advertisement
▼
Scroll to page 2
of 20
EN User Manual Washing Machine ZWSO7100VS Contents Safety information Safety Instructions Product description Control panel Programme Chart Consumption values Options 2 3 4 5 6 8 8 Settings Before first use Daily use Hints and tips Care and cleaning Troubleshooting Technical Data 9 9 9 12 13 15 17 Subject to change without notice. Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. Children and vulnerable people safety • • • • • • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Do not let children play with the appliance. Keep all packaging away from children. Keep all detergents away from children. Keep children and pets away from the appliance door when it is open. Cleaning and user maintenance shall not be made by children without supervision. General Safety • • • 2 Do not change the specification of this appliance. Obey the maximum load volume of 4 kg (refer to the “Programme chart” chapter). The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa). www.zanussi.com • • • • • • The ventilation openings in the base (if applicable) must not be obstructed by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects. Safety Instructions Installation • • • • • • • • • • • • Remove all the packaging and the transit bolts. Keep the transit bolts. When you move the appliance again you must block the drum. Always be careful when you move the appliance because it is heavy. Always wear safety gloves. Do not install or use a damaged appliance. Obey the installation instruction supplied with the appliance. Do not install or use the appliance where the temperature is less than 0 °C or where it is exposed to the weather. Make sure that the floor where you install the appliance is flat, stable, heat resistant and clean. Do not install the appliance where the appliance door can not be fully opened. Make sure that there is air circulation between the appliance and the floor. Adjust the feet to have the necessary space between the appliance and the carpet. Electrical Connection • • • The appliance must be earthed. Always use a correctly installed shockproof socket. Make sure that the electrical information on the rating plate agrees with the power supply. If not contact an electrician. www.zanussi.com • • • • • Do not use multi-plug adapters and extension cables. Make sure not to cause damage to the mains plug and to the mains cable. Should the mains cable need to be replaced, this must be carried out by our Authorised Service Centre. Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. Do not touch the mains cable or the mains plug with wet hands. Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. Only for UK and Ireland: The appliance has a 13 amp mains plug. If it is necessary to change the fuse in the mains plug, use a 13 amp ASTA (BS 1362) fuse. This appliance complies with the E.E.C. Directives. Water connection • • • Make sure not to cause damage to the water hoses. Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. The first time you use the appliance, make sure that there is no leakage. 3 Use WARNING! • Risk of injury, electrical shock, fire, burns or damage to the appliance. • • • • • Use this appliance in a household only. Obey the safety instructions on the detergent packaging. Do not put flammable products or items that are wet with flammable products in, near or on the appliance. Make sure that you remove all metal objects from the laundry. Do not put a container to collect possible water leakage under the appliance. Contact the Authorised Service Centre to ensure which accessories can be used. Do not touch the glass of the door while a programme operates. The glass can be hot. Disposal WARNING! Risk of injury or suffocation. • • • Disconnect the appliance from the mains supply. Cut off the mains cable and discard it. Remove the door catch to prevent children and pets to get closed in the appliance. Product description Appliance overview 1 2 1 2 3 4 5 6 7 3 Worktop Detergent dispenser Control panel Door handle Rating plate Drain pump filter Feet for the appliance level 4 5 6 7 4 www.zanussi.com Control panel Control panel description 1 2 10 1 Programme knob 2 Display 3 Delay Start button (Отложенный старт) 9 8 7 6 3 4 5 7 Super quick button (Супер Быстрый) 8 Rinse Hold button (Остановка полоскания) 9 Spin reduction button (Отжим) 4 Door locked indicator 5 Start/Pause button (Старт/Пауза) 10 Temperature button (Температура) 6 Extra Rinse button (Доп. полоскание) Display A B C A) The delay start . When you press the delay start button, the display shows the delay start time. B) The child lock indicator. The indicator comes on the display when the related option is set. C) This area shows: • The programme time. • The alarm codes. If the appliance has a malfunction, the display shows the alarm codes. Refer to the chapter 'Troubleshooting' . • The display shows the message for some seconds if: – You set a option that is not suitable for the programme. – You change the programme while it operates. The display shows: www.zanussi.com 5 Programme Chart Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) Washing programmes Хлопок 4 kg 1000 rpm White cotton and coloured cotton. Normal soil and light soil. 4 kg 1000 rpm White cotton and coloured cotton. Heavy soil and normal soil. 4 kg 1000 rpm White cotton and colour-fast cotton. Normal soil. The energy consumption decreases and the time of the washing programme is extended. 2 kg 1000 rpm Synthetic items or mixed fabric items. Normal soil. 3 kg 1000 rpm Special programme for cotton, synthetic and mixed fabrics with light soil. Set this programme to decrease the energy consumption. Make sure that the detergent is for low temperature in order to have good washing results 2). 2 kg 700 rpm Delicate fabrics as acrylics, viscose, polyester items. Normal soil. 1.5 kg 1000 rpm Machine washable wool, hand washable wool and delicate fabrics with «hand washing» care symbol. 3) Полоскание 4 kg 1000 rpm To rinse and spin the laundry. All fabrics. Слив 4 kg To drain the water in the drum. All fabrics. Отжим 4 kg 1000 rpm To spin the laundry and to drain the water in the drum. All fabrics. Легкая глажка 1 kg 700 rpm Synthetic items to be gentle washed. Normal and light soil. 90°C - (Cold) Хлопок + Предв. стирка 90°C - (Cold) Хлопок Eco 1) 60°C - 40°C Синтетика 60°C - (Cold) Mикc 20° 20°C Тонкие ткани 40°C - (Cold) Шерсть/Ручная стирка 40°C - 60°C - 6 (Cold) (Cold) 4) 5 pубашек 30°C 700 rpm Synthetic and mixed fabric items. Light soil items and items to freshen up. For 5 - 6 shirts. Mини 30 30°C 2 kg 700 rpm Synthetic and delicate items. Light soil items or items to refresh. www.zanussi.com Programme Temperature range Джинсы 60°C - (Cold) Maximum load Maximum spin speed 4 kg 1000 rpm Programme description (Type of load and soil level) Items in denim and jersey. Also for dark coloured items. 1) Cottons energy saving programme. This programme at a 60ºC with a load of 4 is the reference programme for data entered in the energy label, in compliance with EEC 92/75 standards. Set this programme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended. 2) The appliance performs the short heating phase if the water temperature is below 20°C. The appliance can show the temperature setting as “cold”. 3) During this cycle the drum rotates slowly to ensure a gentle washing. It can seem that the drum doesn't rotate or doesn't rotate properly. Consider this as a normal functioning of the appliance. 4) To reduce the creases of the laundry, this cycle regulates the water temperature and performs a soft wash and spin phase. The appliance adds some rinses. Programme options compatibility Programme Отжим Остано вка полоска ния Супер Быстры й 1) Доп. полоска ние 2) Отложе нный старт Хлопок ■ ■ ■ ■ ■ Хлопок + Предв. стирка ■ ■ ■ ■ ■ ■ ■ ■ ■ Синтетика ■ ■ ■ ■ Mикc 20° ■ ■ ■ ■ Тонкие ткани ■ ■ ■ ■ Шерсть/Ручная стирка ■ ■ Полоскание ■ ■ Хлопок Eco ■ ■ ■ ■ ■ Слив Отжим ■ ■ Легкая глажка ■ 5 pубашек ■ ■ Mини 30 ■ ■ Джинсы ■ ■ ■ ■ ■ ■ ■ 1) If you set a shorter duration, we recommend that you decrease the quantity of the load. It is possible to load fully the appliance, however the washing results are reduced. 2) If you set Extra Rinse option, the appliance adds some additional rinses. In the Rinse programme, if you set a low spin speed the appliance performs delicate rinses and a short spin. www.zanussi.com 7 Consumption values The data of this table are approximate. Different causes can change the data: the quantity and type of laundry, the water and ambient temperature. Programmes Load (kg) Energy consumption (kWh) Water consumption (litre) Approximate programme duration (minutes) Cottons 60 °C 4 0.59 34 125 Cotton Energy Saving Programme 60 °C 1) 4 0.66 46 183 Cottons 40 °C 4 0.55 38 117 Synthetics 40 °C 2 0.39 41 64 Delicates 40 °C 2 0.45 51 47 1.5 0.40 61 40 Wool/Handwash 30 °C 1) «Cotton Energy Saving programme » at 60°C with a load of 4 kg is the reference programme for the data entered in the energy label, in compliance with EEC 92/75 standards. Off Mode (W) Left On Mode (W) 0,48 0,48 The information given in the chart above are in compliance with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC. Options Температура • With this option you can change the default temperature. • Indicator = cold water. The indicator of the set temperature comes on. Отжим With this option you can change the default spin speed. • There is a water in the drum when the programme is completed. The drum turns regularly to prevent the laundry creases. The door stays locked. You must drain the water to unlock the door. To drain the water refer to ‘At the end of the programme’. Супер Быстрый The indicator of the set speed comes on. Press this button to decrease the programme duration. Остановка полоскания Set this option for items with light soil or items to refresh. • • 8 Set this option to prevent the laundry creases. The related indicator comes on. www.zanussi.com Доп. полоскание Door locked indicator With this option you can add some rinses to a washing programme. With this option you can delay the start of a programme from 30 minutes to 20 hours. Use this option for persons allergic to detergents and in areas where the water is soft. The indicator shows when the door can be opened: • The indicator is on: the door cannot be opened. • The indicator flashes: the door is opening in some minutes. • The indicator is off: the door can be opened. The related indicator comes on. Отложенный старт With this option you can delay the start of a programme from 30 minutes to 20 hours. The display shows the related indicator. Settings Child Lock With this option you can prevent that the children play with the control panel. • To activate/deactivate this option, press Температура and Отжим at the same time until the indicator comes on/goes off. You can activate this option: • • After you press Старт/Пауза: the options and the programme knob are locked. Before you press Старт/Пауза: the appliance cannot start. Acoustic signals The acoustic signals operate when: • • The appliance has a malfunction. To deactivate/activate the acoustic signals, press Ocтанoвка полоскания and Cyпep Быстрый at the same time for 6 seconds. The programme is completed. If you deactivate the acoustic signals, they continue operate when the appliance has a malfunction. Extra Rinse With this option you can permanently have an extra rinse when you set a new programme. • To activate/deactivate this option touch the buttons Ocтанoвка полоскания and Доп. полоскание at the same time until the indicator comes on/goes off. Before first use 1. Put a small quantity of detergent in the compartment for washing phase. 2. Set and start a programme for cotton at the highest temperature without laundry. This removes all possible dirt from the drum and the tub. Daily use WARNING! Refer to Safety chapters. Loading the laundry Open the water tap. Connect the mains plug to the mains socket. 1. Pull the door handle to open the appliance door. www.zanussi.com 2. Put the laundry in the drum, one item at a time. 3. Shake the items before you put them in the appliance. Make sure not to put too much laundry in the drum. Refer to max. loads indicated in "Programme chart". 4. Close the door. 9 CAUTION! Liquid or powder detergent Pull out the detergent dispenser until it stops. The position A of the detergent divider is for powder detergent. Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. To use liquid detergent: 1. Remove detergent divider from the position A. Using detergent and additives 2 1 1. Measure out the detergent and the fabric conditioner. 2. Carefully close the detergent drawer. Detergent compartments CAUTION! Use only specified detergents for washing machine. Always obey the instructions that you find on the packaging of the detergent products. 1 Detergent compartment for prewash phase or soak programme (if available). Add the detergent for prewash and soak before the start of the programme. 2 Detergent compartment for washing phase. If you use a liquid detergent, put it immediately before you start the programme. Compartment for liquid additives (fabric conditioner, starch). Put the product in the compartment before you start the programme. 10 A 2. Adjust the detergent divider in position B. 3. Carefully close the detergent dispenser. B To use powder detergent again, insert the detergent divider in the position A again. When you use the liquid detergent: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid detergent than the edge of the detergent devider. • Do not set the prewash option. • Do not set the delay start. Setting a programme 1. Turn the programme knob to switch the appliance on and set the programme: • The indicator of the button Старт/ Пауза flashes. • The display shows the programme duration. 