Barco Graphics Tablet D320L Digitizer Installation guide

EVENTS
D320L DIGITIZER
INSTALLATION GUIDELINES
15042003
R5976542/00
Barco nv Events
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.88.24
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in Belgium
Changes
Barco provides this manual “as is” without warranty of any kind, either expressed or implied, including but
not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make
improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time
without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made
to the information in this publication; these changes are incorporated in new editions of this publication.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise
be recorded, transmitted or stored in a retrieval system without the prior written consent of BARCO.
Federal Communication Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area may
cause harmful interference, in which case the user will be responsible for correcting any interference.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights
of their respective holders. All brand and product names mentioned in this manual serve as comments or
examples and are not to be understood as advertising for the products or their manufactures.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee.
On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as
well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software
on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of
compliant, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period.
If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase
price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided
by Barco, being a component of the system or independent service, will be deemed invalid provided the damage
is not proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross
negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on good delivered by Barco, or if the goods
are handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the
purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as
well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in the this manual
must be complied with by the customer.
Table of contents
TABLE OF CONTENTS
1. Safety ..................................................................................................3
1.1Important Safety Instructions .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3
1.2Important Warnings . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 4
2. Introduction ..........................................................................................7
2.1General functionality .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 7
2.2Order info D320L Digitizer . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 7
2.3Technical summary . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 7
2.4Dimensions of the D320L Digitizer .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 8
3. Physical Installation of the D320L Digitizer...................................................9
3.1Installation requirements . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 9
3.2Connections . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 10
3.3Removing and inserting a D320L Digitizer input module . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 11
4. Input modules ..................................................................................... 13
4.1DVI input module.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 13
4.2SDI input module.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 14
4.3HDSDI input module .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 14
4.4CVBS / S-VID input module.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 16
4.5YUV / RG(s)B input module.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 16
4.6RGB analog input module.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 17
4.7Dummy input module . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 18
5. Cables and accessories for the D320L Digitizer........................................... 19
5.1Cables and accessories .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 19
6. Configuration schemes ......................................................................... 21
6.1Stand alone configuration .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 21
6.2Chaining configuration.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 21
6.3Stacking configuration .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 22
6.4Combined chained and stacked configuration . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 23
7. Control Software .................................................................................. 25
7.1XLite Toolset . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 25
7.2Version Control Manager (VCM) .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 25
8. Maintenance of the D320L Digitizer .......................................................... 27
8.1Cleaning the dust filter.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 27
8.2Cleaning the cabinet .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 27
9. Options .............................................................................................. 29
9.1Overview . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 29
Index .................................................................................................... 31
R5976542 D320L DIGITIZER 15042003
1
Table of contents
2
R5976542 D320L DIGITIZER 15042003
1. Safety
1. SAFETY
1.1 Important Safety Instructions
Instructions:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do NOT submerge fully or partly in water or other liquids.
Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking.
Consult the manufacturer for further advice should any doubts exist regarding any cleaning procedure.
Do not block ventilation openings. Install in accordance with the manufacturers instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding type plugs/sockets. If the provided
sockets / plugs are damaged then replacement of the defective parts must be undertaken immediately.
Protect the power/data cords from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Replace damaged power/data cords
immediately.
Only use attachments/accessories specified by the manufacturer.
Disconnect the power to this apparatus during lightning storms or provide suitable additional lightning
protection. Unplug this apparatus when unused for long period of time.
Refer all servicing to qualified service technicians/personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, the apparatus does
not operate normally, or has been dropped.
Use only with systems or peripherals specified by the manufacturer, or sold with the apparatus. Use
caution during lifting/moving or transporting to avoid damage by possible tipping.
R5976542 D320L DIGITIZER 15042003
3
1. Safety
1.2 Important Warnings
Important Warnings:
•
Risk of electric shock:
Image 1-1
Risk of electrical shock
•
•
•
•
•
4
Risk of electric shock. Do not open. To reduce the risk of electric shock, do not remove cover (or
back). No user-serviceable parts inside. Refer servicing to qualified service personnel.
The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this
product may cause a risk of electrical shock to persons.
The exclamation point within a triangle is intended to tell the user that important operating and/or
servicing instructions are included in the technical documentation for this equipment.
Maximum ambient temperature:
The maximum recommended ambient temperature for this equipment is 40 C.
Flammable materials:
Keep flammable materials away from the installation (such as curtains). A lot of energy is transferred
into heat. The installation should be such that the amount of air flow required for safe operation of the
equipment is not compromised. Proper ventilation must be provided.
This equipment MUST be earthed:
In order to protect against risk of electric shock, the installation should be properly grounded. Defeating the purpose of the grounding type plug will expose you to the risk of electric shock. This apparatus
must be grounded (earthed) via the supplied 3 conductor AC power cord. (If the supplied power cord
is not the correct variant, consult your dealer.)
Power system:
It is recommended to use a TN-S power distribution system (a power distribution system with a separate neutral and grounding conductor) in order to avoid large ground currents loops due to voltage
differences in the neutral conductor. The total electrical installation should be protected by an appropriate rated disconnect switch, circuit breakers and Ground Fault Current Interrupters. The installation
shall be done according to the local electrical installation codes. In Europe special attention should be
given to EN 60364, the standard for electrical installation of buildings. In Germany VDE 0100 should
be adhered to.
Mains cords:
The power cords delivered with this system have special properties for safety. They are not user
serviceable. If the power cords are damaged, replace only with new ones. Never try to repair a power
cord.
R5976542 D320L DIGITIZER 15042003
1. Safety
•
•
Use of an extension cord:
If an extension cord is used with this product, make sure that the total of the ampere ratings on the
products plugged into the extension cord does not exceed the extension cord ampere rating. Also
make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.
Cabinet openings:
Never push objects of any kind into this product through cabinet slots as they may touch dangerous
high voltage points or short out parts that could result in a risk of fire or electrical shock.
Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet,
unplug the set and have it checked by qualified service personnel before resuming operations.
R5976542 D320L DIGITIZER 15042003
5
1. Safety
6
R5976542 D320L DIGITIZER 15042003
2. Introduction
2. INTRODUCTION
2.1 General functionality
Overview
The D320L is a video processing device, designed to drive exclusively Barco LED walls. The D320L is
capable of handling all standard output formats like SVGA, XGA, SXGA and UXGA on an analog RGBHV
and digital DVI output.
The D320L Digitizer allows you to control up to 4 sources on one display. Seamless switch from source
to source or display sources together, overlay them, customize them. With analog and digital outputs
which allow for the control of displays, as well as built-in-control software, the D320L gives you control
over everything from basic set-up to configuration and advanced feature control.
The D320L Digitizer is a generic device. This means that a number of combinations can be made. Devices
can be chained in order to generate more windows on the output (4 windows per device). Devices can
also be stacked in order to be able to split generated output of the devices to multiple screens. For latter
purpose, each input is equipped with an active loop through.
2.2 Order info D320L Digitizer
Order info:
Article No.
Description
R9851570
D320L Digitizer
2.3 Technical summary
Summary
Type
Value
Input slots
4 input slots, front accessible, auto sensing and hot swappable
Compatibility
Barco LED walls
Output
DVI-A, Barco LED protocol
Scalability
Chaining for more inputs, stacking for more displays
Flexibility
User defined input
Scaler
4 input channels [Data-Video] fully independent scalable to desired
output resolution
Z-order control
Instant modification of Z-order control, for each output window
Window Positioning
Intuitive positioning interface
Connectors
RS 232 [RJ 11] — Ethernet [RJ 45]
R5976542 D320L DIGITIZER 15042003
7
2. Introduction
Type
Value
Effects
Anamorphic imaging, Chroma keying [per input], Alpha keying [per
input], Z-order control, Windowing/ View ports
Ruggedness
IP 10
Dimensions D320L
486 x 482 x 53 (W x D x H)
Dimensions D320L input Units
41 x 181 x 103 (W x D x H)
Weight
± 7 kg
Operating Temperature
0 ºC <> 45 ºC
Power consumption
130 Watt max at 85–264 Volt (50–60 Hertz)
Stacking
Up to 64 units (for 64 different displays)
Chaining
Up to 64 units (for 256 inputs)
2.4 Dimensions of the D320L Digitizer
Dimensions
Image 2-1
8
R5976542 D320L DIGITIZER 15042003
3. Physical Installation of the D320L Digitizer
3. PHYSICAL INSTALLATION OF THE
D320L DIGITIZER
3.1 Installation requirements
Requirements
•
•
•
The D320L Digitizer should not be placed in a built-in installation or enclosure unless proper ventilation
is provided.
When using the unit in a multi-unit rack assembly or closed assembly, the ambient temperature inside
the assembly may not exceed the maximum rated ambient temperature of the Digitizer. The installation should be such that the amount of air flow required for safe operation of the equipment in not
compromised.
When building in the D320L Digitizer into a rack with cover door, be aware that a space of 8,5 cm is
needed between the indicated reference and the cover door. This space is needed to guide the input
cables to the inputs.
Image 3-1
•
•
•
•
•
A Reference
The D320L Digitizer will require that air flows freely in vent holes. Blocking these holes will greatly
reduce the reliability of the unit and lead to the possibility of overheating.
The D320L Digitizer should operate from an AC power source. The D320L Digitizer is equipped with
Power Supply Autoranging from 85 to 264 volt (50–60 Hertz).
When installed in a rack, the mounting should be such that no hazardous condition is achieved due
to uneven mechanical loading.
When the mains switch located on the back of the D320L Digitizer is not accessible due to rack mounting, the socket outlet supplying the rack shall be installed near the equipment and be easily accessible
or a readily accessible disconnect device shall be incorporated in the fixed wiring. When using a rack
in an installation is advisable to log the serial number of the device and to activate the warranty figure
by registering utilizing the included form.
Do not place the D320L Digitizer on an unstable cart, stand or table. The device may fall, causing
serious damage to it.
R5976542 D320L DIGITIZER 15042003
9
3. Physical Installation of the D320L Digitizer
3.2 Connections
Rear panel inputs/outputs
Image 3-2
A
B
C
D
E
F
G
H
I
J
10
LED-WALL OUTPUT
Power Switch
Power input
LOOP IN
LOOP OUT
Retractable dust filter
COM1 : RS232 input
COM2 : RS232 chaining output
COM3 : RS232 stacking output
TCP-IP : Ethernet LAN connector
R5976542 D320L DIGITIZER 15042003
3. Physical Installation of the D320L Digitizer
•
•
•
•
•
•
•
•
•
•
A
B
-
: LED-WALL OUTPUT
LED wall out (Barco proprietary protocol).
RGB HV out (analog).
: Power switch
The power ON/OFF switch is provide on the rear side of the Digitizer.
o Switch pressed to 1 = the unit starts.
o Switch pressed to 0 = unit totally switched off.
C : Power input
- Autoranging from 90 to 260 VAC / 130 Watt.
D : LOOP IN
- From previous D320L Digitizer.
- Panel Link MDR26.
- Used for chaining multiple D320L digitizer to increase the number of usable input sources.
E : LOOP OUT
- To next Digitizer.
- Panel Link MDR26.
- Used for chaining multiple digitizer to increase the number of usable input sources.
F : Retractable dust filter
- The fan intake grill of the Digitizer has a retractable dust filter. This filter can be retracted from the
back of the unit. Check the filter for good functionality on a regular basis. Never allow this filter to
become blocked up and never operate the unit without a good working air filter in place.
G : COM1 : RS232 input
- Direct master.
- RS232 input port for communication links with local PC.
H : COM2 : RS232 chaining output
- RS232 output port for communication links from other D320L Digitizers in chain configuration
I : COM3 : RS232 stacking output
- RS232 output port for communication links from other D320L Digitizers in stacking configuration.
J : TCP-IP : Ethernet LAN connector
- For future use.
3.3 Removing and inserting a D320L Digitizer input module
There is no need to switch off the D320L Digitizer to remove or insert an input module.
The input modules are hot swappable.
