Electrolux EDH97980W Basic Guide

user manual
Condenser dryer with heat pump
EDH 97980W
2 electrolux
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Important safety information
Important! In the interest of your safety and
to ensure the correct use, before installing
and first using the appliance, read this user
manual carefully, including its hints and
warnings. To avoid unnecessary mistakes
and accidents, it is important to ensure that
all people using the appliance are thoroughly
familiar with its operation and safety features.
Save these instructions and make sure that
they remain with the appliance if it is moved
or sold, so that everyone using it through its
life will be properly informed on appliance use
and safety.
- Please read the instruction book before
using this appliance.
General safety
• It is dangerous to alter the specifications or attempt to modify this product in any way.
• This appliance is not intended for use by persons (including children) with reduced physical
and sensory conditions or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Make sure that small children and pets do not
climb inside the drum. To avoid this, please
check into the drum before using.
• Any objects such as coins, safety pins, nails,
screws, stones or any other hard, sharp material
can cause extensive damage and must not be
placed into the machine.
• In order to avoid danger of fires caused by excessive drying, do not use appliance to dry the
following items: Cushions, quilts and the like
(these items accumulate heat).
• Items such as foam rubber (latex foam), shower
caps, waterproof textiles, rubber backed articles
and clothes or pillows fitted with foam rubber
pads should not be dried in the tumble dryer.
• Always unplug the appliance after use, cleaning
and maintenance.
• Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Contact your local Service Centre. Always insist on genuine spare parts.
• Items that have been soiled with substances
such as cooking oil acetone, petrol, kerosene,
spot removers, turpentine, waxes and wax removers should be washed in hot water with an
extra amount of detergent before being dried in
the tumble dryer.
• Danger of explosion: Never tumble dry items
that have been in contact with inflammable solvents (petrol, methylated spirits, dry cleaning fluid and the like). As these substances are volatile,
they could cause an explosion. Only tumble dry
items washed with water.
• Risk of fire: items that have been spotted or
soaked with vegetable or cooking oil constitute
a fire hazard and should not be placed in the
tumble dryer.
• If you have washed your laundry with stain remover you must execute an extra rinse cycle
before loading your tumble dryer.
• Please make sure that no gas lighters or matches have accidentally been left in pockets of garments incase they are loaded into appliance
Warning!
• Risk of fire! Never stop a tumble dry
before the end of the drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated.
• Lint must not be allowed to accumulate
around the tumble dryer.
• Risk of electric shock! Do not spray down the
appliance with jets of water.
• The final part of a tumble dryer cycle occurs
without heat ( cool down cycle ) to ensure that
the items are left at a temperature that ensures
that items will not be damaged.
• The tumble dryer is not to be used if industrial
chemicals have been used for cleaning.
• Ensure you have good ventilation in the installation room to avoid the back flow of gases into
the room from appliances burning other fuels,
including open fires.
Installation
• This appliance is heavy. Care should be taken
when moving it.
• When unpacking the appliance, check that it is
not damaged. If in doubt, do not use it and contact the Service Centre.
• All packaging must be removed before use. Serious damage can occur to the product and to
property if this is not adhered to. See relevant
section in the user manual.
• Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
electrolux 3
• If the machine is situated on a carpeted floor,
please adjust the feet in order to allow air to circulate freely under the appliance.
• After having installed the appliance, check that
it is not pressing or standing on its electrical
supply cable.
• If the tumble dryer is placed on top of a washing
machine, it is compulsory to use the stacking kit
(optional accessory).
Use
• This appliance is designed for domestic use. It
must not be used for purposes other than those
for which it was designed.
• Only wash fabrics which are designed to be machine dried. Follow the instructions on each garment label.
• Do not dry unwashed items in the tumble dryer.
• Do not overload the appliance. See the relevant
section in the user manual.
• Clothes which are dripping wet should not be
placed in the dryer.
• Garments which have been in contact with volatile petroleum products should not be machine
dried. If volatile cleaning fluids are used, care
should be taken to ensure that the fluid is removed from the garment before placing in the
machine.
• Never pull the power supply cable to remove the
plug from the socket; always take hold of the
plug itself.
• Never use the tumble dryer if the power supply
cable, the control panel, the working surface or
the base are damaged so that the inside of the
tumble dryer is accessible.
• Fabric softeners, or similar products should be
used as specified by the fabric softener instructions.
• Caution - hot surface : Do not touch the door
light cover surface when the light is switched on.
(Only dryers equipped with internal drum light)
Child safety
• This machine is not intended for use by young
children or infirm persons without supervision.
