Sprint Nextel Cordless Telephone 2.4 GHz Digital Spread Spectrum Dual Keypad Cordless Phone with Caller ID/Call Waiting Owner's Manual

43-5522.fm Page 1 Tuesday, September 12, 2000 3:12 PM
2.4 GHz Digital Spread
Spectrum Dual Keypad
Cordless Phone
Please read before using this equipment.
Owner’s Manual
with Caller ID/Call Waiting
43-5522.fm Page 2 Tuesday, September 12, 2000 3:12 PM
ˆ Contents
Features .................................................................................................................................. 6
Installation .............................................................................................................................. 8
Mounting the Phone .......................................................................................................... 8
Connecting, Charging and Replacing the Battery Pack .................................................... 9
A Quick Look at the Handset .......................................................................................... 11
Setting the Dialing Mode ................................................................................................. 12
Setting the Ringer Tone/Volume ...................................................................................... 12
Turning Auto Talk On/Off ................................................................................................. 12
Turning Caller ID/Call Waiting On/Off ............................................................................. 12
Storing Your Area Code .................................................................................................. 13
Telephone Operation ............................................................................................................
Making and Receiving Calls ............................................................................................
Selecting the Channel .....................................................................................................
Adjusting the Handset Volume ........................................................................................
Using the Speakerphone .................................................................................................
Using Redial ....................................................................................................................
Using Flash .....................................................................................................................
Using Tone Services on a Pulse Line ..............................................................................
Using Page/Intercom .......................................................................................................
Memory Dialing ...............................................................................................................
Using a Headset ..............................................................................................................
13
13
14
14
14
14
15
15
15
16
18
Caller ID Operation ............................................................................................................... 19
Reviewing Caller ID Records .......................................................................................... 19
Adding/Deleting the Area Code ....................................................................................... 20
Dialing Numbers from a Caller ID Record ....................................................................... 20
Storing a Caller ID Record to Memory ............................................................................ 20
Deleting Caller ID Records .............................................................................................. 20
Using the Phone Company’s Network Service ............................................................... 21
Troubleshooting ................................................................................................................... 22
Care ................................................................................................................................ 23
RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.
The Sprint Logo is a registered trademark of Sprint Communications Company L.P. Used under license.
2
43-5522.fm Page 3 Tuesday, September 12, 2000 3:12 PM
This phone has been tested and found to
comply with all applicable UL and FCC standards.
WARNING: To reduce the risk of fire or
shock hazard, do not expose this product to rain
or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
!
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
This symbol is intended to alert
you to the presence of uninsulated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to constitute a risk of electric shock. Do
not open the product’s case.
!
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accompanying this product.
IMPORTANT CALLER ID
INFORMATION
To use the phone's Caller ID and Call Waiting with Caller ID features, you must be in an
area where those services are available and
you must subscribe to those services
through your local phone company. Where
Caller ID is offered, one or more options are
generally available:
• caller's number only
• caller's name only
READ THIS BEFORE
INSTALLATION
We have designed your phone to conform to
federal regulations, and you can connect it to
most telephone lines. However, each phone
(and each device, such as a telephone or answering machine) that you connect to the
telephone line draws power from the telephone line. We refer to this power draw as
the device's ringer equivalence number, or
REN. The REN is on the bottom of your
phone.
If you use more than one phone or other device on the line, add up all of the RENs. If the
total is more than five (or three in rural areas), your telephones might not ring. If ringer
operation is impaired, remove a device from
the line.
Your phone complies with Part 68 of FCC
Rules. You must, upon request, provide the
FCC registration number and the REN to
your telephone company. Both numbers are
on the bottom of your phone.
Note: You must not connect your phone to:
• coin-operated systems
• party-line systems
• most electronic key telephone systems
Important:
• Cordless phones such as this one
require AC power to operate. When the
AC power is off, you cannot dial out or
receive incoming calls using your
phone. For this reason, the phone
should not be your only telephone. To be
safe, you should also have a phone that
does not require AC power to operate
(not a cordless phone) so you can still
make and receive calls if there is an AC
power failure.
• caller's name and number.
3
43-5522.fm Page 4 Tuesday, September 12, 2000 3:12 PM
• Some cordless phones operate at frequencies that might cause interference
to nearby TVs and VCRs. To minimize
or prevent such interference, the base of
the cordless phone should not be placed
near or on top of a TV or VCR.
• Your cordless phone operates on standard radio frequencies, as allocated by
the FCC. Even though your phone's
access protection code prevents unauthorized use of your phone line, it is possible for other radio units operating on
similar frequencies within a certain area
to unintentionally intercept your conversations and/or cause interference. This
possible lack of privacy can occur with
any cordless phone.
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone causes
problems on the phone line, the phone company can temporarily discontinue your service. If this happens, the phone company
attempts to notify you in advance. If advance
notice is not practical, the phone company
notifies you as soon as possible and advises
you of your right to file a complaint with the
FCC.
Also, the phone company can make changes
to its lines, equipment, operations, or procedures that could affect the operation of this
telephone. The telephone company notifies
you of these changes in advance, so you can
take the necessary steps to prevent interruption of your telephone service.
4
LIGHTNING
Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
telephone line and power line current. These
protection circuits meet or exceed the FCC
requirements. However, lightning striking the
telephone or power lines can damage your
telephone.
Lightning damage is not common. Nevertheless, if you live in an area that has severe
electrical storms, we suggest that you unplug
your phone when storms approach to reduce
the possibility of damage.
FCC STATEMENT
The phone complies with the limits for a
Class B digital device as specified in Part 15
of FCC Rules. These limits provide reasonable protection against radio and TV interference in a residential area. However, your
equipment might cause TV or radio interference even when it is operating properly. To
eliminate interference, you can try one or
more of the following corrective measures:
• Reorient or
antenna.
relocate
the
receiving
• Increase the distance between the
equipment and the radio or TV.
• Use outlets on different electrical circuits
for the equipment and the radio or TV.
Consult your local RadioShack store if the
problem still exists.
