Miller BIG BLUE TURBO User Owner’s Manual

OM-4420
212 049K
October 2004
Processes
Stick (SMAW) Welding
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
TIG (GTAW) Welding
Air Carbon Arc (CAC-A)
Cutting and Gouging
Description
Engine Driven Welding Generator
Big Blue Turbo

Visit our website at
www.MillerWelds.com
From Miller to You
Thank you and congratulations on choosing Miller. Now you can get
the job done and get it done right. We know you don’t have time to do
it any other way.
That’s why when Niels Miller first started building arc welders in 1929,
he made sure his products offered long-lasting value and superior
quality. Like you, his customers couldn’t afford anything less. Miller
products had to be more than the best they could be. They had to be the
best you could buy.
Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.
This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.
We’ve made installation and operation quick
and easy. With Miller you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will
help you figure out what the problem is. The
Miller is the first welding parts list will then help you to decide the
equipment manufacturer in exact part you may need to fix the problem.
the U.S.A. to be registered to
the ISO 9001:2000 Quality Warranty and service information for your
System Standard.
particular model are also provided.
Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor to receive the latest full
line catalog or individual catalog sheets. To locate your nearest
distributor or service agency call 1-800-4-A-Miller, or visit us at
www.MillerWelds.com on the web.
Mil_Thank 7/03
Working as hard as you do
− every power source from
Miller is backed by the most
hassle-free warranty in the
business.
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Engine Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. Compressed Air Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-7. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-8. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Signification des symboles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Dangers relatifs au soudage à l’arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Dangers existant en relation avec le moteur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4. Dangers liés à l’air comprimé . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance . . . . . .
2-6. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7. Information sur les champs électromagnétiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Weld, Power, And Engine Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Sound Level Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Dimensions, Weights, And Operating Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Stick And MIG Volt-Ampere Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5. DC TIG Volt-Ampere Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6. Fuel Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7. Duty Cycle And Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8. Generator AC Power Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-9. Manufacturing Rating Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Installing Welding Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Mounting Welding Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. Installing Optional Spark Arrestor Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4. Activating The Dry Charge Battery (If Applicable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-5. Connecting The Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6. Using The Optional Battery Disconnect Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-7. Engine Prestart Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-8. Connecting To Weld Output Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-9. Selecting Weld Cable Sizes* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-10. Connecting To Remote 14 Receptacle RC14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − OPERATING THE WELDING GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1. Controls (See Section 6-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2. Description Of Controls (See Section 6-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3. Process/Contactor Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-4. Using Remote Voltage/Amperage Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − OPERATING AUXILIARY EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1. 120 Volt And 240 Volt Receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2. Optional Generator Power Receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 8 − ENGINE/GENERATOR MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1. Routine Engine/Generator Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-2. Engine Maintenance Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-3. Servicing Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
2
3
3
4
4
4
5
5
5
6
7
7
8
8
9
9
10
10
10
10
11
12
12
13
13
14
15
15
16
17
18
19
19
20
21
22
23
24
24
25
26
27
28
28
29
30
30
32
33
TABLE OF CONTENTS
8-4. Inspecting/Cleaning Optional Spark Arrestor Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-5. Adjusting Engine Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-6. Servicing Engine Fuel And Lubrication Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-7. Engine/Generator Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9 − TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-1. Troubleshooting Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 10 − ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 11 − RUN-IN PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-1. Wetstacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-2. Run-In Procedure Using Load Bank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-3. Run-In Procedure Using Resistance Grid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 12 − GENERATOR POWER GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 13 − SELECTING AND PREPARING
TUNGSTEN ELECTRODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13-1. Selecting Tungsten Electrode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13-2. Preparing Tungsten For AC Or DC Electrode Positive (DCEP) Welding . . . . . . . . . . . . . . . . . . . . . . . .
13-3. Preparing Tungsten For DC Electrode Negative (DCEN) Welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 14 − GUIDELINES FOR TIG WELDING (GTAW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-1. Positioning The Torch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-2. Torch Movement During Welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-3. Positioning Torch Tungsten For Various Weld Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 15 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
35
36
37
38
38
42
44
44
45
46
47
54
54
55
55
56
56
56
57
58
SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING
rom _nd_10/02
Warning: Protect yourself and others from injury — read and follow these precautions.
1-1. Symbol Usage
Means Warning! Watch Out! There are possible hazards
with this procedure! The possible hazards are shown in
the adjoining symbols.
Marks a special safety message.
Means “Note”; not safety related.
This group of symbols means Warning! Watch Out! possible
ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.
Consult symbols and related instructions below for necessary actions
to avoid the hazards.
1-2. Arc Welding Hazards
Use only well-maintained equipment. Repair or replace damaged parts at
once. Maintain unit according to manual.
Wear a safety harness if working above floor level.
Keep all panels and covers securely in place.
Only qualified persons should install, operate, maintain, and repair this unit.
Clamp work cable with good metal-to-metal contact to workpiece or worktable as near the weld as practical.
During operation, keep everybody, especially children, away.
Insulate work clamp when not connected to workpiece to prevent contact
with any metal object.
Do not connect more than one electrode or work cable to any single weld
output terminal.
The symbols shown below are used throughout this manual to
call attention to and identify possible hazards. When you see the
symbol, watch out, and follow the related instructions to avoid the
hazard. The safety information given below is only a summary of
the more complete safety information found in the Safety Standards listed in Section 1-7. Read and follow all Safety Standards.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks or
severe burns. The electrode and work circuit is electrically
live whenever the output is on. The input power circuit and
machine internal circuits are also live when power is on. In semiautomatic or
automatic wire welding, the wire, wire reel, drive roll housing, and all metal
parts touching the welding wire are electrically live. Incorrectly installed or
improperly grounded equipment is a hazard.
Do not touch live electrical parts.
Wear dry, hole-free insulating gloves and body protection.
Insulate yourself from work and ground using dry insulating mats or covers
big enough to prevent any physical contact with the work or ground.
Do not use AC output in damp areas, if movement is confined, or if there is a
danger of falling.
Use AC output ONLY if required for the welding process.
If AC output is required, use remote output control if present on unit.
Additional safety precautions are required when any of the following electrically hazardous conditions are present: in damp locations or while wearing
wet clothing; on metal structures such as floors, gratings, or scaffolds;
when in cramped positions such as sitting, kneeling, or lying; or when there
is a high risk of unavoidable or accidental contact with the workpiece or
ground. For these conditions, use the following equipment in order presented: 1) a semiautomatic DC constant voltage (wire) welder, 2) a DC manual
(stick) welder, or 3) an AC welder with reduced open-circuit voltage. In most
situations, use of a DC, constant voltage wire welder is recommended.
And, do not work alone!
Disconnect input power or stop engine before installing or servicing this
equipment. Lockout/tagout input power according to OSHA 29 CFR
1910.147 (see Safety Standards).
Properly install and ground this equipment according to its Owner’s Manual
and national, state, and local codes.
Always verify the supply ground — check and be sure that input power cord
ground wire is properly connected to ground terminal in disconnect box or
that cord plug is connected to a properly grounded receptacle outlet.
When making input connections, attach proper grounding conductor first −
double-check connections.
Frequently inspect input power cord for damage or bare wiring — replace
cord immediately if damaged — bare wiring can kill.
Turn off all equipment when not in use.
Do not use worn, damaged, undersized, or poorly spliced cables.
Do not drape cables over your body.
If earth grounding of the workpiece is required, ground it directly with a separate cable.
Do not touch electrode if you are in contact with the work, ground, or another electrode from a different machine.
SIGNIFICANT DC VOLTAGE exists in inverters after stopping engine.
Stop engine on inverter and discharge input capacitors according to
instructions in Maintenance Section before touching any parts.
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing these fumes
and gases can be hazardous to your health.
Keep your head out of the fumes. Do not breathe the fumes.
If inside, ventilate the area and/or use exhaust at the arc to remove welding
fumes and gases.
If ventilation is poor, use an approved air-supplied respirator.
Read the Material Safety Data Sheets (MSDSs) and the manufacturer’s
instructions for metals, consumables, coatings, cleaners, and degreasers.
Work in a confined space only if it is well ventilated, or while wearing an airsupplied respirator. Always have a trained watchperson nearby. Welding
fumes and gases can displace air and lower the oxygen level causing injury
or death. Be sure the breathing air is safe.
Do not weld in locations near degreasing, cleaning, or spraying operations.
The heat and rays of the arc can react with vapors to form highly toxic and
irritating gases.
Do not weld on coated metals, such as galvanized, lead, or cadmium plated
steel, unless the coating is removed from the weld area, the area is well
ventilated, and if necessary, while wearing an air-supplied respirator. The
coatings and any metals containing these elements can give off toxic fumes
if welded.
BUILDUP OF GAS can injure or kill.
Shut off shielding gas supply when not in use.
Always ventilate confined spaces or use approved
air-supplied respirator.
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense visible
and invisible (ultraviolet and infrared) rays that can burn eyes
and skin. Sparks fly off from the weld.
Wear a welding helmet fitted with a proper shade of filter to protect your face
and eyes from arc rays and sparks when welding or watching (see ANSI
Z49.1 and Z87.1 listed in Safety Standards).
Wear approved safety glasses with side shields under your helmet.
Use protective screens or barriers to protect others from flash and glare;
warn others not to watch the arc.
Wear protective clothing made from durable, flame-resistant material (wool
and leather) and foot protection.
OM-4420 Page 1
WELDING can cause fire or explosion.
HOT PARTS can cause severe burns.
Welding on closed containers, such as tanks, drums, or
pipes, can cause them to blow up. Sparks can fly off from the
welding arc. The flying sparks, hot workpiece, and hot
equipment can cause fires and burns. Accidental contact of electrode to metal
objects can cause sparks, explosion, overheating, or fire. Check and be sure
the area is safe before doing any welding.
Protect yourself and others from flying sparks and hot metal.
Do not weld where flying sparks can strike flammable material.
Remove all flammables within 35 ft (10.7 m) of the welding arc. If this is not
possible, tightly cover them with approved covers.
Be alert that welding sparks and hot materials from welding can easily go
through small cracks and openings to adjacent areas.
Watch for fire, and keep a fire extinguisher nearby.
Be aware that welding on a ceiling, floor, bulkhead, or partition can cause
fire on the hidden side.
Do not weld on closed containers such as tanks, drums, or pipes, unless
they are properly prepared according to AWS F4.1 (see Safety Standards).
Connect work cable to the work as close to the welding area as practical to
prevent welding current from traveling long, possibly unknown paths and
causing electric shock and fire hazards.
Do not use welder to thaw frozen pipes.
Remove stick electrode from holder or cut off welding wire at contact tip
when not in use.
Wear oil-free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes, and a cap.
Remove any combustibles, such as a butane lighter or matches, from your
person before doing any welding.
Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B for hot
work and have a fire watcher and extinguisher nearby.
FLYING METAL can injure eyes.
Welding, chipping, wire brushing, and grinding cause
sparks and flying metal. As welds cool, they can
throw off slag.
Wear approved safety glasses with side shields even
under your welding helmet.
Allow cooling period before maintaining.
Wear protective gloves and clothing when working on
a hot engine.
Do not touch hot engine parts or just-welded parts
bare-handed.
NOISE can damage hearing.
Noise from some processes or equipment can damage
hearing.
Wear approved ear protection if noise level is high.
MAGNETIC FIELDS can affect pacemakers.
Pacemaker wearers keep away.
Wearers should consult their doctor before going
near arc welding, gouging, or spot welding operations.
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under high pressure. If
damaged, a cylinder can explode. Since gas cylinders are
normally part of the welding process, be sure to treat them
carefully.
Protect compressed gas cylinders from excessive heat, mechanical
shocks, slag, open flames, sparks, and arcs.
Install cylinders in an upright position by securing to a stationary support or
cylinder rack to prevent falling or tipping.
Keep cylinders away from any welding or other electrical circuits.
Never drape a welding torch over a gas cylinder.
Never allow a welding electrode to touch any cylinder.
Never weld on a pressurized cylinder — explosion will result.
Use only correct shielding gas cylinders, regulators, hoses, and fittings designed for the specific application; maintain them and associated parts in
good condition.
Turn face away from valve outlet when opening cylinder valve.
Keep protective cap in place over valve except when cylinder is in use or
connected for use.
Read and follow instructions on compressed gas cylinders, associated
equipment, and CGA publication P-1 listed in Safety Standards.
1-3. Engine Hazards
MOVING PARTS can cause injury.
BATTERY EXPLOSION can BLIND.
Always wear a face shield, rubber gloves, and protective clothing when working on a battery.
Stop engine before disconnecting or connecting battery cables or servicing battery.
Do not allow tools to cause sparks when working on a battery.
Do not use welder to charge batteries or jump start vehicles.
Observe correct polarity (+ and −) on batteries.
Disconnect negative (−) cable first and connect it last.
FUEL can cause fire or explosion.
Stop engine and let it cool off before checking or adding fuel.
Do not add fuel while smoking or if unit is near any
sparks or open flames.
Do not overfill tank — allow room for fuel to expand.
Do not spill fuel. If fuel is spilled, clean up before starting engine.
Dispose of rags in a fireproof container.
Always keep nozzle in contact with tank when fueling.
OM-4420 Page 2
Keep away from fans, belts, and rotors.
Keep all doors, panels, covers, and guards closed
and securely in place.
Stop engine before installing or connecting unit.
Have only qualified people remove guards or covers for maintenance
and troubleshooting as necessary.
To prevent accidental starting during servicing, disconnect negative (−)
battery cable from battery.
Keep hands, hair, loose clothing, and tools away from moving parts.
Reinstall panels or guards and close doors when servicing is finished
and before starting engine.
Before working on generator, remove spark plugs or injectors to keep
engine from kicking back or starting.
Block flywheel so that it will not turn while working on generator components.
STEAM AND HOT COOLANT can burn.
If possible, check coolant level when engine is cold to
avoid scalding.
Always check coolant level at overflow tank, if present on unit, instead of radiator (unless told otherwise
in maintenance section or engine manual).
If the engine is warm, checking is needed, and there is no overflow tank,
follow the next two statements.
Wear safety glasses and gloves and put a rag over radiator cap.
Turn cap slightly and let pressure escape slowly before completely removing cap.
ENGINE EXHAUST GASES can kill.
Use equipment outside in open, well-ventilated areas.
If used in a closed area, vent engine exhaust outside
and away from any building air intakes.
BATTERY ACID can BURN SKIN and EYES.
Do not tip battery.
Replace damaged battery.
Flush eyes and skin immediately with water.
ENGINE HEAT can cause fire.
Do not locate unit on, over, or near combustible
surfaces or flammables.
Keep exhaust and exhaust pipes way from flammables.
EXHAUST SPARKS can cause fire.
Do not let engine exhaust sparks cause fire.
Use approved engine exhaust spark arrestor in required areas — see applicable codes.
1-4. Compressed Air Hazards
BREATHING COMPRESSED AIR can
cause serious injury or death.
Do not use compressed air for breathing.
Use only for cutting, gouging, and tools.
COMPRESSED AIR can cause injury.
Wear approved safety goggles.
Do not direct air stream toward self or others.
TRAPPED AIR PRESSURE AND WHIPPING
HOSES can cause injury.
Release air pressure from tools and system before
servicing, adding or changing attachments, or opening compressor oil drain or oil fill cap.
HOT METAL from air arc cutting and
gouging can cause fire or explosion.
Do not cut or gouge near flammables.
Watch for fire; keep extinguisher nearby.
HOT PARTS can cause burns and injury.
Do not touch hot compressor or air system parts.
Let system cool down before touching or servicing.
READ INSTRUCTIONS.
Read Owner’s Manual before using or servicing unit.
Stop engine and release air pressure before
servicing.
1-5. Additional Symbols For Installation, Operation, And Maintenance
FALLING UNIT can cause injury.
Use lifting eye to lift unit only, NOT running gear, gas
cylinders, trailer, or any other accessories.
Use equipment of adequate capacity to lift and
support unit.
If using lift forks to move unit, be sure forks are long
enough to extend beyond opposite side of unit.
OVERHEATING can damage motors.
Turn off or unplug equipment before starting or stopping engine.
Do not let low voltage and frequency caused by low
engine speed damage electric motors.
Wear a face shield to protect eyes and face.
Shape tungsten electrode only on grinder with proper
guards in a safe location wearing proper face, hand,
and body protection.
Allow cooling period; follow rated duty cycle.
Reduce current or reduce duty cycle before starting
to weld again.
Do not block or filter airflow to unit.
STATIC (ESD) can damage PC boards.
Do not connect 50 or 60 Hertz motors to the 100 Hertz receptacle where
applicable.
FLYING SPARKS can cause injury.
OVERUSE can cause OVERHEATING.
Put on grounded wrist strap BEFORE handling
boards or parts.
Use proper static-proof bags and boxes to store,
move, or ship PC boards.
TILTING OF TRAILER can cause injury.
Use tongue jack or blocks to support weight.
Properly install welding generator onto trailer according to instructions supplied with trailer.
Sparks can cause fires — keep flammables away.
OM-4420 Page 3
READ INSTRUCTIONS.
Use only genuine MILLER/Hobart replacement
parts.
Perform engine and air compressor (if applicable)
maintenance and service according to this manual
and the engine/air compressor (if applicable) manuals.
H.F. RADIATION can cause interference.
ARC WELDING can cause interference.
High-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.
Have only qualified persons familiar with electronic
equipment perform this installation.
The user is responsible for having a qualified electrician
promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the equipment at
once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep spark
gaps at correct setting, and use grounding and shielding to minimize the
possibility of interference.
Electromagnetic energy can interfere with sensitive
electronic equipment such as microprocessors,
computers, and computer-driven equipment such as
robots.
Be sure all equipment in the welding area is electromagnetically compatible.
To reduce possible interference, keep weld cables as short as possible,
close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic
equipment.
Be sure this welding machine is installed and grounded according to this
manual.
If interference still occurs, the user must take extra measures such as
moving the welding machine, using shielded cables, using line filters, or
shielding the work area.
1-6. California Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases which
contain chemicals known to the State of California to cause
birth defects and, in some cases, cancer. (California Health &
Safety Code Section 25249.5 et seq.)
For Gasoline Engines:
Engine exhaust contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive
harm.
Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of
California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
For Diesel Engines:
Diesel engine exhaust and some of its constituents are known
to the State of California to cause cancer, birth defects, and
other reproductive harm.
1-7. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126
(phone: 305-443-9353, website: www.aws.org).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard
AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126 (phone: 305-443-9353, website: www.aws.org).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA
02269-9101 (phone: 617-770-3000, website: www.nfpa.org and www.
sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 1735 Jefferson Davis Highway,
Suite 1004, Arlington, VA 22202-4102 (phone: 703-412-0900, website:
www.cganet.com).
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 178 Rexdale Bou-
levard, Rexdale, Ontario, Canada M9W 1R3 (phone: 800-463-6727 or
in Toronto 416-747-4044, website: www.csa-international.org).
Practice For Occupational And Educational Eye And Face Protection,
ANSI Standard Z87.1, from American National Standards Institute, 11
West 42nd Street, New York, NY 10036–8002 (phone: 212-642-4900,
website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269-9101 (phone:
617-770-3000, website: www.nfpa.org and www. sparky.org).
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (there
are 10 Regional Offices—phone for Region 5, Chicago, is
312-353-2220, website: www.osha.gov).
1-8. EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
Welding current, as it flows through welding cables, will cause electromagnetic fields. There has been and still is some concern about such
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National
Research Council concluded that: “The body of evidence, in the
committee’s judgment, has not demonstrated that exposure to powerfrequency electric and magnetic fields is a human-health hazard.”
However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you
may wish to minimize your exposure to electromagnetic fields when
welding or cutting.
OM-4420 Page 4
To reduce magnetic fields in the workplace, use the following
procedures:
1. Keep cables close together by twisting or taping them.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cables around your body.
4. Keep welding power source and cables as far away from
operator as practical.
5. Connect work clamp to workpiece as close to the weld as
possible.
About Pacemakers:
Pacemaker wearers consult your doctor first. If cleared by your doctor,
then following the above procedures is recommended.
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT
UTILISATION
rom_fre 8/03
Avertissement: Protégez vous et les autres des blessures − lisez et suivez ces précautions.
2-1. Signification des symboles
Signifie Mise en garde ! Soyez vigilant ! Cette procédure
présente des risques de danger ! Ceux-ci sont identifiés par
des symboles adjacents aux directives.
Identifie un message de sécurité particulier.
Signifie NOTA ; n’est pas relatif à la sécurité.
Ce groupe de symboles signifie Mise en garde !
Soyez vigilant ! Il y a des
risques de danger reliés
aux CHOCS ÉLECTRIQUES, aux PIÈCES EN MOUVEMENT et aux
PIÈCES CHAUDES. Reportez-vous aux symboles et aux directives ci-dessous afin de connaître les mesures à prendre pour éviter tout danger.
2-2. Dangers relatifs au soudage à l’arc
Les symboles présentés ci-après sont utilisés tout au long du
présent manuel pour attirer votre attention et identifier les risques de danger. Lorsque vous voyez un symbole, soyez
vigilant et suivez les directives mentionnées afin d’éviter tout
danger. Les consignes de sécurité présentées ci-après ne font
que résumer l’information contenue dans les normes de sécurité énumérées à la section 2-6 . Veuillez lire et respecter toutes
ces normes de sécurité.
L’installation, l’utilisation, l’entretien et les réparations ne
doivent être confiés qu’à des personnes qualifiées.
Au cours de l’utilisation, tenir toute personne à l’écart et plus
particulièrement les enfants.
En effectuant les raccordements d’entrée fixer d’abord le conducteur de
mise à la terre approprié et contre-vérifier les connexions.
Vérifier fréquemment le cordon d’alimentation pour voir s’il n’est pas endommagé ou dénudé − remplacer le cordon immédiatement s’il est
endommagé − un câble dénudé peut provoquer une électrocution.
Mettre l’appareil hors tension quand on ne l’utilise pas.
Ne pas utiliser des câbles usés, endommagés, de grosseur insuffisante ou
mal épissés.
Ne pas enrouler les câbles autour du corps.
Si la pièce soudée doit être mise à la terre, le faire directement avec un
câble distinct − ne pas utiliser le connecteur de pièce ou le câble de retour.
Ne pas toucher l’électrode quand on est en contact avec la pièce, la terre ou
une électrode provenant d’une autre machine.
N’utiliser qu’un matériel en bon état. Réparer ou remplacer sur-le-champ
les pièces endommagées. Entretenir l’appareil conformément à ce
manuel.
Porter un harnais de sécurité quand on travaille en hauteur.
Maintenir solidement en place tous les panneaux et capots.
Fixer le câble de retour de façon à obtenir un bon contact métal-métal avec
la pièce à souder ou la table de travail, le plus près possible de la soudure.
Isoler la pince de masse quand pas mis à la pièce pour éviter le contact
avec tout objet métallique.
UN CHOC ÉLECTRIQUE peut tuer.
Un simple contact avec des pièces électriques peut
provoquer une électrocution ou des blessures graves.
L’électrode et le circuit de soudage sont sous tension dès
que l’appareil est sur ON. Le circuit d’entrée et les circuits
internes de l’appareil sont également sous tension à ce
moment-là. En soudage semi-automatique ou automatique, le fil, le dévidoir, le
logement des galets d’entraînement et les pièces métalliques en contact avec
le fil de soudage sont sous tension. Des matériels mal installés ou mal mis à la
terre présentent un danger.
Une tension DC importante subsiste à l’intérieur
des onduleurs après avoir coupé l’alimentation.
Couper l’alimentation du poste et décharger les condensateurs d’entrée
comme indiqué dans la Section Maintenance avant de toucher des composants.
Ne jamais toucher les pièces électriques sous tension.
Porter des gants et des vêtements de protection secs ne comportant pas
de trous.
S’isoler de la pièce et de la terre au moyen de tapis ou d’autres moyens isolants suffisamment grands pour empêcher le contact physique éventuel
avec la pièce ou la terre.
LES FUMÉES ET LES GAZ peuvent
être dangereux.
Ne pas se servir de source électrique àcourant électrique dans les zones
humides, dans les endroits confinés ou là où on risque de tomber.
Le soudage génère des fumées et des gaz. Leur inhalation
peut être dangereux pour votre santé.
Se servir d’une source électrique àcourant électrique UNIQUEMENT si le
procédé de soudage le demande.
Eloigner votre tête des fumées. Ne pas respirer les fumées.
Si l’utilisation d’une source électrique àcourant électrique s’avère nécessaire, se servir de la fonction de télécommande si l’appareil en est équipé.
À l’interieur, ventiler la zone et/ou utiliser un échappement au niveau de
l’arc pour l’évacuation des fumées et des gaz de soudage.
Des précautions de sécurité supplémentaires sont requises dans des envi-
Si la ventilation est insuffisante, utiliser un respirateur à alimentation d’air
homologué.
Lire les spécifications de sécurité des matériaux (MSDSs) et les instructions du fabricant concernant les métaux, les consommables, les
revêtements, les nettoyants et les dégraisseurs.
Travailler dans un espace fermé seulement s’il est bien ventilé ou en portant un respirateur à alimentation d’air. Demander toujours à un surveillant
dûment formé de se tenir à proximité. Des fumées et des gaz de soudage
peuvent déplacer l’air et abaisser le niveau d’oxygène provoquant des
blessures ou des accidents mortels. S’assurer que l’air de respiration ne
présente aucun danger.
Ne pas souder dans des endroits situés à proximité d’opérations de dégraissage, de nettoyage ou de pulvérisation. La chaleur et les rayons de
l’arc peuvent réagir en présence de vapeurs et former des gaz hautement
toxiques et irritants.
Ne pas souder des métaux munis d’un revêtement, tels que l’acier galvanisé, plaqué en plomb ou au cadmium à moins que le revêtement n’ait été
enlevé dans la zone de soudure, que l’endroit soit bien ventilé, et si nécessaire, en portant un respirateur à alimentation d’air. Les revêtements et
tous les métaux renfermant ces éléments peuvent dégager des fumées
toxiques en cas de soudage.
ronnements à risque comme: les endroits humides ou lorsque l’on porte
des vêtements mouillés; sur des structures métalliques au sol, grillages et
échafaudages; dans des positions assises, à genoux et allongées; ou
quand il y a un risque important de contact accidentel avec la pièce ou le
sol. Dans ces cas utiliser les appareils suivants dans l’ordre de préférence:
1) un poste à souder DC semi−automatique de type CV (MIG/MAG), 2) un
poste à souder manuel (électrode enrobée) DC, 3) un poste à souder manuel AC avec tension à vide réduite. Dans la plupart des cas, un poste
courant continu de type CV est recommandé. Et, ne pas travailler seul!
Couper l’alimentation ou arrêter le moteur avant de procéder à l’installation,
à la réparation ou à l’entretien de l’appareil. Déverrouiller l’alimentation
selon la norme OSHA 29 CFR 1910.147 (voir normes de sécurité).
Installer et mettre à la terre correctement cet appareil conformément à son
manuel d’utilisation et aux codes nationaux, provinciaux et municipaux.
Toujours vérifier la terre du cordon d’alimentation − Vérifier et s’assurer que
le fil de terre du cordon d’alimentation est bien raccordé à la borne de terre
du sectionneur ou que la fiche du cordon est raccordée à une prise
correctement mise à la terre.
OM-4420 Page 5
LES ACCUMULATIONS DE GAZ risquent de provoquer des blessures ou
même la mort.
Fermer l’alimentation du gaz protecteur en cas de
non utilisation.
Veiller toujours à bien aérer les espaces confinés ou se servir d’un respirateur d’adduction d’air homologué.
Suivre les recommandations dans OSHA 1910.252(a)(2)(iv) et NFPA 51B
pour les travaux à chaud et avoir de la surveillance et un extincteur à proximité.
DES PARTICULES VOLANTES
peuvent blesser les yeux.
LES RAYONS DE L’ARC peuvent provoquer des brûlures dans les yeux et
sur la peau.
Le soudage, l’écaillement, le passage de la pièce
à la brosse en fil de fer, et le meulage génèrent
des étincelles et des particules métalliques volantes. Pendant la période de refroidissement des soudures, elles risquent de projeter du laitier.
DES PIÈCES CHAUDES peuvent
provoquer des brûlures graves.
Le rayonnement de l’arc du procédé de soudage génère
des rayons visibles et invisibles intenses (ultraviolets et
infrarouges) susceptibles de provoquer des brûlures dans les yeux et sur la
peau. Des étincelles sont projetées pendant le soudage.
Porter un casque de soudage muni d’un écran de filtre approprié pour protéger votre visage et vos yeux pendant le soudage ou pour regarder (voir
ANSI Z49.1 et Z87.1 énuméré dans les normes de sécurité).
Porter des protections approuvés pour les oreilles si le niveau sondre est
trop élevé.
Utiliser des écrans ou des barrières pour protéger des tiers de l’éclair et de
l’éblouissement; demander aux autres personnes de ne pas regarder l’arc.
Porter des vêtements de protection constitué dans une matière durable, résistant au feu (laine ou cuir) et une protection des pieds.
Porter des lunettes de sécurité avec écrans latéraux ou un écran facial.
Prévoir une période de refroidissement avant d’effectuer des travaux d’entretien.
Porter des gants et des vêtements de protection pour
travailler sur un moteur chaud.
Ne pas toucher à mains nues les parties chaudes du moteur ni les pièces
récemment soudées.
LE BRUIT peut affecter l’ouïe.
Le bruit des processus et des équipements peut affecter
l’ouïe.
LE SOUDAGE peut provoquer un incendie ou une explosion.
Porter des protections approuvés pour les oreilles si
le niveau sondre est trop élevé.
Le soudage effectué sur des conteneurs fermés tels que
des réservoirs, tambours ou des conduites peut provoquer
leur éclatement. Des étincelles peuvent être projetées de
l’arc de soudure. La projection d’étincelles, des pièces chaudes et des
équipements chauds peut provoquer des incendies et des brûlures. Le contact
accidentel de l’électrode avec des objets métalliques peut provoquer des
étincelles, une explosion, un surchauffement ou un incendie. Avant de
commencer le soudage, vérifier et s’assurer que l’endroit ne présente pas de
danger.
LES CHAMPS MAGNÉTIQUES peuvent
affecter les stimulateurs cardiaques.
Se protéger et d’autres personnes de la projection d’étincelles et de métal
chaud.
Ne pas souder dans un endroit là où des étincelles peuvent tomber sur des
substances inflammables.
Si des BOUTEILLES sont endommagées, elles pourront exploser.
Déplacer toutes les substances inflammables à une distance de 10,7 m de
l’arc de soudage. En cas d’impossibilité les recouvrir soigneusement avec
des protections homologués.
Des étincelles et des matériaux chauds du soudage peuvent facilement
passer dans d’autres zones en traversant de petites fissures et des
ouvertures.
Des bouteilles de gaz protecteur contiennent du gaz sous
haute pression. Si une bouteille est endommagée, elle peut
exploser. Du fait que les bouteilles de gaz font normalement partie du procédé de soudage, les manipuler avec
précaution.
Surveiller tout déclenchement d’incendie et tenir un extincteur à proximité.
Le soudage effectué sur un plafond, plancher, paroi ou séparation peut déclencher un incendie de l’autre côté.
Ne pas effectuer le soudage sur des conteneurs fermés tels que des réservoirs, tambours, ou conduites, à moins qu’ils n’aient été préparés
correctement conformément à AWS F4.1 (voir les normes de sécurité).
Brancher le câble sur la pièce le plus près possible de la zone de soudage
pour éviter le transport du courant sur une longue distance par des chemins inconnus éventuels en provoquant des risques d’électrocution et
d’incendie.
Ne pas utiliser le poste de soudage pour dégeler des conduites gelées.
En cas de non utilisation, enlever la baguette d’électrode du porte-électrode ou couper le fil à la pointe de contact.
Porter des vêtements de protection dépourvus d’huile tels que des gants
en cuir, une chemise en matériau lourd, des pantalons sans revers, des
chaussures hautes et un couvre chef.
Avant de souder, retirer toute substance combustible de vos poches telles
qu’un allumeur au butane ou des allumettes.
Porteurs de stimulateur cardiaque, restez à distance.
Les porteurs d’un stimulateur cardiaque doivent
d’abord consulter leur médecin avant de s’approcher
des opérations de soudage à l’arc, de gougeage ou
de soudage par points.
Protéger les bouteilles de gaz comprimé d’une chaleur excessive, des
chocs mécaniques, du laitier, des flammes ouvertes, des étincelles et des
arcs.
Placer les bouteilles debout en les fixant dans un support stationnaire ou
dans un porte-bouteilles pour les empêcher de tomber ou de se renverser.
Tenir les bouteilles éloignées des circuits de soudage ou autres circuits
électriques.
Ne jamais placer une torche de soudage sur une bouteille à gaz.
Une électrode de soudage ne doit jamais entrer en contact avec une bouteille.
Ne jamais souder une bouteille pressurisée − risque d’explosion.
Utiliser seulement des bouteilles de gaz protecteur, régulateurs, tuyaux et
raccords convenables pour cette application spécifique; les maintenir ainsi
que les éléments associés en bon état.
Ne pas tenir la tête en face de la sortie en ouvrant la soupape de la bouteille.
Maintenir le chapeau de protection sur la soupape, sauf en cas d’utilisation
ou de branchement de la bouteille.
Lire et suivre les instructions concernant les bouteilles de gaz comprimé,
les équipements associés et les publication P-1 CGA énumérées dans les
normes de sécurité.
2-3. Dangers existant en relation avec le moteur
LES ACCUMULATIONS DE GAZ risquent de provoquer des blessures ou
même la mort.
Fermer l’alimentation du gaz protecteur en cas de
non utilisation.
Veiller toujours à bien aérer les espaces confinés ou se servir d’un respirateur d’adduction d’air homologué.
OM-4420 Page 6
L’ACIDE DE LA BATTERIE peut provoquer des brûlures dans les YEUX et
sur la PEAU.
Ne pas renverser la batterie.
Remplacer une batterie endommagée.
Rincer immédiatement les yeux et la peau à l’eau.
L’EXPLOSION DE LA BATTERIE peut
RENDRE AVEUGLE.
Toujours porter une protection faciale, des gants en
caoutchouc et vêtements de protection lors d’une intervention sur la batterie.
Arrêter le moteur avant de débrancher ou de brancher les câbles de
batterie.
Eviter de provoquer des étincelles avec les outils en travaillant sur la
batterie.
Ne pas utiliser le poste de soudage pour charger les batteries ou des véhicules de démarrage rapide.
Observer la polarité correcte (+ et −) sur les batteries.
Débrancher le câble négatif (–) en premier lieu. Le rebrancher en dernier
lieu.
LE CARBURANT MOTEUR peut provoquer un incendie ou une explosion.
Arrêter le moteur avant de vérifier le niveau de carburant ou de faire le plein.
Ne pas faire le plein en fumant ou proche d’une source d’étincelles ou d’une flamme nue.
Ne pas faire le plein de carburant à ras bord; prévoir de l’espace pour son
expansion.
Faire attention de ne pas renverser de carburant. Nettoyer tout carburant renversé avant de faire démarrer le moteur.
Jeter les chiffons dans un récipient ignifuge.
LA VAPEUR ET LE LIQUIDE DE
REFROIDISSEMENT CHAUD peuvent
provoquer des brûlures.
Il est préférable de vérifier le liquide de
refroidissement une fois le moteur refroidi pour éviter
de se brûler.
Toujours vérifier le niveau de liquide de refroidissement dans le vase d’expansion (si présent), et non dans le radiateur (sauf si précisé autrement
dans la section maintenance du manuel du moteur).
Si le moteur est chaud et que le liquide doit être vérifié, opérer comme suivant :
Mettre des lunettes de sécurité et des gants, placer un torchon sur le bouchon du radiateur.
Dévisser le bouchon légèrement et laisser la vapeur s’échapper avant
d’enlever le bouchon.
LA CHALEUR DU MOTEUR peut provoquer un incendie.
DES ORGANES MOBILES peuvent
provoquer des blessures.
Pour empêcher tout démarrage accidentel pendant les travaux d’entretien,
débrancher le câble négatif (−) de batterie de la borne.
Ne pas approcher les mains, cheveux, vêtements lâches et outils des organes mobiles.
Remettre en place les panneaux ou les dipositifs de protection et fermer les
portes à la fin des travaux d’entretien et avant de faire démarrer le moteur.
Avant d’intervenir, déposer les bougies ou injecteurs pour éviter la mise en
route accidentelle du moteur.
Bloquer le volant moteur pour éviter sa rotation lors d’une intervention sur le
générateur.
Ne pas approcher les mains des ventilateurs, courroies et autres pièces en mouvement.
Maintenir fermés et fixement en place les portes,
panneaux, recouvrements et dispositifs de
protection.
Ne pas placer l’appareil sur, au-dessus ou à proximité
de surfaces inflammables.
Tenir à distance les produits inflammables de
l’échappement.
LES ÉTINCELLES À L’ÉCHAPPEMENT
peuvent provoquer un incendie.
Arrêter le moteur avant d’installer ou brancher l’appareil.
Demander seulement à un personnel qualifié d’enlever les dispositifs de
sécurité ou les recouvrements pour effectuer, s’il y a lieu, des travaux d’entretien et de dépannage.
Empêcher les étincelles d’échappement du moteur
de provoquer un incendie.
Utiliser uniquement un pare-étincelles approuvé −
voir codes en vigueur.
2-4. Dangers liés à l’air comprimé
RESPIRER L’AIR COMPRIMÉ peut provoquer des blessures graves ou causer
la mort.
Le METAL CHAUD lors du coupage et
gougeage plasma peut provoquer un incendie ou une explosion.
Ne pas utiliser l’air comprimé pour respirer.
Utiliser l’air comprimé seulement pour le coupage, gougeage et les outils pneumatiques.
Ne pas couper ou gouger à proximité de produits
inflammables.
Surveillez et garder un extincteur à proximité.
L’AIR COMPRIMÉ peut provoquer
des blessures.
DES PIECES CHAUDES peuvent provoquer des brûlures et blessures.
Porter des lunettes de sécurité approuvées.
Ne pas diriger le jet d’air vers d’autres ou soi−
même.
Ne pas toucher le compresseur ou d’autres éléments du circuit air comprimé chauds.
Laisser l’ensemble se refroidir avant de toucher
ou d’effectuer la maintenance.
L’AIR COMPRIME EMMAGASINE ET DES
TUYAUX SOUS PRESSION peuvent provoquer des blessures.
LIRE LES INSTRUCTIONS.
Relâcher la pression d’air de l’outillage ou du système avant d’effectuer la maintenance, avant de
changer ou de rajouter des éléments ou avant
d’ouvrir la purge ou le bouchon de remplissage
d’huile.
