advertisement
▼
Scroll to page 2
of 11
Visit us at : http://www.lgservice.com LG LG Dry Contact(Only AC 24V) INSTALLATION MANUAL Models: PQDSA1 PQDSB1 IMPORTANT • Please read this installation manual completely before installing the product. • Installation work must be performed in accordance with the national wiring standards by authorized personnel only. • Please retain this installation manual for future reference after reading it thoroughly. Dry Contact Unit Installation Manual TABLE OF CONTENTS ■ Safety Precautions .........................................................3~4 ■ Overview ............................................................................5 ■ Part Description .................................................................7 ■ Installation Guide ...............................................................8 ■ Installation Steps for Single Product..........................................................8 ■ Installation Steps for Multi Product ............................................................9 ■ Administrator Guide ........................................................10 2 Dry Contact Safety Precautions Safety Precautions To prevent injury to the user or other people and property damage, the following instructions must be followed. ■ Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. WARNING This symbol indicates the possibility of death or serious injury. CAUTION This symbol indicates the possibility of injury or damage. ■ Meanings of symbols used in this manual are as shown below. Be sure not to do. Be sure to follow the instruction. WARNING ■ Installation Don't touch with the hands while the power is on Use standard parts(connector). For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized Service Center. • There is risk of fire or electric shock. • Do not disassemble or repair the product. There is risk of fire or electric shock. • Do not disassemble or repair the product. There is risk of fire or electric shock. Installation Manual 3 Safety Precautions Use the correctly rated breaker or fuse. Do not install, remove, or reinstall the unit by yourself (customer). For installation, always contact the dealer or an Authorized Service Center. • There is risk of fire or electric shock. • There is risk of fire, electric shock, explosion, or injury. • There is risk of fire, electric shock, explosion, or injury. ■ Operation When the product is soaked (flooded or submerged), contact an Authorized Service Center. Be cautious that water could not enter the product. • There is risk of fire or electric shock. • There is risk of fire, electric shock, or product damage. 4 Dry Contact Overview Overview LG Dry Contact is a solution for automatic control of air conditioning system at the owner’s behest. In simple words, it’s a switch which can be used to turn the unit On/Off after getting the signal from external sources like key-in lock, door or window switch etc specially used in Hotel rooms. It’s a small PCB that either can be fit inside the control box of Indoor unit or can be outside the unit in a plastic case if there is no sufficient space inside the Indoor unit. Apart from simple installation, it can also be linked to Central Controller via Indoor unit PI485 pcb. For this, all connecting wires & an additional small pcb for looping is also provided along with Dry Contact. Dry Contact can be used in two ways. 1. It can be used to actually turn On/Off the system on receiving the signal from the source. In this case, user doesn't need to use remote controller anymore to turn On/Off the system. However all the further settings like temperature, fan speed, mode etc can be done through remote controller only. 2. Other way is almost similar as above but in this case, after getting the On signal from the external source, user has to turn On the system from remote controller only. Dry contact just activates the system. However system can be turned Off directly from the external source. So only On mode is different here. So in both of above conditions, system can’t be operated without signal from external source which prevents unnecessary use of system & facilitates its operation only when its required. These settings can be selected from the remote controller whose details have been explained in the later part of this manual So depending upon the requirement, Dry Contact offers a variety of applications to suit the customer’s requirement in the best possible way. Installation Manual 5 Part Description Power Connector Indoor PCB Connector Dry Contact Controller Connector 6 Dry Contact Part Description Part Description PQDSA1 (Only PCB) 1 2 3 4 5 6 PQDSB1 (PCB + Case) DRY CONTACT UNIT LG [Top case] [Bottom case] [Side] [Side] [ PCB ] [Side] 1 CN-POWER : AC 24V Connector 2 CN-CC : Indoor PCB Connector 3 CN_DRY (L) : DRY CONTROLLER Connector 4 CN_DRY ( SIG ) : DRY CONTROLLER Connector 5 CN_DRY (ERROR CHECK) : ERROR Check Display Connector 6 CN_DRY( OPER STATE): Operation Display Connector Installation Manual 7 Installation Guide Installation Guide Installation Steps for Single Product Connect CN-CC with Indoor PCB by the cable(provided) - Connection of Dry contact only DRY CONTACT SUB PCB Indoor PCB CN-CC 4 3 2 1 CN-CC 2 1 2 1 4 3 2 1 AC 24V - Connection of Dry contact & LG Central Controller in case of single constant models. Connection PCB (6871A30056A) DRY CONTACT SUB PCB Indoor PCB CN-CC 4 3 2 1 CN-CC 2 1 2 1 4 3 2 1 AC 24V S1 IC01A OSC01B L02D L01D C01A BR1 PI485 PCB : Special purchase for Central Control (Ex : PHNFP14A0 or PSNFP14A0...) SWITCH U04Y U02Y LED1 LED01G LED02G LED03G L1 2 3 4 ON U03Y C04Y C03Y TANS01Y ZNR01Y CN_COMM * (Cental Controller + Dry contact ) : indoor unit(Single) 8 Dry Contact Installation Guide Installation Steps for Multi Product Connect CN_DRY with Control Unit . (Fix SUB PCB into the proper location.) - To apply power source through PCB DRY CONTACT SUB PCB 4 4 3 3 CN-CC RY2 2 2 RY1 Operation Display Error Check Display 1 1 Dry contact Controller L N 2 1 2 1 INPUT AC 24V Local Install - To apply power source directly to external source DRY CONTACT SUB PCB 4 4 3 3 CN-CC RY2 2 2 RY1 Operation Display Error Check Display 1 1 Dry contact Controller L N 2 1 2 1 AC 24V Local Install Installation Manual 9 Administrator Guide Administrator Guide * Function It gives selection whether to turn ON the unit directly or not from the external source. The selection can be made by pressing CANCEL button of the wireless remote controller 3 times within 3 minutes of resetting the unit with facing it towards the unit. (This function availability depends on indoor unit model) ON OFF SET CANCEL CANCEL CANCEL Button ON OFF SET AUTO CLEAN PLASMA 1. To turn ON the unit directly from the external source 2. Not to turn ON the unit directly from the external source. Only to activate the system. If the power gives out, the Air conditioner may be run to before state after power returns because Air conditioner's function of interruption of electric power compensation. 10 Dry Contact P/No.: 3828A20494R Printed in Korea After reading this manual, keep it in a place easily accessible to the user for future reference.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement