Vintec AL-V40DG2E User Manual

User Manual
V40DG2EBK
AL-V40DG2E
vintec.com
!
Important information that may impact
your Manufacturer’s Warranty
Adherence to the directions for use in this manual is extremely important for health
and safety. Failure to strictly adhere to the requirements in this manual may result
in personal injury, property damage and affect your ability to make a claim under the
Vintec manufacturer’s warranty provided with your product. Products must be used,
installed and operated in accordance with this manual. You may not be able to claim
on the Vintec manufacturer’s warranty in the event that your product fault is due to
failure to adhere this manual.
WARNING
The information in this document is subject to modification without
any prior notice.
Some models are available in dedicated countries only.
VINTEC offers no guarantee for our wine cellar if it is being used for any purpose other
than that for which it was specifically designed. VINTEC cannot be held responsible for
any error in this manual. VINTEC is not responsible or liable for any spoilage or damage
to wines or any other contents incidental or consequential to possible defects of the wine
cellar. Warranty applies to the wine cellar only and not to the content of the wine cellar.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
R600A WARNINGS
The following models use small quantity of R600A (iso-butane) flammable refrigerant:
AL/S3/BK:
V40DG 2e – 45g
For your safety please observe the following recommendations :
2
 This appliance contains a small quantity of R600A refrigerant which is
environmentally friendly, but flammable. It does not damage the ozone layer, nor
does it increase the greenhouse effect.
 During transportation and installation, ensure that the tubing of the refrigerant
User Manual
circuit is not damaged.
V40DG2EBK AL-V40DG2E
 Avoid using or manipulating sharp objects near by the appliances.
 Leaking refrigerant can ignite and may damage the eyes.
 In the event any damage does occur, avoid exposure to open fires and any device
Children should be supervised to ensure that they do not play with the appliance.
R600A WARNINGS
The following models use small quantity of R600A (iso-butane) flammable refrigerant:
AL/S3/BK:
V40DG 2e – 45g
For your safety please observe the following recommendations :
 This appliance contains a small quantity of R600A refrigerant which is
environmentally friendly, but flammable. It does not damage the ozone layer, nor
does it increase the greenhouse effect.
 During transportation and installation, ensure that the tubing of the refrigerant
circuit is not damaged.
 Avoid using or manipulating sharp objects near by the appliances.
 Leaking refrigerant can ignite and may damage the eyes.
 In the event any damage does occur, avoid exposure to open fires and any device
which creates a spark. Disconnect the appliance from the mains power.
 Thoroughly ventilate the room in which the appliance is located for several
minutes.
 Notify Customer Service for necessary action and advice.
 The room for installing the appliance must be at least 1 cubic metre per 8 grams of
refrigerant. The refrigerant quantity contained in this appliance is listed above in
grams; it is also noted on the Rating Plate of the appliance.
It is hazardous for anyone other than an Authorised Service Person to carry out
servicing or repairs to this appliance.
– WARNING: Keep ventilation openings in the appliance enclosure or in the built-in
structure clear of obstruction.
– WARNING: Do not use mechanical devices or other means to accelerate the defrosting
process, other than those recommended by the manufacturer.
– WARNING: Do not damage the refrigerant circuit.
– WARNING: Do not use electrical appliances inside the compartments.
– WARNING: In Queensland Australia, the authorized person must hold a Gas Work
Authorisation for hydrocarbon refrigerants, before carrying out servicing or repairs which
involve the removal of covers.
The environment and personal safety must be considered when disposing of this appliance.
Please ensure the appliance is taken to a recycle center for safe recycling. DO NOT
dispose of the appliance in land fill as the insulation and refrigerant gas contained in these
appliances are flammable.
Allow 24 hours before switching on the wine cellar. During this time we recommend
that you leave the door open to clear any residual odors.
BEFORE LOADING & PLUGGING IN THE WINE CELLAR
Important: All models without front venting (air opening) are strictly for free standing
only. (See technical chart)
User Manual
Recommendations:
The location you have selected for your wine cellar should:
- be unencumbered and well ventilated;
- be well away from any heat source and direct sunlight;
- not be too damp (laundry, pantry, bathroom etc.);
V40DG2EBK AL-V40DG2E
3
The environment and personal safety must be considered when disposing of this appliance.
Please ensure the appliance is taken to a recycle center for safe recycling. DO NOT
dispose of the appliance in land fill as the insulation and refrigerant gas contained in these
appliances are flammable.
