Flymo MICROCOMPACT 300 Instruction manuals

TIO
A
M
R
N
NFO
I
T
TA N se
R
O
ence
I M P before u re refer
tu
Read in for fu
ta
& re
For all customer enquiries or for replacement parts, contact:-
☎
01325 300303
www.flymo.com
[email protected]
1
Carton Contents
switchbox
start/stop lever
cable clip x 2
nut x 2
(if applicable)
bolt x 2
upper handle
plastic handle
knob x 2
washer x 2
lower handle
electric cable
with moulded
on plug
grassbox
fixing pin x 2
hood
instruction
manual
spanner/scraper tool
cutting height spacers (1 fitted to
lawnmower & 2 in loose parts pack
IMPORTANT !
Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
IF ANY PARTS ARE MISSING CONTACT:Electrolux Outdoor Products Customer Service Department direct
Telephone :
01325 300303
Fax :
01325 318193
Safety
If not used properly this lawnmower can be dangerous! This lawnmower can cause serious injury
to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this lawnmower. The operator is responsible for following the
warning and safety instructions in this manual and on the lawnmower. Never use the mower unless
the grassbox or guards provided by the manufacturer are in the correct position.
Explanation of Symbols on the
Micro Compact 300 Plus
Warning
Keep bystanders away. Do not mow
whilst people especially children or pets
are in the mowing area
Read the user instructions carefully to
make sure you understand all the controls and what they do.
Beware of severing toes or hands.
Do not put hands or feet near a rotating
blade.
Switch off! Remove plug from mains
before adjusting, cleaning or if cable is
entangled or damaged. Keep the cable
away from the blade.
Blade continues to rotate after the
machine is switched off.
Wait until all machine components have
completely stopped before touching them.
Always keep the lawnmower on the
ground when mowing. Tilting or lifting the
lawnmower may cause stones to be
thrown out
STOP
Do not mow in the rain or leave the lawnmower outdoors while raining
2
General
1. Never allow children or people unfamiliar with
these instructions to use the mower. Local regulations may restrict the age of the operator.
2. Only use the lawnmower in the manner and for
the functions described in these instructions.
3. Never operate the lawnmower when you are
tired, ill or under the influence of alcohol, drugs
or medicine.
4. The operator or user is responsible for accidents or hazards occurring to other people or
their property.
Electrical
1. The British Standards Institute recommend the
use of a Residual Current Device (R.C.D.) with
a tripping current of not more than 30mA.
Even with a R.C.D. installed 100% safety cannot be guaranteed and safe working practice
must be followed at all times. Check your
R.C.D. every time you use it.
2. Before use, examine cable for damage, replace
it if there are signs of damage or ageing.
3. Do not use the lawnmower if the electric cables
are damaged or worn
4. Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is
damaged. Do not touch the electric cable until
the electrical supply has been disconnected.
Do not repair a cut or damaged cable. Replace
it with a new one.
5. Your extension cable must be uncoiled, coiled
cables can overheat and reduce the efficiency
of your mower.
6. Keep cable away from lawnmower, always work
away from the power point mowing up and
down, never in circles.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting any plug, cable connector or extension
cable.
9. Switch off, remove plug from mains and examine electric supply cable for damage or ageing
before winding cable for storage. Do not repair
a damaged cable, replace it with a new one.
Use only Flymo replacement cable.
10. Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12. Never pull on the cable to disconnect any of the
plugs.
13. Use only on AC mains supply voltage shown on
the product rating label.
14. Our products are double insulated to EN60335.
Under no circumstance should an earth be connected to any part of the product.
Preparation
1. While using your product always wear substantial footwear and long trousers.
2. Make sure the lawn is clear of sticks, stones,
bones, wire and debris; they could be thrown by
the blade.
3. Before using the machine and after any impact,
check for signs of wear or damage and repair
as necessary.
4. Replace worn or damaged blades together with
their fixings in sets to preserve balance.
Use
1. Use the lawnmower only in daylight or good
artificial light.
2. Avoid operating your lawnmower in wet grass,
where feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and
wear non-slip footwear.
5. Mow across the face of slopes, never up and
down.
6. Exercise extreme caution when changing direction on slopes. Walk never run.
7. Mowing on banks and slopes can be dangerous. Do not mow on banks or steep slopes.
8. Do not walk backwards when mowing, you
could trip.
9. Never cut grass by pulling the mower towards
you.
10. Switch off before pushing the mower over surfaces other than grass.
11. Never operate the lawnmower with damaged
guards or without guards in place.
12. Keep hands and feet away from the cutting
means at all times and especially when switching on the motor.
13. Do not tilt lawnmower when the motor is running, except when starting and stopping. In this
case, do not tilt more than absolutely necessary and lift only the part which is away from
the operator. Always ensure that both hands
are in the operating position before returning
the appliance to the ground.
14. Never pick up or carry a mower when it is operating or still connected to the mains supply.
15. Remove the plug from the mains :
before leaving the mower unattended for any
period;
before clearing a blockage;
before checking, cleaning or working on the
appliance;
if you hit an object. Do not use your lawnmower until you are sure that the entire lawnmower
is in a safe operating condition.;
if the lawnmower starts to vibrate abnormally.
Check immediately. Excessive vibration can
cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure
the lawnmower is in safe working condition.
2. Check the grassbox/grassbag frequently for
wear or deterioration.
3. Replace worn or damaged parts for safety.
4. Only use the replacement blade, blade bolt,
spacer and impeller specified for this product.
5. Be careful during adjustment of the lawnmower
to prevent entrapment of the fingers between
moving blades and fixed parts of the machine.
3
CABLES
IMPORTANT
•
Use only 1.00mm2 size cable up to 30 metres
length maximum.
Maximum rating :
1.00mm2 size cable, 10 amps 250 volts AC.
•
THE MICRO COMPACT 300 PLUS IS SUPPLIED
WITH AN ELECTRIC MAINS CABLE WIRED
DIRECTLY INTO THE PRODUCT
1. Flymo Mains Cables and Extension Cables are
available from your local Electrolux Outdoor
Products Approved Service Centre.
2. Do not wire an extension cable directly to your
product yourself. Please contact your local
Electrolux Outdoor Products Approved Service
Centre for further information on the connectors
and kits available.
3. Only use extension cables specifically designed for
outdoor use.
CONNECTORS
IMPORTANT
•
Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
•
All Flymo connectors and cables are of splashproof
construction. They are not waterproof and must
not be left outside permanently nor should they be
submerged or immersed in water. Do not let cable
lay or trail through pools of water or splashed with
water from hose pipes.
MAINS PLUG REPLACEMENT
IMPORTANT
•
If the plug supplied is cut off it should be
destroyed. There is an electric shock hazard if
a cut off plug is inserted into a 13 amp socket.
1. No earth required. Flymo products are double
insulated to EN60335 and under no circumstances
should an earth be connected to any part of the
product.
A
lower handle
2.
3.
Ensure the mains voltage suits your product
IMPORTANT!
E
L
F
U
S
E
BLACK
OR N
BLUE
4.
5.
6.
7.
RED
OR
BROWN
The wires in the mains lead are coloured in accordance with the following code:
BLUE
NEUTRAL
BROWN LIVE
The wire which is coloured BLUE must be connected to the Terminal which is marked with the letter
'N' or coloured BLACK.
The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter 'L' or coloured RED.
It is important that the outer sheath is clamped correctly into the 3-pin plug.
If in doubt consult your local Service Repairer or
qualified electrician before the machine is used.
A 13 Amp fuse must be fitted to the Mains Plug.
The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution.
If your product is hard wired i.e. non-detachable
mains electric cable, a conversion kit and extension cable is available from all Electrolux Outdoor
Products Approved Service Centres which can be
found in your local Yellow Pages.
Assembly Instructions
B
lock-off
button
handle
knob
nut
bolt
washer
fixing pin
Fitting the Lower Handles to Your Lawnmower (A)
1. Place the end of the lower handle into the slots.
2. Secure lower handles to hood by firmly pushing
fixing pin through holes in hood and handle.
3. Repeat on the other side.
•
NOTE: Should a problem occur when securing
handle to hood with the fixing pin, carefully lever
fixing pin out of location and repeat steps 1 to 3
above.
Fitting Upper Handles to Lower Handles (B)
1. Ensure the upper handle is located correctly with
the lock-off button on the switchbox uppermost.
2. Ensure the upper handle and the lower handle
are aligned correctly.
3. Insert the nut into the handle knob. (if applicable)
4. Fit the bolts, washers and handle knobs.
5. Fit the cable to the handles with the clips provided. Make sure the cable is not trapped between
the handles.
4
Handle Adjustment
STOP THE LAWNMOWER AND WAIT
C
• WARNING!
UNTIL THE BLADE HAS STOPPED ROTATING
BEFORE ADJUSTING THE HANDLE.
• NOTE! REMOVAL OF LOWER HANDLE FIXING
PINS IS NOT REQUIRED TO ADJUST THE HANDLE
TO ADJUST THE HANDLE (C)
1. Hold handle as illustrated.
2. Take the weight of the handle with your right hand...
3. ...then grip the lower part of the handle with your left
hand...
4. ...and pull the lower handle towards you with your left
hand.
5. Move to forward or down position as required.
HANDLE IN FORWARD POSITION
Follow procedure described in "TO ADJUST THE HANDLE" and push handle forward until it stops.
HANDLE IN DOWN POSITION
Follow procedure described in "TO ADJUST THE HANDLE" and move handle downward until it stops.. NOTE The handle does not rest flat on the ground.
HANDLE IN OPERATING POSITION
Adjustment is not required to move the handle to
the operating position
Simply pull down from the forward position or lift up
from the down position until the handle is in the most
comfortable operating position.
PULL
LOWER
HANDLE
FORWARD
POSITION
DOWN
POSITION
Grassbox
D
Fitting the grassbox
• IMPORTANT! Before using your lawnmower - make
sure the grassbox is securely located inside the lip
on the hood indicated in figure D.
Removing and Emptying the grassbox
• Stop the lawnmower and wait until the blade has
stopped rotating BEFORE removing the grassbox.
1. Hold the grassbox by the moulded handle recess
and support grassbox base with the other hand.
2. Move grassbox to emptying site and press release
button to open grassbox as in figure E.
3. Ensure the grassbox is clean BEFORE closing and
refitting the grassbox.
The grassbox should be in the closed position
prior to fitting.
E
lip on the
hood
Starting and Stopping
F
To Start your Lawnmower
1. Form loop in mains cable and push the loop
through the slot as illustrated in picture (F)
2. To secure, position loop over the hook and pull the
cable back through the slot as illustrated in picture (G).
3. Connect plug to mains.
4. Move handle to the mowing position.
5. To prevent a ring being cut in your lawn and to
clear any residual grass in the collection chute, tilt
your lawnmower slightly (H).
OPERATING
POSITION
H
G
J
The switchbox is provided with a lock-off button
(J1) to prevent accidental starting.
1
5
Starting and Stopping cont...
K
The Micro Compact uses an advanced belt drive system,
between the motor and the blade which improves cutting
power and flotation in all conditions. Due to the high turning
force (Torque) which this motor develops, a light squeak
may be heard when the machine is started, this is quite normal and will not effect the performance of the product.
6. Press and hold the lock-off button (J) on the switchbox, then squeeze one of the Start/Stop levers
towards the upper handle (K).
7. Continue to squeeze the start/stop lever towards the
upper handle and release the lock-off button.
8. When the lawnmower has reached full speed gently
lower it onto the lawn.
• NOTE: There are two start/stop levers fitted. Either
one can be used for starting the lawnmower.
• IMPORTANT: Do not use the start/stop levers
intermittently
To Stop your Lawnmower
1. To prevent a ring being cut in your lawn and to clear
any residual grass in the collection chute, tilt your
lawnmower slightly (H).
2. Release the pressure on the Start/Stop lever.
How to Mow
1.
2.
Start mowing the edge of the lawn nearest to the
power point so the cable is laid out on the lawn
you have already cut.
Cut your grass twice a week during the growing
season, your lawn will suffer if more than a third of
its length is cut at one time.
Do Not Overload Your Mower: Mowing long thick grass may
cause the motor speed to drop, you will hear a change in the
motor sound. If the motor speed drops you may overload your
lawnmower which may cause damage. When mowing in long
thick grass a first cut with the cutting height set higher will help
reduce the load. See Adjusting the Cutting Height.
Remember : for best grass collection, always mow in a straight line, do not swing the lawnmower from side to side
Note : If a trail of grass is left by your lawnmower this indicates that your cutting height needs to be raised or the
grassbox is full. If the grassbox is full, empty is as described in "Removing and emptying the grassbox". Fit the
grassbox, start the lawnmower and mow over the grass trail to collect any residual grass.
Adjusting the Cutting Height
L
blade bolt
cutting
height
spacers
MAXIMUM
3
fan
blade
✓
X
Always handle the blade with care - sharp edges
could cause injury. USE GLOVES. Never use more
than 3 Cutting Height Spacers. Spacers must only
be fitted between the blade and the fan and NEVER
between the blade and the bolt.
1. Remove the blade bolt, and blade as described in
Removing the Blade and Fan.
2. For a Lower Cut - Add spacers to a maximum of 3.(L)
3. For a Higher Cut - Take spacers away.
4. Refit the blade as described in Fitting the Blade and Fan.
Removing the Blade and Fan
1. To remove the blade bolt, hold the fan firmly and with
the spanner provided loosen the blade bolt by turning
it anti-clockwise (M).
2. Remove the blade bolt, blade, spacers, fan and
insert.
3. Inspect for damage and clean as necessary.
• Renew your metal blade after 50 hours mowing or
2 years whichever is the sooner - regardless of
condition.
Fitting the Blade and Fan
M
• If the blade is cracked or damaged replace it with
a new one.
• Never use a blade bolt if the insulated head is
damaged cracked or missing.
1. Ensure the insert and fan are located correctly.(M)
2. Place the spacers onto the fan ensuring the peg have
located into the holes.(M)
3. Place the blade onto the spacers ensuring the pegs
have located into the holes on the blade and ensuring
the blade is positioned as illustrated in Figure M.
4. Place the blade bolt through the centre hole of the blade.(M)
5. Tighten down clockwise by hand.
6. Hold the fan firmly and tighten the blade bolt with the
spanner provided. (M)
6
Caring for your Lawnmower
N
Cleaning (N)
• USE GLOVES
• IMPORTANT
It is very important that you keep your lawnmower
clean. Grass clippings left in any of the air intakes or
under the hood could become a potential fire hazard.
1. Remove grass from under the hood with a piece of
wood or similar.
2. Using a soft brush - remove grass clippings from all
air intakes and the grassbox.
3. Remove the blade, see Figure M, to gain access to
the fan and clean with a soft brush.
4. Wipe over the surface of your lawnmower with a dry cloth.
• IMPORTANT
Never use water for cleaning your lawnmower. Do not
clean with chemicals, including petrol, or solvents some can destroy critical plastic parts.
At the End of the Mowing Season
1. Replace blade, bolts, nuts or screws, if necessary.
2. Clean your lawnmower thoroughly.
3. Ask your local Service Centre to clean the air filter thoroughly and carry out any service or repairs required.
4. Make sure that the electric cable is coiled properly.
Carrying your Lawnmower (P): Hold as illustrated in
Figure S. Ensure the blade is facing away from you.
Storing your Lawnmower (Q): Store in a dry place
where your lawnmower is protected from damage.
P
Q
Fault Finding Hints
Fails to Operate
1. Is the Power Turned On?
2. Check the fuse in the plug, if blown replace.
3. Fuse continues to blow?
Immediately disconnect from the mains electricity supply and consult your local approved Service Centre.
Poor Flotation
1. Disconnect from the mains electricity supply.
2. Clean the underside of the hood and the fan blades.
3. Raise to a higher height of cut. See Adjusting the Height of Cut.
4. If poor flotation persists?
Disconnect from the mains electricity supply and
consult your local approved Service Centre.
Poor Collection
1. Is the grassbox fitted correctly?
2. Are you mowing in straight lines?
3. Are you cutting more than one third of the grass length?
4. Do you need to raise the cutting height?
5. Follow the procedure described in "Poor Flotation".
Excessive Vibration
1. Disconnect from the mains electricity supply.
2. Check that the blade is fitted correctly?
3. If the blade is damaged or worn, replace it with a new one.
4. If vibration persists?
Immediately disconnect from the mains electricity supply and consult your local approved Service Centre.
Service Recommendations
1. We strongly recommend that your product is serviced at
least every twelve months, more often in a professional
application.
2. Always use genuine Flymo Spare Parts.
3. Prepacked spares are available from most Electrolux
Outdoor Products stockists.
4. Your product is uniquely identified by a silver and black
product rating label
5. If you have a problem with your machine contact your
local Approved Service Centre ensuring you have full
details of your product as described on the product rating
label.
6. Should it be necessary for work to be carried out by
your Service Centre, it is important to take your complete machine including cable and any extension
cables used.
A network of specialist dealers can be found in your local
Yellow Pages.
To obtain service on your Flymo product simply telephone or
visit your local Service Centre.
Should you require service under the terms of our guarantee
the Service Centre will require proof of purchase.
All of the centres listed stock genuine Flymo Spare Parts.
NOTE: Our Service Repairers act on their own behalf and
are not empowered to commit or legally bind Electrolux
Outdoor Products in any manner whatsoever.
Guarantee & Guarantee Policy
If any part is found to be defective due to faulty manufacture
within the guarantee period, Electrolux Outdoor Products,
through its Authorised Service Repairers will effect the
repair or replacement to the customer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken
apart or tampered with by any person not authorised by
Electrolux Outdoor Products.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used outside of the country
for which it was specified.
(i)
The machine has not been used commercially.
*
This guarantee is additional to, and in no way diminishes the customers statutory rights.
Failures due to the following are not covered, therefore it is
important that you read the instructions contained in this
Operator's Manual and understand how to operate and
maintain your machine:
Failures not covered by guarantee
*
Replacing worn or damaged blades
*
Failures as a result of not reporting an initial fault.
*
Failures as a result of sudden impact.
*
Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual.
*
Machines used for hire are not covered by this guarantee.
*
The following items listed are considered as wearing
parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid
warranty claim: Blades, Electric Mains cable.
*
Caution!
Electrolux Outdoor Products does not accept liability
under the warranty for defects caused in whole or part,
directly or indirectly by the fitting of replacement parts
or additional parts that are not either manufactured or
approved by Electrolux Outdoor Products, or by the
machine having been modified in any way
Environmental Information
Electrolux Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where
practical, components manufactured in the most environmentally responsible manner, according to company procedures,
and with the potential for recycling at the end of the products’ life.
•
Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling.
•
Awareness of the environment must be considered when disposing of ‘end-of-life’ product.
•
If necessary, contact your local authority for disposal information.
EC Declaration of Conformity
I, the undersigned M. Bowden of Electrolux
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP. Certify that the Lawnmower:Category........ Electric Hover
Make..........Electrolux Outdoor Products
Conforms to the specifications of Directive
2000/14/EEC
I, the undersigned M. Bowden of Electrolux
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP Certify that a sample of the above
product has been tested using directive
81/1051/EEC as a guide. The maximum Aweighted sound pressure level recorded at
operator position under free field semi anechoic chamber conditions was :-
Type of Cutting Device.... Rotary Blade
Identification of Series......See Product Rating Label
Conformity Assesment Procedure....ANNEX VI
Notified Body.................... I.T.S.. Cleeve Road, Leatherhead,
Surrey, KT22 7SB. England
Other Directives:-............. 98/37/EEC, 89/336/EEC, 73/23/EEC
& applicable standards:-. EN60555-2:1987, EN60555-3:1987,
EN55014:1993, EN55014:1995, EN836:1997, IEC335-1:1991,
IEC335-2-77:1996
I, the undersigned M. Bowden of Electrolux
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP Certify that a sample of the above
product has been tested using ISO 5349 as
a guide. The maximum weighted root mean
square value of vibration recorded at operator’s hand position was:-
Type..................................................... Micro Compact 300 plus
Width of Cut..........................................30 cm
Speed of Rotation of Cutting Device.... 5,300 RPM
Guaranteed sound power level............ 96 dB (A)
Measured Sound Power Level............. 93 dB (A)
Level..................................................... 82 dB(A)
Value.....................................................1.81 m/s2
Weight...................................................8.5 kg
Electrolux Outdoor Products
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co.Durham DL5 6UP
ENGLAND
Telephone - (00) 44 1325 300303 Fax - (00) 44 1325 310339
Newton Aycliffe, 10/1/2003
M. Bowden,
Research & Development Director
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior
notice. Electrolux Outdoor Products manufacture products for a number of well known brands under various registered
patents, designs and trademarks in several countries.
© Electrolux Outdoor Products Ltd. Registered Office, Electrolux Works, Oakley Road, Luton LU4 9QQ
Registered number 974979 England
The Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than
55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and
lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
5118144-06
">