Dishlex DX103SK User Manual

User manual
Dishwasher
DX 103
Contents
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use of the appliance _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use of rinse aid _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Loading cutlery and dishes _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use of detergent _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Select and start a washing program _ _ _ _ _ _ _ _ _
2
3
4
4
5
5
7
7
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8
What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Water connection _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12
Electrical connection _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13
Warranty _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13
Subject to change without notice.
Safety instructions
For your safety and correct operation of the appliance, read this manual carefully before installation
and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know
the operation and safety features of the appliance.
Correct use
• Only use the appliance to clean household utensils
that are suitable for dishwashers.
• Do not put solvents in the appliance. Risk of explosion.
• Put the knives and all items with sharp points in the
cutlery basket with their points down. If not, put them
in a horizontal position in the upper basket.
• Use only products specified for dishwashers (detergent, salt, rinse aid).
• If you open the door while the appliance is in operation, hot steam can escape. Risk of skin burns.
• Do not remove dishes from the appliance before the
end of the washing program.
• When the washing program is completed, disconnect
the mains plug from the mains socket and close the
water tap.
• Only an authorised service engineer can repair this
appliance. Use only original spare parts.
• Do not do repairs yourself to prevent injury and damage to the appliance. Always contact the Customer
Care Centre.
General safety
• This appliance is intended to be used in household
and similar applications such as:
2
•
•
•
•
•
•
– Staff kitchen areas in shops, offices and other
working environments
– Farm houses
– By clients in hotels, motels and other residential
type environments
– Bed and breakfast type environments.
Some dishwasher detergents are strongly alkaline.
They can be extremely dangerous if swallowed.
Avoid contact with skin and eyes. Keep the children
away from the appliance when the door is open.
Check that the detergent dispenser is empty after
completion of the washing programme.
Obey the safety instructions from the manufacturer of
the dishwasher detergent to prevent burns to eyes,
mouth and throat.
Only put detergent in the dispenser before you start a
washing program.
Do not drink the water from the appliance. Detergent
residue can stay in your appliance.
Always close the door when you do not use the appliance to prevent injury and not to stumble over the
open door.
Do not sit or stand on the open door.
Child safety
• Do not let persons, children included, with reduced
physical sensory, reduced mental functions or lack of
experience and knowledge use the appliance. They
must have supervision or instruction for the operation
of the appliance by a person who is responsible for
their safety.
• Children should be supervised to ensure that they do
not play with the appliance.
• Keep all the packaging away from children. There is
a risk of suffocation.
• Keep all detergents in a safe area. Do not let children
touch the detergents.
• Keep children and pets away from the appliance
when the door is open.
Installation
• Make sure that the appliance is not damaged because of transport. Do not connect a damaged appliance. If necessary, contact the supplier.
• Remove all packaging before first use.
• A qualified and competent person must do the electrical installation.
• A qualified and competent person must do the
plumbing installation.
• Do not change the specifications or modify this product. Risk of injury and damage to the appliance.
• Do not use the appliance:
– if the mains cable or the water hoses are damaged,
– if the control panel, worktop or plinth area are
damaged so that you can get access to the inner
side of the appliance.
Contact your local Customer Care Centre.
• Do not drill into the sides of the appliance otherwise
damage to hydraulic and electrical components may
occur.
Warning! Carefully obey the instructions for
electrical and water connections.
Control panel
1 Program knob
2 Start/cancel button
3 Indicator light 'Finished'
4 On/off indicator light
5 Program marker
Indicator lights
Finished
Comes on when the washing program is completed. It also has the
auxiliary functions of alarm if the appliance has a malfunction.
Program knob and on/off indicator light
• To set a washing program, turn the program knob
clockwise or anticlockwise. The program marker on
the program knob must agree with one of the washing program on the control panel.
– The on/off indicator light comes on (position ON).
• To set the appliance to the off position, turn the program knob until the program marker agrees with the
on/off indicator light.
– The on/off indicator light goes off (position OFF).
3
Washing programmes
Program
Degree of soil
Type of load
Program description
Pots
Heavy soil
Crockery, cutlery, pots
and pans
Prewash
Main wash up to 70°C
2 intermediate rinses
Final rinse
Drying
Regular Plus
Normal soil
Crockery and cutlery
Prewash
Main wash up to 65°C
2 intermediate rinses
Final rinse
Drying
Quick 30 1)
Normal or light soil
Crockery and cutlery
(Partial load)
Main wash up to 65°C
Final rinse
Regular Eco 2)
Normal soil
Crockery and cutlery
Prewash
Main wash up to 50°C
1 intermediate rinse
Final rinse
Drying
Rinse & Hold
Any
Partial load (to be
completed later in the
day).
1 cold rinse (to prevent food
scraps to bond).
Detergent is not necessary with
this program.
1) This is the perfect daily program to clean a partial load. Ideal for a family of 4 persons who only want to load breakfast and dinner
crockery and cutlery.
2) Test program for test institutes. Please refer to separate leaflet supplied, for test data.
Consumption values
Program
Duration (in minutes)
Energy (in kWh)
Water (in litres)
Pots
85 - 95
1,7 - 1,9
20 - 22
Regular Plus
100 - 115
1,5 - 1,7
18 - 20
Quick 30
30
0,9
9
Regular Eco
90 - 100
0,83 - 0,91
16 - 18
Rinse & Hold
12
0,1
5
The pressure and temperature of the water, the
variations of power supply and the quantity of
dishes can change these values.
Use of the appliance
Refer to specified instructions for each step of the procedure.
4
1.
2.
Fill the rinse aid dispenser with rinse aid.
Load cutlery and dishes into the appliance.
3.
4.
Set the correct washing program for the type of
load and soil.
Fill the detergent dispenser with the correct quantity of detergent.
5.
Start the washing program.
Use of rinse aid
Caution! Only use rinse aid specified for
dishwashers.
Fill when the rinse aid indicator (B) becomes
clear.
Follow these steps to fill the rinse aid dispenser:
5
1
2
Caution! Do not fill the rinse aid dispenser with
other products (e.g. dishwasher cleaning agent,
liquid detergent). There can cause damage to the
appliance.
Adjusting the rinse aid dosage
The rinse aid is set at the
factory at position 4.
To increase or decrease
the dosage refer to 'What
to do if...'
3
4
Wash hands to remove any residue of rinse aid
from skin.
Loading cutlery and dishes
Helpful hints and tips
Only use the appliance for household utensils that are
suitable for dishwashers.
Do not use the appliance to clean objects that can absorb water (e.g. sponges, household cloths).
• Before you load cutlery and dishes, follow these
steps:
– Remove all food remainings and debris.
– Make burnt, remaining food in pans soft.
• While you load cutlery and dishes, follow these steps:
– Load hollow items (e.g. cups, glasses and pans)
with the opening down.
– Make sure that water does not collect in the container or in a deep base.
– Make sure that cutlery and dishes do not lie inside
one another.
– Make sure that cutlery and dishes do not cover
other cutlery and dishes.
– Make sure that glasses do not touch other
glasses.
5
– Put small objects in the cutlery basket.
• Plastic items and pans with non-stick coatings can
retain water droplets. Plastic items do not dry as well
as porcelain and steel items.
• Put light items in the upper basket. Make sure that
the items do not move.
Caution! Make sure that the spray arms can
move freely before you start a washing program.
Warning! Always close the door after you load or
unload the appliance. An open door can be
dangerous.
1
Arrange the items to let
water touch all surfaces.
2
For longer items, fold the
cup racks up.
Prevent to put plates in the first three sectors in
the front part of the basket. Make sure the plates
tilt forward.
Adjustment of the height of the upper basket
If you put large plates in the lower basket, first move the
upper basket to a upper position.
1
Arrange service dishes
and large lids around the
edge of the lower basket.
1
2
Maximum height of the dishes in :
upper basket
lower basket
Upper position
20 cm
31 cm
Lower position
24 cm
27 cm
2
Use the cutlery grid for best washing results. If the dimensions of the cutlery prevent use of the cutlery grid,
remove it.
6
Warning! Adjust the height before you load the
upper basket.
1
2
Follow these steps to move the upper basket to the upper or lower position:
1. Move the front runner stops (A) out.
2. Pull the basket out.
3. Put the basket in the upper or lower position.
4. Replace the front runner stops (A) in their initial position.
Caution! If the basket is in the upper position, do
not put cups on the cup racks.
Use of detergent
Only use detergents (powder, liquid or tablet) that
are suitable for dishwashers.
Follow the data on the packaging:
• dosage recommended by the manufacturer,
• storage recommendations.
Do not use more than the correct quantity of detergent to decrease pollution.
5
6
Different brands of detergent dissolve in different
times. Some detergent tablets do not have the
best cleaning results during short washing programs.
Use long washing programs when you use detergent
tablets to fully remove the detergent.
