Tricity Bendix SG210/1W User Manual

Operating &
Installation
Instructions
Gas
Cooker
SG210/1W
CONTENTS
Instructions for the User
Instructions for the Installer
Important Safety Information
3
Technical Features
17
Description of the appliance
5
Using the appliance
- Using the oven
- Hints & Tips
- Using the Grill
- Cooking Chart
- Using the Hob
6
6
8
9
11
12
Safety Advice
- Gas connections
18
18
Electrical connections
18
Maintenance and Cleaning
14
Installation
- Location
- Ventilation
- Levelling
20
20
20
21
Something Not Working
15
Gas connections
21
Service & Spare Parts
28
Conversion of gas
23
Customer Care
28
Guarantee Conditions
29
How to read the instruction book
The symbols below will guide you when reading the instruction book
Safety instructions
Step by Step Operation
Advice and recommendations
Environmental Information
2
IMPORTANT SAFETY INFORMATION
You MUST read these warnings
carefully before installing or using the
appliance. If you need assistance, contact
our Customer Care Department on 08705
950950
Installation
• This cooker must be installed by
qualified personnel, according to the
manufacturer’s instructions and to the
relevant British Standards.
• This cooker is heavy. Take care when
moving it.
• Any gas installation must be carried
out by a registered competent
installer.
• Any electrical installation must be
carried out by a qualified
electrician/competent person.
• Remove all packaging before using the
cooker.
• This cooker must not be connected to a
combustion products evacuation
device. It shall be installed and
connected in accordance with current
installation regulations. Particular
attention shall be given to the relevant
requirements regarding ventilation.
• This cooker is designed to be
connected to a 230-240V, 50Hz
electrical supply.
• Ensure that the gas and electrical
supply complies with the type stated
on the rating plate, located on the
lower left corner of the front of the
cavity.
• Do not attempt to modify the cooker in any
way.
Child Safety
• This cooker is designed to be operated
by adults. Do not allow children to play
near or with the cooker.
• The cooker gets hot when it is in use.
Children should be kept away until it has
cooled.
• Children can also injure themselves by
pulling pans or pots off the cooker.
During Use
• This cooker is intended for domestic
cooking only. It is not designed for
commercial or industrial purposes.
• When in use a gas cooker will
produce heat and moisture in the
room in which it has been installed.
Ensure there is a continuous air
supply, by keeping air vents in good
condition or installing a cooker hood
with a venting hose.
• When using the cooker for a long
period of time, opening a window or
increasing the extractor speed should
improve the ventilation.
• Do not use this cooker if it is in contact
with water. Do not operate the cooker
with wet hands.
• The grill pan will become hot during
use, always use oven gloves when
removing or replacing a hot grill pan.
3
• Ensure the control knobs are in the
‘OFF’ position when not in use.
• When using other electrical appliances,
ensure the cable does not come into
contact with the hot surfaces of the
cooker.
• Unstable or misshapen pans should not
be used on the hob burners as unstable
pans can cause an accident by tipping or
spillage.
• Never leave the cooker unattended
when cooking with oil and fat.
• Never pull the appliance by the oven
handle.
• This cooker should be kept clean at all
times. A build-up of fat or foodstuff could
result in a fire.
• Never use steam or high-pressure
appliances for cleaning the oven.
• Never use plastic dishes in the oven or
on the hob burners. Never line any part
of the oven with aluminum foil.
• Always ensure that the oven vent, which
is located at the centre back of the hob,
is left unobstructed to ensure ventilation
of the oven cavity.
• Perishable food, plastic items and
aerosols may be affected by heat and
should not be stored above the cooker.
Service
This cooker should only be repaired or
serviced by an authorized Service Engineer
and only genuine approved spare parts
should be used.
4
•
•
Environmental Information
After installation, please dispose of the
packaging with due regard to safety
and the environment.
When disposing of an old appliance,
make it unusable, by cutting off the
cable.
on the product or on its
The symbol
packaging indicates that this product may
not be treated as household waste. Instead it
should be taken to the appropiate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local city office,
your household waste disposal service or
the shop where you purchased the product.
Keep this instruction book for future
reference and ensure it is passed on to
any new owner.
DESCRIPTION OF THE APPLIANCE
Hob
2000W
1000W
Control panel
Door handle
2
3
1
4
Oven door
2000W
1.
2.
3.
4.
Adjustable
small feet
2600W
Front left burner (semi-rapid)
Back left burner (semi-rapid)
Back right burner (auxiliary)
Front right burner (rapid)
Control panel
1
1.
2.
3.
2
Ignition switch
Oven/grill knob
Front left burner control knob
3
4
5
6
4. Back left burner control knob
5. Back right burner control knob
6. Front right burner control knob
5
USING THE APPLIANCE
Before the First Use of the Cooker
Remove all packaging both inside
and outside of the cooker, before
using it.
Before first use, the oven should be heated
without food. During this time, an unpleasant
odour may be emitted. This is quite normal.
1.
2.
3.
4.
Remove the oven accessories and
ensure all packaging has been
removed.
Ignite the oven burner (see instructions)
and turn the control knob to 8
(maximum).
Open a window for ventilation
Allow the oven to run empty for
approximately 45 minutes.
This procedure should be repeated with the
grill function for approximately 5-10 minutes.
Using the Oven
The cooker gets hot when it is in
use. Children should be kept away
until it has cooled.
Stand clear when opening the
drop down oven door.
