ZANUSSI WD1210 User Manual

LAVADORASECADORA
WASHER-DRYER
WD 1010
WD 1210
DELAY
ON/OFF
COTTONS
SYNTHETICS
DELICATES
WOOL
HAND
WASH
90°C
60°C
50°C
40°C
30°C
132990990
P E R AT U R E
PREWASH
1200
900
700
500
EXTRA
RINSE
QUICK
WASH
RINSE
HOLD
SP
IN S P E E D
OP
TI O N S
WD 1010
COTTONS
EXTRA DRY
STORE DRY
IRON DRY
COTTONS
SYNTHETICS
STORE DRY
AU
TO
DRY
SKIP
SYNTHETICS
RY
I N G TI M E
D
EM
T
FA B R I C S
S TA RT
/ PA U S E
R ES E T
MANUAL DE USO
USER MANUAL
E
GB
Dear customer,
ENGLISH
Please read these operating instructions carefully
and pay particular attention to the safety notes
indicated in the first pages. We recommend that you
keep this instruction booklet for future reference and
pass it on to any future owners.
Transport damages
When unpacking the appliance, check that it is not
damaged. If in doubt, do not use it and contact the
Service Centre.
The symbols you will see on some paragraphs of this booklet have the following meaning:
The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly
important for your safety or correct functioning of the appliance.
The information marked with this symbol provides additional instructions and practical tips on the use of
the appliance.
Tips and information about economical and ecological use of the machine are marked with this symbol.
Our contribution to the protection of the
environment: we use recycled paper.
29
Contents
Warnings
Maintenance
31-32
52
Door seal
52
Bodywork
52
Tips for environmental protection 32
Detergent dispenser drawer
52
Drain pump
52
Technical specifications
33
Water inlet filter
53
Emergency emptying out
53
Installation
34
The dangers of freezing
53
Disposal
32
Unpacking
34
Positioning
34
Water inlet
34
Water drainage
35
Electrical connection
35
Your new washer-dryer
36
Description of the appliance
37
Door locked pilot light
37
Detergent dispenser drawer
37
Use
Control panel
Controls
38
38
38-41
Washing hints
42
Sorting the laundry
42
Temperatures
42
Before loading the laundry
42
Maximum loads
42
Laundry weights
42
Removing stains
42
Detergents and additives
43
Drying hints
44
International wash code symbols
45
Operating sequence
Something not working?
46-49
Washing programmes
50
Timed drying
51
30
54-55
Warnings
• Use only the recommended quantities of fabric
softener. An excessive amount could damage the
laundry.
Installation
• All internal packing must be removed before using
the appliance. Serious damage may be caused to
the machine or adjacent furniture if the protective
transit devices are not removed or are not
completely removed. Refer to the relevant
paragraph in the instruction book.
• Leave the porthole door slightly ajar when the
appliance is not in use. This preserves the door
seal and prevents the formation of musty smells.
• Always check that water has emptied out before
opening the door. If not, drain the water following
the instructions in the instruction book.
• Any electrical work required to install this appliance
must be carried out by a qualified electrician.
• Always unplug the appliance and shut the water
tap after use.
• Any plumbing work required to install this
appliance must be carried out by a qualified
plumber.
General safety
• After having installed the machine, check that it is
not standing on its electrical supply cable.
• If the appliance is placed on a carpeted floor,
ensure that air can circulate freely between the
feet and the floor.
• Repairs to the machine must be carried out only by
qualified personnel. Repairs carried out by
inexperienced persons could cause serious
danger. Contact your local Service Centre.
Use
• Never pull the power supply cable to remove the
plug from the socket; always take hold of the plug
itself.
• Never touch the machine while standing on a wet
floor or being barefoot.
• During high temperature wash programmes and
during the drying cycle the door glass may get hot.
Do not touch it!
• This appliance is designed for domestic use. It
must not be used for purposes other than those for
which it was designed.
• Only wash and dry fabrics which are designed to
be machine washed and dried. Follow the
instructions on each garment label.
• Do not overload the appliance. Follow the
instructions in the instruction book.
• Make sure that all pockets are empty. Objects such
as coins, safety pins, pins and screws can cause
extensive damage.
• Do not machine wash garments saturated with
petroleum, methylated spirits, trichlorethylene, etc.
If such fluids have been used to remove stains
prior to washing, wait until they have completely
evaporated from the fabric before placing
garments in the appliance.
• Place small items such as socks, belts, etc. in a
cloth bag or pillowcase to prevent them getting
trapped between the drum and the tub.
• If you use a liquid detergent with a dispenser which
has to be placed directly in the drum, remember to
remove this dispenser before drying.
31
ENGLISH
The following warnings are provided in the interests of overall safety. You must read them carefully before
installing or using the appliance.
• Make sure that children or pets do not climb into
the drum.
Child safety
• Children are often not aware of how dangerous
electrical appliances can be. When the machine is
working, children should be carefully supervised
and not be allowed to play with the appliance.
• When the appliance is to be scrapped, cut off the
electrical supply cable and destroy the plug with
the remaining cable. Disable the door catch in
order to prevent children from becoming trapped
inside while playing.
• The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children - danger
of suffocation! Keep them out of children’s reach.
• Keep all detergents in a safe place out of children’s
reach.
Disposal
Packaging materials
The materials marked with the symbol
recyclable.
Machine
are
Use authorised disposal sites for your old appliance.
Help to keep your country tidy!
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of
them properly in appropriate collection containers.
Tips for environmental protection
To save water, energy and to help protect the
environment, we recommend that you follow these
tips:
• With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature, so saving energy.
• Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
• Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
• The machine works more economically if it is fully
loaded, but do not overload it (see maximum moad
on page 30).
• The machine will consume less energy if the
laundry is adequately spun before being dried.
32
DIMENSIONS
Height
Width
Depth
85 cm
60 cm
57 cm
MAXIMUM LOAD
Cotton
Synthetics
Delicates
Woollens
WASHING
5 kg
2.5 kg
2.5 kg
2 kg
DRYING
2.5 kg
2 kg
-
SPIN SPEED
1000 rpm max. (WD 1010)
1200 rpm max. (WD 1210)
POWER SUPPLY VOLTAGE/FREQUENCY
TOTAL POWER ABSORBED
MINIMUM FUSE PROTECTION
220-230 V/50 Hz
2200 W
10 A
WATER PRESSURE
50 kPa
800 kPa
Minimum
Maximum
This appliance complies with the following EEC Directives:
73/23/EEC of 19/02/73 relating to low voltage
89/336/EEC of 03/05/89 relating to electromagnetic compatibility.
33
ENGLISH
Technical specifications
Installation
7. Plug all the holes with the plugs which you will
find in the envelope containing the instruction
booklet.
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
1. Using a spanner, unscrew and remove the two
rear bottom screws. Slide out the two plastic pins.
P1128
P0002
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that the
machine does not touch the wall or other kitchen
units.
Carefully level by screwing the adjustable feet in or
out. Never place cardboard, wood or similar
materials under the machine to compensate for any
unevenness in the floor.
P0001
P1129
2. Lay the machine on its back, taking care not to
squash the hoses. This can be avoided by
placing one of the corner packing pieces between
the machine and the floor.
3. Remove the polystyrene block from the bottom of
the machine and release the two plastic bags.
1
2
3
P1051
P1124
Water inlet
4. Very carefully slide out the left polythene bag,
removing it towards the right and then
downwards.
Connect the water inlet hose to a tap with a 3/4" thread.
The other end of the inlet hose which connects to the
machine can be turned in any direction. Simply
loosen the fitting, rotate the hose and retighten the
fitting, making sure there are no water leaks.
5. Very carefully slide out the right polythene bag,
removing it towards the left and then upwards.
P1126
P1127
P1088
6. Set the machine upright and remove the
remaining rear screw. Slide out the relevant pin.
P0021
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you will
have to purchase a new, longer hose specially
designed for this type of use.
34
Important!
Electrical connection
Before connecting up the machine to new pipework
or to pipework that has not been used for some time,
run off a reasonable amount of water to flush out any
debris that may have collected in the pipes.
Check that your domestic electrical installation can
take the maximum load required (2.2 kW), also
taking into account any other appliances in use.
Water drainage
Connect the machine to an earthed socket.
The end of the drain hose can be positioned in three
ways:
The manufacturer declines any responsibility
for damage or injury through failure to comply
with the above safety precaution.
Should the appliance power supply cable
need to be replaced, this should be carried
out by our Service Centre.
Hooked over the edge of a sink using the plastic
hose guide supplied with the machine. In this
case, make sure the end cannot come unhooked
when the machine is emptying.
This could be done by tying it to the tap with a piece
of string or attaching it to the wall.
Please ensure that when the appliance is
installed the power supply cable is easily
accessible.
P0022
In a sink drain pipe branch. This branch must be
above the trap so that the bend is at least 60 cm
above the ground.
Directly into a drain pipe at a height of not less
than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain pipe
must be larger than the outside diameter of the drain
hose.
The drain hose must not be kinked.
P1118
For a correct functioning of the machine the
drain hose must remain hooked on the proper
support piece situated on the top part of the back
side of the appliance
35
ENGLISH
This machine is designed to operate on a 220-230 V,
single-phase, 50 Hz supply.
Your new washer-dryer
This new washer-dryer meets all modern needs for effective treatment of laundry with low water, energy and
detergent consumption.
• The possibility of selecting the temperature, spin speed and all the options offered by this machine gives
you truly “customised” washing.
• The DELAY START option allows you to delay starting of the wash programme to any time of day, so
allowing you for instance to make use of overnight economy electricity tariffs.
• The programme progress display shows the programme steps selected and the programme phase which
is running.
• The special wool programme with its new delicate wash system treats your woollens with extreme care.
• The balance control device ensures the machine is stable during the spin.
• The Eco valve allows total use of detergent and reduces water consumption so saving energy.
• The drying programmes will give your wash that soft, relaxed feel whatever the weather.
Description of the appliance
1 Detergent dispenser drawer
1
2 Control panel
2
3 Door locked pilot light
4 Door handle
DELAY
COTTONS
SYNTHETICS
DELICATES
WOOL
HAND
WASH
90°C
60°C
50°C
40°C
30°C
EM
T
FA B R I C S
P E R AT U R E
PREWASH
1200
900
700
500
EXTRA
RINSE
QUICK
WASH
RINSE
HOLD
SP
IN S P E E D
OP
TI O N S
WD 1010
COTTONS
EXTRA DRY
STORE DRY
IRON DRY
COTTONS
SYNTHETICS
STORE DRY
AU
TO
DRY
SKIP
SYNTHETICS
RY
I N G TI M E
D
5 Drain pump
ON/OFF
S TA RT
/ PA U S E
R ES E T
6 Adjustable feet
4
Door locked pilot light
It stays on during the whole programme indicating
that the door is locked.
When the light goes out, the door can be opened
(see page 48).
5
6
Detergent dispenser drawer
Prewash
Main wash
Fabric softener, starch
C0063
36
3
Use
Control panel
RETARDO
2
3
4
T RI F U G A D
OP
5
SECO
ARMARIO
CI O N E S
EC
6
ADO AUTO
7
ALGODON
PROGR.
ESPEC.
SINTETICOS
SEC A DO
A TI E M P O
8
S TA R T/ PA U S A
9 10
A N U L.
111213
1 ON/OFF button
(MARCHA PARADA)
Maximum temperatures are 90°C for cotton, 60°C for
synthetic fabrics, 40°C for delicate fabrics, wool and
fabrics to be hand-washed (HAND WASH programme).
Press this button to switch the washing machine on.
The display (9) will show three blinking dashes or a
blinking zero. You will find more detailed
explanations on pages 38-39 (see “DISPLAY”).
Press the ON/OFF button again to switch the
machine off.
By selecting position FRIO the machine will wash with
cold water. To be used for extremely delicate items,
such as curtains.
Important!
By depressing TEMPERATURE (TEIJDOS) and
SPIN SPEED (CENTRIFUGADO) buttons
simultaneously, the acoustic signal when selecting
the programmes, in case of incorrect option and at
the end of the cycle is suppressed.
2 MAINS-ON light
This light is connected to the ON/OFF button. It lights
up when you press the button, and goes out when
you press it again.
5 SPIN SPEED button
(CENTRIFUGADO)
3 FABRIC button (TEIJDOS)
Press this button repeatedly to change the spin
speed, if you want your laundry to be spun at a
speed different from the one proposed by the
machine. The relevant light will light up.
Press this button repeatedly to select the programme
on the basis of the type of laundry to be washed. The
light relevant to the selected programme will light up.
The machine will propose a temperature and
automatically select the maximum spin value provided
for the programme you have chosen. You can change
these values by operating buttons 4 and 5.
Maximum speeds are:
• for cotton: 1,000 rpm (WD 1012) or 1,200
(WD1210);
• for synthetic fabrics, wool, and fabrics to be handwashed: 800 rpm;
• for delicate fabrics: 600 rpm.
Hand wash
(Lavado a mano)
When you select this programme, you obtain a
particularly delicate washing, suitable for articles of
clothing whose label indicates that they must be
hand-washed
.
RINSE HOLD (AGUA EN LA CUBA) position :
when you choose this option, the machine will not
drain the water of the last rinse, so as not to wrinkle
the laundry.
At the end of the cycle, the START/PAUSE button
light will flash to indicate that the water must be
drained and a zero fixe will appear in the display.
The DOOR LOCKED light remains lit.
To complete the cycle, choose one of the following
options:
4 TEMPERATURE button
Press this button repeatedly to increase or decrease
the temperature, if you want your laundry to be washed
at a temperature different from the one proposed by the
machine. The relevant light will light up.
• Draining and spin:
- Press the START/PAUSE button. The machine
37
ENGLISH
EN
LAVADO
RAPIDO
S
1
P E R AT U R A
C
EM
T
T E JI D O S
AGUA EN
LA CUBA
SECO ARMARIO
HUMEDO
PLANCHA
.
LAVADO
A MANO
ACLARADO
ADICIONAL
M
RCHA/PARADA
MA
EXTRA SECO
PRELAVADO
1000
900
700
400
90°C
60°C
40°C
30°C
FRIO
O
ALGODON
SINTETICOS
DELICADOS
LANA
WD 1010
will drain the water, then spin the laundry at the
maximum speed provided for the selected
programme.
- Select spin speed by means of button 5, and
press the START/PAUSE button.
• Drain only
- Press the RESET (ANUL.) button once, so as to
cause the DRAIN light
to light up, then press
the START/PAUSE button.
7 Automatic Drying button
(SECADO AUTOMATICO)
By means of this button you can choose the required
degree of drying for cottons and synthetics:
EXTRA SECO = Extra dry (cottons)
SECO ARMARIO = Store dry (cottons and synthetics)
HUMEDO PLANCHA = Iron dry (cottons)
The corresponding pilot light illuminates.
Important! If you accidentally press the RESET
(ANUL.) button more than once, the display will show
three blinking dashes. To drain the water, select
any washing programme by means of the FABRIC
(TEJIDOS) button, then press RESET (ANUL.) three
times in order to select the DRAIN
position (only
the DRAIN light
will remain lit)
then press again the START/PAUSE button.
The drying time is automatically adjusted by the
machine: the laundry will be dried to the selected
degree of dryness.
8
The RINSE HOLD option cannot be selected for the
automatic WASHING & DRYING programme.
Timed Drying button
(SECADO A TIEMPO)
If you wish to carry out a timed programme instead
of an electronic programme push this button: the
light corresponding to the selected fabric illuminates.
To select COTTON (ALGODON) push the button for
two seconds.
To select the drying time push the button until the
drying time you want appears in the display
according to the fabrics (cotton or synthetics) you
have to dry. Every time you push the button the time
increases by 5 mins.
For COTTON you can select a drying time from 10
minutes to 130 minutes.
For SYNTHETICS you can select a time from 10
minutes to 100 minutes.
6 OPTIONS button (OPCIONES)
Press this button to select the following options:
• PREWASH (PRELAVADO): select this option if
you wish your laundry to be prewashed at 30° C
before the main wash (not available for wool and
hand-wash cycle).
The prewash ends with a short spin in
programmes for cotton and synthetic fabrics,
whereas in the programme for delicate fabrics the
water is only drained.
• SUPER RINSE (ACLARADO ADICIONAL): this
option can be selected with all programmes
except the wool programme and hand wash.
The machine performs 4 rinses instead of 3. This
option is recommended for people who are allergic
to detergents, and in areas where the water is very
soft.
9 Display
The following pieces of information are shown on the
display:
• Three blinking dashes, when a programme is
cancelled by means of the RESET (ANUL.) button.
• QUICK WASH (LAVADO RAPIDO): this option is
for laundry that is only slightly soiled (not for wool
and HAND WASH programme).
The three blinking dashes will also appear when you
press the ON/OFF button to switch the machine on,
if the previously selected cycle has been erased.
The washing time will be reduced according to the
type of fabric and the selected temperature.
---
38
• Delay start (Arranque retardado), a time value
indicated in hours and selected by means of the
relevant button.
ENGLISH
• Duration of washing programme in hours
and minutes, after you have selected a
programme.
2.05
While the programme is running (after you have
pressed the START/PAUSE button), the displayed
time value decreases by one unit every minute.
• Drying time: the selected drying time is displayed
in minutes or hours and minutes.
The delay time is displayed for 3 seconds, then the
duration of the selected programme reappears.
After you have pressed the START/PAUSE button,
the countdown begins, and the delay time value
decreases by one unit every hour.
You can delay the start of the selected programme
by up to 24 hours in one hour intervals.
• An incorrect option selection has been made:
this is indicated by the message Err when a
function incompatible with the current programme
is selected.
1.25
After starting the programme, the remaining time is
updated every minute.
• The machine has stopped with water in the tub,
at the end of a programme with the RINSE HOLD
(AGUA EN LA CUBA) option: this is indicated by a
static zero.
• The machine has completed the programme:
this is indicated by a blinking zero. At the same
time, the door locked light goes out. The zero will
reappear when you switch the machine on, unless
the previous programme has been erased by
means of the RESET (ANUL.) button.
The incorrect selection is also indicated by an
audible warning signal.
• An alarm code indicates a fault in the machine
operation (see the relevant chapter on page 54).
E20
0
Important!
The first time you use the machine, when you
switch it on, it may display a blinking zero and give an
audible warning signal. This is due to the fact that the
machine has performed a washing cycle during the
manufacturer’s inspection tests, and this cycle has not
been erased after its completion.
39
Example:
10 START/PAUSE button
In this case, only the
spin (at the speed
provided for the
selected type of fabric)
will be performed.
This button has three functions:
• Start: after you have selected the desired
programme and options, press this button to start
the machine. The light above the button will stop
flashing and remain lit.
If you have selected a delay time by means of
button 12, the countdown will begin and will be
shown on the display.
• Pause: when you press this button again, the
programme in progress is interrupted. The light
above the button will start flashing. To restart the
programme, press the button again.
This button allows you also to select special
programmes, such as RINSES, SPIN and DRAIN.
• If the machine is already switched on because it
has just performed a washing programme, proceed
as follows:
When you PAUSE the cycle, the DOOR LOCKED
light goes out, and it becomes possible to open the
door, provided
- depress RESET (ANUL.) once or repeatidly to
cancel the previously performed programme (three
blinking dashes will appear on the display);
• the machine is not in the heating or drying phase;
• the level of the water is not high;
• the drum is not turning.
- select the type of fabric by means of button
TEJIDOS;
Important! You must set the machine to PAUSE
before you make any change in the programme in
progress.
- select the special programme:
• RINSES AND SPIN
• Draining of water and spinning after the
execution of programmes with the RINSE HOLD
(AGUA EN LA CUBA) option.
Depress RESET (ANUL.) once, the pilot light
(WASH) goes out.
• SPIN
Depress RESET (ANUL.) twice, the pilot lights
WASH
and RINSES
go out.
11 RESET (ANUL.) button
• DRAIN
At the end of a programme, you must press this
button once or repeatedly, in order to clear the
contents of the memory (the display will show three
blinking dashes); otherwise, the next time you switch
the machine on, the blinking zero will reappear and
the audible warning signals relevant to the end of the
previous cycle will be given.
Depress RESET (ANUL.) three times, the pilot
lights WASH
, RINSES
and SPIN
go
out and the only pilot light
will remain lit.
Example:
In this case the
machine will perform
the rinses and spin.
You can also press the RESET (ANUL.) button to
exclude one or several phases of the programme
which is running, as indicated below.
- set the machine to PAUSE by pressing the
START/PAUSE button (the relevant light will flash);
- press the RESET (ANUL.) button once or several
times, until the required phase(s) is(are) cancelled
(the light next to the name of the phase(s) will go out).
• If the machine is switched off:
- depress ON/OFF button to switch it on;
- select the type of fabric by means of button
TEJIDOS:
- select the special programme as previously
described.
40
12 DELAY (RETARDO) button
ENGLISH
This button makes it possible to delay the starting of
the programme by up to 24 hours. The delay you
have selected is shown on the display for about 3
seconds; afterwards, the duration of the programme
reappears.
You must select this option after you have set the
programme and before you press the
START/PAUSE button.
The time value shown on the display will decrease
by one unit every hour.
You can change the delay time at any moment,
before you press the START/PAUSE button.
If you have already pressed the START/PAUSE
button, and you wish to change or cancel the delay
time, proceed as follows:
• set the machine to PAUSE by pressing the
START/PAUSE button;
• press the DELAY button until the display shows the
desired delay time or
• press the DELAY button once, to erase the delay
time. The display will indicate “0h”.
• press the START/PAUSE button again.
Important!
The door will be locked throughout the delay time
(DOOR LOCKED light lit).
If you need to open the door, you must first set the
washing machine to PAUSE by pressing the
START/PAUSE button. After you have closed the
door, press the START/PAUSE button again.
13 Programme phase indicator
lights
When you select a programme, the lights relevant to
the phases that form the programme light up.
After you have started the programme, only the light
relevant to the phase that is currently being carried
out will remain lit.
41
Laundry weights
Washing hints
The following weights are indicative:
Sorting the laundry
bathrobe
Follow the wash code symbols on each garment
label and the manufacturer’s washing instructions.
Sort the laundry as follows:
whites, coloureds, synthetics, delicates, woollens.
napkin
100 g
quilt cover
700 g
1200 g
sheet
500 g
pillow case
200 g
Temperatures
tablecloth
250 g
90°
towelling towel
200 g
tea cloth
100 g
60°
for normally soiled white cottons and linen
(e.g. tea cloths, towels, tablecloths,
sheets...)
for normally soiled, colour fast garments
(e.g. shirts, night dresses, pyjamas....) in
linen, cotton or synthetic fibres and for
lightly soiled white cotton (e.g. underwear).
night dress
200 g
ladies’ briefs
100 g
man’s work shirt
600 g
man’s shirt
200 g
man’s pyjamas
500 g
Frio (cold) for delicate items (e.g. net curtains),
30°-40° mixed laundry including synthetic fibres
and woollens.
blouse
100 g
men’s underpants
100 g
Before loading the laundry
Removing stains
Never wash whites and coloureds together. Whites
may lose their “whiteness” in the wash.
Stubborn stains may not be removed by just water
and detergent. It is therefore advisable to treat them
prior to washing.
New coloured items may run in the first wash; they
should therefore be washed separately the first time.
Blood: treat fresh stains with cold water. For dried
stains, soak overnight in water with a special
detergent then rub in the soap and water.
Make sure that no metal objects are left in the
laundry (e.g. hair clips, safety pins, pins).
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab the
stain; treat several times.
Button up pillowcases, close zip fasteners, hooks
and poppers. Tie any belts or long tapes.
Remove persistent stains before washing. Rub
particularly soiled areas with a special detergent or
detergent paste.
Dried grease stains: moisten with turpentine, lay
the garment on a soft surface and dab the stain with
the fingertips and a cotton cloth.
Treat curtains with special care. Remove hooks or tie
them up in a bag or net.
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with rust
stains which are not recent since the cellulose
structure will already have been damaged and the
fabric tends to hole.
Maximum loads
Recommended loads are indicated in the
programme charts.
