JVC MP3 Player RC-EX26B User manual

JVC MP3 Player RC-EX26B User manual
FIRST THINGS
ENGLISH
ADJUSTING THE SOUND
NAMES OF PARTS AND CONTROLS
Turn the VOLUME knob (or press VOLUME + / – button on the remote control unit) to increase or decrease
the volume to desired level. The volume level can be adjusted in 31 steps from “00” to “30”.
This portable system operates on battery or AC power.
Top and front sides:
CD PORTABLE SYSTEM
FM telecscopic antenna
BEAT CUT switch
RC-EX26B
• Turning off the sound temporarily
During playback, press MUTING to turn the sound off. The MUTING indicator appears in the display
window. Press it again to restore the sound.
Main unit
PHONES jack
1
2 3
4 5
6
7
8
STANDBY/ON
MUTING
• Reinforcing the bass sound
Press and hold HBS/PRESET EQ so that the HBS indicator appears in the display window. You can
enjoy powerful bass sound with the Hyper-Bass Sound effect.
FM MODE
Supplied power cord
HBS/
PRESET EQ
PROGRAM/
CLOCK SET
PUSH
AC outlet
Battery compartment
PR
ES
TA
P
E
RA
ND
OM
INSERTING BATTERIES
CD
CD
ET
RE
P
STO
SE
AU
Y/P
PLA
PE
AT
REMOTE
SENSOR
BAN
D
DISPLAY
1 Open the battery compartment cover.
Pull the battery compartment cover toward you while pressing the sections marked by the arrows.
CLASSIC: Enriched sound with fine treble and ample bass.
ROCK : Powerful sound emphasizing treble and bass.
POP : More presence in the vocals and midrange.
JAZZ : Accented lower frequencies for jazz-type music.
FLAT : Equalizer effect is canceled.
2 Insert six R20 (SUM-1)/D (13D)-size batteries. (not supplied)
Be sure to insert the batteries with the (+) and (–) terminals positioned correctly.
1
3
2
6
9
5
10 11
12 13
14 15
4
INSTRUCTIONS
R20 (SUM-1)/D (13D)-size batteries
3 Replace the battery compartment cover.
Thank you for purchasing this JVC product.
Please read these instructions carefully before starting operation to be
sure to obtain optimum performance and a longer service life from the
unit.
Inserting Batteries into the Remote Control Unit:
Match the polarity (+ and –) of the batteries. R03 (UM4)/AAA (24F) ×2 (supplied)
LVT1382-010A [E/EN]
0205NSMBICORI
EN ©2005 Victor Company of Japan, Limited
SAFETY PRECAUTIONS
Caution ––
STANDBY/ON switch!
STANDBY/ON switch in any
Disconnect the mains plug to shut the power off completely. The
position does not disconnect the mains line. The power can be remote controlled.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the
unit; leave all servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when open and interlock failed or
defeated. Avoid direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.
Note: The battery power will be switched off when you plug the power cord into the Ó AC
IN jack on the unit.
1 VOLUME knob
button
2 STANDBY/ON
3 PRESET – button
PRESET + / CD REPEAT button
4 Tape operation buttons
PAUSE 8 button
STOP/EJECT § button
FF 1 button
REW ¡ button
PLAY 2 button
REC ÷ button
5 CD door
6 FM MODE button
7 MUTING button
8 PROGRAM/CLOCK SET button
9 TAPE button
CD/RANDOM button
TUNER/BAND button
10 REMOTE SENSOR
11 Display window
12 Cassette deck
13 DISPLAY button
14 4 button
¢ button
PLAY/PAUSE 6 button
STOP 7 button
15 HBS/PRESET EQ button
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS
DEFEATED. AVOID EXPOSURE TO BEAM.
VORSICHT !
UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL
GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZEN!
Remote control unit
1
STANDBY/ON
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
SPÄRR ÄR URKOPPLAD STRÅLEN ÄR FARLIG.
ADVARSEL -
USYNLIG LASERSTRÅLING VED ÅBNING NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ
UDSÆTTELSE FOR STRÅLING.
USING HEADPHONES
Connect commercially available headphones to the PHONES jack on the rear of the main unit. While the
headphones are connected, the speakers do not produce any sound. Before connecting the headphones,
make sure to turn down the sound volume.
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front:
No obstructions and open spacing.
2 Sides/ Top/ Back:
No obstructions should be placed in the areas shown by the dimensions below.
3 Bottom:
Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand
with a height of 10 cm or more.
2
3
4
5
Front view
Side view
15 cm
15 cm
TUNER/
BAND
TAPE
INTRO
STOP
CD PLAY
/PAUSE
CD REPEAT/
+
HBS/
PRESET EQ
+
PRESET
MUTING
VOLUME
7
FM MODE
10 cm
TUNER
PROG
FM
MHz
9
5 Press PROGRAM/CLOCK SET while the PROG indicator is blinking.
The tuned station in step 2 is stored in the preset number selected in step 4. Storing a new station on a
used number erases the previously stored one.
6 Repeat steps 2 to 5 to preset other stations, using different preset numbers.
1 STANDBY/ON
button
2 CD/RANDOM button
TUNER/BAND button
TAPE button
3 INTRO button
4 FM MODE button
5 PRESET + /CD REPEAT button
PRESET – button
6 DISPLAY button
7 STOP button
CD PLAY/PAUSE button
4 button
¢ button
8 VOLUME + button
VOLUME – button
9 HBS/PRESET EQ button
MUTING button
GENERAL CONTROLS
STANDBY/ON
- Press to turn on/off the unit.
The display window lights up when the unit is turned on. (Note, however, that the display window does not
light even when the unit is turned on if the unit is operated on batteries.)
1 Press DISPLAY.
The clock flashes on the display window.
2 Press and hold PROGRAM/CLOCK SET for more than 2 seconds.
The hour digits start flashing.
4 Press 4 or ¢ adjust the minutes, then press PROGRAM/CLOCK SET.
Notes:
• If there is a power failure, the clock loses the setting and is reset to “0:00.” The clock indication will keep
flashing until you set the clock again.
• You can also set the clock when the unit is in STANDBY mode. In this case, follow the procedures from
step 2.
To show the clock when CD or tuner is selected.
Press DISPLAY.
Each time you press the button, the display changes the clock indication and the normal indication alternately.
(Operating the unit while clock indication is displayed changes the display to the normal indication.)
2
4 Press PRESET + /CD REPEAT or PRESET – to select the preset number while the PROG indicator
is blinking.
Preset number
–
3 Press 4 or ¢ to adjust the hour, then press PROGRAM/CLOCK SET.
The minute digits start flashing.
RC_EX26B[EEN].p65
FM
8
15 cm
10 cm
TUNER
PROG
MHz
SETTING THE CLOCK
15 cm
15 cm
15 cm
CD/
RANDOM
ANTENNAS
The AM antenna is built in, so adjusting the position of the unit may help AM reception. The FM telescopic
antenna on the back of the unit can be extended and rotated for better FM reception.
Changing the FM reception mode
When an FM stereo broadcast is hard to receive or noisy, press FM MODE so that the MONO indicator
appears in the display window.
To restore the stereo effect, press FM MODE again so that the MONO indicator goes off.
The MONO will be cancelled also when changing the station.
DISPLAY
Plug the power cord into the Ó AC IN jack on the back of the unit, and into an AC power outlet.
Note: To switch off the system completely, unplug the power cord.
VARNING -
1 Press TUNER/BAND to enter the tuner mode.
2 Press TUNER/BAND to select the band, FM or AM.
3 Press and hold 4 or ¢ for more than 1 second.
The unit starts searching and stops when a station of sufficient signal strength is tuned in.
If you press 4 or ¢ briefly and repeatedly, the frequency changes step by step.