Do not allow it to fall open support the door using the door
handle, until it is fully open.
Attention: when turning on the
oven and grill burner the oven
door has to be opened.
The oven has three shelf levels, and is
supplied with one shelf.
The shelf positions are counted from the
bottom of the oven as shown in the diagram.
6
3
Shelf
levels
2
1
Do not place cookware or foil
directly on the oven base.
Oven Safety device
The cooker features a thermocouple; if for
any reason the flame should extinguish, the
device will stop the gas flow.
Use
The oven can be used for traditional
cooking, or for grilling, but not both functions
simultaneously.
The symbol on the knob corresponds to
the symbol on the control panel.
Off
“8”
“1”
Maximum
Minimum
If for any reason the flame should extinguish
turn control knob to the off position, after at
least 1 minute, try to re-ignite the oven.
Grill function (heat comes from the top
burner only.
Ignition
Attention: when turning on the
oven and grill burner the oven
door has to be opened.
•
•
•
Open the oven door and lift the small
lid on the bottom of the cavity, push
and turn the control knob to the left to
position 8, keeping the control knob
pressed.
At the same time, push the electronic
ignition knob (see fig). Keep it pushed
until the gas ignites (1 spark / second).
Release the knob after 10 seconds
and check that the burner is ignited
through the holes in the burner
cover.
Cooking in the Oven
Traditional cooking is made by natural
convection; the heated air circulates on the
principle of ascending and descending
draughts. It is necessary to pre-heat the
oven.
All cookers vary and it is important to be
aware of the approximate cooking
temperatures before you use the cooker.
It may be necessary to adjust the
temperature to suit your individual
requirements. Only experience will enable
you to determine the correct setting for your
personal requirements.
OR
Power Cut
• Open the oven door and lift the small
lid on the bottom of the cavity, push and
turn the control knob to the left to
position 8, keeping the control knob
pressed.
• Release the knob after 10 seconds
and check that the burner is ignited
through the holes in the burner cover.
7
Hints and Tips
Condensation and steam
When food is heated it produces steam in
the same way as a boiling kettle. The oven
vents allow some of this steam to escape.
However, always stand back from the
oven when opening the oven door to
allow any build up of steam or heat to
release.
If the steam comes into contact with a cool
surface on the outside of the oven, e.g. a
trim, it will condense and produce water
droplets. This is quite normal and is not a
fault with the oven.
To prevent discolouration, regularly wipe
away condensation and also soilage from
surfaces.
Cookware
Use any ovenproof cookware, which will
withstand temperatures of 250°C.
Oven dishes, etc. should not be placed
directly on the oven base.
Oven Cooking
• Turn off the oven 5 minutes before the
end of cooking time, and use residual
heat to complete the cooking.
• The thickness, the material and the colour
of the pan will influence the cooking
results.
• When cooking, certain dishes increase
in volume, ensure the pan is large
enough.
• To prevent fat dripping when roasting
use tall rim pans proportional to the item
being roasted.
• Prick the skin of poultry and sausages
with a fork before cooking to avoid
spitting.
• Use heatproof glass dishes for soufflés.
8
The effects of dishes on cooking
results
Dishes and tins vary in their thickness,
conductivity, colour, etc. which affects the
way they transmit heat to the food inside
them.
A
Aluminum, earthenware, oven
glassware and bright shiny utensils reduce
cooking and base browning.
B
Enameled cast iron, anodized
aluminum, aluminum with non-stick interior
and colour exterior and dark, heavy
utensils increase cooking and base
browning.
Using the Grill
When using the grill it has to be
supervised, the oven door opened and
the grill deflector “A” in place.
Heat comes from the top of the oven. It is
suitable for grilling meat (steak, bacon etc…)
that remains tender, for toast or to brown
food already cooked.
A
Grill burner ignition
Attention: when turning on the
oven and grill burner the oven door has
to be opened.
• Open the oven door push and turn the
control knob to the right to the “grill
symbol” and keep the control knob
pressed.
• At the same time, push the electronic
ignition knob (see fig). Keep it pushed
until the gas ignites (1 spark / second).
• Upon ignition, keep the knob
pressed for approximately 10
seconds (until the safety valve
automatically keeps the grill burner
lit).
OR
Power Cut
• Open the oven door.
• Hold a flame to the gas grill burner holes
(see fig.).
• Press the oven/grill function control
knob, then turn it to the “grill symbol”.
Upon ignition, keep the knob pressed
for approximately 10 seconds (until
the safety valve automatically keeps
the grill burner lit).
• Ensure that you avoid contact with any
flame of hot parts.
If for any reason the flame should extinguish
turn the control knob to the OFF position,
leave for at least 1 minute and then re-ignite.
9
Accessible parts may become hot
when the grill is in us. Children should be
kept away.
The grill pan will become hot
during use, always use oven gloves when
removing or replacing a hot grill pan.
Grilling
When using the grill it has to be
supervised, the oven door opened and
the grill deflector “A” in place.
When grilling, only the top burner is heating. It
is not necessary to preheat the grill.
1. Insert the food on the 2nd level.
2. Turn the knob to position “grill”.
Adjust the grid and pan position to allow for
different thickness of food. Position the food
closer to the grill for faster cooking and
further away for slower cooking.
Grilling meat
When using the grill it has to be
supervised, the oven door opened
and the grill deflector “A” in place.
Attention: when turning on the
oven and grill burner the oven
door has to be opened.
• Prepare the meat to be grilled, lightly brush
it with oil on both sides.