Mould stains: treat with bleach, rinse well (whites
and fast coloureds only).
General rules:
Synthetics: drum no more than half full;
Grass: soap lightly and treat with bleach (whites and
fast coloureds only).
Delicate fabrics and woollens: drum no more than
one third full.
Ball point pen and glue: moisten with acetone (*),
lay the garment on a soft cloth and dab the stain.
Washing a maximum load makes the most efficient
use of water and energy.
Lipstick: moisten with acetone as above, then treat
stains with methylated spirits. Remove any residual
marks from white fabrics with bleach.
Cotton, linen: drum full but not too tightly packed;
For heavily soiled laundry, reduce the load size.
Red wine: soak in water and detergent, rinse and
treat with acetic or citric acid, then rinse. Treat any
42
residual marks with bleach.
Quantity of detergent to be used
Ink: depending on the type of ink, moisten the fabric
first with acetone (*), then with acetic acid; treat any
residual marks on white fabrics with bleach and then
rinse thoroughly.
Water hardness is classified in so-called “degrees”
of hardness. Information on hardness of the water
in your area can be obtained from the relevant water
supply company, or from your local authority.
Tar stains: first treat with stain remover, methylated
spirits or benzine, then rub with detergent paste.
(*) do not use acetone on artificial silk.
Follow the product manufacturers’ instructions on
quantities to use.
Detergents and additives
Use less detergent if:
Good washing results also depend on the choice of
detergent and use of the correct quantities to avoid
waste and protect the environment. Although
biodegradable, detergents contain substances
which, in large quantities, can upset the delicate
balance of nature.
– you are washing a small load,
– the laundry is lightly soiled,
– large amounts of foam form during washing.
Degrees of water hardness
The choice of detergent will depend on the type of
fabric (delicates, woollens, cottons, etc.), the colour,
washing temperature and degree of soiling.
Degrees
All commonly available washing machine detergents
may be used in this appliance:
Level
Characteristic
1
soft
– liquid detergents, preferably for low temperature
wash programmes (60°C max) for all types of
fabric, or special for woollens only.
2
medium
The detergent and any additives must be placed in
the appropriate compartments of the dispenser
drawer before starting the wash programme.
3
hard
4
very hard
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (60°C max)
and woollens,
If using concentrated powder or liquid detergents, a
programme without prewash must be selected.
The washing machine incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Pour liquid detergent into the dispenser drawer
compartment marked
just before starting the
programme.
Any fabric softener or starching additives must be
poured into the compartment marked
before
starting the wash programme.
Follow the product manufacturer’s recommendations
on quantities to use and do not exceed the «MAX»
mark in the detergent dispenser drawer.
43
German
°dH
French
°T.H.
0- 7
0-15
8-14
16-25
15-21
26-37
more than more than
21
37
ENGLISH
The type and quantity of detergent will depend on
the type of fabric, load size, degree of soiling and
hardness of the water used.
Drying symbols on garment labels
Drying hints
Always look at the garment label to check whether
garments can be machine dried.
As a dryer, the machine works on the condensation
principle.
The following symbols refer to drying:
Therefore, the water tap must be open and the
drain hose must drain water into a sink or into
the drain pipe, even during the drying cycle.
Machine drying is usually possible
Normal drying (normal temperature)
Load
Gentle drying (reduced temperature)
Do not machine dry
Sort of laundry
max. load
(dry weight)
Duration of the drying cycle
Linen and cottons
2.5 kg
The drying time can vary according to
Synthetics
2
• the final spin speed;
kg
• the required degree of drying (extra dry, store dry
or iron dry);
Warning:
• the type of laundry;
Loads of washed laundry exceeding these values
must be divided before being dried, otherwise
poor results will be obtained.
• the size of load.
The usual drying times for the timed programmes are
indicated in the programme chart. As you become
more familiar with the appliance, you will discover
the drying times that best suit your needs according
to the various type of fabric. It is a good idea to make
a note of these times.
Garments not suitable for drying
• Particularly delicate items such as synthetic
curtains, woollen and silk, garments with metal
inserts, nylon stockings, bulky garments such as
anoraks, bedcovers, quilts, sleeping bags and
duvets must not be machine dried.
Fibre residue
After drying fluffy fabrics, such as new towels, it is
advisable to perform the rinse programme
to be
sure that any residue that may remain in
the tub is completely removed and does not stick to
garments dried afterwards.
• Garments padded with foam-rubber or materials
similar to foam-rubber must not be machine dried;
they represent a fire hazard.
• Also, fabrics containing residues of setting lotions
or hair sprays, nail solvents or similar solutions
must not be machine dried in order to avoid the
formation of harmful vapours.
After each drying cycle the filter should be
checked and cleaned.
Additional drying
Should the laundry still be too wet at the end of the
programme, set another short drying cycle.
Warning! To prevent the formation of creases or
shrinking of fabrics, avoid excessive drying.
44
International wash code symbols
Energetic wash
95
60
40
30
Max. wash
temperature
95°C
Max. wash
temperature
60°C
Max. wash
temperature
40°C
Max. wash
temperature
30°C
Delicate wash
60
Bleaching
Bleach in cold water
40
ENGLISH
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
Hand wash
30
40
Do not
wash
at all
Do not bleach
Ironing
Hot iron
max 200°C
Warm iron
max 150°C
Lukewarm iron
max 110°C
Do not iron
Dry cleaning
Dry cleaning
in all solvents
Dry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 & R 113
Dry cleaning
in petrol,
pure alcohol
and R 113
Do not
dry clean
high
temperature
low
temperature
Drying
Flat
On the line
On clothes
hanger
45
Tumble dry
Do not
tumble dry
To switch the machine on, press the ON/OFF button
: the mains-on light comes on.
Operating sequence
The display will show three blinking dashes or a
blinking zero.
Wash only
Before the first wash we recommend that you pour 2
litres of water into the main wash compartment
of the detergent drawer in order to activate the
ECO valve. Then run a cotton cycle at 60°C, with the
machine empty, in order to remove any
manufacturing residue from the drum and tub.
Pour half a measure of detergent into the main wash
compartment and start up the machine.
RCHA/PARADA
MA
0
---
1. Place the laundry in the drum
5. Select the desired programme/
fabric
Open the door.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible.
Press the FABRIC (TEIJDOS) button repeatedly, in
order to select the desired programme/fabric. The
relevant light will light up.
Close the door.
The lights relevant to the phases that form the
programme will light up.
The display will show the duration of the selected
programme, calculated on the basis of the maximum
load for each type of fabric. The START/PAUSE
button light will start flashing.
If the load of laundry to be washed is small, at the
beginning of the cycle the display will still indicate the
duration relevant to the maximum load. The duration
value will be gradually adjusted during the execution
of the cycle.
P0004
2. Measure out the detergent
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent recommended by the
manufacturer in a graduated cup and pour it into the
main wash compartment
.
ALGODON
SINTETICOS
DELICADOS
LANA
If you wish to carry out the prewash, pour detergent
into the appropriate compartment marked
.
LAVADO
A MANO
T E JI D O S
3. Measure out the additives
If required, pour fabric softener into the compartment
marked
without exceeding the «MAX» mark.
C0064
C0065
4. Switch the machine on
46
If your laundry is only slightly soiled, select the
QUICK WASH (LAVADO RAPIDO) option.
The relevant light illuminates.
6. Select the temperature
Press the TEMPERATURE button if you wish to
select a temperature value different from the one
proposed by the machine.
The relevant light will light up.
Before you start the programme, if you wish the
starting to be delayed, press the DELAY
(RETARDO) button repeatedly, or keep it pressed, to
select the desired delay. The selected delay time
value (up to 24 hours) will appear on the display for 3
seconds, then the duration of the programme will
appear again.
90°C
60°C
40°C
30°C
FRIO
T
EM
P E R AT U R A
RETARDO
7. Select the spin speed or the
RINSE HOLD (AGUA EN LA
CUBA) option
Press the SPIN SPEED (CENTRIFUGADO) button
repeatedly, in order to select the desired spin speed
or the RINSE HOLD (AGUA EN LA CUBA) option.
The relevant light will light up.
If you select the RINSE HOLD option, the machine
will stop at the end of the programme with the water
still in the tub.
10. Start the programme
Press the START/PAUSE button. The relevant light
will stop flashing, the DOOR LOCKED light will light
up, and only the light relevant to the phase that is in
progress will remain lit.
If you have chosen a delayed start, the machine will
begin the countdown.
The display will show the duration of the programme
or the selected delay.
1000
900
700
500
AGUA EN
LA CUBA
T RI F U G A D
O
C
EN
8. Select the desired options
S TA R T / P A U S A
If your laundry is very dirty, it may be advisable to
select the PREWASH (PRELAVADO) option.
If you wish the laundry to undergo an extra rinse,
select the SUPER RINSE (ACLARADO ADICIONAL)
option.
Press the OPTIONS (OPCIONES) button so as to
cause one or both of the lights to light up.
11. How to change a programme
during its cycle
Before you make any change, you must pause the
machine by pressing the START/PAUSE button.
It is possible to change any phase before the
programme carries it out.
Changing the type of fabric or temperature is
possible, obviously, only during the washing phase.
When you make a change in these two parameters,
the machine will resume the cycle from the
beginning.
PRELAVADO
ACLARADO
ADICIONAL
LAVADO
RAPIDO
OP
CI O N E S
47
ENGLISH
9. Select the DELAY TIME
If it is necessary to drain the water in order to change
the programme in progress, proceed as follows:
14. End of programme
• PAUSE the machine by pressing the
START/PAUSE button;
• press the RESET (ANUL.) button repeatedly, until
only the DRAIN light
remains lit;
At the end of the programme, the machine stops
automatically, gives an audible signal, and displays a
blinking zero.
If you had selected the RINSE HOLD (AGUA EN LA
CUBA) option, the START/PAUSE button light
flashes to indicate that the water must be drained.
The display shows a steadily lit zero and the the
DOOR LOCKED light remains lit.
When the programme has been completed, a
blinking zero appears on the display and the audible
signal is given.
• press the START/PAUSE button again.
When the water has been drained, the display shows
a blinking zero. You may now select a new
programme and press the START/PAUSE button to
start it.
The DOOR LOCKED light goes out at once.
12. How to cancel a programme
during its cycle
Press the SKIP/RESET button repeatedly to erase
the programme that has just been carried out. If
you omit to do this, the next time you switch the
machine on, the blinking zero will appear on the
display and you will hear the audible signal.
To cancel a programme that is being carried out, first
pause the machine by pressing the START/PAUSE
button, then press the RESET (ANUL.) button
repeatedly, until the display shows three blinking
dashes.
Note: when you switch the machine on, if you must
erase the previously performed programme, it is also
sufficient to press the FABRIC (TEJIDOS) button
and select a new programme.
13. How to open the door during
the cycle of a programme
Press the ON/OFF button to switch the machine off.
The relevant light will go out.
You can open the door, after having set the machine
to PAUSE, provided the following conditions exist:
Remove the laundry from the machine.
Check whether the drum is completely empty, by
rotating it with your hand. The purpose of this is to
prevent any items of laundry from remaining
accidentally in the drum, where they might get
damaged in a subsequent wash (e.g. by shrinking) or
bleed colour into another load of laundry.
• the machine is not in the heating phase beyond
55°C;
• the level of the water is not high;
• the drum is not turning.
If these requirements are met, when you pause the
machine, the DOOR LOCKED light goes out and the
door can be opened.
We advise you to close the water supply tap and
disconnect the plug from the socket.
Leave the door ajar in order to air the machine.
Should it not be possible to open the door, and
should it be absolutely necessary to do so, switch
the machine off by pressing the ON/OFF button.
After approximately 3 minutes, you can open the
door.
Pay attention to the level and temperature of the
water in the machine!
When you close the door and press the ON/OFF
button again, the machine will resume the
programme from the point where it had been
interrupted.
48
Automatic washing and drying
(NON-STOP programme)
Warning! Do not exceed the maximum laundry
loads:
Warning! For NON-STOP programmes, it is also
essential not to exceed the maximum load sizes of
2.5 kg for cotton and 2 kg for synthetics.
- 2.5 kg for linen and cottons
- 2
kg for synthetics.
Do not use a dosing device/ball when carrying
out a washing & drying programme.
The water tap must be open and the drain hose must
be positioned in the sink or connected to the drain
pipe.
1. Load the laundry.
1. Press the RESET (ANUL.) button repeatedly to
erase the programme that has just been carried
out.
2. Add detergent and additive.
3. Switch the machine on by depressing the
ON/OFF button
.
2. Switch the machine off by depressing ON/OFF
button.
4. Select the wash programme.
5. Select eventually the required options by means
of the relevant buttons. If possible, do not select a
spin speed lower than that proposed by the
appliance to avoid a too long drying time so
saving energy.
In any case the reduction of the spin speed is
only possible after selecting drying. The lowest
values you can select are the following:
- 900 r.p.m. for cottons & synthetics with
electronic drying
- 900 r.p.m. for cottons and 700 r.p.m. for
synthetics with timed drying
3. Load the laundry
4. Depress the ON/OFF button
machine on.
to switch the
5. If you wish to carry out the electronic drying,
depress button SECADO AUTOM. until the pilot
light corresponding to the degree of dryness
required illuminates.
EXTRA SECO
SECO ARMARIO
HUMEDO
PLANCHA
6. Select the drying time or degree of drying.
SECO
ARMARIO
.
ADO AUTO
M
S
EC
7. Start the programme by depressing the
START/PAUSE button.
8. At the end of the programme, press the RESET
(ANUL.) button to clear the memory and press
the ON/OFF button again to switch the machine
off.
6. If you want a timed drying, depress button
SECADO A TIEMPO until light ALGODON
(COTTONS) or SINTETICOS (SYNTHETICS)
lights up, then depress the same button until the
time you want appears on the display.
9. Remove the laundry.
ALGODON
SINTETICOS
SEC A DO
A TI E M P O
7. Press the START/PAUSE button
programme.
to start the
8. At the end of the cycle, press RESET (ANUL.)
button to clear the memory and press the
ON/OFF button again to switch the appliance off.
9. Remove the laundry.
49
ENGLISH
Drying only
Programme chart
Washing programmes
Type of
laundry and
symbols on
labels
60
95
White cotton:
e.g. sheets,
tablecloths,
household
linen
60
40
30
Load
40
30
30
Delicate fabrics: e.g.
acrylic fabrics,
viscose, polyester,
synthetic
blends
40
30
Consumption*
Energy
kWh
Water
litres
Time
h/min.
CENTRIFUGADO
AGUA EN LA CUBA
PRELAVADO
ACLARADO
ADICIONAL
LAVADO RAPIDO
1.8
52
2.28
Cottons
Algodón
60°-40°-30°C
FRIO (COLD)
Wash at
60°-40°-30°C
or cold
3 rinses
Long spin
CENTRIFUGADO
AGUA EN LA CUBA
PRELAVADO
ACLARADO
ADICIONAL
LAVADO RAPIDO
0.95
49
2.10
2.5 kg
Synthetics
Sintéticos
60°-40°-30°C
FRIO (COLD)
Wash at
60°-40°-30°C
or cold
3 rinses
Short spin
CENTRIFUGADO
AGUA EN LA CUBA
PRELAVADO
ACLARADO
ADICIONAL
LAVADO RAPIDO
0.9
47
1.27
2.5 kg
Delicates
Delicados
40°-30°C
FRIO (COLD)
Wash at
40°-30°C
or cold
3 rinses
Short spin
CENTRIFUGADO
AGUA EN LA CUBA
PRELAVADO
ACLARADO
ADICIONAL
LAVADO RAPIDO
0.4
45
1.04
2 kg
Wool
Lana
40°-30°C
FRIO (COLD)
Wash at
40°-30°C
or cold
3 rinses
Short spin
CENTRIFUGADO
AGUA EN LA CUBA
0.4
46
53
2 kg
Hand wash
Lavado
a mano
40°-30°C
FRIO (COLD)
Wash at
40°-30°C
or cold
3 rinses
Short spin
CENTRIFUGADO
AGUA EN LA CUBA
0.4
46
55
Cottons
Algodón
60°-90°C
5 kg
Synthetic
fabrics and
blends: e.g.
shirts,
blouses,
underwear
40
Description of
Available options
programme
Wash at
60°-90°C
3 rinses
Long spin
5 kg
** Coloured
cotton: e.g.
shirts,
blouses,
underwear,
towels, household linen
60
Programme/
temperature
Wool
**The “coloured cotton programme” at 60°C is the reference programme for the data entered in the energy
label, in compliance with EEC 92/75 standards. .
* This data is given purely as an indication: the consumption values may vary in relation to the quantity and
type of laundry, the temperature of the water supply and the ambient temperature.
50
Programme table
Degree of
drying
Extra dry
Ideal for
towelling
materials
Store dry (*)
Suitable for
items to put
away without
ironing
Iron dry
Suitable for
ironing
Type of fabric
Cotton and linen
(bathrobes, bath
towels, etc.)
Cotton and linen
(towels, T-shirts,
bathrobes)
Synthetics and
mixed fabrics
(jumpers, blouses,
underwear,
household linen)
Cotton and linen
(sheets, tablecloths,
shirts, etc.)
Max. load
2.5 kg
1.5 kg
2.5 kg
1.5 kg
Spin speed
Drying time
mins
1000
85
1200
80
1000
65
1200
60
1000
75
1200
70
1000
55
1200
50
2
kg
900
75
1
kg
900
40
1000
60
1200
55
1000
50
1200
45
2.5 kg
1.5 kg
(*) The STORE DRY drying programme for cotton is the reference programme for the Energy Label data, in
compliance with EC directive 92/75.
51
ENGLISH
Timed drying
Maintenance
1. Door seal
4 Drain pump
Check from time to time the door seal and eliminate
eventual possible objects that could be trapped in
the fold.
The pump should be inspected regularly and
particularly if
• the machine does not empty and/or spin
• the machine makes an unusual noise during
draining due to objects such as safety pins, coins
etc. blocking the pump.
Proceed as follows:
• Disconnect the appliance.
• If necessary wait until the water has cooled down.
• Open the pump door.
P1050
2. Bodywork
Clean the outside of the machine with warm water
and a neutral, non-abrasive household detergent.
Rinse with clean water and dry with a soft cloth.
Important: do not use methylated spirits, solvents or
similar products to clean the bodywork.
P1095
Place a container close to the pump to collect any
spillage.
• Release the emergency emptying hose, place it in
the container and remove its cap.
• When no more water comes out, unscrew the
pump and remove it. Always keep a rag nearby to
dry up spillage of water when removing the pump.
3. Detergent dispenser drawer
After a while, detergents and fabric softeners leave
deposits in the drawer.
Clean the drawer from time to time by rinsing it under
a running tap. To remove the drawer from the
machine, press the button in the rear left-hand
corner.
To facilitate cleaning, the top part of the additive
compartments can be removed.
P1096
• Remove any objects from the pump impeller by
rotating it.
C0066
C0067
Detergent can also accumulate inside the drawer
recess: clean it with an old toothbrush. Refit the
drawer after cleaning.
P1097
P0038
52
• Put the cap back on the emergency emptying hose
and place the latter back in its seat.
• replace the emergency emptying hose in its seat
after having plugged it;
7 Frost precautions
If the machine is installed in a place where the
temperature could drop below 0°C, proceed as
follows:
• Remove the plug from the socket.
P1098
• Close the water tap and unscrew the water inlet
hose from the tap.
• Screw the pump fully in.
• Close the pump door.
• Place the end of the emergency emptying hose
and that of the inlet hose in a bowl placed on the
floor and let water drain out.
5. Water inlet filter
• Screw the water inlet hose back on and reposition
the emergency emptying hose after having put the
cap on again.
If you notice that the machine is taking longer to fill,
check that the filter in the water inlet hose is not
blocked.
By doing this, any water remaining in the machine is
removed, avoiding the formation of ice and,
consequently, breakage of the affected parts.
Turn off the water tap.
Unscrew the hose from the tap.
When you use the machine again, make sure that
the ambient temperature is above 0°C.
Clean the filter with a stiff brush.
Screw the hose back onto the tap.
Important!
Every time you drain the water through the
emergency emptying hose you must pour 2 litres of
water into the main wash compartment of the
detergent drawer and then run the drain programme.
This will activate the ECO valve avoiding that part of
the detergent remains unused at next washing.
P1090
6 Emergency emptying out
If the water is not discharged, proceed as follows to
empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• open the the pump door;
• place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove
its cap. The water should drain by gravity into the
bowl. Whe the bowl is full, put the cap back on the
hose. Empty the bowl. Repeat the procedure until
water stops flowing out;
• clean the pump if necessary as previously
described;
53
ENGLISH
• screw the pump again and close the door.
Something not working?
Problems which you can resolve yourself.
During machine operation it is possible that un acoustic signal sounds and one of the following alarm codes
appears on the display:
- E10: problem with the water supply
- E20: problem with water draining
- E40: door open
Once the problem has been eliminated, press the START/PAUSE button
all checks, the problem persists, contact your local Service Centre.
Problem
to restart the programme. If after
Possible cause
• The machine does not start up:
• The door is not firmly closed. (E40)
• The machine is not plugged in or there is no power
at the socket.
• The main fuse has blown.
• The START/PAUSE button has not been
depressed.
• The DELAY START (ARRANQUE RETARDADO)
option has been selected.
• The machine does not fill:
•
•
•
•
• The machine fills then empties
immediately:
• The end of the drain hose is too low. Refer to
relevant paragraph in “water drainage” section.
• The machine does not empty
and/or does not spin:
• The drain hose is squashed or kinked. (E20)
• The option AGUA EN LA CUBA has been
selected.
• The drain pump is clogged. (E20)
• There is water on the floor:
• Too much detergent or unsuitable detergent
(creates too much foam) has been used.
• Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this
as the water runs down the hose; check to see if it
is damp.
• The drain hose is damaged.
The water tap is closed. (E10)
The inlet hose is squashed or kinked. (E10)
The filter in the inlet hose is blocked. (E10)
The door is not properly closed. (E40)
• The cap on the emergency emptying hose has not
been replaced after cleaning the filter.
• Unsatisfactory washing results:
• Too little detergent or unsuitable detergent has
been used.
• Stubborn stains have not been treated prior to
washing.
• The correct temperature was not selected.
• Excessive laundry load.
• The machine vibrates or is
noisy:
• The transit bolts and packing have not been
removed.
• The support feet have not been adjusted.
• The laundry is not evenly distributed in the drum.
• Maybe there is very little laundry in the drum.
• The door will not open:
•
•
•
•
The door can be opened when the relevant light
has gone off.
54
The programme is still running, the drum is turning.
The door lock has not yet released.
The water level is above the bottom edge of the door.
The machine is heating the water.
Possible cause
• Spinning starts late or the
laundry is not spun enough:
• The electronic unbalance detection device has cut
in because the laundry is not evenly distributed in
the drum. The laundry is redistributed by reverse
rotation of the drum. This may happen several
times before the unbalance disappears and normal
spinning can resume. If, after few minutes, the
laundry is still not evenly distributed in the drum,
the machine will spin at a lower speed or will not
spin. If at the end of the programme the laundry is
not spun enough, redistribute the load manually
and select the spin programme.
• The machine will not dry or the
laundry is not dry enough
• The water tap is closed (E10).
• The drain filter is clogged (E20).
• The drying time or degree of dryness has not been
selected.
• An appropriate drying time or degree of dryness
has not been chosen.
• There is too much laundry inside the appliance.
Water is not
visible in the machine. The machine,
which is the result of modern technology, runs
in a very economical way with low water
consumption. Performance is
nevertheless excellent.
The machine makes an unusual
noise. The machine is fitted with a commutator
motor which improves machine
performance.
P1035UK
P1034UK
Mo
Pro d. .....
d.
No .....
. .....
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning, make
a note of the model, serial number and purchase
date of your machine: the Service Centre will require
this information.
.
Ser
. No
.....
....
. .....
Mod. ..........
Prod. No. ...........
P0042 BD
55
Ser. No. .........
ENGLISH
Problem