ZANUSSI ZSF2450S User Manual

EN
User manual
Dishwasher
ZSF2450S
Contents
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2
3
4
5
6
Hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9
Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10
Technical information _ _ _ _ _ _ _ _ _ _ _ _ 11
Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ 12
Subject to change without notice.
Safety instructions
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible if an incorrect
installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or
permanent disability.
• Do not let persons, children included, with reduced physical sensory, reduced mental
functions or lack of experience and knowledge use the appliance. They must have supervision or instruction for the operation of
the appliance by a person who is responsible
for their safety. Do not let children play with
the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door when it is open.
Installation
• Remove all the packaging.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where the
temperature is less than 0 °C.
• Obey the installation instruction supplied with
the appliance.
Water connection
• Make sure not to cause damage to the water
hoses.
2
• The appliance is to be connected to the water mains using the new supplied hose-sets.
Old hose sets must not be reused.
• Before you connect the appliance to new
pipes or pipes not used for a long time, let
the water flow until it is clean.
• The first time you use the appliance, make
sure that there is no leakage.
Electrical connection
Warning! Risk of fire and electrical shock.
• The appliance must be earthed.
• Make sure that the electrical information on
the rating plate agrees with the power supply.
If not, contact an electrician.
• Always use a correctly installed shockproof
socket.
• Do not use multi-plug adapters and extension
cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Contact the
Service or an electrician to change a damaged mains cable.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
Use
• This appliance is intended to be used in
household and similar applications such as:
– Staff kitchen areas in shops, offices and
other working environments
– Farm houses
www.zanussi.com
– By clients in hotels, motels and other residential type environments
– Bed and breakfast type environments.
Warning! Risk of injury.
• Do not change the specification of this appliance.
• Put knives and cutlery with sharp points in the
cutlery basket with the points down or in a
horizontal position.
• Do not keep the appliance door open without
supervision to prevent to fall on it.
• Do not sit or stand on the open door.
• Dishwasher detergents are dangerous. Obey
the safety instructions on the detergent packaging.
• Do not drink and play with the water in the
appliance.
• Do not remove the dishes from the appliance
until the programme is completed. There can
be detergent on the dishes.
Warning! Risk of electrical shock, fire or
burns.
• Do not use water spray and steam to clean
the appliance.
• The appliance can release hot steam if you
open the door while a programme operates.
Disposal
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and dispose of it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
Service
• Contact the Service to repair the appliance.
We recommend only the use of original spare
parts.
• When you contact the Service, ensure that
you have the following information that is
available on the rating plate.
Model :
PNC :
Serial Number :
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
Control panel
1
2
3
4
A B C
6
1 On/off button
2 Programme buttons
4 Indicators
5 Delay button
3 Display
6 Function buttons
www.zanussi.com
5
3
Indicators
Description
Washing phase indicator.
Drying phase indicator.
End indicator.
Salt indicator. This indicator is off while the programme operates.
Rinse aid indicator. This indicator is off while the programme operates.
Programmes
Programme1)
2)
3)
4)
Degree of soil
Type of load
Programme
phases
Duration
(min)
Energy
(kWh)
Water
(l)
Heavy soil
Crockery, cutlery,
pots and pans
Prewash
Wash 70 °C
Rinses
Dry
105
1.0
9
All
Crockery, cutlery,
pots and pans
Prewash
Wash 45°C or 70°C
Rinses
Dry
70 - 110
0.5 - 0.8
5-9
Normal soil
Crockery and cutlery
Prewash
Wash 55 °C
Rinses
Dry
160
0.63
7
Light soil
Crockery and cutlery
Wash 50 °C
Rinse
35
0.45
6
Normal or light soil
Delicate crockery
and glassware
Wash 40 °C
Rinse
30
0.40
6
1) The pressure and the temperature of the water, the variations of the mains supply, the options and the
quantity of dishes can change the programme duration and the consumption values.
2) The appliance senses the degree of soil and the quantity of items in the baskets. It automatically adjusts the
temperature and quantity of the water, the energy consumption and the programme duration.
3) With this programme you have the most efficient use of water and energy consumption for crockery and
cutlery with normal soil. (This is the standard programme for test institutes).
4) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
Information for test institutes
For all the necessary information for test performance. send an email to:
[email protected]
Write down the product number (PNC) that is on the rating plate.
4
www.zanussi.com
Before first use
1. Make sure that the set level of the water
softener agrees with the water hardness in
your area. If not, adjust the water softener.
Contact your local water authority to know
the water hardness in your area.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Processing residues can stay in the appliance. Start a programme to remove them.
Do not use detergent and do not load the
baskets.
Adjusting the water softener
Water hardness
German
degrees
(°dH)
French
degrees
(°fH)
mmol/l
Clarke
degrees
Electronic
adjustment
> 24
> 40
> 4.2
28
5
18- 24
32 - 40
3.2 - 4.2
22 - 28
4
12- 18
19 - 32
2.1 - 3.2
13 - 22
31)
4 - 12
7 - 19
0.7 - 2.1
5 - 13
2
<4
<7
< 0.7
<5
12)
1) Factory position.
2) Do not use salt at this level.
Electronic adjustment
1. Press the on/off button to activate the appliance. Make sure that the appliance is in setting mode. Refer to ‘SETTING AND STARTING A PROGRAMME’.
2. Press and hold function buttons (B) and (C)
at the same time until the indicators above
function buttons (A), (B) and (C) start to
flash.
3. Press function button (A).
• The indicators above function buttons (B)
and (C) go off.
• The indicator above function button (A)
continues to flash.
• The display shows the current setting of
= level 5.
the water softener, e.g.
4. Press function button (A) again and again to
change the setting.
5. Deactivate the appliance to confirm the setting.
www.zanussi.com
Filing the salt container
1
2
5
Filing the rinse aid dispenser
3
Put 1 litre of water in
the salt container (only for the first time).
4
1
2
max
5
6
Caution! Water and salt can come out
from the salt container when you fill it. Risk
of corrosion. To prevent it, after you fill the salt
container, start a programme.
3
4
You can turn the selector of the released
quantity between position 1 (lowest quantity) and position 6 (highest quantity).
Daily use
1. Open the water tap.
2. Press the on/off button to activate the appliance.
• If the salt indicator is on, fill the salt container.
• If the rinse aid indicator is on, fill the rinse
aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme for the
type of load and the degree of soil.
6
Using the detergent
1
2
www.zanussi.com
A
B
5. Adjust the water softener to the water hardness in your area.
6. Adjust the released quantity of rinse aid.
Setting and starting a programme
Setting mode
4
3
Fill the detergent dis- If you use a washing
penser (A) with deter- programme with pregent.
wash phase, put more
detergent in the prewash detergent compartment (B).
The appliance must be in setting mode to accept some operations.
The appliance is in setting mode when, after the
activation:
• All the programme indicators are on.
If the control panel shows other conditions,
press and hold function buttons (B) and (C) at
the same time until the appliance is in setting
mode.
Starting a programme without delay start
A
5
6
Using the combi detergent tablets
When you use tablets, that contain salt and
rinse aid, do not fill the salt container and the
rinse aid dispenser.
1. Adjust the water softener to the lowest level.
2. Set the rinse aid dispenser to the lowest position.
If you stop to use the combi detergent
tablets, before you start to use separately
detergent, rinse aid and dishwasher salt,
do these steps:
1. Press the on/off button to activate the appliance.
2. Set the water softener to the highest level.
3. Make sure that the salt container and the
rinse aid dispenser are full.
4. Start the shortest programme with a rinsing
phase, without detergent and without
dishes.
www.zanussi.com
1. Open the water tap.
2. To set a programme, keep the appliance
door ajar.
3. Press the on/off button to activate the appliance.
4. Make sure that the appliance is in setting
mode.
5. Press the button of the programme you
want to set.
• The programme duration flashes in the
display.
• The related programme indicator comes
on.
• The wash indicator comes on.
6. Close the appliance door. The programme
starts.
• The display shows the programme duration that decreases with steps of 1 minute.
• The wash indicator stays on.
Starting a programme with delay start
1. Set the programme.
2. Press the delay button again and again until
the display shows the delay time you want
to set (from 1 to 19 hours).
• The delay time flashes in the display.
• The delay indicator comes on.
7
3. Close the appliance door. The countdown
starts.
• The display shows the countdown of the
delay start that decreases with steps of 1
hour.
• The wash indicator goes off.
• When the countdown is completed, the programme starts.
– The delay indicator goes off.
– The wash indicator comes on.
– The display shows the programme duration.
You can set a programme, options and the
delay start also with the appliance door
closed. In this condition, you only have 3 seconds after each setting before the appliance
starts to operate.
Opening the door while the appliance
operates
If you open the door, the appliance stops. When
you close the door, the appliance continues
from the point of interruption.
Cancelling the delay start while the
countdown operates
Press and hold function buttons (B) and (C) at
the same time, until all the programme indicators come on.
When you cancel a delay start, the appliance goes back to setting mode. You have
to set the programme again.
Make sure that there is detergent in the detergent dispenser before you start a new
programme.
At the end of the programme
When the programme is completed the display
shows 0 and the wash indicator goes off.
1. Press the on/off button to deactivate the appliance.
2. Close the water tap.
• If you do not deactivate the appliance,
after three minutes from the end of the
programme:
– All the indicators go off.
– The display shows one horizontal status bar.
This helps to decrease the energy consumption.
Press one of the buttons (not the on/off
button), the display and the indicators
come on again.
• Let the dishes become cold before you
remove them from the appliance. Hot
dishes can be easily damaged.
• First remove the items from the lower
basket, then from the upper basket.
• There can be water on the sides and on
the door of the appliance. Stainless steel
becomes cool more quickly than the
dishes.
Cancelling the programme
Press and hold function buttons (B) and (C) at
the same time, until all the programme indicators come on.
Hints and tips
The water softener
Hard water contains a high quantity of minerals
that can cause damage to the appliance and
bad washing results. The water softener neutralises these minerals.
The dishwasher salt keeps the water softener
clean and in good conditions. It is important to
8
set the right level of the water softener. This
makes sure that the water softener uses the
correct quantity of dishwasher salt and water.
Loading the baskets
• Only use the appliance to wash items that are
dishwasher-safe.
www.zanussi.com
• Do not put in the appliance items made of
wood, horn, aluminium, pewter and copper.
• Do not put in the appliance items that can absorb water (sponges, household cloths).
• Remove remaining food from the items.
• Make soft the remaining burned food on the
items.
Using salt, rinse aid and detergent
• Only use salt, rinse aid and detergent for
dishwasher. Other products can cause damage to the appliance.
• The rinse aid helps, during the last rinsing
phase, to dry the dishes without streaks and
stains.
• Combi detergent tablets contain detergent,
rinse aid and other added agents. Be sure
that these tablets are applicable to the water
hardness in your area. Refer to the instructions on the packaging of the products.
• Detergent tablets do not fully dissolve with
short programmes. To prevent detergent residues on the tableware, we recommend that
you use the tablets with long programmes.
• Put hollow items (cups, glasses and pans)
with the opening down.
• Make sure that cutlery and dishes do not
bond together. Mix spoons with other cutlery.
• Make sure that glasses do not touch other
glasses.
• Put small items in the cutlery basket.
• Put light items in the primary basket. Make
sure that the items do not move.
• Make sure that the spray arm can move freely
before you start a programme.
Do not use more than the correct quantity
of detergent. Refer to the instructions on
the detergent packaging. The instructions on
the packaging usually refer to large dishwashers
(12 settings).
Before starting a programme
Make sure that:
• The filters are clean and correctly installed.
• The spray arm is not clogged.
• The position of the items in the baskets is
correct.
• The programme is applicable for the type of
load and for the degree of soil.
• The correct quantity of detergent is used.
• There is dishwasher salt and rinse aid (unless
you use combi detergent tablets).
• The cap of the salt container is tight.
Care and cleaning
Warning! Before maintenance, deactivate
the appliance and disconnect the mains
plug from the mains socket.
Dirty filters and clogged spray arm decrease the washing results.
www.zanussi.com
Make a check regularly and, if necessary, clean
them.
Cleaning the filters
Important! An incorrect position of the filters
can cause bad washing results and damage to
the appliance.
9
A
Cleaning the spray arm
Do these steps to remove and to put the spray
arm back:
B
1
2
Remove the filters A
and B from the bottom
of the appliance.
1
2
2
1
4
Fully clean the filters
below running water.
3
1
2
5
Put the filters back.
Turn the filter A
clockwise to lock it.
3
If the holes in the spray arms become clogged, remove remaining parts of soil with a
thin pointed object.
External cleaning
Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads or solvents.
Troubleshooting
The appliance does not start or it stops during
operation.
Before you contact the Service, refer to the information that follows for a solution to the problem.
With some problems, the display shows
an alarm code:
•
- The appliance does not fill with water.
10
•
- The appliance does not drain the water.
•
- The anti-flood device is on.
Warning! Deactivate the appliance before
you do the checks.
www.zanussi.com
Problem
Possible solution
You cannot activate the appliance.
Make sure that the mains plug is connected to the mains
socket.
Make sure that there is not a damaged fuse in the fuse box.
The programme does not start.
Make sure that the appliance door is closed.
If the delay start is set, cancel the setting or wait for the end
of the countdown.
The appliance does not fill with water.
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too
low. For this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter in the inlet hose is not clogged.
Make sure that the inlet hose has no kinks or bends.
The appliance does not drain the water.
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
The anti-flood device is on.
Close the water tap and contact the Service.
After the checks are completed, activate the appliance. The programme continues from the
point of interruption.
If the problem occurs again, contact the Service.
If other alarm codes appear, contact the Service.
Stains and dry water drops on glasses and
dishes
• The released quantity of rinse aid is not sufficient. Adjust the rinse aid selector to a higher
position.
• The quality of the detergent can be the
cause.
If the washing and drying results are not
satisfactory
Dishes are wet
• The programme is without a drying phase or
with a low temperature drying phase.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the cause.
Whitish streaks or bluish layers on
glasses and dishes
• The released quantity of rinse aid is too
much. Adjust the rinse aid selector to a lower
position.
• The quantity of detergent is too much.
Refer to ‘HINTS AND TIPS’ for other possible causes.
Technical information
Dimensions
Width / Height / Depth (mm)
Electrical connection
Refer to the rating plate.
Voltage
Frequency
Water supply pressure
Min. / max. (bar / MPa)
Water supply 1)
Cold water or hot water2)
Capacity
Place settings
www.zanussi.com
545 / 447 / 480
220 - 240 V
50 Hz
(0.8 / 0.08 ) / (10 / 1.0 )
max. 60 °C
6
11
Power consumption
Left-on mode
0.99 W
Off-mode
0.10 W
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
2) If the hot water comes from alternative sources of energy, (e.g. solar panels, aeolian energy), use the hot
water supply to decrease energy consumption.
Environment concerns
Recycle the materials with the symbol . Put
the packaging in applicable containers to
recycle it.
Help protect the environment and human health
and to recycle waste of electrical and electronic
appliances. Do not dispose appliances marked
12
with the symbol with the household waste.
Return the product to your local recycling facility
or contact your municipal office.
• Discard correctly the packaging material. Re.
cycle the materials with the symbol
www.zanussi.com
www.zanussi.com
13
14
www.zanussi.com
www.zanussi.com
15
156966170-B-202013
www.zanussi.com/shop