• Place it on the roasting grid.
• Turn the oven/grill control knob to position
“grill”.
• Slide the roasting grid together with the
roasting tray in the guide 2.
• When the first side is brown, turn the
meat without pricking it in order that the
juices are not lost.
• Grill the second side.
Cooking time is determined by the thickness
of the piece to be grilled not by its weight.
Browning
Heat comes from the top of the oven. It is
suitable for grilling meat (steak, bacon etc…)
that remains tender, for toast or to brown
already cooked dishes.
• Turn the oven/grill control knob to the
“grill” position.
• Place the dish on the grid and slide it on
shelf guide 2 or 3.
• Leave the dish under the grill for a few
minutes.
When you have finished using the
grill please remove the grill deflector.
10
COOKING CHART
Food
Tray type or
dimension
(dxwxh) cm
Material of
the tray
No.
of
tray
Shelf
pos.
Preheating
Thermostat
pos.
Cooking
Time
(min)
Thermostat
pos.
Time
(min)
Roasting meal
- beef
- lamb
Roasting tray
delivered with the Enameled
cooker
- pork and veal
1
2
5
15
5
1
2
5
15
5
1
2
5
15
5
1
2
5
15
5
20 min. for each
0.5 Kg / rare
25 min. for each
0..5 Kg/medium
30min. for each
0.5 Kg/well done
25 min. for each
0.5 Kg/ medium
30min. for each
0.5 Kg/well done
30 min. for each
0.5 Kg/ medium
35min. for each
0.5 Kg/well done
Poultry
- chicken
- turkey below 4.5 Kg
- duck
Roasting tray
delivered with the Enameled
cooker
1
2
4
15
4
1
2
5
15
5
1
1
Grill
15
25-30 min. for
each 0.5 Kg
25 min. for each
0.5 Kg
25 min. for each
0.5 Kg
Grilling
- half cut chicken
Roasting tray
and grilling oven
grid delivered
with the cooker
35-45 min for one
side
25-35 for other
side
Grill
Cakes
- scones
- fettles sponge cake
- rich fruit cake
- small cake
- Victoria sandwich
- apple pie
33x28x0.6
33x28x0.6
Ø 26x5
Ø 23x7.6
33x28x0.6
33x28x0.6
Ø 20.5x3.5
Ø 20.5x3.5
Ø 20x5
Ø 20x5
Aluminum
Aluminum
Aluminized
Tinned steel
Aluminum
Aluminum
Aluminized
Aluminized
Aluminized
Aluminized
21)
1
14)
13)
21)
14)
21)3
13)
22)4
14)
2 and 3
3
2
2
2 and 3
2
2 and 3
2
2
2
8
8
4
1
5
5
5
5
6
6
20
20
15
15
1
15
15
15
15
15
8
8
4
1
5
5
5
5
6
6
15-20
15-20
30-35
120-150
20-25
20-25
25-35
25-30
80-90
75-85
19.5x9.3x5.5
19.5x9.3x5.5
Tinned steel
Tinned steel
35)
13)
2
2
7
7
20
20
7
7
35-45
30-35
Yeast mixture
- bread 1.35 Kg
- bread 0.45 Kg
NOTE: d = deepness; w = width; h = height
Remarks: The recommended cooking conditions give the best results. The roasting tray must be on
the level 1 at all cakes and yeast mixtures.
11
1)
If you should cooking more than one tray, you
can take the top tray out of the oven when the
cakes are finished and move the lower tray to
the higher shelf to finish the cooking (about 5
min.)
2)
These two pans are positioned on the same
shelf, at the diagonal of the oven grid
3)
Put the dishes in the center of the shelf
4)
The oven grid in the position
5)
The longer side of the tray must be parallel
with oven door
Using the Hob
The Hob Burners
The symbol on the knob corresponds to a
symbol on the control panel (See description
of appliance).
Off
Maximum level
Minimum level
Use the maximum level for boiling and the
minimum for simmering.
Always choose positions between the
minimum and maximum, never between
maximum and off.
Ignition of the burners
• Push the knob and turn it left to the symbol
“big flame”.
• At the same time, push the electronic
ignition knob (see fig). Keep it pushed until
the gas ignites (1 spark / second).
• Release the knob and watch that the
burner has ignited.
• Upon ignition, adjust the flame as
required.
OR
Power Cut
Push the corresponding knob in completely
and turn it left to the symbol “large flame”
symbol and ignite with a match.
12
• Release the knob and watch that the
burner has ignited. Upon ignition, adjust
the flame as required.
• If for any reason the flame should
extinguish turn off the relevant control
knob, leave for at least one minute and
then re-ignite.
Extinguishing of burners
Turn the knob clockwise to mark « ».
Do not put anything on the hob that
is liable to melt.
Selecting the Correct burner
Above every knob there is a symbol for the
corresponding burner.
For good cooking results, always choose
pans, which correctly fit to the diameter of
the burner used (see figs). Choose thick, flat
bottom pots.
We recommend the flame is lowered as soon
as the liquid starts boiling.
For a correct ignition always keep the burner
ring and the spark plugs clean.
Good use
Bad use
(Power waste)
The following diameter pans can be used:
Burner
Rapid
Semi-Rapid
Auxiliary
Power
(kW)
2,60
2,00
1,00
min.
165
140
120
Diameter (mm)
max.
260
220
160
Accessories delivered with the appliance
The following accessories are supplied with
your appliance.
• Grill deflector - To be used when the grill
is in operation.
• Shelf for placing dishes on (roast, pastry
mounds)
The dish should be placed in the middle of
the shelf to balance the weight.
• Dripping pan / roasting tray with roasting
grid in it.
In addition to the accessories supplied we
recommend you only use heatproof
dishes/pans (according to the
manufacturer’s instructions).
13
MAINTENANCE AND CLEANING
The oven should be kept clean at
all times. A build-up of fats or other
foodstuffs could result in a fire,
especially in the grill pan.
Before cleaning, ensure all control
knobs are in the OFF position, and the
appliance has cooled completely.
Before any maintenance or
cleaning can be carried out, you must
DISCONNECT the cooker from the
electricity supply.
Cleaning materials
Before using any cleaning materials on your
oven, check that they are suitable and that
the manufacturer recommends their use.
Cleaners that contain bleach should
NOT be used as they may dull the surface
finishes. Harsh abrasives should also be
avoided.
External cleaning
Regularly wipe over the control panel, oven
door and door seal using a soft cloth well
wrung out in warm water to which a little
washing up liquid has been added.
In the case of stainless steel parts, you may
use commercially available stainless steel
cleaners with care. These also provide a
protective film against finger marks.
To prevent damaging or weakening
of the door glass panels avoid the use of
the following:
• Household detergent and bleaches
• Impregnated pads unsuitable for non
stick saucepans
• Brillo/Ajax pads or steel wool pads
• Chemical oven pads or aerosols
• Rust removers
• Bath/Sink stain removers
14
Oven Cavity
The enamelled oven cavity is best cleaned
whilst the oven is still warm.
Wipe the oven over with a soft cloth
soaked in warm soapy water after each
use. From time to time it will be
necessary to do a more thorough
cleaning, using a proprietary oven
cleaner.
DO NOT clean the oven door while
the glass panels are warm. If this
precaution is not observed the glass
panel may shatter.
If the door glass panel becomes chipped
or has deep scratches, the glass will be
weakened and must be replaced to
prevent the possibility of the panel
shattering.
Contact your local Service Centre who
will be pleased to advise further.
IMPORTANT: The inner door glass must be
in place when using the oven.
Hob
After every use wipe with a soft cloth well
wrung out in warm water to which a little
washing up liquid has been added, avoiding
any leakage through the holes of the hob.
Rinse and dry with a soft cloth.
To remove more stubborn stains, wet and
leave to dissolve, do not scratch and avoid
the use of abrasive or caustic products that
could damage the enamel.
Burners
The burner caps and crowns can be
removed for cleaning.
Wash the burners caps and crowns using
hot soapy water, and remove marks with a
mild paste cleaner. A well-moistened soap
impregnated steel wool pad can be used
with caution, if the marks are particularly
difficult to remove.
Burner
cap
Burner
ring
IIgnition
After cleaning, be sure to wipe dry with a
soft cloth.
SOMETHING NOT WORKING
If the appliance is not working correctly,
please carry out the following checks, before
contacting your local Service Force Service
Centre.
Symptoms
IMPORTANT: If you call out an engineer
to a fault listed below, or to repair a fault
caused by incorrect use or installation, a
charge will be made even if the appliance
is under guarantee.
Solutions
1. No burner ignition
Check that:
•
Gas supply is completely open
•
The position of gas pipe is correct
•
The burner is not wet
•
The burner cap and ring burner have been
replaced correctly after cleaning
2. The gas ring burns unevenly
Check that:
•
The main jet is not blocked and the ring burner is
clean of food particles
•
The burner cap and ring burner have been
replaced correctly after cleaning
3. One of the oven or grill burners does not Check that:
ignite
•
The burner is in its correct place
•
The burner is not wet
•
The control knob has been pressed for 10
seconds upon ignition
15
4. Cooking results are not satisfactory
Check that:
•
The correct temperature has been selected
•
The cooking time is adapted
•
The grill is placed correctly in the oven
5. The oven smokes
Check that:
•
The oven does not need cleaning
•
The food does not spill over
•
There is no excessive fat / juice on the oven sides
If after these checks, the appliance still does
not operate correctly, contact your local
Service Force Centre. When you contact the
Service Force Centre you will need to give
the following details:
* The rating plate can be found on the lower
left hand corner of the front frame of the
cavity.
Please note that valid purchase receipt or
guarantee documentation is required for
in-guarantee service calls.
16
1.
2.
3.
4.
Your name, address and postcode.
Your telephone number
Clear and concise details of the fault
The model and serial number of the
appliance (found on the rating plate*)
5. The purchase date
INSTRUCTIONS FOR THE INSTALLER
Technical features
Free standing
Hob
Class 1
Pan support
Front right
Back right
Front left
Back left
Hob ignition
Oven
Oven
Oven power
Grill
Grill power
Oven ignition
Accessories
Dimensions
Trivet
Dripping pan / roasting tray
Oven grid
Grill deflector
Legs
Height to the hob
Width
Depth
Enamelled
Rapid
Auxiliary
Semi-rapid
Semi-rapid
2,60 kW
1,00 kW
2,00 kW
2,00 kW
Spark
Gas
3,20 kW
Gas
2,50 kW
Spark
Chromed
Enameled
Chromed
Enameled
880- 890 mm
500 mm
600 mm
This appliance complies with the following EEC Directives :
2006/95 ; 73/23 (Low Voltage Directive) and subsequent modifications,
89/336, 90/31, 93/68 (Electromagnetic Compatibility Directive) and subsequent modifications,
90/396 (Gas Appliance Directive) 93/68 (General Directives) and subsequent modifications.
17
ADVICE FOR SAFETY
Gas connections
•
•
•
•
•
Before installation ensure gas type and
pressure and the pre-setting of the
appliance are consistent.
This appliance must be installed only in
a room with good ventilation.
This appliance must not connect to a
flu. It has to be installed and connected
in accordance with the rules in force.
Special attention should be paid to
ventilation requirements.
The adjacent furniture panels have to
be heat resistant or protected by such
material.
The gas type for this appliance is stated
on the rating plate.
Connection to gas supply.
Check that the gas flow and the diameter of
the supply pipe are sufficient to supply all
the appliances of the installation.
• Check that all connections are tight.
• Install an accessible and visible gas tap
to isolate the appliance.
- Installation of flues and ventilation
for gas appliances of rated input not
exceeding 60 kW (1st, 2nd and 3rd family
gases) – Part 2 Specification for
installation of ventilation for gas
appliances – BS 5440 Current editions;
- Gas burning appliances – Part 3
Domestic cooking appliances burning
gas – BS 5386 Current editions;
- Specification for installation of low
pressure gas pipe wo rk of up to 20mm
(R1) in domestic premises (2nd family
gas) – BS 6891 Current editions;
Pipe threads for tubes and fittings where
pressure-tight joints are made on the
threads (metric dimensions) – BS 21
Current editions;
18
- Flexible hoses, end fittings and
sockets for gas burning appliances – BS
669 Current editions;
- Installation of domestic gas cooking
appliances (1st, 2nd and 3rd family gases) –
BS 6172: 1990 Current editions;
For appliances installed in the Republic
of Ireland please refer to NSAI-Domestic
Gas Installation IS813 Current editions.
Electrical connections
Any electrical work required to
install this cooker should be carried out
by a qualified electrician or competent
person, in accordance with the current
regulations.
THIS COOKER MUST BE EARTHED.
The manufacturer declines any
liability should these safety measures not
be observed.
This cooker is designed to be connected
to a 230-240V AC 50Hz electrical supply.
Before switching on, make sure the
electricity supply voltage is the same as that
indicated on the cooker rating plate. The
rating plate is located on the oven frame.
The cooker is supplied with a 3-core flexible
supply cord incorporating a 13amp plug
fitted. In the event of having to change the
fuse, a 5amp ASTA approved (BS 1362)
fuse must be used. Should the plug need to
be replaced for any reason, the wires in the
mains lead are coloured in accordance with
the following code:
Green and Yellow
Blue
Brown
-
-
- Earth
- Neutral
- Live
Connect the green and yellow (earth)
wire to the terminal in the plug, which is
marked with the letter 'E' or the earth
or coloured green and yellow.
symbol
Connect the blue (neutral) wire to the
terminal in the plug, which is marked
with the letter 'N' or coloured black.
Connect the brown (live) wire to the
terminal in the plug, which is marked
with the letter 'L' or coloured red.
NOTE: The earth wire should be about 2 cm
longer than the live and neutral wires.
Permanent Connection
In the case of a permanent connection, it is
necessary that you install a double pole
switch between the cooker and the electricity
supply (mains), with a minimum gap of 3mm,
between the switch contacts and of a type
suitable for the required load in compliance
with the current electric regulations.
The switch must not break the yellow and
green earth cable at any point.
Ensure that the cooker supply cord
does not come into contact with surfaces
with temperatures higher than 50 deg. C.
Upon completion there must be no cut, or
stray strands of wire present and the cord
clamp must be secure over the outer
sheath.
A cut off plug inserted into a 13amp socket is a serious safety (shock)
hazard.
Ensure that the cut off plug is disposed of
safety.
Before connecting check that:
The plug used for connection is easily
accessible when the appliance is installed.
19
INSTALLATION
Location of appliance
The appliance must not be installed in a bedsitting room of volume less than 20m3 or in a
bathroom or shower room. It is essential that the
appliance is positioned as in the enclosed figure
i.e. shelves, wall cabinets and cooker hoods
must be fitted a minimum of 690mm directly
above the hob and 400mm above the hob when
fitted in line with the outside of the appliance. If
the units are intended to be fitted adjacent to the
appliance but less than 400mm above the hob,
then a minimum space of 100mm must be
maintained between the sides of the unit and
the appliance (see fig).
If fitted next to or between two base units a
minimum space of 1mm must be left between
each unit and the sides of the appliance. The
levelling feet fitted to the appliance will
achieve a nominal height to hob of
900mm+10mm.
The appliance must be installed in
accordance with EN 1116-1995, regarding
the depth of the superior furniture.
690
690
max 400
100
400
min 600
C
C
1 G
2
34
5678
less than
400
G
21
3
45678
min 570
L.P.G. cookers or ovens MUST NOT
be installed below ground level, i.e. in a
basement, or aboard any boat, yacht or
other vessel.
20
The cooking appliance must be
fitted with a stability chain firmly secured
to the wall.
Stability
hook
Firmly fix
chain to rear
of cooker
Stability
chain
Chain to be as
short as
practicable
Ventilation
The room containing the cooker should have an
air supply in accordance with B.S. 5440: Part 2:
Current Editions.
The following requirements for ventilation
must be met.
The cooker should not be installed in a bed
sitting room with a volume of less than 20m3, if
it is installed in a room of volume less 5m3 an
air vent of effective area of 110cm2 is required;
if it is installed in a room of volume between
5m3 and 10m3, an air vent of effective area
50cm2 is required, while if the volume exceeds
11m3 no air vent is required. However, if the
room has a door, which opens directly to the
outside, no air vent is required even when the
volume is between 5m3 and 11m3.
If there are other fuels burning appliances in
the same room, B.S. 5440: Part. 2: Current
Editions should be consulted to determine
the requisite air vent requirements.
Leveling
Fix the support with two legs with the washer
and nuts, delivered with the cooker, see the
figure.
• Unscrew the legs as far as possible
(approx. 16mm from fully screwed in).
• Place the plinth (pos.3) so that the
springs (pos.2) reach the threaded area
of the legs and the clamp of the plinth
(pos.4) is in front of the holes (pos.5) on
the under side of the structure.
• Push the plinth towards the appliance
with both hands until the springs fasten
on the legs and the clamps go into the
corresponding holes.
• Adjust the legs as necessary.
4
5
3
2
1
GAS CONNECTIONS
Your cooker is delivered adjusted for the kind
of gas stated on the rating plate.
BACK OF THE COOKER
If the appliance is converted to natural gas
and the pressure for natural gas is 20mbar,
the following methods of connection to the
gas supply must be used:
Right Hand Connection (from front)
Ensure that the rubber hose is not in contact
with any part of the shaded area shown in the
diagram and that the loop of the hose when
connected is not in contact with the floor
when the appliance is in position.
Left Hand Connection (from front)
Ensure that the rubber hose is not in contact
with any part of the shaded area shown in the
diagram and the hose is retained in the clamp
provided, it will be necessary to fit the
maximum length hose when using this
method.
power cord
connection
of flexible
hose
clamps
BACK OF THE COOKER
power cord
connection
of flexible
hose
clamps
21
Fixing and use of the 2 clips provided with
the cooker
The enclosed gas hose fixing clips must be
fixed to the back of the cooker, dependant on
the position of the supply bayonet connector
(see fig.).
When selecting the most suitable position for
the clips, please ensure that the gas hose
cannot come into contact with any part of the
“Hot zone” (indicated by the shaded areas on
the illustration) when pushing the cooker into
its final position.
Finally, secure the hose into the clips.
Rigid Connection
Where it is not possible to make the
connection using a rubber hose, a rigid pipe
work connection must be used.
Recommendations when using an appliance
flexible connector are as follows:
- For NATURAL the gas installation pipes to
the termination point shall comply with:
Specification for installation of lowpressure gas pipe work of up to 20mm
(R1) in domestic premises (2nd family gas)
– BS 6891;
Connection shall be by means of an
appliance flexible connector for use with a
self-sealing plug-in device, complying with:
Flexible hoses, end fittings and sockets for
gas burning appliances – BS 669;
• The appliance flexible connector should
not be subjected to undue forces either in
normal use or whilst connected or
disconnected; The socket which the plug of
the appliance flexible connector fits should be
permanently attached to a firmly fixed gas
installation pipe and positioned such that the
appliance flexible connector hose hangs
freely downwards (see fig.);
22
clip
Clip Position
Options
Right angled
bayonet socket
Distribuitor
incorporating
pipe
spring loaded
Adaptor
valve
backplate
Female
elbow
Copper pipe
Alternative
backplate
elbow
Cooker hose with
bayonet fixing
Straight bayonet
socket
incorporating
spring loaded
valve
Cooker hose with
bayonet fixing
• The appliance flexible connector should
be positioned such that it will not suffer
mechanical damage, e.g. abrasion from the
surrounding kitchen furniture, which may be
moved in use such as a drawer or door, or by
being trapped by any stability device.
The plug-in-connector bayonet should be
accessible for disconnection after moving
the appliance.
CONVERSION OF GAS
Your cooker is designed to work with natural
gas, and is convertible for use with propane
or butane.
The LPG conversion kit is available from your
Service Force Centre and must be fitted by a
Registered engineer/ competent person.
For changing the gas type it is necessary to:
• replace the nozzles (hob, oven and grill);
• adjust the minimum level (hob and
oven);
•
•
adjust the primary air (oven and grill);
check the gas connection;
Stick the label supplied with the
replacement nozzles (from the Service
Force Centre) corresponding to the gas
type utilized.
SPECIFICATION NOZZLES
Table no.1
(Cat : II 2H3+)
Burner
RAPID
SEMI-RAPID
AUXILIARY
OVEN
GRILL
Normal
power
(kW)
2.60
2.50
2.50
2.00
2.00
2.00
1.00
1.00
1.00
3.20
3.20
3.20
2.50
2.50
2.50
Simmer
power
(kW)
By-pass
(mm)
0.72
0.42
0.43
0.32
0.35
0.29
1.00
0.46
-
-
Gas Type
Natural Gas
Butane
Propane
Natural Gas
Butane
Propane
Natural Gas
Butane
Propane
Natural Gas
Butane
Propane
Natural Gas
Butane
Propane
Pressure
(mbar)
20
28-30
37
20
28-30
37
20
28-30
37
20
28-30
37
20
28-30
37
Nozzle
diameter
(mm)
Cons
1.13
0,77
0,77
181,78
178,53
0.96
0,71
0,71
0.70
0,50
0,50
1.30
0,88
0,88
1,15
0,80
0,80
145,43
142,83
72,71
71,41
232,68
228,52
181,78
178,53
g/h
23
Replace the nozzles of the hob burners
Every appliance has spare nozzles for every
type of gas. The whole length of every nozzle
is marked in millimetres on the nozzle.
Before any modifications or
conversion to a different kind of gas, you
must DISCONNECT the cooker from the
electricity supply and ensure that all
control knobs are in the OFF position, and
the appliance has cooled completely.
Hob burners
Remove the pan support;
Remove the caps and the burner
crowns;
• Using a No 7 socket spanner unscrew
the nozzles and replace them with those
required for the type of gas in use (see
table no. 1).
Reassemble the parts following the same
procedure in reverse.
These burners do not need any primary air
regulation.
•
•
Adjustment of minimum level for the hob
burners
The burner is correctly adjusted when the
flame is stable silent and goes out without
any noise.
When changing the type of gas check that the
minimum level is correct. The air admission is
correct when the flame is about 4 mm in
length.
The top burners do not need adjustment of
primary air.
Check that, turning the knob quickly from
the maximum position to the minimum
one, the flame does not go out.
To adjust the minimum level:
• Light the burner
• Turn the knob to the position of the
minimum flame;
• Remove the knob;
24
no air
correct
adjustment
excess of
air
•
Unscrew or screw the by-pass screw
until a regular small flame is reached.
• For LPG screw completely the by-pass
screw.
Reassemble the parts following the same
procedure in reverse.
Check that, when turning the knob quickly
from the maximum position to the minimum
one, the flame does not go out.
Replace the nozzles of the oven burners
Oven burner
To replace the gas oven nozzle, follow this
procedure:
• Check the table no.1 for diameter of
nozzle;
• Remove the oven removable base
panel;
• Remove the screw on the oven burner
rod at the rear of the oven;
• Remove the oven burner by pushing it
backwards.
• Replace the nozzle "C" by means of a
No 10 socket spanner;
Reassemble the parts following the same
procedure in reverse.
Grill burner
To replace the gas grill nozzle, follow this
procedure:
• Remove the grill burner after removing
the fixing screw.
• Replace the nozzle by means of a No 10
socket spanner;
Refit all parts and test.
25
Oven burner
The burner is correctly adjusted when the
flame is stable, silent and goes out without
any noise.
• When the flames are too short, the nozzle
is whistling or the flames have the
tendency to detach from the burner, it
means that there is too much air in the
valve. If there is too much air there is a
risk that the flames will extinguish.
• But, if the flames are too long, soft,
lighting, there is not enough air in the
valves. These flames discolour the bottom
of pans.
• Loosen the fixing screw M.
• Move the air adjuster A forward or
backward until achieving the right mixture
(see table no. 2);
• Tighten the fixing screw M.
Grill burner
• Loosen the screw fixing the Venturi.
• Move the adjusting collar left or right until
achieving the correct flame picture (see
table no. 2).
Tighten the fixing screw.
Adjustment of minimum level
•
•
•
•
•
26
Oven burner
Remove the top pan support as well as
the burner caps and the burner crowns.
Unscrew and remove the 2 top platefixing screws and remove the top plate.
Light the burner knob in the maximum
position and leave the oven door closed
for about 10 min.
Turn the knob slowly to the minimum
position.
Pull off the knob to adjust minimum flow.
Table no.2
Gas type
G20
G30
G31
Air adjusting (mm)
Oven
Grill
3,2
25
3,2
24
3,2
24
air adjusting
Flame adjustment
M
A
opening
adjusting collar
screw
•
•
Unscrew or screw the by-pass screw
until a regular small flame is reached.
For LPG completely tighten the by-pass
screw.
by-pass
The flame shouldn’t extinguish when closing
the oven door.
Grill burner
The grill temperature cannot be adjusted. To
obtain a lower temperature or slower cooking
time the grill pan must be lowered away from
the flame.
After completion of any repairs,
conversion or adjustments, the statutory
safety tests must be carried out.
27
SERVICE AND SPARE PARTS
In the event of your appliance requiring
service, or if you wish to purchase spare
parts, please contact your local Service Force
Centre by telephoning:-
08705 929929
Your telephone call will be automatically
routed to the Service Force Centre covering
your postcode area.
For the address of your local Service Force
Centre and further information about Service
Force, please visit the website at
www.serviceforce.co.uk
In-guarantee customers should ensure
that the checks under the heading
“Something Not Working” have been
made as the engineer will make a charge if
the fault is not a mechanical or electrical
breakdown. Please note that it will be
necessary to provide proof of purchase
for any in-guarantee service calls.
CUSTOMER CARE
For general enquiries concerning your Tricity
Bendix appliance and or for further
information on our products, contact our
Customer Care Department by letter or
telephone as follows:
Customer Care Department
Electrolux Major Appliances
Addington Way
Luton
Bedfordshire, LU4 9QQ
Tel: 08705 727 727 (*)
28
For Customer Service in the Republic of
Ireland please contact us at the address
below:
Tricity Bendix
Electrolux Group ( Ire ) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: + 353 (0) 1 4090 752
Email: [email protected]
(*) Calls to this number may be recorded for
training purposes.
GUARANTEE CONDITIONS
Standard Guarantee Conditions
Exclusions
We Tricity Bendix undertake that if, within 12
months of the date of the purchase, this Tricity
Bendix appliance or any part thereof is proved
to be defective by any reason only of faulty
workmanship or materials, we will, at our
option, repair or replace the same FREE OF
ANY CHARGE for labour, materials or
carriage on condition that:
• The appliance has been correctly
installed and used only on the electricity
supply stated on the rating plate.
• The appliance has been used for normal
domestic purposes only, and in
accordance with the manufacturer's
instructions.
• The appliance has not been serviced
maintained, repaired, taken apart or
tampered with by any person not
authorized by us.
• All service work under this guarantee
must be undertaken by a Tricity Bendix
Service Force Centre.
• Any appliance or defective part replaced
shall become the Company's property.
• This guarantee is in addition to your
statutory and other legal rights.
Home visits are made between 8.30am and
5.30pm Monday to Friday. Visits may be
available outside these hours, in which case
a premium will be charged.
This guarantee does not cover:
• Damage or calls resulting from
transportation, improper use or neglect,
the replacement of any light bulbs or
removable parts of glass or plastic.
• Costs incurred for calls to put right an
appliance which is improperly installed
or calls to appliance outside the United
Kingdom.
• Appliances found to be in use within a
commercial or similar environment, plus
those, which are the subject to rental
agreements.
Products of Tricity Bendix manufacture
which are not marketed by Tricity Bendix.
29
European Guarantee
If you should move to another country within
Europe then your guarantee moves with you
to your new home subject to the following
qualifications:
• The guarantee starts from the date you
first purchased your product.
• The guarantee is for the same period and
to the same extent for labour and parts as
exists in the new country of use for this
brand or range of products.
• This guarantee relates to you and cannot
be transferred to another user.
• Your new home is within the European
Community (EC) or European Free Trade
Area.
• The product is installed and used in
accordance with our instructions and is
only used domestically, i.e. a normal
household
• The electrical supply complies with the
specification given in the rating label.
The product is installed taking into account
regulations in your new country.
30
Before you move, please contact your
nearest Customer Care Centre, listed below,
to give them details of your new home. They
will then ensure that the local Service
Organization is aware of your move and able
to look after you and your appliances.
France Senlis
Germany Nürnberg
Italy Pordenone
Sweden Stockholm
UK Luton
+33 (0) 3 44 62 20 13
+49 (0) 800 234 7378
+39 (0) 800117511
+46 (0) 20 78 77 50
+44 (0) 08705 727 727
www.electrolux.com
Albania
Belgique/België/
Belgien
Česká republika
Danmark
Deutschland
Eesti
+35 5 4 261 450
Rr. Pjeter Bogdani Nr. 7 Tirane
+32 2 363 04 44
Bergensesteenweg 719, 1502 Lembeek
+420 2 61 12 61 12
+45 70 11 74 00
+49 180 32 26 622
+37 2 66 50 030
España
+34 902 11 63 88
Budějovická 3, Praha 4, 140 21
Sjællandsgade 2, 7000 Fredericia
Muggenhofer Str. 135, 90429 Nürnberg
Mustamäe tee 24, 10621 Tallinn
Carretera M-300, Km. 29,900
Alcalá de Henares Madrid
France
www.electrolux.fr
Great Britain
+44 8705 929 929
Hellas
Hrvatska
Ireland
Italia
Latvija
Lietuva
Luxembourg
+30 23 10 56 19 70
+385 1 63 23 338
+353 1 40 90 753
+39 (0) 434 558500
+37 17 84 59 34
+370 5 2780609
+35 2 42 43 13 01
Magyarország
+36 1 252 1773
Nederland
+31 17 24 68 300
Norge
Österreich
Polska
+47 81 5 30 222
+43 18 66 400
+48 22 43 47 300
Portugal
+35 12 14 40 39 39
Romania
Schweiz/Suisse/
Svizzera
Slovenija
+40 21 451 20 30
Addington Way, Luton, Bedfordshire
LU4 9QQ
4, Limnou Str., 54627 Thessaloniki
Slavonska avenija 3, 10000 Zagreb
Long Mile Road Dublin 12
C.so Lino Zanussi, 26 - 33080 Porcia (PN)
Kr. Barona iela 130/2, LV-1012, Riga
Verkių 29, LT-09108 Vilnius
Rue de Bitbourg, 7, L-1273 Hamm
H-1142 Budapest XIV,
Erzsébet királyné útja 87
Vennootsweg 1, 2404 CG –
Alphen aan den Rijn
Risløkkvn. 2 , 0508 Oslo
Herziggasse 9, 1230 Wien
ul. Kolejowa 5/7, Warsaw
Quinta da Fonte - Edificio Gonçalves
Zarco - Q 35
2774-518 Paço de Arcos
Str. Garii Progresului 2, S4, 040671 RO
+41 62 88 99 111
Industriestrasse 10, CH-5506 Mägenwil
+38 61 24 25 731
Slovensko
+421 2 43 33 43 22
Suomi
+35 8 26 22 33 00
Sverige
+46 (0)771 76 76 76
Türkiye
+90 21 22 93 10 25
Tržaška 132, 1000 Ljubljana
Electrolux Slovakia s.r.o., Electrolux
Domáce spotrebiče SK, Seberíniho 1, 821
03 Bratislava
Konepajanranta 4, 28100 Pori
Electrolux Service, S:t Göransgatan 143, S105 45 Stockholm
Tarlabaşı caddesi no : 35 Taksim İstanbul
Россия
+7 095 937 7837
129090 Москва, Олимпийский проспект,
16, БЦ "Олимпик"
31
www.electrolux.com
342 702 367 – 00 – 05042007
Subject to change without notice