1
3
Fill the detergent dispenser (A) with detergent.
2
4
If you use a washing program with prewash
phase, put more detergent in the prewash detergent compartment (B).
Use of combi detergent tablets
These products are detergents with a combined cleaning and rinsing functions. They can contain also other
cleaning agents.
Refer to the instructions from the manufacturer for the
use of these products.
With tablets that contain rinse aid:
• set the lowest position for the rinse aid dosage,
• do not put rinse aid in the rinse aid dispenser. In this
condition rinse aid indicator light is always on when
you switch on the appliance.
.
Do these steps if the drying results are not satisfactory:
1. Fill the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
If you go back to use normal detergents again, fill
the rinse aid dispenser and adjust the rinse aid
dosage.
Select and start a washing program
Do these steps to set and start a washing program:
1. Close the door.
2. Turn the program knob to set the washing program. Refer to the chapter 'Washing programs'.
3.
– The on/off indicator light comes on.
Press the start/cancel button.
– The washing program starts automatically.
– The start/cancel indicator light comes on.
7
When the washing program operates, you cannot
change the program. Cancel the washing program.
Warning! Only interrupt or cancel a washing
program if necessary. Open the door carefully. Hot
steam and water can escape.
Cancelling a washing program
• Press and hold the start/cancel button until the start/
cancel indicator light goes off.
The washing program is cancelled.
At this time you can do these steps:
1. Switch off the appliance.
2. Set a new washing program.
Fill the detergent dispenser with detergent before you
set a new washing program.
Interrupting a washing program
1. Open the appliance door. The washing program
stops.
2. Close the appliance door. The washing program
continues from the point of interruption.
End of the washing program
• The appliance stops automatically.
• The 'Finished' indicator light comes on.
1. Switch off the appliance.
2. Open the door.
3. For better drying results, keep the door ajar for
some minutes before you remove the dishes.
If you do not switch off the appliance within 3 minutes, only the on/off indicator stays on. This
helps to decrease energy consumption.
Let the dishes cool down before you remove them from
the appliance. Hot dishes are easily damaged.
Removing the load
• First remove items from the lower basket, then from
the upper basket.
• There can be water on the sides and door of the appliance. Stainless steel becomes cool more quickly
than the dishes.
Care and cleaning
Warning! Switch the appliance off before you
clean it.
Cleaning the filters
Important! Do not use the appliance without the filters.
Make sure that the installation of the filters is correct.
Incorrect installation will cause unsatisfactory washing
results and damage to the appliance.
3
4
To remove filters B and
Remove the flat filter A
C, turn the handle apfrom the bottom of the approximately 1/4 anticlock- pliance.
wise.
1
8
2
Fully clean the filters A, B
and C below running water.
Long periods of non-operation
Do these steps when you do not use the appliance for a
long period:
1. Disconnect the mains plug from the mains socket.
2. Close the water tap.
3. Keep the door open to prevent unpleasant smells.
4. Keep the inner side of the appliance clean.
5
Put the filter A in the bottom of the appliance. Install the flat filter correctly
under the two guides D.
6
Put the filter system in position. To lock the filter
system, turn the handle
clockwise until it locks in
position
Important! Do not remove the spray arms.
If the holes in the spray arms become clogged, remove
remaining parts of soil with a cocktail stick.
External cleaning
Clean the external surfaces of the appliance and control
panel with a damp soft cloth. Only use neutral detergents. Do not use abrasive products, scouring pads or
solvents (acetone etc.).
Frost precautions
Caution! Do not install the appliance where the
temperature is below 0 °C. The manufacturer is
not responsible for damage because of frost.
If not possible, empty the appliance and close the door.
Disconnect the water inlet hose and remove water from
the water inlet hose.
Moving the machine
Do these steps to move the appliance:
1. Disconnect the mains plug from the mains socket.
2. Close the water tap.
3. Remove the appliance and the hoses.
4. Do not tilt the appliance during transport.
Internal cleaning
Do an inspection at intervals of 3 months. Set a washing
program for heavily soiled dishes. Use detergent, but do
not put dishes in the appliance.
What to do if…
The appliance does not start or stops during operation.
If there is a fault, first try to find a solution to the problem
yourself. Refer to following charts. If you cannot find a
solution to the problem yourself, contact your dealer or
the Customer Care Centre.
Warning! Switch the appliance off before you do
the suggested corrective actions.
9
Fault code and malfunction
Possible cause and solution
• continuous flash of the start/cancel indicator light
• 1 flash of the 'Finished' indicator light
The appliance does not fill with water
• The water tap is blocked or furred with limescale.
Clean the water tap.
• The water tap is closed.
Open the water tap.
• The filter in the water inlet hose is blocked.
Clean the filter.
• The connection of the water inlet hose is not correct. The hose can
be kinked or squashed.
Make sure that the connection is correct.
• continuous flash of the start/cancel indicator light
• 2 flashes of the 'Finished' indicator
light
The appliance will not drain
• There is a blockage in the sink spigot.
Clean the sink spigot.
• The connection of the water drain hose is not correct. The hose can
be kinked or squashed.
Make sure that the connection is correct.
The program does not start
• The appliance door is not closed.
Close the door.
• Mains plug is not connected.
Plug-in appliance to the mains.
• The fuse has blown out in the household fuse box.
Replace the fuse.
After the check, switch on the appliance. The program
continues from the point of interruption. If the malfunction shows again, contact your Customer Care Centre.
For other fault codes, not described in the chart, contact
your Customer Care Centre.
These data are necessary to help you quickly and correctly:
• Model (Mod.)
• Product number (PNC)
• Serial number (S.N.)
For these data, refer to the rating plate.
Write the necessary data here:
Model description : ..........
Product number : ..........
Serial number : ..........
The cleaning results are not satisfactory
The dishes are not clean
• The selected washing program is not applicable for the type of load and
soil.
• The baskets are loaded incorrectly so that water cannot reach all surfaces.
• Spray arms do not turn freely because of incorrect arrangement of the load.
• The filters are dirty or not correctly installed.
• The quantity of detergent is too little or missing.
The dishes are wet and dull
• No rinse aid has been used.
• The rinse aid dispenser is empty.
10
The cleaning results are not satisfactory
There are streaks, milky spots or
a bluish coating on glasses and
dishes
• Decrease the rinse aid dosage.
Dry water drop stains on glasses
and dishes
• Increase rinse aid dosage.
• The detergent can be the cause.
Technical data
Dimensions
Width (mm)
596
Height (mm)
850
Depth (mm)
610
Electrical connection - Voltage Overall power - Fuse
Information on the electrical connection is given on the rating plate on the
inner edge of the dishwasher door.
Water supply pressure
Minimum
50 kPa (7 psi)
Maximum
800 kPa (116 psi)
Capacity
Place settings
12
Environment concerns
The packaging materials are environmentally friendly
and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Discard the
packaging materials in the applicable container at the
community waste disposal facilities.
Warning! To discard the appliance, follow the
procedure:
• Pull the mains plug out of the socket.
• Cut off the mains cable and mains plug and discard
them.
• Discard the door catch. This prevents children closing themselves inside the appliance and endangering
their lives.
Old appliance
Make sure that the appliance goes to the applicable collection point for recycling.
Make sure that this appliance is discarded correctly. Inappropriate waste discard of the appliance causes negative consequences for the environment and human
health.
For more information about the recycling of this appliance, contact your local city office, your household
waste disposal service or the shop where you purchased the appliance.
Installation
Fitting under a counter
Warning! Make sure that mains plug is
disconnected from the mains socket during
installation.
Put the appliance adjacent to a water tap and a water
drain.
The plinth on freestanding appliance is not adjustable.
Do not remove the appliance worktop if you want to use
the dishwasher as a freestanding appliance.
Remove the appliance worktop to install it under a sink
unit or a kitchen counter.
Make sure that the dimensions of the recess agree with
the given dimensions.
11
the door does not catch on the sides of the cabinet. If
the door does not close correctly, loosen or tighten the
adjustable feet until the appliance is level.
Adhesive steam protection foil
If the worktop is removed, fit the steam protection on the
front part of the kitchen counter along the entire width.
1
3
2
4
The steam protection foil is not supplied with freestanding models, but can be purchased from Electrolux Spare Parts.
Adjusting the level of the appliance
Make sure that the appliance is level to close and seal
the door correctly. If the level of the appliance is correct,
Water connection
Water inlet hose
Connect the inlet hose to a water tap with an external
BSP thread spout of 3/4”.
For best washing performance it is recommended to
connect the appliance to a cold water supply.
Energy savings can be made by connecting the appliance to a Solar water system and using economy options, however the water temperature must not exceed
60 °C.
Inlet water supply
• Water pressure: 800 kPa max - 50 kPa min.
• Water flow rate 10 L / minute min.
• If water pressure is in excess of 800 kPa, a pressure
reducing valve should be used. Check for leaks.
• If water temperature is in excess of 60 °C, a tempering valve should be used. Check for leaks.
Caution! Always use new hoses when you
connect the appliance to the water mains. Old
hoses must not be used. The water inlet hose must be
examined at an interval of twelve months for
deterioration and replaced if necessary.
12
The water pressure must be in the limits (refer to 'Technical data'). Make sure that the local water authority
gives you the average mains pressure in your area.
Make sure that there are no kinks in the water inlet hose
and that the water inlet hose is not squashed or entangled.
Fit the hose nut correctly to prevent water leaks.
Caution! Do not connect the appliance to new
pipes or pipes that have been not used for a long
time. Let the water run for some minutes, then connect
the inlet hose.
Water drain hose
The highest point of the drain hose must be no more
than 60 cm from the floor and must have a continuous
fall.
The drain hose can be lengthened using additional
lengths and connectors. These must be purchased from
Electrolux Spare Parts. The extension length must not
exceed 2 metres.
The drain hose must be free of obstructions.
Remove the sink plug when the appliance drains the
water to prevent that the water goes back into the appliance.
If you connect the water drain hose to a trap spigot under the sink, remove the plastic membrane. If you do not
remove the membrane, remaining food can cause a
blockage in the drain hose spigot.
The appliance has a security feature to prevent dirty water going back into the appliance. If, the spigot of the
sink has a 'non-return valve', this valve can cause the
appliance to drain incorrectly. Remove the non-return
valve.
Make sure that the water couplings are tight to prevent
water leakage.
Caution! Ensure that the hoses are not bent or
squashed under or behind the appliance.
Caution! Once connected the inlet hose to the
water tap, turn the tap on and check that there are
no leaks.
Electrical connection
Warning! Safety standards require the appliance
to be earthed.
Prior to using the appliance for the first time, ensure that
the rated voltage and type of supply on the rating plate
match that of the supply where the appliance is to be
installed.
The fuse rating is also to be found on the rating plate.
Always plug the mains plug onto a correctly installed
approved socket.
Do not use multi-ways plugs, connectors and extension
cables. This can constitute a fire hazard through
overheating.
If necessary, have the domestic wiring system socket
replaced. If the mains cable has to be replaced, contact
your local Customer Care centre.
The mains plug must be accessible after the appliance
has been installed.
Never unplug the appliance by pulling on the cable.
Always pull the plug.
Test the appliance. Run a quick washing program and
ensure that the appliance fills with water, washes and
drains with no leaks.
The manufacturer accepts no liability for failure to
observe the above safety precautions.
Warranty
FOR SALES IN AUSTRALIA AND NEW ZEALAND
APPLIANCE: DISHWASHER
This document sets out the terms and conditions of
the product warranties for Electrolux Appliances. It
is an important document. Please keep it with your
proof of purchase documents in a safe place for future reference should you require service for your
Appliance.
1. In this warranty
a) ‘acceptable quality’ as referred to in clause 10
of this warranty has the same meaning referred to in the ACL;
b) ‘ACL’ means Trade Practices Amendment
(Australian Consumer Law) Act (No.2) 2010;
c) ‘Appliance’ means any Electrolux product purchased by you accompanied by this document;
d) ‘ASC’ means Electrolux’ authorised serviced
centres;
13
2.
3.
4.
5.
14
e) ‘Electrolux’ means Electrolux Home Products
Pty Ltd of 163 O’Riordan Street, Mascot, NSW
2020, ABN 51 004 762 341 in respect of Appliances purchased in Australia and Electrolux
(NZ) Limited of 3-5 Niall Burgess Road, Mount
Wellington, in respect of Appliances purchased in New Zealand;
f) ‘major failure’ as referred to in clause 10 of this
warranty has the same meaning referred to in
the ACL and includes a situation when an Appliance cannot be repaired or it is uneconomic
for Electrolux, at its discretion, to repair an Appliance during the Warranty Period;
g) ‘Warranty Period’ means:
– where the Appliance is used for personal,
domestic or household use (i.e. normal single family use) as set out in the instruction
manual, the Appliance is warranted against
manufacturing defects in Australia for 24
months and in New Zealand for 24 months,
following the date of original purchase of
the Appliance;
– this Appliance is not designed for commercial use and therefore no warranty applies
in this case;
h) ‘you’ means the purchaser of the Appliance
not having purchased the Appliance for resale, and ‘your’ has a corresponding meaning.
This warranty only applies to Appliances purchased and used in Australia or New Zealand and
is in addition to (and does not exclude, restrict, or
modify in any way) any non-excludable statutory
warranties in Australia or New Zealand.
During the Warranty Period Electrolux or its ASC
will, at no extra charge if your Appliance is readily
accessible for service, without special equipment
and subject to these terms and conditions, repair
or replace any parts which it considers to be defective. Electrolux or its ASC may use remanufactured
parts to repair your Appliance. You agree that any
replaced Appliances or parts become the property
of Electrolux. This warranty does not apply to light
globes, batteries, filters or similar perishable parts.
Parts and Appliances not supplied by Electrolux
are not covered by this warranty.
You will bear the cost of transportation, travel and
delivery of the Appliance to and from Electrolux or
6.
7.
8.
9.
its ASC. If you reside outside of the service area,
you will bear the cost of:
a) travel of an authorised representative;
b) transportation and delivery of the Appliance to
and from Electrolux or its ASC,
In all instances, unless the Appliance is transported by Electrolux or an Electrolux authorised representative, the Appliance is transported at the owner’s cost and risk while in transit to and from Electrolux or its ASC.
Proof of purchase is required before you can make
a claim under this warranty.
You may not make a claim under this warranty unless the defect claimed is due to faulty or defective
parts or workmanship. Electrolux is not liable in the
following situations (which are not exhaustive):
a) the Appliance is damaged by:
– accident
– misuse or abuse, including failure to properly maintain or service
– normal wear and tear
– power surges, electrical storm damage or
incorrect power supply
– incomplete or improper installation
– incorrect, improper or inappropriate operation
– insect or vermin infestation
– failure to comply with any additional instructions supplied with the Appliance;
b) the Appliance is modified without authority
from Electrolux in writing;
c) the Appliance’s serial number or warranty seal
has been removed or defaced;
d) the Appliance was serviced or repaired by
anyone other than Electrolux, an authorised
repairer or ASC.
This warranty, the contract to which it relates and
the relationship between you and Electrolux are
governed by the law applicable where the Appliance was purchased. Where the Appliance was
purchased in New Zealand for business purposes
the Consumer Guarantee Act does not apply.
To the extent permitted by law, Electrolux excludes
all warranties and liabilities (other than as contained in this document) including liability for any
loss or damage whether direct or indirect arising
from your purchase, use or non use of the Appliance.
10. For Appliances and services provided by Electrolux
in Australia, the Appliances come with a guarantee
by Electrolux that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have
the Appliance repaired or replaced if the Appliance
fails to be of acceptable quality and the failure
does not amount to a major failure. The benefits to
you given by this warranty are in addition to your
other rights and remedies under a law in relation to
the Appliances or services to which the warranty
relates.
11. At all times during the Warranty Period, Electrolux
shall, at its discretion, determine whether repair,
replacement or refund will apply if an Appliance
has a valid warranty claim applicable to it.
12. For Appliances and services provided by Electrolux
in New Zealand, the Appliances come with a guarantee by Electrolux pursuant to the provisions of
the Consumer Guarantees Act, the Sale of Goods
Act and the Fair Trading Act.
13. To enquire about claiming under this warranty,
please follow these steps:
a) carefully check the operating instructions, user
manual and the terms of this warranty;
b) have the model and serial number of the Appliance available;
c) have the proof of purchase (eg an invoice)
available;
d) telephone the numbers shown below.
14. You accept that if you make a warranty claim,
Electrolux and its ASC may exchange information
in relation to you to enable Electrolux to meet its
obligations under this warranty.
Important Notice
Before calling for service, please ensure that the steps listed in point 13 above have been followed.
FOR SERVICE
or to find the address of your nearest state service centre in Australia
Please call 13 13 4 9
For the cost of a local call (Australia only)
SERVICE AUSTRALIA
ELECTROLUX HOME PRODUCTS
www.electrolux.com.au
FOR SPARE PARTS
or to find the address of your nearest state spare parts centre in Australia
Please call 13 13 50
For the cost of a local call (Australia only)
FOR SERVICE
SERVICE NEW ZEALAND
or to find the address of your nearest authorised service centre in New ELECTROLUX HOME PRODUCTS
Zealand
www.electrolux.co.nz
Free call 0800 10 66 10
FOR SPARE PARTS
or to find the address of your nearest state spare parts centre in New
Zealand
Free call 0800 10 66 20
(New Zealand only)
(New Zealand only)
15
www.electrolux.com/shop
156962051-A-132013