43-5522.fm Page 5 Tuesday, September 12, 2000 3:12 PM
IMPORTANT SAFETY
INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock
and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on the product.
3. Never install telephone wiring during a
lightning storm.
4. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
5. Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the network interface.
6. Use caution when installing or modifying
telephone lines.
7. Do not fix the AC power supply cord to
building surfaces with metal fittings (if
the product has an AC power cord).
8. Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
9. Do not use this product near water, for
example, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
10. Do not place this product on an unstable
cart, stand, or table. The product may
fall, causing serious damage to the
product.
11. Slots and openings in the cabinet and
the back or bottom are provided for ventilation. To protect it from overheating,
these openings must not be blocked or
covered. The openings should never be
blocked by placing the product on a bed,
sofa, rug, or other similar surface. This
product should never be placed near or
over a radiator or heat register. This
product should not be placed in a built-in
installation unless proper ventilation is
provided.
12. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure
of the type of power supply to your
home, consult your local power company.
13. Do not allow anything to rest on the
power cord. Do not locate this product
where the cord will be stepped on.
14. Do not overload wall outlets and extension cords as this can result in a risk of
fire or electric shock.
15. Never push objects of any kind into this
product through cabinet slots as they
may touch dangerous voltage points or
short out parts that could result in a risk
of fire or electric shock. Never spill liquid
of any kind on the product.
16. To reduce the risk of electric shock, do
not disassemble this product. Take it to
a qualified serviceman when service or
repair work is required. Opening or
removing covers may expose you to
dangerous voltage or other risks. Incorrect reassembly can cause electric
shock when the product is subsequently
used.
17. Unplug this product from the wall outlet
and refer servicing to qualified service
personnel under the following conditions:
• When the power cord plug is damaged
or frayed.
5
43-5522.fm Page 6 Tuesday, September 12, 2000 3:12 PM
• If liquid has been spilled into the product.
• If the product has been exposed to rain
or water.
• If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are covered by the operating instructions
because improper adjustment of other
controls may result in damage and will
often require extensive work by a qualified technician to restore the product to
normal operation.
• If the product has been dropped or the
cabinet has been damaged.
• If the product exhibits a distinct change
in performance.
18. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
19. Do not use the telephone to report a gas
leak in the vicinity of the leak.
BATTERY SAFETY
INSTRUCTIONS
1. Use only the appropriate type and size
of battery pack specified in the instruction manual provided for this product.
2. Do not dispose of the battery pack in a
fire. The cell may explode. Check with
local codes for possible special disposal
instructions.
3. Do not open or mutilate the battery
pack. Released electrolyte is corrosive
and may cause damage to the eyes or
skin. It may be toxic if swallowed.
4. Exercise care in handling the battery
pack in order not to short it with conducting materials such as rings, bracelets,
and keys. The battery or conductor may
overheat and cause burns.
5. Charge the battery pack provided with or
identified for use with this product only in
accordance with the instructions and
limitations specified in the instruction
manual provided for this product.
6. Observe proper polarity orientation
between the battery pack and battery
charger.
SAVE THESE
INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF
FIRE OR INJURY, READ AND FOLLOW
THESE INSTRUCTIONS.
ˆ Features
Your Sprint 2.4 GHz Digital Spread Spectrum Dual Keypad Cordless Phone uses advanced technology to give you superior
audio quality and extended range.
The phone's Caller ID records each caller's
telephone number (and name, if available in
your area) and the date and time of the call,
6
as provided by your local phone company to
Caller ID service subscribers. If you subscribe to Call Waiting with Caller ID, the
phone can show you the incoming caller information, even when you are already talking
on the phone.
Features
43-5522.fm Page 7 Tuesday, September 12, 2000 3:12 PM
Your phone has these features:
2.4 GHz Operation — provides longer range
and less interference than many other cordless phones.
Spread Spectrum Technology — spreads
the signal across several frequencies for
added security during phone conversations.
Lighted Keypad — lights when you press
any key or receive a call, making the phone
easy to use, even in total darkness.
Caller ID Memory — stores up to 50 Caller
ID records.
Dual Keypads — a full set of keys on both
the handset and base let you use either keypad to operate the phone.
Speakerphone — lets you make or answer
calls without using the handset.
Facedown or Faceup Handset Charging
— you can place the handset on the base
face down or face up (to show the Caller ID
display, for example).
30 Channels — automatically selects a clear
channel when you make or answer a call.
Headset Jack — lets you connect an optional headset (available from your local
RadioShack store) for hands-free convenience.
Auto Talk — lets you set the phone so you
can answer a call simply by lifting the handset from the base or by pressing any key
when the handset is away from the base.
Ample Talk and Standby Time — the supplied battery (when fully charged) provides
about 7 hours of talk time or 7 days of standby time.
Network Service — supports the advanced
calling features Return Call, Repeat Dial, and
Cancel Call Waiting.
Security Access-Protection Code — automatically prevents other cordless phone users from using your phone line while the
handset is off the base.
3-Line Liquid Crystal Display with Backlight — lets you view an entire Caller ID
record on one screen.
Adjustable Ringers — you can set different
volumes for the handset and base ringer’s.
Two-Way Intercom/Paging System — lets
you send a signal from the base to the handset (or from the handset to the base) to page
someone or locate the handset when it is
away from the base. If someone answers at
the other end, you can use the phone as an
intercom.
30-Number Memory Dialing — lets you
store up to 30 numbers (20 in the handset
and 10 in the base) in memory for easy dialing.
Volume Control — lets you adjust the
volume you hear through the handset.
Redial — lets you quickly redial any of the
last three numbers dialed on the handset
and the last number dialed on the base.
Flash — sends an electronic switchhook signal for use with special phone services, such
as Call Waiting.
Tone/Pulse Dialing — lets you use your
phone with either type of service and you can
quickly switch from pulse to tone dialing for
long-distance, bank-by-phone, or other special services.
Hearing-Aid Compatibility — lets you use
the phone with hearing aids that have a T
(telephone) switch.
Features
7
43-5522.fm Page 8 Tuesday, September 12, 2000 3:12 PM
ˆ Installation
MOUNTING THE PHONE
You can place the phone on a desk or table,
or mount it on a standard wall plate or directly on a wall. Select a location that is:
jacks and adapters available at your local
RadioShack store, or have the telephone
company update the wiring for you.
The USOC number of the jack to be installed
is RJ11C (or RJ11W for a wall plate jack).
• near an AC outlet
On a Desk, Shelf, or Table
• near a telephone line jack
Follow these steps when you place the base
on a desk, shelf or table.
• out of the way of normal activities
• away from electrical machinery, electrical appliances, metal walls or filing cabinets, wireless intercoms, alarms, and
room monitors
• away from other cordless phones
The base's location affects the handset's
range. If you have a choice of several locations, try each to see which provides the best
performance.
1. Insert the bracket’s tabs into the base’s
upper tab slots, then press down on the
bracket’s clips and insert them into the
clip slots.
2. Plug one end of the supplied long modular cord into the TEL LINE jack on the
back of the base.
3. Route the modular cord through the
strain relief hook.
Cautions:
You must use a Class 2 power
source that supplies 9V AC
and delivers at least 350 mA.
Its center tip must be set to positive and
its plug must fit the phone's DC IN 9V
jack. The supplied adapter meets these
specifications. Using an adapter that
does not meet these specifications
could damage the phone or the adapter.
!
• Always connect the AC adapter to the
phone before you connect it to AC
power. When you finish, disconnect the
adapter from AC power before you disconnect it from the phone.
Note: Your telephone connects directly to a
modular telephone line jack. If your telephone wiring does not have a modular jack,
you can update the wiring yourself using
8
4. Plug the modular cord's other end into a
modular telephone line jack.
5. Insert the supplied AC adapter's barrel
plug into the DC IN 9V jack on the back of
the base.
6. Route the adapter's cord through the
strain relief slot on the bracket.
7. Plug the adapter into a standard AC outlet.
8. Lift the base's antenna to a vertical position.
Installation
43-5522.fm Page 9 Tuesday, September 12, 2000 3:12 PM
On a Wall Plate or Wall
1. Insert the bracket’s tabs into the base’s
lower tab slots, then press down on the
bracket’s clips and insert them into the
clip slots.
2. Plug one end of the supplied short modular cord into the TEL LINE jack on the
back of the base.
3. Insert the supplied AC adapter's barrel
plug into DC IN 9V jack on the back of the
base.
4. Route the adapter and modular cords
through the grooves on the bracket.
Note: To mount the phone directly on a wall,
you need two screws (not supplied) with
heads that fit into the keyhole slots on the
bottom of the base (minimum length 13/8
inches.
Follow the steps under “On a Wall Plate or
Wall,” then apply these additional instructions for placement on a wall.
15
1. Drill two holes 3 /16
inches (100 mm) apart.
Then thread a screw into
each hole, letting the
3
heads extend about /16
inch (5 mm) from the wall.
/16"
3
3 15/16"
2. Plug one end of the supplied long modular cord
into the TEL LINE jack on the back of the
base and route the adapter cable and
modular cords through the grooves on
the bracket.
3. Align the bracket's keyhole slots with the
mounting screws and slide the base
downward to secure it.
5. Plug the modular
cord's other end
into the wall plate
jack, then align the
bracket's keyhole
slots with the wall
plate studs and
slide the base downward to secure it.
6. Plug the adapter into a standard AC outlet.
7. Press and lift out the handset holder.
Rotate it 180°, then snap it back into
place so it holds the handset.
8. Lift the base's antenna to a vertical position.
CONNECTING, CHARGING
AND REPLACING THE
BATTERY PACK
The phone comes with a rechargeable
nickel-cadmium battery pack in the handset. Before using your phone, you must
connect the battery pack, then charge it for
about 24 hours.
Installation
9
43-5522.fm Page 10 Tuesday, September 12, 2000 3:12 PM
1. Press down and slide off the battery
pack compartment cover.
code, return the handset to the base for
about 5 seconds.
• Using a pencil eraser, clean the charging contacts on the handset and base
about once a month.
2. Lift the battery pack out of the compartment.
3. Plug the battery pack's connector into the
socket in the
compartment,
(the connector
fits only one
way), replace the battery pack, and
replace the cover.
To charge the battery pack, place the handset either faceup or facedown on the base.
The CHARGE/IN USE indicator on the base
lights and Total:00 appears.
Note: Be sure the battery is properly connected before you try to charge it. The
CHARGE/IN USE indicator flashes when the
handset is on the base with the battery not
connected.
Recharge the battery pack when Low Bat-
tery flashes.
Notes:
• When you first use the phone after
charging or recharging the battery pack,
the phone might not work and you might
hear a beep when you press TALK.
Return the handset to the base for about
5 seconds to reset the security accessprotection code.
• If the base loses power for 60 minutes
while the handset is away from it or the
the handset’s battery pack is completely
discharged, the security access-protection code might be lost. To reset the
10
• If the battery pack becomes weak during
a call, the handset beeps every 3 seconds and Low Battery flashes. When
this happens, you cannot make a call
until you recharge the battery pack.
• About once a month, fully discharge the
battery by keeping the handset off the
base until Low Battery flashes. Otherwise, the battery pack loses its ability
to fully recharge.
• If the display is blank and the phone
does not work, recharge the battery
pack. (The battery power might be too
low to light the display.)
• If you are not going to use your phone
for an extended period of time, disconnect the battery pack. This increases the
battery pack's usable life.
The supplied battery pack should last about
a year. If the battery pack does not hold a
charge for more than 2 hours after an overnight charge, replace it with a new 3.6-volt,
600 mAh battery pack with a connector that
fits the socket in the battery compartment.
You can order a replacement battery pack
through your local RadioShack store. Install
the new battery pack and charge it for about
24 hours.
Warning: Dispose of the old battery pack
promptly and properly. Do not burn or bury it
(see “Battery Safety Instructions” on Page 6
for additional information on proper battery
handling).
If you have trouble replacing the battery
pack, take the phone to your local
RadioShack for assistance.
Installation
43-5522.fm Page 11 Tuesday, September 12, 2000 3:12 PM
Important: The EPA certified
RBRC® Battery Recycling Seal
on the nickel-cadmium (Ni-Cd)
battery indicates RadioShack
is voluntarily participating in an
industry program to collect and recycle these
batteries at the end of their useful life, when
taken out of service in the United States or
Canada. The RBRC program provides a convenient alternative to placing used Ni-Cd bat-
teries into the trash or the municipal waste
stream, which may be illegal in your area.
Please call 1-800-THE-SHACK (1-800-8437422) for information on Ni-Cd battery recycling and disposal bans/restrictions in your
area. RadioShack’s involvement in this program is part of the company’s commitment to
preserving our environment and conserving
our natural resources.
A QUICK LOOK AT THE HANDSET
Note: The handset window has plastic film on it to protect it during shipment. Carefully peel off
the film before using your phone for the first time.
Use MEM to store or recall names and numbers
in memory (see “Memory
Dialing” on Page 16).
Use VOL/CID 8/9
9 to adjust the handset
volume (see “Adjusting the Handset
Volume” on Page 14), set the ringer/
tone volume (see “Setting the Ringer
Tone/Volume” on Page 12), view Caller
ID records (see “Caller ID Operation” on
Page 19), or select options.
Use FLASH to select
the phone's flash
function (see “Using
Flash” on Page 15).
Use TALK to make a
call (see“Making and
Receiving Calls” on
Page 13).
Use CID to review Caller
ID records.
Press
/TONE to use your
phone company's special
tone services when you are
on a pulse line (see “Using
Tone Services on a Pulse
Line” on Page 15).
Use RDL/PAUSE to redial
one of the last three numbers
dialed (see “Using Redial” on
Page 14) or store a pause in a
number (see “Entering a
Pause” on Page 17).
Use INTCM/DEL to page someone
at the base or transfer a call to the
base (see “Using Page/Intercom”
on Page 15), locate the handset, or
to erase information if you make a
mistake.
Use MENU to activate the
phone company's network
services (see “Using the
Phone Company’s Network
Service” on Page 21).
Installation
Use SELECT/CHANNEL to select the phone's channels (see
“Selecting the Channel” on
Page 14), and other options.
11
43-5522.fm Page 12 Tuesday, September 12, 2000 3:12 PM
SETTING THE DIALING
MODE
To set the base’s ringer volume, set RING
VOL on the back of the base to OFF, LO, or
HI.
Set PULSE-TONE on the back of the base for
the type of service you have. If you are not
sure which type you have, do this test after
you charge the handset's battery pack.
1. Set PULSE-TONE to TONE.
2. Lift the handset and press TALK, or
press SPEAKER. Listen for a dial tone.
3. Press any number other than 0.
Note: If your phone system requires that
you dial an access code (9, for example)
before you dial an outside number, do
not press the access code, either.
If the dial tone stops, you have touchtone service. Leave PULSE-TONE set to
TONE.
Note: When you set RING VOL to OFF, the
base (and the handset if it is on the base)
does not ring but other phones connected to
the same phone line rings. If the handset is
away from the base, it also rings.
TURNING AUTO TALK ON/
OFF
Your phone is preset so you must press
TALK when you lift the handset from the base
to answer a call. With auto talk turned on,
you can answer a call by just lifting the handset from the base. If the handset is away
from the base, you can answer by pressing
any key.
Follow these steps to turn auto talk on or off.
If the dial tone continues, you have
pulse service. Set PULSE-TONE set to
PULSE.
1. Lift the handset and hold down CID. A
menu appears with Auto Talk
selected.
4. Press TALK or place the handset on the
base to hang up.
2. Press SELECT/CHANNEL to change the
auto talk setting. On or Off appears.
3. Return the handset to the base or press
CID to store the new setting.
SETTING THE RINGER
TONE/VOLUME
You can select one of four different ringer
tone/volume settings on the handset. Repeatedly press VOL/CID 8 or 9 (except
during a call) to select the desired ringer setting. Each time you press a button, the
phone rings at the selected setting and
Ringer A High, Ringer A Low, Ringer B High, or Ringer B Low appears.
Note: Pressing VOL/CID 8 at Ringer A
High or VOL/CID 9 at Ringer B Low
does not change the setting. Press the opposite arrow key to change the setting.
Note: When auto talk is set to off, the handset continues to ring after you lift the handset
from the base until you press TALK.
TURNING CALLER ID/CALL
WAITING ON/OFF
If you subscribe to Call Waiting with Caller ID
service, you can set the phone to show Caller ID information for an incoming call even
while you are using the phone.
Follow these steps to turn the Caller ID/Call
Waiting feature on or off.
1. Lift the handset and hold down CID.
12
Installation
43-5522.fm Page 13 Tuesday, September 12, 2000 3:12 PM
2. Press 2 or VOL/CID 9 to select CIDCW
(Caller ID/Call Waiting).
Follow these steps to store your area code.
1. Lift the handset and hold down CID.
3. Press SELECT/CHANNEL to change the
Caller ID/Call Waiting setting. On or
Off appears.
4. Return the handset to the base to store
the new setting.
STORING YOUR AREA
CODE
2. Press 3 or VOL/CID
Area Code.
3. Press SELECT/CHANNEL, then enter
your three-digit area code. If you make a
mistake, repeatedly press 6 or 7 to
move the cursor over the incorrect digit,
then enter the correct number.
Note: If an area code is already stored,
it appears on the display. To delete the
area code, press INTCM/DEL three times
or hold down INTCM/DEL, then enter
your. area code. You can use 6 or 7
to move the cursor and edit the area
code.
You can store your local area code in the
phone's Caller ID record so it does not show
the area code if the received call is from your
local area. If for some reason you need to
dial the area code (or store it in the memory),
you can add it afterwards. See “Adding/Deleting the Area Code” on Page 20.
Note: If your calling area requires 10-digit dialing including area code, do not enter the
area code but leave this option blank.
9 twice to select
4. Press SELECT/CHANNEL to store the
area code, then press CID or return the
handset to the base to clear the display.
ˆ Telephone Operation
MAKING AND RECEIVING
CALLS
To make a call, lift the handset and press
TALK. Talk and the current volume setting
(see “Adjusting the Handset Volume” on
Page 14) appear, and the CHARGE/IN USE
indicator on the base lights. Then dial the
number. The number appears as you dial,
then (after a few seconds) the call's elapsed
time appears.
You can also dial the number then press
TALK. Talk and the current volume setting
appear, and the CHARGE/IN USE indicator
on the base lights. The number you entered
and the call’s elapsed time appear.
If you make a mistake, press INTCM/DEL until
the incorrect entry is erased, then enter the
correct number. To delete the entire number,
hold down INTCM/DEL for at least 1 second.
When you receive a call, Incoming Call
appears. To answer it, lift the handset from
the base and press TALK. If auto talk is on,
just lift the handset from the base. If the
handset is away from the base, press any
key. Talk and the current volume setting
appear.
To end a call, place the handset on the base
or press TALK.
Telephone Operation
13
43-5522.fm Page 14 Tuesday, September 12, 2000 3:12 PM
SELECTING THE CHANNEL
The phone has 30 channels. If the call
seems to disconnect for no reason during a
call, press SELECT/CHANNEL on the handset
to select a different channel. Scanning appears while your phone searches for a clear
channel.
ADJUSTING THE HANDSET
VOLUME
To adjust the handset’s volume during a call,
press VOL/CID 8 or 9 until you reach the
desired volume level. Volume Maximum,
Volume High, Volume Medium, or
Volume Low appears.
The setting is maintained even after you
hang up the phone.
Note: When you press VOL/CID 8 while the
volume is maximum or 9 while the volume
is low, the setting does not change and the
phone beeps three times.
Using Both the Handset and
Speakerphone
If someone else is using the speakerphone,
press TALK on the handset to join the conversation.
If someone else is using the handset, press
SPEAKER on the base to join the conversation.
During the call, one person can hang up and
let the call continue at the other keypad.
Or, both people can hang up at the same
time to end the call.
Note: If you hear a high-pitched noise from
the base's speaker, the handset and the
base are too close together.
USING REDIAL
USING THE
SPEAKERPHONE
To make or answer a call using the speakerphone, press SPEAKER. The SPEAKER indicator lights. When you hear a dial tone, dial
the number.
To set the speakerphone's volume, slide
VOLUME on the right side of the base.
To end a speakerphone call, press SPEAKER
again.
Switching Between the Handset
and Speakerphone
To switch to the speakerphone while you are
using the handset, press SPEAKER on the
base. When you hear the conversation or
dial tone on the speakerphone, press TALK
on the handset.
14
To switch to the handset while you are using
the speakerphone, simply lift the handset off
the base. If the handset is away from the
base, press TALK, then press SPEAKER.
You can quickly dial any of the last three
numbers you dialed on the handset. Lift the
handset and repeatedly press RDL/PAUSE
until the number you want to dial appears.
Then press TALK and the phone dials the
number.
You can also dial the last number dialed using the speakerphone. Press SPEAKER then
REDIAL/PAUSE on the base.
Notes:
• The redial memory for each keypad is
separate. You cannot redial a number
you dialed on the handset’s keypad
using REDIAL/PAUSE on the base’s keypad, and vice versa.
Telephone Operation
43-5522.fm Page 15 Tuesday, September 12, 2000 3:12 PM
• On the handset, press RDL/PAUSE after
pressing TALK to dial the last number
dialed.
• The redial memory holds up to 32 digits,
so you can redial long-distance as well
as local numbers.
• The redial memory also holds pause
entries. See “Entering a Pause” on
Page 17.
USING FLASH
FLASH performs the electronic equivalent of
a switchhook operation for special services,
such as Call Waiting.
For example, if you have Call Waiting, press
FLASH to answer an incoming call without
disconnecting the current call. Press FLASH
USING PAGE/INTERCOM
You can use the phone as a two-way pager
and intercom between the base and the
handset. This is useful if the handset is away
from the base and you want to locate it, or if
you want to have a conversation between
someone with the handset and someone at
the base.
To page the base from the handset, press INTCM/DEL. Paging Base appears, and the
base and handset ring. Press SPEAKER or
INTCM/PAGE on the base to answer the
page. Intercom appears.
To page the handset from the base, press INTCM/PAGE. The handset and base ring, and
Paging appears. Press TALK or INTCM/DEL
on the handset to answer the page. Intercom appears.
again to return to the first call.
Note: If you do not have any special phone
services, pressing FLASH might disconnect
the current call.
USING TONE SERVICES ON
A PULSE LINE
Some special services, such as bank-byphone, require tone signals. If you have
pulse service, you can still use these special
tone services by following these steps.
1. Be sure PULSE-TONE is set to PULSE.
2. Dial the service's main number.
3. When the service answers, press
/
TONE. Any additional numbers you dial
are sent as tone signals.
When you hang up, the phone automatically
resets to pulse dialing.
To end an intercom call, press TALK on the
handset, press SPEAKER on the base, or
hang up the handset.
If a call comes in during an intercom conversation, either the person at the base or the
person at the handset can answer the call.
Press TALK on the handset or SPEAKER on
the base once to end the intercom call, then
press TALK or SPEAKER again to answer the
incoming call.
Note: The intercom does not operate if the
party being paged is already on a call.
Transferring a Call between the
Handset and Base
You can use the phone's intercom feature to
transfer a call between the handset and the
base.
To transfer a call from the handset to the
base, press INTCM/DEL. The call is placed on
hold, and Paging Base and Hold appear.
Telephone Operation
15
43-5522.fm Page 16 Tuesday, September 12, 2000 3:12 PM
When the person at the base answers, press
TALK. The call is released from hold and
transferred to the base.
To transfer a call from the base to the handset, press INTCM/PAGE. The call is put on
hold, and Paging and Hold appear. When
the person with the handset answers, press
SPEAKER. The call is released from hold and
transferred to the handset.
MEMORY DIALING
You can store up to 30 phone numbers in
memory (20 in the handset’s and 10 in the
base’s memory), then dial a stored number
by entering its memory location number.
You can also store a name with each number
in the handset’s memory.
Use the supplied memory sticker to record
the numbers you stored in the base’s memory. Peel the backing from the sticker and attach the sticker to the base.
Storing a Number in the Handset's
Memory
Notes:
• The phone beeps five times exits the
storing process if you wait more than 20
seconds between each keypress.
• If you receive a call during memory
entry, the phone exits the storing process.
1. Lift the handset.
2. Hold down MEM until Memory Store
and a list of memory location numbers
appear.
3. Press a number (01-20) or VOL/CID 8 or
9# to choose a two-digit memory location. Precede a single digit location number with 0 — 01, 02, 03, and so on.
16
4. To store a name, press SELECT/CHANNEL. Store Name appears.
If you do not want to enter a name, skip
to Step 6.
5. To enter a name, press VOL/CID 8 or
9 to select the characters and 6 or 7
to move the cursor.
Repeatedly press VOL/CID 9 to view
the characters in alphabetical order.
(The display shows uppercase letters
first, then lowercase letters, numbers,
and special characters.)
Notes:
• Press VOL/CID 8 to see the characters in reverse alphabetical order.
• You can hold down VOL/CID 8 or 9
to scroll rapidly through the characters.
• If you make a mistake, move the cursor over the error, then enter the correct character, or press INTCM/DEL to
delete a character. To delete all the
characters, hold down INTCM/DEL for
at least 1 second.
6. Press SELECT/CHANNEL. Store Number appears.
7. Enter the phone number and any tone or
pause entries (see “Using Tone Services
on a Pulse Line” on Page 15 and “Entering a Pause” on Page 17).
8. Press SELECT/CHANNEL. The phone
beeps and Memory nn Stored
appear (nn is the location number you
selected). After 2 seconds, Memory
Store appears. Repeat Steps 3–8 to
store more numbers.
9. When you finish, press MEM.
Telephone Operation
43-5522.fm Page 17 Tuesday, September 12, 2000 3:12 PM
To replace a stored number, store a new one
in its place.
Editing or Deleting a Number in
the Handset’s Memory
Follow these steps to edit or delete a memory number.
1. Lift the handset.
2. Hold down MEM until Memory Store
and a list of memory location numbers
appear.
3. Choose a memory location (01–20) by
pressing a number or by repeatedly
pressing VOL/CID 8 or 9.
4. Press SELECT/CHANNEL. A menu
appears with the three options listed
below. Press VOL/CID 8 or 9 to highlight the desired option then press
SELECT/CHANNEL to choose it.
Edit Memory nn - edit the record as
described in Steps 5 through 7 of “Editing or Deleting a Number in the Handset’s Memory” on Page 17.
Delete Memory nn - the display
2. Enter the number (up to 16 digits) and
any tone or pause entries (see “Using
Tone Services on a Pulse Line” on
Page 15 and “Entering a Pause”).
Notes:
• The phone beeps five times and exits
the storing process if you enter more
than 16 digits.
• Each tone or pause entry uses one digit
of memory.
3. Press MEMORY again, then enter the
memory location number (0–9) where
you want to store the phone number. A
long beep indicates that the number is
stored.
To replace a number in the base's memory,
simply store a new number in its place. To
erase a memory number, press MEMORY
twice, then press the memory location number (0-9) you want to erase. A long tone indicates that the number has been erased from
the memory location.
Entering a Pause
Storing a Number in the Base's
Memory
In some telephone systems, you must dial an
access code (9, for example) and wait for a
second dial tone before you can dial an outside number. You can store the access code
with the phone number. However, you
should also store a pause after the access
code to allow the outside line time to connect. To enter a 2-second pause in the handset’s memory, press RDL/PAUSE. P appears
if you are storing a number into the handset’s
memory. You can add more pause entries
for a longer pause.
Note: The phone beeps five times and exits
the storing process if you wait more than 20
seconds between each keypress.
To enter a 2-second pause when storing a
number in the base’s memory, press REDIAL/
PAUSE.
prompts you to confirm the deletion.
Press VOL/CID 8 to move the cursor to
Yes, then press SELECT/CHANNEL or
INTCM/DEL. The phone beeps, and
Memory nn Deleted appears.
Go Back - returns you to the list of
memory numbers.
1. Press MEMORY. The CHARGE/IN USE
indicator blinks.
Telephone Operation
17
43-5522.fm Page 18 Tuesday, September 12, 2000 3:12 PM
Reviewing the Handset's Memory
Numbers
To review your handset's memory numbers,
press MEM. The list of memory location numbers (01–20) appears with the name stored
with each number (or <Memory nn> if you
did not store a name).
To see the stored phone numbers, select the
location you want to see using VOL/CID 8 or
9 or enter the location number, then press
7. An arrow to the right of the number
means it is longer than 13 digits. Press 7
again to see the rest of the number. Repeatedly press 6 to return to the name display.
Then, at the appropriate place in the call,
press MEM (or MEMORY on the base) and enter the number for the location where the additional information is stored.
Testing Stored
Emergency Numbers
If you store an emergency service's number
(police department, fire department, ambulance) and you choose to test the stored
number, make the test call during the late
evening or early morning hours to avoid peak
demand periods. Also, remain on the line to
explain the reason for your call.
To exit the memory number list, press MEM.
USING A HEADSET
To see a stored name and phone number at
the same time, press SELECT/CHANNEL
when the cursor is by a memory location
number. To exit this display, hold down INTCM/DEL until the display clears.
You can make or answer calls with handsfree convenience using an optional headset
3
that has a /32 -inch (2.5-mm) plug. Contact
your local RadioShack store for a suitable
headset.
Dialing a Memory Number
To connect the headset, pull open the rubber
cover marked
on the side of the handset,
then insert the headset's plug into the jack.
To dial a number stored in the handset’s
memory, lift the handset and press MEM. The
list of memory location numbers appears.
Choose a memory location (01–20) by pressing a number or by repeatedly pressing VOL/
CID 8 or 9, then press TALK.
To dial a number stored in the base's memory, press SPEAKER. When you hear a dial
tone, press MEMORY, then press the memory
location number for the number you want to
dial.
Note: If you select an empty memory location on the base, the base beeps 5 times.
Chain-Dialing Service Numbers
For quick recall of numbers for special services (such as bank-by-phone), store each
group of numbers in its own memory location. Dial the service's main number first.
18
Notes:
• Connecting a headset disconnects the
handset's earpiece and microphone.
• VOL/CID 8 or 9 on the handset also
controls the headset's volume.
• If you place the handset on the base to
recharge it while the headset is connected, be sure the handset seats properly.
Telephone Operation
43-5522.fm Page 19 Tuesday, September 12, 2000 3:12 PM
• You can use a handset holder (available
from your local RadioShack store) to
hang the handset on your belt for
greater convenience.
With a headset connected, you can make or
answer calls as usual using the speakerphone or keys on the handset.
When you finish using the headset, disconnect it from the handset and close the rubber
cover to protect the jack.
ˆ Caller ID Operation
If you subscribe to Caller ID service from
your phone company, the phone company
sends information about the call, as well as
the time and date, between the first and second rings of every call you receive.
The phone displays this information after the
second ring, and it stores up to 50 Caller ID
records for later review. It also shows if caller
information is unavailable or if the name and
number were blocked by the caller (see
“Caller ID Messages”).
If you subscribe to Call Waiting with Caller
ID, you will hear a tone through the handset
when a call comes in, then the Caller ID
record appears. If you want to answer the incoming call, press FLASH. To resume the
previous phone conversation, press FLASH
again.
If the phone's Caller ID memory becomes
full, any new call replaces the oldest call's
record.
REVIEWING CALLER ID
RECORDS
If the handset is faceup on the base, it shows
the number of new Caller ID records, if any,
and the total number of records.
est to the oldest, or VOL/CID 8 to scroll back
through the records. To scroll quickly through
the records, hold down VOL/CID 8 or 9.
When you scroll past the last record, the total
record number appears, then the first record.
When you scroll past the first record, the total
record number appears, then the last record.
The top line of each record shows the date,
time and the number of calls from that number. The second line shows the caller's
name, and the third line shows the caller's
phone number.
To exit the Caller ID record display, press
CID.
Caller ID Messages
Display
Description
NEW: XX
TOTAL: XX
Shows the number of new
Caller ID records (records
you have not viewed) and
the total number of records.
Private
Name
The caller has blocked the
Caller ID information.
or
Private
Number
To review the contents of each Caller ID
record, lift the handset and press CID to recall the number of records on the display.
Then, repeatedly press VOL/CID 9 to scroll
through the Caller ID records from the newCaller ID Operation
19
43-5522.fm Page 20 Tuesday, September 12, 2000 3:12 PM
Display
Unknown
Name
Description
The caller is not within a
Caller ID service area.
or
Unknown
Number
Incomplete
Data
Appears if there was an
error during the transmission of Caller ID information. Occasional errors are
normal. If the phone frequently displays Incomplete Data, contact
your local telephone company or RadioShack store.
ADDING/DELETING THE
AREA CODE
When the area code of the received call is
the same as the one you stored (see “Storing
Your Area Code” on Page 13), the caller ID
record does not show the area code. If it is
different, the record shows the area code.
However, you can add or delete the area
code on the display. When the record is on
the display, press 3 to add or delete the area
code. Pressing 3 again deletes or adds the
area code.
DIALING NUMBERS FROM A
CALLER ID RECORD
To dial a local number stored in a Caller ID
record, recall the record, then press TALK. If
it is a long distance call, press 1 (1 appears
before the displayed number) before you
press TALK. If you want to add or delete the
area code, press 3 before you press TALK.
Note: If a Caller ID record does not contain a
phone number (if it was blocked by the caller,
for example) you cannot dial from that
record.
20
STORING A CALLER ID
RECORD TO MEMORY
Follow these steps to store the name and
number from a Caller ID record into a memory location.
1. Press CID then VOL/CID 8 or 9 to
recall the record you want to store.
If you want to add or delete the area
code, press 3.
2. Press MEM.
appears.
Select
Location
3. Choose a memory location (01–20) by
pressing a number or by repeatedly
pressing VOL/CID 8 or 9, then pressing SELECT/CHANNEL.
If the selected location is empty, the
phone beeps to confirm that it stored the
number, then the Caller ID record
appears.
If a record exists in the selected location, Replace Memory? appears,
prompting you to confirm the replacement. Press VOL/CID 8 or 9#to#move
the cursor to Yes or No, then press
SELECT/CHANNEL. The phone beeps to
confirm the replacement.
DELETING CALLER ID
RECORDS
You can delete Caller ID records individually
or all at once.
Follow these steps to delete a single Caller
ID record.
1. Press CID then VOL/CID 8 or 9 to
recall the record you want to delete.
2. Press INTCM/DEL. Delete Message?
and Yes/No appear with the cursor
pointing to Yes.
Caller ID Operation
43-5522.fm Page 21 Tuesday, September 12, 2000 3:12 PM
3. Press SELECT/CHANNEL or INTCM/DEL.
The phone beeps once.
Follow these steps to delete all Caller ID
records.
Advanced Calling Services
Feature
Description
Return Call
The service retains the
number of the party that
called you last and
automatically dials that
number. Return call is
useful if you miss an
incoming call.
69
Repeat Dial
When you get a busy
signal or you want to
redial the last number
you called, the service
continuously redials the
number until the call
goes through.
66
Cancel Call
Waiting
Temporarily cancels
your Call Waiting service. This is useful
when you also use your
telephone line for internet service or sending/
receiving faxes. Enter
the key sequence prior
to dialing the internet or
fax number. Call Waiting is restored when
you disconnect the call.
70
1. Press CID so the record totals appear.
2. Press INTCM/DEL. Delete All? and
Yes/No appear with the cursor pointing
to No.
3. Press VOL/CID 8 to move the cursor to
Yes, then press SELECT/CHANNEL or
INTCM/DEL. The phone beeps once and
Total:00 appears.
USING THE PHONE
COMPANY’S NETWORK
SERVICE
Your phone supports advanced calling services provided by many phone companies
such as Return Call, Repeat Dial, or Cancel
Call Waiting.
To use these features, you must be in an
area where these services are available and
you must subscribe to these services
through your phone company. Contact your
local telephone company for more details on
how to subscribe.
The phone has the following features preprogrammed in its memory.
Important: Some phone companies use different key sequences to activate the features. If your phone company uses different
sequence, you must edit the sequence before using the service. See “Editing Advanced Service Names and Numbers.”
Press
Notes:
• When using certain calling features,
local, toll or long distance charges might
apply.
• You might not be able to use certain calling features on some long distance calls
or from certain types of business lines.
Follow these steps to access services.
1. Lift the handset.
2. Press MENU. Return Call, Repeat
Dial, and Cancel CW appear.
3. Press the number or VOL/CID 8 or 9
to select the service you want to use.
Caller ID Operation
21
43-5522.fm Page 22 Tuesday, September 12, 2000 3:12 PM
4. Press TALK. The selected service number appears and is dialed.
Note: You can display the programmed service number of each calling feature. At Step
2 above, press7 to view the number and 6
to return to the name display.
Editing Advanced Service Names
and Numbers
You might need to change the number
stored in any of the three service locations,
for example, if your phone company uses different number sequences from the programmed ones.
Follow these steps to edit a key sequence.
1. Lift the handset.
2. Hold down MENU until Select to
Edit and a list of calling features
appears.
4. Press SELECT/CHANNEL. A menu listing
Edit, Restore, and Go Back
appears. Press VOL/CID 8 or 9 to
highlight the desired option then press
SELECT/CHANNEL to choose it.
Edit — Service name appears.
Edit the service name and press
SELECT/CHANNEL. Then, Service
number appears. Edit the number and
press SELECT/CHANNEL. Enter the
name and number as described in Steps
5 through 8 of “Storing a Number in the
Handset's Memory” on Page 16.
Restore — prompts you to confirm
the restoration. If you want to return to a
preprogrammed calling feature, press
VOL/CID 8 to move the cursor to Yes,
then press SELECT/CHANNEL. The
phone beeps, and Service Setting
Restored appears.
Go Back — returns you to the list of
service numbers.
3. Choose a calling feature by pressing a
number (1–3) or VOL/CID 8 or 9.
ˆ Troubleshooting
We do not expect you to have any problems with your phone, but if you do, these suggestions
might help.
Problem
The phone does not work properly.
Suggestion
Be sure the base's phone line cord and AC adapter are correctly and
securely connected.
Be sure the battery pack in the handset is connected and charged.
Return the handset to the base for about 5 seconds to reset the security access-protection code.
The display flashes slowly
when the handset is faceup on
the base.
22
Make sure the battery pack in the handset is properly connected.
Troubleshooting
43-5522.fm Page 23 Tuesday, September 12, 2000 3:12 PM
Problem
The handset stops working or
works poorly during a call.
Suggestion
Move the handset closer to the base.
Lift the base's antenna to a fully vertical position.
Be sure the handset's battery pack is charged. (If the battery pack
power is too low, the handset cannot display Low Battery.)
Low volume or unusual
sounds.
Someone has picked up another phone on the same line. Hang up the
other phone.
Dropout or mute.
Keep the handset away from computers, remote control toys, wireless
microphones, alarm systems, intercoms, room monitors, fluorescent
lights, and electrical appliances. Move to another location or turn off
the source of interference.
Press SELECT/CHANNEL to change the channel.
Hang up and redial the number.
The phone cannot be operated
at a useful distance from the
base because the signal
becomes weak or noisy (handset's range has decreased).
Lift the base's antenna to a vertical position.
The handset battery pack does
not charge.
Check the charging contacts on the handset and base. If they are dirty,
clean them with a pencil eraser.
Be sure neither the handset's nor base's antenna is touching a metal
surface.
Return the handset to the base and recharge the battery pack.
Be sure the battery pack is connected correctly.
Be sure the handset is properly seated on the base.
Replace the battery pack (see “Connecting, Charging and Replacing
the Battery Pack” on Page 9).
The handset does not ring or
receive a page.
Move the handset closer to the base.
Lift the base's antenna to a vertical position.
Be sure the battery pack in the handset is connected and charged.
Move the base away from other electrical devices.
You have an incoming call, but
do not receive any Caller ID
information.
Let the phone ring twice before you answer so the phone has time to
record the Caller ID information.
Check that the phone is correctly and securely connected.
Check with your phone company to verify that your Caller ID service is
active.
If you still have problems, disconnect the phone. If other phones on the same line work properly, the fault is in this phone or its installation. If you cannot find the problem, take the phone to
your local RadioShack store for assistance.
CARE
• Keep the phone dry. If it gets wet, wipe it
dry immediately.
To enjoy your Sprint 2.4GHz Digital Spread
Spectrum Cordless Telephone for a long
time:
• Use and store the phone only in normal
temperature environments.
Troubleshooting
23
43-5522.fm Page 24 Tuesday, September 12, 2000 3:12 PM
• Handle the phone gently and carefully. Do not drop it.
• Keep the phone away from dust and dirt.
• Wipe the phone with a damp cloth occasionally to keep it looking new.
Modifying or tampering with the phone’s internal components can cause a malfunction and
might invalidate its warranty and void your FCC authorization to operate it. If your phone is not
performing as it should, take it to your local RadioShack store for assistance. If the trouble is
affecting the telephone lines, the phone company can ask you to disconnect your phone until
you have resolved the problem.
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
RadioShack Corporation
Fort Worth, Texas 76102
12/99
43-5522
UCZZ01695BZ
09A00
Printed in China