2. If necessary, change the temperature and the spin speed or add available options. When you activate an option, the indicator of the set option comes on. www.zanussi.com If you set something incorrect, the display shows the message . Starting a programme without the delay start Press the button Старт/Пауза. • The indicator of the button Старт/ Пауза stops to flash and stays on. • The programme starts, the door locks, the indicator is on. • The programme starts and the door locks. • The programme time decreases with steps of one minute. The drain pump can operate for a short time at the beginning of the washing cycle. Starting a programme with the delay start option 1. Press the button Отложенный старт again and again until the display shows the delay you want to set. The delay start indicator comes on. 2. Press the button Старт/Пауза: The door is locked and the indicator is on. • The appliance starts the countdown. • When the countdown is completed, the programme starts automatically. You can cancel or change the set of the Отложенный старт option before you press the button Старт/ Пауза. After pressing the button Старт/Пауза you can only cancel the Отложенный старт option. 2. Turn the programme knob again to activate the appliance. Now, you can set a new washing programme. Before starting the new programme the appliance drains the water. Make sure that the detergent is still in the detergent compartment, if not fill the detergent again. Interrupting a programme and changing the options You can change only some options before they operate. 1. Press the button Старт/Пауза. The indicator flashes. 2. Change the options. 3. Press the button Старт/Пауза again. The programme continues. Opening the door While a programme or the Отложенный старт operates, the appliance door is locked. The indicator CAUTION! If the temperature and level of the water in the drum are too high and the drum still rotates, you cannot open the door. • To cancel the Отложенный старт option: a. Press the button Старт/Пауза to set the appliance to pause. The indicator of button Старт/Пауза flashes. b. Press the button Отложенный старт until the display shows . Press the button Старт/Пауза again to start the programme immediately. Cancelling a programme 1. Turn the programme knob to position to cancel the programme and to deactivate the appliance. www.zanussi.com is on. To open the door during the first minutes of the cycle or when the Отложенный старт operates: 1. Press the button Старт/Пауза to pause the appliance. 2. Wait until the indicator goes off. 3. You can open the door. 4. Close the door and touch the button Старт/Пауза again. The programme (or the Отложенный старт) continues. At the end of the programme • • The appliance stops automatically. The acoustic signal operates (if it is activated). • • In the display comes on. The indicator of the button Старт/Пауза goes off. • The door lock indicator goes off. 11 Turn the programme knob to position to deactivate the appliance. • You can open the door. • Remove the laundry from the appliance. Make sure that the drum is empty. • Close the water tap. • Keep the door and the detergent drawer ajar, to prevent the mildew and odours. The washing programme is completed, but there is water in the drum: • The drum turns regularly to prevent the creases in the laundry. • The indicator Остановка полоскания stays on to remind you to drain the water. • • The door lock indicator is on. The indicator of button Старт/Пауза flashes. The door stays locked. You must drain the water to open the door. Draining the water: 1. To drain the water. Set a Слив or a Отжим programme. Press the button Старт/Пауза. The appliance drains the water and spins. 2. When the programme is completed and the • • door lock indicator goes off, you can open the door. 3. Turn the programme knob to the position to deactivate the appliance. Stand by Some minutes after the end of the washing programme, if you do not deactivate the appliance, the energy saving status activates. The energy saving status decreases the energy consumption when the appliance is on the standby: • All indicators and the display go off. • The indicator of button Start flashes slowly. Press one of the buttons to deactivate the energy saving status. Hints and tips The laundry load Stubborn stains • For some stains, water and detergent is not sufficient. • • • • • • • • • • • 12 Divide the laundry in: white, coloured, synthetics, delicates and wool. Obey the washing instructions that are on the laundry care labels. Do not wash together white and coloured items. Some coloured items can discolour with the first wash. We recommend that you wash them separately for the first times. Button up pillowcases, close zippers, hooks and poppers. Tie up