Yealink Meeting Server V10.23.0.5 Installation guide

This chapter provides the hardware recommendations of your server.
Feature
CPU
Description
Intel Xeon E5-2600 series (Haswell architecture) or similar
Xeon processors from 2012 or later, 2.3 GHz or faster.
A CPU should match 4 RAM.
RAM
Hard Drive Space
4GB/DDR3/2133MHz/ECC or higher
8GB/DDR4/2400MHz/ECC or higher
300GB or higher

Network

Gigabit Ethernet connectivity is strongly recommended.
In general, you can expert 1 Mbps in a one-way 720P
video call. And you can expert 2 Mbps in a one-way
1080P video call.
Capacity is dependent on server specifications. As a general
indication, using our recommended hardware (Intel Haswell,
10 cores, 2.3 GHz) YMS can connect:
Capacity


The maximum concurrent calls=total CPU
cores*frequency.
Up to extra 10 audio-only calls at 64 kbps.
Servers that are older, have slower processors, or have fewer
CPUs, will have a lower overall capacity.
For example, if you want to initiate 20-way 1080P concurrent calls or 40-way 720P concurrent
calls, the following hardware is recommended.
CPU
Memory
2 Intel Xeon Processor E5-2620V4, eight cores and sixteen
threads, 2.1GHz 20M 8.0GT/s 85W or higher
8 8GB/DDR4/2400MHz/ECC or higher
If you want to initiate 40-way 1080P concurrent calls or 80-way 720P concurrent calls, the
following hardware is recommended.
CPU
Memory
2 Intel Xeon Processor E5-2680V4, fourteen cores and
twenty-eight threads, 2.4GHz 35M 9.6GT/s 120W or higher
8 8GB/DDR4/2400MHz/ECC or higher
Users should pay attention to the following points before installation:

The installation workstation is CentOS 7.0 or later.

The Yealink Meeting Server application is saved at the path Computer->usr->local.

The disk partition of mcudata folder should be 512G and the root folder should be 256G.
The installation of 10.23.0.5 version is introduced as an example.
To install Yealink Meeting Server application (log into CentOS by the root account):
1.
Enter terminal.
2.
Run the command as below:
Cd /usr/local
Tar -xzvf Apollo_10.23.0.5.tar.gz
Cd /usr/local/apollo_install/
./install.sh
After you finish the installation, it will prompt “Install Success!!!”.
After you finish the installation, you will enter the setup wizard.
When you finish the configuration of the current page in the setup wizard, click Next to enter
another page.
To complete the setup wizard:
1.
In the setup wizard, configure network settings.
If the server uses two adapters and two adapters are deployed in an enterprise’s internal
network, you should configure static NAT to ensure devices from the public network can
access to the server.
Enter the native domain
name. If you fail to log into
Yealink Meeting Server by
domain name, you should use
the server IP address to log in.
Configure the NAT public
address.
Specify routing rules for external
network.
Specify routing rules for all
network segments in your
enterprise.
2.
Set the date and time (e.g., set the time zone and enable the daylight saving time).
3.
Edit the login password and email of enterprise administrator.
The email is used to edit login password and receive a warning from the server.
4.
Enter the license number to activate enterprise administrator account.
5.
Set SMTP mailbox.
The email is used to send account information, send invitations to conference and so on.
Enable connection
security
6.
Click OK to complete the setup wizard.
Enter test email to test
whether the SMTP
mailbox you set is
available.