Philips | HTS3100/93 | Owner's Manual | Philips DVD home theatre system HTS3100/93 User manual

Philips DVD home theatre system HTS3100/93 User manual
DVD HOME THEATRE SYSTEM
English
HTS3100
HTS3105
User Manual
6
Փ⫼䇈ᯢк
50
CAUTION
LASER
Type
Wave length
Output Power
Beam divergence
Semiconductor laser
GaAIAs
650 - 660 nm (DVD)
784 - 796 nm (CD)
7 mW (DVD)
10 mW (VCD/CD)
60 degrees
Use of controls or adjustments or performance
of procedures other than herein may result in
hazardous radiation exposure or other unsafe
operation.
ATTENTION!
For Customer Use:
Read carefully the information located at the
bottom or rear of your DVD Home Theatre
System and enter below the Serial No. Retain
this information for future reference.
‘CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE
ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN
CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE ‘STANDARD
DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS
REGARDING OUR TV SET COMPATIBILITY WITH THIS
MODEL 525p AND 625p DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.’
2
Model No.
HTS3100, HTS3105
Serial No.
_______________
English
Manufactured under license from
Dolby Laboratories, “Dolby”, “Pro
Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
Manufactured under license from
Digital Theater Systems, Inc. U.S. Pat.
Noís. 5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,226,616; 6,487,535 and
other U.S. and world-wide patents
issued and pending. “DTS” and “DTS
Digital Surround” are registered
trademarks of Digital Theater
Systems, Inc. Copyright 1996, 2003
Digital Inc. All Rights Reserved.
DivX Ultra Certified products: “DivX,
DivX Ultra Certified, and associated
logos are trademarks of DivX, Inc. and
are used under license.
Windows Media and the Windows logo
are trademarks, or registered
trademarks of Microsoft Corporation
in the United States and/or other
countries.
3
Language Code
4
English ------------------------------------ 6
------------------------------ 50
5
English
Index
Table of contents
English
General
General Information ........................................................................................................ 8
Setup precautions.................................................................................................................................................8
Accessories supplied ...........................................................................................................................................8
Cleaning discs ........................................................................................................................................................8
About recycling .....................................................................................................................................................8
Product Overview
Main Unit ........................................................................................................................... 9
Remote Control .........................................................................................................10-12
Using the remote control ................................................................................................................................12
Connections
Basic Connections .....................................................................................................13-16
Step 1 : Placing the speakers ...........................................................................................................................13
Step 2 : Connecting the speakers and subwoofer.....................................................................................14
Step 3 : Connecting to TV ...............................................................................................................................15
Option 1: Using the Video (CVBS) socket .........................................................................................15
Option 2: Connecting to a Progressive Scan TV or component video input ............................15
Step 4 : Connecting the FM/MW antennas ...................................................................................................16
Step 5 : Connecting the power cord ............................................................................................................16
Optional Connections .................................................................................................... 17
Connecting audio from TV .............................................................................................................................17
Connecting audio from an analogue audio/video device.........................................................................17
Basic Setup
Getting Started .........................................................................................................18-23
Step 1: Turning on the DVD system .............................................................................................................18
Turning off to Eco Power standby mode ..............................................................................................18
Step 2: Finding the correct viewing channel ...............................................................................................18
Step 3: Setting language preferences ............................................................................................................19
On-screen display (OSD) language ........................................................................................................19
Audio, Subtitle and Menu language for DVD playback .............................................................. 19-20
Step 4: Setting the TV ...................................................................................................................................... 20
Selecting the matching colour system .......................................................................................... 20-21
Setting the TV Display ...............................................................................................................................21
Step 5: Setting up Progressive Scan feature............................................................................................... 22
Step 6: Setting the speakers’ channels ........................................................................................................ 23
Disc Playback
Disc Operations ........................................................................................................ 24-32
Playable discs .......................................................................................................................................................24
Playing a disc ........................................................................................................................................................24
Basic playback controls.................................................................................................................................... 25
Selecting various repeat/shuffle functions ................................................................................................. 25
Programming disc tracks ................................................................................................................................. 26
6
Other playback features for video discs (DVD/VCD/SVCD) ............................................................. 26
Using the Disc Menu ................................................................................................................................. 26
Viewing playback information ..................................................................................................................27
Resuming playback from the last stopped point ................................................................................27
Zooming in ....................................................................................................................................................27
Changing subtitle language (DVD only) ................................................................................................27
Changing sound track language .............................................................................................................. 28
Selecting camera angles ............................................................................................................................ 28
Playback Control (VCD only)................................................................................................................. 28
Preview function (VCD/SVCD only) .................................................................................................... 28
Playing an MP3/ JPEG/Window Media Audio disc ...................................................................................39
Playing a JPEG image file (slide show) ......................................................................................................... 30
Preview function ......................................................................................................................................... 30
Zoom picture ............................................................................................................................................. 30
Rotating/flipping the picture ................................................................................................................... 30
Playing MP3 music and JPEG pictures simultaneously .............................................................................31
Playing a DivX disc .............................................................................................................................................31
Playing a Karaoke disc .......................................................................................................................................32
Microphone setting ...................................................................................................................................32
Setup Options
DVD Setup Menu Options ....................................................................................... 33-39
Accessing the DVD setup menu.....................................................................................................................33
General Setup Page........................................................................................................................................... 34
Audio Setup Page............................................................................................................................................... 35
Video Setup Page ......................................................................................................................................... 36-37
Preference Setup Page ............................................................................................................................... 38-39
Radio Tuning
Tuner Operations ..................................................................................................... 40-41
Tuning to radio stations................................................................................................................................... 40
Presetting radio stations ................................................................................................................................. 40
Using auto install ........................................................................................................................................ 40
Using automatic preset..............................................................................................................................41
Using manual preset ...................................................................................................................................41
Selecting a preset radio station ......................................................................................................................41
Deleting a preset radio station.......................................................................................................................41
Changing tuning grid ..........................................................................................................................................41
Others
Sound and Volume Controls ......................................................................................... 42
Selecting surround sound................................................................................................................................ 42
Selecting digital sound effects ........................................................................................................................ 42
Volume control .................................................................................................................................................. 42
Other Features ............................................................................................................... 43
Controlling ‘Philips’ TV with the remote control .................................................................................... 43
Software upgrades ............................................................................................................................................ 43
Troubleshooting ........................................................................................................ 44-45
Glossary ..................................................................................................................... 46-47
Specifications ..................................................................................................................48
7
English
Table of contents
General Information
English
CAUTION!
The machine does not contain any
user-serviceable parts. Please leave
all maintenance work to qualified
personnel.
Setup precautions
Finding a suitable location
– Place the set on a flat, hard and stable
surface. Do not place the set on a carpet.
– Do not position the set on top of
other equipment that might heat it up
(e.g., receiver or amplifier).
– Do not put anything under the set
(e.g., CDs, magazines).
– Install this unit near the AC outlet
where the AC power plug can be easily
reached.
Space for ventilation
– Place the apparatus in a location with
adequate ventilation to prevent internal
heat build up. Allow at least 10 cm (4”)
clearance from the rear and the top of
the set and 5cm (2”) from the left and
right to prevent overheating.
5cm (2.3")
10cm (4.5")
Accessories supplied
–
–
–
–
–
–
–
–
1 passive subwoofer
4 satellite speakers
1 centre speaker
1 remote control with batteries
1 composite video cable (yellow)
1 FM wire antenna
1 MW loop antenna
Quick Start Guide
Cleaning discs
Some problems occur (frozen picture,
sound disruptions, picture distortions)
because the disc inside the unit is dirty.
To avoid these problems, discs should be
cleaned on a regular basis.
To clean a disc, use a micro fibre cleaning
cloth and wipe the disc from the centre
to the edge in a straight line.
CAUTION!
Do not use solvents such as benzene,
thinner, commercially available cleaners,
or anti-static sprays intended for discs.
10cm (4.5")
About recycling
5cm (2.3")
Avoid high temperatures, moisture,
water and dust
– Apparatus must not be exposed to
dripping or splashing.
– Do not place any sources of danger
on the apparatus (e.g., liquid filled
objects, lighted candles).
8
These operating instructions have been
printed on non-polluting paper. The
electronic equipment contains a large
number of materials that can be recycled.
If you are disposing of an old machine,
please take it to a recycling centre.