How to remove an input module from the D320L Digitizer
1. Push in the release button underneath the input module which you want to remove. At the same time
pull out the input module by the grip handle. (image 3-3)
R5976542 D320L DIGITIZER 15042003
11
3. Physical Installation of the D320L Digitizer
Image 3-3
How to insert an input module into the D320L Digitizer
1. Gently slide in the input module into a free input slot with the grip handle at the top.
2. Locking in the module by pushing the input module completely into the D320L Digitizer until a definite
click is audible.
Maximum two HDSDI input modules may be inserted in one D320L Digitizer.
12
R5976542 D320L DIGITIZER 15042003
4. Input modules
4. INPUT MODULES
Overview
•
•
•
•
•
•
•
DVI input module
SDI input module
HDSDI input module
CVBS / S-VID input module
YUV / RG(s)B input module
RGB analog input module
Dummy input module
4.1 DVI input module
Technical info:
•
•
•
•
•
•
•
•
Computer generated graphical source.
DVI data in.
162 MHz pixel clock.
Resolution from VGA to UXGA/60 Hz.
DVI compliant.
DVI loop through.
Amber LED (upper LED on the front side) will be lit indicating module start up.
When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the
system acknowledges the module.
Image 4-1
Image 4-2
Order info:
Article No.
Description
R9850960
D320L Digitizer DVI input module
R5976542 D320L DIGITIZER 15042003
13
4. Input modules
4.2 SDI input module
Technical info:
•
•
•
•
•
•
•
SDI data in.
SDI loop through.
270Mbit/s transmission (SMPTE 259M-C).
525/625 interlaced.
Coax (75 Ohm).
Amber LED (upper LED on the front side) will be lit indicating recognition of film, either continuous or
intermittent film detection.
When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the
system acknowledges the module.
Image 4-3
Image 4-4
Order info:
Article No.
Description
R9850970
D320L Digitizer SDI input module
4.3 HDSDI input module
Maximum two HDSDI input modules may be inserted in one D320L Digitizer.
14
R5976542 D320L DIGITIZER 15042003
4. Input modules
Technical info:
•
•
•
•
•
HDSDI data in (SMPTE292M).
HDSDI loop through (SMPTE292M).
Coax (75 Ohm).
When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the
system acknowledges the module.
Supported HDSDI standards:
- Progressive:
o 1280x720/60/1:1/ (SMPTE 296M)
o 1280x720/59.94/1:1/ (SMPTE 296M)
o 1920x1080/30/1:1/ (SMPTE 274M)
o 1920x1080/29.97/1:1/ (SMPTE 274M)
o 1920x1080/25/1:1/ (SMPTE 274M)
o 1920x1080/24/1:1/ (SMPTE 274M)
o 1920x1080/23.98/1:1/ (SMPTE 274M)
- Interlaced:
o 1920x1035/60/2:1/ (SMPTE 260M)
o 1920x1035/59.94/2:1/ (SMPTE 260M)
o 1920x1080/60/2:1/ (SMPTE 274M)
o 1920x1080/59.94/2:1/ (SMPTE 274M)
o 1920x1080/50/2:1/ (SMPTE 274M)
o 1920/1080/50/2:1 (1250)/ (SMPTE 295M)
o 1920x1080/24/Segmented/ (SMPTE 274M)
o 1920x1080//23.98/Segmented/ (SMPTE 274M)
Image 4-5
Image 4-6
Order info:
Article No.
Description
R9850980
D320L Digitizer HDSDI input module
R5976542 D320L DIGITIZER 15042003
15
4. Input modules
4.4 CVBS / S-VID input module
Technical info:
•
•
•
•
Video (BNC)
- CVBS : 1Vpp ±3dB (0,7V Video +0,3V Sync) 75 Ohm termination.
- BNC loop through connector.
S-Video (4 pins DIN)
- Y : 1Vpp ±3dB (0,7V Video +0,3V Sync) 75 Ohm termination.
- U/V : 0,7Vpp ±3dB 100% color base, 75 Ohm termination.
- Chroma : Multi-Standard (PAL / SECAM / NTSC).
- 4 pins DIN loop through connector.
Amber LED (upper LED on the front side) will be lit indicating recognition of film, either continuous or
intermittent film detection.
When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the
system acknowledges the module.
Image 4-7
Image 4-8
Order info:
Article No.
Description
R9850920
D320L Digitizer CVBS / S-VID input module
4.5 YUV / RG(s)B input module
Technical info:
•
•
•
•
•
16
Component Video (BNC)
- R-Y : 0,7Vpp ±3dB 75 Ohm termination.
- Ys : 1Vpp ±3dB (0,7V Luma +0,3V Sync) 75 Ohm termination.
- B-Y : 0,7Vpp ±3dB 75 Ohm termination.
RG(s)B (BNC)
- R : 0,7Vpp ±3dB 75 Ohm termination.
- G(s) : 1Vpp ±3dB (0,7Vpp G + 0,3Vpp Sync) 75 Ohm termination.
- B : 0,7Vpp ±3dB 75 Ohm termination.
3 BNC’s loop through connectors.
Amber LED (upper LED on the front side) will be lit indicating recognition of film, either continuous or
intermittent film detection.
When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the
system acknowledges the module.
R5976542 D320L DIGITIZER 15042003
4. Input modules
Image 4-9
Image 4-10
Order info:
Article No.
Description
R9850940
D320L Digitizer YUV / RG(s)B input module
4.6 RGB analog input module
Technical info:
•
•
•
•
•
•
•
Sub D15 connector for input and loop through.
R, G, B, Hsync, Vsync : 0 to 1 Vpp ±3dB 75 Ohm termination.
Black level : 300mV.
Sync-tip : 0V
Resolution : SXGA and UXGA version available.
Amber LED (upper LED on the front side) will be lit indicating recognition of film, either continuous or
intermittent film detection.
When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the
system acknowledges the module.
Image 4-11
Image 4-12
Order info:
Article No.
Description
R9850950
D320L Digitizer RGB analog SXGA input module
R9851710
D320L Digitizer RGB analog UXGA input module
R5976542 D320L DIGITIZER 15042003
17
4. Input modules
4.7 Dummy input module
Technical info
•
Dimensions : 103 x 181 x 41(W x D x H)
Image 4-13
Image 4-14
Order info:
18
Article No.
Description
R9850930
D320L Digitizer dummy input module
R5976542 D320L DIGITIZER 15042003
5. Cables and accessories for the D320L Digitizer
5. CABLES AND ACCESSORIES FOR THE
D320L DIGITIZER
5.1 Cables and accessories
List with available cables and accessories
Article No.
Description
Image
R326103
Power cable with CEE7 plug.
image 5-1
R3261115
Power cable with NEMA 5–15 plug.
image 5-2
B5580491
Data cable with RJ12 connectors for RS232 connection between
local control PC and COM1 RS232 input port of the master Digitizer.
Also used to connect the COM2 or COM3 port with the COM1 port
of the following Digitizer.
image 5-3
Z3498421
RJ12–SUBD adapter.
image 5-4
R9827560
Data cable with SUBD connectors for RS232 connection between
local control PC and COM1 RS232 input port of the master Digitizer.
image 5-5
Z3499209
One meter data cable with MDR connectors. Used to make a
connection between the LOOP OUT connector of the previous
Digitizer and the LOOP IN connector of the next Digitizer.
image 5-6
R9851210
Five meter data cable with DVI connectors. Used to connect the
LED-WALL OUTPUT with an ILite display.
image 5-7
R9851216
Five meter data cable with one DVI connector and one waterproof
MDR connector. Used to connect the LED-WALL OUTPUT with an
DLite display.
image 5-8
R9851219
One meter data cable with one DVI connector and one MDR
connector. Used to connect the LED-WALL OUTPUT with a Fiberlink
Transmitter.
image 5-9
Image 5-1
Image 5-2
R5976542 D320L DIGITIZER 15042003
Image 5-3
19
5. Cables and accessories for the D320L Digitizer
20
Image 5-4
Image 5-5
Image 5-6
Image 5-7
Image 5-8
Image 5-9
R5976542 D320L DIGITIZER 15042003
6. Configuration schemes
6. CONFIGURATION SCHEMES
6.1 Stand alone configuration
Scheme
Image 6-1
One D320L Digitizer is sufficient to drive one Barco LED wall with four different sources.
