advertisement
▼
Scroll to page 2
of 40
Please read this owner's manual operating carefully before the Monitor. Retain it for future reference. Record model number and serial number of the Monitor. See the label attached on the back of the Monitor and quote this information to your dealer when you require service. Model number Serial number : : ON/OFF PLASMONITR MZ-42PZ10/B/G/K/S MT-42PZ10/B/G/K/S OWNER'S MANUAL INPUT SELECT VOLUME LG Plasma Monitor What is Plasma Monitor? a If voltage is inputted to gas in glass panels, ultraviolet rays is outputted and fused with a fluorescent substance. At this moment, light is emitted. A Plasma Monitor is a next generation flat Display using this phenomenon. 160° - Wide angle range of vision A Plasma Monitor provides more than 160° angle range of vision picture without distortion from any direction. Easy that you can get a installation A Plasma Monitor is much lighter and smaller than other can install the Plasma Monitor at the desired place. Big so same class products so that you screen The screen of in a theatre. a Plasma Monitor is 42" so that you can get vivid experience as if you are Multimedia Plasma Monitor A Plasma Monitor can be connected with for conference, game, internet and so on. The explanation a computer so that you can use about coloured dots may be present on it as a screen PDP screen The PDP which is the display device of this product is composed of 0.9 to 2.2 million cells and a few cell defects can occur in the manufacture of the PDP. Several coloured dots visible on the screen would be acceptable, in line with other PDP manufacturers and would not mean that the PDP is faulty. We hope you will understand that the product which corresponds to this standard is regarded as acceptable. It means that it could not be changed or refunded. We promise that we'll do our best to develop our technology to minimize the cell defects. WARNING This is Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. WARNING TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. ON/OFF INPUT SELECT VOLUME Contents First step Instructions ....................................................4 Safety Composition Controls of the Monitor .............................................8 Controls of the remote control ................................12 Installation of the Monitor .......................................14 Connection Watching VCR ........................................................16 Watching Cable TV.................................................17 Watching external AV source..................................18 Watching DVD ........................................................19 Connecting PC .......................................................20 Function checking in PC mode ..............................22 Adjusting in PC mode .............................................23 Using the remote control ........................................26 Basic function Turning on the Monitor ...........................................27 Selecting the on screen language ..........................28 Function checking...................................................29 Picture Picture adjustment..................................................30 Picture format .........................................................31 Sound Sound adjustment...................................................32 function Child lock ................................................................33 Auto sleep...............................................................34 Sleep timer .............................................................35 Special Others Troubleshooting check list ......................................36 Product specifications.............................................39 Safety - Instructions Use the Monitor at the place lower than the altitude of 6562 feet the best quality of picture and sound. WARNING Indorstali This may cause a to get NOTES Do not place the Monitor in direct sunlight or near heat sources such as heat registers, stove and so on. - (2000m) This Plasma display is designed to be mounted horizontally (wide viewing). fire. WARNING Do not the Monitor in such as a bathany place where it use damp place room or OutdorInsali is likely to get wet. - This may cause a fire or could give an electric shock. - Bend antenna cable between inside and outside building to prevent rain from flowing in. This may cause water damaged inside the Monitor and could give an electric shock. WARNING NOTES Earth wire should be connected. - - Power - If the earth wire is not connected, there is possible a danger of electric shock caused by the current leakage. If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician. Do not connect ground to telephone wires, lightning rods or gas pipe. Short-circuit breaker 4 Never touch the power with a wet hand - This may cause an plug electric shock. * Safety instructions have two kinds of WARNING NOTES information, and each meaning of it is below. as The violation of this instruction may cause serious The violation of this instruction may cause light injuries injuries or and even damage First ep death. of the product. Take care of danger that may happen NOTES under specific condition. Compsiton NOTES Do not place the Monitor in built-in installation such as a bookcase or rack. Disconnect from the mains and remove all connections before moving. a Ventilation - required. When installing the Monitor on a table, be careful not to place the edge of its stand. This may cause the Monitor to fall, causing serious injury to a child or adult, and serious damage to the Monitor. - NOTES Do not place an outside antenna in the vicinity of overhead power lines other electric light or power circuits. - This may cause an electric shock. or There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls. - ConectiBasfu Picture This may cause an electric shock. Sound NOTES Do not pull the cord but the when unplugging. plug - This may cause a fire. Ensure the power cord doesn't trail across any hot objects like a heater. - This may cause tric shock. a fire or an elec- Specialfunto Do not plug when the power cord or the plug is damaged or the connecting part of the power outlet is loose. - This may cause a fire an electric shock. or Others 5 Safety Instructions WARNING Do not place anything containing liquid on top of the Monitor. - Using Do not insert any the exhaust vent. - This may cause a fire or could give an electric shock. object This may cause a fire an electric shock. or into could give WARNING Do not use water the Monitor while cleaning. - Cleanig This may cause damaged the Monitor or could give an electric shock. In case of smoke or strange smell from the Monitor, switch it off ,unplug it from the wall outlet and contact your dealer or service center. - This may cause a fire an electric shock. or could give WARNING Do not attempt to service the Monitor yourself. Contact your dealer or service center. Others 6 - This may cause damaged the Monitor or could give an electric shock. During unplug a lightning thunder, the Monitor from the wall outlet and don't touch an antenna cable. - This may cause damaged the Monitor or could give an electric shock. WARNING in U.K. * This set is only with a BS 1363 approved 13 amp mains plug, fused at 13 amp. When replacing the fuse always use a 13 amp BS 1362, BSI or ASTA approved type. Never use this plug with the fuse cover omitted. To obtain a replacement fuse cover contact your dealer or "LG Electronics U.K. Ltd." If the type of plug supplied is not suitable for the mains sockets in your home, then the plug should be removed and a suitable type fitted. A mains plug removed from the mains lead of this set must be destroyed. A mains plug with bared wires is hazardous if inserted in a mains socket. Do not connect either wire to the earth pin, marked with the letter E or with the earth symbol or coloured green or green and yellow. If any other plug is fitted, use a 13 amp fuse, either in the plug, or at the distribution board. The wires in this mains lead are coloured in accordance with the following codes: BLUE: NEUTRAL, BROWN: LIVE As the colours of the wires in the mains lead of this set may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. supplied WARNING Do not place heavy the Monitor. Compsiton NOTES Dispose of used batteries carefully to protect a child from eating them. objects on - First ep This may cause serious a child or adult. injury to - In case to see a that it eats them, take it doctor immediately. When moving the Monitor assembled with the Speakers do not carry holding the Speakers. - This may cause the Monitor to fall, causing serious injury child or adult, and to ConectiBasfu a serious damage to the Monitor. NOTES Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. - This may cause damaged the Monitor an electric shock. or could Contact the service center once a year to clean the internal part of the Monitor. - Accumulated dust can cause Picture mechanical failure. give Sound NOTES The distance between eyes and the screen should be about5~7timesaslongas diagonal length of the screen. - If not, eyes will strain. Unplug the Monitor from the wall outlet when it is left unattended and unused for long periods of time. - Accumulated dust may cause fire or an electric shock from deterioration or electric leakage. a Only use the specified bat- teries. - This make cause damaged the remote control or could give an electric shock. Specialfunto Others 7 Controls of the Monitor <Front Panel> ON/OFF INPUT SELECT ON/OFF VOLUME MAIN POWER BUTTON REMOTE CONTROL SENSOR INPUT SELECT VOLUME INPUT SELECT BUTTON POWER/STANDBY INDICATOR Illuminates red in standby Illuminates green when the Monitor is switched POWER BUTTON on VOLUME (Φ,Γ) BUTTON 8 First ep Compsiton <Back Panel> (+) R () () L COMPONENT (480i/480p) (DVD INPUT) AV INPUT EXTERNAL SPEAKER RL AUDIO <MONO> VIDEO (+) Y PB RGB INPUT(VGA/SVGA/XGA) PR AUDIO INPUT R CONTROL ConectiBasfu AC INPUT L Picture (+) R () () L COMPONENT AV INPUT EXTERNAL SPEAKER (+) R AUDIO L Y R AUDIO L (MONO) (480i/480p) (DVD INPUT) Y (MONO) VIDEO VIDEO AV INPUT PB RGB PR PB P AUDIO INPUT R CONTROL Sound AC INPUT L R COMPONENT (480i/480p) (DVD INPUT) EXTERNAL AV INPUT / SPEAKER (8Ω) KNOBS COMPONENT (480i/480p) DVD INPUT SOCKETS Γ The Interface board is not equipped MZ-42PZ10 series model. (AP-42EA20) INPUT(VGA/SVGA/XGA) on RGB INPUT (VGA/SVGA/XGA) / AUDIO INPUT / CONTROL SOCKET POWER INPUT SOCKET This Monitor operates on an AC mains supply, the voltage is as indicated as inside back cover of this manual. Never apply DC power to the Monitor. 9 Specialfunto Others Accessories POWER MULTIMEDIA TV/AV ARC I/II PIP TEXT PR- PR+ SWAP MENU VOL INPUT PR MUTE OK VOL PR 1 4 7 PSM POSTION cable Power cord MIX SLEEP P/STILL PLAY ? LIST REC FF Remote control Alkaline batteries Phone scart cable (Optional) (Optional) Extras Optional Optional extras can be changed or modified optional extras can be added. Contract your dealer for buying these items. ON/OFF M 1.5V Owner's Manual - SSM STILL REVEAL 1.5V LG TV ASmark - 6 9 0 TIME REW pin 3 5 8 SIZE STOP D-sub 15 2 STROBE/ MULTIMEDIA TV/VIDEO MENU ENTER VOL for without any notification quality improvement PR CH PB Y AUDIO RL (MONO) VIDEO (480/480p) COMPONENT INPUT) (DVD AV INPUT RZ-BA10 (PDP Tuner) AP-42WA20M series (Tilt 10 wall mounting bracket) AP-42EA20 (Interface board) AP-42WA10 series (Wall mounting bracket) new Optional - - First ep Extras Optional extras can be changed or modified optional extras can be added. Contract your dealer for buying these items. for quality improvement without any notification AP-42CA10 series AP-42FA10 series (Ceiling mounting bracket) (Floor type stand) AP-42DA10 series AP-42SA10 series (Desktop stand) (Speakers) new Compsiton ConectiBasfu Picture Sound AP-42SA10D series AP-42SA10F series (Speaker stand) (Floor type speaker stand) Specialfunto Others Video cables Audio cables 11 Controls of the remote control - - Some buttons on this remote control does function only when the Monitor is nected with RT/RZ-BA10 (the PDP tuner). When using the remote control aim it at the remote control sensor of the Monitor. con- POWER POWER button MULTIMEDIA TV/AV ARC I/II PIP TEXT MULTIMEDIA button ARC button (Refer to p.31) No function PR- No function PR+ SWAP MENU INPUT PR MUTE MENU button OK button VOL OK VOL VOLUME (Φ, Γ) buttons PR 1 2 3 4 5 6 7 8 9 PSM 0 SSM No function PSM button (Refer to p.30) POSITION STROBE/ STILL SIZE TIME REVEAL MIX STOP VCR buttons controls a LG video cassette recorder. 12 REW SLEEP M P/STILL PLAY LIST REC FF ? First ep TV/AV button on Compsiton the remote control Each press of this button the mode as below. changes TV/AV button When the Interface board AV No function (not supplied) is installed. Γ The Interface board No function (AP-42EA20) is not equipped on MZ-42PZ10 series model. RGB-PC MUTE button switches the sound on or COMPONENT off. MULTIMEDIA button on the remote control Ε / Δ Each press of this button the mode as below. buttons changes RGB-PC ConectiBasfu Picture COMPONENT SSM button (Refer to p.32) Sound No function SLEEP button (Refer to p.35) Specialfunto Others 13 Installation of the Monitor - The Monitor can be installed in various ways such desktop type, To install as wall INPUT SELECT MUTIMDA N/OFF The monitor can be installed on further information, refer to (For mounting type, mounting type ON/OFF ? wall as etc.. the wall '(Tilt) TVAV MNU VOL PR picture above. mounting bracket owner's manual'.) as wall OK VOLUME the Tips ? Install this monitor only in a location where a. (Wall adequate ventilation is available. 4inch mount minimum 1.18inch allowable clearances for adequate ventilation) 4inch 4inch 4inch 14 First ep To install as Compsiton desktop type INPUT SELECT ON/OFF ConectiBasfu VOLUME Picture ? The monitor (For on the desk as further information, refer to 'Desktop stand owner's can be installed the picture Sound above. manual'.) Specialfunto b. 4inch mount minimum allowable clearances for (Pedestal 1.18inch adequate ventilation) 4inch 4inch Others 2.36inch 15 Watching VCR - When - - - connecting yellow, Audio(L) the Monitor with external (+) () L R () R (+) R AUDIO L L Y PB COMPONENT RGBINPUT(VGA/SVGAXGA) AUDIO NPUT R PR (480i/480p) PB PB P (L) (VGA/SVGA/XGA) AUDIO INPUT R CONTROL L R COMPONENT (480i/480p) (DVD INPUT) <Back AUDIO of time. Typically a frozen still picfixed image may remain visible on VIDEO PUT OUT (R) of the AC INPUT PR Back S-VIDEO CONTROL AUDIO(L/MONO) input L RGB INPUT (DVD INPUT) Y (MONO) VIDEO (MONO) AV (480i/480p) (DVDINPUT) RL AUDO <MONO>VIDEO Y AUDIO COMPONENT AV INPUT () L (+) AV INPUT EXTERNAL SPEAKER () cable from the VCR to the image remain on the screen for a long period picture format or if a CH label is present; the EXTERNAL SPEAKER R connecting ports (Video - If you have a Monitor. Avoid having a fixed ture from a VCR, 4:3 the screen. (+) match the colours of equipments, white, Audio(R) red). mono VCR, connect the audio - of the Monitor panel panel of VCR> VIDEO IN To watch VCR Γ The Interface board 1 2 (When the Interface board is installed.) (AP-42EA20) is not equipped on MZ-42PZ10 series model. Press TV/AV button on the remote control to select AV. (Select AV if AV INPUT is connected.) TV/AV Insert a video tape into the VCR and press the PLAY button on the VCR. Tips ? 16 To prevent picture noise, place the VCR more than 50cm away from the Monitor. Watching Cable - After subscribing for cable TV. a First ep TV local cable TV station and installing a converter you can watch Compsiton R (+)() (+) R () () L () L (+) R (+) R AUDIO AUDIO L L (MONO) PUT Y PB RGBINPUT (VGA/SVGA/XGA) Y VIDEO (480i/480p) PB AUDIO NPUT R PR PB CONTROL AC INPUT L RGB INPUT (VGA/SVGA/XGA) PR P AUDIO INPUT R ConectiBasfu CONTROL L R COMPONENT (480i/480p) (DVD INPUT) Back UDI Y (DVD INPUT) (MONO) VIDEO AV (480i/480p) (DVDINPUT) RL AUDIO <MONO> VIDEO COMPONENT AV INPUT EXTERNAL SPEAKER COMPONENT AV INPUT EXTERNAL SPEAKER panel of the Monitor Picture VO <Cable box> TV VCR RF Cable Sound To watch cable TV (When the Γ The Interface board 1 2 (AP-42EA20) Press TV/AV button on is not Interface board is equipped on the remote control to select AV. (Select AV if AV INPUT is installed.) MZ-42PZ10 series model. Specialfunto TV/AV connected.) Select your desired programme with the remote control for cable box. Others Tips ? For further information of cable TV, contact the local cable TV station. 17 external AV Watching - When connting the connecting ports. Monitor with external AV INPUT EXTERNAL SPEAKER (+) R () () L () () L (+) (+) R R AUDIO L RL AUDIO L AV (MONO) VIDEO (MONO) COMPONENT VIDEO (480i/480p) (DVD INPUT) Y PB Y RGB INPUT(VGA/SVGA/XGA) (480i/480p) PB AUDO INPUT R PR PB match the colours of equipments, (DVD INPUT) Y AUDIO <MONO> COMPONENT AV INPUT EXTERNAL SPEAKER (+) R CONTROL source AC INPUT L RGB INPUT AUDIO INPUT (VGA/SVGA/XGA) PR R CONTROL L PR VIDEO COMPONENT (480i/480p) (DVD INPUT) PUT Camcorder R AUDIO VIDEO Video game set To watch external AV source (When the Interface board is installed.) Γ The Interface board 1 Press TV/AV button AV. 2 Operate 18 (AP-42EA20) the on is not equipped on MZ-42PZ10 series model. the remote control to select corresponding external equipment. TV/AV How to connect (When Γ The Interface board ? ? First ep DVD Watching the Interface board is is not (AP-42EA20) equipped DVD input is set as 480i/480p mode. Connect DVD video inputs to Y, PB, PR of COMPONENT audio inputs to Audio sockets of AV INPUT. (+) R () L () () () R (+) AUDIO L L (MONO) PB (480i/480p) C MPONENT (4 (DVD INP CONTROL (480i/480p) (DVD INPUT) Compsiton and ConectiBasfu AC INPUT L RGB INPUT AUDIO INPUT (VGA/SVGA/XGA) PR R CONTROL L PR PB VIDEO PUT AUDOINPUT R PR PB Y L AV Y (DVD INPUT) Y (MONO) VIDEO R AUDIO RGBINPUT(VGA/SVGAXGA) (480i/480p) (DVDINPUT) RL AUDO <MONO>VIDEO (+) COMPONENT AV INPUT EXTERNAL SPEAKER (+) R COMPONENT AV INPUT EXTERNAL SPEAKER installed.) MZ-42PZ10 series model. on i/480p) ) Picture < Back panel of the Monitor> Sound (R) < AUDIO (L) Back panel of a DVD player> ? How to (When the Interface board is installed.) Γ The Interface board Component Input ports can get better picture quality if you connect DVD player with component input You use (AP-42EA20) is not equipped on ports as below. MZ-42PZ10 series model. Component ports of the Monitor ? ? Press MULTIMEDIA or TV/AV button on the remote control to select COMPONENT. Try this after turning on the DVD player. Video output ports of DVD player Specialfunto YPBPR Y Y Y Pb B-Y Cb Pr R-Y Cr 19 Others PC Connecting - You can vivid enjoy picture and sound with connecting a PC with the Monitor. How to connect ? ? ? ? ? Set the video mode of PC to VGA/SVGA/XGA to obtain the best picture quality for the Monitor. If the resolution of PC is over XGA, there will be no picture on the Monitor. Connect the signal cable from the monitor output port of the PC to the RGB INPUT(VGA/SVGA/XGA) port of the Monitor. Connect the audio cable from the PC to the Audio ports of the Monitor. (Audio cables not included with the Monitor) In case of using a sound card adjust PC sound properly. (+) R () () L () () L (+) (+) R AUDIO L AUDIO L (MONO) Back How to panel PB RGB INPUT(VGA/SVGA/XGA) AUDOINPUT R PR (480i/480p) CONTROL AC INPUT L RGB INPUT (VGA/SVGA/XGA) PR PB PB AUDIO INPUT R CONTROL L PR VIDEO AV INPUT < Y (DVD INPUT) Y (MONO) VIDEO Y R (480/480p) (DVD INPUT) RL AUDO <MONO>VIDEO COMPONENT AV INPUT EXTERNAL SPEAKER (+) R COMPONENT AV INPUT EXTERNAL SPEAKER COMPONENT (480i/480p) (DVD INPUT) of the Monitor> use MULTIMEDIA TV/AV ? Press POWER button on the PC and press ON/OFF button the Monitor. After this press button on the Monitor or press POWER button on the remote control. Press MULTIMEDIA or TV/AV button on the remote control to select RGB-PC. Set the resolution of PC under XGA (1024x768). on ? <On the remote control> ? (Refer to page 21.) Tips ? ? ? 20 If still picture is on the screen for a long period time, Screen Burn ! If the resolution of PC is over XGA, connect to the RGB INPUT(VGA/SVGA/XGA) port of the Monitor after changing the resolution of PC under XGA. If picture isn't be displayed properly by conneting a non-standard PC, contact your dealer for more information. First ep Displayable Resolution Monitor Horizontal Specification Vertical Frequency (KHz) Frequency (Hz) 640x400 37.861 85.08 720x400 31.469 70.08 31.469 59.94 35.000 66.66 37.861 72.80 37.500 75.00 43.269 85.00 35.156 56.25 37.879 60.31 48.077 72.18 46.875 75.00 53.674 85.06 832x624 49.725 74.55 1024x768 48.363 60.004 (Compressed XGA) 56.476 70.069 60.023 75.029 640x480 (VGA) 800x600 (SVGA) Compsiton ConectiBasfu Picture Sound Specialfunto Others 21 Function - Make sure to select RGB-PC before 1 MENU in PC mode checking operating. the MENU button. Repeatedly press ' Contrast 100 Ω Brightness 55 · Colour 50 ≥ 60 Sharpness ? Tint ΔΕ ΦΓ 0 OK <Picture Clock MENU TV/AV menu> 0 Equalizer 0 Balance Flat 0 15 phase Auto-configure Reset ΔΕ ΦΓ OK MENU <Special PR 2 ΔΕ Δ The selected / Ε VOL 3 OK button to select menu PR VOL Press the Φ / item. ΦΓ OK MENU <Sound menu> Press the ? TV/AV Γ item changes button to TV/AV menu> a menu item. from white to purple. change the setting of a menu ? Press the TV/AV button to exit. Tips when Equalizer is set to User, Treble and Bass are displayed and be adjusted. Language is displayed only in PC mode (special menu) when the Interface board is not installed and you can select your desired Language. ΓThe Interface board (AP-42EA20) is not equipped on MZ-42PZ10 series model. ? Only can ? 22 Auto - configure This function is for the automatic 1 First ep in PC mode Adjusting adjustment Repeatedly press the MENU special menu. of the screen position and clock Compsiton phase. button to select the 0 0 Clock 15 phase Auto-configure ConectiBasfu Reset MENU ΔΕ 2 Press the ΦΓ OK MENU TV/AV / Ε button to select Autoand then press the Φ / Γ Δ configure button. 0 0 Clock 15 phase Auto-configure Picture Reset PR VOL VOL ΔΕ ΦΓ OK MENU TV/AV PR Sound 3 Press the OK button. Specialfunto OK ? If picture Monitor's needs to be position adjusted more after auto adjustment, adjust your phase manually. and clock Others 23 in PC mode Adjusting Adjusting 1 horizontal / vertical Repeatedly press the MENU special menu. postion button to select the 0 0 Clock 15 phase Auto-configure Reset MENU ΔΕ 2 PresstheΔ/Εbuttontoselect or MENU TV/AV 0 0 Clock VOL VOL ? ? Select Select 15 phase Auto-configure Reset ΔΕ PR ΦΓ OK MENU TV/AV for horizontal position adjustment. for vertical position adjustment. Press the Φ / Γ button to adjust until you get desired horizontal vertical position and then press the OK button. OK VOL 24 OK . PR 3 ΦΓ VOL or First ep clock Adjusting ? 1 In case that picture isn't adjust phase manually. phase clear after auto adjustment Repeatedly press the MENU special menu. and especially that characters are Compsiton trembling, button to select the 0 0 Clock 15 phase Auto-configure Reset ConectiBasfu MENU ΔΕ 2 Press the Δ / Ε ΦΓ OK MENU TV/AV button to select Clock phase. 0 0 Clock 15 phase Auto-configure Reset PR ΔΕ ΦΓ OK MENU TV/AV Picture PR 3 Press the button. Φ / Γ button to adjust phase and then press the OK Sound OK VOL VOL Specialfunto Initializing ? To initialize the adjusted value, select Reset with the press the Φ / Γ button. Δ / Ε button and then Others 25 Using Inserting the remote control batteries ? the Open battery compartment cover on side and insert the batteries with correct ? Apply two 1.5V alkaline batteries of AAA Don't mix the used batteries with ? Notes for Make sure objects 26 using there are no between the new Install the batteries with the correct the back polarity. type. batteries. polarities. the remote control Don't place near a the remote control heater remote control and its Strong impact sensor. trol may damp place. or cause on the remote operation con- failure. Signal from the remote control may be disturbed by sun light or other strong light. In this case, turn the set to other direction. Turning - When using Turning aim it at its the Monitor just sensor on First ep the Monitor the Monitor. Compsiton after installation correctly. ConectiBasfu Press the ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby mode. Press the INPUT SELECT button on the Monitor or press the TV/AV, MULTIMEDIA button on the remote control and then the Monitor will be switched on. 2 , Turning 2 on control, Connect power cord 1 1 the remote on on the Monitor (power cord is still If the Monitor is turned off with the ? connected) button on the Monitor Press the INPUT SELECT button on the Monitor or press the TV/AV, MULTIMEDIA button on the remote control to turn on the Monitor. , If the Monitor is turned off with the ON/OFF button ? Press the ON/OFF button on the Monitor to turn on on Picture the Monitor the Monitor. Sound 3 If the Monitor is turned off with the remote control and also the ON/OFF button on the Monitor ? Press the ON/OFF button on the Monitor and then press the INPUT SELECT button on the Monitor or press the TV/AV, MULTIMEDIA button the remote control to turn on the Monitor. Specialfunto , Tips Adjusting Volume(Γ) ? volume level button increases the level of sound and decreases the level of sound. volume(Φ) on Others button 27 Selecting 1 the language on screen Repeatedly press the MENU special menu. button to select the Child lock Off Auto Off sleep Language MENU ΔΕ 2 Press the / Ε button to select Language and then press the OK but- ΦΓ OK MENU TV/AV Δ ton. PR Child lock Off Auto Off sleep Language OK ΔΕ ΦΓ OK MENU TV/AV PR 3 Press the Δ / Ε or Φ / Γ button to select the desired language. PR VOL VOL PR 4 Press the TV/AV button to exit. TV/AV Tips You can select your desired language only in AV mode (when the Interface board is installed) or PC mode (when the Interface board is not installed). ΓThe Interface board (AP-42EA20) is not equipped on MZ-42PZ10 series model. ? 28 Function 1 MENU checking First ep the MENU button. Compsiton Repeatedly press ' Contrast 100 Ω Brightness 55 · Colour 50 ≥ 60 Sharpness ? Tint ΔΕ ΦΓ 0 OK <Picture MENU menu> Child lock Off Equalizer Auto Off Balance sleep Language ΔΕ ΦΓ OK <Special MENU ConectiBasfu TV/AV TV/AV ΔΕ Flat 0 ΦΓ OK <Sound menu> MENU TV/AV Picture menu> PR 2 PR VOL VOL 3 Press the ? Δ The selected / Ε button to select menu Press the Φ / item. Γ item changes button to a menu item. from white to purple. change the setting of Sound a menu ? Specialfunto Press the TV/AV button to exit. Tips ? Only when Equalizer be adjusted. is set to User, Treble and Bass are displayed and can Others When the Interface board is installed, the special menu is displayed in AV/COMPONENT mode. ΓThe Interface board (AP-42EA20) is not equipped on MZ-42PZ10 series model. ? 29 Picture - You can adjustment adjust picture contrast, brightness, colour intensity, sharpness or NTSC input only) to the levels you prefer. and tint (COMPO- NENT, RGB-PC mode 1 Repeatedly press the MENU picture menu. button to select the ' Contrast 100 Ω Brightness 55 · Colour 50 ≥ 60 Sharpness ? Tint 0 MENU ΔΕ 2 Press the Δ / Ε button to select the desired picture item and then press the Φ / Γ button to make appropriate adjustments. ΦΓ OK MENU ' Contrast TV/AV 100 Ω Brightness 55 · Colour 50 ≥ 60 Sharpness ? Tint ΔΕ ΦΓ 0 OK MENU TV/AV PR VOL VOL PR 3 Press the OK button to store it for the picture User and then press the TV/AV button. ' Contrast Ω Brightness 100 55 · Colour 50 ≥ 60 Sharpness ? Tint 0 OK TV/AV ? preferred setting, press the PSM button until the desired pic(Dynamic, Standard, Mild or User) appears. The picture Dynamic, Standard and Mild are programmed for good picture reproduction at the factory and cannot be changed. To recall your ture 30 Stored First ep Picture format - - You can watch Plasma Display in various picture formats; 16:9 (Wide), 4:3 (Standard), Zoom1orZoom2inAVmode. Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR, 4:3 picture format or if a CH label is present; the fixed image may remain visible on the screen. ARC (Aspect Repeatedly press picture format. ARC ? Ratio Control) the ARC button to select your desired enjoy the cinema (the picture format of 16:9) general Plasma Display programme through the 16:9 mode. The screen 16:9 is viewed just like that but the 4:3 is magnified to the left and right so that the 16:9 is full. ? ? ? ConectiBasfu 16:9 You can or ? Compsiton 4:3 This picture format is 4 to 3 of general Plasma screen screen Display. Zoom1 You can enjoy the cinema in a vast screen through the Zoom mode. The screen 4:3 is magnified to the upper/lower sides so that the screen 16:9 is full. The bottom and top of the picture may be lost. You can move the screen up/down with Δ / Ε button. Picture Zoom2 You can enjoy a larger magnified screen in this mode. The screen Zoom 2 is viewed just like that but the screen 16:9 is magnified more and more to the left and right so that the screen Zoom 2 is full. Sound Zoom Only when receiving over SVGA (800X600), you can select Zoom. You can move the screen up/down or left/right with Δ/ΕorΦ/Γbutton. Specialfunto Tips ? ? ? Others When you switch the Monitor to standby or off, the picture format is reset to the 16:9. In COMPONENT mode only you can select 4:3. Only when receiving RGB-PC signal (over 800 x 600) in RGB-PC mode, you can select Zoom. 31 Sound - You can select your preferred sound treble and bass. adjustment setting; Flat, Music, Movie or Speech and you can adjust balance, 1 Repeatedly press the MENU button to select the sound menu. Flat Equalizer Balance 0 MENU ΔΕ 2 Press the Δ / Ε button to select the desired sound item and then press the Φ / Γ button to make desired adjust- ΦΓ OK MENU TV/AV Flat Equalizer Balance 0 ments. ? In case of Equalizer User, you can adjust ΔΕ ΦΓ OK MENU TV/AV Treble and Bass. PR VOL VOL User Equalizer Balance 0 Treble 50 Bass 50 PR ΔΕ ? 3 OK MENU TV/AV preferred setting, press the SSM button until the desired sound (Flat, Music, Movie, Speech or User) appears. The sound Flat, Music, Movie and Speech are programmed for good sound reproduction at the factory and cannot be changed. To recall your Press the TV/AV button to exit. TV/AV 32 ΦΓ also First ep Child lock - The Monitor can be set so that the remote control is needed to control it. This feature used to prevent unauthorized viewing. 1 Repeatedly press the MENU to select the special menu. can be Compsiton button Child lock Off Auto Off sleep Language MENU ΔΕ 2 Press the Δ / Ε button to select Child lock. ΦΓ OK MENU TV/AV Child lock Off Auto Off sleep Language ConectiBasfu PR ΔΕ ΦΓ OK MENU TV/AV PR 3 Press the Φ / Γ button to select On. Child lock On Auto Off sleep Language VOL VOL ΔΕ ΦΓ OK MENU TV/AV Sound With the lock on, the display Child lock on appears on the screen if any button on the Monitor is pressed while viewing the Plasma Display. ? 4 Picture Press the TV/AV button to exit. Specialfunto TV/AV Tips Others Child lock is displayed in AV/COMPONENT mode when the Interface board is installed. ΓThe Interface board (AP-42EA20) is not equipped on MZ-42PZ10 series model. ? 33 Auto - sleep If you select Auto sleep On, the Monitor will automatically switch itself to ten minutes after no input signal. standby mode approximately 1 Repeatedly press the MENU special menu. button to select the Child lock Off Auto Off sleep Language MENU ΔΕ Press the 2 Δ / Ε ΦΓ OK MENU TV/AV button to select Auto sleep. Child lock Off Auto Off sleep Language PR ΔΕ ΦΓ OK MENU TV/AV PR Press the Φ / Γ button to select On. 3 Child lock Off Auto On sleep Language VOL VOL ΔΕ ΦΓ OK MENU TV/AV Press the TV/AV button to exit. 4 TV/AV Tips Auto sleep is displayed in AV/COMPONENT mode when the Interface board is installed. ΓThe Interface board (AP-42EA20) is not equipped on MZ-42PZ10 series model. ? 34 Sleep - First ep timer You don't have to remember to switch the Monitor off before you go to sleep. The automatically switches the Monitor to standby after the preset time elapses. sleep timer Compsiton Press the SLEEP button to set sleep time. Each time you press this button setting time is changed as below. SLEEP --- 10 20 30 120 90 60 ConectiBasfu 240 180 --- Picture ? To release sleep time setting, press the SLEEP ---. button repeatedly to select Sound Specialfunto Tips To view the remaining sleep time, press the SLEEP button once. When you switch the Monitor off, the Monitor releases the preset sleep time. ΓThe Interface board (AP-42EA20) is not equipped on MZ-42PZ10 series model. Others ? ? 35 check list Troubleshooting ? No picture & ? No sound ? Check whether the Monitor is turned on. Check the power cord. Plug another product's power cord into the wall outlet where the Monitor's power cord was plugged in. Picture OK & ? No sound ? Press the VOLUME Check to see ? doesn't work No or or picture No output from of the one if the batteries to between the Monitor and are installed with the correct p.26) batteries. ? Adjust picture ? Keep ? Activate any function to restore the brightness of the picture. (If still picture is on the screen for more than 5 minutes, the a ? ? new items in the picture p.26) menu. (Refer to p.30) certain distance between the Monitor and the VCR. gets dark.) Check the kind of Adjust (Refer to Replace input signal. Balance in the sound menu. (Refer to p.32) Speakers ? Strange sound from the Monitor The ing reason strange sound the Monitor output on or faulty. comes from the Monitor when turn- off is due to the to the Monitor. This the Monitor is 36 causing object obstruction. ? screen Poor stereo sound see polarities. (Refer Poor colour Poor Check to button. if there is any the remote control The remote control (Γ) signals being input strange noise does or not mean that First ep Note Compsiton ConectiBasfu Picture Sound Specialfunto Others 37 Note 38 Product First ep specifications Compsiton MODEL Width MZ-42PZ10/B/G/K/S (inches) 25 Depth (inches) 3.2 Weight (pounds) 72.1 requirement 230V~ 50Hz Resolution Colour This product specifications quality improvement. ConectiBasfu 41.6 Height (inches) Power ? MT-42PZ10/B/G/K/S 110-240V~ 50/60Hz 852 x 480 Picture (Dot) 16,770,000 (256 steps of each R, G and B) above can be changed Sound without notice for Specialfunto Others 39 P/NO : 3828VA0293A b (MP00MC, 067G TX, 373-026H)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement