Electrolux EHT311X User Manual

325 88-7551 Rev. 2-425
INSTRUCTION BOOK
Model No.
Product No.
Serial No.
GB
EHT 311 X
949 600 840
AUS
NZL
From the Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more
than 150 countries around the world.
24
1
11 The Company (and any company
related to the Company) will not
be liable for any special
incidental or consequential
damages or for loss, damage or
expense directly or indirectly
arising from the use or inability
to use this appliance, or for
personal injury or loss or
destruction of other property.
12 Nothing in this warranty is
intended to limit the rights you
may have under the Consumer
Guarantees Act 1993, except to
the extent permitted by that Act,
and all provisions of this
warranty shall be read as
modified to the extent necessary
to give effect to that intention.
13 The Consumer Guarantees Act
1993 does not apply if your
appliance is acquired for the
purposes of a “business” (as
defined in that Act).
14 This warranty is limited to 90
days from date of purchase if the
appliance is used for commercial
use.
reasons detailed therein, a service
fee will be charged. Please present
proof of purchase to any Authorised
Service Centre should warranty
service be required.
SERVICE CENTRES
PLEASE PHONE
0800 10 66 10
For your nearest Authorised
Service Centre please look in
The Yellow Pages under
Home Appliance Servicing
or Call 0800 10 66 10
IMPORTANT NOTICE
Before calling a service technician
please carefully check the warranty
terms and conditions, the operating
instructions and service booklet if
applicable. If the product fails for
any of the customer responsibility
2
23
ELECTROLUX APPLIANCE WARRANTY –
NEW ZEALAND
This appliance is warranted by
Electrolux Home Products (NZ) Ltd
(“the Company”) from the date of
purchase. The following terms and
conditions apply:
person other than someone
authorised by the Company.
7 If you live outside the service area
of the Company or its Authorised
Service Centre, this warranty does
not cover the cost of transport of
the appliance for service nor the
Authorised Service Centre’s
travelling costs to and from your
home.
8 If you are required to transport the
appliance to the Company or its
Authorised Service Centre, it
must be securely packed and
insured.
The Company does not accept
any responsibility for loss or
damage
prior to it being received by the
Company or its Authorised
Service Centre.
9 This warranty is the only express
warranty given by the Company.
10 This Warranty does not cover
loss, damage or expense to this
appliance caused directly or
indirectly by power surges,
electrical storm damage or
incorrect power current.
1 The Company or its Authorised
Service Centre will pay the cost of
repairing or replacing all parts of
the appliance which the
Company or its Authorised
Service Centre find defective for a
period of 24 months following the
date of purchase (the “Warranty
Period”).
2 During the Warranty Period the
Company or its Authorised
Service Centre, will pay the cost
of repairing or replacing all
parts, which they find are
defective.
3 Light globes, batteries and filters
are replaceable parts and are not
covered under this warranty.
4 The appliance must be installed
and operated in accordance with
the Company’s instructions.
5 This Warranty does not apply to
normal wear and tear, or any
service, which is needed after an
accident, negli gence, alteration
or misuse.
6 This Warranty also does not apply
to damage caused if your
appliance has been dismantled,
repaired or serviced by any
22
Contents
Page no
Important to know ........................................................................................... 4
Overview .................................................................................................... 6
Operating .................................................................................................... 7
Ignition
.................................................................................................. 10
Maintenance And Cleaning ........................................................................... 11
Mounting .................................................................................................. 12
Technical data ............................................................................................... 18
Service
.................................................................................................. 19
Electrolux warranty Australien ..................................................................... 20
Electrolux appliance warranty - New Zealand ............................................. 22
It is important to know how the hob works, for which reason we would ask you to
read these instructions carefully before using it. Only then we can quarantee that
"your new kitchen aid" will fully meet your expectations and requirements that you
had when you chose your Electrolux system.
Sincerely
Electrolux
3
Important to know
Never leave the appliance unattended
while deep frying, or heating fats and
oils.
These warnings are provided in the
interests of your safety. Ensure you
fully understand them before installing
or using the appliance. Your safety is
of paramount importance. If you are
unsure about the meaning of these
warnings contact the Customer Care
Department for assistance.
Ensure pots are placed centrally over
the burner and do not overhang the
bench surface or control knobs.
Do not allow pots to boil dry.
Installing
Do not use or store flammable
materials near this appliance. Do not
spray aerosols in the vicinity of this
appliance while it is in operation.
Where this appliance is installed in
marine craft or caravans, it shall not be
ed as a space heater
This appliance must be installed
according to the instructions supplied.
Any installation work must be
undertaken by an authorised competent
person.
Do not alter the specifications or
attempt to modify the appliance in any
way.
The appliance is not intended for use
by young children or infirm
persons without supervision.
During Use
The appliance is intended for domestic
cooking only. It is not designed for
commercial/industrial purposes.
Child Safety
Young children should be supervised to
ensure that they do not play
with the appliance
Ensure that the control knob is in the
OFF position when not in use.
The appliance gets hot when it is in
use.
Children should be kept away until the
appliance has cooled.
Do not use the appliance if it is
damaged in any way, contact your local
Electrolux Service Centre.
Maintenance and Cleaning
Only clean this appliance in
accordance with the instructions given
in this book.
Never use plastic or aluminium dishes
on the appliance.
4
10 This warranty does not cover
loss, damage or expense to this
appliance caused directly or
indirectly by power surges,
electrical storm damage or
incorrect power current.
11 The Company (and any company
related to the Company) will not
be liable for any special,
incidental or consequential
damages or for loss, damage or
expense or for personal injury or
loss or destruction of property
arising directly or indirectly from
the use or inability to use this
appliance or any of its parts.
12 This warranty applies only to the
original buyer.
13 This warranty is the only express
warranty given by the Company.
14 If you are the original buyer,
please keep your proof of
purchase, which will be required,
if you request service under this
warranty.
15 The Warranty Period is only
applicable when your appliance
is used at home by you and your
family as consumers.
16 Use of this appliance for
commercial purposes is covered
by this warranty for a period of 3
months from the date of
purchase.
FOR SERVICE IN AUSTRALIA
PLEASE CALL 13 13 49
FOR SPARE PARTS IN AUSTRALIA
PLEASE CALL 13 13 50
21
ELECTROLUX WARRANTY AUSTRALIA
Nothing in this warranty, limits any
rights you may have under the
Trade Practices Act or any other
Commonwealth or State legislation.
Such rights cannot be changed by
the conditions in this warranty.
the Company’s instructions.
6 This warranty does not apply to
normal wear and tear, or any
service, which is needed after an
accident, alteration, negligence,
misuse, fire or flood.
7 This warranty does not apply to
damage caused if your appliance
has been dismantled, repaired or
serviced by any person other
than someone authorised by the
Company.
8 If you live outside the service area
of the Company or one of its
service agents, this warranty does
not cover the cost of transport of
the appliance for service nor the
service agent’s travelling costs to
and from your home.
9 If you are required to transport the
appliance to the Company or its
service agent, you must ensure it
is securely packed and insured.
The Company does not accept
any responsibility for loss or
damage of the appliance prior to it
being received by the Company
or its service agent.
Subject to the conditions below,
this appliance is warranted by
Electrolux Home Products Pty. Ltd.
A.B.N. 51 004 762 341, (the
“Company”), to be free from
defects in materials and
workmanship for a period of 24
months following the date of
purchase (the “Warranty Period”).
Conditions of the warranty:
1 During the Warranty Period the
Company, or its service agent,
will only pay the cost of repairing
or replacing all Company parts on
your appliance which the
Company finds to be defective.
2 The Company will decide if there
are any defects in material and/or
workmanship.
3 Light globes, batteries and filters
are replaceable parts and are not
covered under this warranty.
4 This warranty applies only for
mainland Australia and
Tasmania.
5 The appliance must be installed
and operated in accordance with
20
Service
Repairs carried out by
inexperienced persons may cause
injury or serious malfunction of the
appliance. Repairs must only be
carried out by an authorised person.
Contact your local Electrolux
Service Centre;
For service within Australia:
Please phone 131349 (Australia
only).
For service within New Zealand:
Please phone 0800 106 610 (Free
Call New Zealand Only).
Disposal
Make the gas hob unusable by
cutting off the cable
Dispose of any packaging material
and old appliances at an authorised
disposal sites.
5
Overview
Service
Burner
Sympton:
Solution:
There is no spark when lighting the
gas?
Check whether the 240 V connection
has been plugged in. The ground fault
circuit relay way have switched off.
The fuse has blown
When the operating knob is released
the gas ring goes out again?
The operating knob has not been
depressed long enough, or has not
been depressed sufficiently.
The gas ring burns very unevenly?
Ensure the cover has been replaced
correctly, e.g. after cleaning.
Any of the following are considered to
be abnormal operation and may
require servicing:
If service is required contact:
*
*
*
*
*
For service within Australia:
Please phone 131349 (Australia only).
B2115
Knob
Yellow tipping of burner flame
Sooting up of cooking utensils
Burners not igniting properly
Burners failing to remain alight
Burner/s extiguised by cupboard
doors.
* Gas valves which are difficult to
turn.
Placement of grid
Wrong
Electrolux Service Centre;
For service within New Zealand:
Please phone 0800 106 610 (Free Call
New Zealand Only).
Guide knob for grid
Right
6
19
Operations
Technical data
Type of gas
Adjusted for natural gas: 1,0 kPa
(test point pressure)
Radio-noise reduction
This unit observes the current EECdirective on radio noise reduction.
Panel markings
Q = Nominal gas consumption NG:
Wok burner:
13,0 MJ/h
Total:
13,0 MJ/h
Material:
Off.
AUS/NZL:
Convertible to universal LPG (Propane):
2,75 kPa (test point pressure).
Built-in measurements:
Height:
60 mm
Width:
270 mm
Depth:
490 mm
Stainless steel,
Pansupport: Castiron enamelled
Q = Nominal gas consumption universal
LPG:
Wok burner:
13,7 MJ/h
Total:
13,7 MJ/h
The operating knob has a ring showing
the scale of markings.
Max. flame
and ignition position
Min. flame
Product measurements:
Height:
Width:
Depth:
Hob is approved in accordance with
AS4551 (AG101) Australian Standard
Domestic Gas Cooking Appliances.
Weight:
55 mm
290 mm
510 mm
9 kg
„THIS APPLIANCE MUST BE
CONNECTED TO AN EARTHED
GENERAL PURPOSE OUTLET“.
Electrical supply 230/240 V 50 Hz AC,
0,1A max
Ignition=
240 V / 0,6 VA generator
FSD
The unit features fully-secured gas taps
(thermo-fuse)
18
7
Before leaving
Burner cover/burner ring
Together with the burner ring the burner
cover forms a space where the final
mixture of gas and air takes place in
order to make the gas burn correctly.
Burner ring
Burner cover
Correct
Please note: It is consequently very
important that the burner cover/ring is
placed correctly on the burner. The
burner ring has been provided with
holes for the ignition electrode, and the
thermo sensor.
Wrong
If the burner cover/ring are wrongly
placed the burner will operate
incorrectly, and the burners may be
damaged within at short space of time.
The pipe connections should be
checked for leaks with soap and
water. Do not use a naked flame
for detecting checks.
Test all burners on high and low
flame for flame stability. Test the
stability of the low flame when any
nearby cupboard doors are used.
When satisfied with the appliance,
please instruct the user on the
correct method of operation. If the
appliance fails to operate correctly
after all checks have been made,
refer to the authorised service
provider in your area.
The units externally
measured length
Ignition electrode (A)
The burner has been provided with an
ignition electrode. As long as the
operating knob is depressed, the
automatic ignition will ensure that a
spark is emitted between the ignition
electrode and the burner cover.
Burner
Burner ring
Main nozzle
Burner cap
Thermo Sensor (B)
The hob unit features fully-secured gas
taps (thermo-fuse)
In case the flame goes out, the thermo
sensor automatically prevents gas
admission after a few seconds (max. 90
seconds).
Note: Gas admission is always allowed
while the operation button is pressed See start-up procedure
Ignition electrode (A)
T hermo Sensor (B)
145 mm:
Cooker hood
290 mm:
Two-zone ceramic-top electric hob
Two-burner gas hob
Grill
Fryer
Wok
580 mm:
Four-zone ceramic-top electric hob
Four-burner gas hob.
725 mm:
Four-zone ceramic-top electric hob.
8
17
The wok-unit has a special pan support
which enables use of a wok pot with
curved bottom.
When using cooking utensils with a
flat bottom the diameter of the utensils
must not be less than 26 cm.
Electrical Connection
This appliance is supplied with an
1800mm long flexible supply lead and
3 pin plug. The point of connection is
located at the rear and on the
underside of the appliance. Connect
the appliance to a readily accessible
switched general purpose outlet which
is adjacent to the appliance.
THIS APPLIANCE MUST BE
CONNECTED TO AN EARTHED
GENERAL PURPOSE OUTLET.
16
9
Ignitions
1. Depress and turn the control knob
for the burner, the left to Max. flame
2. The ignition electrode will emit
sparks, and when the mixture of gas
and air is correct, the burner will be
ignited. Is not possible to connect
the unit to mains, a match may be
used to ignite the burner
3. After starting the burner, press the
control knob for approx. 10
seconds to activate the automatic
thermo couple.
4. Important Ignition position is at
Max flame
For Universal LPG the regulator is
fitted to the gas inlet of the
appliance so that a pressure test
point is available. The regulator
should be disabled by adjusting the
regulator adjusting screw to be fully
screwed in, but do not remove the
locking nut from the regulator. The
supply pressure to the appliance is
controlled by the regulator located
on the LPG cylinder. This cylinder
regulator should be adjusted to give
a pressure of 2.75kPa at the
appliance inlet with the large and
simmer burners operating at
maximum.
Typical Adjustment
for Natural Gas
Adjusted for LPG
B2004
Use of Hose Assemblies.
If the appliance is to be installed
using a hose assembly, then
1. The hose must be AGA certified
to AS/NZS 1869 as class B or
class D, and utilised in
accordance with requirements of
AS 5601 (AG 601).
2. The connection point between the
consumer piping and the hose
must be accessible with the
appliance installed.
10
15
Maintenance and cleaning
Fixing
Gas installation
* Prepare the cut out according to
the "cut out measurements”.
Connect the brass extension Piece to
the bras elbow on the underside of hob.
The appliance is factory set for
Natural Gas. Fit the gas regulator
supplied with the appliance to the gas
inlet. The location of the gas inlet is
approximately 240mm form the right
hand side of the appliance and
40mm from the back of the appliance.
The connection of the Gas Regulator
is ½” Gas female thread and the
pressure at the test point should be
adjusted to1.00kPa with the large and
simmer burners operating at
maximum.
For Universal LPG connection, the
appliance needs to be first converted
using the conversion kit and
instructions supplied with the
appliance.
* Screw the fixing brackets out to such
an extent that they can be turned in
under the table top.
Tighten the brackets on the to table
top with an ordinary screwdriver.
14
The operating panel with knob pan
support top plate and burner
covers/rings are to be cleaned with
ordinary cleaning agents.
However, do not use any kind of
scouring powder.
The hob with the stainless steel top
plate is to be washed with ordinary
soap and water. Dry thoroughly to
avoid lime stains. Any such stains may
be removed with vinegar or whiting
dissolved in spirit.
Avoid saucepans boiling over. If you
have been so unfortunate as to get
water in the burner this water should
be removed before re-igniting the
burner, e.g. with a no-fluff cloth.
11
Mounting
This appliance must be installed by an
authorised person.
This appliance shall be installed in
accordance with the manufacturer's
installation instructions, local gas fitting
regulations, municipal building codes,
AS5601 (AG601) Australian Standard Gas Installations and any other relevant
statutory regulations.
Data label
The data label is located on the
underside of the hob next to the gas
connection. A duplicate data label is
supplied to adhere in an accessible area
next to the hob. This appliance is
suitable for Natural Gas and Universal
LPG, ensure that the available gas
supply matches the data label.
Any adjoining wall surface situated
within 200 mm from the edge of
any hob burner must be a suitable
noncombustible material for a
height of 150 mm for the entire
length of the hotplate.
Any combustible construction
above the hotplate must be at least
600 mm above the top of the burner
and no construction shall be within
450 mm above the top of burner. A
minimum depth of 60 mm from the
top of the worktop surface must be
provided for the hotplate.
Cut-out measurements
Ventilation
Ventilation must be in accordance with
AS5601 (AG601) Gas installations. In
general, the appliance should have
adequate ventilation for complete
combustion of gas, proper flueing and to
maintain temperature of immediate
surroundings within safe limits.
reinforcement beam to the table
surface, as it is held in place by a
specially designed moulding, which
is incorporated in the hob units
flanges.
One rectangular hole is sawn out for
the hob combination chosen.
The depth of the cut-out for any unit
is: 490 mm length of hole = sum of
all units` externally measured
length, less 20 mm. If the appliance
is to be installed as a single unit
then the length of the hole shoul be
the length of the unit less 18 mm.
Minimum
distance
to side wall:
150 mm
Reinforcement
beams
Mounting of Reinforcement
Beams
A reinforcement Beam, with
supporting flanges at each end, is
included with each two-burner unit.
For unit combinations, a
reinforcement beam must be used
between each unit.
It is not necessary to attach the
Location
Choose a location free of draughts and
open doors and clear of combustible
materials or other fire hazards. The
location should ensure convenience of
operation and service.
12
13
Minimum distance
to back wall (nonflammable material):
50 mm
">