- Industrial & lab equipment
- Electrical equipment & supplies
- Batteries & accessories
- Battery chargers
- Schumacher
- Duralast DL-75D Automatic Battery Charger
- Owner's manual
Schumacher Duralast DL-75D Automatic Battery Charger Owner Manual
Add to my manuals
16 Pages
Schumacher Duralast DL-75D Automatic Battery Charger is an advanced and reliable charging solution for your 12-volt lead-acid batteries. It's perfect for charging cars, motorcycles, ATVs, lawnmowers, boats, and other vehicles. With its microprocessor-controlled charging algorithm, the DL-75D ensures a safe and efficient charge every time, extending the life of your battery and maximizing its performance. Its compact design and intuitive interface make it easy to use, even for beginners.
advertisement
▼
Scroll to page 2
of 16
Automatic Battery Charger OWNERS MANUAL PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE. This manual will explain how to use the charger safely and effectively. Please read and follow these instructions and precautions carefully. 102-9 1. IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS 1.1 1.2 1.3 1.4 SAVE THESE INSTRUCTIONS – This manual contains important safety and operating instructions. Keep out of reach of children. Do not expose the charger to rain or snow. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock or injury to persons. To reduce the risk of damage to electric plug and cord, pull by the plug rather than the cord when disconnecting charger. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If an extension cord must be used, make sure: • The pins on plug of extension cord are the same number, size and shape as those of plug on charger. • The extension cord is properly wired and in good electrical condition • The wire size is large enough for AC ampere rating of charger as specified in section 8. Do not operate charger with damaged cord or plug – replace the cord or plug immediately. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceperson. Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. WARNING: RISK OF EXPLOSIVE GASES. a. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS EACH TIME YOU USE THE CHARGER. b. To reduce risk of battery explosion, follow these instructions and those published by battery manufacturer and manufacturer of any equipment you intend to use in vicinity of battery. Review cautionary markings on these products and on engine. 1.5 1.6 1.7 1.8 1.9 1.10 1.11 2. PERSONAL SAFETY PRECAUTIONS 2.1 2.2 2.3 2.4 Consider having someone close enough by to come to your aid when you work near a lead-acid battery. Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes. Wear complete eye protection and clothing protection. Avoid touching eyes while working near battery. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately flood eye with running cold water for at least 10 minutes and get medical attention immediately. NEVER smoke or allow a spark or flame in vicinity of battery or engine. Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or short-circuit battery or other electrical part that may cause explosion. Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a leadacid battery. A lead-acid battery can produce a short-circuit current high enough to weld a ring or the like to metal, causing a severe burn. Use charger for charging 12V LEAD-ACID (STD, AGM OR GEL) rechargeable batteries. It is not intended to supply power to a low voltage electrical system other than in a starter-motor application. Do not use battery charger for charging dry-cell batteries that are commonly used with home appliances. These batteries may burst and cause injury to persons and damage to property. NEVER charge a frozen battery. 2.5 2.6 2.7 2.8 2.9 0099002152-00 3. PREPARING TO CHARGE 3.1 If necessary to remove battery from vehicle to charge, always remove grounded terminal from battery first. Make sure all accessories in the vehicle are off, so as not to cause an arc. 3.2 Be sure area around battery is well ventilated while battery is being charged. 3.3 Clean battery terminals. Be careful to keep corrosion from coming in contact with eyes. 3.4 Add distilled water in each cell until battery acid reaches level specified by battery manufacturer. Do not overfill. For a battery without removable cell caps, such as valve regulated lead acid batteries, carefully follow manufacturer’s recharging instructions. 3.5 Study all battery manufacturer’s specific precautions while charging and recommended rates of charge. 3.6 Determine voltage of battery by referring to car owner’s manual and make sure that output voltage selector switch is set at correct voltage. If charger has adjustable charge rate, charge battery initially at lowest rate. 4. CHARGER LOCATION 4.1 4.2 4.3 4.4 4.5 Locate charger as far away from battery as DC cables permit. Never place charger directly above battery being charged; gases from battery will corrode and damage charger. Never allow battery acid to drip on charger when reading electrolyte specific gravity or filling battery. Do not operate charger in a closed-in area or restrict ventilation in any way. Do not set a battery on top of charger. 5. DC CONNECTION PRECAUTIONS 5.1 Connect and disconnect DC output clips only after setting any charger switches to “off” position and removing AC cord from electric outlet. Never allow clips to touch each other. 5.2 Attach clips to battery and chassis, as indicated in sections 6 and 7. 6. FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE 6.8 WARNING: A SPARK NEAR THE BATTERY MAY CAUSE A BATTERY EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY: Position AC and DC cords to reduce risk of damage by hood, door, or moving engine part. Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons. Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has larger diameter than NEGATIVE (NEG, N, –) post. Determine which post of battery is grounded (connected) to the chassis. If negative post is grounded to chassis (as in most vehicles), see (6.5). If positive post is grounded to the chassis, see (6.6). For negative-grounded vehicle, connect POSITIVE (RED) clip from battery charger to POSITIVE (POS, P, +) ungrounded post of battery. Connect NEGATIVE (BLACK) clip to vehicle chassis or engine block away from battery. Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block. For positive-grounded vehicle, connect NEGATIVE (BLACK) clip from battery charger to NEGATIVE (NEG, N, –) ungrounded post of battery. Connect POSITIVE (RED) clip to vehicle chassis or engine block away from battery. Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block. When disconnecting charger, turn switches to off, disconnect AC cord, remove clip from vehicle chassis, and then remove clip from battery terminal. See Operating Instructions for length of charge information. 7. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE 6.1 6.2 6.3 6.4 6.5 6.6 6.7 WARNING: A SPARK NEAR THE BATTERY MAY CAUSE A BATTERY EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY: 7.1 Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has a larger diameter than NEGATIVE (NEG, N, –) post. 7.2 Attach at least a 24-inch-long 6-gauge (AWG) insulated battery cable to NEGATIVE (NEG, N, –) battery post. 7.3 Connect POSITIVE (RED) charger clip to POSITIVE (POS, P, +) post of battery. •2• 7.4 Position yourself and free end of cable as far away from battery as possible – then connect NEGATIVE (BLACK) charger clip to free end of cable. 7.5 Do not face battery when making final connection. 7.6 When disconnecting charger, always do so in reverse sequence of connecting procedure and break first connection while as far away from battery as practical. 7.7 A marine (boat) battery must be removed and charged on shore. To charge it on board requires equipment specially designed for marine use. 8. GROUNDING AND AC POWER CORD CONNECTIONS This battery charger is for use on a nominal 120 volt circuit and has a grounded plug. The charger must be grounded, to reduce the risk of electric shock. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. The plug pins must fit the receptacle (outlet). Do not use with an ungrounded system. 8.2 DANGER: Never alter the AC cord or plug provided – if it does not fit the outlet, have a proper grounded outlet installed by a qualified electrician. An improper connection can result in a risk of an electric shock or electrocution. NOTE: Pursuant to Canadian Regulations, use of an adapter plug is not allowed in Canada. Use of an adapter plug in the United States is not recommended and should not be used. 8.3 USING AN EXTENSION CORD The use of an extension cord is not recommended. If you must use an extension cord, follow these guidelines: • Pins on plug of extension cord must be the same number, size, and shape as those of plug on charger. • Ensure that the extension cord is properly wired and in good electrical condition. • Wire size must be large enough for the AC ampere rating of charger, as specified: 8.1 Length of cord (feet) AWG* size of cord 25 18 *AWG-American Wire Gauge 9. 50 16 100 12 150 10 ASSEMBLY INSTRUCTIONS 9.1 Remove all cord wraps and uncoil the cables prior to using the battery charger. 10. CONTROL PANEL LED INDICATORS CHARGING (yellow/orange) LED lit: The charger is charging the battery. CHARGED/MAINTAINING (green) LED lit: The battery is fully charged and the charger is in maintain mode. CLAMPS REVERSED/BAD BATTERY (red) LED flashing: The connections are reversed. CLAMPS REVERSED/BAD BATTERY (red) LED lit: The charger has detected a problem with the battery. See Troubleshooting for more information. NOTE: See Operating Instructions for a complete description of the charger modes. RATE SELECTION Use this button to select one of the following: 6<>2A CHARGE/MAINTAIN – For charging small and large batteries. The charger will automatically adjust the charging current, based on battery size, in order to charge the battery completely, efficiently and safely. Not recommended for industrial applications. BOOST – For quickly adding energy to a severely discharged or large capacity battery prior to Engine Start. ENGINE START – Provides additional amps for cranking an engine with a weak or run-down battery. Always use in combination with a battery. •3• 11. OPERATING INSTRUCTIONS WARNING: A SPARK NEAR THE BATTERY MAY CAUSE AN EXPLOSION. NOTE: This charger is equipped with an auto-start feature. Current will not be supplied to the battery clamps until a battery is properly connected. The clamps will not spark if touched together. CHARGING A BATTERY IN THE VEHICLE 1. Turn off all the vehicle’s accessories. 2. Keep the hood open. 3. Clean the battery terminals. 4. Place the charger on a dry, non-flammable surface. 5. Lay the AC/DC cables away from any fan blades, belts, pulleys and other moving parts. 6. Connect the battery, following the precautions listed in sections 6 and 7. 7. Connect the charger to an electrical outlet. 8. Select the desired rate. 9. When charging is complete, disconnect the charger from the AC power, remove the clamp from the vehicle’s chassis, and then remove the clamp from the battery terminal. CHARGING A BATTERY OUTSIDE OF THE VEHICLE 1. Place battery in a well-ventilated area. 2. Clean the battery terminals. 3. Connect the battery, following the precautions listed in sections 6 and 7. 4. Connect the charger to the electrical outlet. 5. Select the desired rate. 6. When charging is complete, disconnect the charger from the AC power, disconnect the negative clamp, and finally the positive clamp. 7. A marine (boat) battery must be removed and charged on shore. BATTERY CHARGING TIMES Times are based on a 50% discharged battery and may change, depending on age and condition of battery. AUTOMATIC CHARGING When an Automatic Charge is performed, the charger switches to the maintain mode automatically after the battery is charged. ABORTED CHARGE If charging cannot be completed normally, charging will abort. When charging aborts, the charger’s output is shut off and the Bad Battery (red) LED will light. Do not continue attempting to charge this battery. Check the battery and replace, if necessary. DESULFATION MODE Desulfation could take 8 to 10 hours. If desulfation fails, charging will abort and the Bad Battery (red) LED will light. COMPLETION OF CHARGE Charge completion is indicated by the Charged/Maintaining (green) LED. When lit, the charger has switched to the maintain mode of operation. •4• MAINTAIN MODE (FLOAT MODE MONITORING) When the Charged/Maintaining (green) LED is lit, the charger has started maintain mode. In