belts. Empty the pockets and unfold the items. Turn inside out multilayered fabrics, wool and items with painted illustrations. Remove hard stains. Wash with a special detergent heavy soil stains. Be careful with the curtains. Remove the hooks or put the curtains in a washing bag or pillowcase. Do not wash in the appliance laundry without hems or with cuts. Use a washing bag to wash small and/or delicate items (e.g. underwired bras, belts, tights, etc. ). A very small load can cause balance problems with the spin phase. If this occurs, adjust manually the items in the tub and start the spin phase again. We recommend that you remove these stains before you put the items in the appliance. Special stain removers are available. Use the special stain remover that is applicable to the type of stain and fabric. Detergents and additives • • • • • Only use detergents and additives specially made for washing machines: – powder detergents for all types of fabric, – powder detergents for delicate fabrics (40 °C max) and woollens, – liquid detergents, preferably for low temperature wash programmes (60 °C max) for all types of fabric, or special for woollens only. Do not mix different types of detergents. To help the environment, do not use more than the correct quantity of detergent. Obey the instructions that you find on the on packaging of these products. Use the correct products for the type and colour of the fabric, the programme temperature and the level of soil. www.zanussi.com • If your appliance has not the detergent dispenser with the flap device, add the liquid detergents with a dosing ball (supplied by the detergent's manufacturer). Ecological hints • • • • Set a programme without the prewash phase to wash laundry with normal soil. Always start a washing programme with the maximum load of laundry. If necessary, use a stain remover when you set a programme with a low temperature. To use the correct quantity of the detergent, check the water hardness of your domestic system Water hardness If the water hardness in your area is high or moderate, we recommend that you use a water softener for washing machines. In areas where the water hardness is soft it is not necessary to use a water softener. To know the water hardness in your area, contact your local water authority. Use the correct quantity of the water softener. Obey the instructions that you find on the packaging of the product. Care and cleaning WARNING! Door seal Refer to Safety chapters. Regularly examine the seal and remove all objects from the inner part. External cleaning Clean the appliance only with soap and warm water. Fully dry all the surfaces. CAUTION! Do not use alcohol, solvents or chemical products. Descaling If the water hardness in your area is high or moderate, we recommend that you use a water softener for washing machines. Cleaning the detergent dispenser 1 2 3 4 Regularly examine the drum to prevent limescale and rust particles. To remove rust particles use only special products for washing machine. Do this separately from the laundry wash. Always obey the instructions that you find on the packaging of the product. Maintenance wash With the low temperature programmes it is possible that some detergent stays in the drum. Make regularly a maintenance wash. To do this: • • Remove the laundry from the drum. Set the cotton programme with the highest temperature with a small quantity of detergent. www.zanussi.com 13 5 6 9 10 2 Cleaning the detergent dispenser 1 2 1 Cleaning the inlet hose and the valve filter 1 1 2 2 3 3 4 3 4 45° 20° 5 1 6 Because of a malfunction, the appliance cannot drain the water. 2 7 Emergency drain If this occurs, do steps (1) through (10) of 'Cleaning the drain filter'. If necessary, clean the pump. 8 When you drain the water with the emergency drain procedure, you must activate again the drain system: 1. When you drain the water with the emergency drain procedure, you must activate again the drain system: Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water Frost precautions If the appliance is installed in an area where the temperature can be less than 0° C, remove the 14 www.zanussi.com remaining water from the inlet hose and the drain pump. 5. When the drain pump is empty, install the inlet hose again. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Close the water tap. 3. Put the two ends of the inlet hose in a container and let the water flow out of the hose. 4. Empty the drain pump. Refer to the emergency drain procedure. Make sure that the temperature is more than 0 °C before you use the appliance again. The manufacturer is not responsible for damages caused by low temperatures. Troubleshooting WARNING! • Refer to Safety chapters. • Introduction - The appliance does not fill with water properly. water. - The appliance does not drain the The start of the appliance does not occur or it stops during operation. • - The appliance door is open or not closed correctly. Please check the door! First try to find a solution to the problem (refer to the table). If not, contact the Authorised Service Centre. • - The mains supply is unstable. Wait until the mains supply is stable. With some problems, the acoustic signals operate and the display shows an alarm code: WARNING! Deactivate the appliance before you do the checks. Possible failures Problem The programme does not start. Possible solution • • • • • • The appliance does not fill with water properly. • • • • • • • www.zanussi.com Make sure that the mains plug is connected to the mains socket. Make sure that the appliance door is closed. Make sure that there is not a damaged fuse in the fuse box. Make sure that the Start/Pause has been pressed. If the delay start is set, cancel the setting or wait for the end of countdown. Deactivate the Child Lock function if it is on (if available). Make sure that the water tap is open. Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. Make sure that the water tap is not clogged. Make sure that the filter of the inlet hose and the filter of the valve are not clogged. Refer to “Care and cleaning”. Make sure that the inlet hose has no kinks or bends. Make sure that the connection of the water inlet hose is correct. Make sure that the drain hose is in the correct position. The hose may be too low. 15 Problem The appliance does not drain the water. Possible solution • • • • • • • • The spin phase does not operate or the washing cycle lasts longer than usually. • There is water on the floor. • • • Make sure that the sink spigot is not clogged. Make sure that the drain hose has no kinks or bends. Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to 'Care and cleaning'. Make sure that the connection of the drain hose is correct. Set the drain programme if you set a programme without drain phase. Set the drain programme if you set an option which ends with water in the tub. Set the spin programme. Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to 'Care and cleaning'. Adjust manually the items in the tub and start the spin phase again. This problem may be caused by balance problems. Make sure that the couplings of the water hoses are tight and there is not water leakages. Make sure that the drain hose have no damages. Make sure you use the correct detergent and the correct quantity of it. You cannot open the appliance door. • • Make sure that the washing programme is finished. Set the drain or the spin programme if there is water in the drum. The appliance makes an unusual noise. • Make sure the levelling of the appliance is correct. Refer to 'Installation'. Make sure that the packaging and/or the transit bolts are removed. Refer to 'Installation'. Add more laundry in the drum. The load may be too small. • • The washing results are not satisfactory. You cannot set an option. • • • • Increase the detergent quantity or use a different detergent. Use special products to remove the stubborn stains before you wash the laundry. Make sure that you set the correct temperature. Decrease the laundry load. • Make sure that you press only the wanted touch button(s). After the check, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact the Authorised Service Centre. If the display shows other alarm codes. Deactivate and activate the appliance. If the problem continues, contact the Service. 16 Service We recommend the use of original spare parts. When contacting the Authorised Service Centre, make sure that these data are available. You can find the information on the rating plate: model (Mod.), PNC (Prod.No.), Serial number (Ser.No.). www.zanussi.com Technical Data Dimension Width/ Height/ Depth/ Total depth 595 mm / 850 mm / 340 mm / 380 mm Electrical connection Voltage Overall power Fuse Frequency 230 V 2000 W 10 A 50 Hz Level of protection against ingress of solid particles and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture IPX4 Water supply pressure 0,5 bar (0,05 MPa) 8 bar (0,8 MPa) Minimum Maximum Cold water Water supply 1) Maximum Load Cotton 4 kg Spin Speed Maximum 1000 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. ENVIRONMENTAL CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. www.zanussi.com 17 * 18 www.zanussi.com www.zanussi.com 19 155248600-A-032014 www.zanussi.com/shop
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project