• Children often do not recognise the hazards associated with electrical appliances. Children
should be supervised to ensure that they do not
play with the appliance.
Warning!
• Danger of suffocation! The packaging
components (e.g. plastic film, polystyrene)
can be dangerous to children - Keep them
out of children’s reach.
• Keep all detergents in a safe place out of children’s reach.
• Make sure that children or pets do not climb inside the drum.
Environment
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of
electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help
prevent potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product, please
contact your local council, your household waste
disposal service or the shop where you purchased
the product.
Environmental tips
• In the dryer, laundry becomes fluffy and soft.
Fabric softeners are not therefore needed when
washing.
• Your dryer will function most economically if you:
– Always keep the ventilation slots on the base
of the dryer unobstructed;
– Use the loading volumes specified in the programme overview;
– Ensure you have good ventilation in the installation room;
– Clean the micro-fine filter and fine strainer after each drying cycle;
– Spin the laundry well before drying.
Energy consumption depends on spinning
speed set in washing machine. Higher spinning speed - lower energy consumption.
Environmental information
The packaging materials are environmentally
friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<,
etc. Please dispose of the packaging materials in
the appropriate container at the community waste
disposal facilities.
Important! The heat pump of your dryer contains
a closed refrigerant circuit filled with a refrigerant
which is free from fluoro-chloro-hydrocarbons.
The refrigerant circuit in the heat pump must not
be damaged.
4 electrolux
Warning! When a unit is no longer being
used:
• Pull the plug out of the socket.
• Cut off the cable and plug and dispose of them.
• Dispose of the door catch. This prevents children from trapping themselves inside and endangering their lives.
Installation
Transporting the appliance
Important! Only tip the appliance on its left side
to transport (see illustration), if it cannot be
transported in an upright position.
• The appliance must not be installed behind the
lockable door, a sliding door a door with a hinge
on the opposite side to that of the appliance in
such a way that a full opening of the dryer is restricted.
Removing transport safety packaging
Caution!
Before use all parts of the transport packaging
must be removed.
Warning! If the appliance was not
transported in an upright position, leave it to
stand for 12 hours before connecting it to the
electricity supply and using it for the first time, so
that the oil can flow back to the compressor.
Otherwise the compressor could be damaged.
Appliance positioning
• It is recommended that, for your convenience,
the machine is positioned close to your washing
machine.
• The tumble dryer must be installed in a clean
place, where dirt does not build up.
• Air must be able to circulate freely all round the
appliance. Do not obstruct the front ventilation
grille or the air intake grilles at the back of the
machine.
• To keep vibration and noise to a minimum when
the dryer is in use, it should be placed on a firm,
level surface.
• Once in its permanent operating position, check
that the dryer is absolutely level with the aid of a
spirit level. If it is not, raise or lower the feet until
it is.
• The feet must never be removed. Do not restrict
the floor clearance through deeppile carpets,
strips of wood or similar. This might cause heat
built-up which would interfere with the operation
of the appliance.
Important!
• The hot air emitted by the tumble dryer can
reach temperatures of up to 60°C. The appliance must therefore not be installed on floors
which are not resistant to high temperatures.
• When operating the tumble dryer, the room temperature must not be lower than +5°C and higher than +35°C, as it may affect the performance
of the appliance.
• Should the appliance be moved, it must be
transported vertically.
1. Open loading door
2. Pull off adhesive strips from inside machine on
top of drum.
3. Remove foil hose and polystyrene padding
from the machine.
Electrical connection
Details on mains voltage, type of current and the
fuses required should be taken from the type plate.
The type plate is fitted near the loading aperture
(see “Product description” chapter).
Warning! The manufacturer declines any
responsibility for damage or injury through
failure to comply with the above safety
precautions.
Should the appliance power supply cable need to
be replaced, this must be carried out by our Service Center.
Warning! The power supply cable must be
accessible after installing the machine.
Door reversal
To make it easier to load or unload the laundry, the
door can be reversed.
Warning! The door must only be reversed
by an authorised service engineer.
electrolux 5
Please contact your local Service Force Centre.
The engineer will carry out the door reversal at your
cost.
Special accessories
• stack kit
Available from your Service Force Centre or
your specialist dealer
Installation kit for direct draining of condensate
into a basin, siphon, gully, etc. The condensate
tank then no longer has to be drained, it must
however remain in its intended position in the
machine.
Read carefully the instructions supplied with the
kit.
• pedestal with the drawer
Available from your Service Force Centre or
your specialist dealer
These intermediate installation kits can be used
to arrange the dryer and an washing machine
(60 cm wide, front loaded) as a space-saving
washer/dryer stack. The washing machine is at
the bottom and the dryer is at the top.
Read carefully the instructions supplied with the
kit.
• drain kit
To situate the dryer in optimal high and have
some additional space to store (e.g. laundry).
Read carefully the instructions supplied with the
kit.
Available from your Service Force Centre or
your specialist dealer
Product description
2
1
3
4
5
6
8
7
9
11
10
13
12
1 Control panel
2 Water reservoir
3 Drum light
4 Fine fluff filters
5 Fluff filters
6 Loading door (reversible)
7 Push button for base door opening
8 Course fluff filters
9 Rating plate
10 Fluff filter
11 Ventilation grille
12 Heat exchanger door
13 Adjustable feet
Control panel
5
6
7
8
9
Control panel
Long Anticrease button
Buzzer button
Time button
Start/Pause button
Warning lights:
Full tank
10 Delay button
1
2
3
4
5
6 7
8
9 10
1 Programme selector and
off switch
2 Display
3 Wool/Silk programme selection button
4 Dryness button
Condenser ,
Filters ,
6 electrolux
Display
SYMBOL
DESCRIPTION
Auto dryness level
Time to end (time of time programm, time of start delay)
SYMBOL
Cycle performans, auto dryness detection
DESCRIPTION
Wool/Silk not selectable
Long anti-crase guard
Wool or Silk programme selection mode
Child lock
Wool programme selection
Delay start
Alarm
Drying phase
Silk programme selection
Cooling phase
Anticrease guard phase
Minimal dryness level
Error, wrong selection
Medium dryness level
Maximal dryness level
Before first use
Warning! If the appliance was not
transported in an upright position, leave it to
stand for 12 hours before connecting it to the
electricity supply and using it for the first time, so
that the oil can flow back to the compressor.
Otherwise the compressor could be damaged.
drum with a damp cloth or carry out a brief drying
cycle (30 min.) with damp cloths in the machine.
1. Turn the programme knob to
Time.
2. Press the Time button repeatedly until
appears in the display.
3. Press the Start/Pause button.
In order to remove any residues which may have
been produced during production, wipe the dryer
Cottons
Extra
7 kg
Thorough drying of thick or multi- layered fabrics,
e.g. terry towelling items, bathrobes.
Dryness,
Long anticrease,
Buzzer,
Delay
Care label
Application/properties
Options
Programme
max. load
(dry clothes)
Programme chart
Strong
Cupboard
Damp
Iron
7 kg
Thorough drying of thick fabrics, e.g. terry towelling
items, towels.
Dryness,
Long anticrease,
Buzzer,
Delay
7 kg
Thorough drying of fabrics of even thicknesses, e.g.
terry towelling items, knitwear, towels.
Dryness,
Long anticrease,
Buzzer,
Delay
7 kg
For thin fabrics which are also to be ironed, e.g. knitwear, cotton shirts.
Dryness,
Long anticrease,
Buzzer,
Delay
7 kg
For thin fabrics which are also to be ironed, e.g. knitwear, cotton shirts.
Dryness,
Long anticrease,
Buzzer,
Delay
Synthetics
Extra
Cupboard
Iron
3 kg
Thorough drying of thick or multi-layered fabrics, e.g.
pullovers, bedding, table linen.
Dryness,
Long anticrease,
Buzzer,
Delay
3 kg
For thin fabrics which are not ironed, e.g. easy care
shirts, table linen, baby clothes, socks, lingerie with
bones or wires.
Dryness,
Long anticrease,
Buzzer,
Delay
3 kg
For thin fabrics which are also to be ironed, e.g. knitwear, cotton shirts.
Dryness,
Long anticrease,
Buzzer,
Delay
Special
Time
Mix
7 kg
Long anticrease,
For further drying of individual items of laundry. (DryBuzzer,
ness (Dryness) function not available)
Time, Delay
3 kg
Dryness,
Long anticrease,
Buzzer,,
Delay
For drying cotton and synthetic fabrics, uses low
temperature.
Care label
Application/properties
Options
Programme
max. load
(dry clothes)
electrolux 7
Jeans
Wool
Silk
Cooling
1 kg
(or 5
shirt
s)
Special program with anti-crease mechanism for
easy care fabrics such shirts and blouses; for minimum ironing effort. The results depends on the type
of fabric and its finish. Place fabrics in the dryer
straight after spinning; once dried, immediately remove fabrics and place on a clothes hanger.