this mode, the charger keeps the battery fully charged by delivering a small current when necessary. If the charger has to provide its maximum maintain current for a continuous 12 hour period, it will go into abort mode (see Aborted Charge section). This is usually caused by a drain on the battery or the battery could be bad. Make sure there are no loads on the battery. If there are, remove them. If there are none, have the battery checked or replaced. MAINTAINING A BATTERY The unit charges and maintains 12V batteries, keeping them at full charge. NOTE: The maintain mode technology allows you to safely charge and maintain a healthy battery for extended periods of time. However, problems with the battery, electrical problems in the vehicle, improper connections or other unanticipated conditions could cause excessive current draws. As such, occasionally monitoring your battery and the charging process is required. USING THE ENGINE START SETTING Your battery charger can be used to jump start your car if the battery is low. Follow all safety instructions and precautions for charging your battery. Wear complete eye protection and clothing protection. WARNING: Using the ENGINE START setting WITHOUT a battery installed in the vehicle could cause damage to the vehicle’s electrical system. NOTE: If you have charged the battery and it still will not start your car, do not use the Engine Start setting, or it could damage the vehicle’s electrical system. Have the battery checked. 1. With the charger unplugged from the AC outlet, connect the charger to the battery, following the instructions given in Follow These Steps When Battery Is Installed In Vehicle. 2. With the charger plugged in and connected to the battery of the vehicle, set the Rate Selection to the Engine Start position. 3. Crank the engine until it starts or 3 seconds pass. If the engine does not start, wait 3 minutes before cranking again. NOTE: During extremely cold weather, or if the battery is under 2 volts, use the Boost setting for 5 minutes before cranking the engine. 4. If the engine fails to start, boost the battery for 5 more minutes before attempting to crank the engine again. 5. After the engine starts, unplug the AC power cord before disconnecting the battery clamps from the vehicle. NOTE: If the engine does turn over but never starts, there is not a problem with the starting system; there is a problem somewhere else with the vehicle. STOP cranking the engine until the other problem has been diagnosed and corrected. 12. MAINTENANCE AND CARE A minimal amount of care can keep your battery charger working properly for years. • Clean the clamps each time you are finished charging. Wipe off any battery fluid that may have come in contact with the clamps to prevent corrosion. • Occasionally cleaning the case of the charger with a soft cloth will keep the finish shiny and help prevent corrosion. • Coil the input and output cords neatly when storing the charger. This will help prevent accidental damage to the cords and charger. • Store the charger unplugged from the AC power outlet in an upright position. • Store inside, in a cool, dry place. Do not store the clamps clipped together, on the handle, on or around metal, or clipped to the cables. 13. TROUBLESHOOTING PROBLEM Battery clamps do not spark when touched together. Three LEDs come on for 2 seconds, then turn off. POSSIBLE CAUSE SOLUTION The charger is equipped with an auto- No problem; this is a normal start feature. It will not supply current condition. to the battery clamps until a battery is properly connected. The clamps will not spark if touched together. The charger is plugged into an AC outlet. No problem; this is normal. The charger was recently unplugged This is normal. Allow a few minutes from an AC outlet. for the charger to shut off. •5• PROBLEM The charger will not turn on when properly connected. Short or no start cycle when cranking engine. POSSIBLE CAUSE AC outlet is dead. SOLUTION Check for open fuse or circuit breaker supplying AC outlet. Poor electrical connection. Check power cord and extension cord for loose fitting plug. No power at receptacle. Check for open fuse or circuit breaker supplying AC outlet. AC cord and/or extension cord is loose. Check power cord and extension cord for loose fitting plug. The clamps are not making a good connection. Check for poor connection at battery and frame. Failure to wait 3 minutes (180 seconds) between cranks. Wait 3 minutes of rest time before the next crank, to allow the battery and charger to cool down. The battery may be severely discharged. On a severely discharged battery, use the Boost setting for few minutes, to help assist in cranking. The battery is drawing more than the Crank time varies with the amount of Engine Start rate. current drawn. If cranking draws more than the Engine Start rate, crank time may be less than 3 seconds. The charger may be overheated. The red LED is lit. The thermal protector may have tripped and needs a little longer to close. Make sure the charger vents are not blocked. Wait and try again. The battery voltage is still below 10V The battery may be defective. Make (for a 12V battery) or 5V (for a 6V sure there are no loads on the battery) after 2 hours of charging. battery. If there are, remove them. (or) If there are none, have the battery In maintain mode, the output current is checked or replaced. more than 2.0A for 12 hours. Desulfation was unsuccessful. The battery may be defective. Have battery checked or replaced. Lack of progress is detected and The battery may be overheated. If so, battery voltage is below 14.2V (for a allow the battery to cool. The battery 12V battery) or 7.1V (for a 6V battery). may be too large or have a short circuit. Have battery checked or replaced. The battery’s initial voltage is below The battery capacity is too low, or the 12.2V (for a 12V battery) or 6.1V (for battery is too old. Have it checked or a 6V battery) and the total input is replaced. less than 1.5 Ah. The battery voltage drops to below 12.2V (for a 12V battery) or 6.1V (for a 6V battery) in Maintain Mode. •6• The battery won’t hold a charge. May be caused by a drain on the battery or the battery could be bad. Make sure there are no loads on the battery. If there are remove them. If there are none, have the battery checked or replaced. 14. BEFORE RETURNING FOR REPAIRS For information about troubleshooting, contact customer service for assistance: [email protected] | www.batterychargers.com | or call 1-800-621-5485 Return products under warranty to your local AutoZone store. 15. LIMITED WARRANTY SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE, MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED WARRANTY TO THE ORIGINAL RETAIL PURCHASER OF THIS PRODUCT. THIS LIMITED WARRANTY IS NOT TRANSFERABLE OR ASSIGNABLE. Schumacher Electric Corporation (the “Manufacturer”) warrants this charger for two (2) years from the date of purchase at retail against defective material or workmanship that may occur under normal use and care. If your unit is not free from defective material or workmanship, Manufacturer’s obligation under this warranty is solely to repair or replace your product with a new or reconditioned unit at the option of the Manufacturer. It is the obligation of the purchaser to forward the unit, along with proof of purchase and mailing charges prepaid to the Manufacturer or its authorized representatives in order for repair or replacement to occur. Manufacturer does not provide any warranty for any accessories used with this product that are not manufactured by Schumacher Electric Corporation and approved for use with this product. This Limited Warranty is void if the product is misused, subjected to careless handling, repaired, or modified by anyone other than Manufacturer or if this unit is resold through an unauthorized retailer. Manufacturer makes no other warranties, including, but not limited to, express, implied or statutory warranties, including without limitation, any implied warranty of merchantability or implied warranty of fitness for a particular purpose. Further, Manufacturer shall not be liable for any incidental, special or consequential damage claims incurred by purchasers, users or others associated with this product, including, but not limited to, lost profits, revenues, anticipated sales, business opportunities, goodwill, business interruption and any other injury or damage. Any and all such warranties, other than the limited warranty included herein, are hereby expressly disclaimed and excluded. Some states do not allow the exclusion or limitation of incidental or consequential damages or length of implied warranty, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and it is possible you may have other rights which vary from this warranty. THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY AND THE MANUFACTURER NEITHER ASSUMES OR AUTHORIZES ANYONE TO ASSUME OR MAKE ANY OTHER OBLIGATION TOWARDS THE PRODUCT OTHER THAN THIS WARRANTY. Distributed by: Best Parts, Inc., Memphis, TN 38103 •7• Cargador de baterías automático MANUAL DEL USUARIO POR FAVOR CONSERVE ESTE MANUAL DEL USUARIO Y LEALO ANTES DE CADA USO. En este manual le explica cómo utilizar el cargador de batería de manera segura y confiable. Por favor, lea y siga las siguientes instrucciones y precauciones. 1. 102-9 INSTRUCCIONES IMPORTANTES DE SEGURIDAD – GUARDE ESTAS INSTRUCCIONES. 1.1 GUARDE ESTAS INSTRUCCIONES – Este manual contiene instrucciones operativas y de seguridad de importancia. 1.2 Manténgase alejado de los niños. 1.3 No exponga el cargador a la lluvia o a la nieve. 1.4 El uso de un accesorio no recomendado o suministrado por el fabricante del cargador de baterías puede provocar riesgo de incendio, descarga eléctrica o lesiones a personas. 1.5 Para reducir el riesgo de daños al enchufe o cable eléctrico, jale del enchufe en lugar de jalar del cable al desconectar el cargador. 1.6 No se debe utilizar un alargador a menos que resulte absolutamente necesario. El uso de un alargador 1.7 1.8 1.9 1.10 1.11 2. inadecuado puede provocar riesgo de incendio o descarga eléctrica. En caso de que deba utilizarse un alargador, asegúrese de que: • Los pasadores en el enchufe del alargador posean el mismo número, tamaño y forma que aquellos presentes en el enchufe del cargador. • El alargador se encuentre correctamente conectado y en buenas condiciones eléctricas; y • El tamaño del cable sea lo suficientemente extenso para el amperaje en CA del cargador como se especifica en la sección 8. No utilice el cargador si el mismo posee un enchufe o cable dañado; substituya el cable o el enchufe inmediatamente por una persona calificada en el ramo. No utilice el cargador si el mismo recibió un golpe fuerte, si se cayó o si sufrió daños de cualquier otra forma; hágalo revisar por una persona capacitada que efectúe reparaciones. No desarme el cargador; hágalo revisar por una persona capacitada que efectúe reparaciones cuando necesite servicio de mantenimiento o una reparación. Volver a ensamblar el cargador en forma incorrecta puede provocar riesgo de incendio o descarga eléctrica. Para reducir el riesgo de descarga eléctrica, desenchufe el cargador del tomacorriente antes de intentar llevar a cabo cualquier actividad de mantenimiento o limpieza. El simple apagado de los controles no reducirá este riesgo. ADVERTENCIA: RIESGO DE GASES EXPLOSIVOS. a. RESULTA PELIGROSO TRABAJAR EN FORMA CERCANA A UNA BATERÍA DE PLOMO. LAS BATERÍAS GENERAN GASES EXPLOSIVOS DURANTE SU NORMAL FUNCIONAMIENTO. POR ESTE MOTIVO, RESULTA DE SUMA IMPORTANCIA QUE SIGA LAS INSTRUCCIONES CADA VEZ QUE UTILIZA EL CARGADOR. b. Para reducir el riesgo de explosión de una batería, siga estas instrucciones y aquellas publicadas por el fabricante de la batería y por el fabricante de cualquier equipo que intente utilizar en la proximidad de la batería. Revise las pautas de precaución en estos productos y en el motor. PRECAUCIONES DE SEGURIDAD PERSONAL 2.1 Considere la idea de que alguna persona se encuentre cerca suyo para poder ayudarlo cuando trabaje en forma cercana a una batería de plomo-ácido. 2.2 Cuente con una gran cantidad de agua potable y jabón a mano en caso de que el ácido de la batería tenga contacto con su piel, ropa u ojos. Utilice protección visual y corporal completa, incluyendo gafas de seguridad y prendas de protección. Evite tocar sus ojos mientras trabaje en forma cercana a la batería. 2.4 Si el ácido de la batería tiene contacto con su piel o su ropa, lave de inmediato el área afectada con agua y jabón. En caso de que ingrese ácido en un ojo, sumerja el mismo de inmediato bajo agua potable corriente por al menos 10 minutos y obtenga atención médica en forma inmediata. 2.3 •8• 2.5 NUNCA fume o permita la presencia de chispas o llamas en la proximidad de una batería o motor. 2.6 Tenga especial cuidado para reducir el riesgo de dejar caer una herramienta de metal sobre la batería. Esto podría provocar chispas o un cortocircuito en la batería o en cualquier otra pieza eléctrica que podría provocar una explosión. 2.7 No utilice elementos personales de metal tales como anillos, pulseras, collares y relojes al trabajar con una batería de plomo-ácido. Una batería de plomo-ácido puede producir una corriente de cortocircuito lo suficientemente elevada como para soldar un anillo o provocar efectos similares sobre el metal, causando una quemadura de gravedad. 2.8 Utilice este cargador solamente para cargar baterías recargables de 12V de tipo PLOMO-ÁCIDO (estándar, AGM o GEL). Este cargador no está destinado a suministrar energía a sistemas eléctricos de baja tensión más que en una aplicación de un motor de arranque. No utilice este cargador de batería para cargar baterías de pila seca que por lo general se utilizan con artefactos domésticos. Estas baterías podrían explotar y provocar lesiones a personas o daño a la propiedad. 2.9 NUNCA cargue una batería congelada. 3. PREPARACIÓN PARA LA CARGA 3.1 Si resulta necesario extraer la batería del vehículo para cargarla, siempre retire el terminal con descarga 3.2 3.3 3.4 3.5 3.6 4. a tierra en primer lugar. Asegúrese de que todos los accesorios en el vehículo se encuentren apagados para evitar la formación de arcos eléctricos. Asegúrese de que el área que rodea a la batería se encuentre bien ventilada mientras se carga la batería. Limpie los terminales de la batería antes de cargar la batería. Durante la limpieza, evite que la corrosión producida por aire tenga contacto con sus ojos. Agregue agua destilada a cada pila hasta que el ácido de la batería alcance el nivel especificado por el fabricante de la batería. No provoque derrames. En lo que concierne a baterías que no cuentan con tapas extraíbles para pilas, tales como baterías de plomo-ácido reguladas por válvulas (VRLA, por sus siglas en inglés), siga cuidadosamente las instrucciones de recarga del fabricante. Lea, comprenda y siga todas las instrucciones para el cargador, la batería, el vehículo y cualquier equipo que se utilice cerca de la batería y el cargador. Controle todas las precauciones específicas establecidas por el fabricante de la batería al realizar la carga, así también como los índices de carga recomendados. Determine la tensión de la batería al consultar el manual del usuario del vehículo y asegúrese de que el interruptor de selección de la tensión de salida se encuentre establecido en la tensión correcta (en su caso). Si el cargador posee un índice de carga ajustable, cargue la batería en el menor índice en primer lugar. UBICACIÓN DEL CARGADOR 4.1 Ubique el cargador a la mayor distancia posible de la batería como lo permitan los cables de CC. 4.2 Nunca ubique el cargador directamente por encima de la batería que se carga; los gases de la batería corroerán y dañarán el cargador. 4.3 Nunca permita que el ácido de la batería gotee sobre el cargador al leer el peso específico del electrolito o al cargar la batería. 4.4 No utilice el cargador en un área cerrada o restrinja la ventilación en cualquier forma. 4.5 No ubique la batería encima del cargador. 5. PRECAUCIONES DE CONEXIÓN EN CC 5.1 Conecte y desconecte las pinzas de salida CC. sólo después de haber establecido todos los interruptores del cargador a la posición de “apagado” (si es aplicable) y de haber desconectado el enchufe de C.A. del tomacorriente eléctrico. Nunca permita que las pinzas tengan contacto entre sí. 5.2 Sujete las pinzas a la batería y al chasis, como se indica en en las secciones 6 y 7. •9• 6. SIGA ESTOS PASOS CUANDO LA BATERÍA ESTÉ COLOCADA EN EL VEHÍCULO 6.8 ADVERTENCIA: UNA CHISPA PROVOCADA CERCA DE LA BATERÍA PUEDE CAUSAR LA EXPLOSIÓN DE LA BATERÍA. PARA REDUCIR EL RIESGO DE PROVOCAR CHISPAS CERCA DE LA BATERÍA: Ubique los cables de C.A. y C.C. para reducir el riesgo de daños a la cubierta, a la puerta y a las piezas móviles o calientes del motor. Manténgase alejado de las paletas del ventilador, correas, poleas y otras piezas que podrían provocar lesiones. Verifique la polaridad de los bornes de la batería. El borne POSITIVO (POS, P, +) de la batería generalmente posee un diámetro mayor al borne NEGATIVO (NEG, N, -). Determine qué borne de la batería hace descarga a tierra (se encuentra conectado) con el chasis. Si el borne negativo hace descarga a tierra con el chasis (como en la mayor parte de los vehículos), ver el paso 6.5. Si el borne positivo hace descarga a tierra con el chasis, ver el paso 6.6. En un vehículo con descarga a tierra por borne negativo, conecte el gancho POSITIVO (ROJO) del cargador de batería al borne POSITIVO (POS, P, +) sin descarga a tierra de la batería. Conecte el gancho NEGATIVO (NEGRO) al chasis del vehículo o al bloque motor alejado de la batería. No conecte el gancho al carburador, líneas de combustible o cuerpos metálicos. Conecte a una pieza metálica de calibre grueso del marco o del bloque motor. En un vehículo con descarga a tierra por borne positivo, conecte el gancho NEGATIVO (NEGRO) del cargador de batería al borne NEGATIVO (NEG, N, -) sin descarga a tierra de la batería. Conecte el gancho POSITIVO (ROJO) al chasis del vehículo o al bloque motor alejado de la batería. No conecte al carburador, líneas de combustible o cuerpos metálicos. Conecte a una pieza metálica de calibre grueso del marco o del bloque motor. Al desconectar el cargador, apague todos los interruptores (en su caso), desconecte el cable de C.A., retire el gancho del chasis del vehículo y luego retire el gancho del terminal perteneciente a la batería. Vea Instrucciones de Operación para duración de la carga. 7. SIGA ESTOS PASOS CUANDO LA BATERÍA SE ENCUENTRE FUERA DEL VEHÍCULO 6.1 6.2 6.3 6.4 6.5 6.6 6.7 7.1 7.2 7.3 7.4 7.5 7.6 7.7 8. ADVERTENCIA: UNA CHISPA PROVOCADA CERCA DE LA BATERÍA PUEDE CAUSAR LA EXPLOSIÓN DE LA BATERÍA. PARA REDUCIR EL RIESGO DE PROVOCAR CHISPAS CERCA DE LA BATERÍA: Verifique la polaridad de los bornes de la batería. El borne POSITIVO (POS, P, +) de la batería generalmente posee un diámetro mayor al borne NEGATIVO (NEG, N, -). Sujete al menos un cable aislado de batería de 24 pulgadas (61 cm) de largo con calibre 6 según el Calibre americano de cables (AWG, por sus siglas en inglés) al borne NEGATIVO (NEG, N, -) de la batería. Conecte el gancho POSITIVO (ROJO) del cargador al borne POSITIVO (POS, P, +) de la batería. Ubíquese junto con el extremo libre del cable que previamente sujetó al borne NEGATIVO (NEG, N, -) de la batería a la mayor distancia posible de la batería. Luego conecte el gancho NEGATIVO (NEGRO) del cargador al extremo libre del cable. No se ubique en posición frontal a la batería al realizar la conexión final. Al desconectar el cargador, siempre hágalo en forma inversa al procedimiento de conexión y realice la primera conexión tan lejos de la batería como sea posible. Una batería marina (para barcos) se debe retirar y cargar en tierra. Para realizar una carga a bordo se necesitan equipamientos especialmente diseñados para uso marino. CONEXIONES A TIERRA Y ENERGÍA DE CA Este cargador de batería está destinado a un uso en un circuito con tensión nominal de 120 V y posee un enchufe con descarga a tierra. El cargador debe poseer una descarga a tierra para reducir el riesgo de descargas eléctricas. El enchufe se debe conectar a un tomacorriente adecuadamente instalado y que cuente con descarga a tierra de acuerdo con todas las ordenanzas y códigos. Los pasadores del enchufe deben adaptarse al receptáculo (tomacorriente). No utilizar con un sistema que no posea descarga a tierra. 8.2 PELIGRO: Nunca altere el cable o enchufe de C.A. suministrado, si no se ajusta al tomacorriente, haga instalar un tomacorriente adecuado con descarga a tierra por medio de un electricista capacitado. Una conexión inadecuada puede provocar un riesgo de descarga eléctrica o electrocución. NOTA: De acuerdo a las Leyes Canadienses, el uso de un enchufe adaptador no es permitido en el Canada. El uso de un enchufe como adaptador no se recomienda y no debe ser utilizado Estados Unidos. 8.1 • 10 • 8.3 USO DE UN CABLE DE EXTENSIÓN El uso de una extensión no se recomienda. Si debe usar una extensión, siga estas pautas: • Las clavijas del enchufe del cable de extensión debe ser el mismo número, tamaño y forma que las del enchufe del cargador. • Asegúrese de que el cable de extensión esté conectado correctamente y en buenas condiciones eléctricas. • El tamaño del cable debe ser lo suficientemente extenso para el calibre de amperios del cargador de CA, como se especifica a continuación: Longitud del cable (pies) Calibre del cable AWG* *AWG-American Wire Gauge 9. 25 18 50 16 100 150 12 10 INSTRUCCIONES DE MONTAJE 9.1 Desenrede todos los cordones y extienda los cables antes de usar el cargador de baterías. 10. PANEL DE CONTROL INDICADORES LED LED CARGA (amarillo/naranja) encendido: El cargador está cargando la batería. LED CARGADO/MANTENIMIENTO (verde) encendido: La carga de la bateria está completa y que el cargador cambió a modo mantener. LED PINZAS INVERTIDAS/BATERÍA DEFECTUOSA (rojo) parpadea: Las conexiones están inversas. LED PINZAS INVERTIDAS/BATERÍA DEFECTUOSA (rojo) encendido: El cargador ha detectado un problema con la batería. Consulte Localización y Solución de Problemas para obtener más información. NOTA: Consulte la sección Instrucciones de Operación para obtener una descripción completa de los modos del cargador. SELECCIÓN DE VELOCIDAD Utilice este botón para establecer una de las siguientes selecciones: 6<>2A CARGA /MANTENIMIENTO – Para la carga de baterías pequeñas y grandes. El cargador se ajusta automáticamente la corriente de carga, basado en el tamaño de la batería, con el fin de cargar la batería completamente, eficiente y segura. No se recomienda para aplicaciones industriales. IMPULSAR – Esta configuración puede ser usada para impulso rápido antes de usar la característica de arranque del motor. No utilice esta opción para cargar la batería. ARRANQUE DE MOTOR – Proporcionar amplificadores adicionales para el arranque de un motor con una débil o agotado la batería. Siempre utilice en combinación con una batería. 11. INSTRUCCIONES DE OPERACIÓN ADVERTENCIA: Una chispa provocada cerca de la batería puede causar la explosión de la batería. NOTA: Este cargador está equipado con un auto-rectificador. La corriente no llegará a las pinzas de la batería hasta que la batería esté apropiadamente conectada. Significado, las pinzas no harán corto si se juntan una con otra. CARGA DE LA BATERÍA EN EL VEHÍCULO 1. Apague todos los accesorios del vehículo. 2. Mantenga el cofre abierto. 3. Limpie las terminales de la batería. 4. Coloque el cargador sobre una superficie seca y no inflamable. 5. Coloque los cables de CA / CC lejos de las aspas del ventilador, bandas, poleas y otras partes móviles. 6. Conectar la batería según las instrucciones que indicadas en las secciones 6 y 7. 7. Conecte el cargador a la toma de corriente. 8. Seleccione la velocidad deseada. 9. Cuando la carga está completa, desconecte el cargador de la alimentación de CA, retire la pinza del chasis del vehículo y quite la pinza de la terminal de la batería. • 11 • CARGA DE LA BATERÍA FUERA DEL VEHÍCULO 1. Coloque la batería un área bien ventilada. 2. Limpie las terminales de la batería. 3. Conectar la batería según las instrucciones que indicadas en las secciones 6 y 7. 4. Conecte el cargador a la toma de corriente. 5. Seleccione la velocidad deseada. 6. Cuando la carga está completa, desconecte el cargador de la corriente AC, desconecte la pinza negativa, y por último la pinza positiva. 7. Una batería marina (de barco) se debe retirar y cargar en tierra. TIEMPOS DE CARGA Los tiempos están basados en un 50% descargada batería y pueden cambiar, dependiendo de la edad y la condición de la batería. MODO DE CARGA AUTOMÁTICA Cuando se realiza una carga automática, el cargador cambia del maintain mode [modo de mantenimiento] automáticamente después que la batería se cargue. CARGA ANULADA Si no se puede completar la carga normalmente, la carga se anulará. Cuando la carga se interrumpe, la salida del cargador se apaga y la luz LED Batería Defectuosa (rojo) se iluminará. No continúe intentando cargar esta batería. Revise la batería y reemplácela si es necesario. MODO DE DESULFATACIÓN La desulfatación puede durar 8 a 10 horas. Si la desulfatación falla, la carga se abortará y luz LED Batería Defectuosa (rojo) se iluminará. FINALIZACIÓN DE LA CARGA La finalización de la carga se indica con el LED Cargado/Mantenimiento (verde). Cuando está encendido, el cargador ha pasado de modo de función a mantenimiento. MODO DE MANTENIMIENTO (MONITOREO A MODO DE FLOTE) Cuando la luz LED Cargado/Mantenimiento (verde) está encendido, quiere decir que pasó al modo de mantenimiento. En este modo el cargador mantiene la batería totalmente cargada mediante una pequeña corriente cuando corresponda. Si el cargador tiene que funcionar al máximo en corriente continua de mantenimiento a un periodo de 12 horas, se transladará al Modo de Interrumpir (véase la sección Carga Anulada). Esto es ocacionalmente causado por una pérdida de energía en la batería o la batería está dañada. Asegúrese que no escape de carga en la batería y si la hay evítela, en caso contrario, verifique o reémplace la batería. MANTENIENDO UNA BATERÍA La unidad carga y mantiene las baterías de 12 voltios, manteniéndolas a carga completa. NOTA: La tecnología de modo de mantenimiento le permite cargar de forma segura y mantener una batería en buen estado durante largos períodos de tiempo. Ahora, los problemas con la batería, problemas eléctricos del vehículo, conexiones equivocadas u otras condiciones que surgan, podrías causar absorsión de corriente excesiva. De modo que, ocasionalmente seguimiento de su batería y el proceso de carga se requiere. • 12 • UTILIZAR LA FUNCIÓN DE ENCENDIDO DE MOTOR El cargador de batería se puede utilizar para impulsar el auto si la batería está baja. Siga todas las instrucciones y precauciones de seguridad en la carga de la batería. Use protección para los ojos y ropa adecuada con protección. ¡ADVERTENCIA: UTILIZANDO LA FUNCIÓN DE ARRANQUE DEL MOTOR SIN LA BATERÍA INSTALADA EN EL VEHÍCULO, DAÑARÁ EL SISTEMA ELÉCTRICO! NOTA: Si usted ya ha cargado la batería y aún no arranca el auto, no utilice la opción de arranque, porque esto podría dañar el sistema eléctrico del vehículo. Haga revisar la batería. 1. Con el cargador desenchufado del tomacorriente de CA, conecte el cargador a la batería, siguiendo las instrucciones en Siga Estos Pasos Cuando La Batería Esté Colocada En El Vehículo. 2. Con el cargador enchufado y conectado a la batería del vehículo, ajuste la Velocidad de Carga a la posición de Arranque del Motor . 3. Déle arranque al motor hasta que se ponga en marcha o que pasen 3 segundos. Si el motor no arranca espere 3 minutos antes de intentarlo de nuevo. NOTA: Bajo clima frío extremo o si la batería es inferior a 2 volts, utilizar el ajuste Impulsar por 5 minutos antes de poner en marcha el motor. 4. Si el motor no arranca, utilizar el ajuste del Boost por 5 minutos más antes de darle arranque nuevamente. 5. Después de que el motor se puso en marcha, desenchufe el cable de alimentación de CA antes de desconectar las pinzas de la batería del vehículo. NOTA: Si el motor gira, pero no enciende, no existe un problema con el sistema de arranque, sino en cualquier otra parte del vehículo. DEJE de darle arranque al motor hasta que el otro problema se diagnostique y se corrija. 12. MANTENIMIENTO Y CUIDADO Con cuidados mínimos puede mantener el cargador de baterías funcionando correctamente durante años. • Limpie las pinzas cada vez que termine de usar el cargador. Limpie el fluido de la batería que podría haber estado en contacto con las pinzas para evitar la corrosión. • De vez en cuando, limpie la carcasa del cargador con un paño suave para conservar el acabado brillante y evitar la corrosión. • Enrolle los cables de entrada y salida cuidadosamente cuando almacene el cargador. Esto ayudará a evitar daños accidentales a los cables y el cargador. • Guarde el cargador desenchufado de la toma de alimentación de CA en posición vertical. • Debe conservarse en un lugar fresco y seco. No lo enrede las pinzas en el mango, no las una, ni en metal, tampoco sujete a los cables. 13. LOCALIZACIÓN Y SOLUCIÓN DE PROBLEMAS PROBLEMA CAUSA POSIBLE Las pinzas de la batería no hacen Este cargador está equipado corto al juntarse una con otra. con un auto-rectificador. Este no permitirá paso de corriente si las pinzas de la batería no están conectadas en forma correcta. Significado, las pinzas no harán corto si se juntan una con otra. Las tres luces LED encienden por El cargador se conecta al 2 segundos, después se apagan. tomacorriente de CA. SOLUCIÓN No hay problema; es una condición normal. No hay problema; es una condición normal. El cargador se desconecta Esto es normal. Espere unos recientemente de una toma de CA. minutos para que el cargador se apagan. • 13 • PROBLEMA El cargador no se enciende incluso al estar bien conectado. Ciclo reducido o sin inicio al arrancar el motor. CAUSA POSIBLE Tomacorriente de CA fuera de funcionamiento. SOLUCIÓN Controle la posible presencia de fusibles abiertos o disyuntores que suministren energía al tomacorriente de CA. Conexión eléctrica deficiente. Revise el cable de extensión para cable y enchufe suelta. Verifique la posible presencia de fusibles abiertos o disyuntores que suministren energía al tomacorriente de CA. No hay electricidad en el tomacorriente. Cable de CA o alargador suelto. Verifique la posible pérdida del enchufe perteneciente a los cables de alimentación o al alargador. Las pinzas no se encuentran bien Verifique la posible presencia de conectados. una conexión defectuosa en la batería y en el bastidor. No espera 3 minutos (180 segundos) entre los arranques. Aguarde 3 minutos en tiempo de descanso antes del próximo arranque. La batería podría encontrarse severamente descargada. Con batería muy descargada, utilice ajuste de Impulsar por 5 minutos, para ayudar a ayudar en el arranque. Consumo mayor a el índice de arranque del motor. El tiempo de arranque varía según la cantidad de corriente consumida. Si el arranque consume más el índice de arranque del motor, el tiempo de arranque podría ser menor a 3 segundos. El cargador podría encontrarse en El protector térmico podría estado de recalentamiento. encontrarse desconectado y necesitar un mayor tiempo de descanso. Asegúrese de que los ventiladores del cargador no se encuentren bloqueados. Aguarde un momento y pruebe nuevamente. • 14 • PROBLEMA El LED rojo se ilumina. CAUSA POSIBLE El voltaje de la batería todavía está debajo de 10V (para una batería 12V) o de 5V (para una batería 6V) después de 2 horas de carga. (o) En el modo de mantenimiento, la corriente de salida es de más de 2,0 A durante 12 horas. SOLUCIÓN La batería puede estar defectuosa. Asegúrese de que no hay cargas en la batería. Si hay eliminarlos. Si no hay ninguno, verifíque o reempláce la batería. La batería no puede desulfatada. La batería puede estar defectuosa. Verifíquela o reemplácela. Se detecta la falta de progreso y voltaje de la batería está por debajo de 14,2V (para una batería 12V) o de 7,1V (para una batería 6V). La batería se puede sobrecalienta. Si es así, deje que la batería se enfríe. La batería puede ser demasiado grande o tener un circuito en corto. Verifíquela o reemplácela. Voltaje inicial de la batería está por debajo de 12,2V (para una batería 12V) o de 6,1V (para una batería 6V) y la entrada total es de menos de 1,5 Ah. La capacidad de la batería es demasiado bajo o la batería es demasiado antigua. Verifíquela o reemplácela. El voltaje de la batería cae por debajo de 12.2V (para una batería 12V) o de 6,1V (para una batería 6V) en el modo de mantenimiento. La batería no mantiene la carga. Puede ser causada por una batería descargada o la batería podría ser malo. La batería puede estar defectuosa. Asegúrese de que no hay cargas en la batería. Si hay eliminarlos. Si no hay ninguno, verifíque o reempláce la batería. 14. ANTES DE DEVOLVER A REPARACIONES Si desea obtener más información sobre la solución de problemas, póngase en contacto con el departamento de servicio al cliente para recibir asistencia: [email protected] | www.batterychargers.com | o llame 1-800-621-5485 Devuelva producto para reparación bajo garantía a su tienda de AutoZone local. • 15 • 15. GARANTÍA LIMITADA SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE, MOUNT PROSPECT, IL 60056-2179, REALIZA LA PRESENTE GARANTÍA LIMITADA AL COMPRADOR MINORISTA ORIGINAL DE ESTE PRODUCTO. LA PRESENTE GARANTÍA LIMITADA NO PUEDE TRANSFERIRSE NI CEDERSE. Schumacher Electric Corporation (el “Fabricante”) otorga garantía por esta unidad por dos (2) años contados a partir de la fecha de compra, contra cualquier material defectuoso o de mano de obra de la unidad que pudieran surgir durante su uso y bajo cuidado normal. Si su unidad cuenta con material defectuoso o defectos de mano de obra, la obligación de los Fabricantes, conforme a la presente garantía, será simplemente reparar o sustituir el producto por uno nuevo o por una unidad reparada, a elección del fabricante. Es la obligación del comprador enviar la unidad con comprobante de compra y los gastos de envío prepagos al Fabricante o a sus representantes autorizados para que estos reparen o reemplacen el producto. El Fabricante no presta garantía por lo accesorios utilizados con este producto que no sean los fabricados por Schumacher Electric Corporation y que no estén aprobados para su uso con este producto. La presente Garantía Limitada será nula si el producto se utiliza en forma errónea, se trata de manera inadecuada, es reparado o modificado por personas que nos sean el Fabricante o si esta unidad es revendida a través de un vendedor minorista no autorizado. El Fabricante no realiza ninguna otra garantía, incluidas, a título enunciativo, las garantías expresas, implícitas o legales, incluidas, a modo de ejemplo, las garantías implícitas de comerciabilidad o adecuación a un fin específico. Asimismo, el Fabricante no será responsable ante reclamos por daños accidentales, especiales ni directos en los que incurran los compradores, usuarios u otras personas asociadas al producto, incluidas, a título enunciativo, los ingresos y ganancias no percibidas, ventas anticipadas, oportunidades comerciales, el buen nombre, la interrupción de la actividad comercial o cualquier otro daño que haya provocado. Todas las garantías, excepto la garantía limitada incluida en el presente, por medio de la presente, quedan expresamente anuladas y excluidas. Algunos estados no permiten la exclusión ni la limitación de los daños accidentales ni directos o el plazo de garantía implícita, por lo que las limitaciones o exclusiones mencionadas anteriormente podrían no corresponder con su caso. La presente garantía le otorga derechos legales específicos y es probable que usted cuente con otros derechos que podrían diferir de los incluidos en la presente garantía. LA PRESENTE GARANTÍA LIMITADA ES LA ÚNICA GARANTÍA LIMITADA EXPRESA Y EL FABRICANTE NO ASUME NI AUTORIZA A NADIE A ASUMIR O A ADQUIRIR NINGUNA OTRA OBLIGACIÓN RESPECTO DEL PRODUCTO QUE NO SEA LA PRESENTE GARANTÍA. Distribuido por: Best Parts, Inc., Memphis, TN 38103 • 16 •
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Fully automatic operation - just connect it and forget it
- Microprocessor-controlled charging for optimal battery performance
- Multi-stage charging algorithm for faster, more efficient charging
- Reverse polarity protection to prevent damage to the charger and battery
- Spark-proof design for added safety
- Overload and short-circuit protection
- Easy-to-read LED indicators for charging status
Related manuals
Frequently Answers and Questions
Can I use the Schumacher Duralast DL-75D Automatic Battery Charger to charge my lawnmower battery?
Yes, the DL-75D is suitable for charging 12-volt lead-acid batteries commonly used in lawnmowers.
Does the DL-75D have a reverse polarity protection feature?
Yes, the DL-75D is equipped with reverse polarity protection to prevent damage to the charger and battery in case the terminals are accidentally reversed.
What type of batteries can I charge with the DL-75D?
The DL-75D is designed to charge 12-volt lead-acid batteries, including standard, AGM, and gel batteries.
How long does it take to charge a battery with the DL-75D?
The charging time depends on the size and condition of the battery being charged. Refer to the user manual for specific charging times.
Can I leave the DL-75D connected to the battery indefinitely?
No, it is not recommended to leave the charger connected to the battery for extended periods. Once the battery is fully charged, disconnect the charger to avoid overcharging.