Yamaha HTR-6260 Zone 2 Hookup Example With Instructions

RX-V665/HTR-6260 Zone 2 Hookup Example
Zone 2
TV
HDMI
IN
HDMI
OUT
HDMI
IN 1
HDMI
IN 2
SPEAKERS
SIRIUS
DOCK
XM
(BD/DVD )
HDMI 2
HDMI 1
HDMI OUT
ANTENNA
COMPONENT
VIDEO
COMPONENT
VIDEO
PR
PR
GND
AM
HDMI 4
IN
PREPARATION
FM
ZONE2/PRESENCE
REMOTE
UNBAL.
PB
HDMI 3
EXTRA SP
OUT
PB
VIDEO
VIDEO
Y
12V
0.1A MAX.
Y
MONITOR OUT
FRONT
TRIGGER OUT
CENTER
SURROUND BACK/
BI-AMP
SURROUND
CENTER
CENTER
AV 1
OPTICAL
( TV )
COAXIAL
COAXIAL
AV 2
AV 3
(CD )
OPTICAL
AV 4
AV 5
AV 6
AV
OUT
FRONT
AUDIO1
Audio 1
Input
AUDIO2
SURROUND
SUR.BACK
MULTI CH INPUT
SUBWOOFER
AUDIO
OUT
FRONT
ZONE2
OUT
SURROUND
SUR. BACK
1 SUBWOOFER
2
PRE OUT
Audio 2
Input
HDMI
OUT
HDMI
OUT
Analog
Output
Analog
Output
BD/DVD player
NOTE:
To select the BD/DVD player as a
source for Zone 2, the Audio 1 input
on the receiver must be selected in
Zone 2.
Cable/Satellite Box
NOTE:
To select the Cable/Satellite Box as a
source for Zone 2, the Audio 2 input
on the receiver must be selected in
Zone 2
Zone 2 setup on the HTR-6260 using the Internal Power Amp
The HTR-6260 Extra Speaker Terminals can power one set of speakers for Zone 2 or Presence
speakers. If the Extra Speaker Terminals are utilized then the HTR-6260 cannot be set for 7.1
(Surround Back terminals.) or Bi Amp (Surround Back terminals.)
Setting the Extra Speaker Terminals
Note: The HTR-6260 remote control will be used to access the Setup Menu of receiver.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Press the Setup button on the remote control to enter the Setup Menu.
Setup, Speaker Setup will come up on the receiver LED Screen.
Press the Enter Button on the remote control.
Sp Set, 1 Auto Setup will come up on the receiver LED Screen.
Arrow down until 2 Manual Setup comes up in the receiver LED Screen.
Press the Enter Button on the remote control.
Manual Setup, A) Config will come up on the receiver LED Screen.
Press the Enter Button on the remote control.
SP Set, A) Config will come up on the receiver LED Screen.
Press the Enter Button on the remote control.
Config, Extra………None will come up on the receiver LED Screen.
Use the Left/Right Arrow buttons on the remote to change the Extra to: Extra……….Zone2.
Use the Return and Setup buttons on the remote to exit the Setup Menu.
Extra Speaker setup is complete.
To control Zone 2 using the HTR-6260 remote the switch at the upper most left hand corner of the remote
must be set to Zone 2. Once the remote has been set to Zone 2 the following commands will be
available:
1. Selecting the input source (AV5-6, AUDIO1-2, and V-AUX) of Zone 2.
2. Adjusting the volume of Zone 2 (when a Zone 2 speaker is connected to the EXTRA SP jack).
3. Tuning into FM or AM when “TUNER” is selected as the input source of Zone 2 (see page 29 of
the owner’s manual).
4. Tuning into XM Satellite Radio when “XM” is selected as the input source of Zone 2 (see page
31) (U.S.A. model only).
5. Tuning into SIRIUS Satellite Radio when “SIRIUS” is selected as the input source of Zone 2
(see page 35) (U.S.A. model only).
6. Playing back music stored on your iPod stationed in a Yamaha iPod universal dock (such as
YDS-10, YDS-11 and YDS-12 sold separately) connected to the DOCK terminal.
Note: Only Analog signals can be sent to Zone 2. If you want to output the sound from Zone 2, connect
an external component to AV 5-6 or Audio 1-2 by analog connection.
Important Safety Notice:
The EXTRA SP Speaker Terminals of this unit should not be connected to a Passive Loudspeaker
Selector Box or more than one Loudspeaker per Channel. Connection to a Passive Loudspeaker
Selector Box or Multiple Speakers per channel could create an abnormally low impedance load
resulting in amplifier damage.