Allow 24 hours before switching on the wine cellar. During this time we recommend
that you leave the door open to clear any residual odors.
BEFORE LOADING & PLUGGING IN THE WINE CELLAR
Important: All models without front venting (air opening) are strictly for free standing
only. (See technical chart)
Recommendations:
The location you have selected for your wine cellar should:
- be unencumbered and well ventilated;
- be well away from any heat source and direct sunlight;
- not be too damp (laundry, pantry, bathroom etc.);
- have a flat floor;
- have a standard and reliable electricity supply (standard socket to country standards,
linked to the ground), it is NOT recommended to use a multi-socket or extension lead;
- have a surge protector fitted to the electrical outlet;
- away from the microwave oven. Certain microwave ovens do not have wave interference
shield. When placed within 1 meter vicinity of the wine cabinet, they may affect the
operation of the wine cabinet.
The wine cellar should be placed where the ambient temperature is between 5ºC to 35ºC.
If the ambient temperature is above or below this range, the performance of the unit may
be affected. Placing your unit in extreme cold or hot conditions may cause interior
temperatures to fluctuate. The ideal range of temperature may not be reached. (See
Climate Class at the end of this manual)
Grounding instructions
The wine cellar must be grounded in case of an electrical short circuit. Grounding reduces
the risk of electrical shock. The wine cellar is equipped with a power cord having a
grounding wire and plug. The wine cellar plug must be plugged into a properly affixed and
grounded electrical outlet.
Note: In locations where there is frequent lightning, it is advisable to use surge
protectors.
Improper use of the grounding plug can result in the risk of electric shock. Consult a
qualified electrician or service person if the grounding instructions are not completely
understood.
If the supply cord is damaged, it must be replace by a qualified person in order to avoid
electrical hazard.
INSTALLING YOUR WINE CELLAR
4
Unpack and remove all of the protection and adhesive strips from the packaging around
and inside the wine cellar.
The wine cellar must be positioned such that the plug is accessible. Release the power
User Manual
cord. Move your wine cellar to its final location. The wine cellar should be installed in a
suitable place where the compressor will not be subject to physical contact. V40DG2EBK AL-V40DG2E
Leveling your wine cellar: Wine cellar must be leveled BEFORE loading your wines.
protectors.
Improper use of the grounding plug can result in the risk of electric shock. Consult a
qualified electrician or service person if the grounding instructions are not completely
understood.
If the supply cord is damaged, it must be replace by a qualified person in order to avoid
electrical hazard.
INSTALLING YOUR WINE CELLAR
Unpack and remove all of the protection and adhesive strips from the packaging around
and inside the wine cellar.
The wine cellar must be positioned such that the plug is accessible. Release the power
cord. Move your wine cellar to its final location. The wine cellar should be installed in a
suitable place where the compressor will not be subject to physical contact.
Leveling your wine cellar: Wine cellar must be leveled BEFORE loading your wines.
Your Vintec wine cellar is equipped with 4 adjustable feet to facilitate easy leveling.
VINTEC recommends that you tighten the back feet to the maximum and adjust the front
feet
to level
the wine
cellar.
Fixing
the Back
spacer:
Compressor
run appliances
Fixing the Back
spacer: require proper ventilation for proper and longer usage. Your
Vintec
wine
cellar
is supplied
with aproper
back spacer.
Affixfor
theproper
back spacer
at theusage.
back of
the
Compressor run appliances
require
ventilation
and longer
Your
cellar
air cellar
circulation
and heat
evacuation.
Vintecfor
wine
is supplied
with
a back spacer. Affix the back spacer at the back of the
cellar for air circulation and heat evacuation.
IMPORTANT - THIS SPACER MUST BE ATTACHED TO THE UNIT BEFORE
THE INSTALLATION, FOR VENTILATION PURPOSE. FAILURE TO DO SO VOIDS THE
IMPORTANT - THIS SPACER MUST
BE ATTACHED TO THE UNIT BEFORE
WARRANTY
THE INSTALLATION, FOR VENTILATION PURPOSE. FAILURE TO DO SO VOIDS THE
WARRANTY
User Manual
V40DG2EBK AL-V40DG2E
5
1. Vintec “Built in” wine cellars are front venting but are not designed to be fully
integrated behind a joinery door.
2. Vintec “Built in” wine cellars require 10mm clearance on both sides and top, 30mm
clearance at the rear (Back spacer is provided),to facilitate installation, removal, servicing
and ventilation.
3. Vintec “Built in” wine cellars draw air from the rear and expels through the metal grid
under the door at the front. If a kick board is to be placed in front of the wine cellar’s grid
another one must be fitted into the kick board with a minimum air flow allowance of
150cm2.
4. Vintec “Built in” wine cellars have a power switch located on the control panel so
power point location is not critical.
5. The wine cellar requires a standard 240 volt/10 amp power point. (Or according to
different countries specifications).
6. The power cord is 1.9m in length and is fixed on the right side at the back when looking
from front of cabinet.
7. As with most appliances of today, the wine cellar has sensitive electronic components
which are susceptible to damage through lightning and electricity supply faults. It is
therefore advised to use a power surge protector to avoid problems of this nature.
8 Air vent within the joinery must be provided for Vintec built in wine cellars (front
venting)
In Hot climate zone, an air vent or grid, with a minimum ventilation size of 200mm x
40mm MUST be cut out at the rear top of the back partitioning or at the top of either side
of the partitioning, allowing cool fresh air full access to flow into the 30mm gap located at
the rear of the cabinet.
This air vent or grid must not be opened on the same side as other appliances such as
ovens or an area that is sealed and without access to fresh cool air. Failing to comply with
the above specifications could result in WARRANTY void.
User Manual
6
V40DG2EBK AL-V40DG2E
INSTALLATION DRAWINGS FOR BUILT IN WINE CELLARS:
User Manual
V40DG2EBK AL-V40DG2E
7
Dimension and Installation Guide
Dimensional drawings:
40 Bottle Wine Cabinet
V40DG2EBK
615
595
10
30
850
820
30
10
593
563
Spacer
FRONT VIEW
SIDE VIEW
10
30
NOTE: Illustrations not to scale.
All dimensions in millimetres.
10
Spacer
For complete installation instructions,
please refer to the user manual for
this product.
TOP VIEW
© 2018 Electrolux Home Products Pty Ltd ABN 51 004 762 341 VDIM_V40DG2EBK_DimSheet
1800 771 776
vintec.com.au
User Manual
8
V40DG2EBK AL-V40DG2E
Dimension and Installation Guide
40 Bottle Wine Cabinet
AL-V40DG2E
615
595
30
10
830
820
10
10
593
563
Spacer
FRONT VIEW
SIDE VIEW
10
30
NOTE: Illustrations not to scale.
All dimensions in millimetres.
10
Spacer
For complete installation instructions,
please refer to the user manual for
this product.
TOP VIEW
© 2018 Electrolux Home Products Pty Ltd ABN 51 004 762 341 VDIM_AL-V40DG2E_DimSheet
1800 771 776
vintec.com.au
User Manual
V40DG2EBK AL-V40DG2E
9
TURNING ON YOUR WINE CELLAR
Plug in and switch on the cellar by pressing on the power button for a few seconds.
When you use the wine cellar for the first time (or restart the wine cellar after having it
shut off for a long time), there will be a few degrees variance between the temperature you
have selected and the one indicated on the LED readout. This is normal and it is due to
the length of the activation time. Once the wine cellar is running for a few hours
everything will stabilize.
Important: If the unit is unplugged, power is lost, or turned off, wait 3 to 5 minutes
before restarting the unit. The wine cellar will not start if you attempt to restart before
this time delay.
Operating Noises
To reach the desired temperature settings, VINTEC wine cellars, like all wine cellars
operating with compressors and fans, may produce the following types of noises. These
noises are normal and may occur as follows:
- Gurgling sound - caused by the refrigerant flowing through the appliance’s coils.
- Cracking/popping sounds - resulting from the contraction and expansion of the
refrigerant gas to produce cold.
- Fan operating sound - to circulate the air within the wine cellar.
An individual’s perception of noise is directly linked to the environment in which the wine
cellar is located, as well the specific type of models. VINTEC wine cellars are in line with
international standards for such appliance. VINTEC will always do its utmost to satisfy its
customers but will not retake possession of the goods due to complaints based on normal
operating noise occurrences.
LOADING YOUR WINE CELLAR
You may load your wine bottles in single or double rows while taking note of the
following: if you do not have enough bottles to fill your wine cellar, it is better to
distribute the load throughout the wine cellar so as to avoid “all on top” or “all below”
type loads.