Lisez le manuel d’instructions avant l’utilisation
ou la maintenance de l’appareil.
Arrêter le moteur et relâcher la pression avant
d’effectuer la maintenance.
2-5. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la
maintenance
LA CHUTE DE L’APPAREIL peut
blesser.
Utiliser l’anneau de levage uniquement pour soulever
l’appareil lui-même ; sans chariot, de bouteilles de
gaz, remorque, ou autres accessoires.
Utiliser un équipement de levage de capacité suffisante pour lever
l’appareil.
En utilisant des fourches de levage pour déplacer l’unité, s’assurer
que les fourches sont suffisamment longues pour dépasser du côté
opposé de l’appareil.
OM-4420 Page 7
LE SURCHAUFFEMENT peut endommager le moteur électrique.
LIRE LES INSTRUCTIONS.
Arrêter ou déconnecter l’équipement avant de démarrer ou d’arrêter le moteur.
Ne pas laisser tourner le moteur trop lentement sous
risque d’endommager le moteur électrique à cause
d’une tension et d’une fréquence trop faibles.
Ne pas brancher de moteur de 50 ou de 60 Hz à la prise de 100 Hz, s’il y a
lieu.
LE RAYONNEMENT HAUTE FRÉQUENCE (H.F.) risque de provoquer
des interférences.
LES ÉTINCELLES VOLANTES risquent de provoquer des blessures.
L’EMPLOI EXCESSIF peut
SURCHAUFFER L’ÉQUIPEMENT.
Établir la connexion avec la barrette de terre avant de
manipuler des cartes ou des pièces.
Utiliser des pochettes et des boîtes antistatiques
pour stocker, déplacer ou expédier des cartes de
circuits imprimes.
UNE REMORQUE QUI BASCULE peut
entraîner des blessures.
Laisser l’équipement refroidir ; respecter le facteur de
marche nominal.
Réduire le courant ou le facteur de marche avant de
poursuivre le soudage.
Ne pas obstruer les passages d’air du poste.
LES CHARGES ÉLECTROSTATIQUES peuvent endommager les
circuits imprimés.
Le rayonnement haute fréquence (H.F.) peut
provoquer des interférences avec les équipements
de radio−navigation et de communication, les
services de sécurité et les ordinateurs.
Demander seulement à des personnes qualifiées familiarisées avec des
équipements électroniques de faire fonctionner l’installation.
L’utilisateur est tenu de faire corriger rapidement par un électricien qualifié les interférences résultant de l’installation.
Si le FCC signale des interférences, arrêter immédiatement l’appareil.
Effectuer régulièrement le contrôle et l’entretien de l’installation.
Maintenir soigneusement fermés les portes et les panneaux des sources
de haute fréquence, maintenir les éclateurs à une distance correcte et
utiliser une terre et et un blindage pour réduire les interférences
éventuelles.
Porter un écran facial pour protéger le visage et les
yeux.
Affuterr l’électrode au tungstène uniquement à la meuleuse dotée de protecteurs. Cette manoeuvre est à exécuter dans un endroit sûr lorsque
l’on porte l’équipement homologué de protection du visage, des mains et
du corps.
Les étincelles risquent de causer un incendie − éloigner toute substance
inflammable.
Utiliser les supports de la remorque ou des blocs
pour soutenir le poids.
Installer convenablement le poste sur la remorque
comme indiqué dans le manuel s’y rapportant.
Utiliser seulement les pièces de rechange d’origine.
Effectuer la maintenance du moteur et du compresseur (si applicable) suivant ce manuel et le manuel du
moteur/compresseur (si applicable).
LE SOUDAGE À L’ARC risque de
provoquer des interférences.
L’énergie électromagnétique risque de provoquer
des interférences pour l’équipement électronique
sensible tel que les ordinateurs et l’équipement commandé par ordinateur tel que les robots.
Veiller à ce que tout l’équipement de la zone de soudage soit compatible
électromagnétiquement.
Pour réduire la possibilité d’interférence, maintenir les câbles de soudage aussi courts que possible, les grouper, et les poser aussi bas que possible (ex. par terre).
Veiller à souder à une distance de 100 mètres de tout équipement électronique sensible.
Veiller à ce que ce poste de soudage soit posé et mis à la terre conformément à ce mode d’emploi.
En cas d’interférences après avoir pris les mesures précédentes, il incombe à l’utilisateur de prendre des mesures supplémentaires telles que
le déplacement du poste, l’utilisation de câbles blindés, l’utilisation de filtres de ligne ou la pose de protecteurs dans la zone de travail.
2-6. Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, norme ANSI Z49.1, de
l’American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126 (téléphone : (305) 443−9353, site Web : www.aws.org).
Recommended Safe Practices for the Preparation for Welding and Cutting
of Containers and Piping, norme American Welding Society AWS F4.1, de
l’American Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126 (téléphone : (305) 443−9353, site Web : www.aws.org).
National Electrical Code, norme NFPA 70, de la National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101
(téléphone : (617) 770−3000, sites Web : www.nfpa.org et www.sparky.org).
Safe Handling of Compressed Gases in Cylinders, brochure CGA P−1, de
la Compressed Gas Association, 1735 Jefferson Davis Highway, Suite
1004, Arlington, VA 22202−4102 (téléphone : (703) 412−0900, site Web :
www.cganet.com).
Code for Safety in Welding and Cutting, norme CSA W117.2, de la Canadian Standards Association, Standards Sales, 178 boulevard Rexdale,
Rexdale (Ontario) Canada M9W 1R3 (téléphone : (800) 463−6727 ou à Toronto : (416) 747−4044, site Web : www.csa−international.org).
Practice For Occupational And Educational Eye And Face Protection,
norme ANSI Z87.1, de l’American National Standards Institute, 11 West
42nd Street, New York, NY 10036−8002 (téléphone : (212) 642−4900, site
Web : www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot Work,
norme NFPA 51B, de la National Fire Protection Association, P.O. Box
9101, 1 Battery March Park, Quincy, MA 02269−9101 (téléphone : (617)
770−3000, site Web : www.nfpa.org et www.sparky.org).
OSHA, Occupational Safety and Health Standards for General Industry,
Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and
Part 1926, Subpart J, de l’U.S. Government Printing Office, Superintendent
of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (il y a 10 bureaux
régionaux − Téléphone pour la Région 5, Chicago : (312) 353−2220, site
Web : www.osha.gov).
2-7. Information sur les champs électromagnétiques
Données sur le soudage électrique et les effets des champs magnétiques
basse fréquence sur l’organisme
En parcourant les câbles de soudage, le courant crée des champs électromagnétiques. Les effets potentiels de tels champs restent préoccupants.
Cependant, après avoir examiné plus de 500 études qui ont été faites pendant une période de recherche de 17 ans, un comité de spécialistes du
National Research Council a conclu : « L’accumulation de preuves n’a pas
démontré que l’exposition aux champs magnétiques et aux champs électriques à haute fréquence constitue un risque pour la santé humaine ».
Toutefois, les études et l’examen des preuves se poursuivent. En attendant
les conclusions finales de la recherche, il serait souhaitable de réduire l’exposition aux champs électromagnétiques pendant le soudage ou le
coupage.
OM-4420 Page 8
Afin de réduire les champs électromagnétiques en milieu de travail, respecter les consignes suivantes :
1. Garder les câbles ensemble en les torsadant ou en les fixant avec du
ruban adhésif.
2. Mettre tous les câbles du côté opposé à l’opérateur.
3. Ne pas s’enrouler les câbles autour du corps.
4. Garder le poste de soudage et les câbles le plus loin possible de soi.
5. Placer la pince de masse le plus près possible de la zone de soudage.
Consignes relatives aux stimulateurs cardiaques :
Les personnes qui portent un stimulateur cardiaque doivent avant tout
consulter leur médecin. Si ce dernier les déclare aptes, il leur est recommandé de respecter les consignes ci-dessus.
SECTION 3 − DEFINITIONS
3-1. Symbols And Definitions
A
3
Stop Engine
Fast (Run, Weld/
Power)
Slow (Idle)
Start Engine
Check engine belt
Check Air Cleaner
Starting Aid
Engine
Battery (Engine)
Hourmeter (HM)
Temperature
Circuit Breaker
Do Not Switch
Under Load
Read Operator’s
Manual
Certified/Trained
Mechanic
Engine Oil
Check Injectors/
Pump
Check Valve
Clearance
Fuel
Engine Coolant
Temperature
Positive
Negative
Wire Feed
Welding Arc
Volts
Panel/Local
Remote
Output
Direct Current
(DC)
Alternating
Current (AC)
Gas Tungsten Arc
Welding (TIG)
Stick (SMAW)
Welding
Constant Current
(CC)
MIG (GMAW)
Welding
Constant Voltage
(CV)
Single Phase
Air Carbon Arc
Cutting (CAC-A)
Protective Earth
(Ground)
DC Electrode
Positive
DC Electrode
Negative
Work Connection
Electrode
Connection
On
Off
V
Amperes
Three Phase
1
h
Hours
s
Seconds
Time
OM-4420 Page 9
SECTION 4 − SPECIFICATIONS
4-1. Weld, Power, And Engine Specifications
Welding
Mode
CC/DC
CV/DC
Weld
Output
Range
Rated
Welding
Output
Maximum
Open-Circuit
Voltage
(Nominal)
20 − 750 A
600 A,
44 Volts
DC,
100% Duty
Cycle
95
14 − 40 V
Generator Power
Rating
Engine
Standard
Single-Phase,
4 kVA/kW,
kVA/kW 34/17 A
A,
120/240 V AC,
50/60 Hz
600 A,
36 Volts
DC,
100% Duty
Cycle
Engine
Oil
Capacity
Fuel Tank
Capacity
11 qt
q
(10.4
(10
4 L)
25 gal
g
(95 L)
DEUTZ
Deutz BF4M2011
Oil-Cooled,
Four-Cylinder,
Turbo-Charged
64 HP Diesel Engine
56
4-2. Sound Level Table
Idle Speed (1235 rpm)
Weld/Power Speed
(1850 rpm)
40 Volts DC At 500 Amps
44 Volts DC At 600 Amps
94.6 Lwa sound power
100.6 Lwa sound power
103.0 Lwa sound power
104.5 Lwa sound power
69.7 dBa at 23 ft (7 m)
74.5 dBA 3.3 ft (1 m)
from front panel
75.7dBa at 23 ft (7 m)
78.8 dBA 3.3 ft (1 m) from
front panel
78.1 dBa at 23 ft (7 m)
86.0 dBA 3.3 ft (1 m) from
front panel
79.6 dBa at 23 ft (7 m)
91.8 dBA 3.3 ft (1 m) from
front panel
4-3. Dimensions, Weights, And Operating Angles
Dimensions
Height
Width
54-1/2 in (1384 mm)
(to top of muffler)
G
28-1/2 in (724 mm)
(mtg. brackets turned in)
Do not exceed tilt angles or engine could
be damaged or unit could tip.
30-3/4 in (781 mm)
(mtg. brackets turned out)
Depth
69-1/2 in (1765 mm)
A
69-1/2 in (1765 mm)
B*
55-7/8 in (1419 mm)
C*
46-3/8 in (1178)
D*
11 in (279 mm)
E
27-1/2 in (699 mm)
F
1 in (25 mm)
G
29-1/2 in (749 mm)
H
9/16 in (14 mm) Dia.
4 Holes
* With mounting brackets in center
position. Dimensions vary with location of mounting brackets.
Do not move or operate
p
unit where it could
ti
tip.
A
B
C
30°
H
D
20°
30°
20°
Front Panel End
F
E
Weight
No Fuel: 1780 lb (807 kg)
w/Fuel: 1955 lb (997 kg)
OM-4420 Page 10
802 161-A
803 452
4-4. Stick And MIG Volt-Ampere Curves
The volt-ampere curve shows the
minimum and maximum voltage
and amperage output capabilities of
the welding generator. Curves of all
other settings fall between the
curves shown.
A. DC Stick Mode
100
Ranges
300 − Max
185 − 525
125 − 400
85 − 250
55 − 125
DC VOLTS
80
60
40
20
0
0
100
200
300
400 500 600
DC AMPERES
700
800
900
1000
400 500 600
DC AMPERES
700
800
900
1000
B. MIG Mode
100
DC VOLTS
80
60
MAX
40
MIN
20
0
0
100
200
300
208 135 / 203 415
OM-4420 Page 11
4-5. DC TIG Volt-Ampere Curves
The volt-ampere curve shows the
minimum and maximum voltage
and amperage output capabilities of
the welding generator. Curves of all
other settings fall between the
curves shown.
100
Ranges
60−450
40−330
30−220
20−110
DC VOLTS
80
60
40
20
0
0
50 100 150 200 250 300 350 400 450 500 550 600 650 700
DC AMPERES
208 136
4-6. Fuel Consumption
US Gal./Hr.
The curve shows typical fuel use
under weld or generator power
loads.
3.00
2.75
2.50
2.25
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0.00
IDLE
0
50
100 150 200 250 300 350 400 450 500 550 600
DC WELD AMPERES AT 100% DUTY CYCLE
Ref. 208 211
OM-4420 Page 12
4-7. Duty Cycle And Overheating
100% Duty Cycle At 600 Amperes
Duty Cycle is percentage of 10 minutes that unit can weld at rated load
without overheating.
Exceeding duty cycle can
damage unit and void
warranty.
Continuous Welding
1000
800
600
500
WELD AMPERES
400
300
250
200
150
100
10
15
20
25
30
40
50
60
80 100
% DUTY CYCLE
212 060-C
4-8. Generator AC Power Curve
The ac power curve shows the generator power in amperes available
at the 120 and 240 volt receptacles.
150 300
AC VOLTS
125 250
100 200
75
150
50
100
25
50
0
0
0
5
10
15
20
AC AMPERES IN 240V MODE
25
30
0
10
20
30
40
AC AMPERES IN 120V MODE
50
60
193 018
OM-4420 Page 13
4-9. Manufacturing Rating Label
OM-4420 Page 14
SECTION 5 − INSTALLATION
5-1. Installing Welding Generator
Always securely fasten welding generator onto transport
vehicle or trailer and comply
with all DOT and other applicable codes.
Movement
Always ground generator
frame to vehicle frame to prevent electric shock and static
electricity hazards.
OR
If unit does not have GFCI receptacles, use GFCI-protected
extension cord.
OR
See Section 5-2 for mounting information.
Grounding:
1
Location
2
3
OR
Equipment Grounding Terminal
(On Front Panel)
Grounding Cable (Not Supplied)
Metal Vehicle Frame
Connect cable from equipment
ground terminal to metal vehicle
frame. Use #10 AWG or larger insulated copper wire.
OR
Grounding
1
GND/PE
2
Electrically bond generator frame to
vehicle frame by metal-to-metal contact.
3
Bed liners, shipping skids, and some running
gears insulate the welding generator from the
vehicle frame. Always connect a ground wire
from the generator equipment grounding terminal to bare metal on the vehicle frame as shown.
Airflow Clearance
18 in
(460 mm)
18 in
(460 mm)
18 in
(460 mm)
18 in
(460 mm)
18 in
(460 mm)
install3 6/04 − Ref. 800 652 / Ref. 800 477-A / 803 274
OM-4420 Page 15
5-2. Mounting Welding Generator
Do not weld on base. Welding on base can cause fuel
tank fire or explosion. Weld
only on the four mounting
brackets or bolt unit down.
Supporting The Unit
Do not mount unit by supporting the base only at the
four
mounting brackets.
Use cross-supports to adequately support unit and prevent damage to base.
2
Mounting Surface:
1
2
OR
Cross-Supports
Mounting Brackets (Supplied)
Mount unit on flat surface or use
cross-supports to support base.
Secure unit with mounting brackets.
1
3
Inadequate support.
4
1/2 in Bolt And Washer
(Minimum − Not Supplied)
3/8-16 x 1 in Screws
(Supplied)
To Bolt Unit In Place:
Do not use flexible mounts.
Remove hardware securing the
four mounting brackets to the base.
Reverse brackets and reattach to
base with original hardware.
1
Mount unit to truck or trailer with 1/2
in (12 mm) or larger hardware (not
supplied).
Using Mounting Brackets
To Weld Unit In Place:
Weld unit to truck or trailer only at
the four mounting brackets.
2
Welding Unit In Place
Bolting Unit In Place
3
2
4
Tools Needed:
9/16 in
install3 6/04 803 274 / 190 250-A / 803 231
OM-4420 Page 16
5-3. Installing Optional Spark Arrestor Muffler
Stop engine and let cool.
2
Spark Arrestor Muffler
Double-Flanged Elbow
Nut
Flat Washer
Mount
Bracket
Screw
Single-Flanged Elbow
Rain Cap
Clamp
Loosely assemble components as
shown.
1
10
1
2
3
4
5
6
7
8
9
10
Mount the muffler with the clean-
9
out plug to the outside.
After assembly, final-tighten
clamps and hardware.
all
Be
sure to tighten rain cap
mounting screw.
7
6
8
5
4
3
Tools Needed:
7/16, 1/2 in
803 453
OM-4420 Page 17
5-4. Activating The Dry Charge Battery (If Applicable)
Remove battery from unit.
1
5
4
1
2
3
4
5
Eye Protection − Safety
Glasses Or Face Shield
Rubber Gloves
Vent Caps
Sulfuric Acid Electrolyte
(1.265 Specific Gravity)
Well
Fill each cell with electrolyte to
bottom of well (maximum).
3
Do not overfill battery cells.
Wait ten minutes and check electrolyte level. If necessary, add electrolyte to raise to proper level. Reinstall vent caps.
6
Battery Charger
Read and follow all instructions supplied with battery
charger.
2
Charge battery for 12 minutes at 30
amperes or 30 minutes at 5 amperes. Disconnect charging cables
and install battery.
When electrolyte
is low, add
only distilled water to cells to
maintain proper level.
6
5 A For 30 Minutes
Tools Needed:
OR
+
−
rubber gloves
30 A For 12 Minutes
glasses
drybatt1 1/98 − 0886
OM-4420 Page 18
5-5. Connecting The Battery
Reinstall cover after connecting battery.
Connect Negative (−) Cable Last.
+
−
Tools Needed:
1/2 in
802 168-E / Ref. 202 705 / 802 313 / S-0756-C
5-6. Using The Optional Battery Disconnect Switch
Stop engine.
1
1
OFF
ON
Battery Disconnect Switch
The battery disconnect switch disconnects battery voltage from the
circuit. When the switch is turned
Off, the front panel controls do not
work.
To run unit, turn switch to On position. To prevent unit from running,
turn switch to Off position.
The switch may be locked using a
customer-supplied padlock.
803 454 / Ref. 803 324
OM-4420 Page 19
5-7. Engine Prestart Checks
Engine Oil
Full
Diesel
Full
803 454
Check all engine fluids daily.
Engine must be cold and on a level surface.
Unit is shipped with 20W break-in oil. The
automatic shutdown system stops engine if
oil pressure is too low or coolant temperature is too high.
This unit has a low oil pressure shut-
down switch. However, some conditions may cause engine damage before
the engine shuts down. Check oil level
often and do not use the oil pressure
shutdown system to monitor oil level.
Follow run-in procedure in engine manual.
If unburned fuel and oil collect in exhaust
pipe during run-in, see Section 11.
OM-4420 Page 20
Fuel
Do not use gasoline. Gasoline will
damage engine.
Add fresh diesel fuel before starting to prevent air from entering the fuel system (see
engine maintenance label for fuel specifications). Leave filler neck empty to allow room
for expansion.
Engine stops if fuel level is low on units with
low fuel shutdown option. Do not run out of
fuel or air may enter fuel system and cause
starting problems. See engine manual to
bleed air from fuel system.
Engine Oil
After fueling, check oil with unit on level surface. If oil is not up to full mark on dipstick,
add oil (see maintenance label for engine oil
specifications).
Cold Weather Starting
To improve cold weather starting:
Use Starting Aid switch (see Section
6-1).
Keep battery in good condition. Store
battery in warm area.
Use fuel formulated for cold weather
(diesel fuel can gel in cold weather).
Contact local fuel supplier for fuel information.
Use correct grade oil for cold weather
(see Section 8-2).
5-8. Connecting To Weld Output Terminals
Stop engine.
1
Positive (+) Weld Output Terminal
2
Negative (−) Weld Output Terminal
Stick And TIG Welding
For Stick welding Direct Current Electrode
Positive (DCEP), connect electrode holder
cable to Positive (+) terminal on left and work
cable to Negative (−) terminal on right.
For Stick and TIG Direct Current Electrode
Negative (DCEN), connect electrode holder
cable to Negative (−) terminal on right and work
cable to Positive (+) terminal on left.
MIG And FCAW Welding
For MIG welding Direct Current Electrode Positive (DCEP), connect wire feeder cable to
Positive (+) terminal on left and work cable to
Negative (−) terminal on right. Use Process/
Contactor switch to select type of weld output
(see Section 6-3).
For MIG and FCAW Direct Current Electrode
Negative (DCEN), connect wire feeder cable
to Negative (−) terminal on right and work cable
to Positive (+) terminal on left. Use Process/
Contactor switch to select type of weld output
(see Section 6-3).
1
2
Tools Needed:
803 452
3/4 in
Notes
Start Your Professional
Welding Career Now!
400 Trade Square East, Troy, Ohio 45373
1-800-332-9448 www.welding.org
Over 80,000 trained
since 1930!
OM-4420 Page 21
5-9. Selecting Weld Cable Sizes*
Weld Cable Size** and Total Cable (Copper) Length in Weld Circuit
Not Exceeding***
100 ft (30 m) or Less
150 ft
(45 m)
200 ft
(60 m)
250 ft
(70 m)
300 ft
(90 m)
350 ft
400 ft
(105 m) (120 m)
Weld Output
Terminals
Turn off power before
connecting to weld output terminals.
Welding
Amperes
10 − 60%
Duty
Cycle
60 − 100%
Duty
Cycle
100
4 (20)
4 (20)
4 (20)
3 (30)
2 (35)
1 (50)
1/0 (60)
1/0 (60)
150
3 (30)
3 (30)
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
3/0 (95)
200
3 (30)
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
4/0 (120)
250
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 2/0
(2x70)
300
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 3/0
(2x95)
350
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
400
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
2 ea. 4/0
(2x120)
500
2/0 (70)
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 3/0
(3x95)
3 ea. 3/0
(3x95)
600
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 3/0
(3x95)
3 ea. 4/0
(3x120)
3 ea. 4/0
(3x120)
700
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 3/0
(3x95)
3 ea. 4/0
(3x120)
3 ea. 4/0
(3x120)
4 ea. 4/0
(4x120)
800
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 4/0
(3x120)
3 ea. 4/0
(3x120)
4 ea. 4/0
(4x120)
4 ea. 4/0
(4x120)
Do not use worn, damaged, undersized, or
poorly spliced cables.
* Chart
10 − 100% Duty Cycle
is a general guideline and may not suit all applications. If cable overheats, use next size larger cable.
**Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere.
( ) = mm2 for metric use
S-0007-F
***For distances longer than those shown in this guide, call a factory applications representative at 920-735-4505.
Notes
Work like a Pro!
Pros weld and cut
safely. Read the
safety rules at
the beginning
of this manual.
OM-4420 Page 22
5-10. Connecting To Remote 14 Receptacle RC14
Socket*
Socket Information
A
24 volts ac. Protected by circuit
breaker CB5 (see Section 8-7).
B
Contact closure to A completes
24 volt ac contactor control
circuit.
C
Output to remote control:+10
volts dc in MIG or Stick mode;
0 to +10 volts dc in TIG mode.
D
Remote control circuit common.
E
DC input command signal: 0 to
+10 volts from min. to max. of
remote control with Voltage/
Amperage Adjust control at
max.
24 VOLTS AC
REMOTE
OUTPUT
CONTROL
OR
I
115 volts, 10 amperes, 60 Hz
ac. Protected by circuit breaker
CB6 (see Section 8-7).
J
Contact closure to I completes
115 volt ac contactor control
circuit.
K
Chassis common.
G
Circuit common for 24 and 115
volt ac circuit.
115 VOLTS AC
803 452
GND
NEUTRAL
*The remaining sockets are not used.
Notes
OHM’S LAW
VOLTAGE =
CURRENT X RESISTANCE
CURRENT = VOLTAGE
RESISTANCE
RESISTANCE = VOLTAGE
CURRENT
OM-4420 Page 23
SECTION 6 − OPERATING THE WELDING GENERATOR
6-1. Controls (See Section 6-2)
9
10
12
13
6
5
3
4
7
8
11
1
2
803 454 / 217 638-A
OM-4420 Page 24
6-2. Description Of Controls (See Section 6-1)
Engine Starting Controls
scheduling maintenance.
1
4
Starting Aid Switch
Use switch to energize starting aid for cold
weather starting.
Push switch up for 60 seconds to operate the
starting aid (intake air heater) before cranking
engine (see starting instructions following).
2
Engine Control Switch
Use switch to start engine, select engine
speed, and stop engine.
In Run position, engine runs at weld/power
speed. In Run/Idle position, engine runs at
idle speed with no generator power or weld
load, and weld/power speed with load applied.
To Start:
If engine does not start, let engine come
to a complete stop before attempting restart.
Above 32 F (0 C): turn Engine Control
switch to Start. Release Engine Control
switch when engine starts.
Fuel Gauge
Use gauge to check fuel level. Engine stops
if fuel level is low on units with low fuel shutdown option.
To check fuel level when engine is not running, turn Engine Control switch to Run/Idle
position.
5
Engine Oil Pressure Gauge
Normal pressure is 30 − 60 psi (206 − 414
kPa). Engine stops if pressure is below 20 psi
(138 kPa).
6
Engine Temperature Gauge
Normal temperature is 212 - 239° F (100 115° C). Engine stops if temperature exceeds
270° F (132° C).
7
Battery Voltmeter
Use gauge to check battery voltage and monitor the engine charging system. The meter
should read about 14 volts dc when the engine is running, and about 12 volts dc when
the engine is stopped.
Weld output would be about 263 A DC with
controls set as shown (50% of 125 to 400 A).
The numbers around the Voltage/Amper-
age Adjust control are for reference only
and do not represent an actual percentage value.
11 Voltage/Amperage Adjust Switch And
Remote 14 Receptacle
Weld Meters
Use switch to select weld amperage range.
Use gauge to monitor engine running time for
With Process/Contactor switch in any Stick or
TIG setting, use control to adjust amperage
within range selected by Ampere Range
switch. With Process/Contactor switch in any
MIG position, use control to adjust voltage.
With Voltage/Amperage Adjust Switch in Remote position, control limits the remote amperage in TIG mode, but has no effect in Stick
and MIG modes.
9
To Stop: turn Engine Control switch to Off
position.
Engine Hour Meter
10 Voltage/Amperage Adjust Control
See Section 6-3 for Process/Contactor
switch information.
Weld Controls
3
For most welding applications, use lowest
amperage range possible to help prevent arc
outages.
Use switch to select front panel or remote
voltage/amperage control. For remote control, place switch in Remote position and connect remote control to Remote 14 receptacle
RC14 (see Sections 5-10 and 6-4).
Below 32 F (0 C) using starting aid
switch:
Turn Engine Control switch to Run/Idle position. Push Starting Aid switch up for 60 seconds. While still holding Starting Aid switch,
turn Engine Control switch to Start. Release
Engine Control switch and Starting Aid switch
when engine starts.
Engine Gauges
Use the highest range for MIG welding and for
cutting and gouging (CAC-A).
8
Process/Contactor Switch
Ampere Range Switch
Do not switch under load.
Use all five ranges for Stick welding, and the
lowest four ranges for TIG welding. Read the
upper set of numbers at each range for Stick
welding and the lower set at each range for
TIG welding.
12 AC/DC Voltmeter (Optional)
Voltmeter displays voltage at the weld output
terminals, but not necessarily the welding arc
due to resistance of cable and connections.
13 AC/DC Ammeter (Optional)
Ammeter displays amperage output of the
unit.
OM-4420 Page 25
6-3. Process/Contactor Switch
1
Process/Contactor Switch
Weld output terminals are energized when Process/Contactor
switch is in a Weld Terminals Always On position and the engine is running.
1
DC voltage is still present at the
weld terminals when Process/
Contactor switch is in the Remote On/Off Switch Required −
Stick position and the engine is
running.
Use switch to select weld process and
weld output on/off control (see table below and Section 6-4).
Place switch in Remote On/Off Switch
Required positions to turn weld output
on and off with a device connected to
the remote 14 receptacle.
Place switch in Weld Terminals Always
On positions for weld output to be on
whenever the engine is running.
Use Stick position for air carbon arc
(CAC-A) cutting and gouging.
When switch is in a Stick position, the
arc drive (dig) circuit provides additional amperage during low voltage (short
arc length conditions) to prevent “sticking” electrodes.
The arc drive (dig) circuit is disabled
when switch is in MIG or TIG positions.
The engine auto idle option does
not work in the Remote On/Off
Switch Required-TIG mode.
217 638-A
Process/Contactor Switch Settings
Switch Setting
Process
Output On/Off Control
Engine Auto Idle (Optional)
Remote On/Off Switch Required − TIG, HF Required
Or Scratch Start TIG
GTAW With HF Unit, Pulsing
Device, Or Remote Control
At Remote 14 Receptacle
Not Active
Remote On/Off Switch
Required − Stick
Stick (SMAW) With Remote On/Off
At Remote 14 Receptacle
Active
Remote On/Off Switch
Required − CV Feeder
Using Remote
MIG (GMAW)
At Remote 14 Receptacle
Active
Weld Terminals Always On −
Wire
MIG (GMAW)
Electrode Hot
Active
Weld Terminals Always On −
Stick
Stick (SMAW),
Air Carbon Arc (CAC-A) Cutting
And Gouging
Electrode Hot
Active
Weld Terminals Always On −
TIG, Scratch Start
TIG Scratch Start (GTAW)
Electrode Hot
Active
OM-4420 Page 26
6-4. Using Remote Voltage/Amperage Control
1
Remote 14 Receptacle RC14
Connect optional remote control to
RC14 (see Section 5-10).
1
803 454
In Example:
Process = Stick (Using Remote On/Off)
Range = 125 to 400 A DC
Min = 125 A DC
Max = 400 A DC
Example: Combination Remote Amperage Control (Stick)
Max (400 A DC)
Min (125 A DC)
Set V/A
Adjust Switch
Set Remote
Process
Set Range
Control Not
Used In Remote
Stick Mode
Adjust Optional Remote Control
In Example:
Process = TIG (Using Remote On/Off)
Range = 40 to 330 A DC
Percentage Of Range = 50%
Min = 40 A DC
Max = About 185 A DC (50% of 40 to 330)
Example: Combination Remote Amperage Control (TIG)
Max (185 A DC)
Min (40 A DC)
Set V/A
Adjust Switch
Set Remote
Process
Set Range
Set Control
Adjust Optional Remote Control
0774 / Ref. 217 638-A / 802 311-A
OM-4420 Page 27
SECTION 7 − OPERATING AUXILIARY EQUIPMENT
7-1. 120 Volt And 240 Volt Receptacles
1
120 V 20 A AC GFCI
Receptacle GFCI1
2
240 V 30 A AC Twistlock
Receptacle RC1
Receptacles supply 60 Hz singlephase power at weld/power speed.
1
3
2
If a ground fault is detected, GFCI
Reset button pops out and
receptacle does not work. Check
for faulty tools plugged in
receptacle. Press button to reset
GFCI1.
At least once a month, run en-
gine at weld/power speed and
press test button to verify GFCI
is working properly.
4
3
Circuit Breaker CB1
4
Circuit Breaker CB2
CB1 protects RC1 and the generator winding from overload. If CB1
opens, RC1 and GFCI1 do not
work. Place switch in On position to
reset breaker.
CB2 protects GFCI1 from overload.
If CB2 opens, GFCI1 does not
work. Press button to reset breaker.
If a circuit breaker continues to
open, contact Factory Authorized Service Agent.
Generator
power is not affected by weld output.
Maximum output is 2.4 kVA/kW
from GFCI1 and 4 kVA/kW from
RC1. Maximum output from all receptacles is 4 kVA/kW.
EXAMPLE: If 13 A is drawn from
RC1, only 7 A is available at GFCI1:
(240 V x 13 A) + (120 V x 7 A) =
4.0 kVA/kW
191 624
OM-4420 Page 28
7-2. Optional Generator Power Receptacles
European Receptacle
5
1
2
6
1
120 V 20 A AC GFCI
Receptacle GFCI1
2
240 V 16 A AC European
Receptacle RC1
3
240 V 15 A AC Australian
Receptacle RC1
4
240 V 15 A AC South African
Receptacle RC1
Receptacles supply 60 Hz singlephase power at weld/power speed.
If a ground fault is detected, the
GFCI Reset button pops out and
the receptacle does not work.
Check for faulty tools plugged in
receptacle. Press button to reset
GFCI1.
At least once a month, run en-
gine at weld/power speed and
press test button to verify GFCI
is working properly.
Australian Receptacle
5
1
3
5
Circuit Breaker CB2
6
Circuit Breaker CB3
CB2 protects GFCI1 from overload.
If CB2 opens, GFCI1 does not
work. Place button to reset breaker.
6
CB3 protects RC1 from overload. If
CB3 opens, RC1 does not work.
Press button to reset breaker.
If a circuit breaker continues to
open, contact Factory Authorized Service Agent.
Generator
power is not affected by weld output.
South African Receptacle
5
1
4
Maximum output is 2.4 kVA/kW
from GFCI1 and 4 kVA/kW from
RC1. Maximum output from all receptacles is 4 kVA/kW.
EXAMPLE: If 13 A is drawn from
RC1, only 7 A is available at GFCI1:
6
(240 V x 13 A) + (120 V x 7 A) =
4.0 kVA/kW
191 624
OM-4420 Page 29
SECTION 8 − ENGINE/GENERATOR MAINTENANCE
Note
Follow the storage procedure in the engine owner’s manual if the unit will not be used for an
extended period.
8-1. Routine Engine/Generator Maintenance
Stop engine before maintaining.
See Engine Manual and Maintenance Label for
Recycle
engine
fluids.
important start-up, service, and storage information. Service engine more often if used in severe
conditions.
*
To be done by Factory Authorized Service Agent.
Every 8 h
Check Fluid
Levels. See
Section 5-7.
Wipe Up
Spills.
FUEL
WATER
Drain Water
From Fuel
System. See
Section 8-6.
Every 50 h
Clean And
Tighten Weld
Terminals.
Clean Engine
Air Filter.
See Section 8-3.
Every 100 h
Clean And
Tighten
Battery
Connections.
Check Engine Air
Cleaner Hoses
For Cracks And
Loose Clamps.
Every 250 h
Replace
Unreadable
Labels.
1/2 in.
(13 mm)
Inspect
Belts And
Check
Tension.
Check And
Clean Optional
Spark Arrestor.
See Section 8-4.
Clean
Radiator.
Every 500 h
Change Engine Oil
Filter. See Section 8-6.
Service more often in
dirty conditions.
Change Engine Oil.
See Section 8-6.
Repair Or
Replace
Cracked
Cables.
OM-4420 Page 30
Every 1000 h
Service Welding
Generator Brushes
And Slip Rings.
Service More Often
In Dirty Conditions.*
Change Engine
Fuel Filters.
See Section
8-6.
FUEL
SLUDGE
Drain Sludge
From Fuel
Tank. See
Section 8-6.
OR
Check
Engine Valve
Clearance.*
Blow Out Or
Vacuum Inside.
During Heavy
Service,
Clean Monthly.
Every 3000 h
Clean/Set
Engine Fuel
Injectors.*
Every 6000 h / 5 Years
Replace
Engine
Timing Belt.
OM-4420 Page 31
8-2. Engine Maintenance Label
OM-4420 Page 32
8-3. Servicing Air Cleaner
Stop engine.
Do not run engine without air
cleaner or with dirty element. Engine damage caused by using a
damaged element is not covered
by the warranty.
1
Engine Air Cleaner
The air cleaner primary element can
be cleaned but the dirt holding capacity of the filter is reduced with each
cleaning. The chance of dirt reaching
the clean side of the filter while cleaning and the possibility of filter damage
makes cleaning a risk. Consider the
risk of unwarrantable equipment
damage when determining whether
to clean or replace the primary element.
If you decide to clean the primary element, we strongly recommend installing an optional safety element to provide additional engine protection.
Never clean a safety element. Replace the safety element after servicing the primary element three times.
1
2
3
4
Clean or replace primary element if dirty
(see note above before cleaning). Replace primary element if damaged. Replace primary element yearly or after six
cleanings.
5
2
Optional
6
Housing
3
Safety Element (Optional)
4
Primary Element
5
Dust Cap
6
Dust Ejector
To clean air filter:
Wipe off cap and housing. Remove cap
and dump out dust. Remove element(s).
Wipe dust from inside cap and housing
with damp cloth. Reinstall safety element
(if present). Reinstall cap.
Do not clean housing with air
hose.
Clean primary element with compressed
air only.
Air pressure must not exceed 100 psi
(690 kPa). Use 1/8 in (3 mm) nozzle and
keep nozzle at least 2 in (51 mm) from
inside of element. Replace primary element if it has holes or damaged gaskets.
Keep nozzle
2 in (51 mm)
from element.
Reinstall primary element and cap (dust
ejector down).
Blow
Inspect
aircleaner1 9/00 − 803 454 / 153 929-B / 153 585 / Ref. S-0698-B
OM-4420 Page 33
8-4. Inspecting/Cleaning Optional Spark Arrestor Muffler
Stop engine and let cool.
1
Spark Arrestor Muffler
2
Cleanout Plug
Remove plug and remove any dirt
covering cleanout hole.
Start engine and run at idle speed to
blow out cleanout hole. If nothing
blows out of hole, briefly cover end
of exhaust pipe with fireproof
material.
2
1
Stop engine and let cool.
Reinstall cleanout plug.
Tools Needed:
3/8 in
OM-4420 Page 34
803 452 / 803 230
8-5. Adjusting Engine Speed
Stop engine and let cool.
Engine speed is factory set and
should not require adjustment. After tuning engine, check engine no
load speed with a tachometer or frequency meter (see table for no load
speeds). If necessary, adjust speed
as follows:
Start engine and run until warm.
Turn Process/Contactor switch to
Stick − Weld Terminals Always On
position.
1
Throttle Rod
2
Locknut
Loosen locknuts. Place engine
control switch in Run/Idle position.
Wait 15 seconds for throttle solenoid to energize and lower engine
speed to idle rpm.
Turn throttle rod to adjust idle
speed. Tighten locknuts.
3
Engine Speed Adjustment
Screw
4
Locknut
Place engine control switch in Run
position.
Loosen locknut. Turn screw to adjust weld/power speed. Tighten
locknut.
Do not set engine speed higher
than specified.
Stop engine.
Close door.
2
1850 rpm Max.
(61.6 Hz)
1235 rpm
(41.1 Hz)
1
2
3
4
Tools Needed:
3/8, 7/16 in
803 454 / 802 313-A
OM-4420 Page 35
8-6. Servicing Engine Fuel And Lubrication Systems
Tools Needed:
3
1
4
5
7
6
2
803 454
Stop engine and let cool.
After servicing, start engine and
check for fuel leaks. Stop engine,
tighten connections as necessary,
and wipe up spilled fuel.
1
2
3
Oil Filter
Oil Drain Hose And Valve
Oil Fill Cap
4
Primary Fuel Filter (Fuel/Water
Separator)
5
Petcock
6
Secondary Fuel Filter
7
Fuel Tank Sludge Drain Valve
To change oil and filter:
Route engine oil drain hose through hole in
OM-4420 Page 36
base. See engine manual and engine maintenance label for oil specifications.
To drain water from fuel system:
Open primary fuel filter petcock and drain
water into metal container. Close petcock
when water-free fuel flows.
To replace primary fuel filter:
Turn filter counterclockwise. Remove filter.
Apply thin coat of fuel to gasket on new filter.
Fill filter with fuel. Install filter and turn clockwise until tight. Bleed air from fuel system
according to engine manual.
Inspect fuel lines, and replace if cracked or
worn.
To replace secondary fuel filter:
See engine manual.
Close doors.
To drain sludge from fuel tank:
Beware of fire. Do not smoke and
keep sparks and flames away from
drained fuel. Dispose of drained fuel
in an environmentally-safe manner.
Do not leave unit unattended while
draining fuel tank.
Properly lift unit and secure in a level
position. Use adequate blocks or
stands to support unit while draining fuel tank.
Attach 1/2 ID hose to drain valve. Put metal
container under drain, and use screwdriver
to open sludge drain valve. Close valve
when sludge has drained. Remove hose.
8-7. Engine/Generator Overload Protection
Stop engine.
When
a circuit breaker or fuse
opens, it usually indicates a more
serious problem exists. Contact
Factory Authorized Service Agent.
1
2
Fuse F1
Fuse F2
F1 and F2 protect the stator exciter
winding from overload. If F1 opens,
weld and generator power is low or
stops entirely. If F2 opens, weld output
is low or stops entirely. 4 kVA/kW generator power is still available.
2
9
5
Circuit Breaker CB4 (Not Shown)
Circuit Breaker CB5
Circuit Breaker CB6
6
Circuit Breaker CB10 (Not
Shown)
7
Circuit Breaker CB11
8
Circuit Breaker CB12
9
Circuit Breaker CB13
10 Circuit Breaker CB14
(Not Shown)
8
7
4
1
3
4
5
CB4 protects the welding arc drive (dig)
circuit. If CB4 opens, electrode may
stick to the workpiece more frequently
during low voltage (short arc length)
conditions. CB4 automatically resets
when the fault is corrected.
CB5 protects the 24 volt ac output to remote receptacle RC14, and 24 volt output to field current regulator board PC1.
If CB5 opens, weld output and 24 volt
output to RC14 stops. On units with optional power plant, power at receptacle
RC5 also stops if CB5 opens.
CB6 protects the 115 volt ac output to
remote receptacle RC14. If CB6 opens,
115 volt output to RC14 stops.
CB10 protects the engine battery circuit. If CB10 opens, the engine will not
crank. CB10 automatically resets when
the fault is corrected.
CB11 protects the engine wiring harness. If CB11 opens, weld output stops
(generator power is still available).
CB12 protects the field flashing circuit.
If CB12 opens, the generator may not
excite at start-up and weld and generator power output may not be available.
CB13 protects the engine shutdown circuit. If CB13 opens, the engine cranks
but does not start.
Press button to reset breaker.
CB14 protects the throttle solenoid. If
CB14 opens, the engine will not run at
idle speed. CB14 automatically resets
when the fault is corrected.
Ref. 803 229
OM-4420 Page 37
SECTION 9 − TROUBLESHOOTING
9-1. Troubleshooting Tables
A. Welding
Trouble
Remedy
No weld output; generator power output Place Process/Contactor switch in a Weld Terminals Always On position, or place switch in a Remote
okay at ac receptacles.
position and connect remote contactor to Remote 14 receptacle RC14 (see Sections 5-10 and 6-1).
Check position of Ampere Range switch.
Reset circuit breaker CB11 (see Section 8-7).
Reset circuit breaker CB5 (see Section 8-7). Check for faulty remote device connected to RC14.
Check and secure connections to Remote 14 receptacle RC14 (see Section 5-10).
Have Factory Authorized Service Agent check connector board PC6 and connections.
Check fuse F2, and replace if open (see Section 8-7). Have Factory Authorized Service Agent check
brushes and slip rings, field excitation circuit, field current regulator board PC1, and the rotor.
No weld output or generator power Disconnect equipment from generator power receptacles during start-up.
output.
Check fuses F1 and F2, and replace if open (see Section 8-7). Have Factory Authorized Service Agent
check integrated rectifier SR1, capacitor C9, field current regulator board PC1, and the rotor.
Reset circuit breaker CB12 (see Section 8-7).
Have Factory Authorized Service Agent check brushes and slip rings, and field excitation circuit.
Erratic weld output.
Check and tighten connections inside and outside unit.
Be sure connection to work piece is clean and tight.
Use dry, properly stored electrodes.
Remove excessive coils from weld cables.
Have Factory Authorized Service Agent check brushes and slip rings.
High weld output.
Check position of Ampere Range switch and Voltage/Amperage Adjust control.
Check engine weld/power speed, and adjust if necessary (see Section 8-5).
Have Factory Authorized Service Agent check field current regulator board PC1.
Voltage/Amperage control does not Place Ampere Range switch in lower range. Voltage/Amperage control does not work with Ampere
work when welding in Stick mode.
Range switch in highest range.
Low weld output.
Check position of Ampere Range switch and Voltage/Amperage Adjust control.
Check engine weld/power speed, and adjust if necessary (see Section 8-5).
Check fuses F1 and F2, and replace if open (see Section 8-7). Have Factory Authorized Service Agent
check integrated rectifier SR1, capacitor C9, field current regulator board PC1, and the rotor.
Electrode sticks to the workpiece more Circuit breaker CB4 may be open. CB4 automatically resets when the fault is corrected (see Section 8-7).
frequently during low voltage (short arc Have Factory Authorized Service Agent check transformer T1 and integrated rectifiers SR4 and SR5.
length) conditions.
Low open-circuit voltage.
Check engine weld/power speed, and adjust if necessary.
Check position of Process/Contactor switch.
OM-4420 Page 38
Trouble
Remedy
No remote fine amperage or voltage Place Voltage/Amperage Adjust switch in Remote position.
control.
Check and secure connections to Remote 14 receptacle RC14 (see Section 5-10).
Repair or replace remote control device.
Have Factory Authorized Service Agent check PC1 current sensing leads (36 and 37), and connections.
Constant speed wire feeder does not Reset circuit breaker(s) CB5 and CB13 (see Section 8-7).
work.
Check and secure connections to Remote 14 receptacle RC14 (see Section 5-10).
Repair or replace wire feeder.
Low CV weld output.
Set Ampere Range switch to highest range.
Increase Voltage/Amperage Adjust Control setting.
Min or max CV weld output only.
Check position of Voltage/Amperage Adjust control and Voltage/Amperage Adjust switch.
Repair or replace remote control device.
Have Factory Authorized Service Agent check field current regulator board PC1.
B. Generator Power
Trouble
Remedy
No generator power output at ac recep- Reset receptacle circuit breakers.
tacles; weld output okay.
Reset GFCI receptacle.
No generator power or weld output.
Disconnect equipment from generator power receptacles during start-up.
Check fuses F1 and F2, and replace if open (see Section 8-7). Have Factory Authorized Service Agent
check integrated rectifier SR1, capacitor C9, diode/capacitor board D1/C1, and the rotor.
Reset circuit breaker CB12. Have Factory Authorized Service Agent check field current regulator board
PC1 (see Section 8-7).
Have Factory Authorized Service Agent check brushes and slip rings, and field excitation circuit.
High output
receptacles.
at
generator
power Check engine weld/power speed, and adjust if necessary (see Section 8-5).
Have Factory Authorized Service Agent adjust field current resistor R3.
Low output
receptacles.
at
generator
power Check engine weld/power speed, and adjust if necessary (see Section 8-5).
Check fuse F1, and replace if open (see Section 8-7). Have Factory Authorized Service Agent check integrated rectifier SR1, resistor R3, and capacitor C9.
C. Engine
Trouble
Engine will not crank.
Remedy
Check battery, and replace if necessary.
Check battery connections and tighten if necessary.
Circuit breaker CB10 may be open. CB10 automatically resets when fault is corrected (see Section 8-7).
Have Factory Authorized Service Agent check engine wiring harness and components.
Check engine wiring harness plug connections.
Turn optional battery disconnect switch to On position (see Section 5-6).
Have Factory Authorized Service Agent check Engine Control switch S1, control relay CR1, and diode/
capacitor board D8/C8.
OM-4420 Page 39
Trouble
Engine cranks but does not start.
Remedy
Check fuel level. Optional low fuel shutdown stops engine if fuel level is low.
Reset circuit breaker CB13 (see Section 8-7). Have Factory Authorized Service Agent check engine wiring harness and components.
Check battery and replace if necessary. Check engine charging system according to engine manual.
Have Factory Authorized Service Agent check time delay relay TD1, control relay CR5, fuel pump,
and fuel solenoid FS1.
Air in fuel system. See engine manual.
Engine starts, but stops when Engine Check oil level. Automatic shutdown system stops engine if oil pressure is too low or engine temperature
Control switch is released.
is too high (see Section 5-7).
Have Factory Authorized Service Agent check time delay relay TD1, and control relay CR5.
Engine hard to start in cold weather.
Use starting aid switch (see Section 6-1). If Starting Aid switch does not work have Factory Authorized
Service Agent check Engine Control switch S2, and control relay CR8.
Keep battery in good condition. Store battery in warm area off cold surface.
Use fuel formulated for cold weather (diesel fuel can gel in cold weather). Contact local fuel supplier for
fuel information.
Use correct grade oil for cold weather (see Section 8-2 ).
Engine suddenly stops.
Check fuel level. Optional low fuel shutdown stops engine if fuel level is low.
Check oil level. Automatic shutdown system stops engine if oil pressure is too low or engine temperature
is too high (see Section 5-7).
Have Factory Authorized Service Agent check time delay relay TD1, control relay CR5, fuel pump,
and fuel solenoid FS1.
See engine manual.
Engine slowly stopped and cannot be
restarted.
Check fuel level.
Check engine air and fuel filters (see Sections 8-3 and 8-6).
See engine manual.
Battery discharges between uses.
Turn Engine Control switch S1 off when unit is not running.
Clean top of battery with baking soda and water solution; rinse with clear water.
Recharge or replace battery if necessary.
Periodically recharge battery (approximately every 3 months).
Engine idles, but does not come up to
weld speed.
Have Factory Authorized Service Agent check idle module PC7.
Check for obstructed throttle solenoid.
Engine does not run at idle speed.
Turn Process/Contactor switch to any position but Remote-TIG.
Check for obstructed throttle solenoid.
Allow circuit breaker CB14 to reset. Have Factory Authorized Service Agent check throttle solenoid TS1
and linkage (see Section 8-7).
Have Factory Authorized Service Agent check idle module PC7, control relays CR3 and CR6, and current
transformer CT1.
Engine uses oil during run-in period; Dry engine (see Section 11).
wetstacking occurs.
OM-4420 Page 40
Notes
Start Your Professional
Welding Career Now!
400 Trade Square East, Troy, Ohio 45373
1-800-332-9448 www.welding.org
Over 80,000 trained
since 1930!
OM-4420 Page 41
SECTION 10 − ELECTRICAL DIAGRAM
Figure 10-1. Circuit Diagram For Welding Generator
OM-4420 Page 42
217 852-C
OM-4420 Page 43
SECTION 11 − RUN-IN PROCEDURE
run_in1 8/01
11-1. Wetstacking
Do not perform run-in
procedure at less than 20
volts weld output and do not
exceed duty cycle or equipment damage may occur.
1
2
Welding Generator
Run diesel engines near rated voltage and current during run-in period
to properly seat piston rings and
prevent wetstacking. See nameplate, rating label, or specifications
section in this manual to find rated
voltage and current.
1
2
Do not idle engine longer than
necessary. Piston rings seat
faster if engine runs at weld/
power rpm, and the welding
generator is kept loaded during
run-in.
Engine Exhaust Pipe
Wetstacking is unburned fuel and
oil in the exhaust pipe and occurs
during run-in if the engine is run too
long at light load or idle rpm.
If exhaust pipe is coated with a wet,
black, tar-like substance, dry the
engine using one of the following
run-in procedures.
See the engine manual for additional engine run-in information.
OM-4420 Page 44
11-2. Run-In Procedure Using Load Bank
Stop engine.
Do not touch hot exhaust
pipe, engine parts, or load
bank/grid.
Keep exhaust and pipe away
from flammables.
4
2
1
Do not perform run-in
procedure at less than 20
volts weld output and do not
exceed duty cycle or equipment damage may occur.
1 Load Bank
Turn all load bank switches Off. If
needed, connect load bank to 115
volts ac wall receptacle or generator auxiliary power receptacle.
2 Welding Generator
Place A/V range switch in maximum position, A/V control in minimum position, and Output Selector
switch (if present) in either DC
position.
3 Weld Cables
Connect load bank to generator
weld output terminals using proper
size weld cables with correct
connectors. Observe
correct
polarity.
3
Start engine and run for several
minutes.
Set load bank switches and then
adjust generator A/V control so load
equals rated voltage and current of
generator (see nameplate, rating
label, or the specifications section
in this manual).
Check generator and load bank
meters after first five minutes then
every fifteen minutes to be sure
generator is loaded properly.
Check oil level frequently during run-in; add oil if needed.
After one hour (minimum) place A/V
control in minimum position, then
turn off load bank to remove load.
Run engine several minutes at no
load.
Stop engine and let cool.
4 Engine Exhaust Pipe
Repeat procedure if wetstacking is
present.
S-0683
OM-4420 Page 45
11-3. Run-In Procedure Using Resistance Grid
Stop engine.
Do not touch hot exhaust
pipe, engine parts, or load
bank/grid.
Keep exhaust and pipe away
from flammables.
6
Do not perform run-in
procedure at less than 20
volts weld output and do not
exceed duty cycle or equipment damage may occur.
2
1 Resistance Grid
Use grid sized for generator rated
output.
1
Turn Off grid.
2 Welding Generator
Place A/V range switch in maximum position, A/V control in minimum position, and Output Selector
switch (if present) in either DC
position.
3 Weld Cables
Connect grid to generator weld
output terminals using proper size
weld cables with correct connectors (polarity is not important).
4
3
5
Voltmeter
5 Clamp-On Ammeter
Connect voltmeter and ammeter as
shown, if not provided on generator.
Start engine and run for several
minutes.
Set grid switches and then adjust
generator A/V control so load
equals rated voltage and current of
the generator (see nameplate, rating label, or the specifications section in this manual).
4
+
Check generator and meters after
first five minutes then every fifteen
minutes to be sure generator is
loaded properly.
Check oil level frequently during run-in; add oil if needed.
After one hour (minimum), place
A/V control in minimum position,
then shut down grid to remove load.
Run engine several minutes at no
load.
Stop engine and let cool.
6 Engine Exhaust Pipe
Repeat procedure if wetstacking is
present.
S-0684
OM-4420 Page 46
SECTION 12 − GENERATOR POWER GUIDELINES
NOTE
The views in this section are intended to be representative of all engine-driven
welding generators. Your unit may differ from those shown.
12-1. Selecting Equipment
1
2
3
Generator Power Receptacles
− Neutral Bonded To Frame
3-Prong Plug From Case
Grounded Equipment
2-Prong Plug From Double
Insulated Equipment
Do not use 2-prong plug unless equipment is double insulated.
1
2
3
Be sure equipment
has this symbol
and/or wording.
OR
gen_pwr 11/02 − Ref. ST-159 730 / ST-800 577
12-2. Grounding Generator To Truck Or Trailer Frame
Always ground generator
frame to vehicle frame to prevent electric shock and static
electricity hazards.
1
2
3
1
GND/PE
Equipment Grounding
Terminal (On Front Panel)
Grounding Cable (Not
Supplied)
Metal Vehicle Frame
Connect cable from equipment
ground terminal to metal vehicle
frame. Use #10 AWG or larger
insulated copper wire.
2
3
If unit does not have GFCI receptacles, use GFCI-protected extension cord.
Electrically bond generator
frame to vehicle frame by
metal-to-metal contact.
Bed liners, shipping skids, and some running
gear insulate the welding generator from the vehicle frame. Always connect a ground wire from
the generator equipment grounding terminal to
bare metal on the vehicle frame as shown.
S-0854
OM-4420 Page 47
12-3. Grounding When Supplying Building Systems
1
1
2
Equipment Grounding
Terminal
Grounding Cable
2
GND/PE
Use #10 AWG or larger insulated
copper wire.
3
Ground Device
Ground generator to system
earth ground if supplying
power to a premises (home,
shop, farm) wiring system.
2
Use ground device as stated
in electrical codes.
3
ST-800 576-B
12-4. How Much Power Does Equipment Require?
1
3
2
1
VOLTS 115
AMPS 4.5
Hz
60
Resistive Load
A light bulb is a resistive load and
requires a constant amount of power.
2
Non-Resistive Load
Equipment with a motor is a non-resistive load and requires approximately six times more power while
starting the motor than when running
(see Section 12-8).
3
3
Rating Data
Rating shows volts and amperes, or
watts required to run equipment.
AMPERES x VOLTS = WATTS
EXAMPLE 1: If a drill uses 4.5 amperes at 115 volts, calculate its running power
requirement in watts.
4.5 A x 115 V = 520 W
The load applied by the drill is 520 watts.
EXAMPLE 2: If three 200 watt flood lamps are used with the drill from Example 1,
add the individual loads to calculate total load.
(200 W + 200 W + 200 W) + 520 W = 1120 W
The total load applied by the three flood lamps and drill is 1120 watts.
S-0623
OM-4420 Page 48
12-5. Approximate Power Requirements For Industrial Motors
Industrial Motors
Split Phase
Capacitor Start-Induction Run
Capacitor Start-Capacitor Run
Fan Duty
Rating
Starting Watts
Running Watts
1/8 HP
1/6 HP
1/4 HP
1/3 HP
1/2 HP
1/3 HP
1/2 HP
3/4 HP
1 HP
1-1/2 HP
2 HP
3 HP
5 HP
1-1/2 HP
5 HP
7-1/2 HP
10 HP
1/8 HP
1/6 HP
1/4 HP
1/3 HP
1/2 HP
800
1225
1600
2100
3175
2020
3075
4500
6100
8200
10550
15900
23300
8100
23300
35000
46700
1000
1400
1850
2400
3500
300
500
600
700
875
720
975
1400
1600
2200
2850
3900
6800
2000
6000
8000
10700
400
550
650
800
1100
12-6. Approximate Power Requirements For Farm/Home Equipment
Farm/Home Equipment
Stock Tank De-Icer
Grain Cleaner
Portable Conveyor
Grain Elevator
Milk Cooler
Milker (Vacuum Pump)
FARM DUTY MOTORS
Std. (e.g. Conveyors,
Feed Augers, Air
Compressors)
High Torque (e.g. Barn
Cleaners, Silo Unloaders,
Silo Hoists, Bunk Feeders)
3-1/2 cu. ft. Mixer
High Pressure 1.8 Gal/Min
Washer 2 gal/min
2 gal/min
Refrigerator or Freezer
Shallow Well Pump
Sump Pump
Rating
1/4 HP
1/2 HP
3/4 HP
2 HP
1/3 HP
1/2 HP
3/4 HP
1 HP
1-1/2 HP
2 HP
3 HP
5 HP
1-1/2 HP
5 HP
7-1/2 HP
10 HP
1/2 HP
500 PSI
550 PSI
700 PSI
1/3 HP
1/2 HP
1/3 HP
1/2 HP
Starting Watts
Running Watts
1000
1650
3400
4400
2900
10500
1720
2575
4500
6100
8200
10550
15900
23300
8100
23300
35000
46700
3300
3150
4500
6100
3100
2150
3100
2100
3200
1000
650
1000
1400
1100
2800
720
975
1400
1600
2200
2850
3900
6800
2000
6000
8000
10700
1000
950
1400
1600
800
750
1000
800
1050
OM-4420 Page 49
12-7. Approximate Power Requirements For Contractor Equipment
Contractor
Hand Drill
Circular Saw
Table Saw
Band Saw
Bench Grinder
Air Compressor
Electric Chain Saw
Electric Trimmer
Electric Cultivator
Elec. Hedge Trimmer
Flood Lights
Submersible Pump
Centrifugal Pump
Floor Polisher
High Pressure Washer
55 gal Drum Mixer
Wet & Dry Vac
OM-4420 Page 50
Rating
Starting Watts
Running Watts
1/4 in
3/8 in
1/2 in
6-1/2 in
7-1/4 in
8-1/4 in
9 in
10 in
14 in
6 in
8 in
10 in
1/2 HP
1 HP
1-1/2 HP
2 HP
1-1/2 HP, 12 in
2 HP, 14 in
Standard 9 in
Heavy Duty 12 in
1/3 HP
18 in
HID
Metal Halide
Mercury
Sodium
Vapor
400 gph
900 gph
3/4 HP, 16 in
1 HP, 20 in
1/2 HP
3/4 HP
1 HP
1/4 HP
1.7 HP
2-1/2 HP
350
400
600
500
900
1400
4500
6300
2500
1720
3900
5200
3000
6000
8200
10500
1100
1100
350
500
2100
400
125
313
1000
1400
1250
600
900
4500
6100
3150
4500
6100
1900
900
1300
350
400
600
500
900
1400
1500
1800
1100
720
1400
1600
1000
1500
2200
2800
1100
1100
350
500
700
400
100
250
1000
200
500
1400
1600
950
1400
1600
700
900
1300
12-8. Power Required To Start Motor
4
1
3
AC MOTOR
VOLTS 230
AMPS 2.5
CODE M
Hz
60
HP
1/4
PHASE 1
1
2
3
4
2
Motor Start Code
Running Amperage
Motor HP
Motor Voltage
To find starting amperage:
Step 1: Find code and use table to
find kVA/HP. If code is not listed,
multiply running amperage by six to
find starting amperage.
Step 2: Find Motor HP and Volts.
Step 3: Determine starting amperage (see example).
Welding generator amperage output must be at least twice the
motor’s running amperage.
Single-Phase Induction Motor Starting Requirements
Motor Start
Code
G
H
J
K
L
M
N
P
KVA/HP
6.3
7.1
8.0
9.0
10.0
11.2
12.5
14.0
kVA/HP x HP x 1000
VOLTS
= STARTING AMPERAGE
EXAMPLE: Calculate the starting amperage required for a 230 V, 1/4
HP motor with a motor start code of M.
Volts = 230
HP = 1/4
Using Table, Code M results in kVA/HP = 11.2
11.2 x 1/4 x 1000
= 12.2 A Starting the motor requires 12.2 amperes.
230
S-0624
12-9. How Much Power Can Generator Supply?
1
Limit Load To 90% Of
Generator Output
Always start non-resistive (motor)
loads in order from largest to smallest, and add resistive loads last.
2
1
2
5 Second Rule
If motor does not start within 5
seconds, turn off power to prevent
motor damage. Motor requires
more power than generator can
supply.
Ref. ST-800 396-A / S-0625
OM-4420 Page 51
12-10. Typical Connections To Supply Standby Power
Properly install and ground this equipment according to
its Owner’s Manual and national, state, and local codes.
1
2
Utility
Electrical
Service
3
Transfer Switch
4
Fused
Disconnect
Switch
(If Required)
Welding
Generator
Output
5
Essential
Loads
Have only qualified persons perform
these connections according to all
applicable codes and safety practices.
Switch transfers the electrical load from
electric utility service to the generator. Transfer load back to electric utility when service is
restored.
Properly install and ground this
equipment according to its Owner’s
Manual and national, state, and local
codes.
Install correct switch (customer-supplied).
Switch rating must be same as or greater
than the branch overcurrent protection.
Customer-supplied
equipment is required if generator will supply standby
power during emergencies or power outages.
1 Utility Electrical Service
2 Transfer Switch (Double-Throw)
3 Fused Disconnect Switch
Install correct switch (customer-supplied) if
required by electrical code.
4 Welding Generator Output
Generator output voltage and wiring must be
consistent with regular (utility) system voltage and wiring.
Connect generator with temporary or permanent wiring suitable for the installation.
Turn off or unplug all equipment connected to
generator before starting or stopping engine.
When starting or stopping, the engine has
low speed which causes low voltage and
frequency.
5 Essential Loads
Generator output may not meet the electrical
requirements of the premises. If generator
does not produce enough output to meet all
requirements, connect only essential loads
(pumps, freezers, heaters, etc. − See Section 12-4).
Notes
Work like a Pro!
Pros weld and cut
safely. Read the
safety rules at
the beginning
of this manual.
OM-4420 Page 52
12-11. Selecting Extension Cord (Use Shortest Cord Possible)
Cord Lengths for 120 Volt Loads
If unit does not have GFCI receptacles, use GFCI-protected extension cord.
Maximum Allowable Cord Length in ft (m) for Conductor Size (AWG)*
Current
(Amperes)
Load (Watts)
5
600
7
840
10
1200
15
4
6
8
10
12
14
350 (106)
225 (68)
137 (42)
100 (30)
400 (122)
250 (76)
150 (46)
100 (30)
62 (19)
400 (122)
275 (84)
175 (53)
112 (34)
62 (19)
50 (15)
1800
300 (91)
175 (53)
112 (34)
75 (23)
37 (11)
30 (9)
20
2400
225 (68)
137 (42)
87 (26)
50 (15)
30 (9)
25
3000
175 (53)
112 (34)
62 (19)
37 (11)
30
3600
150 (46)
87 (26)
50 (15)
37 (11)
35
4200
125 (38)
75 (23)
50 (15)
40
4800
112 (34)
62 (19)
37 (11)
45
5400
100 (30)
62 (19)
50
6000
87 (26)
50 (15)
*Conductor size is based on maximum 2% voltage drop
Cord Lengths for 240 Volt Loads
If unit does not have GFCI receptacles, use GFCI-protected extension cord.
Maximum Allowable Cord Length in ft (m) for Conductor Size (AWG)*
Current
(Amperes)
Load (Watts)
5
1200
7
1680
10
2400
15
4
6
8
10
12
14
700 (213)
450 (137)
225 (84)
200 (61)
800 (244)
500 (152)
300 (91)
200 (61)
125 (38)
800 (244)
550 (168)
350 (107)
225 (69)
125 (38)
100 (31)
3600
600 (183)
350 (107)
225 (69)
150 (46)
75 (23)
60 (18)
20
4800
450 (137)
275 (84)
175 (53)
100 (31)
60 (18)
25
6000
350 (107)
225 (69)
125 (38)
75 (23)
30
7000
300 (91)
175 (53)
100 (31)
75 (23)
35
8400
250 (76)
150 (46)
100 (31)
40
9600
225 (69)
125 (38)
75 (23)
45
10,800
200 (61)
125 (38)
50
12,000
175 (53)
100 (31)
*Conductor size is based on maximum 2% voltage drop
OM-4420 Page 53
SECTION 13 − SELECTING AND PREPARING
TUNGSTEN ELECTRODE
gtaw 7/97
NOTE
For additional information, see your distributor for a handbook on the Gas
Tungsten Arc Welding (GTAW) process.Wear clean gloves to prevent
contamination of tungsten electrode.
13-1. Selecting Tungsten Electrode
Amperage Range - Gas Type♦ - Polarity
Electrode Diameter
DC − Argon − Electrode
Negative/Straight Polarity
DC − Argon − Electrode
Positive/Reverse Polarity
AC − Argon − Using
High Frequency
AC − Argon − Balanced
Wave Using High Freq.
.010”
Up to 15
*
Up to 15
Up to 10
.020”
5-20
*
5-20
10-20
Pure Tungsten
(Green Band)
.040”
15-80
*
10-60
20-30
1/16”
70-150
10-20
50-100
30-80
3/32”
125-225
15-30
100-160
60-130
1/8”
225-360
25-40
150-210
100-180
5/32”
360-450
40-55
200-275
160-240
3/16”
450-720
55-80
250-350
190-300
1/4”
720-950
80-125
325-450
250-400
.010”
Up to 25
*
Up to 20
Up to 15
.020”
15-40
*
15-35
5-20
.040”
25-85
*
20-80
20-60
1/16”
50-160
10-20
50-150
60-120
3/32”
135-235
15-30
130-250
100-180
1/8”
250-400
25-40
225-360
160-250
5/32”
400-500
40-55
300-450
200-320
2% Thorium Alloyed
Tungsten (Red Band)
3/16”
500-750
55-80
400-500
290-390
1/4”
750-1000
80-125
600-800
340-525
.010”
*
*
Up to 20
Up to 15
.020”
*
*
15-35
5-20
.040”
*
*
20-80
20-60
1/16”
*
*
50-150
60-120
3/32”
*
*
130-250
100-180
Zirconium Alloyed Tungsten (Brown Band)
1/8”
*
*
225-360
160-250
5/32”
*
*
300-450
200-320
3/16”
*
*
400-550
290-390
1/4”
*
*
600-800
340-525
♦Typical argon shielding gas flow rates are 15 to 35 cfh (cubic feet per hour).
*Not Recommended.
The figures listed are intended as a guide and are a composite of recommendations from American Welding Society (AWS) and electrode
manufacturers.
OM-4420 Page 54
13-2. Preparing Tungsten For AC Or DC Electrode Positive (DCEP) Welding
1
2
Tungsten Electrode
Balled End
Understand and
follow
safety symbols at start of
Section 14-1 before preparing tungsten.
1
Ball end of tungsten before welding
by applying either an ac amperage
slightly higher than what is recommended for a given electrode diameter (see Section 13-1), or a dc
electrode positive amperage.
1-1/2 Times
Electrode Diameter
2
Ref. S-0161
13-3. Preparing Tungsten For DC Electrode Negative (DCEN) Welding
1
1
2
2
Tungsten Electrode
Tapered End
Grind end of tungsten on fine grit,
hard abrasive wheel before welding. Do not use wheel for other jobs
or tungsten can become contaminated causing lower weld quality.
2-1/2 Times
Electrode Diameter
1
2
3
1
2
Stable Arc
Flat
Diameter of this flat determines
amperage capacity.
3
4
Grinding Wheel
Straight Ground
1
2
3
4
Arc Wander
Point
Grinding Wheel
Radial Ground
4
Ideal Tungsten Preparation − Stable Arc
1
2
3
4
Wrong Tungsten Preparation − Wandering Arc
Ref. S-0161 / Ref. S-0162
OM-4420 Page 55
SECTION 14 − GUIDELINES FOR TIG WELDING (GTAW)
14-1. Positioning The Torch
Weld current can damage
electronic parts in vehicles.
Disconnect both battery
cables before welding on a
vehicle. Place work clamp as
close to the weld as possible.
3
1
Workpiece
Make sure workpiece is clean
before welding.
2
2
Work Clamp
Place as close to the weld as
possible.
4
3
4
5
90°
Torch
Filler Rod (If Applicable)
Tungsten Electrode
Select and prepare tungsten
according to Sections 13-1, and
13-2 or 13-3.
1
Tungsten extension is the distance
the tungsten extends out gas cup of
torch.
Arc length is the distance from the
tungsten to the workpiece.
10−15°
As a general guide, start with an
extension and arc length equal to
diameter of tungsten.
4
5
10−25°
ST-161 892
14-2. Torch Movement During Welding
Tungsten Without Filler Rod
75°
Welding direction
Form pool
Tilt torch
Move torch to front
of pool. Repeat process.
Tungsten With Filler Rod
75°
Welding direction
Form pool
Tilt torch
Remove rod
OM-4420 Page 56
15°
Add filler metal
Move torch to front
of pool. Repeat process.
ST-162 002-B
14-3. Positioning Torch Tungsten For Various Weld Joints
90°
Butt Weld And Stringer Bead
70°
20°
20°
“T” Joint
70°
10°
20°
40°
Lap Joint
70°
20°
30°
90°
Corner Joint
70°
20°
ST-162 003 / S-0792
OM-4420 Page 57
SECTION 15 − PARTS LIST
Hardware is common and not
available unless listed.
15
3
16
17
2
18
19
1
6
7
14
13
20
11
5
21
10
4
12
9
22
8
121
113
23
24
120
110
119 − Figure 15-5
114
104
13
112
111 − Figure 15-2
118
105
106
107
108
115
116
109
117 − Figure 15-3
Figure 15-1. Main Assembly
OM-4420 Page 58
125
36
34
35
33
31
30
32
27
37
29
28
59
58
26
39
25
57
53
38
51
49
45
124
42
50
62
54
52
47
43
44
63
46
64
48
122
41
123
40
72
65
62
66
67
68
77
93 − Figure 15-4
60
61
56
55
76
73
75 74
70
71
78 79
69
81
87
85
94
95
96
97
98
86
82
80
99
83
88
84
100
101
91
102
89
92
90
103
803 455
OM-4420 Page 59
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 15-1. Main Assembly
. . . 1 . . . . . . . . . . . . . . 189824
. . . 2 . . . . . . . . . . . . . . 189828
. . . 3 . . . . . . . . . . . . . . 206601
. . . 4 . . . . . Z1 . . . . . 208277
. . . 5 . . . . . . . . . . . . . . 038620
. . . . . . . . . . . 1T . . . . . 189549
. . . 6 . . . . . . . . . . . . . . 038621
. . . 7 . . . . . . . . . . . . . . 081499
. . . . . . . . . . . . . . . . . . . . 138027
. . . . . . . . . . . . . . . . . . . . 020225
. . . 8 . . SR4, SR5 . . 035704
. . . 9 . . . . CB4 . . . . 045061
. . . 10 . . . . . . . . . . . . . . 206352
. . . 11 . . . . . T1 . . . . . 205636
. . . 12 . . . . . . . . . . . . . . 201697
. . . 13 . . . . . . . . . . . . . . 173352
. . . 14 . . . . . . . . . . . . . . 189708
. . . 15 . . . . . . . . . . . . . . 194485
. . . 16 . . . . . . . . . . . . . . 189764
. . . . . . . . . . . . . . . . . . . *192938
. . . . . . . . . . . . . . . . . . . *192939
. . . . . . . . . . . . . . . . . . . . 206556
. . . 17 . . . . . . . . . . . . . . 189763
. . . 18 . . . . . . . . . . . . . . 206351
. . . 19 . . . . . . . . . . . . . . 189464
. . . 20 . . . . . . . . . . . . ♦209612
. . . 21 . . . . . . . . . . . . ♦209597
. . . 22 . . . . . . . . . . . . . ♦209611
. . . 23 . . . . . . . . . . . . . . 196220
. . . 24 . . . . . . . . . . . . . . 192362
. . . 25 . . . . . . . . . . . . . +206603
. . . 26 . . . . . . . . . . . . . . 189052
. . . 27 . . . . . . . . . . . . . . 190198
. . . 28 . . . . . . . . . . . . . . 176103
. . . 29 . . . . . . . . . . . . . . 176104
. . . 30 . . . . . . . . . . . . ♦143915
. . . 31 . . . . . . . . . . . . ♦205702
. . . 32 . . . . . . . . . . . . ♦205749
. . . 33 . . . . . . . . . . . . ♦603767
. . . 34 . . . . . . . . . . . . ♦010875
. . . 35 . . . . . . . . . . . . ♦205712
. . . 36 . . . . . . . . . . . . ♦205748
. . . 37 . . . . . . . . . . . . . . 176230
. . . 38 . . . . . . . . . . . . . . 213895
. . . 39 . . . . . . . . . . . . . . 202633
. . . 40 . . . . . . . . . . . . . . 191577
. . . 41 . . . . . . . . . . . . . . 191809
. . . 42 . . . . . . . . . . . . . . 209632
OM-4420 Page 60
. . Panel, Gen LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Panel, Engine Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Panel, Engine Extension LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Reactor, AC Environmental Rda . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Link, Jumper Term Blk 30 Amp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Block, Term Assy Standard W/Clamp (includes) . . . . . . . . . . . . . . . . . . . . .
. . . . Block, Term 30 Amp 4 Pole Frict Term Str Both Side . . . . . . . . . . . . . . .
. . . . Bracket, Mtg Strip Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Edge Trim, Style Tl750−b2x1/16 Black W/Clips 3.750 . . . . . . . . . . . . . .
. . . . Clamp, Nyl .875 Clamp Dia X.500 Wide .203 Mtg Hole . . . . . . . . . . . . .
. . Rectifier, Integ Bridge 40 Amp 800 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Circuit Breaker, Auto Reset 24vdc 7 Amp . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Brace, Front To Center Upright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Transformer, W/Brkt Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pan, Reactor And Rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Extrusion, Rubber (order by ft.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Firewall, Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Hose, Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Air Cleaner, Intake (Engine) (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Filter, Air Element Primary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Filter, Air Element Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pipe, Air Cleaner Intake Deutz (Turbo Hose To Air Cleaner Hose) . . . . .
. . Bracket, Mtg Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Upright, Center Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Seal, Weather Lift Eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Lever, Switch Lockout Disconnect Battery . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Battery Disconnect Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Switch, Disc Battery 2P 6−36 Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Holddown Fuel Tank Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Nyl 1/2 Conduit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Cover, Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Grommet, Plastic Neck Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Cap, Tank Screw−on 3.500 In W/Vent W/Lanyard 8” . . . . . . . . . . . . . . . . .
. . Label, Use Diesel Fuel Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Warning Falling Equipment Can Cause Serious . . . . . . . . . . . . . . .
. . Mount, Sgl Stud 1.5 Dia X 1.000 Lg .312−18 Stud . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pipe, Exhaust Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Cap, Weather Exhaust No. 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Clamp, Muffler 2.000 Dia U Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pipe, Exhaust Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Hot Exhaust Parts Do Not Touch . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Manifold, Exhaust Muffler Bf4m2011 Deutz . . . . . . . . . . . . . . . . . . . . . . . . .
. . Support, Cover E−coat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Guard, Starter Deutz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Engine LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Hose, Tubing Oil Assyw/Fittings 22.380lg . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
2
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 15-1. Main Assembly (Continued)
. . . 43 . . . . . . . . . . . . . . 218619
. . . . . . . . . . . . . . . . . . . . 193256
. . . . . . . . . . . . . . . . . . . . 195748
. . . . . . . . . . . . . . . . . . . . 195746
. . . . . . . . . . . . . . . . . . . . 195745
. . . . . . . . . . . . . . . . . . . *067265
. . . . . . . . . . . . . . . . . . . *066217
. . . . . . . . . . . . . . . . . . . . 208041
. . . . . . . . . . . . . . . . . . . . 193230
. . . . . . . . . . . . . . . . . . . . 194403
. . . . . . . GLOW PLUG . 190059
. . . 44 . . . . . . . . . . . . . . 207203
. . . . . . . . . . . . . . . . . . . . 208042
. . . 45 . . . . . . . . . . . . . *207808
. . . 46 . . . . . . . . . . . . . . 209675
. . . 47 . . . . . . . . . . . . . . 209633
. . . 48 . . . . . . . . . . . . . . 209621
. . . 49 . . . . . . . . . . . . . . 207269
. . . 50 . . . . . . . . . . . . . . 206749
. . . 51 . . . . . . . . . . . . . . 206558
. . . 52 . . . . . . . . . . . . . . 209623
. . . 53 . . . . . . . . . . . . . . 201749
. . . 54 . . . . . . . . . . . . . . 201006
. . . 55 . . . . BATT . . . . 190897
. . . 56 . . . . . . . . . . . . . . 108081
. . . 57 . . . . . . . . . . . . . . 190206
. . . 58 . . . . . . . . . . . . . . 190207
. . . 59 . . . . . . . . . . . . . . 203430
. . . 60 . . . . . . . . . . . . . +201183
. . . 61 . . . . . . . . . . . . . . 176108
. . . 62 . . . . . . . . . . . . . . 176106
. . . 63 . . . . . . . . . . . . . +206602
. . . 64 . . . . . . . . . . . . . . 212286
. . . 65 . . . . . . . . . . . . . . 199849
. . . 66 . . . . . . . . . . . . . . 071731
. . . 67 . . . . . . . . . . . . . . 191812
. . . 68 . . . . . . . . . . . . . . 071890
. . . 69 . . . . . . . . . . . . . . 071730
. . . 70 . . . . . . . . . . . . . . 083476
. . . 71 . . . . . . . . . . . . . . 135205
. . . . . . . . . . . . . . . . . . . . 199505
. . . 72 . . . . . . . . . . . . . . 165271
. . . 73 . . . . . . . . . . . . . . 176529
. . . 74 . . . . . . . . . . . . . . 113854
. . . 75 . . . . . . . . . . . . . . 176528
. . . 76 . . . . . . . . . . . . . . 173336
. . . 77 . . . . . . . . . . . . . . 066298
. . . 78 . . . . . . . . . . . . . . 218003
. . . 79 . . . . . . . . . . . . . . 206297
. . . 80 . . . . . . . . . . . . . *192744
. . . . . . . . . . . . . . . . . . . . 199383
. . . . . . . . . . . . . . . . . . . . 191819
. . Engine, Deutz Dsl Elec Bf4m2011 (includes) . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Adapter, Engine Deutz 1011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Flywheel, Deutz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Sender, Coolant Temp & 130c Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Switch, Pressure Oil 1.5 Bar Nc Cont . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Secondary Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Spacer, Stl .323 Id X .625 Od X .141 Thk (Alternator) . . . . . . . . . . . . . . . . 1
. . Sender, Pressure Oil 0− 100 Psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Adaptor, Oil Pressure Sender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Glow Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Fan, Engine Cooling 18.000 Suction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Spacer, Stl .800id X 1.188od X .090 Thk (Fan Hub Bolt) . . . . . . . . . . . . . . 1
. . Belt, V .375 X 45.125 Lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Extension, Hydraulic 37 Deg Flare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Hose, Tubing Oil Assyw/Fittings 27.040lg . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Ftg, Stl Adapter 3/4 Sae−3/4 Jic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Guard, Fan LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Shroud, Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Cooler, Oil Engine/Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Ftg, Brs Adapter Long 3/4 Sae−3/4 Jic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Upright, Rear Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Bolt, J Stl .312−18 X 7.750 Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . Battery, Stor 12v 650 Crk 110 Rsv Gp 24 Maint Free . . . . . . . . . . . . . . . . 1
. . Terminal Protector, Battery Post Mtg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . Cable, Bat Neg 42 In Lg 2 Awg W/Clamp & .375 Rng . . . . . . . . . . . . . . . . 1
. . Cable, Bat Pos 45 In Lg No 1 Awg W/Clamp & .406 Rng . . . . . . . . . . . . . 1
. . Bracket, Battery Holddown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Cover, Battery Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Label, Warning Battery Explosion Can Blind . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Label, Warning Moving Parts Can Cause Serious . . . . . . . . . . . . . . . . . . . 8
. . Panel, Engine Extension R.H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Guard, Fan RH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Screw, 625−11x4.00 Hex Hd−pln Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . Washer, Flat .656idx2.250odx.187t Stl Pld . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . Bracket, Mtg Engine R.h. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Retainer, Mount Eng/Gen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . Tubing, Stl .875 Od X12ga Wall X 2.500 . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . Mount, Eng/Gen Nprn .875id X 2.500od X 2.000 60 Dur . . . . . . . . . . . . . . 4
. . Nut, 625−11 .94hex .77h Stl Pld Elastic Stop Nut . . . . . . . . . . . . . . . . . . . 4
. . Hose Assy, Oil Drain 32.000 Lg (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Valve, Oil Drain 3/8−18 Nptf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Ftg, Hose Brs Barbed Fem 1/2 Tbg X 3/8 Npt . . . . . . . . . . . . . . . . . . . . . 1
. . . . Hose, Sae .500 Id X .780 Od Xcoil . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.666
. . Ftg, Hose Brs Barbed Elbow M 1/2 Tbg X 1/2 Npt . . . . . . . . . . . . . . . . . . . 1
. . Ftg, Adapter Oil Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Ring (Oil Drain) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Bracket, Mtg Fuel Filter/Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Base, Fuel Filter Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Filter, Fuel Spin−on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Hose, Sae .312 Id X .560 Od X 8.000 (Fuel Filter To Fuel Pump) . . . . . . 1
. . Hose, Sae .312 Id X .560 Od X 14.000 (Fuel Tank To Fuel Filter) . . . . . . 1
OM-4420 Page 61
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 15-1. Main Assembly (Continued)
. . . 81 . . . . . . . . . . . . . . 174064
. . . . . . . . . . . . . . . . . . . . 196036
. . . . . . . . . . . . . . . . . . . . 125663
. . . . . . . . . . . . . . . . . . . . 175936
. . . . . . . . . . . . . . . . . . . . 127994
. . . . . . . . . . . . . . . . . . . . 127648
. . . . . . . . . . . . . . . . . . . . 124974
. . . . . . . . . . . . . . . . . . . . 601868
. . . . . . . . . . . . . . . . . . . . 126388
. . . . . . . . . . . . . . . . . . . . 089800
. . . . . . . . . . . . . . . . . . . . 108941
. . . . . . . . . . . . . . . . . . . . 156733
. . . 82 . . . . . . . . . . . . . . 190992
. . . 83 . . . . . . . . . . . . . . 085963
. . . 84 . . . . . . . . . . . . . . 206604
. . . 85 . . . . . . . . . . . . . . 199592
. . . 86 . . . . . . . . . . . . +200 989
. . . 87 . . . . . . . . . . . . . . 206464
. . . 88 . . . . . . . . . . . . . 189 975
. . . 89 . . . . . . . . . . . . . 208 141
. . . 90 . . . . . . . . . . . . . 189 826
. . . 91 . . . . . . . . . . . . . . 191626
. . . 92 . . . . . . . . . . . . . +189827
. . . 93 . . . . . . . . . . Figure 15-4
. . . 94 . . . . . . . . . . . . . . 218087
. . . 95 . . . . . . . . . . . . . . 124253
. . . 96 . . . . . . . . . . . . . . 189912
. . . 97 . . . . . . . . . . . . . . 189909
. . . 98 . . . . . . . . . . . . . . 189913
. . . 99 . . . . . . . . . . . . . . 190142
. . 100 . . . . . . . . . . . . . 189910
. . 101 . . . . . . . . . . . . . 189908
. . 102 . . . . . . . . . . . . . 181572
. . . . . . . . . . . . . . . . . . . . 196219
. . 103 . . . . . . . . . . . . . 191446
. . 104 . . . . . . . . . . . . . 209094
. . 105 . . . . . . . . . . . . +212224
. . 106 . . . . . . . . . . . . . 191897
. . 107 . . . . . . . . . . . . . 200864
. . 108 . . . . . . . . . . . . . 212046
. . 109 . . . . R3 . . . . . 189699
. . 110 . . . . . . . . . . . . . 218086
. . 111 . . . . . . . . . Figure 15-2
. . 112 . . . . . . . . . . . . . 189731
. . 113 . . . . . . . . . . . . . 203260
. . 114 . . . . . . . . . . . . . 191448
. . 115 . . . . . . . . . . . . . 201750
. . 116 . . . . . . . . . . . . . 182761
. . 117 . . . . . . . . . Figure 15-3
. . 118 . . . CT1 . . ♦202130
. . 119 . . . . . . . . . Figure 15-5
. . 120 . . . . . . . . . . . . . 193453
. . 121 . . . PC1 . . . . 207397
. . 122 . . . . . . . . . . . . . 208024
. . 123 . . . . . . . . . . . . . 206613
. . 124 . . . . . . . . . . . . . 213896
. . 125 . . . . . . . . . . . . . 105734
OM-4420 Page 62
. . Idle, Solenoid Assy (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Bracket, Arm Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Ball Joint, .250−28 Type Sp Lh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Rod, Throttle 5.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Ball Joint, .250−28 Type Spf Female Rod End . . . . . . . . . . . . . . . . . . . .
. . . . Clevis, Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Solenoid, 12vdc Pull/Hold Type 1” Stroke . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Nut, 250−28 .44hex .26h Stl Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Nut, 250−28 .44hex .27h Stl Pld Lh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Nut, 250−20 .44hex .22h Stl Pld .58d Flange Defor . . . . . . . . . . . . . . . .
. . . . Screw, 250−20x1.00 Hexwhd.61d Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Nut, 250−28 .44hex .13h Stl Pld Sem Cone Wshr.51d . . . . . . . . . . . . . .
. . Keeper, latch engine access door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Spring, Ext .375 Od X .041 Wire X 2.000 (ForSafety Latch) . . . . . . . . . . .
. . Channel, stiffener engine access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Latch, paddle series 20 (black) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Door, engine access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Hinge, door access 180deg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Stop, door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Panel, rocker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bumper, Door Engine Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Panel, Gen Rh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Generator Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Tank, Fuel (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Bushing, Tank Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Ftg, Stl Barbed Elbow W/.047in Orifice Zinc Pld . . . . . . . . . . . . . . . . . . .
. . . . Ftg, Stand Pipe Hose .250 X 9.265lg 90 Deg Zinc . . . . . . . . . . . . . . . . .
. . . . Ftg, Stl Barbed Elbow Zinc Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Sender, Fuel Gauge 9.750 Deep Tank . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Ftg, Stand Pipe Hose .3125 X 9.260lg 90 Deg Zinc . . . . . . . . . . . . . . . .
. . . . Valve, Drain Fuel 180 Deg Zinc Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Bushing, Tank Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Hose, Sae .250 Id X .500 Od X 26.000 (Fuel Return Line) . . . . . . . . . . . .
. . Extrusion, Rubber w/Adhesive 1.000 x 1.000 (order by ft.) . . . . . . . . . . . .
. . Bracket, Mtg Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Do Not Weld On Base CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Manufacturing Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Resistor, WW Tap 375 W 10 Ohm W/Mtg Bkt . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Holddown Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Firewall, Bottom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Caution Do Not Use Ether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Cover, Top Front Upright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Upright, Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Warning General Precautionary CSA . . . . . . . . . . . . . . . . . . . . . . . . .
. . Panel, Front w/components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Xfmr, Current Sensing (Auto Idle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Main Rectifier Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Box Fcr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Module, Field Current Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pulley, Fan Assy W/Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Fan/Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Spacer, Stl 1.250 X.375 .531 Hole Dia (Muffler) . . . . . . . . . . . . . . . . . . . . . .
. . Pipe, Muffler Extension Elbow 1.750 Od . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
2
1
4
1
1
1
4
1
1
1
1
1
1
1
1
6ft
1
1
4
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 15-1. Main Assembly (Continued)
. . . . . . . . . . . . . . . . . . . . 049525
. . . . . . . . . . . . . . . . . . . . 049525
. . . . . . . . . . . . . . . . . . . . 212045
. . . . . . . . . . . . . . . . . . . ♦195118
. . . . . . . . . . . . . . . . . . ♦209238
. . . . . . . . . . . . . . . . . . ♦209240
. . . . . . . . . . . . . . . . . . ♦209236
. . . . . . . . . . . . . . . . . . ♦209241
. . . . . . . . . . . . . . . . . . ♦209242
. . . . . . . . . . . . . . . . . . ♦189975
. . . . . . . . . . . . . . . . . . ♦155146
+
*
. . Nut, 312−18 U−nut Multi−thread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Nut, 312−18 U−nut Multi−thread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Kit, Label (Includes Safety And Informational Labels) . . . . . . . . . . . . . . . . .
. . Kit, Lock-Out Vandalism (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Door, Access Rh W/Om Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Door, Access Lh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Tab, Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Mount, Access Rh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Mount, Access Lh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Hinge, Door Access 180 Deg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Sponge, Nprn .060 X 1.000 Wide X 4.000 Sce 41 Close . . . . . . . . . . . .
4
4
1
1
1
1
1
1
1
4
3
When ordering a component originally displaying a precautionary label, the label should also be ordered. Order
label individually or as part of Label Kit 212 045.
Recommended Spare Parts.
♦Optional
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
10
5
11
21
4
20
3
19
1
14
2
17
7
6
19
22
15
16
12
8
18
9
13
803 456-A
Figure 15-2. Control Box Assembly
OM-4420 Page 63
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 15-2. Control Box Assembly − (Figure 15-1 Item 111)
. . . 1 . . . F1, F2 . . . 085874 . . Fuse, Mintr Cer Slo−blo 10. Amp 250 Volt . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 2 . . . . . . . . . . . . . . 046432 . . Holder, Fuse Mintr .250 X 1.250 Panel Mtg . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 3 . . . . . . . . . . . . . . 134201 . . Stand−off Support, Pc Card .312/.375w/Post&lock .43 . . . . . . . . . . . . . . .
. . . 4 . . . . PC9 . . . . 192224 . . Circuit Card Assy, Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 5 . . . . . . . . . . . . . . 201077 . . Control Box, LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 206736 . . Harness, Control Box, Weld Control LH (includes) . . . . . . . . . . . . . . . . . . .
. . . 6 . CB11, CB12,CB13 139266 . . . . Circuit Breaker, Man Reset 1p 15a 250vac Frict . . . . . . . . . . . . . . . . . . .
. . . 7 . . . . SR1 . . . . 035704 . . . . Rectifier, Integ Bridge 40. Amp 800v . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . RC3 . . . . 158466 . . . . Conn, Rect Univ 084 12p/S 3row Rcpt Cable/Panel Lkg . . . . . . . . . . . .
. . . . . . . . . . RC1 . . . . 135133 . . . . Conn, Rect Univ 084 9p/S 3row Rcpt Cable/Panel Lkg . . . . . . . . . . . . .
. . . 8 . . . . . C9 . . . . . 087110 . . Capacitor, Elctlt 240 Uf 200 Vdc Can 1.39 Di . . . . . . . . . . . . . . . . . . . . . . .
. . . 9 . . . . . . . . . . . . . . 177136 . . Clamp, Capacitor 1.375 Dia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 204737 . . Cable Tie Mount, Winged Push . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 10 . . . . . . . . . . . . . . 201078 . . Control Box, Rh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 11 . . CR3, CR6 . . 090104 . . Relay, Encl 12vdc Spst 30a/15vdc 5pin Flange Mtg . . . . . . . . . . . . . . . . . .
. . . 12 . . . . PC7 . . . . 195706 . . Module, Pull To Idle, Two Output, 7 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 13 . . . . TD1 . . . . 214928 . . Timer, Delay On Make/Break Open 30 Sec 12vdc . . . . . . . . . . . . . . . . . . .
. . . 14 . . . . . . . . . . . . . +201079 . . Cover, Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 15 . . . . . . . . . . . . . . 217823 . . Label, Layout Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 217815 . . Harness, Engine Deutz Bf4m2011 (includes) . . . . . . . . . . . . . . . . . . . . . . . .
. . . 16 . . . . CB10 . . . . 190374 . . . . Circuit Breaker, Auto Reset 12vdc 40 Amp . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 156734 . . . . Nut, 010−32 .31hex .13h Stl Pld Sem Cone Wshr.38d . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 148850 . . . . Socket, Relay 5 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 17 . . . . CB14 . . . . 205927 . . . . Circuit Breaker, Auto Reset 12vdc 12 Amp . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . S2 . . . . . 021467 . . . . Switch,Tgl Spst 3a 250v Off−none−(On) Spd Term
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Located On Front Panel, See Figure 15-3) . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 211292 . . . . Conn, Pack 4p 1row Female (For Ignition Switch S1) . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 211293 . . . . Conn, Pack Terminal Position Assurance(Lock) . . . . . . . . . . . . . . . . . . . .
. . . 18 . . CR4,CR10 . 113247 . . . . Relay, Encl 12vdc Dpdt 20a/120vac 8pin Flange Mtg . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 150316 . . . . Conn, Rect Univ 039 6p/S 3row Plug Cable Lkg . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 164617 . . . . Clip,Wiring Straight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 19 . . C1/D1,C8/D8 . 189701 . . . . Diode/Capacitor Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
3
1
1
1
3
1
1
1
1
1
3
1
2
1
1
1
1
1
1
4
5
1
1
1
1
2
5
2
4
C10/D10, C14/D14
. . . 20 . . . . CR1 . . . . 214876 . . . . Relay, Encl 6 vdc spst 35A/14 vdc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 21 . . . . CR8 . . . . 197325 . . Relay, Encl 12vdc Spst 70a 4pin Flange Mtg . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 22 . . . . CR5 . . . . 199999 . . Relay, Encl 12vdc Dpst−no 30a 6pin Flange . . . . . . . . . . . . . . . . . . . . . . . . . 1
♦Optional
*Recommended Spare Parts.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-4420 Page 64
Hardware is common and
not available unless listed.
4
3
2
5
1
6
10
7
8
9
47
11
46
13
12
45
14
15
44
16
17
43
42
41
22
34
40
39
38
36
35
20
19
24
25
37
21
18
23
26
27
28
33
32
31
30
29
803 457
Figure 15-3. Panel, Front w/Components
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 15-3. Panel, Front w/Components (Figure 15-1 Item 117)
...
...
...
...
1
2
3
4
. . . . . . . . . . . . . . 217638
. . . . . . . . . . . . . . 215014
. . . . CT3 . . ♦209274
. . . . . S3 . . . . . 208278
..
..
..
..
Plate, Screened Ident Control (Order By Model And Serial Number) . . . .
Panel, Engine/Weld Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Xfmr, Current (Meters) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch, Range/Changeover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
OM-4420 Page 65
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 15-3. Panel, Front w/Components (Continued)
. . . . . . . . . . . . . . . . . . . . 192558 . . Harness, Range Switch (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . RC6 . . . . 148389 . . . . Conn, Rect Univ 084 4p/S 1row Rcpt Cable/Panel Lkg . . . . . . . . . . . . .
. . . 5 . . . . . R1 . . . . . 193118 . . Pot, Cp Flat 1t 2. W 1k Ohm Linear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 206809 . . Harness, Weld Control (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 6 . . . . . S6 . . . . . 193234 . . . . Switch, Rotary 6 Position Gold Contacts . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 197527 . . . . Guard, Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 7 . . . . . S5 . . . . . 011609 . . . . Switch, Tgl Spdt 15a 125vac On−none−on Spd Term Chr . . . . . . . . . . .
. . . . . . . . . . PLG9 . . . . 193183 . . . . Conn, Rect Cinch 18 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 196603 . . . . Seal, Switch 6 Position Rotary .250 Shaft . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . PLG14 . . . 141450 . . . . Conn, Rect Metrmate 10skt 1row Plug Cable Lkg . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 164617 . . . . Clip,Wiring Straight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . PLG10 . . . 150316 . . . . Conn, Rect Univ 039 6p/S 3row Plug Cable Lkg . . . . . . . . . . . . . . . . . . .
. . . 8 . . . . CB5 . . . . 139266 . . . . Circuit Breaker, Man Reset 1p 15a 250vac Frict . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . CB6 . . . . 139266 . . . . Circuit Breaker, Man Reset 1p 15a 250vac Frict . . . . . . . . . . . . . . . . . . .
. . . 9 . . . . . . . . . . . . . . 202209 . . Spacer, Nylon .221 Thk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 10 . . . . PC6 . . . . 192995 . . Circuit Card Assy, Connector/Receptacle . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 11 . . . . . S1 . . . . . 212436 . . Switch, Ignition 4 Position W/Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 12 . . . . . S2 . . . . . 021467 . . Switch,Tgl Spst 3a 250v Off−none−(On) Spd Term (Included In Engine
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wiring Harness, See Figure Figure 15-2) . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 13 . . . . CB1 . . . . 201083 . . Circuit Breaker, Man Reset 2p 20a 250vac . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 201553 . . Clip, Retaining Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 201109 . . Harness, Receptacle Auxillary Power (includes) . . . . . . . . . . . . . . . . . . . . .
. . . 14 . . . . CB2 . . . . 093996 . . . . Circuit Breaker, Man Reset 1p 20a 250vac Frict . . . . . . . . . . . . . . . . . . .
. . . 15 . . . GFCI1 . . . 151981 . . . . Rcpt, Str Dx Grd 2p3w 15/20a 125v *5−20r Gfi . . . . . . . . . . . . . . . . . . . .
. . . 16 . . . . RC1 . . . . 147632 . . . . Rcpt,Tw Lk Grd 2p3w 30a 250v *L6−30r . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 010146 . . . . Clamp, Nyl .625 Clamp Dia X.500 Wide .203 Mtg Hole . . . . . . . . . . . . .
. . . 17 . . . . . . . . . . . . . +215347 . . Panel, Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 18 . . . . . . . . . . . . . . 601836 . . Nut, 250−20 .50hex .19h Brs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 19 . . . . . . . . . . . . . . 010915 . . Washer, Flat .257idx0.640odx.031t Brs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 20 . . . . . . . . . . . . . . 163167 . . Washer, Lock .254idx0.489odx.062t Sst Split.250 . . . . . . . . . . . . . . . . . . .
. . . 21 . . . . GRD . . . . 083030 . . Stud, Brs .250−20 X 1.750 W/Hex Collar . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 22 . . . . . . . . . . . . . . 200910 . . Label, Warning Electric Shock And Moving Parts Ce . . . . . . . . . . . . . . . . .
. . . 23 . . . . . . . . . . . . . . 209056 . . Cover, Receptacle 2.250 Dia. Lexan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 24 . . . . . . . . . . . . . . 201125 . . Panel, Mtg Terminal Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 25 . . . . . . . . . . . . . . 039047 . . Terminal, Pwr Output Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 26 . . PC4, PC5 . . 189744 . . Circuit Card Assembly, HF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 27 . . . . . S12 . . ♦220491 . . Switch, Polarity/AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 28 . . . . . . . . . . . . . . 039046 . . Terminal, Pwr Output Black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 180735 . . Washer, Output Stud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 29 . . . . . . . . . . . . . . 134201 . . Stand−off Support, Pc Card .312/.375w/Post&lock .43 . . . . . . . . . . . . . . .
. . . 30 . . . . . . . . . . . . . . 181169 . . Spacer, Output Stud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 31 . . . . . . . . . . . . . . 186621 . . Boot, Generic Output Stud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 32 . . . . . . . . . . . . ♦059773 . . Handle, Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 33 . . . . . . . . . . . . ♦010647 . . Pin, Spring Cs .156 X 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 34 . . . . . . . . . . . . . . 021385 . . Boot, Toggle Switch Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 35 . . . . . . . . . . . . . . 190323 . . Boot, Circuit Breaker Clear Hex Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 36 . . . . . . . . . . . . . . 170391 . . Conn, Circ Ms Protective Cap Size 20 Nylon . . . . . . . . . . . . . . . . . . . . . . .
. . . 37 . . . . HM1 . . . . 210424 . . Meter, Hour 12−24vdc (Snap−in) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 38 . . . . FUEL . . . . 192265 . . Gauge, Fuel Elec Switch W/O Switchgage Sensor . . . . . . . . . . . . . . . . . .
. . . 39 . . . . BAT . . . . 193228 . . Meter, Volt DC 8 − 18 Scale 2.250 In Black Face . . . . . . . . . . . . . . . . . . . .
. . . 40 . . . . TEMP . . . 217084 . . Gauge, Coolant Temp 0− 300 Deg F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 41 . . . . . OIL . . . . . 217083 . . Gauge, Pressure Oil 0−100 Psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 42 . . . . . A1 . . . ♦164873 . . Meter, Amp AC/DC 0− 500 0−600 Dc Scale 2.5 In . . . . . . . . . . . . . . . . . . .
. . . 43 . . . . . V1 . . . ♦164874 . . Meter, Volt AC/DC 0− 100 Scale 2.5 In . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 44 . . . . . . . . . . . . . . 097922 . . Knob, Pointer .875 Dia X .250 Id W/Set Screwsplstc . . . . . . . . . . . . . . . . .
. . . 45 . . . . . . . . . . . . . . 189161 . . Handle, Switch Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 46 . . . . . . . . . . . . . . 010647 . . Pin, Spring Cs .156 X 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-4420 Page 66
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
3
4
2
1
1
2
1
1
2
1
1
2
8
2
2
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 15-3. Panel, Front w/Components (Continued)
. . . 47 . . . . . . . . . . . . . .
....................
....................
. . . . . . . . . . PLG6 . . . .
. . . . . . . . . . PLG8 . . . .
....................
. . . . . . . . . PLG13 . . .
....................
....................
....................
....................
....................
....................
....................
....................
097924
072590
215207
114063
193184
147992
158465
088731
135873
187654
196602
059712
024103
120304
025234
. . Knob, Pointer 1.625 Dia X .250 Id W/Set Screwsplstc . . . . . . . . . . . . . . . .
. . Lock, Shaft Pot .375−32 X .250 Dia Shaft Tall . . . . . . . . . . . . . . . . . . . . . . .
. . Harness, Unit Weld Control − CV (includes) . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Conn, Rect Univ 084 4p/S 1row Plug Cable Lkg . . . . . . . . . . . . . . . . . . .
. . . . Conn, Rect Cinch 30 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Conn, Rect Univ 039 10p/S 2row Plug Cable Lkg . . . . . . . . . . . . . . . . . .
. . . . Conn, Rect Univ 084 12p/S 3row Plug Cable Lkg . . . . . . . . . . . . . . . . . .
. . . . Bushing, Snap−in Nyl .375 Id X .500 Mtg Hole . . . . . . . . . . . . . . . . . . . .
. . . . Clip, Conduit Convoluted 1/2 In 6.35mm Mtg Hole . . . . . . . . . . . . . . . . .
. . . . Seal, Wire Univ 12p/S 3row . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Plug, Cavity 18,30 Position Cinch Connector . . . . . . . . . . . . . . . . . . . . . .
. . Clip, Component .437 Dia Mtg Adh Back . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Blank, Snap−in Nyl .750 Mtg Hole Black . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Blank, Snap−in Nyl .250 Mtg Hole Black . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Plug, Str Grd 2p3w 15a 250v *6−15p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
3
1
7
1
1
2
1
♦Optional
+
When ordering a component originally displaying a precautionary label, the label should also be ordered. Order
label individually or as part of Label Kit 212 045
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
15
11
16
14
10
12
13
18
17
9
19
8
20
21
7
6
5
3
22
4
1
2
26
29
31
34
33
28
25
24
23
27
30
32
803 327
Figure 15-4. Generator
OM-4420 Page 67
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 15-4. Generator (Figure 15-1 Item 93)
. . . 1 . . . . . . . . . . . . . . 132053 . . Screw, 375−16x1.50 Hex Hd−pln Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 2 . . . . . . . . . . . . . . 183387 . . Washer, Cone .380idx .860odx.109t Stl Pld 4000lbs . . . . . . . . . . . . . . . . .
. . . 3 . . . . . . . . . . . . . . 195911 . . Endbell, Gen (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 4 . . . . . . . . . . . . . . 143220 . . . . O-Ring 2.859 ID X .139 Cs 70 Duro Viton . . . . . . . . . . . . . . . . . . . . . . . .
. . . 5 . AUX STATOR . 201099 . . Stator, Exciter/Aux Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 6 . . . STATOR . . +208287 . . Stator, Weld Assy Complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 7 . . . . . . . . . . . . . . 176106 . . Label, Warning Moving Parts Can Cause Serious . . . . . . . . . . . . . . . . . . .
. . . 8 . . . . . . . . . . . . . . 190197 . . Guard, Generator Wire Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 9 . . . . . . . . . . . . . . 172674 . . Spring, Ext .240 Od X .041 Wire X 3.500 Pld . . . . . . . . . . . . . . . . . . . . . . .
. . . 10 . . . . . . . . . . . . . . 039207 . . Baffle, Air Gen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 11 . . . ROTOR . . . 210446 . . Rotor, Generator (Includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 12 . . . . . . . . . . . . . . 024617 . . . . Ring, Rtng Ext 1.375 Shaft X .050 Thk . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 13 . . . . . . . . . . . . . . 053390 . . . . Bearing, Ball Rdl Sgl Row 1.370 X 2.830 X .6 . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 210447 . . . . Fan, Rotor Assy Generator (Segmented) (includes) . . . . . . . . . . . . . . .
. . . 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hub, Drive (Not Sold Separately) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 15 . . . . . . . . . . . . . . 210332 . . . . . . Plate, Flex Hubmount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 16 . . . . . . . . . . . . . . 206242 . . . . . . Fan, Rotor Segmented Assy Gen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 17 . . . . . . . . . . . . . . 049026 . . . . . . Screw, M10−1.5x 25 Hex Hd−pln 8.8 Pln . . . . . . . . . . . . . . . . . . . . . . . .
. . . 18 . . . . . . . . . . . . . . 083883 . . . . . . Washer, Lock .402idx0.709odx.087t Stl Split10mm . . . . . . . . . . . . . . .
. . . 19 . . . . . . . . . . . . . . 080389 . . . . . . Screw, 312−18x1.00 Hexwhd.66d Stl Pld Slffmg Tap−rw . . . . . . . . . .
. . . 20 . . . . . . . . . . . . . . 083883 . . Washer, Lock .402idx0.709odx.087t Stl Split10mm . . . . . . . . . . . . . . . . . .
. . . 21 . . . . . . . . . . . . . . 049026 . . Screw, M10−1.5x 25 Hex Hd−pln 8.8 Pln . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 22 . . . . . . . . . . . . . . 191579 . . Cover, Starter Hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 23 . . . . . . . . . . . . . . 083883 . . Washer, Lock .402idx0.709odx.087t Stl Split10mm . . . . . . . . . . . . . . . . . .
. . . 24 . . . . . . . . . . . . . . 172555 . . Screw, M10−1.5x 50 Hex Hd−pln 8.8 Pld . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 25 . . . . . . . . . . . . . . 602159 . . Screw, 312−18x .75 Hexwhd.66d Stl Pld Slffmg Tap−rw . . . . . . . . . . . . . .
. . . 26 . . . . . . . . . . . . . . 604950 . . Screw, 312−18x2.00 Hex Hd−pln Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 27 . . . . . . . . . . . . . . 602211 . . Washer, Lock .318idx0.586odx.078t Stl Pld Split.312 . . . . . . . . . . . . . . . .
. . . 28 . . . . . . . . . . . . . . 139341 . . Washer, Exciter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 29 . . . . . . . . . . . . . *190823 . . Brush, Contact Elect .250 X.500 X 1.250 Grd Ay . . . . . . . . . . . . . . . . . . . .
. . . 30 . . . . . . . . . . . . . . 188560 . . Clip, Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 31 . . . . . . . . . . . . . . 189142 . . Brushholder, Generator (Brushes Not Included − See Item 29) . . . . . . . .
. . . 32 . . . . . . . . . . . . . . 602242 . . Washer, Flat .375idx0.875odx.083t Stl Pld . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 33 . . . . . . . . . . . . . . 602211 . . Washer, Lock .318idx0.586odx.078t Stl Pld Split.312 . . . . . . . . . . . . . . . .
. . . 34 . . . . . . . . . . . . . . 604534 . . Screw, 312−18x1.25 Hex Hd−pln Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6
1
1
1
1
8
1
2
1
1
1
1
1
1
1
4
10
10
8
4
4
1
6
6
6
4
4
4
3
3
1
2
2
2
+
When ordering a component originally displaying a precautionary label, the label should also be ordered. Order
label individually or as part of Label Kit 212 045.
*Recommended Spare Parts.
♦Optional
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-4420 Page 68
Hardware is common and
not available unless listed.
4
3
2
1
5
6
7
8
9
802 279-A
Figure 15-5. Main Rectifier Assembly
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 15-5. Main Rectifier Assembly (Figure 15-1 Item 119)
. . . . . . . . . . SR3 . . . .
... 1 ..............
... 2 ..............
... 3 ..............
... 4 ..............
. . . 5 . . . . PC3 . . . .
... 6 ..............
... 7 ..............
. . . 8 . D3, D5, D7 .
. . . 9 . D2, D4, D6 .
215909
188137
188517
188135
134201
215755
188136
188493
037956
037957
. . Rectifier Complete (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Connection Board, Rectifier Ac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Bus Bar, Conn Bd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Enclosure, Rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Stand−off Support, Pc Card .312/.375w/Post&lock .43 . . . . . . . . . . . . .
. . . . Circuit Card Assy, Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Insulator, Heatsink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Heat Sink, Rectifier Al . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Diode, Rect 275. A 300v Sp Do−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Diode, Rect 275. A 300v Rp Do−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
3
2
3
1
8
2
3
3
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-4420 Page 69
Effective January 1, 2004
(Equipment with a serial number preface of “LE” or newer)
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
Warranty Questions?
Call
1-800-4-A-MILLER
for your local
Miller distributor.
Your distributor also gives
you ...
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
LIMITED WARRANTY − Subject to the terms and conditions
below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to
its original retail purchaser that new Miller equipment sold after
the effective date of this limited warranty is free of defects in
material and workmanship at the time it is shipped by Miller.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
*
Induction Heating Coils and Blankets
*
APT & SAF Model Plasma Cutting Torches
*
Remote Controls
*
Accessory Kits
*
Replacement Parts (No labor)
*
Spoolmate Spoolguns
*
Canvas Covers
Within the warranty periods listed below, Miller will repair or
replace any warranted parts or components that fail due to such
defects in material or workmanship. Miller must be notified in
writing within thirty (30) days of such defect or failure, at which
time Miller will provide instructions on the warranty claim
procedures to be followed.
Miller’s True Blue Limited Warranty shall not apply to:
1.
Miller shall honor warranty claims on warranted equipment
listed below in the event of such a failure within the warranty
time periods. All warranty time periods start on the date that the
equipment was delivered to the original retail purchaser, or one
year after the equipment is sent to a North American distributor
or eighteen months after the equipment is sent to an
International distributor.
Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, slip rings,
relays or parts that fail due to normal wear. (Exception:
brushes, slip rings, and relays are covered on Bobcat,
Trailblazer, and Legend models.)
2.
Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.
3.
Equipment that has been modified by any party other than
Miller, or equipment that has been improperly installed,
improperly operated or misused based upon industry
standards, or equipment which has not had reasonable
and necessary maintenance, or equipment which has
been used for operation outside of the specifications for the
equipment.
1.
5 Years Parts — 3 Years Labor
*
*
2.
3 Years — Parts and Labor
*
*
*
*
3.
Original main power rectifiers
Inverters (input and output rectifiers only)
Transformer/Rectifier Power Sources
Plasma Arc Cutting Power Sources
Semi-Automatic and Automatic Wire Feeders
Inverter Power Sources (Unless Otherwise Stated)
*
Water Coolant Systems (Integrated)
*
*
*
Intellitig
Maxstar 150
Engine Driven Welding Generators
(NOTE: Engines are warranted separately by
the engine manufacturer.)
1 Year — Parts and Labor Unless Specified
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
DS-2 Wire Feeder
Motor Driven Guns (w/exception of Spoolmate
Spoolguns)
Process Controllers
Positioners and Controllers
Automatic Motion Devices
RFCS Foot Controls
Induction Heating Power Sources and Coolers
Water Coolant Systems (Non-Integrated)
Flowgauge and Flowmeter Regulators (No Labor)
HF Units
Grids
Maxstar 85, 140
Spot Welders
Load Banks
Arc Stud Power Sources & Arc Stud Guns
Racks
Running Gear/Trailers
Plasma Cutting Torches (except APT & SAF
Models)
Field Options
(NOTE: Field options are covered under True
Blue for the remaining warranty period of the
product they are installed in, or for a minimum of
one year — whichever is greater.)
4.
6 Months — Batteries
5.
90 Days — Parts
*
MIG Guns/TIG Torches
MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND
PERSONS TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4)
payment of or credit for the purchase price (less reasonable
depreciation based upon actual use) upon return of the goods at
customer’s risk and expense. Miller’s option of repair or
replacement will be F.O.B., Factory at Appleton, Wisconsin, or
F.O.B. at a Miller authorized service facility as determined by
Miller. Therefore no compensation or reimbursement for
transportation costs of any kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT,
INDIRECT,
SPECIAL,
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR
ANY OTHER LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND
ANY
IMPLIED
WARRANTY,
GUARANTY
OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS
PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION
OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING,
INCLUDING
ANY
IMPLIED
WARRANTY
OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT
FURNISHED BY MILLER IS EXCLUDED AND DISCLAIMED
BY MILLER.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary
from state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein,
and to the extent that they may not be waived, the limitations
and exclusions set out above may not apply. This Limited
Warranty provides specific legal rights, and other rights may be
available, but may vary from province to province.
miller_warr 6/04
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
For Service
Contact a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
Replacement Parts
Training (Schools, Videos, Books)
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
Welding Process Handbooks
To locate a Distributor or Service Agency visit
www.millerwelds.com or call 1-800-4-A-Miller
Contact the Delivering Carrier to:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.
PRINTED IN USA
 2004 Miller Electric Mfg. Co. 10/04
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
International Headquarters−USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
European Headquarters −
United Kingdom
Phone: 44 (0) 1204-593493
FAX: 44 (0) 1204-598066
www.MillerWelds.com