How to set up a D320L stand alone configuration
1. Connect the RS232 communication port of the local control PC with the COM1 RS232 input port of the
D320L Digitizer.
2. Connect the LED-WALL OUTPUT from the D320L Digitizer with the display.
3. Provide the available video sources to the D320L input modules.
4. Configure the D320L Digitizer and the Display with the control software installed on the local control
PC.
6.2 Chaining configuration
Scheme
Image 6-2
R5976542 D320L DIGITIZER 15042003
21
6. Configuration schemes
The D320L Digitizer can be chained in order to generate more windows on the output display (four windows per D320L Digitizer).
How to set up a D320L chaining configuration
1. Connect the RS232 communication port of the local control PC with the COM1 RS232 input port of the
first D320L Digitizer. This Digitizer will act as the master, all following Digitizers are slaves.
2. Connect the LOOP OUT with the LOOP IN of the next D320L Digitizer in the chain.
3. Connect the COM2 RS232 output port with the COM1 RS232 input port of the next D320L Digitizer in
the chain.
4. Repeat step 2 and 3 until all D320L Digitizers in the chain are connected.
5. Connect the LED-WALL OUTPUT from the last D320L Digitizer in the chain with the display.
6. Provide the available video sources to the input modules of the D320L Digitizers.
7. Configure the D320L Digitizers and the Display with the control software installed on the local control
PC.
6.3 Stacking configuration
Scheme
Image 6-3
For some large installations is it necessary to divided a complete large display into two ore more screens
depending on the used frame rate and the amount of pixels per line and the total lines of the complete
display. For each screen a D320L Digitizer is used in stacking configuration. Consult Barco n.v. for advise
about the number of D320L Digitizers to be stacked.
22
R5976542 D320L DIGITIZER 15042003
6. Configuration schemes
How to set up a D320L stacking configuration
1. Connect the RS232 communication port of the local control PC with the COM1 RS232 input port of the
first D320L Digitizer. This Digitizer will act as the master, all following Digitizers are slaves.
2. Connect the LOOP OUT with the LOOP IN of the next stacked D320L Digitizer. This is necessary to
avoid synchronization problems between the screens
3. Connect the COM3 RS232 output port with the COM1 RS232 input port of the next stacked D320L
Digitizer.
4. Connect the LED-WALL OUTPUT with the one screen.
5. Repeat step 2, 3 and 4 until all D320L Digitizers are stacked.
6. Provide the available video sources to the input modules of one of the D320L Digitizers and use the
active loop through to connect the sources with the other stacked D320L Digitizers. Make sure the
same input source is used for the same input slot number on the different Digitizers.
7. Configure the D320L Digitizers and the Display with the control software installed on the local control
PC.
6.4 Combined chained and stacked configuration
Scheme
Image 6-4
It is possible to stack several chained D320L Digitizers in order to create a larger display with more than
4 windows. On condition that each chain in the stacked configuration has the same number of D320L
Digitizers.
R5976542 D320L DIGITIZER 15042003
23
6. Configuration schemes
How to set up a mixed configuration
1. Connect the RS232 communication port of the local control PC with the COM1 RS232 input port of the
first D320L Digitizer. This Digitizer will act as the master, all following Digitizers are slaves.
2. Connect the LOOP OUT of each previous Digitizer with the LOOP IN of the next Digitizer.
3. Connect the LED-WALL OUTPUT of the last Digitizer of each chain with a screen. Do this in a logical
order to simplify the configuration with the control software. First chain drives first screen from the left,
second chain drives second screen from the left and so on.
4. Connect each COM2 RS232 output port of the previous chained Digitizer with the COM1 RS232 input
port of the next chained Digitizer.
5. Connect each COM3 RS232 output port of the previous stacked Digitizer with the COM1 RS232 input
port of the next stacked Digitizer.
6. Provide the available video sources to the input modules and use the active loop through to connect
the sources with the other stacked input modules.
Note: The control software will recognize the chained Digitizers as one Digitizer in a stacked configuration. But instead of only 4 input slots the software will detect a plural of 4 input slots. Make sure
the same input source is used for the same input slot number on the different stacked Digitizers.
7. Configure the D320L Digitizers and the Display with the control software installed on the local control
PC.
24
R5976542 D320L DIGITIZER 15042003
7. Control Software
7. CONTROL SOFTWARE
7.1 XLite Toolset
General introduction
The XLite Toolset (R9850042) is used to configure and control the D320L Digitizer from basic set-up to
advanced features such as chroma keying, alpha blending or window positioning. Refer to the manual
(R5976380) for more information about the XLite Toolset.
7.2 Version Control Manager (VCM)
General introduction
The Version Control Manager (R9850044) is a stand alone program to update the software and firmware
of D320L Digitizer. The software runs from CD-ROM and acts like a wizard. So no installation is required.
The software runs on a Windows platform. Refer to the manual (R5976407) for more information about
the Version Control Manager.
R5976542 D320L DIGITIZER 15042003
25
7. Control Software
26
R5976542 D320L DIGITIZER 15042003
8. Maintenance of the D320L Digitizer
8. MAINTENANCE OF THE D320L
DIGITIZER
8.1 Cleaning the dust filter
The fan intake grill of the D320L Digitizer has a retractable dust filter which must be
checked for good functionality on regular basis. Never allow this filter to become
blocked up.
How to clean the dust filter
1. Softly press down the lid of the dust filter at the rear side of the D320L Digitizer and pull out the filter.
(image 8-1)
2. Blow out all the dust from the filter and remove remaining dust with a dry cloth.
3. Place the clean dust filter back in the D320L Digitizer.
Image 8-1
8.2 Cleaning the cabinet
Do not use liquid cleaners or aerosol cleaners. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet.
How to clean the cabinet
1. Unplug the D320L Digitizer from the wall outlet before cleaning.
2. Clean the cabinet with a damp cloth. Stubborn stains may be removed with a cloth lightly dampened
with mild detergent solution.
To keep the cabinet looking brand-new, periodically clean it with a soft dry cloth.
R5976542 D320L DIGITIZER 15042003
27
8. Maintenance of the D320L Digitizer
28
R5976542 D320L DIGITIZER 15042003
9. Options
9. OPTIONS
9.1 Overview
Order info:
Article No.
Description
R9851510
Climate Control Case for using the D320L
Digitizer outdoor
R5976542 D320L DIGITIZER 15042003
29
9. Options
30
R5976542 D320L DIGITIZER 15042003
Index
INDEX
A
Accessories 19
C
Cables 19
Cleaning 27
Air dust filter 27
Cabinet 27
Configuration scheme 21–23
Chaining 21
Mixed 23
Stacking 22
Stand alone 21
Configuration schemes 21
Connections 10
D320L 10
D
D320L 7–9, 13, 29
Dimensions 8
Functionality 7
Input modules 13
Installation 9
Requirements 9
Options 29
Technical summary 7
I
Input module 11, 13–14, 16–18
R5976542 D320L DIGITIZER 15042003
CVBS / S-VID 16
Dummy 18
DVI 13
HDSDI 14
Insert 11
Remove 11
RGB analog 17
SDI 14
YUV / RG(s)B 16
Introduction 7
D320L 7
M
Maintenance 27
O
Options 29
D320 29
Order info 7
D320L 7
S
Safety 3–4
Important Instructions 3
Warnings 4
Software 25
D320L 25
VCM 25
XLite Toolset 25
31
Index
32
R5976542 D320L DIGITIZER 15042003
Revision Sheet
To:
Barco nv Events/Documentation
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70, Fax: +32 56.36.88.24
E-mail: [email protected], Web: www.barco.com
From:
Date:
Please correct the following points in this documentation (R5976542/00):
page
R5976542
wrong
D320L DIGITIZER
correct
15042003