- Do remove or relocate adjustable wooden shelves to accommodate larger type of bottles
or increase the capacity of the cellar by stacking the bottles up when necessary. (See
removing shelves)
- Keep smalls gap between the walls and the bottles to allow air circulation. Like an
underground cellar air circulation is important to prevent mould and for a better
homogeneous temperature within the cellar.
User Manual
10
V40DG2EBK AL-V40DG2E
- Do not over load your wine cellar to facilitate air circulation.
- Do not stack more than 1.5 rows of standard 0.75L bottles per shelves to facilitate air
circulation
- Avoid obstructing the internal fans (located inside on the back panel of the wine cellar).
- Do not slide the shelves outwards beyond the fixed position to prevent the bottles from
falling.
- Do not pull out more than one loaded shelf at a time as this may cause the wine cellar to
tilt forward.
- Do not cover the wooden shelves with alloy foil or other materials, as it will obstruct air
circulation.
- Do not move your wine cellar while it is loaded with wines. This might distort the body
of the wine cellar and cause back injury.
TYPES OF REGULATION
Please note that depending on the loading and settings chosen it takes about 24 hours for
the wine cellar to see the temperature stabilizing.
During this time LED seems to move erratically. It is normal and this process occurs
whenever the setting is modified and/or whenever a large amount of bottles are added to
the cellar.
Two Compartment single temperature wine cellars (2-in-1 Wine Cellars): electronic
regulation digital display
DG models are made of two independent compartments regulated independently as 2
single zone wine cellars. Like the e models, each compartment are adjustable from 6ºC to
18ºC. Ideal for storage or “mise en temperature” (The right temperature for optimum
enjoyment)
User Manual
V40DG2EBK AL-V40DG2E
11
TEMPERATURE SETTINGS
Important: The LCD displays by default the actual internal air temperature.
The temperature settings are pre-set at the factory as follows. In the event of a power
interruption, all previous temperature settings are automatically erased and it will revert to
the preset temperature settings.
Factory preset chart
Setting
Right compartment: 12
Temperature
12ºC (+/- 2.5ºC)
Left compartment: 7
7ºC (+/- 2.5ºC)
It is important to understand that there is a difference between the air temperature
inside the wine cellar and the actual temperature of the wine: You will need
to wait approximately 12 hours before noticing the effects of temperature adjustment
due to the critical mass within a full wine cellar.
Once the temperature is set, it is strongly advised not to toy with it or adjust
frequently. The thermostat will maintain the temperature inside the wine cellar within
a +/- 2.5ºC range. But the thermal inertia of the wine and the glass is such that within
this temperature range, the actual temperature of the wine will only fluctuate 0.5ºC to 1ºC.
The “DISPLAY LED” displays the internal temperature. The set temperature
automatically appears by pressing either the UP or DOWN button.
To modify the pre-set temperature
Adjust the desired cooling temperature by pressing the UP or DOWN buttons. Each
depression of the buttons will scroll through the available temperature settings in
increments of 1 degree Celsius. The temperature setting can be adjusted from 6�
to 18�.
To view the “set” temperature, press and hold the UP or DOWN buttons, the “set”
temperature will temporarily “flash” in the LED display for 5 seconds.
User Manual
12
V40DG2EBK AL-V40DG2E
WINE SERVING TEMPERATURE CHART
All wines mature at the same temperature, which is a constant temperature set between
12ºC to 14ºC. The below chart is an indicative temperature chart to indicate the best
temperature for drinking purposes.
Champagne NV, Sparkling, Spumante
6ºC
Dry White Semillon, Sauvignon Blanc
8ºC
Champagne Vintage,
10ºC
Dry White Chardonnay
10ºC
Dry White Gewürztraminer, Riesling, Pinot grigio
10ºC
Sweet White Sauternes, Barsac, Montbazillac, Ice Wine, Late Harvest
10ºC
Beaujolais
13ºC
Sweet White Vintage: Sauternes…
14ºC
White Vintage Chardonnay
14ºC
Red Pinot Noir,
16ºC
Red Grenache, Syrah
16ºC
Red Vintage Pinot Noir
18ºC
Cabernet & Merlot: French, Australian, New Zealand,
20ºC
Chilean, Italian, Spanish, Californian, Argentinean…
Vintage Bordeaux …
Room temperature not exceeding 20ºC
User Manual
V40DG2EBK AL-V40DG2E
13
IMPORTANT INFORMATION ABOUT TEMPERATURE
Your VINTEC wine cellar has been designed to guarantee optimum conditions for storing
and/or serving your wines.
Fine wines require long and gentle developments and need specific conditions in which to
reach their full potential.
All wines mature at the same temperature, which is a constant temperature set between
12ºC to 14ºC. Only the temperature of “dégustation” (wine appreciation) varies according
to the type of wines (see “Wine Serving Temperature Chart” above). This being said and
as it is for natural cellars used by wine producers for long period of storage, it is not the
exact temperature that is important, but its consistency. In other words, as long as the
temperature of your wine cellar is constant (between 12ºC to 14ºC) your wines will be
stored in perfect conditions.
Not all wines will improve over the years. Some should be consumed at an early stage (2
to 3 years) while others have tremendous ageing capability (50 and over). All wines have a
peak in maturity. Do check with your wine merchant to get the relevant information.
DEFROSTING/CONDENSATION/ HYGROMETRY/ VENTILATION
Your wine cellar is designed with “Auto-cycle” defrost system. During “Off-cycle” the
refrigerated surfaces of the wine cellar defrost automatically. Defrost water from the wine
cellar storage compartment drains automatically and part of it goes into a drainage
container, which is located at the back of the wine cellar next to the compressor. The heat
is transferred from the compressor and evaporates any condensation that has collected in
the pan. Part of the remaining water is collected within the wine cellar for humidity
purposes.
This system enables the creation of the correct humidity level inside your wine cellar
required by the natural cork to maintain a long lasting seal.
Notes: The water collected by condensation, is therefore recycled. Under extremely dry
environmental conditions, you may have to add some water into the water container
provided with your wine cellar.
All units are equipped with a double glazed glass door that has a third internal acrylic
layer to minimize condensation on the glass door.
The wine cellar is not totally sealed; fresh air admission is permitted through the
drainpipe. Air is circulated through the cellar by means of a fan/fans and the hollow
shelves.
User Manual
14
V40DG2EBK AL-V40DG2E
Notes: During the refrigerating cycle, heat is given off and disperses through the external
surfaces of the wine cellar. Avoid touching the surfaces during those cycles.
ADJUSTABLE WOODEN SHELVES
Adjusting/removing the shelves
For easy access to the storage content, you must pull the shelves approximately 1/3 of its
depth out of the rail compartment. These wine cabinets, however, are designed with a
notch on each side of the shelf tracks to prevent bottles from falling.
When removing any of these shelves out of the rail compartment, tilt the shelf as per the
diagram and simply pull out, or push in the shelf until it sits on the support
brackets securely.
REVERSIBILITY OF THE DOOR
Warning: To avoid accidents during the process of changing the door, we recommend that
you get assistance. The glass door is heavy and may cause injury if dropped.
- Depending on to the model and the type of handle your wine cabinet is equipped with,
you may have to rotate the door through 180 degrees.
- Depending on the type of handle your wine cabinet is equipped with, the door may not
be reversible or may require that a left or right opening door be ordered to change the
opening side.
User Manual
V40DG2EBK AL-V40DG2E
15
V40 S3/BK models
1. Lower hinge (right)
4. Door
7. Top hinge (left)
10. Door limit device
2 . Screws
5. Top hinge (right)
8. Hole cover
11. Screw
3 .Door axis
6. Hinge screws
9. Lower hinge (left)
1. Open the door to a 90 degrees angle, take out the 2 screws (2) from lower door axis (3),
remove the door (4), Remove the axis plate (3) from the door, (Fig. A).
2. Unscrew the screw (11) located underneath the doorframe and the limit device (10),
and relocate it at left end side of the door frame. (Fig. A/B)
3. Take out the 3 hinge screws (6) from the top hinge (right) (5) and remove it. (Fig. C)
4. Remove decorative nail (8) from left top of cabinet and install spare top hinge (Left)
(7) at left top of cabinet with 3 screws. (Fig. D)
5. Following the above procedure, install the spare lower hinge to the left (9). (Fig. E)
6. Install and aligned the door.
7. Insert the plastic caps to cover the holes(8).
User Manual
16
V40DG2EBK AL-V40DG2E
OPERATION ANOMALIES
Ensure that there is power to the electrical supply plug by connecting another electrical
appliance to it. Check fuse, if any. Make sure that the door is closed properly.
If your wine cellar appears to be malfunctioning, unplug it and contact your VINTEC’s
after sales service. Any intervention on the cold circuit should be performed by a
refrigeration technician who should carry out an inspection of the circuit sealing system.
Similarly, any intervention on the electrical circuit should be performed by a qualified
electrician.
Notes : Any intervention performed by a non- authorized technician by Vintec will lead to
the warranty being considered as null and void.
POWER FAILURES
In the event of a power interruption, all previous temperature settings are automatically
erased and it will revert to a preset temperature setting. (see preset chart)
Most power failures are corrected within a short period of time. An hour or two’s loss of
power will not affect wine cellar’s temperatures. To avoid sudden change of temperature
while the power is off, you should avoid opening the door. For longer period of power
failure, do take steps to protect your wine.
Irrespective of the cause, if you notice either abnormal temperature or humidity
levels inside your wine cellar, be reassured that only long and frequent exposure to
these abnormal conditions can cause a detrimental effect on your wines.
User Manual
V40DG2EBK AL-V40DG2E
17
TROUBLESHOOTING GUIDE
Common problems may easily be solved, saving you the cost of a possible service call.
Please read carefully the instruction manual and revert to troubleshooting guide chart.
PROBLEM
Wine cellar does not operate.
Wine cellar is not cold enough.
Turns on and off frequently.
The light does not work.
Vibrations.
The Wine cellar seems to make too
much noise.
The door will not close properly.
POSSIBLE CAUSE
Not plugged in.
The appliance is turned off.
The circuit breaker tripped or the fuse is broken.
Check the temperature control setting.
External environment may require a higher setting.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
The room temperature is hotter than normal.
A large amount of contents has been added to the
Wine cellar.
The door is opened too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
Not plugged in.
The circuit breaker tripped or a blown fuse.
The bulb is out of order.
The light button is “OFF”.
Check to assure that the Wine cellar is level.
The rattling noise may come from the flow of the
refrigerant, which is normal.
As each cycle ends, you may hear gurgling sounds
caused by the flow of refrigerant in your Wine
cellar.
Contraction and expansion of the inside walls may
cause popping and crackling noises.
The Wine cellar is not level.
The Wine cellar is not level.
The door was reversed and not properly installed.
The gasket is faulty. ( magnet or rubber is spoiled)
The shelves are out of position.
User Manual
18
V40DG2EBK AL-V40DG2E
Warranty
FOR SALES IN AUSTRALIA AND NEW ZEALAND
APPLIANCE: ALL VINTEC/TRANSTHERM
This document sets out the terms and conditions of the product
warranties for Vintec/Transtherm Appliances. It is an important
document. Please keep it with your proof of purchase documents
in a safe place for future reference should there be a manufacturing
defect in your Appliance. This warranty is in addition to other rights
you may have under the Australian Consumer Law.
(c) cosmetic damage which does not affect the operation of the
Appliance;
(d) damage to the Appliance caused by:
(i) negligence or accident;
(ii) misuse or abuse, including failure to properly maintain or service;
(iii) improper, negligent or faulty servicing or repair works done by
anyone other than an Electrolux authorised repairer or ASC;
1. In this warranty:
(a) ‘ACL’ or ‘Australian Consumer Law’ means Schedule 2 to the
Competition and Consumer Act 2010;
(iv) normal wear and tear;
(v) power surges, electrical storm damage or incorrect power supply;
(b) ‘Appliance’ means any Electrolux product purchased by you and
accompanied by this document;
(vi) incomplete or improper installation;
(vii) incorrect, improper or inappropriate operation;
(c) ‘ASC’ means Electrolux’s authorised serviced centres;
(d) ‘Vintec/Transtherm’ is the brand controlled by Electrolux Home Products
Pty Ltd of 163 O’Riordan Street, Mascot NSW 2020, ABN 51 004
762 341 in respect of Appliances purchased in Australia and Electrolux
(NZ) Limited (collectively “Electrolux”) of 3-5 Niall Burgess Road, Mount
Wellington, in respect of Appliances purchased in New Zealand;
(e) ‘Warranty Period’ means the period specified in clause 3 of this
warranty;
(f) ‘you’ means the purchaser of the Appliance not having purchased
the Appliance for re-sale, and ‘your’ has a corresponding meaning.
2. Application: This warranty only applies to new Appliances, purchased
and used in Australia or New Zealand and is in addition to (and does not
exclude, restrict, or modify in any way) other rights and remedies under
a law to which the Appliances or services relate, including any nonexcludable statutory guarantees in Australia and New Zealand.
3. Warranty Period: Subject to these terms and conditions, this warranty
continues for in Australia for a period of 24 months and in New Zealand
for a period of 24 months, following the date of original purchase of the
Appliance.
4. Repair or replace warranty: During the Warranty Period, Electrolux
or its ASC will, at no extra charge if your Appliance is readily accessible
for service, without special equipment and subject to these terms and
conditions, repair or replace any parts which it considers to be defective.
Electrolux may, in its absolute discretion, choose whether the remedy
offered for a valid warranty claim is repair or replacement. Electrolux or its
ASC may use refurbished parts to repair your Appliance. You agree that
any replaced Appliances or parts become the property of Electrolux.
5. Travel and transportation costs: Subject to clause 7, Electrolux will
bear the reasonable cost of transportation, travel and delivery of the
Appliance to and from Electrolux or its ASC. Travel and transportation will
be arranged by Electrolux as part of any valid warranty claim.
6. Proof of purchase is required before you can make a claim under this
warranty.
7. Exclusions: You may not make a claim under this warranty unless the
defect claimed is due to faulty or defective parts or workmanship. This
warranty does not cover:
(a) light globes, batteries, filters or similar perishable parts;
(b) parts and Appliances not supplied by Electrolux;
(viii) insect or vermin infestation;
(ix) failure to comply with any additional instructions supplied with
the Appliance;
In addition, Electrolux is not liable under this warranty if:
(a) the Appliance has been, or Electrolux reasonably believes that the
Appliance has been, used for purposes other than those for which
the Appliance was intended, including where the Appliance has
been used for any non-domestic purpose;
(b) the Appliance is modified without authority from Electrolux in writing;
(c) the Appliance’s serial number or warranty seal has been removed
or defaced.
8. How to claim under this warranty: To enquire about claiming under
this warranty, please follow these steps:
(a) carefully check the operating instructions, user manual and the
terms of this warranty;
(b) have the model and serial number of the Appliance available;
(c) have the proof of purchase (e.g. an invoice) available;
(d) telephone the numbers shown below.
9. Australia: For Appliances and services provided by Electrolux in
Australia: Electrolux goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to
have the Appliance repaired or replaced if the Appliance fails to be of
acceptable quality and the failure does not amount to a major failure.
‘Acceptable quality’ and ‘major failure’ have the same meaning as
referred to in the ACL.
10. New Zealand: For Appliances and services provided by Electrolux
in New Zealand, the Appliances come with a guarantee by Electrolux
pursuant to the provisions of the Consumer Guarantees Act, the Sale
of Goods Act and the Fair Trading Act. Where the Appliance was
purchased in New Zealand for commercial purposes the Consumer
Guarantee Act does not apply.
11. Confidentiality: You accept that if you make a warranty claim, Electrolux
and its agents including ASC may exchange information in relation to you
to enable Electrolux to meet its obligations under this warranty.
Important Notice
Before calling for service, please ensure that the steps listed in clause 8 above have been followed.
FOR SERVICE
or to find the address of your nearest
authorised service centre in Australia
PLEASE CALL 1800 771 776
For the cost of a local call (Australia only)
FOR SERVICE
or to find the address of your nearest
authorised service centre in New Zealand
PLEASE CALL 0800 550 020
(New Zealand only)
ALL_Vintec_Transtherm_May17
AUSTRALIA
ELECTROLUX HOME PRODUCTS
163 O’Riordan Street, Mascot NSW 2020
vintec.com.au
FOR ACCESSORIES
PLEASE CALL 1800 666 778
For the cost of a local call (Australia only)
or visit www.vintecclub.com
ELECTROLUX (NZ) Limited
NEW ZEALAND
FOR ACCESSORIES
PLEASE CALL 0800 550 020
3-5 Niall Burgess Road, Mount Wellington
or visit www.vintecclub.com
vintec.co.nz
(New Zealand only
Service and support
In the rare event that your Vintec cabinet does not perform
to your satisfaction, contact our dedicated support team:
1800 771 776
[email protected]
Vintec. We are part of the
Electrolux Family. To add
a touch of professional
inspiration to your home,
visit electrolux.com.au
Stay in touch and share your
user experience by following us:
@vintecclub
© 2018 Electrolux Home Products Pty Ltd. ABN 51 004 762 341
VMAN_V40s_DG2E_ Jun18
vintec.com