Dryness,
Long anticrease,
Buzzer,,
Delay
7 kg
For leisure clothing, such as jeans, sweat-shirts, etc.,
of different material thicknesses (e.g. at the neck,
cuffs and seams).
Dryness,
Long anticrease,
Buzzer,,
Delay
1 kg
For drying woollen fabrics after they have been
Wool/Silk,
washed, using warm air at minimum mechanical load
Dryness,
(Follow section “Sorting and preparing washing”).
Buzzer,
Recommendation: Remove fabrics immediately after
Delay
drying, as no anti-crease programme follows.
1 kg
Wool/Silk,
Dryness,
Long antiFor drying silk using warm air and gentle movement.
crease,
Buzzer,
Delay
1 kg
Special programme, lasting around 10 minutes, for
refreshing or gently cleaning textiles with commercially available dry cleaning sets. (Only use those
products which are declared as suitable for the drier
by the manufacturer; please observe the manufacturer’s instructions for use.)
Care label
Easy
Application/properties
Options
Programme
max. load
(dry clothes)
8 electrolux
Buzzer
Daily use
Sorting laundry
• Sort by fabric type:
– Cotton/linen for programmes in
Cottons
programme group.
– Mixtures and synthetics for programmes in
Synthetics programme group.
• Sort by care label: The care labels mean:
Drying in the tumble dryer possible in
principle
Drying at normal temperature
Drying at reduced temperature
Drying in the tumble dryer not possible
Important! Do not place in the appliance any wet
laundry which is not specified on the care label as
being suitable for tumble-drying.
This appliance can be used for all wet laundry
items which are labelled as suitable for tumbledrying.
• Do not dry new, coloured textiles together with
light-coloured laundry items. Textile colours may
bleed.
• Do not dry cotton jersey and knitwear with the
Extra programme. Items may shrink!
• Wool and wool-like textiles can be dried using
the
Wool programme. Before the drying
cycle spin the woollen textiles as well as possible
(max. 1200 rpm). Only dry woollen textiles together of similar or the same material, colour and
weight. Please dry heavy laundry items made of
wool separately.
Preparing laundry
• To avoid laundry becoming tangled: close zips,
button up duvet covers and tie loose ties or ribbons (e.g. of aprons).
electrolux 9
• Empty pockets. Remove metal items (paper
clips, safety pins, etc).
• Turn items with double-layered fabrics inside out
(e.g. with cotton-lined anoraks, the cotton layer
should be outermost). These fabrics will then dry
better.
Important! Do not overload the appliance.
Observe max. loading volume of 7 kg.
Switching machine on
Turn the programme selector to any programme.
The machine switches on. When the loading door
is open, the internal lamp illuminates the drum.
increases the dryness of the dried laundry adequately to the selected level:
- maximum
- medium
- minimum
- inactive with some programmes
this option helps to achieve satisfying result of
drying
Operating
Long anti-crease
prolongs anti-crease phase to 90 min., helps to
keep laundry free from creases after drying;
laundry can be removed at any time
Buzzer
audible confirmation of:
• cycle end
• anti-crease phase start and end
• cycle interruption
• error
Time
allows to set individual time of drying from minimum 20 min. to maximum of 3 hours (in 10 min.
steps - press the button repeatedly until the desired programme duration is shown in the dis- for a programme of 1
play, e.g.
hour and 20 minutes ); active with suitable programme
Drying options
Wool/Silk
type of laundry (only with
gramme):
- Wool
- Silk
Dryness
Delay
Wool/Silk pro-
allows to delay the start of a drying programme
from minimum of 30 min. to maximum of 20
hours
1. select the drying programme and additional
drying options
2. press the Delay button repeatedly until the
desired delay start is shown on the display,
H if the programme has to start
e.g.
after time of 12 hours
3. to activate the delay timer, press the Start/
Pause button - time to start elapses on the
display
Setting child lock
The child lock can be set to prevent a programme
being accidentally started or a programme in operation being accidentally changed. The child lock
function locks all buttons and the programme selector. The child lock can be activated or deacti-
10 electrolux
vated by holding down the Buzzer and Time buttons simultaneously for 5 seconds.
The symbol
on the display means that the child
lock is active.
as well as warning lamps:
filter and
full tank . If the Buzzer button has been pressed, an acoustic signal sounds intermittently for
about one minute.
Any changes of drying parameters require
child lock deactivation.
The child lock cannot be deactivated in the last
phase of the drying cycle.
The drying cycles are automatically followed
by an anti-crease phase which lasts around
30 minutes. The drum rotates at intervals during
this phase. This keeps the laundry loose and free
of creases. The laundry can be removed at any
time during the anti-crease phase. (The laundry
should be taken out towards the end of the anticrease phase at the latest to prevent creases from
forming.)
Starting the programme
Press the Start/Pause button. The programme
starts.
The programme progress is shown by elapsing dry
time on the LCD.
Changing programme
To change a programme which has been selected
by mistake once the programme has started, first
turn the programme selector to
off and then
reset the programme.
The programme can no longer be changed
directly once the programme has started. If
nevertheless there is an attempt to change the
programme on the programme knob, the programme progress display and the maintenance indicators flash. If an option button (excluding the
appears on the
Buzzer button) is pressed,
display. The drying programme is not however affected by this (laundry protection).
1. Open door.
2. Before removing the laundry, remove fluff from
the micro-fine filter. It is best to use a damp
hand for this purpose. (See “Maintenance and
cleaning” chapter.)
3. Remove laundry.
4. Turn the programme selector to
off .
Important! After each drying cycle:
- Clean the micro-fine filter and fine filter
- Drain the condensed water container
(See chapter “Maintenance and cleaning ”.)
5. Close the door.
Drying cycle complete / removing laundry
Once the drying cycle is complete, the display
shows the anti-crease icon
and flashing
Cleaning and maintenance
Cleaning fluff filters
The filters collect all the fluff which accumulates
during drying. To ensure that the dryer works perfectly, the fluff filters (fine filters and fluff filters) must
be cleaned after each drying cycle.
Caution! Never operate the dryer without
fluff filters or with damaged or blocked fluff
filters.
1
2
3
4
1
2
3
4
electrolux 11
Clean the door seal
Wipe the door seal with a damp cloth immediately
after the drying cycle has finished.
Emptying the water reservoir
Empty the water reservoir after every drying cycle.
Warning! The condensed water is not
suitable for drinking or for preparing
foodstuffs.
If the programme has been interrupted as a
result of the water reservoir being full: Press
the Start/Pause button to continue the drying cycle.
Cleaning heat exchanger filter
Important!
• Never operate the dryer without the fluff filters.
• Clogged filters cause higher energy consumption (drying cycle elongation) and dryer damage.
• A dirty heat pump can only be cleaned up by
means of a costly process.
• As necessary, approx. once every 6 months, remove the fluff from the heat exchanger using the
sponge supplied. When doing this, please use
rubber gloves (picture 7).
Cleaning the drum
Caution! Do not use abrasives or steel wool
to clean the drum.
Lime in the water or cleaning agents may
form a barely visible lining on the inside of the
drum. The degree to which the laundry has been
dried is then no longer detected reliably. The laundry is damper than expected when removed from
the appliance.
Use a standard domestic cleaner (e.g. vinegarbased cleaner) to wipe down the inside of the drum
and drum ribs.
Clean control panel and housing
Caution! Do not use furniture cleaners or
aggressive cleaning agents to clean the
machine.
12 electrolux
Use a damp cloth to wipe down the control panel
and housing.
What to do if ...
Troubleshooting by yourself
Problem 1)
Dryer does
not work.
Unsatisfactory
drying results.
Possible cause
Remedy
Dryer not connected to mains supply.
Plug in at mains socket. Check fuse in
fuse box (domestic installation).
Loading door opened.
Close loading door
The START PAUSE button not pressed.
Press the START PAUSE button.
Incorrect programme set.
Set suitable programme. 2)
Fluff filters clogged.
Clean fluff filters. 3)
Heat exchanger clogged.
Clean heat exchanger. 3)
Max. loading exceeded.
Respect max. loading volume.
Covered ventilation grill.
Uncover ventilation grill in base area.
Residue inside the drum.
Clean the drum inside.
High water hardness.
Set suitable water hardness4).
Loading door
Filters not locked in place.
does not close
Install fine filter and/or snap course filter
into place.
Err ( Error ) on
the LCD.5)
Attempt to change parameters after start
of the programme.
Turn the dryer off and on. Set requested
parameters.
Programme selector in OFF position.
Turn it to DRUM LIGHT (if available) or to
any programme.
No drum light
Defective light bulb.
Replace light bulb (see next section).
Abnormally
elapsing time
on the LCD5)
Time to end is calculated on the basis of:
type, volume and dampness of laundry.
Automatic process; this is not a machine
fault.
Programme
inactive
Full water reservoir.
Empty water reservoir3) , press START
PAUSE button.
Drying cycle
to short
Small laundry volume./Too dry laundry for
selected programme.
Select time programme or higher drying
level (e.g. EXTRA DRY).
Fluff filters clogged.
Clean fluff filters.
To high loading volume.
Respect max. loading volume.
Laundry insufficiently spun.
Spun adequately the laundry.
Particularly high room temperature - no
machine fault.
Lower the room temperature if possible.
Drying cycle
to long 6)
1) In case of error message on the LCD (e.g. E51 - only dryers with the LCD): Switch the dryer off and
on. Set programme. Press the START PAUSE button. Does not work? - inform local service and quote
the error code.
2) follow program recommendation - see Programme overview chapter
3) see Care and cleaning chapter
4) see Machine settings chapter
5) only dryers with the LCD
6) Note: After around 5 hours the drying cycle ends automatically (see Drying cycle complete section).
electrolux 13
Changing the bulb for interior lighting
Only use a special bulb which is designed specially
for dryers. The special bulb can be obtained from
your local service centre.
Important! When the appliance is switched on,
the interior lighting switches itself off after 4
minutes when the door is open.
Warning! Do not use standard bulbs! These
develop too much heat and may damage the
machine!
Before replacing the bulb, disconnect the mains
plug; with a permanent connection: fully unscrew
or deactivate the fuse.
1. Unscrew cover above the bulb (this can be
found directly behind the loading aperture, at
the top; refer to “Description of machine” section.)
2. Replace defective bulb.
3. Screw cover back down.
Check the correct positioning of o-ring gasket before screwing back the door light cover. Do not
operate the dryer when missing o-ring gasket on
door light cover.
Warning! For safety reasons, the cover must
be screwed down tightly. If this is not done,
the dryer must not be operated.
Technical specifications
Height x width x depth
85 x 60 x 58 cm
Drum volume
108 l
Depth with loading door open
109 cm
Height can be adjusted by
1.5 cm
Weight when empty
approx. 56 kg
Loading volume (depends on programme)1)
max. 7 kg
Voltage
230 V
Required fuse
6A
Total power
1050 W
Energy efficiency class
A
Energy consumption (7 kg of cotton, pre-drained
at 1000 rpm) 2)
1.9 kWh
Average annual energy consumption
126.2 kWh
Use
Domestic
Permissible ambient temperature
+ 5°C to + 35°C
Consumption values
The consumption values have been established under standard conditions. They may deviate when
the machine is operated in domestic circumstances.
Programme
Energy consumption in kWh / average drying
time in min.
COTTON CUPBOARD DRY3)
1.9/ 135 (7 kg load pre-drained at 1000 rpm)
1.7 (7 kg load pre-drained at 1200 rpm)
1.65 (7 kg load pre-drained at 1400 rpm)
1.42 (7 kg load pre-drained at 1800 rpm)
COTTON IRON DRY3)
1.4/ 106 (7 kg load pre-drained at 1000 rpm)
SYNTHETICS CUPBOARD DRY3)
0.59/ 48 (3 kg load pre-drained at 1200 rpm)
1) different loading volume data may be needed in some countries as a result of different measuring
methods
2) in accordance to EN 61121
3) hints for test institutes: cycle has to be checked in accordance to EN 61121
14 electrolux
Machine settings
Setting
Implementation
Buzzer permanent
on/off
The alarm is by default always off. To set permanent alarm on (off):
1. Turn the programme selector to any programme.
2. Press simultaneously the Dryness and Long anti-crease buttons and hold
down for approx. 5 seconds.
Water hardness 1)
1. Turn the programme selector to any programme.
2. Press simultaneously the Long anti-crease and Start/Pause buttons and
hold down for approx. 5 seconds.
3. Press the Start/Pause button until you set desired level:
- low conductivity <300 μS/cm
- medium conductivity 300-600 μS/cm
- high conductivity >600 μS/cm
4. To memorize setting press simultaneously the Long anti-crease and
off position
Start/Pause buttons or turn knob to
1) Water contains, a variable quantity of limestone and mineral salts of which quantities vary according
to geographical locations thus varying its conductivity values. Relevant variations of the conductivity
of the water compared to those prefixed by the factory could slightly influence the residual humidity
of the laundry at the end of the cycle. Your dryer allows you to regulate the sensitivity of the drying
sensor based on conductivity values of the water.
electrolux 15
www.electrolux.com
136911070-00-092009
">