6
–
CAUTIONS:
1. ONLY USE JVC POWER CORD PROVIDED WITH THIS UNIT TO AVOID MALFUNCTION OR
DAMAGE TO THE UNIT. REMOVE BATTERIES WHEN USING THE POWER CORD.
2. BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN
THE UNIT IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.
TUNING IN RADIO STATIONS
You can preset 10 FM and 10 AM stations.
1 Press TUNER/BAND to select the band, FM or AM.
2 Press 4 or ¢ to tune in the station you want to preset.
3 Press PROGRAM/CLOCK SET.
The PROG indicator starts blinking in the display window.
Names of buttons:
CAUTION:
To avoid battery leakage or explosion, handle batteries properly.
• If you are not going to use your system for a month or more, remove the batteries from the battery
compartment.
• Dispose of batteries in the proper manner, according to federal, state, and local regulations.
• Do not mix with different battery types or with new and old ones, or do not attempt to charge a
battery not intended to be recharged.
• Discard leaky batteries immediately. Leaking batteries can cause skin burns or other personal injury.
USING THE RADIO
PRESETTING STATIONS
SUPPRLYING AC POWER
CAUTION -
• Selecting the sound mode
You can select one of the 5 preset sound modes.
Press HBS/PRESET EQ repeatedly until the indicator for the sound mode you want appears in the
display window.
05.5.17, 8:09 PM
Tuning in a preset station
1 Press TUNER/BAND to select the band, FM or AM.
2 Press PRESET + /CD REPEAT or PRESET – repeatedly until the desired preset number appears.
Notes:
• In some cases, test frequencies have been already memorized for the tuner since the factory examined
the tuner preset function before shipment. This is not a malfunction. You can preset the stations you
want into memory by following the presetting method.
• If you unplug the AC power cord or if a power failure occurs, the preset stations will be erased in a few
days. If this happens, preset the stations again.
USING THE TAPE
PROGRAMMING
USING THE CD
|Forward direction
CLEANING THE TAPE HEADS
1 Press CD/RANDOM to enter CD mode.
2 Press PROGRAM/CLOCK SET in stop mode.
The PROG indicator starts blinking in the display window.
THINGS TO KNOW BEFORE PLAYING CDs
Clean the heads after every 10 hours of use with a wet-type head cleaning tape (available at electronic and
audio shops).
Pinch roller
CD
PROG
Playable CDs:
Only CDs bearing these marks can be used with this system.
Capstan
Head
Recordable
Erasure head
3 Press 4 or ¢ to select a desired track to be programmed while the PROG indicator is blinking.
ReWritable
CD
PROG
PAUSE 8 – Press to interrupt tape play or record mode. Press a second time to resume tape play or tape
record mode.
STOP/EJECT § – Press to stop the current tape activity, or to open the cassette compartment door
when no buttons are active.
FF 1 – In stop mode, press to advance the tape toward the end. (When the tape reaches the end, press
STOP/EJECT § to release the depressed button.)
REW ¡ – In stop mode, press to rewind the tape toward the beginning. (When the tape reaches the end,
press STOP/EJECT § to release the depressed button.)
PLAY 2 – Press to play cassettes.
REC ÷ – Press to record from the radio or CD player.
PLAYING A CASSETTE TAPE
1.
2.
3.
4.
5.
Press TAPE to enter the tape mode.
Press STOP/EJECT § to open the cassette compartment door.
Load a cassete. Use only a type-I normal tape.
Close the door securely.
Press PLAY 2 to begin playing the tape. The cassette tape plays until it reaches the end of the side,
then it automatically stops.
This unit has been designed only to play back the following CDs.
• Digital audio CD
• Recordable digital audio CD (CD-R)
• Rewritable digital audio CD (CD-RW)
Track to be programmed
When playing a CD-R or CD-RW
You can play back finalized CD-R or CD-RW recorded in music CD format. (If a CD-RW has been
recorded in a different format, erase all the data on the CD-RW completely before recording on it.)