Please observe the local regulations
regarding disposal of packaging materials,
exhausted batteries and old equipment.
1
2
a STANDBY ON 2
– Turns on the system or turns off to Eco
Power standby mode.
b Disc tray
c OPEN CLOSE ç
– Opens/ closes the disc tray.
d System display panel
e u (PLAY PAUSE)
– DISC: starts/pauses playback.
– TUNER: starts auto tuner installation for
first time setup.
3
4
5
6
7
8
English
Main Unit
9
f SOURCE
– Selects the relevant active source mode:
DISC, TUNER (FM/MW), TV or AUX.
g VOL
– Adjusts the volume level.
h MIC LEVEL
– Activates microphone level mode and use
the VOLUME control to set the
microphone volume level.
i MIC
– For connecting the microphone socket.
Ç (STOP)
– Exits an operation.
– DISC: stops playback.
– TUNER: hold down this button to erase
the current preset radio station.
.>
– DISC: selects a track or hold down this
button to search backward/forward.
– TUNER: selects a preset radio station.
9
Remote Control
English
c ZOOM
– Enlarges a picture on the TV screen.
1
2
3
4
5
d AUDIO
– Selects an audio language (DVD) or an
audio channel (CD).
e SETUP
– Enters or exits the system setup menu.
f DISPLAY
– Displays the current status or disc
information.
6
g PLAY É
– DISC: starts playback.
7
8
9
10
11
12
h STOP Ç
– Exits an operation.
– DISC: stops playback.
– DISC: hold down this button to open and
close the disc tray.
– TUNER: hold down this button to erase
the current preset radio station.
i TV VOL +– Adjusts TV volume (Philips TV only).
j Numeric Keypad (0-9)
– Enters a track/title number of the disc.
– Enters a number of a preset radio station.
k REPEAT
– Selects various repeat modes; turns off
repeat mode.
l VOCAL
a2
– Turns off to Eco Power standby mode.
b Source buttons
– DISC: switches to DISC mode.
TUNER: toggles between FM and MW
band.
TV: switches to TV mode.
The sound from the TV will output
through the connected speakers system.
AUX/DI: switches to the external device
which is connected to this DVD system.
10
– Toggles between various audio mode
options.
KARAOKE
– Enters microphone setup menu.
Remote Control (continued)
English
m SUBTITLE
– Selects a DVD subtitle language.
n ANGLE
– Selects a DVD disc camera angle (if
available).
o DISC MENU
– For DVD, enter or exit disc contents
menu.
– For VCD/SVCD, enter digest menu.
pWXST
– DISC: selects movement direction in the
menu.
– TUNER: press left or right to tune the
radio frequency.
– TUNER: press up or down to start auto
search.
q OK
– Confirms a selection.
13
14
15
16
17
18
19
20
21
22
r RETURN/TITLE
– For DVD, go back to the previous menu.
– For VCD version 2.0 only;
In stop mode, turn on/off playback
control (PBC) mode.
During playback, display the disc title
menu or return to the main menu.
23
24
25
s.>
– DISC: hold down this button for fast
forward and backward search.
– TV: selects previous/next channel (Philips
TV only).
– TUNER: selects a preset radio station.
t PAUSE Å
– DISC: pauses playback.
u VOL +-
w PROGRAM
– DISC: starts programming.
– TUNER: hold down this button to start
automatic/ manual preset programming.
– Adjusts the volume level.
x SURR.
v MUTE
– Selects multi-channel surround or
stereo mode.
– Mutes or restores the volume.
y SOUND
– Selects a predefined sound effect.
11
Remote Control (continued)
English
Using the remote control
A Open the battery compartment.
B Insert two batteries type R03 or AAA,
following the indications (+-) inside
the compartment.
C Close the cover.
D Point the remote control directly at the
remote sensor (iR) on the front panel.
E Select the source you wish to control by
pressing the DISC, TUNER, TV or
AUX/DI button on the remote control.
F Then select the desired function (for
example ., >).
12
CAUTION!
– Remove batteries if they are
exhausted or if the remote control
is not to be used for a long time.
– Do not mix batteries (old and new
or carbon and alkaline, etc.).
– Batteries contain chemical
substances, so they should be
disposed of properly.
English
Basic Connections
Step 1: Placing the speakers
The Philips Home Theatre System is
simple to install. However, proper
system placement is critical to ensure an
optimum sound experience.
A Place the front left and right speakers at
equal distances from the TV and at an
angle of approximately 45 degrees from
the listening position.
B Place the centre speaker above the TV or
Helpful Hints:
– The placement diagram shown here is only
a guideline that will provide great system
performance. You may find other placement
choices that are more suitable for your room
layout and provide the sound experience you
enjoy.
– To avoid magnetic interference, do not
position the front speakers too close to your
TV.
– The rear speakers are labelled as REAR
LEFT or REAR RIGHT.
– The front speakers are labelled as
FRONT LEFT or FRONT RIGHT.
the DVD system so that the centre
channel’s sound is localised.
C Place the rear speakers at normal
listening ear level facing each other or
hang on the wall.
D Place the subwoofer at the corner of the
room. Keep at least one metre away
from the TV.
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
13
Basic Connections (continued)
English
SUBWOOFER
FRONT
LEFT
FRONT
RIGHT
CENTER
REAR LEFT
REAR RIGHT
Step 2: Connecting the
speakers and subwoofer
Connect all the speakers and subwoofer
to the speaker sockets at the rear of the
DVD system. Make sure that the colours
of the plugs and sockets are matched.
Helpful Hint:
– To prevent unwanted noise, do not place
the speakers too close to the DVD system,
AC power adapter, TV or any other radiation
sources.
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
14
English
Basic Connections (continued)
OR
Option 2
Option 1
Step 3: Connecting to TV
This connection enables you to view the
playback from this DVD system. You only
need to choose one of the options
below to make your video connection.
– For a standard TV, follow option 1.
– For a progressive scan TV, follow
option 2.
IMPORTANT!
Connect the DVD system directly
to the TV.
Option 1: Using the Video (CVBS)
socket (good picture quality)
Use the supplied composite video cable
(yellow) to connect the CVBS socket on
the DVD system to the video input
socket (or labelled as A/V In, Video In,
Composite or Baseband) on the TV.
Option 2: Connecting to a
Progressive Scan TV or component
video input
The progressive scan video quality is only
available when using Y Pb Pr connection
and a progressive scan TV is required. It
provides superior picture quality when
watching DVD movies.
A Follow option 1 to make the basic video
connection.
B Use the component video cables (red/
blue/green - not supplied) to connect the
Y PB PR sockets on the DVD system to
the corresponding component video
input sockets (or labelled as Y Pb/Cb Pr/
Cr or YUV) on the TV.
C If your TV accepts progressive signals,
proceed to ‘Getting Started - Step 5:
Setting up Progressive Scan feature’ for
detailed progressive feature setup.
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
15
Basic Connections (continued)
English
fix the claw
into the slot
>
TV
FM antenna
2
MW
antenna
1
Step 4: Connecting the FM/
MW antennas
A Connect the supplied MW loop antenna
to the MW socket. Place the MW loop
antenna on a shelf, or attach it to a stand
or wall.
B Connect the supplied FM antenna to the
FM socket. Extend the FM antenna and
fix its ends to the wall.
For better FM stereo reception, connect
an external FM antenna (not supplied).
Step 5: Connecting the
power cord
After everything is connected
properly, plug the AC power cord
into the power outlet.
The Eco Power LED on the DVD system
will light up. Never make or change any
connections with the power turned on.
Helpful Hints:
– Refer to the type plate at the rear or
bottom of the product for identification and
supply ratings.
Helpful Hints:
– Adjust the position of the antennas for
optimal reception.
– Position the antennas as far away as
possible from your TV, VCR or other
radiation source to prevent any unwanted
interference.
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
16
English
Optional Connections
Connecting audio from TV
When connecting the audio output from
your TV to this Home Theatre Audio
System, you can enjoy the multi-channel
surround sound capabilities.
Use an audio cable (red/white - not
supplied) to connect the TV IN jacks on
this DVD system to the AUDIO OUT
sockets on the TV.
To listen to the sound, press TV on the
remote control as the sound source that
you want to play.
Connecting audio from an
analogue audio/video device
You can connect the audio output from
an analogue audio/video device (e.g. VCR,
Cable/Satellite Box or TV) to this Home
Theatre Audio System in order to enjoy
the multi-channel surround sound
capabilities
Use an audio cable (red/white - not
supplied) to connect the AUX IN
sockets on this DVD system to the
AUDIO OUT jacks on the connected
device.
To listen to the sound, press AUX/DI as
the sound source that you want to play.
Helpful Hint:
– To see the picture of the connected video
device (e.g. VCR), connect the VIDEO OUT
socket of the device to the VIDEO IN socket
of the TV, and select the correct input
channel on the TV.
TIPS: Refer to the respective connected device’s user manual for other possible connections.
17
Getting Started
English
Step 1: Turning on the DVD
system
A Press STANDBY ON (2).
B Press the SOURCE button on the front
panel repeatedly to select :
DISC J FM J MW J TV J AUX
J DISC ....
Step 2: Finding the correct
viewing channel
Before you start ...
Make sure you have completed all the
necessary connections before proceeding.
A Press SOURCE button until “DISC”
appears on the display panel.
B Turn on the TV and set it to the correct
Or
Press DISC, TUNER, TV or AUX/DI
on the remote control.
Turning off to Eco Power standby
mode
Press STANDBY ON (2).
The display screen will turn off.
18
video-in channel. You should see the
blue DVD background screen on the TV.
You may go to Channel 1 on your TV,
then press the Channel Down button on
your TV’s remote control until you see
the Video In channel.
You may press ° button repeatedly
on your TV’s remote control.
Usually this channel is between the
lowest and highest channels and may be
called FRONT, A/V IN, VIDEO. See your
TV manual for more details.
Step 3: Setting language
preferences
The language options are different
depending on your country or region. It
may not correspond to the illustrations
shown on the user manual.
On-screen display (OSD) language
The OSD (On-Screen Display) language
for this DVD system will remain as you
have set it, regardless of the changes
made to the DVD disc language.
A In ‘DISC’ mode, press SETUP on the
remote control.
{ General Setup Page } appears.
B Use ST keys to highlight { OSD
Language }, then press X.
General Setup Page
Disc Lock
Display Dim
Program
OSD Language
Screen Saver
DivX(R) VOD Code
English
Dansk
Deutsch
Espanõl
Audio, Subtitle and Menu language
for DVD playback
You can select your preferred language
settings for DVD playback. If the
selected language is recorded on the
DVD disc, the DVD system will
automatically play the disc in that
language. Otherwise, the disc’s default
language will be used instead.
A Press Ç twice to stop playback (if any),
then press SETUP.
B Press X repeatedly to select
{ Preference Page }.
C Use ST keys to highlight one of the
options below, then press X.
Preference Page
Audio
Subtitle
Disc Menu
PBC
MP3/JPEG Nav
Password
DivX Subtitle
Default
{ Audio }
Selects the preferred audio language for
DVD playback.
C Use ST keys to select a language and
press OK to confirm.
{ Subtitle }
Selects the preferred subtitle language for
DVD playback.
{ Disc Menu }
Selects the preferred disc menu language
for DVD playback.
D Use ST keys to select a language and
press OK to confirm.
TIPS: Press W to go back to the previous menu item. Press SETUP to exit the menu.
19
English
Getting Started (continued)
Getting Started (continued)
English
If the language you want is not
available in the list, select { Others }.
Use the numeric keypad (0-9) on the
remote control to enter the 4-digit
language code ‘XXXX’ (see page 4) and
press OK to confirm.
E Repeat steps C ~ D for other settings.
Helpful Hints:
– During DVD playback, you can switch the
audio and subtitle languages by pressing the
AUDIO and SUBTITLE buttons on the
remote control. However, this does not
change the default settings you have made
here.
– For some DVDs, the subtitle/audio/menu
language can only be changed via the DVD
disc menu.
Step 4: Setting the TV
Selecting the matching colour
system
The colour system of the DVD system,
DVD and TV should match. Only then
will it be possible to play a DVD on this
system. Before changing the TV system,
determine the colour system of your TV.
A In ‘DISC’ mode, press SETUP on the
remote control.
B Press X repeatedly to select { Video
Setup Page }.
C Press T to highlight { TV Type }, then
press X.
Video Setup Page
TV Type
TV Display
Progressive
Picture Setting
NTSC
PAL
Multi
{ PAL }
Select this if the connected TV has the
PAL colour system. It will change the
video signal of an NTSC disc and output
it to PAL format.
{ NTSC }
Select this if the connected TV has the
NTSC colour system. It will change the
video signal of a PAL disc and output it to
NTSC format.
{ Multi }
Select this if the connected TV is
compatible with both NTSC and PAL
(multi-system). The output format will
be in accordance with the video signal of
the disc.
TIPS: The underlined option is the factory default setting.
Press W to go back to the previous menu item. Press SETUP to exit the menu.
20
D Select one of the options and press OK
to confirm.
Follow the instructions shown on the
TV to confirm the selection (if any).
If a blank/distorted TV screen appears,
wait for 15 seconds for the auto recovery.
Setting the TV Display
Set the aspect ratio of the DVD system
according to the TV type you have
connected. The format you select must
be available on the disc. If it is not, the
setting for TV display will not affect the
picture during playback.
A In ‘DISC’ mode, press SETUP on the
remote control.
B Press X repeatedly to select { Video
Setup Page }.
C Press T to highlight { TV Display },
then press X.
Video Setup Page
TV Type
TV Display
Progressive
Picture Setting
4:3 Pan Scan
4:3 Letter Box
16:9 Wide Screen
{ 4:3 Pan Scan }
Select this if you have a
conventional TV and
want both sides of the
picture to be trimmed or formatted
to fit your TV screen.
{ 4:3 Letter Box }
Select this if you have a
conventional TV. In this
case, a wide picture with
black bands on the upper and lower
portions of the TV screen will be
displayed.
{ 16:9 Wide Screen }
Select this if you have a
wide-screen TV.
D Select one of the options and press OK
to confirm.
TIPS: The underlined option is the factory default setting.
Press W to go back to the previous menu item. Press SETUP to exit the menu.
21
English
Getting Started (continued)
Getting Started (continued)
English
Step 5: Setting up
Progressive Scan feature
(for Progressive Scan TV only)
The progressive scan displays twice the
number of frames per second than
interlaced scanning (ordinary normal TV
system). With nearly double the number
of lines, progressive scan offers higher
picture resolution and quality.
Before you start...
Ensure that you have connected this
DVD system to a progressive scan TV
using the Y Pb Pr connection (see
‘Option 2: Connecting to a Progressive
Scan TV or component video input’).
A Turn off your TV progressive scan mode
or turn on to the interlaced mode (refer
to your TV’s user manual).
B Turn on the DVD system and press
SOURCE button until “DISC” appears
on the display panel.
C Turn on the TV and set it to the correct
video-in channel.
The blue DVD background screen will
appear on the TV.
D Press SETUP on the remote control.
E Press X repeatedly to select { Video
Setup Page }.
F Select { Progressive } > { On, } then
press OK to confirm.
Video Setup Page
TV Type
TV Display
Progressive
Picture Setting
G Read the notification message on the TV
and confirm your action by selecting the
in the menu and press OK.
If a blank/distorted screen appears, wait
for 15 seconds for the auto recovery.
Otherwise, select { Cancel } and press
OK to go back to the previous menu.
There will be no picture on your TV
at this state until you have turned
on the progressive scan mode on
your TV.
H Turn on your TV progressive scan mode
(refer to your TV’s user manual).
A message appears on the TV.
I Confirm your action by selecting the
in the menu and press OK.
The setup is now completed and you
can start to enjoy the high quality picture.
If no picture is displayed:
A Press OPEN CLOSE to open the disc
tray.
B Press W on the remote control.
C Press MUTE on the remote control.
Helpful Hint:
– There are some progressive scan TVs and
High-Definition TVs that are not fully
compatible with this unit, resulting in an
unnatural picture when playing back a DVD
VIDEO disc in the progressive scan mode. In
this case, turn off the progressive scan
feature on both the DVD system and your
TV.
On
Off
TIPS: The underlined option is the factory default setting.
Press W to go back to the previous menu item. Press SETUP to exit the menu.
22
Getting Started (continued)
You can adjust the delay times (centre
and surround only) and volume level for
individual speakers. These adjustments let
you optimise the sound according to
your surroundings and setup.
Before you start...
Stop the disc playback by pressing STOP
button twice or remove the disc from
the disc tray. Otherwise, the settings are
not accessible.
A In ‘DISC’ mode, press SETUP on the
remote control.
E Use ST keys to highlight { Speakers
Delay }, then press X.
English
Step 6: Setting the speakers’
channels
Audio Setup Page
Speakers Volume
Speakers Delay
Night Mode
CD Upsampling
Speakers Distance Setup
Center
Rear Left
Rear Right
0ms
0ms
0ms
F Use W X keys to set the delay times
(0 ms ~ 15 ms) for centre and rear
speakers that best suit your surround
sound needs.
G Press OK to confirm.
B Press X repeatedly to select { Audio
Setup Page }.
C Press T to highlight { Speakers
Volume }, then press X.
Audio Setup Page
Speakers Volume
Speakers Delay
Night Mode
CD Upsampling
Speakers Level Setup
Front Left
Front Right
0dB
0dB
Center
Subwoofer
Rear Left
Rear Right
0dB
0dB
Helpful Hints:
– A 1ms increase/decrease of delay time is
equivalent to 30 cm change in distance.
– Use the longer delay time settings when
the rear speakers are closer to the listener
than the front speakers.
– The test tone will be automatically
generated to help you judge the sound level
of each speaker.
0dB
0dB
D Use W X keys to set the volume level for
each speaker (-6dB ~ +6dB) and press
OK to confirm.
TIPS: Press W to go back to the previous menu item. Press SETUP to exit the menu.
23
Disc Operations
English
Playable discs
IMPORTANT!
– If the inhibit icon (ø or X) appears
on the TV screen when a button is
pressed, it means the function is not
available on the current disc or at
the current time.
– Do not put any objects other than
discs on the disc tray. Doing so may
cause the disc player to malfunction.
Playing a disc
Your DVD home theatre system will
play:
– Digital Versatile Discs (DVDs)
– Video CDs (VCDs)
– Super Video CDs (SVCDs)
– Finalised DVD+Recordable (DVD±R),
DVD+Rewritable (DVD±RW)
– Audio Compact Discs (CDs)
– MP3/ Windows Media™ Audio discs,
picture (Kodak, JPEG) files on
CD-R(W)
– ISO 9660/UDF format
– JPEG resolution support up to
3072 x 2048
– Supported sampling frequencies :
32 kHz, 44.1 kHz, 48 kHz
– Supported Bit-rates : 32~256 (kbps),
variable bit rates (average 128 kbps)
– DivX files on CD-R(W)/DVD+R(W):
– DivX 3/4/5/6, DivX Ultra
– Supports QPEL (Quarter Pixel).
Region Codes for DVD discs
DVD discs and players are designed with
regional restrictions. Before playing a disc,
make sure the disc is for the same region
as your player. The regional code for this
DVD system is indicated at the rear panel.
A Press SOURCE repeatedly until “DISC”
appears on the display panel (or press
DISC on the remote control).
B Turn on the TV to the Video In channel
for the DVD system (e.g. ‘EXT’, ‘0’, ‘AV’).
You should see the blue DVD
background screen on the TV.
C Press OPEN CLOSE ç to open the
disc tray and load a disc, then press the
same button again to close the disc tray.
Make sure the disc label is facing up.
For double-sided discs, load the side
which you want to play facing up.
You can also hold down the STOP
button on the remote control to open
and close the disc tray.
D Playback will start automatically.
See the following pages for more
playback options and features.
Helpful Hint:
– If you are having trouble playing a certain
disc, remove the disc and try a different one.
Improperly formatted discs will not play on
this DVD system.
TIPS: Some discs cannot be played on this player due to the configuration and characteristics of the
disc, or due to the condition of recording and authoring software that was used.
24
Basic playback controls
Pausing playback
During playback, press u (or Å on
the remote control).
While in pause mode, you can press
Å repeatedly to view the next still
picture (for video playback only).
To resume playback, press u (or
PLAY X on the remote control).
Selecting another track/chapter
Press ./ > or use the numeric
keypad (0-9) to key in a track/chapter
number.
If the repeat track mode is active, press
. again to replay the same track/
chapter.
Searching backward/forward
Hold down ./ >.
While searching, press ./ >
repeatedly to decrease/increase the
search speed.
To resume normal playback, press
u (or PLAY X on the remote
control).
Stopping playback
Press Ç.
English
Disc Operations (continued)
Selecting various repeat/
shuffle functions
While playing a disc, press REPEAT on
the remote control repeatedly to choose
a repeat play mode.
DVD
RPT ONE (repeat chapter)
RPT TT (repeat title)
SHUFFLE (random play)
RPT SHF (repeat random play)
RPT OFF (exit repeat mode)
VCD/SVCD/CD
RPT ONE (repeat track)
RPT ALL (repeat disc)
SHUFFLE (random play)
RPT SHF (repeat random play)
RPT OFF (exit repeat mode)
MP3/DivX/Windows Media™ Audio
RPT ONE (repeat track)
RPT ALL/FLD (repeat folder)
SHUFFLE (random play)
RPT OFF (exit repeat mode)
Helpful Hint:
– Repeat playback is not possible on VCDs
when the PBC mode is turned on.
Helpful Hint:
– This is a power-saving feature, the system
will automatically switch to Eco Power
standby mode if you do not press any
buttons within 30 minutes after a disc has
stopped playing.
TIPS: The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.
25
Disc Operations (continued)
English
Programming disc tracks
(not for Picture CD/MP3)
You can play the contents of the disc in
the order you want by programming the
playing order of the tracks.
Other playback features
for video discs (DVD/VCD/
SVCD)
A Press PROGRAM on the remote
control.
The programming menu appears.
6
7
2
8
9
10
Exit
Start
Next
B Use the numeric keypad (0-9) to
enter a valid track/chapter number.
C Use WXST keys to move the cursor to
the next position.
If there are more than ten total
programme tracks, select { Next } on
the screen and press OK (or press >
on the remote control) to access the
next programming page.
To remove the track/chapter from the
programming menu, select the track/
chapter and press OK.
D Once complete, select { Start } on the
screen and press OK to start playback.
Playback will start from the selected
track under the programmed sequence.
Using the Disc Menu
Depending on the disc format, a menu
may appear on the TV screen once you
load the disc.
To select a playback feature or item
Use WXST keys or numeric keypad
(0-9) on the remote control, then press
OK to start playback.
To access or remove the menu
Press DISC MENU on the remote
control.
E To exit the programme menu, select
{ Exit } in the menu and press OK.
TIPS: The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.
26
Viewing playback information
This DVD system can display the disc
playback information (for example, title
or chapter number, elapsed playing time,
audio/subtitle language) and a number of
operations can be done without
interrupting disc playback.
A During playback, press DISPLAY.
A list of available disc information
appears on the TV.
DVD
Resuming playback from the last
stopped point
This DVD system is able to resume disc
playback from its last stopped point (only
possible for the last 10 discs that were
recorded without a menu).
A Load one of the last 10 discs played.
B While “LOADING” appears on the
display panel, press PLAY X (or u) to
start playback from the last stop point.
To cancel the resume mode
Press Ç twice.
Zooming in
VCD/SVCD
This option allows you to enlarge the
picture on the TV screen and to pan
through the enlarged picture.
A During playback, press ZOOM on the
remote control repeatedly to select a
different zoom factor.
Use WXST keys to move through
the zoomed image.
Playback will continue.
B Use ST keys to view the information
and press OK to access.
B Press ZOOM repeatedly to return to
the original size.
C Use the numeric keypad (0-9) to input
the number/time or use ST keys to
make the selection, then press OK to
confirm.
Playback will change according to the
chosen time or to the selected title/
chapter/track.
Changing subtitle language (DVD
only)
This operation works only on DVDs with
multiple subtitle languages. You can
change the language you want while
playing a DVD.
Press SUBTITLE repeatedly to select
different subtitle languages.
TIPS: The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.
27
English
Disc Operations (continued)
Disc Operations (continued)
English
Changing sound track language
This operation works only on DVDs with
multiple soundtrack languages, you can
change the language you want while
playing a DVD.
Press AUDIO repeatedly to select the
available audio languages.
For VCD – changing the audio
channel
Press AUDIO repeatedly to select the
available audio channels provided by the
disc (STEREO, MONO LEFT, MONO
RIGHT or MIX MONO).
Switching camera angles
Preview function (VCD/SVCD only)
This function allows you to preview the
contents of a VCD/SVCD.
A Press DISC MENU.
Select Digest Type:
Track Digest
Disc Interval
Track Interval
B Use ST keys to select one of the
following options and press OK.
{ Track Digest }
View six different tracks on one screen each
time. It allows you to have a quick glance at all
the tracks on the disc.
This option is only available with DVDs
that contain sequences recorded from
different camera angles. This allows you
to view the picture from different angles.
{ Disc Interval }
Press ANGLE repeatedly to select the
available camera angles.
{ Track Interval }
Playback Control (VCD only)
Playback Control (PBC) playback allows
you to play Video CDs interactively,
following the menu on the display. This
function can also be accessed via the
‘Preference Page’ menu.
For VCDs with Playback Control
(PBC) feature (version 2.0 only)
When playback is stopped, press
RETURN/TITLE to turn on or off the
PBC mode.
During playback, press RETURN/
TITLE to return to the disc title menu
or main menu.
View the whole disc in six thumbnail pictures.
It divides a disc into six portions at regular
intervals and displays them on one screen.
View the content of a single track in six
thumbnail pictures. It divides a single track
into six portions at regular intervals and
displays them on one screen.
This option is only available during playback
mode.
01
02
03
04
05
06
Exit
Menu
To go to the previous or next page, press
./ >.
To return to the main menu, select
{ Menu } on the screen and press OK.
Press OK on the selected thumbnail
picture to start playback from there.
C To exit the preview menu, select
{ Exit } on the screen and press OK.
TIPS: The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.
28
Disc Operations (continued)
This DVD system can playback most of
the MP3, JPEG and Windows Media™
Audio files recorded on a CD-R/RW disc
or commercial CD.
Before you start ...
Turn on your TV to the correct Video In
channel. See the section on ‘Finding the
correct viewing channel’.
During playback, you can;
English
Playing an MP3/ JPEG/
Windows Media™ Audio disc
Press ./ > to playback another
track/file in the current folder.
Hold down ./ > to fast reverse/
forward search for a music track.
To select another folder from the
current disc, press S to return to the
root menu. Use ST keys to make your
selection and press OK to confirm.
Press REPEAT repeatedly to access
various play modes.
D To stop playback, press Ç.
A Insert a disc.
The disc reading time may exceed 30
seconds due to the complexity of the
directory/file configuration.
The disc menu appears on the TV.
00:19 04:39
001/003
\MP3_files_128kbs
Helpful Hint:
– To skip the folders menu when you load a
MP3/JPEG disc, set the MP3/JPEG NAV
setting in the Preference Setup Page to
{ Without Menu }.
Previous
Picture 1
Picture 2
MP3 Music 1
MP3 Music 2
050
003
000
B If the disc main menu contains various
folders, use ST keys to select a desired
folder and press OK to open the folder.
C Use ST keys to select a track/file and
press OK to start playback.
Playback will start from the selected
file and continue through to the end of
the folder.
TIPS: Some discs cannot be played on this player due to the configuration and characteristics of the
disc, or due to the condition of recording and authoring software that was used.
29
Disc Operations (continued)
English
Playing a JPEG image file
(slide show)
Before you start ...
Turn on your TV to the correct Video In
channel. See the section on ‘Finding the
correct viewing channel’.
Insert a Picture disc (Kodak Picture CD,
JPEG).
For a Kodak disc, the slide show will
begin automatically.
For a JPEG disc, the picture menu will
appear on the TV. Press PLAY X (or
u) to start the slide-show playback.
Preview function
A During playback, press Ç.
12 thumbnail pictures will be displayed
on the TV.
B Press ./ > to display the other
pictures on the previous/next page.
C Use WXST keys to highlight one of the
pictures and press OK to start playback.
Zoom picture
A During playback, press ZOOM
repeatedly to select a different zoom
factor.
B Use WXST keys to pan through the
zoomed image.
Helpful Hint:
– This feature is not applicable for DivX
disc.
Rotating/flipping the picture
During playback, use WXST keys to
rotate/flip the picture on the TV.
S : flip the picture vertically
T : flip the picture horizontally
W : rotate the picture anti-clockwise
X : rotate the picture clockwise
Supported file format:
– The file extension has to be ‘*.JPG’
and not ‘*.JPEG’.
– It can only display DCF-standard still
pictures or JPEG pictures e.g. TIFF. It
cannot play back moving pictures, Motion
JPEG, Progressive JPEG and other
formats, or pictures in formats other
than JPEG, or pictures associated with
sound.
– It may require longer time for the
DVD system to display the disc content
on the TV due to the large number of
songs/pictures compiled into one disc.
D Press DISC MENU to return to Picture
CD menu.
TIPS: Some discs cannot be played on this player due to the configuration and characteristics of the
disc, or due to the condition of recording and authoring software that was used.
30
Playing MP3 music and JPEG
pictures simultaneously
You can create a musical slide show if the
disc contains both the MP3 music and
JPEG picture files.
A Insert an MP3 disc that contains music
and pictures.
B Select an MP3 track in the menu and
press PLAY X (or u) to start
playback.
C During MP3 music playback, use WXST
keys to select a picture folder from the
disc menu and press PLAY X (or u).
The picture files will be played back
through to the end of the folder.
D To stop simultaneous playback, press
DISC MENU and followed by Ç.
Helpful Hints:
– It is normal to experience an occasional
“skip” while listening to your MP3 disc.
– It is normal to experience an occasional
pixelation during MP3/DivX playback due to
poor clarity of digital contents during internet
downloading.
– Only the first session of a multi-session CD
will be played back.
Playing a DivX disc
This DVD system supports the playback
of DivX movies which you can copy from
your computer onto a CD-R/RW,
DVD+R/+RW disc (see ‘General Setup
Page - { DivX(R) VOD code }).
A Insert a DivX disc.
B If the DivX movie contains external
subtitles, the subtitle menu will appear on
the TV for your selection.
In this case, pressing SUBTITLE on the
remote control will turn the subtitle
display on or off.
C Press PLAY X (or u) to start
playback.
During playback, you can;
If multilingual subtitles are embedded on
the DivX disc, you can press SUBTITLE
to change the subtitle language while
playing.
Use W / X keys on the remote control
to perform fast reverse/forward search.
Press DISPLAY repeatedly until the
Time Search menu appears, key in the
time where playback should start and
press OK to confirm.
Playback skips to the time entered.
Helpful Hints:
– Subtitle files with the following file name
extensions (.srt, .smi, .sub, .ssa, .ass) are
supported but do not appear on the file
navigation menu.
– The subtitle file name has to be the same
as the file name of the movie.
– The subtitle can only be displayed up to an
average of 45 characters.
TIPS: Some discs cannot be played on this player due to the configuration and characteristics of the
disc, or due to the condition of recording and authoring software that was used.
31
English
Disc Operations (continued)
Disc Operations (continued)
English
Playing a Karaoke disc
Microphone setting
A Press KARAOKE on the remote
Before you start ...
Turn on your TV to the correct Video In
channel. See the section on ‘Finding the
correct viewing channel’.
A Connect a microphone (not supplied) to
control to access ‘Microphone Setup’
page.
Mic
On
Off
the MIC socket on the side panel of the
DVD main unit (as shown below).
B In ‘Microphone Setup’ page, use ST
keys to select the option for microphone
settings and press OK to confirm.
{ Mic }
– Use ST keys to turn on or off the
karaoke microphone.
{ Mic Volume }
– Use ST keys to set the microphone
volume level (00 ~ +20). Select ‘00’ for
minimum microphone volume setting.
B Insert a karaoke disc.
If the disc menu appears, use ST
keys to make your selection and press
OK to start playback.
{ Echo Level }
– Use ST keys to set the Echo Level
(00 ~ +20). Select ‘00’ for minimum
echo level setting.
C To turn off the vocal or change the sound
channel of a karaoke disc, press VOCAL
on the remote control repeatedly to
toggle between various audio modes.
D Start enjoying the karaoke.
While singing, you can set the
microphone volume level by pressing the
MIC LEVEL on the front panel followed
by adjusting the Volume control.
{ Key }
– Use ST keys to set the pitch level
(-10~ +10) that matching your voice.
Select ‘-10’ for lowest possible tone and
‘+10’ for highest tone. To return to
original tone, select ‘00’.
TIPS: Some discs cannot be played on this player due to the configuration and characteristics of the
disc, or due to the condition of recording and authoring software that was used.
32
Accessing the DVD setup
menu
This DVD system setup is carried out via
the TV, enabling you to customise the
DVD system to suit your particular
requirements.
OK
SETUP
General Setup Page
Disc Lock
Display Dim
Program
OSD Language
Screen Saver
DivX(R) VOD Code
see page 34
Audio Setup Page
Speakers Volume
Speakers Delay
Night Mode
CD Upsampling
see page 35
A In ‘DISC’ mode, press SETUP on the
remote control.
The setup menu appears.
B Use W X keys to select one of the setup
menu pages and press OK.
Video Setup Page
TV Type
TV Display
Progressive
Picture Setting
see page
36~37
If you are not able to access the
{ Preference Page }, press SETUP to
exit the menu. Then, press STOP (Ç)
twice before you press the SETUP
again.
C Use S T keys to select a setup option
and press X to access
D Select the setting you wish to change and
press OK to confirm and go back to the
previously selected item.
Instructions and explanations of the
options are provided in the following
pages.
If the option in the menu is greyed
out, that means the setting is not
available or cannot be changed in the
current state.
Preference Page
Audio
Subtitle
Disc Menu
PBC
MP3/JPEG Nav
Password
DivX Subtitle
Default
see pages
38~39
E To exit, press SETUP.
33
English
DVD Setup Menu Options
DVD Setup Menu Options (continued)
English
General Setup Page (underlined options are the factory default settings)
Disc Lock
Not all discs are rated or coded by the disc maker. You can
prevent a specific disc from playing by locking the disc. Up to 40
discs can be locked.
{ Lock }
– Selects this to block the playback of the
current disc. Subsequent access to a locked
disc requires a six-digit password. The
default password is ‘136900’ (see ‘Preference
Setup Page - { Password }).
{ Unlock }
– All discs can be played.
Display Dim
Selects the brightness of the DVD system display panel.
{ 100% }
– Full brightness.
{ 70% }
– Medium brightness.
{ 40% }
– Dimmest display.
Program
Access the track programming menu. See ‘Programming disc
tracks’ chapter.
OSD language
Selects the preferred language for the DVD system on-screen
display menu.
Screen Saver
The screen saver prevents damage to the TV screen by avoiding
exposure to a static image for too long.
{ On }
– Switches to TV screen saver mode when
playback has been stopped or paused for
more than 15 minutes.
{ Off }
– Turns off the screen saver function.
DivX(R) VOD code
Philips provides you with the DivX® VOD (Video On Demand)
registration code that allows you to rent and purchase videos
using the DivX® VOD service. Press X to see the registration
code and press OK to exit.
Use the registration code to purchase or rent the videos from
DivX® VOD service at www.divx.com/vod. Follow the
instructions and copy the video from your computer onto a
CD-R/RW disc for playback on this DVD system.
Note: All the downloaded videos from DivX® VOD can only be played
back on this DVD system. For more information, visit us at www.divx.
com/vod.
34
English
DVD Setup Menu Options (continued)
Audio Setup Page (underlined options are the factory default settings)
Speakers Volume
Access the speaker’s level setup menu. Use W X keys to adjust
the volume level for each connected speaker between -6dB to
+6dB.
Speakers Delay
Access the speaker’s distance setup menu. Use W X keys to set
the delay times for the centre and rear speakers based on the
listening position and distance.
Note: 1 ms increase/decrease of delay time is equivalent to 30 cm
change in distance. Use the longer delay time settings when the rear
speakers are closer to the listener than the front speakers.
Night Mode
This mode optimises playback of sound at low volume. High
volume outputs will be softened and low volume outputs will be
enhanced to an audible level. This feature is only applicable for
DVD video discs with Dolby Digital mode.
{ On }
– Turns on night mode.
{ Off }
– Turns off night mode feature. Selects this
to enjoy the surround sound with its full
dynamic range.
CD Upsampling
This feature enables you to convert your music CD to a higher
sampling rate using sophisticated digital signal processing for
better sound quality. If you have activated the CD upsampling
feature, the system will automatically switch to stereo mode.
{ Off }
– Turns off CD-upsampling.
{ 88.2 kHz (X2) } – Select this to convert the sampling rate of
the CDs twice as high as the original rate.
Note: If you press the SURR button on the remote control to select
multi-channel mode, it will turn off the CD upsampling feature.
35
DVD Setup Menu Options (continued)
English
Video Setup Page (underlined options are the factory default settings)
TV Type
Selects the colour system that matches the connected TV. It will
enable playback of a different type of disc (PAL or NTSC disc) on
this DVD system.
{ PAL }
– For PAL-system TV.
{ NTSC }
– For NTSC-system TV.
{ Multi }
– For TV that is compatible with both PAL and
NTSC.
TV Display
The picture shape can be adjusted to fit your TV.
{ 4:3 Letter Box }
– For a ‘wide-screen’ display
with black bars on the top
and bottom.
{ 4:3 Pan Scan }
– For a full-height picture
with the sides trimmed.
{ 16:9 Wide Screen } – For wide-screen TV
(frame ratio 16:9).
Progressive
Before enabling the progressive scan feature, you must ensure that
your TV can accept progressive signals (a progressive scan TV is
required) and that you have connected this DVD system to your
TV using the Y Pb Pr (see ‘Option 2: Connecting to a Progressive
Scan TV or component video input’).
{ On }
– Turns on progressive scan mode.
Read the instructions on the TV and confirm
your action by pressing OK on the remote
control.
{ Off }
– Disables the progressive scan mode.
Note: If no picture appears, wait for 15 seconds for auto recovery.
Otherwise, turn off the progressive scan as below:
1) Press OPEN CLOSE to open the disc tray.
2) Press W on the remote control.
3) Press MUTE on the remote control.
36
English
DVD Setup Menu Options (continued)
Video Setup Page (underlined options are the factory default settings)
Picture Setting
Personal Picture Setup
Brightness
Contrast
Tint
Color
This DVD system provides three predefined sets of picture
colour settings and one personal setting which you can define
yourself.
{ Standard }
– Original colour setting.
{ Bright }
– Vibrant colour setting.
{ Soft }
– Warm colour setting.
{ Personal }
– Selects this to personalise your picture
colour setting. Use W X keys to adjust to
the setting that best suits your personal
preference and press OK to confirm. For
an average setting, select { 0. }
{ Brightness }
Increase this value to brighten the picture colour
or vice versa.
{ Contrast }
Increase this value to sharpen the picture colour
or vice versa.
{ Tint }
Increase or decrease this value to change the
colour phase of the picture.
{ Color }
Increase this value to enhance the picture colour
or vice versa.
37
DVD Setup Menu Options (continued)
English
Preference Setup Page (underlined options are the factory default settings)
Audio
Selects the preferred audio language for DVD playback.
Subtitle
Selects the preferred subtitle language for DVD playback.
Disc Menu
Selects the preferred disc menu language for DVD playback.
Note: If the selected audio/subtitle/disc menu language is not available
on the DVD, the disc’s default language will be used instead.
PBC
Play Back Control feature is applicable for VCD/SVCD only. It
allows you to play Video CDs (2.0) interactively, following the
menu on the display.
{ On }
– The index menu (if available) will appear on
the TV when you load a VCD/SVCD.
{ Off }
– The VCD/SVCD will skip the index menu and
playback directly from the beginning.
MP3/JPEG Nav
MP3/JPEG Navigator can only be set if the disc is recorded with a
menu. It allows you to select different display menus for easy
navigation.
{ Without Menu} – Displays all the files contained in the MP3/
Picture disc.
{ With Menu }
– Displays the folder menu of the MP3/
Picture disc.
Note: This DVD system can only display 650 files/folder in the directory.
Password
The password is used for the Disc Lock. Enter your six-digit
password to play a locked disc or when prompted for a
password. The default password is ‘136900’. To change the
password:
1) Press OK to access the change password menu.
2) Use the numeric keypad 0-9 on the remote control to
enter your existing six-digit password at { Old Password }.
Change Password
Old Password
New Password
Confirm PWD
OK
Note: When doing this for the first time or if you forget your existing
password, key in ‘136900’.
3) Enter the new six-digit password at { New Password }.
4) Enter the new six-digit password again at { Confirm PWD }.
5) Press OK to confirm and exit the menu.
