Electrolux EDI97170W User Manual
إعلان
إعلان
user manual
Iron AidTM
EDI97170W
2
electrolux
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
CONTENTS
Important safety information
Environment
Product description
Control panel
What is shown in the display
Before first use
Sorting and preparing laundry
Starting up for the first time
Iron AidTM Steam System
Starting an Iron AidTM programme
6
6
7
7
2
4
5
6
8
12
Drying
Starting a drying programme
Drying rack
Cleaning and maintenance
What to do if ...
Technical data
Machine settings
Hints for test institutes
Installation
Service
Subject to change without notice
14
16
17
18
21
23
24
24
25
27
IMPORTANT SAFETY INFORMATION
Important!
Only operate the Iron Aid programmes with distilled water!
Mains water causes damage to the appliance.
Important!
In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety.
- Please read the instruction book before using this appliance.
General safety
• It is dangerous to alter the specifications or attempt to modify this product in any way.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Make sure that small pets do not climb into the drum. To avoid this, please check into the drum before using.
• Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp material can cause extensive damage and must not be placed into the machine.
• In order to avoid danger of fires caused by excessive drying, do not use appliance to dry the following items: cushions, quilts and the like (these items accumulate heat).
• Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer.
• Always unplug the appliance after use, clean and maintenance.
• Under no circumstances should you attempt to repair the machine yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local Service Centre. Always insist on genuine spare parts.
• Items that have been soiled with substances such as cooking oil acetone, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer.
•
Danger of explosion:
never tumble dry items that have been in contact with in-
electrolux
3
flammable solvents (petrol, methylated spirits, dry cleaning fluid and the like). As these substance are volatile, they could cause an explosion. Only tumble dry items washed with water.
•
Risk of fire:
items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be placed in the tumble dryer.
• If you have washed your laundry with stain remover you must execute an extra rinse cycle before loading your tumble dryer.
• Please make sure that no gas lighters or matches have accidentally been left in pockets of garments to be loaded into appliance
• When removing from the socket, never pull the mains plug by the cable, instead take a hold of the plug.
• The height adjustable screw feet must never be removed.
• Manifold plugs, couplings and extension cables must not be used. Risk of fire from overheating!
• Do not spray down the appliance with jets of water. Risk of electric shock!
• Do not lean on the open door. The appliance may tip over.
• Once the drying cycle or Iron Aid programme has been interrupted, the laundry and drum may be hot. Risk of burns!
Take care when removing the laundry.
• Take care when interrupting the Iron Aid programme: Do not open the machine door during the steam phase. Hot steam may result in burns. The display shows a message to indicate the steam phase.
• The final part of a drying cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged.
•
Caution – Hot surface:
Do not touch the back of the appliance while it is operating.
Warning!
Never stop a tumble dry before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. Risk of fire!
•
Risk of electric shock!
Do not spray down the appliance with jets of water.
Installation
• This appliance is heavy. Care should be taken when moving it.
• When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the Service Centre.
• All packaging must be removed before use. Serious damage can occur to the product and to property if this is not adhered to. See relevant section in the user manual.
• The final part of a tumble dryer cycle occurs without heat ( cool down cycle ) to ensure that the items are left at a temperature that ensures that items will not be damaged.
• Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
• Care must be taken to ensure that the appliance does not stand on the electrical supply cable.
• If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely under the appliance.
• After having installed the appliance, check that it is not pressing or standing on its electrical supply cable.
• If the tumble dryer is placed on top of a washing machine, it is compulsory to use the stacking kit (optional accessory).
Use
• The appliance is intended for drying and steam treatment of standard laundry in domestic applications.
• This appliance is designed for domestic use. It must not be used for purposes other than those for which it was designed.
• Only dry fabrics which are designed to be machine dried. Follow the instructions on each garment label.
• Do not dry unwashed items in the tumble dryer.
• Do not overload the appliance. See the relevant section in the user manual.
• Clothes which are dripping wet should not be placed in the dryer.
• Garments which have been in contact with volatile petroleum products should not be machine dried. If volatile cleaning fluids are used, care should be taken to
4
electrolux ensure that the fluid is removed from the garment before placing in the machine.
• When using dry-cleaning sets: only use those products which are declared as suitable for the dryer by the manufacturer.
• Clean the micro-fine filter and fine strainer after each drying cycle or Iron Aid programme.
• Do not use the machine without a lint filter or with a damaged lint filter. Risk of fire!
• Only fill the water reservoir for steam treatment with distilled water. Do not use tap water or any additives! The condensed water from this appliance’s condensed water container can also be used, if it is filtered first (e. g. with a coffee filter).
• Clean the heat exchanger regularly.
• Never pull the power supply cable to remove the plug from the socket; always take hold of the plug itself.
• Never use the tumble dryer if the power supply cable, the control panel, the working surface or the base are damaged so that the inside of the tumble dryer is accessible.
• With stacked washer and Iron Aid appliance: do not place objects on the appliance. These may fall off during operation.
ENVIRONMENT
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.
Old appliance
Warning!
Remove mains plug from socket when you have no further use for the machine. Cut off mains cable and dispose of together with
• The lamp cover for the interior light must be screwed down tightly.
• Fabric softeners, or similar products should be used as specified by the fabric softener instructions.
•
Caution - hot surface
: Do not touch the door light cover surface when the light is switched on.
Child safety
• This machine is not intended for use by young children or infirm persons without supervision.
• Children should be supervised to ensure that they do not play with the appliance.
• The packaging components (e.g. plastic film, polystyrene) can be dangerous to children - danger of suffocation! Keep them out of children’s reach.
• Keep all detergents in a safe place out of children’s reach.
• Make sure that children or pets do not climb into the drum.
plug. Destroy loading door hook. Children cannot then lock themselves in the machine and put their lives at risk.
Packaging material
The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g.
>PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities.
Environmental tips
• In the dryer, laundry becomes fluffy and soft. Fabric softeners are not therefore needed when washing.
• Your dryer will function most economically if you:
– always keep the ventilation slots on the base of the dryer unobstructed;
– use the loading volumes specified in the programme overview;
– ensure you have good ventilation in the installation room;
– clean the micro-fine filter and fine strainer after each drying cycle;
– spin the laundry well before drying.
PRODUCT DESCRIPTION
electrolux
5
Energy consumption depends on spinning speed set in washing machine.
Higher spinning speed - lower energy consumption.
6
7
8
9
10
11
12
13
14
1 Control panel
2 Fluff filters
3 Loading door (reversible)
4 Ventilation grille
5 Adjustable feet
6 Water recirculation valve/filter, Filler neck for steam water tank
7 Drawer with condensed water container
8 Drum light
9 Drying rack
10 Push button for base door opening
11 Rating Plate
12 Heat exchanger
13 Drainage hose for water tank
14 Heat exchanger door
3
4
5
1
2
6
electrolux
CONTROL PANEL
1 2 3 4
1 Programme knob and On/Off switch
2 Display
3 DELAY TIMER button
4 Maintenance displays
– HEAT EXCHANGER
5
– FILTER
– CONTAINER
5 Function buttons
6 START/PAUSE button
6
WHAT IS SHOWN IN THE DISPLAY
1 2 3 4 5 6 7 8
1 LOAD
2 DRYNESS
3 Start time preselection
4 Drying
5 Iron Aid programme
6 Cooling
7 Anticrease
BEFORE FIRST USE
In order to remove any residues which may have been produced during production, wipe the dryer drum with a damp cloth or carry out a brief drying cycle (30 MIN) with damp cloths in the machine.
9 10 11 12 13 14
8 Degree of dryness Display
9 DELICATE
10 Child safety device
11 Steam water tank indicator
12 BUZZER
13 Steam display
14 Start time /programme duration display
1. Turn the programme knob to
TIME .
2. Press the TIME button repeatedly until
0.30 appears in the display.
3. Press the START/PAUSE button.
electrolux
7
SORTING AND PREPARING LAUNDRY
Sorting laundry
• Sort by fabric type:
– Cotton/linen for programmes in
COTTONS programme group.
– Mixed fibres and synthetics for programmes in the SYNTHETICS programme group.
• Sorting by care label. The care labels mean:
Drying in the tumble dryer possible in principle
• Do not dry new, coloured textiles together with light-coloured laundry items. Textile colours may bleed.
• Do not dry cotton jersey and knitwear with the EXTRA programme. Items may shrink!
• Wool and wool-like textiles can be dried using the WOOL programme. Before the drying cycle spin the woollen textiles as well as possible (max. 1200 rpm). Only dry woollen textiles together which are similar or the same with respect to material, colour and weight. Please dry heavy laundry items made of wool separately.
Special notes about Iron Aid
Caution!
Dry at normal temperature
Important!
Do not place in the appliance any wet laundry which is not specified on the care label as being suitable for tumbledrying.
This appliance can be used for all wet laundry items which are labelled as suitable for tumble-drying.
• The following textiles cannot be treated using an Iron Aid programme: woollen knitwear, leather, textiles with large metal, wooden or plastic parts, textiles with rusting metal parts, oilskins or wax cotton garments.
• To smooth or freshen laundry with an
Iron Aid programme, sort laundry by size,
Dry at reduced temperature (press DELICATE button!)
Drying in the tumble dryer
not
possible weight, material and colour. Only smooth textiles together that are similar in terms of size, weight, material and colour.
• Do not dry new, coloured textiles together with light-coloured laundry items. Colours may fade (check colour fastness of fabric when damp in an inconspicuous area).
• Do not use dry cleaning sets such as dryel in combination with Iron Aid programmes.
Preparing laundry
• To avoid laundry becoming tangled: close zips, button up duvet covers and tie loose ties or ribbons (e.g. of aprons).
• Empty pockets. Remove metal items (paper clips, safety pins, etc).
• Turn items with double-layered fabrics inside out (e.g. with cotton-lined anoraks, the cotton layer should be outermost).
These fabrics will then dry better.
Special notes about Iron Aid
• Before treating garments with an Iron Aid programme, remove stains by washing or using localised stain removal.
• Turn items with double-layered fabrics inside out (e.g. with cottonlined anoraks, the cotton layer should be outermost).
These fabrics will then dry better.
STARTING UP FOR THE FIRST TIME
Switching appliance on / switching light on.
Turn the programme selector to any programme. The appliance has been switched on. When the loading door is opened, the drum is illuminated. Opening loading door / loading laundry
1. Open loading door: Push against the loading door (push point )
8
electrolux
2. Load your laundry (do not force it in/ overload the machine).
Caution!
Be careful not to trap laundry in between the loading door and rubber seal.
3. Close loading door securely. Lock must audibly lock.
IRON AID
TM
STEAM SYSTEM
Fill water tank
You must fill up the water tank before using an Iron Aid programme for the first time.
Use the distilled water provided if there is not yet any condensed water from previous drying programmes (see chapter on "Cleaning and Maintenance, Emptying condensed water container"). If, after an Iron Aid programme is selected, the water tank indicator on the display lights up, you will need to fill up the water tank with distilled water. Otherwise, you will not be able to start any Iron Aid programme.
Caution!
Important! Only fill the water tank with distilled or fully desalinated water. Do not use tap water or additives! You can also use the condensed water from the tank, as long as you filter it first (use the canister supplied with the filter fitted: see figure opposite).
1. Pull drawer containing condensed water container out a little (1),
1
2. Push down the water tank’s filler neck
(1) and pull out it (2).
1
2
3. Fill with distilled water from the canister provided, up to the MAX mark inside the container.
electrolux
9
To activate recirculation set valve to the ON position. To do that:
1. Pull drawer containing condensed water container out a little (1). Behind the drawer there is water tank’s filler neck (2).
max
2
4. Push filler neck and drawer with condensed water container back in.
When dry, all textiles not specifically prohibited in the chapter ‘Sorting and preparing laundry’ may be treated with the Iron Aid
Steam System. Wet textiles may only be treated if they are labelled as suitable for dry programmes.
Water recirculation system
This system allows you to automatically use for an Iron Aid Steam cycle the condensed water collected in the condense water tank during a drying cycle.
Caution!
The water in the condense water tank will never automatically fill the steam water tank. The water recirculation system works only if it is supplied by water arising during standard drying cycles.
To activate this system turn the valve to the
ON position. When the valve is ON the steam water tank will be filled during the next drying cycle. Water will be supplied by the water circuit directly to the steam water tank filling it automatically.
Overview of Iron Aid programmes
Additional functions / options
Programmes
1
2. Turn the valve to the ON position. Water will be supplied by the water circuit directly to the steam water tank filling it automatically during the next drying cycle.
The steam water tank is empty. Please fill it and then press START/PAUSE
If valve is closed (OFF position) recirculation system does not work.
Application/properties
COTTON
1.0 kg • •
For 1- 6 cotton shirts. Min. 80% natural fibres (cotton, linen etc).
wet, dry
10
electrolux
Additional functions / options
Programmes Application/properties
SYNTHETICS
COTTON
SYNTHETICS
REFRESH
1.0 kg
3.0 kg
1.5 kg
2.5 kg
•
•
•
•
•
•
•
•
All information on applications is for guidance only. Smoothing results may vary depending on the selected programme and especially the fittings and material properties of the textile. The results can be improved if necessary by using different programmes and steam volumes. For example, some textiles containing more than 20% synthetics but with the right fittings may behave more like cotton textiles in an
Iron Aid programme. You may therefore get better smoothing results by selecting a cotton Iron Aid programme.
Given the wide range of different textile grades and properties that can be manufactured today using different mechanical and chemical processes, we recommend running the first few Iron Aid programmes at low steam levels and with a small number of garments that are as similar as possible. Later, you can carefully start to vary the conditions of Iron Aid programmes to learn from experience how to get the best results from the volume of laundry loaded, the quality of the textiles and the most suitable steam levels and Iron Aid
TM
programmes. Please also note the accompanying ‘Textile Guide’.
For 1- 6 synthetic shirts. Max. 20% natural fibres (cotton, linen etc).
For smoothing cotton garments. Min.
80% natural fibres (cotton, linen etc).
For smoothing easy-care garments.
Max. 20% natural fibres (cotton, linen etc).
For one suit or up to two suit jackets or pairs of trousers or similar garments. Also suitable for removing odours. For dry garments only wet, dry wet, dry wet, dry
electrolux
11
Programme LOAD Loading volume
DURATION dry [min.]
1)
DURATION wet [min.]
1)
COTTON
MIN
MED
MAX
1 - 2 shirts
3 - 4 shirts
5 - 6 shirts
20-23 41-51
SYNTHETICS
MIN
MED
MAX
1 - 2 shirts
3 - 4 shirts
5 - 6shirts
14-17 24-49
COTTON
MIN
MED
MAX
0.5 - 1 kg
1 - 2 kg
2 - 3 kg
13-16 53-64
SYNTHETICS
MIN
MED
MAX
0.2 - 0.5 kg
0.5 - 1 kg
1 - 1.5 kg
12-16 43-53
REFRESH
MIN
MED
MAX
1 pair of trousers
1 jacket
1 suit
12-16
1) exact programme times appear in the display once the machine has performed wet/dry recognition (approx. 2 min.)
All information provided on selecting the steam level and corresponding load are suggestions only. In some cases, using a higher steam level or smaller load may give better results. The REFRESH programme is a gentle Iron Aid programme for nonwashable textiles.
Any distortion to the shape of a garment which might occur in few cases, can be remedied by ironing.
Selecting the programme
Use the programme selector to set the programme you require. The estimated programme duration (in minutes) appears in the multi-display.
Select steam level LOAD (LOAD)
To achieve the best results, different steam levels are required for different volumes of laundry.
The LOAD button is used to set the required steam level: MIN , MED or MAX .
All Iron Aid programmes, apart from the
REFRESH programme, automatically recognise the remaining dampness in clothes.
When laundry is wet, a drying cycle is activated first if required.
The table shows the steam levels appropriate for the selected load, under LOAD .
1. Press the LOAD button repeatedly until the desired steam level ( MIN , MED or
MAX ) is shown in the display.
If the LOAD button is not pressed after an
Iron Aid programme is selected, then medium steam level ( MED ) is selected automatically. If you select the REFRESH programme, MIN is selected automatically.
12
electrolux
Important: If in doubt, always select a lower steam level first until you have more experience with load volumes, fabric types and the corresponding optimum steam level. If too high a steam level is selected, garments may lose their shape. If too low a steam level is selected, creases may remain.
Selecting additional functions
The additional functions available for the
Iron Aid programmes are BUZZER (BUZ-
ZER), DELAY (DELAY) and the CHILD LOCK.
BUZZER (BUZZER)
The appliance is supplied with the BUZZER
function activated. When the drying cycle has finished, an intermittent acoustic signal will sound. Each time a button is pressed or a programme is changed using the programme knob, an audible signal is also set to sound. The button is used to switch the function on or off. When the function is active, the BUZZER symbol appears in the display.
DELAY (DELAY)
With the DELAY button, you can delay the start of a programme by between
30 minutes ( ) and a maximum of 20 hours (
).
1. Select the programme and additional functions.
2. Press the DELAY button as many times as necessary until the required start delay appears on the display, e.g.
if the programme is to be started in 12 hours.
3. To activate the delay timer, press the
START/PAUSE button. The amount of time remaining until the programme is set to start is continuously displayed
(e.g. , ,
, … etc).
If the display is showing
and you press the button again, the time delay will be cancelled. The display will show and then the duration of the selected programme.
CHILD LOCK
The child lock can be set to prevent a programme being accidentally started or a programme in operation being accidentally changed. The child safety device locks all buttons and the programme knob. The child safety device can be activated or deactivated by holding down the BUZZER and
TIME buttons simultaneously for 5 seconds.
• Before programme is started: Appliance cannot be used
• After programme is started: Programme in operation cannot be changed
The symbol appears in the display to indicate that the child safety device is activated. The child safety device is not deactivated once the programme comes to an end.
If you want to set a new programme, you must first deactivate the child safety device.
STARTING AN IRON AID
TM
PROGRAMME
Press the START/PAUSE button. The programme is started. First, the drying phase indicator appears in the display. The display will also show the programme duration for the selected Iron Aid programme, not including the additional drying phase. With wet laundry, after a few minutes the appliance will show the correct programme duration for the Iron Aid programme including the preceding drying programme. As soon as the right level of dryness is reached, the Iron
Aid programme will start automatically. The steam indicator shows the progress of the
Iron Aid programme in the display. The individual steam phases are shown by animated clouds of steam.
electrolux
13
Caution!
Important: During the steam phases that form part of the Iron Aid programme and also the anti-crease phase (represented by animated clouds of steam in the display), the loading door cannot be opened. Risk of burns!
If the water tank indicator lights up when you select an Iron Aid programme, the programme cannot be started. You will need to fill the water tank first (see section on ‘Cleaning and maintenance,filling water tank’.)
It is normal for the appliance to make noises during an Iron Aid or drying programme if garments with hard parts, such as metal buttons, are put in the drum.
Changing a programme
To change a programme which has been selected by mistake once the programme has started, first turn the programme selector to
O
OFF and then reset the programme.
The programme can no longer be changed directly once the programme has started. If you nevertheless attempt to change the programme with the programme knob or an additional function button (except the BUZZER button), the START/PAUSE button and will flash in the display. The drying programme is not however affected by this.
Putting in extra items or taking items out before end of programme
1. Open door.
2. Load or remove laundry items.
3. Close door securely.
4. Press the START/PAUSE button to continue the drying cycle.
Iron Aid programme complete / removing laundry
After the Iron Aid phase has ended,
is illuminated and the icon AN-
TICREASE appears in the display. If the
BUZZER has been activated, an audible signal sounds at regular intervals.
The Iron Aid programme is automatically followed by an anti-crease phase, including brief steam phases, which lasts around 90 minutes.
The drum rotates during the anti-crease phase. This keeps the laundry loose and free of creases. It can be removed at any point during the anti-crease phase, except during steam phases (look for steam animation in the display!). Laundry should be removed as quickly as possible.
1. Open the loading door to remove the laundry.
2. Before removing the laundry, remove fluff from the micro-fine filter. It is best to use a damp hand for this purpose. (See
“Cleaning and maintenance” section.)
3. Remove laundry one garment at a time.
4. Turn the programme knob to
O
OFF .
Important! After each drying cycle
– Clean the micro-fine filter and fine filter
– Drain the condensed water container
(See section “Cleaning and maintenance”.)
5. Close door.
Caution!
To retain the effects of the
Iron Aid treatment, clothes must be removed one garment at a time during the anticrease phase and hung immediately on a clothes hanger to dry (for at least 5-15 mins, depending on fabric and selected steam level). Do up the buttons and tug the garment into shape, paying particular attention to cuffs and seams.
14
electrolux
DRYING
Overview of drying programmes
Programmes Additional functions / options
Application/properties
EXTRA
DAMP
7 kg • • • -
CUPBOARD
7 kg • • • -
7 kg • • • -
COTTON
Thorough drying of thick or multilayered fabrics, e.g.
terry towelling items, bathrobes.
Thorough drying of fabrics of even thicknesses, e.g.
terry towelling items, knitwear, towels.
For normal thickness cotton or linen laundry, e.g.
bedding, table linen .
SYNTHETICS
EXTRA
3 kg • • • -
Thorough drying of thick or multilayered fabrics, e.g.
pullovers, bedding, table linen.
1)
CUPBOARD
3 kg • • • -
For thin fabrics which are not ironed e.g. easy care shirts, table linen, baby clothes, socks, lingerie with bones or wires.
1)
DAMP
TIME
SILK
3 kg • • • -
For thin textiles which are still to be ironed, e.g. knitted items, shirts.
1)
7 kg • • •
SPECIA L
For further drying of individual items of laundry or for small volumes of less than 1kg. You can select a programme duration from 10 mins to 3 hrs in 10-minute steps.
1 kg • t o a u
• -
Special programme for drying silk using warm air and gentle movement. .
electrolux
15
Programmes Additional functions / options
Application/properties
WOOL &
SPORT SHOES
1 kg • a u t o
•
For drying woollen fabrics after they have been washed, using warm air at minimum mechanical load (Follow section “Sorting and preparing washing”). Recommendation: Remove fabrics immediately after drying, as no anticrease programme follows.
For gentle drying of one pair of sport shoes, washed and spindried at 1000 rpm.
You can select a programme duration from 30 mins to 3 hrs in 10-minute steps.
1) Press the DELICATE button.
Selecting the programme
Use the programme selector to set the programme you require. The estimated programme duration (in minutes) appears in the multi-display.
DRYNESS (DRYNESS)
Selecting additional functions
You can choose from the additional functions DRYNESS (DRYNESS), DELICATE
(DELICATE), BUZZER (BUZZER) and TIME
(TIME ), (if a TIME programme has been selected). The symbols of the functions available for the selected programme are shown in the display.
If laundry comes out of the machine too damp after a standard drying programme, you can increase the drying result by using the DRYNESS function. Laundry becomes drier as you move from MIN to MAX.
1. Press the DRYNESS button repeatedly until the desired dryness level ( MIN ,
MED or MAX ) is shown in the display. If another programme has been selected,
AUTO flashes in the display.
If wool or silk comes out of the machine too damp at the end of a WOOL or
SILK programme, you can dry it again by restarting the appropriate programme, this time with the DRYNESS function selected and dryness level MIN , MED or MAX . In the case of a drying cycle with relatively dry laundry, the length of the programme cycle displayed at the beginning is corrected after a while.
16
electrolux
Caution!
Caution: Make sure that by selecting the DRYNESS function, you do not over-dry your wool or silk.
DELICATE (DELICATE)
For especially gentle drying of sensitive fabrics with the care label and for temperaturesensitive textiles (e.g. acrylic, viscose). Programme is executed with reduced heat.
DELICATE is only suitable for use with loads of up to 3kg.
1. Press the DELICATE button. The
DEL-
ICATE symbol appears in the display.
TIME (TIME)
To select the programme duration after setting the TIME programme. You can select a programme duration from 10 minutes to 3 hours in 10-minute steps. (corresponding to the COOLING (COOLING) programme).
1. Turn the programme knob to the
TIMED PROGRAMME. The
minutes is in the display
2. Press the TIME button repeatedly until the desired programme duration is shown in the display, e.g.
for a programme of 20 minutes.
If the programme duration is not selected, the duration is automatically set to 10 mins.
BUZZER (BUZZER)
See chapter "Iron AidTM Steam System" , section "Selecting additional functions -
BUZZER "
DELAY (DELAY)
See chapter "Iron AidTM Steam System" , section "Selecting additional functions - DE-
LAY "
CHILD LOCK
See chapter "Iron AidTM Steam System" , section "Selecting additional functions -
CHILD LOCK"
STARTING A DRYING PROGRAMME
Press the START/PAUSE button. The programme is started. The programme progress display shows drying progress. The symbols for DRYING and COOLING appear in the display one after the other.
The number of droplets in the dryness indicator gradually goes down as the drying process progresses.
Changing a programme
To change a programme which has been selected by mistake once the programme has started, first turn the programme selector to
O
off
and then reset the programme.
The programme can no longer be changed directly once the programme has started. If you nevertheless attempt to change the programme with the programme knob or an additional function button (except the BUZZER button), the START/PAUSE button and will flash in the multi-display. The drying programme is not however affected by this.
Removing laundry or loading laundry when necessary
Warning!
Laundry and drumcan become hot. Risk of burns!
1. Open loading door
2. Load or remove laundry items.
3. Close the door securely. Lock must audibly lock.
4. Press the START/PAUSE button to continue the drying cycle.
Drying cycle complete / removing laundry
Once the drying programme has finished,
CREASE GUARD lights up in the display. If the BUZZER is activated, an audible signal sounds at regular intervals.
The drying cycle is automatically followed by a anti-crease phase which lasts around 30 minutes.
The drum rotates at intervals during this phase. This keeps the laundry loose and free of creases. It can be removed at any time during the anti-crease phase. (The laundry should be taken out towards the end of
electrolux
17
the anti-crease phase at the latest to prevent creases from forming.)
1. Open door.
2. Before removing the laundry, remove fluff from the micro-fine filter. It is best to use a damp hand for this purpose. (See
“Cleaning and maintenance” section.)
3. Remove laundry.
DRYING RACK
Special equipment for gentle drying washable woollens and sport shoes. Incomparable for drying wet woollens - eliminated movement, protection from matting.
For drying rack unpacking see
Installation
chapter.
Important!
Before drying rack installation check the dryer drum.
It must be empty!
Sport shoes cannot be dry without the drying rack - drum damage.
Installation and use
1. Open the loading door.
2. Insert the rack carefully resting its two support brackets on the front of plastic flange.
4. Turn the programme knob to
O
off.
5. Important! After each drying cycle
– Clean the micro-fine filter and fine filter
– Drain the condensed water container
(See section “Cleaning and maintenance”.)
6. Close door.
3. Place the woollens or pair of sport shoes on the rack.
4. Select the suitable rack drying programme and drying time.
5. Press the START/PAUSE button.
6. When cycle is finished open the loading door and remove the woollens or shoes.
7. Turn the programme selector to OFF.
8. Take out the drying rack of the drum.
Drying tips
• for the best drying result spread the woollens out loosely on the drying rack and roll it up
• do not squash and fold the woollens
• open support and put sport shoes on it
18
electrolux
• the insoles should be placed beside the shoes on the drying rack and the shoelaces should be tied
CLEANING AND MAINTENANCE
Cleaning lint filters
To ensure that the appliance works perfectly, the lint filters in the door and in front of the drum must be cleaned after every Iron
Aid
TM
or drying cycle.
Caution!
Important. Never operate the dryer without the lint filter or with a damaged or blocked lint filter.
1. Open loading door
4. Remove fluff from lint filter, preferably using a damp hand for this purpose.
5. Replace the filter.
2. Use a damp hand to clean the microfine filter, which is built into the lower part of the loading aperture.
3. After a period of time, a patina due to detergent residue on laundry forms on the filters. When this occurs, clean the filters with warm water using a brush. Remove the filter from the door pulling it out. It can be positioned with the tooth facing to the left or to the right). After cleaning do not forget to put it back.
Cleaning the water recirculation valve/ filter
Caution!
Remove and clean Steam
Water Filter every 6 months
The valve/filter is placed behind the tank handle - see chapter "Product description".
1. Push down the water tank’s filler neck
(1) and pull out it (2).
1
2
2. Clean the valve/filter under warm water.
electrolux
19
Emptying the condensed water container
Empty condensed water container after every drying cycle. If the condensed water container is full, an active programme will break off automatically and the icon display will light up. In order to continue the programme, the condensed water container must first be emptied.
Warning!
The condensed water is not suitable for drinking or for preparing foodstuffs.
1. Pull drawer containing condensed water container all the way out (1) and pull up the condensed water container’s drainage pipe as far as it will go (2).
2.
3. Re-insert the valve/filter.
4. Turn the valve/filter in ON position.
1.
2. Pour out the condensed water into a basin or similar container.
3. Push drainage pipe in and refit condensed water container.
Clean the door seal
Wipe the door seal using a damp cloth immediately after the Iron Aid or drying cycle.
If the programme has been interrupted as a result of the condensed water container being full: Press the START/
PAUSE button to continue the drying cycle.
20
electrolux
The condensed water container has a volume of approx. 4 litres. This is sufficient for around 7 kg of laundry which has previously been spun at 1000 revolutions/ minute.
4. The condensed water can be used as distilled water, e.g. for steam irons. However, first filter the condensed water to remove any residues and small pieces of fluff.
3. Clean fluff from the inside of the door and the heat exchanger front chamber.
Wipe the door seal with a damp cloth.
4. Turn both lock washers inwards.
Using the attached canister to filter:
Pour the water out of the container straight through the filter at the top of the canister.
Cleaning heat exchanger
If the HEAT EXCHANGER is displayed, the heat exchanger needs to be cleaned.
Caution!
Operating when the heat exchanger is blocked with fluff can damage the dryer. This also increases energy consumption.
1. Open door.
2. Open door in plinth. To do this, press the release button on the bottom of the door aperture and open the door in the plinth to the left.
5. Use the handle to pull the heat exchanger out of the base and carry it horizontally to prevent any remaining water from spilling.
6. To empty the heat exchanger, hold vertically over a washing-up bowl.
Caution!
Do not use sharp objects to clean. The heat exchanger could develop leaks.
7. Clean heat exchanger.
electrolux
21
It is best to use a brush or to rinse thoroughly with a hand-held shower.
8. Replace heat exchanger and lock into place (turn both lock washers outwards until they snap into place).
9. Close door in plinth.
The appliance will not operate if the
HEAT EXCHANGER indicator is still lit.
Caution!
Never operate the dryer without the heat exchanger.
Cleaning the drum
Caution!
Do not use abrasives or steel wool to clean the drum.
Lime in the water or cleaning agents may form a barely visible lining on the inside of the drum. The degree to which the laundry has been dried is then no longer detected reliably. The laundry is damper than expected when removed from the appliance.
Use a standard domestic cleaner (e.g. vinegar-based cleaner) to wipe down the inside of the drum and drum ribs.
Clean control panel and housing
Caution!
Do not use furniture cleaners or aggressive cleaning agents to clean the machine.
Use a damp cloth to wipe down the control panel and housing.
WHAT TO DO IF ...
Troubleshooting by yourself
If during operation, the error code E plus number or letter) appears on the multi-display: Switch the appliance off and on again.
Problem Possible cause
Reset programme. Press the START/
PAUSE button. If the error appears again, please contact the Customer Care Department, stating the error code
Dryer does not work.
Mains plug is not plugged in or fuse is not working correctly.
Loading door is open.
Have you pressed the START/
PAUSE button?
Remedy
Plug in at mains socket. Check fuse in fuse box (domestic installation).
Close loading door.
Press the START/PAUSE button again.
IronAid programme does not start. the water tank indicator lights up.
Water tank is empty.
Fill water tank.
Turn the recirculation valve to ON position.
After a IronAid programme, garments are not sufficiently smooth.
Recirculation valve is closed (OFF position)
Wrong programme selected
(e.g. SYNTHETICS instead of COTTON ).
Too low a LOAD level set.
Too many garments in machine, or garments that are too different.
Note the composition of the fabric.
Clothes are not removed until the anti-crease phase is finished.
Garments not hung on clothes hangers and/or not tugged into shape.
Set a higher LOAD level.
Load the machine with fewer garments, or only similar ones.
Remove clothes quickly one at a time from the machine as soon as possible after the start of the anticrease phase.
Hang garments on clothes hangers, do up buttons and tug garments into shape.
22
electrolux
Multi-layered garments tend to lose their shape.
Reshape multi-layered garments by ironing after they come out of the machine.
After a IronAid programme, there are no creases left in the garments.
The IronAid programme has the effect of smoothing garments.
Iron creases in again after the Iron-
Aid programme.
Drying results unsatisfactory.
When a button is pressed
- no reaction of the machine.
Drum light does not work.
Displayed programme time changes erratically or stays unchanged for a long time.
Programme inactive,
CONTAINER display illuminated.
Drying cycle ends shortly after programme starts. ANTICREASE display illuminated.
Drying cycle lasts an unusually long time. Note:
After up to 5 hours the drying cycle ends automatically (see ‘End of drying cycle’).
Wrong programme selected.
Select a different programme the next time you dry (see “Programme overview” chapter).
Lint filters clogged.
Fluff filter clogged.
Clean lint filters.
Clean fluff filter.
Heat exchanger clogged with lint.
Clean heat exchanger.
Overloading of laundry.
Ventilation slots in base area covered up.
Residue on inside surface of drum or drum ribs.
Conductance of water at installation site differs from standard setting of machine.
Drying protection. After the start of the programme, the option can no longer be set.
Programme selector in OFF position.
Defective light bulb.
Observe recommended loading volumes.
Uncover ventilation slots in base area.
Clean inside surface of drum and drum ribs.
Make an adjustment using the
DRYNESS function (see chapter ”Drying”)
Re-programme standard setting for degree of drying (see ‘Programming options’ chapter).
Turn the programme knob to
OFF . Set the programme again.
Turn programme selector to any programme.
Replace light bulb (see next section).
Programme time is corrected automatically depending on type and volume of laundry and level of dampness.
Automatic process; this is not a machine fault.
Condensed water container is full.
Empty Condensed water container , then start programme with
START/PAUSE button.
Not enough washing loaded or washing loaded is too dry for selected programme.
Lint filter clogged.
Fluff filter clogged.
Load volume too big.
Select time programme or higher drying level (e.g. EXTRA instead of CUPBOARD ).
Clean lint filter.
Clean fluff filter.
Reduce load volume.
electrolux
23
Discoloration
Laundry insufficiently spun.
Particularly high room temperature. Temporary switching off of the compressor to avoid overload.
Changing the bulb for interior lighting
Only use a special bulb which is designed specially for dryers. The special bulb can be obtained from your local Service Force centre.
Warning!
When the appliance is switched on, the interior lighting switches itself off after 4 minutes when the door is open.
Colour fastness of textiles.
Laundry must be adequately spun.
Automatic process, there is no fault with the appliance. If possible, lower the room temperature.
Check colour fastness of textiles.
Only treat textiles together if they are a similar colour.
1. Unscrew cover above the bulb (this can be found directly behind the loading aperture, at the top; refer to “Description of machine” section.)
2. Replace defective bulb.
3. Screw cover back down.
Check the correct positioning of o-ring gasket before screwing back the door light cover. Do not operate the dryer when missing oring gasket on door light cover.
Warning!
Do not use standard bulbs!
These develop too much heat and may damage the machine!
Warning!
operated.
For safety reasons, the cover must be screwed down tightly. If this is not done, the dryer must not be
Warning!
Before replacing the bulb, disconnect the mains plug.
TECHNICAL DATA
This appliance conforms with the following EU Directives:
– 2006/95/EC dated 12.12.2006 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive
92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
Height x width x depth
Drum volume
Depth with loading door open
Height can be adjusted by
Weight when empty
Loading volume (depends on programme)
1)
Voltage
Required fuse
Total power
Energy efficiency class
Energy consumption (7 kg of cotton, predrained at 1000 rpm)
2)
Use
Permissible ambient temperature
85 x 60 x 58 cm
108 l
109 cm
1.5 cm approx. 46 kg max.
7
kg
230V-240V
10A
2350
B
3,9
Domestic
+ 5°C to + 35°C
24
electrolux
Consumption values
The consumption values have been established under standard conditions. They may deviate when the machine is operated in domestic circumstances.
Programme
COTTON CUPBOARD
2)
Energy consumption in kWh
4,0 (7 kg load pre-drained at 800 rpm)
3,9
(7 kg load pre-drained at 1000 rpm)
3,6 (7 kg load pre-drained at 1400 rpm)
COTTON IRON
2)
SYNTHETICS CUPBOARD
2)
3.3
1,3
(7 kg load pre-drained at 1000 rpm)
(7 kg load pre-drained at 1200 rpm)
1) Different loading volume data may be needed in some countries as a result of different measuring methods.
2) in accordance with EN 61121
MACHINE SETTINGS
Setting
BUZZER permanent off
Water hardness
Water contains, a variable quantity of limestone and mineral salts of which quantities vary according to geographical locations thus varying its conductivity values.
Relevant variations of the conductivity of the water compared to those prefixed by the factory could slightly influence the residual humidity of the laundry at the end of the cycle. Your dryer allows you to regulate the sensitivity of the drying sensor based on conductivity values of the water.
Implementation
1. Turn the programme selector to any programme.
2. Press simultaneously the
DRYNESS
and
DELICATE
buttons and hold down for approx. 5 seconds.
3. The buzzer is by default always off. You can use
BUZZER
button to activate or deactivate sound but machine does not memorize your selection.
1. Turn the programme selector to any programme.
2. Press simultaneously the
DELICATE
and
START/PAUSE
buttons and hold down for approx. 5 seconds. The current setting is on the display:
–
low conductivity <300 micro S/cm
–
medium conductivity 300-600 micro S/cm
–
high conductivity >600 micro S/cm
3. Press the
START/PAUSE
button sequentially until you set desired level.
4. To memorize setting press simultaneously the the
DELICATE
and
START/PAUSE
buttons or turn knob to
O
OFF position
HINTS FOR TEST INSTITUTES
Parameters possible to checked by the
Test Institutes:
• Energy consumption (corrected with final humidity) during the cupboard dry cotton cycle with nominal load.
• Energy consumption (corrected with final humidity) during the cupboard dry cotton cycle with half load.
• Final humidity (during cupboard dry cotton, iron dry cotton and cupboard dry easy care)
• Condensation efficiency (corrected with final humidity) during cupboard dry cotton cycle with nominal and half load
All the cycles have to be checked in accordance with EN 61121 (Tumble dryers for household use – Methods for measuring the performance).
electrolux
25
INSTALLATION
Appliance positioning
• It is recommended that, for your convenience, the machine is positioned close to your washing machine.
• The tumble dryer must be installed in a clean place, where dirt does not build up.
• Air must be able to circulate freely all round the appliance. Do not obstruct the front ventilation grille or the air intake grilles at the back of the machine.
• To keep vibration and noise to a minimum when the dryer is in use, it should be placed on a firm, level surface.
• Once in its permanent operating position, check that the dryer is absolutely level with the aid of a spirit level. If it is not, raise or lower the feet until it is.
• The feet must never be removed. Do not restrict the floor clearance through deeppile carpets, strips of wood or similar.
This might cause heat built-up which would interfere with the operation of the appliance.
Important!
• The hot air emitted by the tumble dryer can reach temperatures of up to 60°C.
The appliance must therefore not be installed on floors which are not resistant to high temperatures.
• When operating the tumble dryer, the room temperature must not be lower than +5°C and higher than +35°C, as it may affect the performance of the appliance.
• Should the appliance be moved, it must be transported vertically.
• The appliance must not be installed behind the lockable door, a sliding door a door with a hinge on the opposite side to that of the appliance in such a way that a full opening of the dryer is restricted.
Removing transport safety packaging
Caution!
Before use all parts of the transport packaging must be removed.
1. Open loading door
2. Pull off adhesive strips from inside machine on top of drum.
3. Remove foil hose and polystyrene padding from the machine.
Drying rack unpacking
Caution!
Before appliance use all packaging parts and drying rack must be removed from the drum. The inside of the drum must be clean.
1 2
4 3
To unpack the rack:
1. Remove middle polystyrene part by pulling it.
26
electrolux
Loosen polystyrene parts 3 and 4.
4. Remove left polystyrene part by pulling it. Inside this part there is a canister for filling distilled water tank for steam programme purposes.
2. Lift slightly rack and take it carefully out from the drum.
3. Remove right polystyrene part by pulling it. Inside this part there is a bottle of distilled water for steam programme purposes.
Electrical connection
Details on mains voltage, type of current and the fuses required should be taken from the type plate. The type plate is fitted near the loading aperture (see “Product description” chapter).
Connect the machine to an earthed socket, in accordance with current wiring regulations.
Warning!
The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precautions.
Should the appliance power supply cable need to be replaced, this must be carried out by our Service
Center.
Warning!
The plug must be accessible after installing the machine.
electrolux
27
Door reversal
To make it easier to load or unload the laundry, the door can be reversed.
Warning!
The door must only be reversed by an authorised service engineer.
Please contact your local Service Force Centre. The engineer will carry out the door reversal at your cost.
Special accessories
•
Stacking kit
These intermediate installation kits can be used to arrange the dryer and a washing machine (60 cm wide, front loaded) as a space-saving washer/dryer stack.
The washing machine is at the bottom and the dryer is at the top.
Read carefully the instructions supplied with the kit.
Available from your Service Force Centre or your specialist dealer
•
Draining kit
SERVICE
If there are technical faults, first check if you can remedy the problem yourself with the help of the operating instructions - see chapter
What to do if….
If you cannot remedy the problem on your own, get in touch with the Customer Care
Department or one of our service partners.
To assist you quickly, these data are necessary:
– Model description
– Product number (PNC)
– Serial number (S No. is on rating plate stuck to the product - to find it see chapter
Product description
))
Installation kit for direct draining of the condensed water into a basin, siphon, gully, etc. The water reservoir then no longer has to be drained, it must however remain in its intended position in the machine.
Fixed hose has to be on the suitable height from minimum of 50 cm to maximum of 1 m from floor level and cannot be looped. If possible shorten the draining hose.
Read carefully the instructions supplied with the kit.
Available from your Service Force Centre or your specialist dealer
•
Pedestal with the drawer
To situate the dryer at the optimal height and have some additional space to store
(e.g. laundry).
Read carefully the instructions supplied with the kit.
Available from your Service Force Centre or your specialist dealer
– Type of failure
– Any error messages shown by the display.
So that you have the necessary reference numbers from your appliance at hand, we recommend that you write them in here:
Model description: ........................................
PNC:
S No:
........................................
........................................
www.electrolux.com/shop
136906442-A-322010
تنزيل
تم تحديث الرابط العام
رابط عام للمستند
إعلان