• You can play back CD-R or CD-RW like an audio CD.
• Some CD-R or CD-RW may not be played back on this unit because of their disc characteristics,
damage or stain on them, or if the player lens is dirty.
• The reflection factor of CD-RW is lower than that of other CDs, possibly causing CD-RW to take longer
time to read.
• CD-R and CD-RW of MP3 format cannot be played back.
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.
STANDBY/ON
) PUSH
CD door
STANDBY/ON
Fast-winding a tape
Press REW ¡ or FF 1.
When the tape reaches the end, press STOP/EJECT § to release REW ¡ or FF 1.
MUTING
FM MODE
HBS/
PRESET EQ
PROGRAM/
CLOCK SET
PUSH
CD REPEAT
PR
ES
ET
TA
PE
RA
ND
OM
CD/RANDOM
CD
CD
BAND
RECORDING ON CASSETTE TAPES
OP
ST
/PAU
REP
EA
T
SE
AY
PL
REMOTE
SENSOR
DISPLAY
PLAY/PAUSE 6
You can record from the radio or the CD player.
• It may be unlawful to record or play back copyrighted material without the consent of the copyright
owner.
• The recording level is automatically set correctly, so it is not affected by the other sound settings. Thus,
during recording you can adjust the sound you are actually listening to without affecting the recording
level.
• If recordings you have made have excessive noise or static, the unit may be too close to a TV. Increase
the distance between the TV and the unit.
• You can only use type I tape for recording.
• DO NOT turn off the unit while playing back or recording a tape. The cassette deck or tapes may be
damaged.
• DO NOT use type II and type IV tapes since the unit is not compatible with such tapes.
• The use of C-120 or longer tape is not recommended, since characteristic deterioration may occur and
this tape easily jams in the pinch rollers and the capstans.
To protect your recordings
Cassettes have two small tabs on the back to protect against unexpected erasure or re-recording.
To protect your recording, remove these tabs.
To re-record on a protected tape, cover the holes with adhesive tape.
Adhesive tape
Checking the program contents
Before starting programmed playback, press PROGRAM/CLOCK SET.
Each time you press the button, the programmed tracks are shown in the display window.
Adding tracks in the program
1 Press PROGRAM/CLOCK SET repeatedly until “00” appears as a track number.
2 Press 4 or ¢ to select a new track number, then press PROGRAM/CLOCK SET.
Editing the program
1 Press PROGRAM/CLOCK SET repeatedly until the program number you want to edit appears.
2 Press 4 or ¢ to select a new track number, then press PROGRAM/CLOCK SET.
Erasing the entire program in the memory
Press PROGRAM/CLOCK SET so that the PROG indicator blinks, and press STOP 7 while the PROG
indicator blinks.
The stored program is also cleared when the CD door is opened.
CD/RANDOM
INTRO
DISPLAY
CD/
RANDOM
TUNER/
BAND
TAPE
INTRO
STOP
CD PLAY
/PAUSE
CD REPEAT/
+
HBS/
PRESET EQ
+
PRESET
MUTING
VOLUME
STOP
CD PLAY/PAUSE
FM MODE
CD REPEAT
–
–
Every track or every programmed track of a CD can be played for the beginning ten seconds.
Press INTRO on the remote control unit. The INTRO indicator appears in the display window and intro
playback starts. To use intro playback for programmed and random playback, press the button after starting
playback.
To quit intro playback, press INTRO again.
BEAT CUT
1
2
TIP
To temporarily pause the recording, press PAUSE 8 on the cassette deck. Press PAUSE 8 again to resume
recording.
SYNCHRONIZED RECORDING FROM A CD
1. Insert a cassette tape into the cassette deck and close the door.
2. Press CD/RANDOM.
3. Place a CD you want to record into CD compartment.
4. Select the track you want to record by pressing 4 or ¢.
5. Press REC ÷ to start synchronized recording.
Notes:
• When the tape reaches the end, the CD playback enters in pause.
To continue recording:
turn over the tape and press REC ÷.
To continue the CD playback:
press PLAY/PAUSE 6.
To stop the CD playback:
press STOP 7.
• When the CD playback stops, the cassette tape continues running.
To stop the cassette tape, press STOP/EJECT §.
TIP
Using the PAUSE 8 button on the cassette deck instead of the STOP/EJECT § button to momentarily
interrupt recording gives you a much clearer sound recording.
System does not turn on.
No sound
Poor radio reception
CD sound skips.
Distorted or noisy
recordings
Solution
• Make sure the power cord is securely plugged into the AC power
outlet (or that the batteries are fresh).
• Unplug the unit for a moment, and then plug it back in again.
• Check the outlet by plugging in another device.
• Adjust the volume setting.
• Make sure you have selected the correct function: CD, TAPE, or
TUNER and the headphones are disconnected.
• Adjust the FM telescopic antenna for better FM reception.
• Rotate the unit to achieve better AM reception.
• Try turning off electrical appliances near the unit, such as TV, hair
dryers, vacuum cleaners, or fluorrescent lights.
• Make sure the tray contains a CD.
• Make sure the CD’s label is facing up.
• Make sure that pause mode is not activated.
• Make sure the CD function is selected.
• Clean the CD (as explained in “CARE AND MAINTENANCE”).
• Check the CD for warping, scratches, or other damage.
• Check for vibration or shock that may affect the unit; move system if
necessary.
• Inspect the recording head and clean it if necessary.
• Demagnetize recording head (as explained in “CARE AND
MAINTENANCE”).
Resetting the unit
If “TROUBLESHOOTING TIPS” does not eliminate malfunctioning (failure to operate or display properly,
etc.), press the RESET button on the rear of the unit with something having a sharp point, while the unit is
turned on.
CLEANING THE EXTERIOR
• Disconnect the system from AC power before cleaning the exterior of the unit with a soft dry cloth.
LOADING A CD
Press CD/RANDOM; “00 00:00” flashes, then “no disc” appears in the display if no CD is loaded.
Press ) PUSH to open the CD door.
Place a CD into the tray with the label facing up.
Close the CD door. Then the total number of tracks and total playing time appear.
To remove the CD, press ) PUSH, grasp the CD by its edges, and carefully pull it out.
HANDLING DISCS
Sharp point
• Remove the disc from its case by holding it at the edge while pressing the
center hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc.
• Put the disc back in its case after use to prevent warping.
Note:
Resetting causes the unit to restore its factory default settings and results in all the settings made by the
user being deleted.
SPECIFICATIONS
• Be careful not to scratch the surface of the disc when placing it back in its
case.
• Avoid exposure to direct sunlight, temperature extremes, and moisture.
CD player
CD capacity
Dynamic range
Signal-to-noise ratio
AUTOMATIC SEARCH
Tuner
Automatic search quickly locates the beginning of any track on the CD, including the track currently playing.
If the CD is playing:
• Press 4 once to return to the beginning of the current track, press twice to return to the beginning of
the previous track.
• Press ¢ to skip to the beginning of the next track.
If the CD is stopped, repeatedly press 4 or ¢ until the display shows the number of the track you want
to play, then press PLAY/PAUSE 6. The CD player starts playing the selected track.
Frequency ranges
Antenna
To clean the disc
• Wipe the disc with a soft cloth in a straight line from center to edge.
• DO NOT use any solvent-such as conventional record cleaner, spray, thinner, or benzine-to clean the disc.
TRACK SEARCH
HANDLING CASSETTE TAPES
REPEAT
The CD REPEAT button repeats one track (REPEAT 1) or all tracks (REPEAT ALL). To scroll through the
choices, continuously press and release CD REPEAT, and check the display to see which choice you have
selected. The following chart illustrates how REPEAT works in various modes.
NORMAL
REPEAT ALL
• If the tape is loose in its cassette, take up the slack by inserting a pencil in one of
the reels and rotating.
• If the tape is loose, it may get stretched, cut, or caught in the cassette.
REPEAT 1
RANDOM
In CD mode, press CD/RANDOM. The RANDOM indicator appears in the display and random playback
starts.
To quit random playback, press CD/RANDOM again.
: 1 CD
: 60 dB
: 75 dB
: FM 87.5 - 108.0 MHz
: AM 522 - 1 629 kHz
: Telescopic antenna for FM
Ferrite core antenna for AM
Cassette deck section
Frequency response
Wow and flutter
: 60 Hz - 10 000 Hz
: 0.15% (WRMS)
General
• In play mode, press and hold ¢ to move forward through a track at high speed.
• In play mode, press and hold 4 to move backward through a track at high speed.
• Be careful not to touch the tape surface.
Speaker
Power output
Output terminals
Power supply
:
:
:
:
Power consumption
Dimensions
Mass
Accessories provided
:
:
:
:
9 cm cone × 2 (4 Ω)
4 W (2 W + 2 W) at 4 Ω (10% THD) (IEC268-3)
PHONES × 1 (∅ 3.5 mm, stereo)
AC 230 V Ó, 50 Hz
DC 9 V (“R20 (SUM-1)/D (13D)” × 6)
13 W (at operation), 3 W (on standby)
420 mm (W) × 178 mm (H) × 249 mm (D)
Approx. 3.2 kg (without batteries)
AC power cord × 1
Remote control unit × 1
Batteries for the remote control unit R03 (UM-4)/AAA (24F) × 2
Design and specifications are subject to change without notice.
ERASING
When recording on a pre-recorded tape, the previous recording is erased and only the new recording is
heard next time the tape is played back.
Erasing a recording on a tape without making a new recording
1. Press TAPE to enter the tape mode.
2 . Press REC ÷ to start recording.
RC_EX26B[EEN].p65
Problem
CARE AND MAINTENANCE
Press PLAY/PAUSE 6 to play all the tracks in order starting with track 1.
The current track number and elapsed playing time appear in the display.
Note: Press PLAY/PAUSE 6 to temporarily stop the CD. The elapsed playing time flashes in the display.
Press PLAY/PAUSE 6 again to resume playing the CD.
• Adjust VOLUME to a comfortable level.
• Press STOP 7 to stop playing the CD. Wait a few seconds for the CD to stop turning, then press )
PUSH to open the CD door and remove the CD.
Insert a cassette tape into the cassette deck and close the door.
Press TUNER/BAND and select a radio station.
Press REC ÷ to begin recording. REC ÷ and PLAY 2 are locked down.
Press STOP/EJECT § to stop recording.
TROUBLESHOOTING TIPS
CD does not play.
Note:
You can program up to 20 tracks in any desired order. The 21st program will overwrite the program number
“01”.
PLAYING A CD
RECORDING FROM THE RADIO
When recording an AM broadcast
When recording an AM broadcast, beats may occur. If this happens, set
the BEAT CUT switch to “1” or “2.”
Stopping programmed playback
Press STOP 7. The PROG indicator goes off and the unit exits from programmed playback.
To demagnetize the head
Turn off the unit, and use a head demagnetizer (available at electronic and audio shops).
INTRO PLAYBACK
STANDBY/ON
1.
2.
3.
4.
5.
1.
2.
3.
4.
4 (skip/search
backward)
PROGRAM/
CLOCK SET
¢ (skip/search
forward)
STOP 7
4 Press PROGRAM/CLOCK SET while the PROG indicator is blinking.
5 Repeat steps 3 and 4 to program other tracks.
6 Press PLAY/PAUSE 3/8 while the PROG indicator is blinking.
The tracks are played in the order you have programmed.
3
• Avoid storing tapes in any of the following places:
- In dusty places
- In direct sunlight or heat
- In moist areas
- On a TV or speaker
- Near a magnet
05.5.17, 8:09 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement