Barco FL40-4K User manual
Add to my manuals
10 Pages
Barco FL40-4K: Unleash Stunning Visual Experiences with Immersive 4K Resolution and Advanced Collaboration Tools
Harness the power of 4K resolution and experience captivating visuals with the Barco FL40-4K projector. Designed for modern meeting rooms, auditoriums, and large venues, this projector delivers sharp, lifelike images with exceptional color accuracy and contrast. Engage your audience with immersive presentations, videos, and multimedia content like never before.
Equipped with advanced collaboration features, the FL40-4K seamlessly integrates with your existing conferencing systems. Share content wirelessly from multiple devices, including laptops, smartphones, and tablets, using the projector's built-in wireless connectivity options. Annotate and interact with projected content in real-time, fostering dynamic and engaging collaboration among participants.
advertisement
FL40 Series Safety Manual ENABLING BRIGHT OUTCOMES Barco Fredrikstad AS Habornveien 53, N-1630 Gamle Fredrikstad, Norway [email protected] www.barco.com Registered office: Barco NV President Kennedypark 35, 8500 Kortrijk, Belgium www.barco.com/en/support www.barco.com Safety and environmental information 1 Safety and environmental information About Read this chapter thoroughly before attempting to install or operate the projector. To prevent personal injury to users or physical damage to the projector while installing and using your projector, ensure that you understand and follow all safety guidelines, instructions and warnings included in this chapter and this manual. Clarification of the term FL40 series used in this document Use in this document of the term, FL40 , means that the content is applicable for the following products: • • • • FL40 - WU FL40 - 4K FS40 - WU FS40 - 4K Defining the FL40 platform The FL40 series products in general, are all products within the Barco GP5 platform 1.1 General considerations Notice on optical radiation FL40 Series • • • • Do not stare into Beam. This projector is Risk Group 2 (RG2) according to IEC EN 62471-5. Any operation or adjustment not specifically instructed by the user’s guide creates the risk of hazardous light radiation exposure. Do not open or disassemble the projector as this may cause danger to unauthorized personnel General safety instructions • • • • • • • This product contains no user serviceable parts. Attempts to modify/replace mechanics or electronics inside the housing or compartments will violate any warranties and may be hazardous. Do not stare into beam when the projector is on. The bright light may result in permanent eye damage. Before operating this equipment please read this manual thoroughly and retain it for future reference. Installation and preliminary adjustments should be performed by properly trained and qualified personnel. All warnings on the projector and in the documentation manuals must be adhered to. All instructions for operating and use of this equipment must be followed precisely. All local installation codes should be adhered to. Notice on safety This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, as basis for National safety regulation world wide. The safety standard covers information technology equipment including electrical business equipment intended to operate in “normal” environments (offices and homes). This safety standard imposes important requirements on the use of safety critical components, materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of fire. Simulated single fault condition testing reduce the risk of hazards and contribute to ensure the safety of the equipment to the user even when the equipment’s normal operation fails. Users definition Throughout this manual, the term SERVICE PERSONNEL refers to Barco authorized persons having appropriate technical training and experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize the potential risk to themselves or other persons. Only Barco authorized SERVICE PERSONNEL, knowledgeable of such risks, are allowed to perform service functions inside the product enclosure. The term USER and OPERATOR refers to any person other than SERVICE PERSONNEL. 1.2 Important safety instructions To prevent the risk of electrical shock • • • • • • This product should be operated from a mono phase AC power source. This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power cables are the correct one, consult your dealer. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug. Never use 2- wire power cords, as this is dangerous and could lead to electrical shock. Always use a power connector with a ground terminal. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself. Ensure that the main power cord complies with the national regulations at the site where the equipment is used. Do not use unauthorized replacements Do not operate the projector with a damaged cord. Replace the cord. R5910126 /01 FL40 Series 3 Safety and environmental information • • • • • • • • • • • • Do not operate the projector if the projector has been dropped or damaged - until it has been examined and approved for operation by a qualified service technician. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces. If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated for less amperage than the projector may overheat. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock. Make sure that no objects enter into the vents and openings of the set. Do not expose this projector to rain or moisture. The projector is designed for indoor use only. Never operate the unit outdoors. Do not immerse or expose this projector in water or other liquids. Do not spill liquid of any kind on this projector. Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before resuming operations. Do not disassemble this projector, always take it to an authorized trained service person when service or repair work is required. Do not use an accessory attachment which is not recommended by the manufacturer. Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges. To prevent personal injury • • • • • • • • To prevent injury and physical damage, always read this manual and all labels on the system before connecting to the wall outlet or adjusting the projector. To prevent injury, take note of the weight of the projector. To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures. Warning: high intensity light beam. NEVER look into the lens! High luminance could result in damage to the eye. Always switch off the projector and disconnect from the mains power supply before attempting to remove any of the projector covers or access parts inside the projector. This product contains no user serviceable parts. Attempts to modify/replace mechanics or electronics inside the housing or compartments will violate any warranties and may be hazardous. Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and possible injury to the user. Only place the projector on a stable surface, or mount it securely using an approved ceiling-mount. To prevent fire hazard • • • • • • • • • • • • • • Barco projection products are designed and manufactured to meet the most stringent safety regulations. This projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe. Exposing flammable or combustible materials into close proximity of this projector could result in the spontaneous ignition of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of the projector whereby no flammable or combustible materials are present. Do not place flammable or combustible materials near the projector! Caution! Hot air is exhausted from the rear vent. Do not place objects that are sensitive to heat nearer than 25 cm (10”) to the exhaust vent. Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the projector too close to walls, or other similar surface. Allow for sufficient distance to walls and ceilings to avoid overheating. Minimum safety distance to the exhaust area of the unit must not be less than 25 cm (10”) and to the intake area, not less than 25 cm (10”). This projector should never be placed near or over a radiator or heat register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided. Do not cover the projector or the lens with any material while the projector is in operation. Keep flammable and combustible materials away from the projector at all times. Mount the projector in a well-ventilated area away from sources of ignition and out of direct sun light. Always allow ample airflow through the projector. Never expose the projector to rain or moisture. In the event of fire, use sand, CO2 or dry powder fire extinguishers. Never use water on an electrical fire. Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this projector. Projection rooms must be well ventilated or cooled in order to avoid heat buildup. Let the projector cool down completely before storing. Remove cord from the projector when storing. To prevent projector damage • • • • • • 4 To ensure correct airflow is maintained, the projector should only be operated when all of its covers in place. The exception from this is the front cover, that can be removed to give access to multiple anchor points. See User Guide for more detailed info regarding this issue. Always remove lens cap before switching on the projector. If the lens cap is not removed, it may melt due to the high energy light emitted through the lens. Melting the lens cap may permanently damage the surface of the projection lens Only connect the projector to signal sources and voltages as described in the technical specification. Connecting to unspecified signal sources or voltages may lead to malfunction and permanent damage of the unit. To ensure correct airflow is maintained, it should only be operated when all of its covers are in place. The projector must always be installed in a manner which ensures free flow of air into its air inlets and unimpeded evacuation of the hot air from its cooling system. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, R5910126 /01 FL40 Series Safety and environmental information • • • • • • • sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The device should not be placed in a built-in installation or enclosure unless proper ventilation is provided. Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the mains supply immediately. Do not operate the projector again until it has been checked by Barco authorized service personnel. Do not block the projector cooling fans or free air movement around the projector. Minimum safety distance to the exhaust area of the unit must not be less than 25 cm (10”) and to the intake area, not less than 25 cm (10”). Do not use this equipment near water. Do not operate the projector outside its temperature and humidity specifications as this may result in overheating and malfunction. Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror Devices™ in which case there is a loss of warranty. Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution. To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner. On servicing • • • • Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials and risk of electric shock. Refer all servicing to Barco authorized repair centers. Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can lead to permanent damage to the projector and cancellation of the warranty. Unplug this product from the wall outlet and refer servicing to Barco authorized service personnel or technicians under the following conditions: - If liquid has been spilled into the equipment. - If the product has been exposed to rain or water. - If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. - If the product has been dropped or the cabinet has been damaged. - If the product exhibits a distinct change in performance, indicating a need for service. - When the power cord or plug is damaged or frayed. • • Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replacement parts. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty. Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 1.3 Safety Symbols FL40 / FS40 Description of safety symbols used in product documentation or on product. Image Description Refer to user manual for further information! Caution! Do not stare into beam, RG2 product. No telephone! Do not connect to telephone lines. R5910126 /01 FL40 Series 5 Safety and environmental information Image Description FL40 EMC Label EMC: This is a class A product. In a domestic environment this product may cause radio Interference in which case the user may be required to take adequate measures. 警告使用者 此為甲類資訊技術設備,於居住環境中使用時,可能會造成射頻擾動, RG2 IEC EN 62471-5 在此種情況下,使用者會被要求採取某些適當的對策。 FCC: This device complies with part 15 of the FCC Rules, Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CANADA: This Class A digital apparatus complies with Canadian ICES-003, / Cet appareil numerique de Ia classe est conforme à Ia norme NMB-003 du Canada. FL40 RG2 Label RG2 IEC EN 62471-5 1.4 Location of labels Label positions EMC: This is a class A product. In a domestic environment this product may cause radio Interference in which case the user may be required to take adequate measures. 警告使用者 此為甲類資訊技術設備,於居住環境中使用時,可能會造成射頻擾動, RG2 IEC EN 62471-5 RG2 IEC EN 62471-5 在此種情況下,使用者會被要求採取某些適當的對策。 FCC: This device complies with part 15 of the FCC Rules, Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CANADA: This Class A digital apparatus complies with Canadian ICES-003, / Cet appareil numerique de Ia classe est conforme à Ia norme NMB-003 du Canada. Image 1-1: Location of RG2 and EMC label. 1.5 Disposal Information Disposal Information Waste Electrical and Electronic Equipment This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. For more information about recycling of this product, please contact your local city office or your municipal waste disposal service. For details, please visit the Barco website at: http://www.barco.com/AboutBarco/weee WEEE Information This product conforms to all requirements of the EU Directive on waste electrical and electronic equipment (WEEE). This product shall be recycled properly. It can be disassembled to facilitate proper recycling of it’s individual parts. Consult your dealer or relevant public authority regarding drop-off points for collection of WEEE. For details, please visit the Barco website at: http://www.barco.com/en/ AboutBarco/weee. 6 R5910126 /01 FL40 Series Safety and environmental information 1.6 Turkey RoHS compliance Turkey RoHS compliance Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur. [Republic of Turkey: In conformity with the WEEE Regulation] 1.7 China RoHS compliance 中国大陆 RoHS (Information for China ROHS compliance) 根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS), 以下部分列出了Barco产品中可能包含的有毒和/ 或有害物质的名称和含量。中国大陆RoHS指令包含在中国信息产业部MCV标准:“电子信息产品中有毒物质的限量要求”中。 According to the “Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of toxic substances in Electronic Information Products”. 零件项目(名称) Component name 有毒有害物质或元素 Hazardous substances and elements 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr6+) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 印制电路配件 Printed Circuit Assemblies X O X O O O 外接电(线)缆 External Cables X O O O O O 內部线路 Internal wiring X O O O O O 镜头支架 Lensholder X O O O O O 螺帽,螺钉(栓),螺旋( 钉),垫圈, 紧固件 Nuts, bolts, screws, washers, Fasteners X O O O O O 电源供应器 Power Supply Unit X O O O O O 风扇 Fan X O O O O O 附電池遙控器 Remote control X O O O O O 本表格依据SJ/T 11364的规定编制 This table is prepared in accordance with the provisions of SJ/T 11364. O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 GB/T 26572 标准规定的限量要求以下. O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in GB/T 26572. X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 标准规定的限量要求. X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in GB/T 26572. 10 在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标 准贴上环保使用期限(EFUP)标签。Barco产品所采用的EFUP标签(请参阅实例,徽标内部的编号使用于指定产 品)基于中国大陆的《电子信息产品环保使用期限通则》标准。 All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with the “Marking for the restriction of the use of hazardous substances in electrical and electronic product” of Chinese Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the photo) is based on the “General guidelines of environment-friendly use period of electronic information products” of Chinese Mainland. R5910126 /01 FL40 Series 7 Safety and environmental information 1.8 Taiwan RoHS compliance 限用物質含有情況標示聲明書 (Declaration of the Presence Condition of the Restricted Substances Marking) 限用物質及其化學符號 Restricted substances and its chemical symbols 單元 Unit 鉛 Lead (Pb) 汞 Mercury (Hg) 鎘 Cadmium (Cd) 六價鉻 Hexavalent chromium (Cr6+) 多溴聯苯 Polybrominated biphenyls (PBB) 多溴二苯醚 Polybrominated diphenyl ethers (PBDE) 印製電路板配件 Printed Circuit Assemblies — O — O O O 外接電(線)纜 External Cables — O O O O O 內部線路 Internal wiring — O O O O O 鏡頭支架 Lensholder — O O O O O 螺絲組件 Nuts, bolts, screws, washers, Fasteners — O O O O O 電源供應器 Power Supply Unit — O O O O O 風扇 Fan — O O O O O 遙控器 Remote control — O O O O O 備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準值。 Note 1:“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. 備考2.〝〇〞係指該項限用物質之百分比含量未超出百分比含量基準值。 Note 2:“〇” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. 備考3.〝—〞係指該項限用物質為排除項目。 Note 3:The “—” indicates that the restricted substance corresponds to the exemption. 備註: 此RoHS表格適用於以下產品型號: GP5 Hint: This RoHS table is suitable for following models: GP5 1.9 Contact information Barco contact information Registered office address: President Kennedypark 35, 8500 Kortrijk, Belgium Contact address: Beneluxpark 21, 8500 Kortrijk, Belgium Contact address (for Taiwan) : 公司名稱 (Company Name):巴可股份有限公司 地址 (Address):新北市板橋區新站路16號33樓 傳真 (Fax):02-7715 0298 電話 (Tel):02-7715 0299 E-mail:[email protected] Importers contact information To find your local importer, contact Barco directly or one of Barco's regional offices via the contact information given on Barco's web site, www.barco.com. Contact information Norway factory Barco Fredrikstad as Habornveien 53, N1630 Gamle Fredrikstad, Norway 8 R5910126 /01 FL40 Series Safety and environmental information Phone: +476930 4550 Support:[email protected] 1.10 Production Address Factories Barco NV (BELGIUM) President Kennedypark 35 , B-8500 Kortrijk Barco Fredrikstad AS (NORWAY) Habornveien 53, N-1630 Gamle Fredrikstad 1.11 Product Info Product info Image 1-2 product name 產品名稱: projector 投影機 model 型號: GP5 1.12 Statement EN55032/CISPR32 Class A MME (MultiMedia Equipment) Warning : This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference. Class A ITE (Information Technology Equipment) Warning : This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 警告使用者: 此為甲類資訊技術設備,於居住環境中使用時,可能會造成射頻擾動,在此種情況下,使用者會被要求採取某些適當的對 策。 R5910126 /01 FL40 Series 9 R5910126 /01 | 2019-05-24 Barco Fredrikstad AS | Habornveien 53, N-1630 Gamle Fredrikstad, Norway Registered office: Barco NV | President Kennedypark 35, 8500 Kortrijk, Belgium www.barco.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project