38
English
DVD Setup Menu Options (continued)
Preference Setup Page (underlined options are the factory default settings)
DivX Subtitle
Selects the font type that supports the recorded DivX subtitle.
{ Standard }
– Displays a standard list of Roman subtitle
fonts provided by this DVD system.
{ Others }
– Displays other subtitle fonts.
Default
This feature enables you to reset all the setup menu options and
your personal settings to the factory defaults, except your
password for the Disc Lock. Press OK to confirm the default
reset.
39
Tuner Operations
English
IMPORTANT!
Make sure the FM and MW
antennas are connected.
Tuning to radio stations
A Press SOURCE repeatedly until “FM”
Using auto install
This feature is only applicable for first
time radio station programming. You will
be prompted to install the radio stations
when you access the tuner mode. With
one touch of button, all the available
radio stations will be stored
automatically.
appears on the display panel (or press
TUNER on the remote control).
display panel
B Press S / T briefly on the remote
control to start tuning.
“SEARCH > or <” will appear on the
display panel until a radio station with
sufficient signal strength is found.
C Repeat step B if necessary until you find
the desired radio station.
D To fine-tune the reception of a weak
station, press W / X briefly and
repeatedly until optimal reception is
found.
Presetting radio stations
You can store up to 40 FM and 20 MW
preset radio stations in the memory.
There are three different ways to
programme the radio stations:
– Using auto install (for first time setup
only)
– Using automatic preset
– Using manual preset
Helpful Hints:
– The system will exit presetting mode if no
button is pressed within 20 seconds.
– If no stereo signal is detected or less than
5 (five) stations are detected during tuner
installation, “PLEASE CHECK ANTENNA”
appears.
40
A Press TUNER.
“AUTO INSTALL PRESS PLAY”
appears.
B Press PLAY X until “START ...” appears
on the display panel.
The system will start searching from
the FM band followed by the MW band.
All the available radio stations with
strong signal will be stored automatically.
Once complete, the last tuned radio
station will be played back.
Using automatic preset
Use automatic presetting to store or
reinstall all the preset radio stations.
A Press TUNER to select “FM” or “MW”
band.
B Hold down PROGRAM until
“START ...” appears on the display panel.
All previously stored radio stations
will be replaced.
Using manual preset
Deleting a preset radio station
A In tuner mode, use ./ > keys to
select a preset radio station.
B Hold down Ç until “FM/MW X
DELETED” appears.
“X” is the preset number.
The radio station continues to play
but has been deleted from the preset list.
The rest of the preset radio stations
remain unchanged.
Use manual presetting to store your
favourite radio stations.
A Tune to your desired radio station (see
“Tuning to radio stations”).
B Press PROGRAM.
C Use ./ > keys to select a preset
number that you want to store the
current radio station.
D Press PROGRAM to store.
Selecting a preset radio station
A Press TUNER to select “FM” or “MW”
band.
B Use ./ > keys to select a preset
number (or use the numeric keypad on
the remote control).
The waveband, preset number
followed by the radio frequency will
appear on the display panel.
Changing tuning grid
(not available for all versions)
In some countries, the frequency step
between adjacent channels in the MW/FM
band is 9 kHz/ 50 kHz (10 kHz/ 100 kHz
in some areas).
IMPORTANT!
Changing the tuning grid will erase
all previously stored preset radio
stations.
A Press SOURCE to select “FM” or
“MW”.
B Press STANDBY ON to switch the
DVD system to standby mode.
C Press STANDBY ON and PLAY X
together on the front panel to power up
the DVD system.
The display will show “GRID 9” or
“GRID 10”.
Helpful Hint:
– GRID 9 and GRID 10 indicate that the
tuning grid is in step of 9 kHz and 10 kHz
respectively.
41
English
Tuner Operations (continued)
Sound and Volume Controls
English
Selecting digital sound effects
Select a preset digital sound effect that
matches your disc’s content or that
optimises the sound of the musical style
you are playing.
Press SOUND to select the available
sound effect.
MUTE
SURR.
SOUND
When playing movie discs or in TV mode,
you can select :
CONCERT, DRAMA, ACTION or
SCI-FI.
When playing music discs or while in
TUNER or AUX/DI mode, you can select :
CLASSIC, JAZZ, ROCK or DIGITAL.
Selecting surround sound
Press SURR. to select : DOLBY+PL II
(multi-channel) or STEREO.
The availability of the various
surround sound modes depends on the
sound available on the disc.
The centre and rear speakers operate
only in multi-channel surround mode.
The available output modes for Multichannel include: Dolby Digital, DTS
(Digital Theatre Systems) Surround and
Dolby Pro Logic II.
Stereo broadcasts or recordings will
produce some surround channel effects
when played in a surround mode.
However, mono (single channel sound)
sources will not produce any sound from
the rear speakers.
Helpful Hint:
– You are not able to select the surround
sound mode if the system setup menu is
turned on.
42
Helpful Hint:
– For flat sound output, select CONCERT or
CLASSIC.
Volume control
Press VOL +/- on the remote
control to increase or decrease the
volume level.
“VOL MIN” is the minimum volume
level and “VOL MAX” is the maximum
volume level.
To turn off the volume temporarily
Press MUTE on the remote control.
Playback will continue without sound
and “MUTE” appears.
To restore the volume, press MUTE
again, or increase the volume level.
Controlling ‘Philips’ TV with
the remote control
This DVD system’s remote control
enables you to control the basic functions
of your ‘Philips’ brand TV.
English
Other Features
Software upgrades
Periodically Philips will issue software
upgrades to enhance your user
experience.
Before you start ...
Check the current software version of
this DVD system:
1) Press OPEN CLOSE ç to open the
disc tray.
2) Press DISPLAY on the remote
control.
A Visit the Philips website ‘www.philips.
com/support’ to check the availability of
the latest software upgrade. Download
the software to a CD-R.
B Press OPEN CLOSE ç to open the
disc tray.
C Insert the CD-R and press
A Press SOURCE repeatedly until “TV”
appears on the display panel (or press
TV on the remote control).
B Use ./ > keys or the numeric
keypad (0-9) to select the TV’s channel.
OPEN CLOSE ç again.
The software will start to install on
the recorder automatically.
IMPORTANT!
Power supply must not be interrupted
during upgrade!
C Press TV VOL +/- to adjust the TV’s
volume level.
43
display panel
Troubleshooting
English
WARNING
Under no circumstances should you try to repair the system yourself, as this will
invalidate the warranty. Do not open the system as there is a risk of electric shock.
If a fault occurs, first check the points listed below before taking the system for repair. If
you are unable to solve a problem by following these instructions, consult your dealer or
Philips for help.
Problem (General)
Solution
No power.
– Check if the AC power cord is properly connected.
– Press the 2(STANDBY ON) on the front of the
DVD system to turn on the power.
No picture.
– Refer to your TV’s manual for correct Video In
channel selection. Change the TV channel until you
see the DVD screen.
– Press the DISC button to select disc mode.
– If this happens when you are turning on the progressive
scan feature, wait for 15 seconds for the auto recovery.
Completely distorted picture
or black/white picture.
– If this happens when you are changing the setting of the
‘TV TYPE’, wait for 15 seconds for the auto recovery.
– Check the video connection.
– Sometimes a small amount of picture distortion may
appear. This is not a malfunction.
– Clean the disc.
No sound or distorted sound.
– Adjust the volume.
– Check the speaker connections and settings.
– Make sure that the audio cables are connected and
press the SOURCE button to select the correct input
source (for example, TV or AUX/DI) to choose the
device that you want to hear through the DVD system.
There is no sound from the
centre and rear speakers.
– Make sure that the centre and rear speakers are
connected correctly.
– Press the SURR. button to select a correct surround
sound setting.
– Make sure that the source you are playing is recorded or
broadcast in surround sound (DTS, Dolby Digital, etc.).
The remote control does not
function properly.
– Select the source you want to play (for example,
DISC or TUNER) before pressing the function button
(X, ./ >).
– Reduce the distance between the remote control and
the system.
– Replace the batteries with new ones.
– Point the remote control directly toward the IR sensor.
– Check that the batteries are loaded correctly.
44
Troubleshooting (continued)
Solution
English
Problem (Playback)
The DVD system does not
start playback.
– Insert a readable disc with the playback side facing
down. The DVD+R/CD-R must be finalised.
– Check the disc type, colour system (PAL or NTSC)
and region code.
– Check for any scratches or smudges on the disc.
– Press SETUP to turn off the system setup menu
screen.
– You may need to enter the password in order to
unlock the disc for playback.
– Moisture may have condensed inside the system.
Remove the disc and leave the system turned on for
about an hour.
The aspect ratio of the screen
cannot be changed even
though you have set the TV
display.
– The aspect ratio is fixed on the DVD disc.
– Depending on the TV, it may not be possible to
change the aspect ratio.
Cannot activate some
features such as Angles,
Subtitles, or multi-language
Audio.
– The features may not be available on the DVD.
– Changing the language for the sound or subtitle is
prohibited on this DVD.
Not able to select some
items in the setup/system
menu.
– Press STOP button twice before selecting the system
setup menu.
– Depending on the disc availability, some menu items
cannot be selected.
Unable to play DivX movies.
– Check that the DivX file is encoded in ‘Home
Theatre’ mode with DivX certified encoder.
Radio reception is poor.
– If the signal is too weak, adjust the antenna or
connect an external antenna for better reception.
– Increase the distance between the system and your
TV or VCR.
– Tune in to the correct frequency.
– Place the antenna further away from any equipment
that may be causing the interference.
The DVD system does not
work.
– Disconnect the power cord from the power outlet
for a few minutes. Reconnect the power cord and try
to operate again as usual.
45
Glossary
English
Analogue: Sound that has not been turned
into numbers. Analogue sound varies, while
digital sound has specific numerical values.
These sockets send audio through two
channels, the left and right.
Aspect ratio: The ratio of vertical and
horizontal sizes of a displayed image. The
horizontal vs. vertical ratio of conventional
TVs is 4:3, and that of wide-screens is 16:9.
Bit Rate: The amount of data used to hold
a given length of music; measured in kilobits
per second, or kbps. Or, the speed at which
you record. Generally, the higher the bit
rate, or the higher the recording speed, the
better the sound quality. However, higher bit
rates use more space on a disc.
Chapter: Sections of a picture or a music
piece on a DVD that are smaller than titles.
A title is composed of several chapters. Each
chapter is assigned a chapter number
enabling you to locate the chapter you want.
Disc menu: A screen display prepared for
allowing a selection of images, sounds,
subtitles, multi-angles, etc to be recorded on
a DVD.
DivX: The DivX code is a patent-pending,
MPEG-4 based video compression
technology, developed by DivXNetworks,
Inc., that can shrink digital video to sizes
small enough to be transported over the
internet, while maintaining high visual quality.
Dolby Digital: A surround sound system
developed by Dolby Laboratories containing
up to six channels of digital audio (front left
and right, surround left and right, centre and
subwoofer).
46
Dolby Surround Pro Logic II: It is an
improved matrix decoding technology that
provides better spatiality and directionality
on Dolby Surround programme material,
provides a convincing three dimensional
sound field on conventional stereo music
recordings and is ideally suited to bring the
surround experience to automotive sound.
While conventional surround programming
is fully compatible with Dolby Surround Pro
Logic II decoders, soundtracks will be able to
be encoded specifically to take full advantage
of Pro Logic II playback, including separate
left and right surround channels. (Such
material is also compatible with conventional
Pro Logic decoders).
DTS: Digital Theatre Systems. This is a
surround sound system, but it is different
from the Dolby Digital. The formats were
developed by different companies.
JPEG: A very common digital still picture
format. A still picture data compression
system proposed by the Joint Photographic
Expert Group, which features a small
decrease in image quality in spite of its high
compression ratio.
MP3: A file format with a sound data
compression system. “MP3” is the
abbreviation of Motion Picture Experts
Group 1 (or MPEG-1) Audio Layer3. By
using the MP3 format, one CD-R or CD-RW
can contain about 10 times more data than a
regular CD.
Multichannel: DVDs are formatted to have
each sound track constitute one sound field.
Multichannel refers to a structure of sound
tracks having three or more channels.
Glossary (continued)
English
Playback control (PBC): Refers to the
signal recorded on video CDs or SVCDs for
controlling playback. By using menu screens
recorded on a Video CD or SVCD that
supports PBC, you can enjoy interactive
playback and searching.
Progressive Scan: The progressive scan
displays twice the number of frames per
second than in an ordinary TV system. It
offers higher picture resolution and quality.
Region code: A system allowing discs to be
played only in the region designated. This
unit will only play discs that have compatible
region codes. You can find the region code
of your unit by looking at the product label.
Some discs are compatible with more than
one region (or ALL regions).
Surround: A system for creating realistic
three dimensional sound fields full of realism
by arranging multiple speakers around the
listener.
Title: The longest section of a movie or
music feature on DVD. Each title is assigned
a title number, enabling you to locate the
title you want.
VIDEO OUT socket: Yellow socket on
the back of the DVD system that sends the
DVD picture video to a TV.
47
Specifications
English
AMPLIFIER
Output power:
- HTS3100
- Front :
- Rear:
- Centre :
- Subwoofer:
MAIN UNIT
200 W / 2400 PMPO
25 W / channel
25 W / channel
50 W
50 W
- HTS3105
500 W / 6000 PMPO
- Front :
75 W / channel
- Rear:
75 W / channel
- Centre :
100 W
- Subwoofer:
100 W
Frequency Response: 20 Hz – 20 kHz / –3 dB
Signal-to-Noise Ratio: > 65 dB (CCIR)
Input Sensitivity
- AUX In :
1000 mV
TUNER
Tuning Range:
FM 87.5–108 MHz (50kHz)
MW 531–1602 kHz (9kHz)
MW 530–1700 kHz (10kHz)
26 dB Quieting
Sensitivity:
FM 20 dB, MW 4μV/m
Image Rejection Radio:FM 25 dB, MW 28 dB
IF Rejection Ratio:
FM 60 dB, MW 45 dB
Signal-to-Noise Ratio: FM 60 dB, MW 40 dB
AM Suppression Ratio: FM 30 dB
Harmonic Distortion: FM Mono 3%
FM Stereo 3%
MW 5%
Frequency Response: FM 180 Hz–10 kHz / ±6 dB
Stereo Separation:
FM 26 dB (1 kHz)
Stereo Threshold:
FM 23.5 dB
DISC SECTION
Laser Type:
Disc Diametre:
Video Decoding:
Semiconductor
12cm / 8cm
MPEG-1 / MPEG-2 /
/ DivX 3/4/5/6, Ultra
12 Bits
PAL / NTSC
4:3 / 16:9
60~65 dB
Video DAC:
Signal System:
Video Format :
Video S/N:
Composite Video
Output
1.0 Vp-p, 75Ω
Audio DAC:
24 Bits / 192 kHz
Frequency Response: 4 Hz–20 kHz (44.1 kHz)
4 Hz–22 kHz (48 kHz)
4 Hz–44 kHz (96 kHz)
Power Supply Rating: 110–127 V / 220–240 V;
50/60 Hz switchable
Power Consumption
- HTS3100
70 W
- HTS3105
150 W
Eco Standby power: < 1 W
Dimensions:
360 x 54 x 324 (mm)
(w x h x d)
Weight:
- HTS3100
2.64 kg
- HTS3105
2.9 kg
SPEAKERS
FRONT and REAR speakers
System:
- HTS3100
1-way, closed box system
- HTS3105
2-way, closed box system
Impedance
- HTS3100
4Ω
- HTS3105
8Ω
Speaker drivers:
1 x 76mm (3”)woofer
Frequency response: 120 Hz – 20 kHz
Dimensions:
97.5 x 191.3 x 71.4 (mm)
(w x h x d)
Weight:
0.56 kg/each
CENTRE speaker
- HTS3100
- HTS3105
Impedance
- HTS3100
- HTS3105
Speaker drivers:
Frequency response:
Dimensions:
Weight:
SUBWOOFER
Impedance
- HTS3100
- HTS3105
Speaker drivers:
Frequency response:
Dimensions:
Weight:
1-way, closed box system
2-way, closed box system
8Ω
4Ω
1 x 76mm (3”) woofer
120 Hz – 20 kHz
239 x 99.6 x 69.4 (mm)
(w x h x d)
0.72 kg
8Ω
4Ω
152mm (6”) woofer
30 Hz – 120 Hz
194 x 266 x 339.5 (mm)
(w x h x d)
3.5 kg
Specifications subject to change without prior
notice.
48
49
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising