillips
Screwdriver to hold the Bolt in place and a
Nut Driver or Wrench to tighten the Nut.
66812
BB
6
19
Step 7: Continued
You will need for this page:
SS
(QTY: 8)
66808 1
Bottom
Latch Spring
4
Remove two (2) Screws from left
side of Door Handle Brace and
far left Screw from both top and
bottom Horizontal Door Brace.
Screws will be reused.
5
Attach Door Stop and both Top
and Bottom Latch Springs to
left side of Door using the four (4)
previous Screws as well as eight
(8) additional Stone Screws.
10721 1
66684 1
Door Stop
Top Latch
Spring
20P
66684
Remove far left Screw from
top and bottom Horizontal
Door Brace to install Door
Stop and Latch Springs.
10721
Remove Screws to
install Door Stop.
66808
6
20
Step 8: Floor Assembly
You will need for this page:
SS
10784 2
Assemblies from Step 1:
•
(QTY: 8)
21R
Floor Frame Assemblies (2)
Side Floor
Frame
The remainder of the building assembly requires many hours and more than
one person. Do not continue beyond this point if you do not have enough time
to complete the assembly today. A partially assembled building can be severely
damaged by light winds.
1
Assemble the four (4) corners of the Floor Frame using two (2) Stone Screws at each corner as
shown.
10784
10784
Overlap Floor Frames as shown.
Set Floor Frame with large holes
on top at each corner.
2
Measure the Floor Frame diagonally. When the diagonal measurements are equal, the Floor
Frame is square.
Level
The Floor Frame must be BOTH square AND
level or the holes will not line up properly.
6
21
Step 9: Posts/Frame
You will need for this page:
SS
Right Corner
Post
(QTY: 22)
1
2
5284
2
5285
Left Corner
Post
10779 2
Side Wall
Angle
Position Right and Left Corner Posts
at the corner of the Floor Frame as
shown. The angled end of each Post
must be placed on top of all four (4)
corners. Fasten the Corner Post to
the Floor Frame using two (2) Stone
Screws in each Post.
22R
Assemblies from step 2:
•
•
Header Assembly (1)
Rear Wall Angle
Assembly (1)
5284
5285
The Floor Frame must be square
and level or holes will not align.
5285
Support the Corner Posts with
stakes or other devices until
Door Jambs are attached.
5284
Long leg of Rear Wall Assembly
and Side Wall Angles faces
down.
Re
ar
10779
He
ad
er
As
Wa
ll
An
gle
2
As
sem
3
bly
sem
bly
4
10779
Fasten Header Assembly to top of front
Corner Posts through top holes using two
(2) Stone Screws.
Fasten Rear Wall Angle Assembly to top
of back Corner Posts using two (2) Stone
Screws in each Post.
Fasten Side Wall Angles to top of side
Corner Post using two (2) Stone Screws
in each Post.
Side Wall Angle on top
Fro
nt
Leg of Header Assembly
to inside of building and
faces down.
Wall Angles must face inside
building.
6
22
Step 10: Splice Post/Door Jamb
23P
You will need for this page:
10780 1
SS
SB
(QTY: 4)
Right Door
Jamb
(QTY: 6)
SS
1
80069 1
Left Door
Jamb
5287
1
Rear Splice
Post
(QTY: 4)
Position Splice Post at the center of the
rear wall and fasten using two (2) Stone
Screws into rear Floor Frame and four
(4) Stone Bolts and Nuts into Rear Wall
Angle Assembly.
5287
SB
Support the Corner
Posts with stakes or
other devices until Door
Jambs are attached.
5287
5287
Rear
SS
SS
2
Align top hole on notched side of one (1)
Door Jamb with hole closest to center
on the Header. Fasten Door Jamb to
the Header and Frame using four (4)
Stone Screws in Door Jamb. Repeat
for other Door Jamb.
80069
Add Washers to
Screws on holes
closest to center.
10780
SS
SS
10780
SS
SS
Front
Notched edge must
face center of building.
6
23
SS
SS
Step 11: Studs
You will need for this page:
10834 2
SS
SS
(QTY: 2)
(QTY: 16)
Assemblies from step 3:
•
Front Wall
Channel
24R
Stud Assemblies (12)
1
Following dimensions, measuring from the end of angle, position a Stud Assembly inside top
angle and fasten with one (1) Stone Screw through the lower hole of angle.
2
Place bottom of Stud Assembly over Floor Frame as shown. Do not fasten bottom at this
time. Repeat procedure for the remaining Stud Assemblies around the building.
3
Place Front Wall Channels into poisiton behind Corner Post and Door Jamb. Fasten using
three (3) Stone Screws as shown below.
49
59
39
,0 c
150
”(
6
1/1
m)
9”
2c
9,
” (9
6
1/1
m)
29
3/8
” (1
3/1
6”
(22
,9
25
,4
(74
,1
cm
)
cm
)
cm
Inside
)
19 1/16”
(48,4 cm)
Outside
10834
Washer
10834
Do not fasten
at this time.
6
24
Step 12: Side Siding
You will need for this page:
SS
(QTY: 24)
Washers are to be used on painted
parts only. Washers are not necessary
on unpainted parts and there are not
enough to use on every Screw and Bolt.
10773 6
VS
25R
Side Siding
(QTY: 36)
1
Slide bottom Side Siding into channels of Corner Posts as shown. Once in place, secure with
five (5) Vanilla Screws. Screws going into bottom Floor Frame also secure Stud Assemblies.
2
Slide remaining Panels into channel, making sure Siding Panels overlap as shown. Once
overlapped, fasten Panels using five (5) Vanilla Screws as before.
3
Secure both top Panels to Side Wall Angle using an additional three (3) Vanilla Screws per
Panel.
4
From inside building, fasten all Side Siding Panels to Corner Posts using four (4) Stone Screws
per Panel.
10773
10773
Be certain all Siding Panels are
completely overlapped or holes
will not line up.
10773
10773
SS
SS
10773
Fasten all Panels from
inside with four (4) Stone
Screws per Panel.
10773
VS
VS
6
25
VS
Screws also secure
Stud Assemblies to
Floor Frame.
Step 13: Rear Siding
You will need for this page:
SS
(QTY: 24)
VS
(QTY: 30)
26R
10775 6
Rear Siding
1
Slide bottom Rear Siding Panels into channels of Corner Posts and Splice Post as shown.
Once in place, secure with four (4) Vanilla Screws per Panel. Screws going into bottom Floor
Frame also secure Stud Assemblies.
2
Slide remaining Panels into channels, making sure Siding Panels overlap as shown. Once
overlapped, fasten each Panel using four (4) Vanilla Screws as before.
3
4
Secure the tops of Panels to Rear Wall Angle using an additional three (3) Vanilla Screw per
Panel.
From inside building, fasten all Rear Siding Panels to Corner Posts and Splice Post using four
(4) Stone Screws per Panel.
Be certain all Siding Panels are
completely overlapped or holes
will not line up.
10775
10775
10775
10775
VS
10775
VS
SS
10775
Screws also secure
Stud Assemblies to
Floor Frame.
SS
6
26
Step 14: Front Siding
You will need for this page:
SS
(QTY: 24)
1
8827
27R
6
Front Siding
Slide Front Siding into channels of Corner Posts and Door Jambs as shown. Once in place,
secure Panels from inside the building to the Corner Posts and Door Jambs using four (4)
Stone Screws per Panel.
8827
Be certain all Siding Panels are
completely overlapped or holes
will not line up.
8827
8827
8827
8827
8827
Inside
6
27
Step 15: Gables
You will need for this page:
VB
9704
2
Right Gable
(QTY: 16)
9703
Left Gable
2
6634
28R
4
Gable Brace
9496
4
Gable Brace
69835 4
Edge Trim
GABLES ARE STACKED TOGETHER
DURING SHIPPING AND MAY BE
MISTAKEN FOR ONE GABLE! SEPARATE
GABLES BEFORE CONTINUING.
Edge Trim (Plastic)
Install Edge Trim to cover Gable Edge
BEFORE doing ANY work with Gables.
Failure to do so could result in injury.
1
Attach a short and long Gable Brace to all four (4) Gables using two (2) Vanilla Bolts and Nuts
for each Brace as shown below.
9496
6634
9704
9703
6634
9496
Leg of Roof Beam Bracket must face center of Gable as shown.
6
28
Step 15: Continued
You will need for this page:
SS
SB
(QTY: 32)
2
(QTY: 5)
9009
2
67545 1
Weather
Stripping
Gable Brace
6228
29R
2
Track Support
Working one (1) Gable at a time, lift Left and Right Gables into place on top of Rear Wall
Angle. Gables must go under Side Wall Angles. Secure using seven (7) Stone Screws and
one (1) Stone Bolt per Gable.
Back Gables
SB
Front Gables
Leave hole open
Gables must go under
Side Wall Angles.
3
4
5
Working one Gable at a time, lift Left and Right Gables into place on top of
Header. Gables must go under Side Wall Angles. Secure using seven (7)
Stone Screws per Gable. Do not insert Screws into the two (2) holes closest
to the peak of each Gable. These will be used to attach the Track Support
later.
Join Left and Right Gables together using Gable Brace and securing
with one (1) Stone Bolt and Nut in the second hole from the bottom. Apply
Weather Stripping along the mating edge of the Left and Right Gable as
shown. Cut the Weather Stripping to length. Repeat for opposite side.
Position Track Support as shown. Secure Track Supports to Gable using
one (1) Stone Bolt. Secure to Header using two (2) Stone Screws per side.
Top View of Gables
SB
Attach Brace with Bolt thru
second hole from bottom only.
Tape should wrap
around gap between
Gables.
Weather Stripping Tape
6
29
Install Track Support.
Step 16: Roof Beams/Braces
30R
You will need for this page:
Assemblies from step 4:
SB
•
Roof Beam Assembies (5)
(QTY: 20)
1
Side of Beams with small
holes must face up.
Secure the Roof Beam Assemblies
to the Gables as shown using two (2)
Stone Bolts and Nuts on each end of
each Roof Beam Assembly.
Spread two (2) halves
of Roof Beams
10778
10778
10777
10778
10778
IMPORTANT:
At this time, take a moment to
ensure the building is level and
square. Measure the building diagonally again to make sure the
building is square. The building should be square at the base
and at the top. This will make Roof Panels fit better and holes will
better align.
6
30
Step 16: Continued
You will need for this page:
31R
9204 2
SB
(QTY: 4)
Beam Brace
In the front, attach the Roof Beam
Brace to the Track Support with one
(1) Stone Bolt and Nut as shown
and rotate to align with Roof Beam. Secure
to Roof Beam with one (1) Stone Bolt and
Nut as shown.
2
3
In the rear, attach the Roof Beam
Brace to the Gable with one (1)
Stone Bolt and Nut as shown and
rotate to align with Roof Beam. Secure to
Roof Beam with one (1) Stone Bolt and Nut
as shown.
Tab end attaches to Roof Beam.
In Front, attach Brace to Track Supports and Main Beam.
Angled end attaches to Gable.
Attach Brace to Gable then rotate to align with Roof Beam.
In Rear, attach Brace to lowest hole in Gable and Main Beam.
31
Step 17: Roof Assembly
You will need for this page:
SS
VB
(QTY: 12)
(QTY: 24)
80067 1
10774 1
Left Roof
Panel
Right Roof
Panel
67545 1
Weather
Stripping
1
2
Attach Back Right Roof Panel to Top Roof Beam only using
four (4) Stone Screws.
3
Continue fastening Roof Panel to Gable and Lower Roof
Beams using six (6) Vanilla Bolts and Nuts and eight (8)
Stone Screws. Do not fasten to Side Wall Angle at this time.
4
5
32CI
Don’t focus weight
on roof!
Remove Edge Trim from the Left Gable under the Roof
Panel.
Install Back Left Roof Panel.
Work one corner at a time. Be sure
to finish a corner before moving on to
the next one.
While installing Roof Panels use Weather
Stripping Tape to seal roof ridge.
Front
Follow the fastener
sequence shown for
proper alignment.
4
3
14
13
12
11
18
17
16 10774
15
Tape
in a
along
roof.
VB
7
VB
VB
VB
10
1
80067
VB
VB
Weather Stripping
should be applied
continuous strip
the length of the
2
6
5
Back
8
Uncrimped Rib
9
Crimped Rib
Whenever a crimped rib and an uncrimped rib meet,
place the crimped rib UNDER the uncrimped rib.
6
32
`
Step 17: Continued
You will need for this page:
SS
(QTY: 24)
9702
SB
2
67545 1
Weather
Stripping
RoofPanel
(QTY: 2)
33CI
6
Attach two (2) Roof Panels, one at a time, to Roof Beams using
twelve (12) Stone Screws.
7
Secure Roof Panels to Back Roof Panels using one (1) Stone
Bolt and Nut per Panel as shown below.
8
Continue installing Weather Stripping Tape to seal roof ridge.
Don’t focus weight
on roof!
Front
SB
9702
9702
10774
80067
Back
6
33
`
Step 17: Continued
You will need for this page:
SS
SB
80067 1
10774 1
66859 1
Left Roof
Panel
Right Roof
Panel
Craftsman
Logo
(QTY: 2)
(QTY: 48)
VB
34CI
67545 1
Weather
Stripping
BB
(QTY: 12)
Don’t focus weight
on roof!
(QTY: 2)
9
Attach Front Left and Right Roof Panels, one at a
time, to Roof Beams using twelve (12) Stone Screws
per Panel.
10
Insert Stone Bolt and Nut in middle hole where ribs
overlap.
11
Secure Front Roof Panels to Gables using six (6)
Vanilla Bolts and Nuts per Gable as shown below.
12
Attach Craftsman Logo to Gables using two (2) Black
Bolts and Nuts (w/washers) as shown below.
10774
SB
80067
9702
SB
9702
80067
VB
10774
VB
VB
VB
66859 BB
VB
VB
BB
VB
VB
13
Fasten the lower end of the Roof Panels to the Side
Wall Angles using four (4) Stone Screws per Panel.
6
34
VB
VB
VB
`
Step 18: Ridge Cap/Roof Trim
35CI
You will need for this page:
SS
SS
(QTY: 4)
(QTY: 4)
SB
10786 1
8364
Ridge Cap
Side Roof
Trim
2
66183 2
Left Corner
Cap
2
3
Right Corner
Cap
66447 2
Peak Cap
Don’t focus weight
on roof!
(QTY: 8)
1
66183 2
Fully tighten Bolts and Nuts on Roof Beams.
Install Peak Caps and Ridge Cap using eight (8) Stone
Bolts and Nuts as shown.
Install Side Roof Trim and Right and Left Corner Caps
using eight (8) Stone Screws as shown.
SB
SS
SB
66447
66183
SS
SB
10786
SB
8364
SS
SS
SS
66183
66447
SS
8364
SS
SS
66183
6
35
66183
`
Step 19: Door Installment
36CI
You will need for this page:
SS
FB
(QTY:12)
(QTY:4)
10702 1
10827 2
Assemblies from step 5:
•
•
Door Jamb
Angle
Ramp
Right Door Assembly (1)
Left Door Assembly (1)
NEED AT LEAST TWO PEOPLE
TO PERFORM THIS STEP!
1
Place the Door Jamb Angles behind the Door Jambs. Using three (3) Flat Head Bolts
and Nuts per Door Hinge, secure Doors and Door Jamb Angles to Door Jambs.
End View
Door Jamb Angle
FB
Door Jamb
Hinge
FB
FB
SS
SS
10702 SS
2
Fasten Ramp to Floor Frame using four (4)
Stone Screws.
6
36
`
Step 20: Shelf Brackets
You will need for this page:
SS
8189
38R
4
Shelf Bracket
(QTY:8)
1
Choose which sides and Studs to mount the Shelf Brackets on. Shelf Brackets can be installed
on side and / or rear walls. If installing on rear wall, Shelf Brackets must be placed on adjacent
Studs.
2
Attach a Shelf Bracket to a Stud using two (2) Stone Screws as shown below. Repeat this for the
other Shelf Brackets.
9344
Shelf Brackets can be
installed on either side wall
or either back wall section.
8189
VARIOUS LOCATIONS OF SHELVING SYSTEMS
FASTEN SHELF TO BRACKET
Makes 8” to 12” (20,3-30,5 cm)
wide shelves in any length.
Keep this Owner’s Manual and Assembly
Instructions for future reference.
6
37
ANCHORING OPTIONS...
43A
IMPORTANT:
•
•
•
•
If you have swing doors, they must hang and swing level before anchoring building.
Anchor your building at this time. See below for details on anchoring.
If you have purchased a Floor Frame Kit, you should install it at this time.
Please take a moment to ensure that the building is installed in accordance
with these instructions and with all applicable regulations.
Anchoring Down The Building
The entire floor frame MUST be securely anchored once the building is erected.
Below are recommended ways of anchoring.
Anchoring into Wood/Post:
Arrow Anchoring Kit: (Model No. AK4 or 60298)
Use 1/4" (6 mm) Wood Screws. There are 1/4" (6 mm)
dia. holes provided in the frames for proper anchoring.
Recommended for use with any suggested base.
Contains: 4 Anchors with Cable, Clamps and
installation instructions.
1.
2.
OVER THE BEAMS
AND INTO THE GROUND
Anchoring into Concrete:
Arrow Anchoring Kit: (Model No. AK100 or 68383)
Recommended for use with the concrete base.
Contains: Corner gussets, perimeter clips, hardware,
1/4" masonry drill bit and installation instructions.
1. For poured concrete slab or footing or patio blocks:
Use 1/4" x 2" (6 mm x 51 mm) Lag Screws.
2. For Anchor Post of Concrete poured after building is
erected: Use 1/4" x 6" (6 mm x 152 mm) Lag Screws.
1.
An Anchor Kit may be purchased online at www.arrowsheds.com
You can also purchase one over the phone by calling 1-800-851-1085.
See accessories page for details.
38
2.
CARE & MAINTENANCE...
35P
Exterior Care:
For a long lasting finish, clean and wax the exterior surface. We recommend washing with a mild soap solution. DO
NOT use power washing to clean your shed. Using a spray automotive type wax periodically on the exterior is highly
recommended if you are in a high humidity or coastal climate region.
Combustibles and corrosives must be stored in air tight containers designed for chemical and/or combustible
storage. Corrosive chemicals such as fertilizers, pesticides and herbicides should be cleaned off the interior and
exterior surfaces immediately. Rust caused by chemical damage is not covered by the warranty.
DO NOT STORE POOL CHEMICALS IN YOUR SHED - THIS VOIDS YOUR WARRANTY
Rust protection precautions may help to stop rust from developing, or stop it quickly as soon as it appears.
• Avoid nicking or scraping the coating surface, inside and out.
• Keep roof, base perimeter and door tracks free of debris and leaves which may accumulate and retain moisture.
These can do double damage since they give off acid as they decay.
• Touch up scrapes or nicks and any area of visible rust as soon as possible. Make sure the surface is free of
moisture, oils, dirt or grime and then apply an even film of high quality touch-up paint.
• Various paint manufacturers provide products for rust treatment and coverage. If surface rust does appear on
your shed we recommend treating those areas as soon as possible, following the paint supplier of your choice
instructions.
• Our customer service department can provide the paint tinting formula for matching the color of your shed. We also
have touch-up paint available for repairing small nicks and scratches.
Roof:
Keep the roof clear of leaves and snow. Heavy amounts of snow on the roof can damage the building making it
unsafe to enter.
Doors:
Keep doors closed and locked to prevent wind damage.
Fasteners:
Use all washers supplied to protect against weather infiltration and to protect the metal from being scratched by
the screws. Regularly check screws, bolts, nuts, etc., and retighten as necessary.
General:
• A plastic sheet (vapor barrier) placed under the entire floor area may reduce condensation.
• Wash off inked part numbers on coated panels with soap and water.
• Silicone caulking may be used for watertight seals throughout the building.
Please note, Manufacturer cannot be held responsible for any consequences due to buildings that are not installed
per these instructions, or for damage due to weather conditions or acts of God.
Keep these assembly instructions and owner’s manual for future reference.
39
Warranty...
36P
CRAFTSMAN 20 YEAR LIMITED WARRANTY
FOR TWENTY YEARS from the date of purchase, this product is warranted against defects in material and
workmanship when product is installed, operated and maintained according to all supplied instructions. With proof
of purchase, a defective part will be replaced free of charge.
For warranty coverage details to obtain free part replacement, call the following toll-free number: 1-800-851-1085
All warranty coverage excludes part paint loss, discoloration, corrosion or surface rusting, which are conditions that
can be the result of normal use, accident or improper maintenance.
This warranty does not apply to a product that is damaged or altered through misuse, abuse, accident, neglect,
modification or mishandling.
Disclaimer of implied warranties; limitation of remedies
Customer’s sole and exclusive remedy under this limited warranty shall be part replacement as provided herein.
Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to twenty
years or the shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some
states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitation
on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply
to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
40
01Q
Assembly Guide
Accessorize Your Shed...
VersaTrack™ Trackwall
Wall Organization System
SOLD SEPARATELY AT SEARS
41
Trackwall Assembly
You will need for this assembly:
• #10 x 1” (2,5 cm)
length or
5 mm Screws
(6 per trackwall)
(QTY: 6)
1
Trackwall
02Q
Tools Required:
•
•
•
•
Pencil
• Screwdriver
Level
• Countersink
Drill
• Tape Measure
1/8” (3 mm) Drill Bit
SAFETY WARNINGS
AND CAUTIONS
8x5
• Read and follow all Safety Warnings and installation
instructions before use of this product.
Trackwall
Trackwall
• Failure to follow Warnings and Instructions, which
includes exceeding the stated load ratings on the
Trackwall, may cause product to fail, resulting in
personal injury or property damage.
• Follow mounting instructions appropriate for this
Front
type of wall surface. Failure to do so will reduce the
Trackwall’s capacity.
• Be sure to use appropriate safety equipment when
using power and hand tools.
• Install Trackwall using appropriate hardware, and in
Trackwall
accordance with local building codes.
• Trackwall must be mounted level.
• DO NOT mount Trackwall on ceiling.
10x7
See diagrams to right for reference
as to where Trackwall can be placed
in each building.
1
Locate and mark the center of the Trackwall.
2
Position the Trackwall with the center mark
by aligning with the center of the Wall Stud.
3
Use a level to position the Trackwall at the
desired height.
Front
Trackwall must be attached
to three (3) wall studs.
Wall Studs
42
Trackwall
Trackwall Assembly
4
03Q
Mark and drill six (6) 1/8” (3 mm) pilot holes
through the Trackwall. Then mark and
drill six (6) 1/8” (3 mm) holes into the Wall
Studs.
Trackwall sections should be placed with
Craftsman® logo in the lower left-hand corner
with the interlocking tongue facing up.
5
Align pilot holes of Trackwall with holes of
Wall Studs. Mount Trackwall to Wall Studs
using six (6) Screws. Screws must be flush
to surface. See figure below.
Driving screws further into the Trackwall
may reduce the capacity of the track.
Hang accesories following manufacturer’s instructions.
• Load Restrictions: 75 lbs (34 kg) per piece, 150 lbs
(68 kg) per shed side.
• Do not hang accessories to outside of outer screws.
43
ASSEMBLY NOTES
44
46A
ASSEMBLY NOTES
45
46A
ASSEMBLY NOTES
46
46A
ASSEMBLY NOTES
47
46A
37P
Product questions or problems?
1-800-851-1085
Customer Service
Get answers to questions, troubleshoot
problems, or order parts.
® Registered Trademark / TM Trademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries
">