Miller | LG172350W | Owner Manual | Miller DS-74DX SWINGARC User manual

Miller DS-74DX SWINGARC User manual
OM-1500-14
207 499G
2006−05
Processes
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
(Gas-and Self-Shielding)
Submerged (SAW) Welding
Description
Wire Feeder
(Use with CV Power Sources)
DS-74DX Swingarc
™
DS-74DX12, and DS-74DX16
File: MIG (GMAW)
Visit our website at
www.MillerWelds.com
From Miller to You
Thank you and congratulations on choosing Miller. Now you can get
the job done and get it done right. We know you don’t have time to do
it any other way.
That’s why when Niels Miller first started building arc welders in 1929,
he made sure his products offered long-lasting value and superior
quality. Like you, his customers couldn’t afford anything less. Miller
products had to be more than the best they could be. They had to be the
best you could buy.
Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.
This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.
We’ve made installation and operation quick
and easy. With Miller you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will
help you figure out what the problem is. The
Miller is the first welding parts list will then help you to decide the
equipment manufacturer in exact part you may need to fix the problem.
the U.S.A. to be registered to
the ISO 9001:2000 Quality Warranty and service information for your
System Standard.
particular model are also provided.
Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor to receive the latest full
line catalog or individual specification sheets. To locate your nearest
distributor or service agency call 1-800-4-A-Miller, or visit us at
www.MillerWelds.com on the web.
Mil_Thank 4/05
Working as hard as you do
− every power source from
Miller is backed by the most
hassle-free warranty in the
business.
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − CONSIGNES DE SÉCURITÉ − À LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Signification des symboles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Dangers relatifs au soudage à l’arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Autres symboles relatifs à l’installation, au fonctionnement et à l’entretien de l’appareil. . . . . . . . . . . .
2-4. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Information sur les champs électromagnétiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Installing Swivel Into Pipe Post . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Installing Control Box And Adjusting Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Installing Boom And Reel Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Installing Wire Guide Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5. Equipment Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6. Control Box Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7. 14-Pin Plug Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8. Removing Safety Collar And Adjusting Boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-9. Gun Recommendation Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10. Wire Type, Size, And Feed Speed Capability Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-11. Installing And Threading Welding Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-12. Setting Internal DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-13. Power Source Selection Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Operational Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. Left/Right Select Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4. Jog/Purge Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-5. Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6. Program Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-7. Upper Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-8. Lower Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-9. Setup Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-10. Adjust Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-11. Sequence Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-12. Auxiliary Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − SETTING SEQUENCE PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1. Sequence Parameters In A Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − SETTING DUAL SCHEDULE PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1. Optional Dual Schedule Switch Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2. Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3. Diagnostics For User Defined Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 8 − MAINTENANCE & TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-2. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9 − ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 10 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPTIONS AND ACCESSORIES
WARRANTY
1
1
1
3
3
4
4
5
5
5
7
8
8
9
9
9
9
10
10
11
12
13
13
14
14
14
15
16
17
18
18
18
18
19
19
20
20
21
21
22
22
23
25
25
26
26
27
28
28
28
29
30
32
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
som _3/05
Y Warning: Protect yourself and others from injury — read and follow these precautions.
1-1. Symbol Usage
Means Warning! Watch Out! There are possible hazards
with this procedure! The possible hazards are shown in
the adjoining symbols.
Y Marks a special safety message.
. Means “Note”; not safety related.
This group of symbols means Warning! Watch Out! possible
ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.
Consult symbols and related instructions below for necessary actions
to avoid the hazards.
1-2. Arc Welding Hazards
Y The symbols shown below are used throughout this manual to
call attention to and identify possible hazards. When you see
the symbol, watch out, and follow the related instructions to
avoid the hazard. The safety information given below is only
a summary of the more complete safety information found in
the Safety Standards listed in Section 1-5. Read and follow all
Safety Standards.
Y Only qualified persons should install, operate, maintain, and
repair this unit.
D
D
D
D
D
D
Y During operation, keep everybody, especially children, away.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic wire welding, the
wire, wire reel, drive roll housing, and all metal parts touching the
welding wire are electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.
D Do not touch live electrical parts.
D Wear dry, hole-free insulating gloves and body protection.
D Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
D Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
D Use AC output ONLY if required for the welding process.
D If AC output is required, use remote output control if present on
unit.
D Additional safety precautions are required when any of the following electrically hazardous conditions are present: in damp
locations or while wearing wet clothing; on metal structures such
as floors, gratings, or scaffolds; when in cramped positions such
as sitting, kneeling, or lying; or when there is a high risk of unavoidable or accidental contact with the workpiece or ground. For these
conditions, use the following equipment in order presented: 1) a
semiautomatic DC constant voltage (wire) welder, 2) a DC manual
(stick) welder, or 3) an AC welder with reduced open-circuit voltage. In most situations, use of a DC, constant voltage wire welder
is recommended. And, do not work alone!
D Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
D Properly install and ground this equipment according to its
Owner’s Manual and national, state, and local codes.
D Always verify the supply ground − check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.
D When making input connections, attach proper grounding conductor first − double-check connections.
D Frequently inspect input power cord for damage or bare wiring −
replace cord immediately if damaged − bare wiring can kill.
D
D
D
D
D
D
Turn off all equipment when not in use.
Do not use worn, damaged, undersized, or poorly spliced cables.
Do not drape cables over your body.
If earth grounding of the workpiece is required, ground it directly
with a separate cable.
Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
Do not touch electrode holders connected to two welding machines at the same time since double open-circuit voltage will be
present.
Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
Wear a safety harness if working above floor level.
Keep all panels and covers securely in place.
Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
Do not connect more than one electrode or work cable to any
single weld output terminal.
SIGNIFICANT DC VOLTAGE exists in inverter-type
welding power sources after removal of input
power.
D Turn Off inverter, disconnect input power, and discharge input
capacitors according to instructions in Maintenance Section
before touching any parts.
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
D Keep your head out of the fumes. Do not breathe the fumes.
D If inside, ventilate the area and/or use local forced ventilation at the
arc to remove welding fumes and gases.
D If ventilation is poor, wear an approved air-supplied respirator.
D Read and understand the Material Safety Data Sheets (MSDSs)
and the manufacturer’s instructions for metals, consumables,
coatings, cleaners, and degreasers.
D Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watchperson nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breathing air is safe.
D Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
D Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and while wearing an air-supplied
respirator. The coatings and any metals containing these elements
can give off toxic fumes if welded.
OM-1500-14 Page 1
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
D Wear an approved welding helmet fitted with a proper shade of filter lenses to protect your face and eyes when welding or watching
(see ANSI Z49.1 and Z87.1 listed in Safety Standards).
D Wear approved safety glasses with side shields under your
helmet.
D Use protective screens or barriers to protect others from flash,
glare and sparks; warn others not to watch the arc.
D Wear protective clothing made from durable, flame-resistant material (leather, heavy cotton, or wool) and foot protection.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.
D Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
D Do not weld where flying sparks can strike flammable material.
D Protect yourself and others from flying sparks and hot metal.
D Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
D Watch for fire, and keep a fire extinguisher nearby.
D Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
D Do not weld on closed containers such as tanks, drums, or pipes,
unless they are properly prepared according to AWS F4.1 (see
Safety Standards).
D Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock, sparks, and fire
hazards.
D Do not use welder to thaw frozen pipes.
D Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
D Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
D Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
D Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B
for hot work and have a fire watcher and extinguisher nearby.
FLYING METAL can injure eyes.
D Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
D Wear approved safety glasses with side
shields even under your welding helmet.
OM-1500-14 Page 2
BUILDUP OF GAS can injure or kill.
D Shut off shielding gas supply when not in use.
D Always ventilate confined spaces or use
approved air-supplied respirator.
HOT PARTS can cause severe burns.
D Do not touch hot parts bare handed.
D Allow cooling period before working on gun or
torch.
D To handle hot parts, use proper tools and/or
wear heavy, insulated welding gloves and
clothing to prevent burns.
MAGNETIC FIELDS can affect pacemakers.
D Pacemaker wearers keep away.
D Wearers should consult their doctor before
going near arc welding, gouging, or spot
welding operations.
NOISE can damage hearing.
Noise from some processes or equipment can
damage hearing.
D Wear approved ear protection if noise level is
high.
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
D Protect compressed gas cylinders from excessive heat, mechanical shocks, physical damage, slag, open flames, sparks, and arcs.
D Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
D Keep cylinders away from any welding or other electrical circuits.
D Never drape a welding torch over a gas cylinder.
D Never allow a welding electrode to touch any cylinder.
D Never weld on a pressurized cylinder − explosion will result.
D Use only correct shielding gas cylinders, regulators, hoses, and fittings designed for the specific application; maintain them and
associated parts in good condition.
D Turn face away from valve outlet when opening cylinder valve.
D Keep protective cap in place over valve except when cylinder is in
use or connected for use.
D Use the right equipment, correct procedures, and sufficient number of persons to lift and move cylinders.
D Read and follow instructions on compressed gas cylinders,
associated equipment, and Compressed Gas Association (CGA)
publication P-1 listed in Safety Standards.
1-3. Additional Symbols For Installation, Operation, And Maintenance
FIRE OR EXPLOSION hazard.
MOVING PARTS can cause injury.
D Do not install or place unit on, over, or near
combustible surfaces.
D Do not install unit near flammables.
D Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
D Keep away from moving parts such as fans.
D Keep all doors, panels, covers, and guards
closed and securely in place.
D Have only qualified persons remove doors,
panels, covers, or guards for maintenance as
necessary.
D Reinstall doors, panels, covers, or guards
when maintenance is finished and before reconnecting input power.
FALLING UNIT can cause injury.
D Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
D Use equipment of adequate capacity to lift and
support unit.
D If using lift forks to move unit, be sure forks are
long enough to extend beyond opposite side of
unit.
READ INSTRUCTIONS.
D Read Owner’s Manual before using or servicing unit.
D Use only genuine Miller/Hobart replacement
parts.
H.F. RADIATION can cause interference.
OVERUSE can cause OVERHEATING
D Allow cooling period; follow rated duty cycle.
D Reduce current or reduce duty cycle before
starting to weld again.
D Do not block or filter airflow to unit.
D
D
STATIC (ESD) can damage PC boards.
D Put on grounded wrist strap BEFORE handling
boards or parts.
D Use proper static-proof bags and boxes to
store, move, or ship PC boards.
D
D
D High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
D Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
ARC WELDING can cause interference.
MOVING PARTS can cause injury.
D Keep away from moving parts.
D Keep away from pinch points such as drive
rolls.
D
WELDING WIRE can cause injury.
D Do not press gun trigger until instructed to do
so.
D Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
D
D
D
D Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
D Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
1-4. California Proposition 65 Warnings
Y Welding or cutting equipment produces fumes or gases which
contain chemicals known to the State of California to cause
birth defects and, in some cases, cancer. (California Health &
Safety Code Section 25249.5 et seq.)
For Gasoline Engines:
Y Engine exhaust contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive
harm.
Y Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of
California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
For Diesel Engines:
Y Diesel engine exhaust and some of its constituents are known
to the State of California to cause cancer, birth defects, and
other reproductive harm.
OM-1500-14 Page 3
1-5. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Boulevard, Rexdale, Ontario, Canada M9W 1R3 (phone:
800−463−6727 or in Toronto 416−747−4044, website: www.csa−international.org).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard
AWS F4.1 from Global Engineering Documents (phone:
1-877-413-5184, website: www.global.ihs.com).
Practice For Occupational And Educational Eye And Face Protection,
ANSI Standard Z87.1, from American National Standards Institute, 11
West 42nd Street, New York, NY 10036−8002 (phone: 212−642−4900,
website: www.ansi.org).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA
02269−9101 (phone: 617−770−3000, website: www.nfpa.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (phone:
617−770−3000,website: www.nfpa.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 1735 Jefferson Davis Highway,
Suite 1004, Arlington, VA 22202−4102 (phone: 703−412−0900, website: www.cganet.com).
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 178 Rexdale
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (there
are 10 Regional Offices−−phone for Region 5, Chicago, is
312−353−2220,website: www.osha.gov).
1-6. EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
Welding current, as it flows through welding cables, will cause electromagnetic fields. There has been and still is some concern about such
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National
Research Council concluded that: “The body of evidence, in the
committee’s judgment, has not demonstrated that exposure to powerfrequency electric and magnetic fields is a human-health hazard.”
However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you
may wish to minimize your exposure to electromagnetic fields when
welding or cutting.
To reduce magnetic fields in the workplace, use the following
procedures:
OM-1500-14 Page 4
1. Keep cables close together by twisting or taping them.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cables around your body.
4. Keep welding power source and cables as far away from operator as practical.
5. Connect work clamp to workpiece as close to the weld as possible.
About Pacemakers:
Pacemaker wearers consult your doctor before welding or going near
welding operations. If cleared by your doctor, then following the above
procedures is recommended.
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION
som _3/05
Y Avertissement : se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes.
2-1.
Symboles utilisés
Symbole graphique d’avertissement ! Attention ! Cette procédure comporte des risques possibles ! Les dangers éventuels sont représentés par les symboles graphiques joints.
Y Indique un message de sécurité particulier
. Signifie NOTE ; n’est pas relatif à la sécurité.
2-2.
Ce groupe de symboles signifie Avertissement ! Attention ! Risques
d’ÉLECTROCUTION, ORGANES MOBILES et PARTIES
CHAUDES. Consulter les symboles et les instructions afférentes
ci-dessous concernant les mesures à prendre pour supprimer
les dangers.
Dangers relatifs au soudage à l’arc
Y Les symboles représentés ci-dessous sont utilisés dans ce manuel
pour attirer l’attention et identifier les dangers possibles. En
présence de l’un de ces symboles, prendre garde et suivre les
instructions afférentes pour éviter tout risque. Les instructions en
matière de sécurité indiquées ci-dessous ne constituent qu’un
sommaire des instructions de sécurité plus complètes fournies
dans les normes de sécurité énumérées dans la Section 2-5. Lire et
observer toutes les normes de sécurité.
Y Seul un personnel qualifié est autorisé à installer, faire fonctionner, entretenir et réparer cet appareil.
Y Pendant le fonctionnement, maintenir à distance toutes les personnes, notamment les enfants de l’appareil.
D Vérifier fréquemment le cordon d’alimentation afin de s’assurer qu’il
D
D
D
D
D
D
UNE DÉCHARGE ÉLECTRIQUE peut
entraîner la mort.
D
Le contact d’organes électriques sous tension peut
provoquer des accidents mortels ou des brûlures
graves. Le circuit de l’électrode et de la pièce est
sous tension lorsque le courant est délivré à la
sortie. Le circuit d’alimentation et les circuits internes de la machine
sont également sous tension lorsque l’alimentation est sur Marche.
Dans le mode de soudage avec du fil, le fil, le dérouleur, le bloc de
commande du rouleau et toutes les parties métalliques en contact
avec le fil sont sous tension électrique. Un équipement installé ou mis
à la terre de manière incorrecte ou impropre constitue un danger.
D
D
D Ne pas toucher aux pièces électriques sous tension.
D Porter des gants isolants et des vêtements de protection secs et sans
D
D
D
D
D
D
D
D
D
trous.
S’isoler de la pièce à couper et du sol en utilisant des housses ou des
tapis assez grands afin d’éviter tout contact physique avec la pièce à
couper ou le sol.
Ne pas se servir de source électrique à courant électrique dans les zones humides, dans les endroits confinés ou là où on risque de tomber.
Se servir d’une source électrique à courant électrique UNIQUEMENT si
le procédé de soudage le demande.
Si l’utilisation d’une source électrique à courant électrique s’avère nécessaire, se servir de la fonction de télécommande si l’appareil en est
équipé.
D’autres consignes de sécurité sont nécessaires dans les conditions
suivantes : risques électriques dans un environnement humide ou si l’on
porte des vêtements mouillés ; sur des structures métalliques telles que
sols, grilles ou échafaudages ; en position coincée comme assise, à genoux ou couchée ; ou s’il y a un risque élevé de contact inévitable ou
accidentel avec la pièce à souder ou le sol. Dans ces conditions, utiliser
les équipements suivants, dans l’ordre indiqué : 1) un poste à souder DC
à tension constante (à fil), 2) un poste à souder DC manuel (électrode)
ou 3) un poste à souder AC à tension à vide réduite. Dans la plupart des
situations, l’utilisation d’un poste à souder DC à fil à tension constante
est recommandée. En outre, ne pas travailler seul !
Couper l’alimentation ou arrêter le moteur avant de procéder
à l’installation, à la réparation ou à l’entretien de l’appareil. Déverrouiller
l’alimentation selon la norme OSHA 29 CFR 1910.147 (voir normes de
sécurité).
Installer le poste correctement et le mettre à la terre convenablement
selon les consignes du manuel de l’opérateur et les normes nationales,
provinciales et locales.
Toujours vérifier la terre du cordon d’alimentation. Vérifier et s’assurer
que le fil de terre du cordon d’alimentation est bien raccordé à la borne
de terre du sectionneur ou que la fiche du cordon est raccordée à une
prise correctement mise à la terre.
En effectuant les raccordements d’entrée, fixer d’abord le conducteur
de mise à la terre approprié et contre-vérifier les connexions.
D
D
D
n’est pas altéré ou à nu, le remplacer immédiatement s’il l’est. Un fil à nu
peut entraîner la mort.
L’équipement doit être hors tension lorsqu’il n’est pas utilisé.
Ne pas utiliser des câbles usés, endommagés, de grosseur insuffisante
ou mal épissés.
Ne pas enrouler les câbles autour du corps.
Si la pièce soudée doit être mise à la terre, le faire directement avec un
câble distinct.
Ne pas toucher l’électrode quand on est en contact avec la pièce, la terre
ou une électrode provenant d’une autre machine.
Ne pas toucher des porte électrodes connectés à deux machines en
même temps à cause de la présence d’une tension à vide doublée.
N’utiliser qu’un matériel en bon état. Réparer ou remplacer sur-lechamp les pièces endommagées. Entretenir l’appareil conformément à
ce manuel.
Porter un harnais de sécurité si l’on doit travailler au-dessus du sol.
S’assurer que tous les panneaux et couvercles sont correctement en
place.
Fixer le câble de retour de façon à obtenir un bon contact métal-métal
avec la pièce à souder ou la table de travail, le plus près possible de la
soudure.
Isoler la pince de masse quand pas mis à la pièce pour éviter le contact
avec tout objet métallique.
Ne pas raccorder plus d’une électrode ou plus d’un câble de masse à
une même borne de sortie de soudage.
Il reste une TENSION DC NON NÉGLIGEABLE dans
les sources de soudage onduleur quand on a coupé
l’alimentation.
D Arrêter les convertisseurs, débrancher le courant électrique et
décharger les condensateurs d’alimentation selon les instructions indiquées dans la partie Entretien avant de toucher les pièces.
LES FUMÉES ET LES GAZ peuvent
être dangereux.
Le soudage génère des fumées et des gaz. Leur
inhalation peut être dangereuse pour la santé.
D Ne pas mettre sa tête au-dessus des vapeurs. Ne pas respirer ces vapeurs.
D À l’intérieur, ventiler la zone et/ou utiliser une ventilation forcée au niveau de
l’arc pour l’évacuation des fumées et des gaz de soudage.
D Si la ventilation est médiocre, porter un respirateur anti-vapeurs approuvé.
D Lire et comprendre les spécifications de sécurité des matériaux (MSDS) et
les instructions du fabricant concernant les métaux, les consommables, les
revêtements, les nettoyants et les dégraisseurs.
D Travailler dans un espace fermé seulement s’il est bien ventilé ou en
portant un respirateur à alimentation d’air. Demander toujours à un surveillant dûment formé de se tenir à proximité. Des fumées et des gaz de
soudage peuvent déplacer l’air et abaisser le niveau d’oxygène provoquant des blessures ou des accidents mortels. S’assurer que l’air de
respiration ne présente aucun danger.
D Ne pas souder dans des endroits situés à proximité d’opérations de dégraissage, de nettoyage ou de pulvérisation. La chaleur et les rayons de
l’arc peuvent réagir en présence de vapeurs et former des gaz hautement toxiques et irritants.
D Ne pas souder des métaux munis d’un revêtement, tels que l’acier galvanisé, plaqué en plomb ou au cadmium à moins que le revêtement n’ait
été enlevé dans la zone de soudure, que l’endroit soit bien ventilé et en
portant un respirateur à alimentation d’air. Les revêtements et tous les
métaux renfermant ces éléments peuvent dégager des fumées toxiques en cas de soudage.
OM-1500-14 Page 5
LES RAYONS D’ARC peuvent entraîner des brûlures aux yeux et à la peau.
Le rayonnement de l’arc du procédé de soudage
génère des rayons visibles et invisibles intenses
(ultraviolets et infrarouges) susceptibles de provoquer des brûlures dans les yeux et sur la peau.
Des étincelles sont projetées pendant le soudage.
D Porter un casque de soudage approuvé muni de verres filtrants approprié pour protéger visage et yeux pendant le soudage (voir ANSI
Z49.1 et Z87.1 énuméré dans les normes de sécurité).
D Porter des lunettes de sécurité avec écrans latéraux même sous votre casque.
D Avoir recours à des écrans protecteurs ou à des rideaux pour
protéger les autres contre les rayonnements les éblouissements et
les étincelles ; prévenir toute personne sur les lieux de ne pas
regarder l’arc.
D Porter des vêtements confectionnés avec des matières résistantes
et ignifuges (cuir, coton lourd ou laine) et des bottes de protection.
LE SOUDAGE peut provoquer un
incendie ou une explosion.
Le soudage effectué sur des conteneurs fermés tels
que des réservoirs, tambours ou des conduites peut
provoquer leur éclatement. Des étincelles peuvent
être projetées de l’arc de soudure. La projection
d’étincelles, des pièces chaudes et des équipements chauds peuvent
provoquer des incendies et des brûlures. Le contact accidentel de
l’électrode avec des objets métalliques peut provoquer des étincelles,
une explosion, une surchauffe ou un incendie. Avant de commencer
le soudage, vérifier et s’assurer que l’endroit ne présente pas de
danger.
D Déplacer toutes les substances inflammables à une distance de
10,7 m de l’arc de soudage. En cas d’impossibilité, les recouvrir soigneusement avec des protections homologuées.
D Ne pas souder dans un endroit où des étincelles peuvent tomber sur
des substances inflammables.
D Se protéger, ainsi que toute autre personne travaillant sur les lieux,
contre les étincelles et le métal chaud.
D Des étincelles et des matériaux chauds du soudage peuvent
facilement passer dans d’autres zones en traversant de petites
fissures et des ouvertures.
D Afin d’éliminer tout risque de feu, être vigilant et garder toujours un
extincteur à la portée de main.
D Le soudage effectué sur un plafond, plancher, paroi ou séparation
peut déclencher un incendie de l’autre côté.
D Ne pas effectuer le soudage sur des conteneurs fermés tels que des
réservoirs, tambours, ou conduites, à moins qu’ils n’aient été préparés correctement conformément à AWS F4.1 (voir les normes de
sécurité).
D Brancher le câble de masse sur la pièce le plus près possible de la
zone de soudage pour éviter le transport du courant sur une longue
distance par des chemins inconnus éventuels en provoquant des
risques d’électrocution, d’étincelles et d’incendie.
D Ne pas utiliser le poste de soudage pour dégeler des conduites
gelées.
D En cas de non-utilisation, enlever la baguette d’électrode du porteélectrode ou couper le fil à la pointe de contact.
D Porter des vêtements de protection exempts d’huile tels que des
gants en cuir, une veste résistante, des pantalons sans revers, des
bottes et un casque.
D Avant de souder, retirer toute substance combustible de ses poches
telles qu’un allumeur au butane ou des allumettes.
D Suivre les consignes de OSHA 1910.252 (a) (2) (iv) et de NFPA 51B
pour travaux de soudage et prévoir un détecteur d’incendie et un extincteur à proximité.
DES
PARTICULES
VOLANTES
peuvent blesser les yeux.
D Le soudage, l’écaillement, le passage de la
pièce à la brosse en fil de fer, et le meulage
génèrent des étincelles et des particules
métalliques volantes. Pendant la période de
refroidissement des soudures, elles risquent
de projeter du laitier.
D Porter des lunettes de sécurité avec écrans latéraux ou un écran
facial.
OM-1500-14 Page 6
LES ACCUMULATIONS DE GAZ
risquent de provoquer des blessures
ou même la mort.
D Fermer l’alimentation du gaz protecteur en cas
de non-utilisation.
D Veiller toujours à bien aérer les espaces confinés ou se servir d’un respirateur d’adduction
d’air homologué.
DES PIÈCES CHAUDES peuvent
provoquer des brûlures graves.
D Ne pas toucher des parties chaudes à mains
nues.
D Prévoir une période de refroidissement avant
d’utiliser le pistolet ou la torche.
D Ne pas toucher aux pièces chaudes, utiliser les outils recommandés et porter des gants de soudage et des vêtements épais
pour éviter les brûlures.
LES CHAMPS MAGNÉTIQUES peuvent
affecter les stimulateurs cardiaques.
D Porteurs de stimulateur cardiaque, rester
à distance.
D Les porteurs d’un stimulateur cardiaque doivent d’abord consulter leur médecin avant de
s’approcher des opérations de soudage à l’arc,
de gougeage ou de soudage par points.
LE BRUIT peut endommager l’ouïe.
Le bruit des processus et des équipements peut
affecter l’ouïe.
D Porter des protections approuvées pour les
oreilles si le niveau sonore est trop élevé.
LES BOUTEILLES peuvent exploser
si elles sont endommagées.
Des bouteilles de gaz protecteur contiennent du gaz
sous haute pression. Si une bouteille est endommagée, elle peut exploser. Du fait que les bouteilles de
gaz font normalement partie du procédé de soudage,
les manipuler avec précaution.
D Protéger les bouteilles de gaz comprimé d’une chaleur excessive, des chocs mécaniques, des dommages physiques, du laitier, des flammes ouvertes, des étincelles et des arcs.
D Placer les bouteilles debout en les fixant dans un support stationnaire ou dans un porte-bouteilles pour les empêcher de tomber ou de se renverser.
D Tenir les bouteilles éloignées des circuits de soudage ou autres
circuits électriques.
D Ne jamais placer une torche de soudage sur une bouteille à gaz.
D Une électrode de soudage ne doit jamais entrer en contact avec
une bouteille.
D Ne jamais souder une bouteille pressurisée − risque d’explosion.
D Utiliser seulement des bouteilles de gaz protecteur, régulateurs,
tuyaux et raccords convenables pour cette application spécifique ; les maintenir ainsi que les éléments associés en bon état.
D Détourner votre visage du détendeur-régulateur lorsque vous
ouvrez la soupape de la bouteille.
D Le couvercle du détendeur doit toujours être en place, sauf lorsque la bouteille est utilisée ou qu’elle est reliée pour usage ultérieur.
D Utiliser les équipements corrects, les bonnes procédures et suffisamment de personnes pour soulever et déplacer les bouteilles.
D Lire et suivre les instructions sur les bouteilles de gaz comprimé,
l’équipement connexe et le dépliant P-1 de la CGA (Compressed
Gas Association) mentionné dans les principales normes de sécurité.
2-3.
Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance
Risque D’INCENDIE OU D’EXPLOSION.
DES ORGANES MOBILES peuvent
provoquer des blessures.
D Ne pas placer l’appareil sur, au-dessus ou
à proximité de surfaces inflammables.
D Ne pas installer l’appareil à proximité de
produits inflammables.
D Ne pas surcharger l’installation électrique − s’assurer que
l’alimentation est correctement dimensionnée et protégée avant
de mettre l’appareil en service.
D S’abstenir de toucher des organes mobiles tels
que des ventilateurs.
D Maintenir fermés et verrouillés les portes,
panneaux, recouvrements et dispositifs de
protection.
D Seules des personnes qualifiées sont autorisées à enlever les
portes, panneaux, recouvrements ou dispositifs de protection
pour l’entretien.
D Remettre les portes, panneaux, recouvrements ou dispositifs de
protection quand l’entretien est terminé et avant de rebrancher
l’alimentation électrique.
LA CHUTE DE L’APPAREIL peut
blesser.
LIRE LES INSTRUCTIONS.
D Utiliser l’anneau de levage uniquement pour
soulever l’appareil, NON PAS les chariots, les
bouteilles de gaz ou tout autre accessoire.
D Utiliser un équipement de levage de capacité
suffisante pour lever l’appareil.
D En utilisant des fourches de levage pour déplacer l’unité, s’assurer que les fourches sont suffisamment longues pour dépasser
du côté opposé de l’appareil.
L’EMPLOI EXCESSIF peut
CHAUFFER L’ÉQUIPEMENT.
D Lire le manuel d’utilisation avant d’utiliser ou
d’intervenir sur l’appareil.
D Utiliser uniquement des pièces de rechange
Miller/Hobart.
LE
RAYONNEMENT
HAUTE
FRÉQUENCE (HF) risque de provoquer
des interférences.
SUR-
D Prévoir une période de refroidissement ;
respecter le cycle opératoire nominal.
D Réduire le courant ou le facteur de marche
avant de poursuivre le soudage.
D Ne pas obstruer les passages d’air du poste.
D
D
D
LES CHARGES ÉLECTROSTATIQUES
peuvent endommager les circuits
imprimés.
D
D
D Établir la connexion avec la barrette de terre
avant de manipuler des cartes ou des pièces.
D Utiliser des pochettes et des boîtes antistatiques pour stocker, déplacer ou expédier des
cartes PC.
LE SOUDAGE À L’ARC risque de
provoquer des interférences.
DES ORGANES MOBILES peuvent
provoquer des blessures.
D Ne pas s’approcher des organes mobiles.
D Ne pas s’approcher des points de coincement
tels que des rouleaux de commande.
D
D
LES FILS DE SOUDAGE peuvent
provoquer des blessures.
D
D Ne pas appuyer sur la gâchette avant d’en
avoir reçu l’instruction.
D Ne pas diriger le pistolet vers soi, d’autres
personnes ou toute pièce mécanique en engageant le fil de soudage.
2-4.
D Le rayonnement haute fréquence (HF) peut
provoquer des interférences avec les équipements de radio-navigation et de communication, les services de sécurité et les ordinateurs.
Demander seulement à des personnes qualifiées familiarisées
avec des équipements électroniques de faire fonctionner l’installation.
L’utilisateur est tenu de faire corriger rapidement par un électricien qualifié les interférences résultant de l’installation.
Si le FCC signale des interférences, arrêter immédiatement
l’appareil.
Effectuer régulièrement le contrôle et l’entretien de l’installation.
Maintenir soigneusement fermés les portes et les panneaux des
sources de haute fréquence, maintenir les éclateurs à une
distance correcte et utiliser une terre et un blindage pour réduire
les interférences éventuelles.
D
D L’énergie électromagnétique peut gêner le
fonctionnement d’appareils électroniques
comme des ordinateurs et des robots.
D Veiller à ce que tout l’équipement de la zone de
soudage soit compatible électromagnétiquement.
Pour réduire la possibilité d’interférence, maintenir les câbles de
soudage aussi courts que possible, les grouper, et les poser
aussi bas que possible (ex. par terre).
Veiller à souder à une distance de 100 mètres de tout équipement électronique sensible.
Veiller à ce que ce poste de soudage soit posé et mis à la terre
conformément à ce mode d’emploi.
En cas d’interférences après avoir pris les mesures précédentes, il incombe à l’utilisateur de prendre des mesures supplémentaires telles que le déplacement du poste, l’utilisation de
câbles blindés, l’utilisation de filtres de ligne ou la pose de protecteurs dans la zone de travail.
Proposition californienne 65 Avertissements
Y Les équipements de soudage et de coupage produisent des
fumées et des gaz qui contiennent des produits chimiques dont
l’État de Californie reconnaît qu’ils provoquent des malformations
congénitales et, dans certains cas, des cancers. (Code de santé et
de sécurité de Californie, chapitre 25249.5 et suivants)
Pour les moteurs à essence :
Y Les gaz d’échappement des moteurs contiennent des produits
chimiques dont l’État de Californie reconnaît qu’ils provoquent
des cancers et des malformations congénitales ou autres problèmes de procréation.
Y Les batteries, les bornes et autres accessoires contiennent du
plomb et des composés à base de plomb, produits chimiques
dont l’État de Californie reconnaît qu’ils provoquent des cancers et des malformations congénitales ou autres problèmes de
procréation. Se laver les mains après manipulation.
Pour les moteurs diesel :
Y Les gaz d’échappement des moteurs diesel et certains de leurs
composants sont reconnus par l’État de Californie comme
provoquant des cancers et des malformations congénitales ou autres problèmes de procréation.
OM-1500-14 Page 7
2-5.
Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
de Global Engineering Documents (téléphone : 1-877-413-5184, site Internet : www.global.ihs.com).
Boulevard, Rexdale, Ontario, Canada M9W 1R3 (téléphone :
800-463-6727 ou à Toronto 416-747-4044, site Internet :
www.csa-international.org).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard AWS
F4.1 de Global Engineering Documents (téléphone : 1-877-413-5184, site
Internet : www.global.ihs.com).
Practice For Occupational And Educational Eye And Face Protection,
ANSI Standard Z87.1, de American National Standards Institute, 11 West
42nd Street, New York, NY 10036-8002 (téléphone : 212-642-4900, site
Internet : www.ansi.org).
National Electrical Code, NFPA Standard 70, de National Fire Protection
Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA
02269-9101 (téléphone : 617-770-3000, site Internet : www.nfpa.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, de National Fire Protection Association, P.O.
Box 9101, 1 Battery March Park, Quincy, MA 02269-9101 (téléphone :
617-770-3000, site Internet : www.nfpa.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
de Compressed Gas Association, 1735 Jefferson Davis Highway, Suite
1004, Arlington, VA 22202-4102 (téléphone : 703-412-0900, site Internet
: www.cganet.com).
Code for Safety in Welding and Cutting, CSA Standard W117.2, de
Canadian Standards Association, Standards Sales, 178 Rexdale
2-6.
OSHA, Occupational Safety and Health Standards for General Industry,
Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and
Part 1926, Subpart J, de U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (il y a 10
bureaux régionaux−−le téléphone de la région 5, Chicago, est
312-353-2220, site Internet : www.osha.gov).
Information EMF
Considérations sur le soudage et les effets de basse fréquence et des
champs magnétiques et électriques.
Le courant de soudage, pendant son passage dans les câbles de soudage, causera des champs électromagnétiques. Il y a eu et il y a encore un
certain souci à propos de tels champs. Cependant, après avoir examiné
plus de 500 études qui ont été faites pendant une période de recherche
de 17 ans, un comité spécial ruban bleu du National Research Council a
conclu : « L’accumulation de preuves, suivant le jugement du comité, n’a
pas démontré que l’exposition aux champs magnétiques et champs électriques à haute fréquence représente un risque à la santé humaine ».
Toutefois, des études sont toujours en cours et les preuves continuent à
être examinées. En attendant que les conclusions finales de la recherche
soient établies, il vous serait souhaitable de réduire votre exposition aux
champs électromagnétiques pendant le soudage ou le coupage.
Pour réduire les champs magnétiques sur le poste de travail, appliquer
les procédures suivantes :
OM-1500-14 Page 8
1. Maintenir les câbles ensemble en les tordant ou en les enveloppant.
2. Disposer les câbles d’un côté et à distance de l’opérateur.
3. Ne pas courber pas et ne pas entourer pas les câbles autour de
votre corps.
4. Garder le poste de soudage et les câbles le plus loin possible de
vous.
5. Connecter la pince sur la pièce aussi près que possible de la soudure.
En ce qui concerne les stimulateurs cardiaques
Les porteurs de stimulateur cardiaque doivent consulter leur médecin
avant de souder ou d’approcher des opérations de soudage. Si le médecin approuve, il est recommandé de suivre les procédures précédentes.
SECTION 3 − INTRODUCTION
3-1. Specifications
Type of Input
Power
Welding Power
Source Type
24 Volts AC
Single-Phase
10 Amperes
50/60 Hertz
Wire Feed Speed
Range
Standard: 50 To 780 ipm
(1.3 To 19.8 mpm)
Constant Voltage (CV)
DC With 14-Pin And
Contactor Control
Optional High Speed: 92
To 1435 ipm
(2.3 To 36.5 mpm)
Wire Diameter
Range
Welding Circuit
Rating
.023 To 1/8 in (0.6
To 3.2 mm)
100 Volts,
750 Amperes, 100%
Duty Cycle
Max Spool Weight:
60 lb (27 kg)
Weight
12 ft (3.7 m):
207 lb (94 kg)
16 ft (4.9 m):
280 lb (127 kg)
12 ft (3.7 m) Boom (DS-12)
16 ft (4.9 m) Boom (DS-16)
Maximum Height With 4 ft (1.2 m) Post
17 ft (5.2 m)
21 ft (6.4 m)
Vertical Lift Of Boom
Horizontal to 60° Above Horizontal
Horizontal to 60° Above Horizontal
SECTION 4 − INSTALLATION
4-1. Installing Swivel Into Pipe Post
5
4
Y Do not remove Safety Collar
until instructed to.
1
2
3
Swingpak Base or CBC Cart
Pipe Post With Base
Steel Bolt
Secure as shown using as a minimum 1/2 in diameter SAE grade 5
steel bolts.
4
2
1
3
Swivel Assembly
Insert into pipe post. Lubricate
swivel.
5
Safety Collar
Tools Needed:
3/4 in
152 268-B
OM-1500-14 Page 9
4-2. Installing Control Box And Adjusting Tilt
1
2
3
Weld Control
Bracket
Screw
Bracket and screws are installed
onto bottom of control at factory.
4
1
5
2
6
4
7
Swivel
Loosen screws. Place control on
swivel and slide forward. Tighten
screws.
5
6
7
Tilt Bracket
Rear Pivot Screw
Front Screw
Loosen rear pivot screw. Remove
front screw. Pivot control downward to desired viewing angle. Replace and tighten front screw. Tighten pivot screw.
3
Tools Needed:
3/8 in
803 192
4-3. Installing Boom And Reel Support
1
2
Swivel Plates
Yoke
Remove hardware from swivel
plates and yoke.
3
Boom
Set boom into swivel as shown.
4
Yoke Pin
Install pin through yoke. Install cotter pin and spread ends.
3
7
5
6
4
Bolt
Install bolt, washers, and nut. Tighten hardware, and back bolt off one
half turn.
Locking Knob
Install locking knob but do not
tighten.
5
7
6
Reel Support
Install reel support.
2
1
Tools Needed:
3/8, 3/4 in
ST-153 170-A
OM-1500-14 Page 10
4-4. Installing Wire Guide Extension
1
2
3
4
1
4
3
2
Wire Guide Fitting
Bolt
Monocoil Liner
Wire Guide Extension
Tighten bolt to secure liner in wire
guide fitting. Do not overtighten bolt
and crush liner.
Repeat procedure for opposite
side.
Tools Needed:
3/8 in
ST-152 383
OM-1500-14 Page 11
4-5. Equipment Connection Diagram
1
2
3
Welding Power Source
Remote 14 Connection
Negative (−) Weld Output
Cable
4 Positive (+) Weld Output
Cable
5 Workpiece
6 Weld Control
7 Boom
8 Gun
9 Swivel
10 Pipe Post And Base
11 Gas Hose
12 Gas Supply and Regulator
(Customer Supplied)
12
1
2
. Shielding gas pressure not to
exceed 100 PSI (689 kPa).
3
4
5
11
6
7
10
9
8
803 195
OM-1500-14 Page 12
4-6. Control Box Connections
1
2
3
Interconnecting Cables
Interconnecting Cable
Receptacles
14-Pin Cord
1
2
3
803 197-A
4-7. 14-Pin Plug Information
Pin*
I
G
A
24 volts ac with respect to socket G.
A
B
Contact closure to A completes 24 volts ac contactor control circuit.
B
L C
M D
E
G
Circuit common for 24 volts AC circuit.
C
+10 volts dc input from power source to wire feeder with respect to socket D.
D
Remote control circuit common.
E
0 to +10 volts dc output signal from wire feeder to power source with respect to socket D.
H
Voltage feedback; 0 to +10 volts dc, 1 volt per 10 arc volts.
F
Current feedback; 0 to +10 volts dc, 1 volt per 100 amperes.
J
H
K
N
F
Pin Information
*The remaining pins are not used.
OM-1500-14 Page 13
4-8. Removing Safety Collar And Adjusting Boom
1
Locking Knob
Tighten knob to prevent boom
movement. Loosen knob to allow
boom movement. Change knob position to limit upward movement.
Pull boom down slightly and remove safety collar. Boom should
balance in any position from horizontal to 60 degrees above horizontal. If necessary, adjust boom
as follows:
4
2
3
Loosen jam nut and turn threaded
rod until boom balances. Tighten
jam nut. Be sure several full threads
are through yoke to prevent boom
falling.
4 Yoke
5 Safety Collar
5
2
1
Threaded Rod
Jam Nut
Retain safety collar for use in disassembling or moving boom.
3
4
Rod
Rod
Tools Needed:
3
2
Decreasing Spring
Increasing Spring
Pressure For A
Pressure For A Heavy
Lighter Gun
Gun
1-1/8 in
ST-142 599-C
4-9. Gun Recommendation Table
Process
Gun
GMAW − Hard or Cored Wires
Roughneck C-Series Guns: 300, 400, 500, And
600 Amp.
FCAW − Self-Shielding Wires
FC-1260 Or FC-1150
4-10. Wire Type, Size, And Feed Speed Capability Table
Motor Speed
Wire Type
Wire Size
Feed Speed Capability
Standard
All
.023 To 5/64 in (0.6 To 2 mm)
50 To 780 ipm (1.3 To 19.8 mpm)
Standard
All
3/32 To 7/64 in (2.4 To 2.8 mm)
50 To 700 ipm (1.3 To 17.8 mpm)
Standard
All
1/8 in (3.2 mm)
50 To 300 ipm (1.3 To 7.6 mpm)
Optional High
Speed
All
.023 To 5/64 in (0.6 To 2 mm)
92 To 1435 ipm (2.3 To 35.6 mpm)
OM-1500-14 Page 14
4-11. Installing And Threading Welding Wire
Tools Needed:
3/16, 5/64 in
3/8, 15/16 in
Install wire spool. Adjust tension nut so
wire is taut when wire
feed stops.
Pressure
Adjust
Pressure
Indicator
Scale
Install wire guide.
Pressure
Adjust
Drive Rolls
Install drive rolls.
Gun Cable
End Of Liner
NONCONDUCTIVE
SURFACE
No Wire Slip
. Be sure that outlet cable has proper
size liner for the welding wire size.
When installing gun, position liner
extending from outlet wire guide as
close as possible to drive rolls without touching.
Install gun. Lay gun cable out straight. Cut off
end of wire. Push wire through guides up to
drive rolls; continue to hold wire. Press Jog
button to feed wire out gun.
NONCONDUCTIVE
SURFACE
Wire Slips
. For soft wire or small diameter stainless
steel wire, reduce drive roll pressure on
the rear roll to half that of the front rolls.
. To adjust drive roll pressure, hold nozzle
about 2 in (51 mm) from nonconductive
surface and press gun trigger to feed wire
against surface. Tighten knob so wire
does not slip. Do not overtighten. If contact tip is completely blocked, wire should
slip at the feeder (see pressure adjustment above). Cut wire off. Close cover.
803 196 / 152 648-A / 803 020 / 802 966 / Ref. 137 391-A / 802 954 / Ref. S-0627-A
OM-1500-14 Page 15
4-12. Setting Internal DIP Switches
1
2
DIP Switch S1
DIP Switch S4 (Not For Customer Use)
DIP switch S1 allows the user to make a number of choices affecting unit operation.
w Defining Motor Speed (S1-7 & 8)
Switches 7 and 8 allow the user to define
whether the motor in use is standard speed
(50-780 inches per minute), or high speed
(92-1435 inches per minute).
. Setting DIP switches allows the feeder to
display the proper wire speed. Setting
the DIP switches will not change the
speed range of the motors.
. When DIP switch positions are changed, the
unit must be turned Off and then On again in
order for the new settings to be active. DIP
switches are only read on power up.
1
O 1
N
2
3
4
5
6
7
8
. In the DIP switch S1 illustrations,
2
the elevated slider on each switch
is shown in white. For example,
the switches above are all in the
Off position.
803 198
Position Settings And Results For DIP Switch S1
7
8
7 Off, 8 Off = Standard
speed motor (50-780 inches per minute, or 1.2-19.8
meters per minute)
7
8
7 Off, 8 On = High speed
motor (92-1435 inches per
minute, or 2.3-36.4 meters
per minute)
OM-1500-14 Page 16
4-13. Power Source Selection Menu
1
2
Non-CE Model Shown
. When the feeder is turned on,
1
Program
Volts
Upper Display
Lower Display
the Power Source Selection
Menu allows the operator to select a default power source.
Selecting a default power
source, automatically sets the
correct Vmin and Vmax settings for adjusting the output
voltage of the power source.
Time (sec)
First Time Feeder Is Turned On
Wire Speed
Amps
Start
Trigger Hold
Crater
Pre/Postflow
Sequence
The feeder automatically goes into
the Power Source Selection Menu.
The feeder displays “dELT” on the
Upper Display and “452” on the
Lower Display, meaning that a Deltaweld 452 is the default power
source, and has a voltage range of
10V as Vmin and 38V as Vmax.
2
Dual Schedule
Adjust
Setup
Upper Display
Lower Display
Deltaweld 452
dELT
452
Vmin =10
Vmax =38
Deltaweld 302
dELT
302
Vmin =10
Vmax =32
Deltaweld 652
dELT
652
Vmin =10
Vmax =44
Dimension 302
dIM
302
Vmin =10
Vmax =32
Dimension 452
dIM
452
Vmin =10
Vmax =38
* * Power Source
Voltage Range
Dimension 652
dIM
652
Vmin =10
Vmax =65
Dimension 1000
dIM
1000
Vmin =10
Vmax =60
XMT 304
XMT
304
Vmin =10
Vmax =35
XMT 456
XMT
456
Vmin =10
Vmax =38
Invision 354MP
I354
MP
Vmin =10
Vmax =35
Invision 456MP
I456
MP
Vmin =10
Vmax =38
Invision 456P
I456
P
Vmin =10
Vmax =38
PHOENIX 456
PHX
456
Vmin =10
Vmax =38
SUMMIT ARC 1000
SUM
1000
Vmin =25
Vmax =44
** For any power sources not listed, pick a matching voltage range, or see Sec 4-12 to
set Vmin and Vmax.
At power up, the operator has three
seconds to select a default power
source from the list shown on the
display. Operator may scroll
through the list of power sources by
using the Adjust control. After selecting a power source the operator
has three seconds to change to a
different power source or begin
welding. After making a power
source selection, the operator may
press the Program Button to avoid
having to wait the three seconds.
When turning off the feeder, the default power source will be retained.
If voltage settings have already
been set with the Vmin and Vmax in
the Auxiliary Menu, selecting a default power source with the Power
Source Selection Menu overrides
the Vmin and Vmax voltage settings.
Next Time Feeder Is Turned On
The feeder will display the last selected default power source. The
operator has three seconds to select another power source, or press
the Program Button to exit the Power Source Selection Menu.
Disabling The Power Source
Selection Menu
Once the default power source has
been selected the Power Source
Selection Menu may be disabled
using the Auxiliary Menus. See
Section 5-12.
OM-1500-14 Page 17
SECTION 5 − OPERATION
5-1. Operational Terms
The following is a list of terms and their definitions as they apply to this wire feeder:
General Terms:
Cold Wire Jog
Feeding wire without contactor or gas valve being energized.
Sequence
A portion of the weld program, such as preflow, run-in, start, weld, crater, burnback, and postflow.
Weld Program
A group of sequences that make up a weld cycle.
5-2. Power Switch
1
Power Switch
1
803 193
5-3. Left/Right Select Switch
1
Left/Right Select Switch
Pressing the Left/Right Select
switch allows the operator to
choose which side of the units’ controls will operate.
1
. Engaging the Left or Right
Gun Trigger also allows the
operator to enable the controls on that side of the unit.
803 194
OM-1500-14 Page 18
5-4. Jog/Purge Switch
1
2
Jog/Purge Switch
Adjust Control
2
1
Pressing the Jog/Purge switch allows the operator to jog wire without energizing the weld
power or gas valve circuit.
• The unit provides the ability to jog the wire
feeder by means of the gun trigger or the
Jog/Purge switch. If the welding arc does
not initiate in 3 seconds after the gun trigger
is activated, the unit will perform a jog operation for a maximum of two minutes. If the gun
803 194
trigger is still activated after two minutes, the
jog operation is terminated to prevent complete despooling of the wire, in the case of
a damaged gun.
• The unit displays the “ERR TRIG“ message
to inform the operator that the trigger is activated.
• Jog speed can be adjusted by the Adjust
control when the unit is jogging wire. The
unit displays jog speed when the unit is being jogged.
• Jogging can also be accomplished by
pressing the Jog/Purge button.
• Pressing the Jog/Purge button also allows
the operator to purge gas lines before welding and to preset gas pressure at the
regulator.
5-5. Front Panel Controls
See
Section
5-7
See
Section
5-6
Program
Volts
Wire Speed
Amps
Start
Crater
Pre/Postflow
Dual Schedule
Trigger Hold
Adjust
Sequence
See
Section
5-11
See
Section
5-8
Time (sec)
See
Section
5-10
Setup
See
Section
5-9
OM-1500-14 Page 19
5-6. Program Push Button
1
Program Display
The number of the active program
is displayed.
2
Program Push Button
Press button to activate program
select feature. To change the program number, press the Program
push button and rotate the Adjust
control.
1
Program
3
3
2
Program Push Button LED
The LED lights to indicate the Program push button is active.
5-7. Upper Display
. To set the correct voltage range for a particular power
source, see Section 4-13 for power source selection menu,
or Section 5-12 for V-Min And V-Max adjustments.
3
1
2
4
Volts
Time (sec)
5
1
Upper Display
The upper display shows voltage or time.
The unit displays both preset and actual arc
voltage. When the unit is in a welding state,
actual arc voltage is displayed. The upper
display shows welding sequence time when
the Time LED is illuminated.
2
Upper Display Push Button
Press and hold button to adjust or display
weld time. Release button to display voltage.
3
Upper Display Push Button LED
The upper display push button LED illumi-
OM-1500-14 Page 20
nates to indicate that information displayed
can be changed by the Adjust control.
4
5
Volts LED
Time LED
The LEDs below the display illuminate to indicate which value is being shown.
At any time while welding, the unit permits
the adjustment of the weld sequence voltage
and overrides the display of actual arc voltage.
• If the unit is displaying a welding sequence
that can be timed, the welding time display
mode is entered by pressing the upper dis-
play push button repeatedly until welding
time is the active parameter in the upper
display. At idle, the upper display toggles
between showing weld voltage or weld
time, with subsequent presses of the upper display push button.
• The unit defaults to displaying welding
voltage when a welding sequence display
mode is first entered.
• If the weld sequence has a time set (as in
spot time), after the weld program is completed, ERR TRG 1 will be displayed to indicate the weld program is complete. Release trigger to clear error.
5-8. Lower Display
3
1
2
4
Wire Speed
Amps
5
1
Lower Display
2
4
5
Wire Speed LED
Amps LED
The LEDs below the display illuminate to indicate which value is being shown.
Lower Display Push Button
• If the unit is in a welding state that does not
involve feeding wire, the unit displays the
weld sequence wire speed. At any time during welding, the weld sequence wire speed
can be adjusted and overrides the preset
wire speed display. In other words, if the Ad-
Press button to choose between wire speed or
amperage functions.
3
just control is activated while welding, the
unit displays and permits adjustment of the
weld sequence wire feed speed regardless
of the active welding sequence.
to indicate that information displayed can be
changed by the Adjust control.
The lower display shows wire speed or
amperage. The unit displays and adjusts only
preset wire speed at idle. When the unit is in a
welding state, actual wire speed is displayed
for the active welding sequence.
Lower Display Push Button LED
The lower display push button LED illuminates
• When the unit is displaying amperage, the
Amps LED illuminates. Amperage is only
displayed if the unit is in a welding state and
the amperage is above a minimum value of
25 Amps.
• The display will read dashes for amperage
readings below the amperage threshold,
prior to arc initiation.
5-9. Setup Push Button
3
4
Trigger Hold
Dual Schedule
2
1
Setup
1 Setup Push Button
Press button to choose between trigger hold
or dual schedule functions.
2 Setup Push Button LED
3 Trigger Hold LED
4 Dual Schedule LED
• When the Setup button is pressed, the Setup push button LED flashes and the Trigger
Hold LED flashes.
• The flashing LED indicates that the unit is in
the trigger hold display mode. In this mode
the upper display indicates HOLD and the
lower display indicates the trigger hold status On/Off. Use the Adjust control to change
the trigger hold status or press the lower display push button. If trigger hold is turned On,
the trigger hold LED illuminates and stays
On.
• When trigger hold is On, the user must
press and hold the trigger for a predefined
amount of time (the trigger hold delay time−
see Section 5-12), then release it for the trigger hold function to be active. To shut off the
weld when trigger hold is On, the user must
press and release the trigger.
• If a weld time is programmed, trigger hold is
disabled.
• Trigger hold and dual schedule cannot be
used concurrently.
• When the Setup button is pressed a second
time, the dual schedule LED flashes. In this
mode the upper display indicates DUAL and
the lower display indicates dual schedule
status On/Off. Use the Adjust control to
change the dual schedule status if desired.
• Pressing the Setup button again exits the
Setup mode. The dual schedule LED stops
flashing to indicate the dual schedule status
is Off.
• While in the Setup mode, the active program
can be adjusted without deactivating the
trigger hold Setup mode operation. If the
trigger is activated, Setup mode(s) is terminated.
OM-1500-14 Page 21
5-10. Adjust Control
1
Adjust Control
The Adjust control is used to
change various sequence parameters, and to select various sequences. Refer to the section for
the function in question for information related to using the Adjust control.
1
Adjust
5-11. Sequence Push Button
1
2
3
Start
3
Sequence Push Button
Sequence Push Button LED
Welding Sequence LEDs
Crater
Pre/Postflow
2
1
Start
Time
Preflow
Time
Weld
Time
Crater
Time
Postflow
Time
Sequence
Welding Sequence Diagram
. For more information on Setting
Sequence Parameters see Section 6-1.
• The Sequence push button allows the
selection of welding sequences. Five welding sequences are available. The default
sequence is the Weld sequence. The Weld
sequence is active on power up. Three
welding sequence LEDs are located above
the Sequence push button: Start, Crater,
and Preflow/Postflow. The applicable LED
illuminates to indicate which welding sequence is active.
• The LED illuminates to indicate that a welding sequence display mode other than Weld
is activate. Welding sequences other than
Weld must be set prior to initiating the arc.
When the unit enters a welding state, all sequence display modes are terminated and
OM-1500-14 Page 22
the weld display mode is activated.
If zero time is programmed for a timed sequence except for Weld, that sequence will
be skipped.
• In the weld sequence display mode the Sequence push button LED is Off. When the
Sequence push button is pressed, the Sequence push button flashes and the Start
LEDs flash. In this condition, the unit is in the
Start sequence display mode, and Start sequence parameters are shown in the displays.
• When the Sequence push button is pressed
a second time, the Crater sequence LED
flashes. The Sequence push button LED remains flashing. In this condition, the unit is
in the Crater sequence display mode, and
Crater sequence parameters are shown in
the displays.
• When the Sequence push button is pressed
a third time, the Preflow/Postflow sequence
LED flashes. The Sequence push button
LED remains flashing. In the Preflow display
mode the upper display shows the preflow
time and the lower display indicates the abbreviation PRE, to inform the operator that
preflow time is displayed. If the upper display push button is pressed, the Adjust control can be used to adjust preflow.
If the lower display push button is pressed, the
Adjust control can be used to select between
preflow PRE and postflow POST. When
POST is selected, the upper display can be
used to specify postflow time.
• When the Sequence push button is pressed
a fourth time, the unit returns to the welding
sequence display mode.
5-12. Auxiliary Menus
1
2
3
4
5
6
7
8
9
4
5
1
2
7
Program
Volts
Time (sec)
Wire Speed
Amps
6
Start
Trigger Hold
Crater
Pre/Postflow
Dual Schedule
3
Sequence
Program Display
Program Push Button
Sequence Push Button
Upper Display
Upper Display Push Button
Lower Display
Lower Display Push Button
Adjust Control
Setup Push Button
Adjust
9
Setup
8
5-12 Auxiliary Menus (Continued)
Reset To Factory Settings
A reset menu is displayed if the following four
push buttons are pressed simultaneously:
Program, Sequence, upper display, and Setup. The upper display indicates “WIPE” . The
lower display indicates “OFF”. The lower push
button is active indicating that the Adjust control can be used to change the unit to “WIPE
ON”. When “WIPE ON” is set, if the original
four push buttons are simultaneously pressed
a second time, the unit will reset all settings to
factory default except the arc time and arc
cycle counts. If a reset is not desired, set the
display to “WIPE OFF” and simultaneously
press the Program, Sequence, upper display,
and Setup push buttons to exit the reset menu.
Auxiliary Menu
• An auxiliary menu is provided if both the Sequence and Setup push buttons are pressed
simultaneously. The Setup push button and
sequence push button LEDS flash when the
auxiliary menu is displayed.
Pushing the Setup push button will step
through the menu. Pushing the sequence
push button will step through the menu in reverse.
power source min and max voltage preset
range. The minimum voltage is displayed in
the upper display and the lower display indicates “VMIN”. When the Setup push button
is pressed the unit displays the maximum
voltage setting of the welding power source.
The maximum voltage is displayed in the upper display and the lower display indicates
“VMAX”.
In both cases, the Adjust control is used to
specify the minimum and maximum voltage
settings of the welding power source. The settings correspond to arc voltage obtained at
minimum command and arc voltage obtained
at maximum command.
This method of setting “VMIN” and “VMAX”
may be used if the power source being used
is not listed in the Power Source Selection
Menu.
. If a default power source has already been
selected with the Power Source Selection
menu, setting “VMIN” and “VMAX” will
override the default power source settings.
power source selection menu must
. The auxiliary menu may be exited at any . The
be set to “OFF” when overriding the detime by pressing both the Sequence push
button and the Setup push buttons simultaneously.
V-Min And V-Max
• If the Setup push button is pressed, the unit
allows the setting of the manual override
The upper display shows “PSS”. Lower display shows “On” or “Off”. The Adjust Control is
used to select either “On” or “Off”.
Arc Time
• If the Setup push button is pressed, the unit
displays arc time in hours.
Arc time is indicated by the Program display
showing “HR”. Arc time is shown in the lower
display.
Cycles
• If the Setup push button is pressed, the unit
displays the number of cycles.
Arc cycles are indicated by the Program display showing “CL”. The arc cycle count is
shown in the lower display.
Run-In
• If the Setup button is pressed, the unit allows
setting the run-in modes. The run-in modes
are program specific. Each program may be
set to its own run-in mode.
The upper display indicates “RUNI”. The
lower display indicates “AUTO”, meaning the
factory set automatic run-in speed is selected.
Power Source Selection Menu
Pressing the lower display button allows a
manual setting the run-in wire speed. Speed
may be adjusted from 10% to 100% of weld
wire speed.
• If the Setup push button is pressed, the unit
allows the Power Source Selection menu to
be disabled or enabled.
Pressing the lower display button allows disabling of the run-in feature. When the lower
display indicates “OFF” run-in is disabled.
fault “VMIN” or “VMAX” settings.
OM-1500-14 Page 23
5-12 Auxiliary Menus (Continued)
Burnback
• If the Setup push button is pressed, the unit
allows burnback time to be set.
Burnback time and voltage can be specified
when the lower display indicates “BURN” and
the upper display indicates the burnback time
or voltage. The Adjust control is used to set the
desired burnback time or voltage. Burnback
settings, like run-in settings, are program specific. The active program is displayed in the
Program display and can be adjusted (see
Section 5-6).
Trigger Hold Setup
• If the Setup push button is pressed, the unit
allows trigger hold delay time to be set.
Trigger hold delay time is indicated by ”HOLD”
in the lower display and the hold delay time in
the upper display. The adjust control can be
used to specify a new delay time for trigger
hold. Trigger hold delay time is the minimum
amount of time the trigger must be held for trigger hold to work when the trigger is released
(the trigger hold function must be on). For example, if a trigger hold delay time of 2.0 seconds is defined, the operator must hold the
trigger for at least 2 seconds before releasing
it in order for the trigger hold function to work.
Once the trigger hold function is in effect, the
wire feeder will stay On until the trigger is
pressed and released again.
• There is an additional function built in called
”maximum trigger hold time” which is the
maximum length of time the trigger can be
held and the trigger hold function still work
when the trigger is released (the trigger hold
function must be on). The maximum trigger
hold time is set at 4.0 seconds after the trigger hold delay time. For example, if a trigger
hold delay time of 2.0 seconds is defined,
and the operator held the trigger in for more
than 6.0 seconds, the trigger hold function
would not be in effect and the wire feeder
would stop when the trigger is released.
• When the Setup push button is pressed
again, the menu repeats to the first menu
selection of run-in wire speed selection.
Trigger Program Select
• If the Setup push button is pressed, the unit
allows Trigger Program Select to be disabled or enabled.
The upper display shows “TSEL”. Lower display shows “On” or “Off”. The Adjust Control is
used to select either “On” or “Off”.
Trigger Program Select allows the operator to
select programs by clicking the trigger (pulling
and releasing the trigger in a maximum of 0.2
OM-1500-14 Page 24
seconds). The feeder will switch between any
programs that have a minimum of 0.2 seconds
of preflow time set in the weld sequence. If programs 1 and 3 have a minimum of 0.2 seconds
of preflow time, clicking the trigger will toggle
between programs 1 and 3. If programs 1, 2,
and 4 have a minimum of 0.2 seconds of preflow time, clicking the trigger will switch from 1
to 2 to 4 to 1 to 2. Any combination of programs
may be used. Trigger Program Select cannot
be used while welding or with Dual Schedule.
Process Select
Process selection indicated by ”PROS” in the
upper display is set to either ”VOLT” or ”TRIM”
in the lower display. Each program can be selected be be a MIG program indicated by
”VOLT” or a pulsing program indicated by
”TRIM”.
Range Locks
Range locks are indicated by “LOCK” in the
upper display for wire speed or “LOCK” in the
lower display for voltage range. In a MIG program, the voltage range lock ranges from 0 to
10 volts. In a pulse program, the trim range
lock ranges from 0 to 100. The wire feed speed
range lock ranges from 0 to 250 ipm. Locks are
program dependent and wire speed is independent from voltage or trim.
Wire Feed Speed Units
Wire feed speed setting indicated by “WFS” in
the upper display is set to “IPM” inches−per−
minute or ”MPM” meters−per−minute. This
setting is independent of the program selected.
OPT1
• If the Setup push button is pressed, the unit
allows OPT1 to be disabled or enabled.
The upper display shows “OPT1”. Lower display shows “On” or “Off”. The Adjust Control is
used to select either “On” or “Off”.
“OPT1” is used by the Water Flow Shutdown
Option to stop the weld sequence if water flow
to a water cooled gun is interrupted. A closed
set of contacts between pins 1 and 2 of RC26
on Interface Board (PC20) will allow feeder to
operate normally. Opening the contacts will
stop the weld sequence and display “ERR” in
the upper display and “OPT1” in the lower display.
OPT2
• If the Setup push button is pressed, the unit
allows OPT2 to be disabled or enabled.
The upper display shows “OPT2”. Lower display shows “On” or “Off”. The Adjust Control is
used to select either “On” or “Off”.
“OPT2” is a second input that may be used
with an external device, such as a gas flow
switch, to end the weld sequence. The gas
flow switch may be used to stop the weld sequence if shielding gas flow to the gun is interrupted. A closed set of contacts between pins
1 and 2 of RC24 on Interface Board (PC20) will
allow feeder to operate normally. Opening the
contacts will stop the weld sequence and display “ERR” in the upper display and “OPT2” in
the lower display.
Display Hold
Display hold indicated by ”DISP” in the upper
display is set to “OFF” or “HOLD” in the lower
display. When ”HOLD” is selected, the unit will
hold the last weld information for 5 seconds following weld termination. If any front panel
push button is pressed, or if the Adjust control
is activated, the display hold feature is terminated.
Software Revision Level
• If the Setup push button is pressed, the unit
displays the software version being used by
the interface PCB (PC20).
• When the Setup button is pressed again, the
menu repeats.
Code
Upon leaving the auxiliary menu, the user is
asked if a password code indicated by
“CODE” in the top display should be activated.
By default the code is off, indicated by “OFF”
in the lower display. The user may enter a numerical password between 0 and 999 by turning the Adjust control. When the user re−enters the auxiliary menu, the password code
must be selected to gain access to the auxiliary menu. A failed attempt return the user to the
weld screen and a counter is incremented. A
counter in the program display shows the
number of incorrect attempts. The user has
five attempts to enter the correct password
code before being locked out of the auxiliary
menu, indicated by “LOCK” in the lower display . The power may be cycled to continue
welding but the user will remained locked out
of the auxiliary menu. Pressing the Program,
Sequence, upper display, and Set−up push
buttons simultaneously, the counter can be reset in the weld screen. Resetting the counter
is indicated by “CODE” in the upper display
and “RSET” in the lower display. Pressing the
Program, Sequence, upper display, and Set−
up push buttons simultaneously again will allow the user to reset the unit to the factory defaults, indicated by “WIPE” in the upper display. Resetting the unit will also turn off the
password code feature.
SECTION 6 − SETTING SEQUENCE PARAMETERS
6-1. Sequence Parameters In A Program
. For more information on
Sequence Push Button see
Section 5-11.
Sequence
If time is set to zero in Weld
sequence, welding continues until
gun trigger is released.
Parameters
Volts
IPM
1. Preflow
If time is set to zero in any timed
sequence except Weld, the
sequence is skipped.
Seconds
0-9.9
2. Run-In
X
3. Start
X
X
0.00-5.00
4. Weld
X
X
0-100.0
5. Crater
X
X
0-5.00
6. Burnback
X
0-0.25
7. Postflow
0-9.9
X = Setting available.
Weld Time
Crater
Time
Preflow
Time
Burnback
Time
Start
Time
Postflow
Time
Time
Burnback
Preflow
Trigger
Pressed
Run-In Start
Weld
Crater
Postflow Sequence
End
Trigger
Released
OM-1500-14 Page 25
SECTION 7 − SETTING DUAL SCHEDULE PARAMETERS
7-1. Optional Dual Schedule Switch Diagrams
1
1
1
DSS-9
2
2
1
2
DSS-8
3
1
2
TR
B
A
2
3
A
4
B
Notes
OM-1500-14 Page 26
4
Maint 2P (Maintained-Contact
2-Pole Switch)
Maint 1P (Maintained-Contact
1-Pole Switch)
. Will not function with trigger
hold and dual schedule. A
DSS-9 is recommended for
this application.
7-2. Diagnostics
1
2
3
2
3
LED3 On Right Side Motor
Control Board PC1
LED3 On Left Side Motor
Control Board PC101
LED3 On Dual Board PC70
. There
is a two-position DIP
switch S1 located on motor control boards PC1 and PC101.
These switches are factory-set
in the off position and must remain in that position for the unit to
operate correctly.
1
803 063-A
Left Side Motor Control Board PC101
. Note: The error messages
are shown on the upper
and lower displays to indicate specific errors. Explanations are in the text
below:
ERR
ERR
ERR
ERR
COM1
TRG1
TCH1
MTR1
Indicates a communication error.
Indicates a trigger
error.
Indicates a
tachometer error.
Indicates a motor
error.
Right Side Motor Control Board PC1
ERR
ERR
ERR
ERR
COM2
TRG2
TCH2
MTR2
Indicates a communication error.
Indicates a trigger
error.
Indicates a
tachometer error.
Indicates a motor
error.
Dual Board PC70
ERR
COM3
LED3-Related Error Indications
Error conditions are indicated by LED3 on
PC1, PC101, and PC70. To view LED3, turn
Off unit, remove wrapper, and turn unit On.
The LED blinks in a 2.5 second cycle. The
number of blinks in this period indicates the
type of error.
The priority of the errors is related to the number of blinks indicating the error. The more
blinks, the more severe the error (motor error
is top priority). A higher priority error overrides
a lower one (if a motor error and a communication error existed, the light would blink four
times for the motor error).
Since blink On time and blink Off time are
equal in a four-blink cycle, the four−blink sequence appears as a constant blink.
Indicates a
communication
error.
1 blink = Communication Error
2 blinks = Trigger Error
3 blinks = Tach Error
4 blinks = Motor Error
• The communication error occurs 2.5 seconds after a loss of communication between
the motor and the Front Panel board or Dual
board. The user may continue to weld with
this error.
• The trigger error occurs if the user has the
trigger held for more than two minutes without striking an arc (providing current override is not enabled), or if the user holds the
trigger past the postflow phase in a timed
weld. This error also occurs if the trigger is
held when the feeder is powered up. The error may be cleared by releasing the trigger.
• The tach error occurs 2 seconds after the
loss of tachometer feedback. The user may
continue to weld with this error. The motor
speed is regulated through the monitoring of
voltage and current.
• The motor error indicates that the motor
has been drawing too much current for too
long.
OM-1500-14 Page 27
7-3. Diagnostics For User Defined Options
1
2
Front Panel
Front Panel Board PC20
User Defined Shutdown Error
Messages (Additional hardware
required for these to be functional)
1
If OPT1 and/or OPT2 are enabled
without additional hardware setup,
the following error messages will be
displayed on the front panel meters.
OPT1 and/or OPT2 must be disabled.
. Refer to Section 5-12 for correct setup procedures.
2
803 198
ERR
ERR
OPT1
OPT2
Indicates a User Defined
Option Error
SECTION 8 − MAINTENANCE & TROUBLESHOOTING
8-1. Routine Maintenance
Y Disconnect power before maintaining.
3 Months
Clean and
tighten
weld
terminals.
Replace
unreadable
labels.
Replace
cracked
parts.
Check
14-pin cord.
Repair or
replace
cracked
weld
cable.
Check gas
hose and
fittings.
Check gun
cable.
6 Months
Blow out or vacuum
inside. During heavy
service, clean
monthly.
OM-1500-14 Page 28
Or
Clean
drive rolls.
8-2. Troubleshooting
Y Disconnect power before troubleshooting.
Trouble
Remedy
Wire feeds, shielding gas flows, but elec- Check interconnecting cord connections. If secure, check cord for continuity and repair or replace (see
trode wire is not energized.
Sections 4-5 and 4-6).
Wire feeder is on, meter(s) do not light Check and reset circuit breaker at welding power source.
up, motor does not run, gas valve and
welding power source contactor do not
pull in.
Electrode wire feeding stops or feeds er- Check gun trigger connection. See gun Owner’s Manual.
ratically during welding.
Check gun trigger. See gun Owner’s Manual.
Readjust hub tension and drive roll pressure (see Section 4-11).
Change to correct size drive roll (see Table 10-1).
Clean or replace dirty or worn drive roll.
Incorrect size or worn wire guides.
Replace contact tip or liner. See gun Owner’s Manual.
Remove weld spatter or foreign matter from around nozzle opening.
Have Factory Authorized Service Agency check drive motor or motor control board PC1.
Motor runs slowly.
Check for correct input voltage.
Wire does not feed until trigger is pulled, Check for a short between welding gun trigger leads and weld cable. Repair short or replace welding gun.
but continues to feed after trigger is released, and trigger hold is not on.
Gas valve in feeder is rattling loudly Check for a short between welding gun trigger leads and weld cable. Repair short or replace welding gun.
along with possible erratic or slow wire
feed speed.
Wire feeder power is on, displays light
up, but unit is inoperative.
Check welding gun trigger leads for continuity, and repair leads or replace gun.
OM-1500-14 Page 29
SECTION 9 − ELECTRICAL DIAGRAM
Figure 9-1. Circuit Diagram
OM-1500-14 Page 30
204 144-C
OM-1500-14 Page 31
SECTION 10 − PARTS LIST
. Hardware is common and
11
6
7
12
Fig 10-3
18
22
Fig 10-4
26
27
28
29
30
Fig 10-4
25
15
24
23
14
2
20
21
31
31
19
15
17
16
1
Fig 10-2
2
14
13
2
5
8
9
4
3
10
Fig 10-5
not available unless listed.
803 189-C
Figure 10-1. Main Assembly
OM-1500-14 Page 32
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Model
DS-12 DS-16
Figure 10-1. Main Assembly
. 1 . . . . . . . . . . . . . . . . See Note
. 2 . . . . . . . . . . . . . . . . . . 201 319
. 2 . . . . . . . . . . . . . . . . . . 201 320
. . . . PLG37,38,137,138 047 636
. . . . . . . . . . . . . . . . . . . . . . 079 739
. . . . . . . . . . . . . . . . . . . . . . 163 520
. 3 . . . . . . . . . . . . . . . . . . 139 600
. 3 . . . . . . . . . . . . . . . . . . 139 599
. 4 . . . . . . . . . . . . . . . . . . 600 324
. 5 . . . . . . . . . . . . . . . . . . 602 243
. 6 . . . . . . . . . . . . . . . . . . 602 213
. 7 . . . . . . . . . . . . . . . . . . 601 872
. 8 . . . . . . . . . . . . . . . . . . 080 947
. 8 . . . . . . . . . . . . . . . . . . 151 626
. 9 . . . . . . . . . . . . . . . . . . 132 053
10 . . . . . . . . . . . . . . . . . Fig 10-5
. 11 . . . . . . . . . . . . . . . . ♦149 838
. 11 . . . . . . . . . . . . . . . . ♦149 839
. 11 . . . . . . . . . . . . . . . . ♦078 264
. 11 . . . . . . . . . . . . . . . . ♦079 216
12 . . . . . . . . . . . . . . . . ♦075 078
12 . . . . . . . . . . . . . . . . ♦079 217
13 . . . . . . . . . . . . . . . . . Fig 10-3
14 . . . RC37,137 . . . . 047 637
. . . . . . . PLG45,145 . . . . 131 203
. . . . . . . PLG44,144 . . . . 167 640
. . . . . . . PLG46,146 . . . . 115 090
15 . . . . . . . . . . . . . . . . . . 203 314
. . . . . . . . . . . . . . . . . . . . . . 115 094
. . . . . . . . . . . . . . . . . . . . . . 080 328
. . . . . . . . . . . . . . . . . . . . . . 079 531
. . . . . . . . . . . . . . . . . . . . . . 604 571
16 . . . . . . . . . . . . . . . . . . 605 227
17 . . . . GS1,101 . . . . . 228 035
. . . . . . . PLG4,104 . . . . 136 810
18 . . . . . . . . . . . . . . . . . . 139 813
19 . . . . . . . . . . . . . . . . . . 139 816
20 . . . . . . . . . . . . . . . . . . 159 647
21 . . . . . . . . . . . . . . . . . . 159 646
22 . . . . . . . . . . . . . . . . . . 159 360
23 . . . . . . . . . . . . . . . . . . 156 243
24 . . . . . . . . . . . . . . . . . . 145 639
25 . . . . . . . . . . . . . . . . . . 134 834
26 . . . . . . . . . . . . . . . . . . 208 944
26 . . . . . . . . . . . . . . . . ♦208 945
27 . . . . . . . . . . . . . . . . . . 157 295
28 . . . . . . . . . . . . . . . . . . 604 612
29 . . . . . . . . . . . . . . . . . . 082 050
30 . . . . . . . . . . . . . . . . . . 201 776
30 . . . . . . . . . . . . . . . . ♦201 777
. . . . . . . . . . . . . . . . . . . . . . 149 322
31 . . . . . . . . . . . . . . . . . . 211 989
. . . Control Box, (Fig 10-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . Cable, Interconnecting (consisting of) . . . . . . . . . . . . . . . . . . . . . 2 . . . . 0
. . . Cable, Interconnecting (consisting of) . . . . . . . . . . . . . . . . . . . . . 0 . . . . 2
. . . . Connector & Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . . Connector, Circ Clamp Str Rlf Sz 17-20 Amp 206322-2 . . . . 2 . . . . 2
. . . . Cable, Port No. 18/14 8/C (order by ft) . . . . . . . . . . . . . . . . . 17Ft . . 21Ft
. . . Hose, Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 0
. . . Hose, Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 . . . . 2
. . . Cable, Weld Cop Strd No. 4/0 (order by ft) . . . . . . . . . . . . . . . . 26Ft . . 30Ft
. . . Washer, Flat Stl Std .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 . . . . 8
. . . Washer, Lock Stl Split .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . . 4
. . . Nut, Stl Hex Full .375-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . . 4
. . . Bracket, Spring Retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 0
. . . Bracket, Spring Retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 . . . . 1
. . . Screw, Cap Stl Hexhd .375-16 X 1.500 Lg . . . . . . . . . . . . . . . . . 4 . . . . 4
. . . Support, Hub & Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . Pipe Post, 4ft W/Base Or . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 0
. . . Pipe Post, 6ft W/Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 0
. . . Pipe Post, 4ft W/Base Or . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 . . . . 1
. . . Pipe Post, 6ft W/Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 . . . . 1
. . . Pipe Post, 4ft W/O Base Or . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . Pipe Post, 6ft W/O Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . Boom Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . Connector & Sockets (consisting of) . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . . Housing Plug + Pins, (service kit) . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . . Housing Plug Pins + Skts (service kit) . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . . Housing Plug + Pins, (service kit) . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . Cable,Trigger 20 In Boom/Detach (consisting of) . . . . . . . . . . . 2 . . . . 2
. . . . Housing Plug+Skts,(service kit) . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . . Rcpt W/Skts,Free Hanging . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . . Conn,Circ Cpc Clamp Str Rlf Size 11 .453od . . . . . . . . . . . . . 2 . . . . 2
. . . . Cable,Port No 18 4/C Type sjo nprn jkt re . . . . . . . . . . . . . . . . . . 2Ft
. . . Nut, Nyl Hex Jam .750npst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . Valve, 34VDC 1way .750-14 Thd 2mm Orf 100PSI . . . . . . . . . . 2 . . . . 2
. . . Housing Plug + Skts (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . Cover, Protector Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . Panel, Encl Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . Insulator, Motor Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . Clamp, Motor Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . Insulator, Screw Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 . . . . 8
. . . Clamp, Motor Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . Strip, Buna N Compressed Sheet .062 X 4.000sq . . . . . . . . . . 2 . . . . 2
. . . Hose, Sae .187 Id X .410 Od (order by ft) . . . . . . . . . . . . . . . . 3Ft . . 3Ft
. . . Drive Assy,Wire Rh Vertical 4 Roll W/Clamp&tach (Fig 10-4) . 1 . . . . 1
. . . Drive Assy,Wire Rh Vert 4 Roll Hi−speed W/Cl&tach (Fig 10-4) 1 . . . . 1
. . . Guide, Monocoil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . Screw, Set Stl Sch 8-32 X .125 Cup Point . . . . . . . . . . . . . . . . . 4 . . . . 4
. . . Liner, Monocoil Inlet Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . Drive Assy,Wire L Vertical 4 Roll W/Clamp&tach (Fig 10-4) . . 1 . . . . 1
. . . Drive Assy,Wire L Vert 4 Roll Hi−speed W/Cl&tach (Fig 10-4) 1 . . . . 1
. . . Clamp, Hose .405−.485clp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . . 4
. . . Fitting, W/Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
♦ OPTIONAL
Note: When ordering Control Box contact factory service department for proper number.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1500-14 Page 33
. Hardware is common and
not available unless listed.
9
8
7
1
11
10
12
13
14
15
9
2
4
6
3
25
16
5
17
24
8
23
19
18
20
21
22
803 200
Figure 10-2. Control Box
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-2. Control Box (Figure 10-1 Item 1)
... 1 ...............
.....................
... 2 ...............
... 3 ...............
. . . 4 . . . . PC21 . . . . .
. . . 5 . . . . PC20 . . . . .
. . . 6 . . . . . S1 . . . . . .
. . . 7 . . . . PC70 . . . . .
. . . 8 . . PC1,101 . . .
... 9 ...............
. . . 10 . . . . . . . . . . . . . . .
. . . 10 . . . . . . . . . . . . . . .
. . . 11 . . . . . . . . . . . . . . .
. . . 12 . . . . . . . . . . . . . . .
. . . 13 . . . . . . . . . . . . . . .
. . . 14 . . . . . . . . . . . . . . .
. . . 15 . . . PLG12 . . . .
. . . . . . . . . PLG52 . . . .
. . . . . . . . . PLG74 . . . .
. . . 16 . . RC40,140 . . .
. . . . . . . PLG34,134 . .
. . . . . . . PLG35,135 . .
. . . . . . . PLG36,136 . .
. . . 17 . . . . . . . . . . . . . . .
OM-1500-14 Page 34
204 722
134 464
206 764
200 153
200 693
210 683
111 997
220 903
217 898
030 170
000 527
047 838
201 228
139 041
163 519
079 739
141 162
174 823
115 093
047 637
136 810
131 204
115 094
010 494
. . Wrapper, Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Label,Warning General Precautionary Static&wire Fe . . . . . . . . . . . . . . 1
. . Panel, PC Card Front (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Overlay, Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Circuit Card Assy,Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Panel, Pc Card Display W/Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Switch, Rocker Spst 10A 250vac On-Off Visi Red Rock . . . . . . . . . . . . . 1
. . Circuit Card Assy, Dual W/Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Circuit Card Assy, Motor Control W/Program . . . . . . . . . . . . . . . . . . . . . . 2
. . Bushing,Snap−in Nyl .750 Id X 1.000 Mtg Hole . . . . . . . . . . . . . . . . . . . . 1
. . Blank, Snap−in Nyl .875 Mtg Hole Black . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Blank,Snap−in Nyl 1.000 Mtg Hole Black . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Cable, Power 16.5ft 8/c 2-14ga 6-18ga (consisting of) . . . . . . . . . . . . . . 1
. . . . Strain Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Cable, Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 Ft
. . . . Conn, circ cpc clamp str rlf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Housing Plug+Pins, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Housing Plug Pins+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Housing Rcpt+Skts,(service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . Bushing, Snap−in Nyl 1.375 Id X 1.750 Mtg Hole . . . . . . . . . . . . . . . . . . . 2
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-2. Control Box (Continued)
...
...
...
...
...
...
...
...
18
19
20
21
22
23
24
25
...............
...............
...............
...............
. . . S2,102 . . . .
. . . . S100 . . . . .
...............
...............
Dia.
Mkgs.
134 201
204 721
206 765
206 771
200 295
201 641
213 134
207 745
Part
No.
..
..
..
..
..
..
..
..
Stand-Off Support, PC Card .312/.375w/Post&lock .43 . . . . . . . . . . . . . .
Enclosure, Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Panel, Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nameplate, Miller Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch, Rocker Spdt 15A 12V (On)−Off−(On) . . . . . . . . . . . . . . . . . . . . . .
Switch, Rocker Spdt 15A 12V (On)−Off−(On) W/leds . . . . . . . . . . . . . . .
Knob, Encoder 1.670 Dia x .250 Id Push On W/Spring . . . . . . . . . . . . . .
Nameplate, Miller Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description
17
1
1
1
2
1
1
1
Quantity
Harness Connectors/Receptacles
. . . . . . . . PLG6,106 . . .
. . . . . . . PLG10,110 . .
. . . . . . . . . PLG72 . . . .
. . . . . . . . PLG4,104 . . .
. . . . PLG11, 21,71,111
. . PLG1,77,78,79,101
. . . . . PLG3,75,76,103
. . . . . . . . . PLG51 . . . .
. . . . . PLG7,27,67,107
. . . . . . . . . PLG73 . . . .
. . . . . . . . PLG17,70 . . .
. . . . . . . . PLG117 . . .
115 094
130 203
115 092
136 810
131 055
202 592
115 093
174 824
115 091
148 439
158 719
165 404
..
..
..
..
..
..
..
..
..
..
..
..
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Rcpt+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug Pins+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug Pins+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Rcpt+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
1
1
1
1
OM-1500-14 Page 35
14
23
22
21
20
17
15
19
16
15
14
13
12
18
11
10
25
1
30
2
3
4
29
5
6
28
27
not available unless listed.
24
26
7
8
9
. Hardware is common and
ST-142 306-H
Figure 10-3. Boom Assembly
OM-1500-14 Page 36
Item
No.
Part
No.
Description
Quantity
Model
DS-12 DS-16
Figure 10-3. Boom Assembly (Figure 10-1 Item 13)
. . . . . . 1 . . . . . . 010 313
. . . . . . 2 . . . . . . 010 910
. . . . . . 3 . . . . . . 079 622
. . . . . . 4 . . . . . . 079 621
. . . . . . 5 . . . . . . 079 667
. . . . . . 5 . . . . . . 080 812
. . . . . . 6 . . . . . . 079 632
. . . . . . 7 . . . . . . 079 665
. . . . . . 7 . . . . . . 080 811
. . . . . . 8 . . . . . . 079 664
. . . . . . 9 . . . . . . 139 633
. . . . . 10 . . . . . . 159 999
. . . . . 10 . . . . . . 160 513
. . . . . . 11 . . . . . . 080 947
. . . . . . 11 . . . . . . 151 626
. . . . . 12 . . . . . . 073 742
. . . . . 13 . . . . . . 073 741
. . . . . 14 . . . . . . 079 029
. . . . . 15 . . . . . . 075 462
. . . . . 16 . . . . . . 602 250
. . . . . 17 . . . . . . 079 020
. . . . . 18 . . . . . . 155 335
. . . . . 19 . . . . . . 149 858
. . . . . 19 . . . . . . 151 625
. . . . . 20 . . . . . . 150 258
. . . . . 21 . . . . . . 024 605
. . . . . 22 . . . . . . 075 101
. . . . . 23 . . . . . . 079 030
. . . . . 24 . . . . . +174 754
. . . . . . . . . . . . . . . 080 157
. . . . . 25 . . . . . . 174 688
. . . . . . . . . . . . . . . 142 804
. . . . . . . . . . . . . . . 134 327
. . . . . 26 . . . . . . 073 666
. . . . . 27 . . . . . . 047 224
. . . . . 28 . . . . . . 602 246
. . . . . 29 . . . . . . 010 493
. . . . . 30 . . . . . . 139 818
. . Pin, Cotter Hair .072 X 1.437 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Flat Stl Sae .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Shld .381 Id X .750 Od . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pulley, V Sgl Grv 7.750dia X 8.000p X .625 Bore . . . . . . . . . . . . . . . . . .
. . Pipe, Plstc .500 X 133.750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pipe, Plstc .500 X 181.750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bolt, U Stl .250-20 X .875 Wide X 1.375 Deep . . . . . . . . . . . . . . . . . . . .
. . Guide, Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Guide, Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Guide, Wire Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Liner, Monocoil 3/32-1/8 Wire X 15.687 . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Boom, Dual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Boom, Dual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Spring Retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Spring Retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pin, Clevis .750 Od X 2.156 Lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Clevis, .812 Yoke 6.062 Lg .750-16Thd . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Nut, Stl Hex Full Fnsh .750-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Shaft, Boom Counterbalance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Flat Stl Sae .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Nut, Stl Hex Elastic Stop .750-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pipe, Blk 3.000 X .875 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Spring, Cprsn 3.750 Od X .625 Wire X 36.000 . . . . . . . . . . . . . . . . . . . .
. . Spring, Cprsn 3.750 Od X .640 Wire X 36.000 . . . . . . . . . . . . . . . . . . . .
. . Retainer, Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bearing, Ball Thr Sgl Row .750 X 1.625 X .625 . . . . . . . . . . . . . . . . . . .
. . Nut, Stl Hex Special .750-16 X 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Lock Stl Ext Tooth .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Base, Swivel Boom (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Fitting, Grease 1/8npt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Bracket, Mtg Control Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Swingarc Caution Heavy Spring . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Warning General Precautionary . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bolt, Mach Stl Hexhd .750-16 X 2.750 . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Knob, T-bar .500-13Thd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Flat Stl Std .500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bushing, Snap-in Nyl .625 Id X .875mtg Hole . . . . . . . . . . . . . . . . . . . . .
. . Guard, Motor Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
6
2
2
2
0
8
2
0
2
2
1
0
1
0
1
1
2
1
2
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
4
6
2
2
0
2
10
0
2
2
2
0
1
0
1
1
1
2
1
2
1
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1500-14 Page 37
. Hardware is common and
16
not available unless listed.
22
14
17
See Table 10-1 For
Drive Roll & Wire Guide Kits
18
19
20
21
22
15
5
6
7
8
23
14
9
12
2
10
4
3
11
13
1
24
25
37
38
39
40
34
35
36
26
27
33
28
32
29
31
30
802 977-B
Figure 10-4. Drive Assembly, Wire
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Model
DS-12 DS-16
Figure 10-4. Drive Assembly, Wire (Figure 10-1 Items 26 and 30)
. . . 1 . . . . . . . . . . . . . . . 010 668
. . . 2 . . . . . . . . . . . . . . . 172 075
. . . 3 . . . . . . . . . . . . . . . 149 962
. . . 4 . . . . . . . . . . . . . . . 149 486
. . . 5 . . . . . . . . . . . . . . . 163 282
. . . 6 . . . . . . . . . . . . . . . 165 798
. . . 7 . . . . . . . . . . . . . . . 165 799
. . . 8 . . . . . . . . . . . . . . . 132 750
. . . 9 . . . . . . . . . . . . . . . 150 520
. . . 10 . . . . . . . . . . . . . . . 133 493
. . . 11 . . . . . . . . . . . . . . . 133 350
. . . 12 . . . M1,101 . . . . 201 230
. . . 12 . . . M1,101 . . . . 201 231
. . . . . . . . . . . . . . . . . . . . . 153 491
. . . . . . . . . . . . . . . . . . . . . 153 492
. . . . . . . . . . . . . . . . . . . . *153 493
OM-1500-14 Page 38
. . Screw, Cap Stl Sch .250-20 X 1.500 . . . . . . . . . . . . . . . . . . . . . . . .
. . Carrier, Drive Roll W/Components 24 Pitch . . . . . . . . . . . . . . . . . .
. . Spacer, Carrier Drive Roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pin, Rotation Arm Rocker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Nut, .250-28 Stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Spring, Pressure Arm Retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Flat .257 Id Stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Arm, Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Spacer, Rotation Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Ring, Retaining Ext .250 Shaft X .025thk . . . . . . . . . . . . . . . . . . . .
. . Pin, Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Motor, Gear 1/8hp 24vdc Standard Speed . . . . . . . . . . . . . . . . . .
. . Motor, Gear 1/8hp 24vdc High Speed . . . . . . . . . . . . . . . . . . . . . . .
. . . . Kit, Brush Replacement (consisting of) . . . . . . . . . . . . . . . . . . . .
. . . . . Cap, Brush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . Brush, Carbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
4
4
2
2
2
2
2
2
2
1
1
0
1
2
2
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
4
4
4
2
2
2
2
2
2
2
1
1
1
1
2
2
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Model
DS-12 DS-16
Figure 10-4. Drive Assembly, Wire (continued)
. . . . . . . . . . . . . . . . . . . . . 184 136 . . . . Kit, Brush Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 13 . . . . . . . . . . . . . . . 155 098 . . Kit, Cover Motor Gearbox (consisting of) . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . . 153 550 . . . . . Cover, Motor Gearbox (consisting of) . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . . 155 099 . . . . . . . Gasket, Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . . 155 100 . . . . . . . Screw, Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 . . . . 5
. . . . . . . . . . . . . . . . . . . . . 154 031 . . . . . Spacer, Locating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . . . . . . . . . . . . . . . . . . . 133 493 . . . . Ring, Rtng Ext .250 Shaft Grv X .025Thk . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . . 203 642 . . Pressure Arm,R & Vert L 4 Roll (consisting of) . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . . 203 631 . . Pressure Arm,S/L & Vert S/R 4 Roll (consisting of) . . . . . . . . . . . 1 . . . . 1
. . . 14 . . . . . . . . . . . . . . . 203 461 . . . . Washer, Flat Indicator Spring Tension . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . 15 . . . . . . . . . . . . . . . 182 415 . . . . Pin, Cotter Hair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 16 . . . . . . . . . . . . . . . 203 640 . . . . Knob, W/Extension Short Pressure Arm . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 17 . . . . . . . . . . . . . . . 182 156 . . . . Spring, Cprsn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . 18 . . . . . . . . . . . . . . . 182 155 . . . . Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . 19 . . . . . . . . . . . . . . . 132 746 . . . . Bushing, Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . 20 . . . . . . . . . . . . . . . 203 633 . . . . Shaft, Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 21 . . . . . . . . . . . . . . . 203 632 . . . . Carrier, Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 22 . . . . . . . . . . . . . . . 133 739 . . . . Washer, Flat Buna .375 Id X .625 Od X .062Thk . . . . . . . . . . . 2 . . . . 2
. . . 23 . . . . . . . . . . . . . . . 203 637 . . . . Knob, W/Extension Long Pressure Arm . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 24 . . PC51,151 . . . 201 225 . . Circuit Card, Digital Tach (consisting of) . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . PLG5 . . . . . 131 204 . . . . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . . 604 311 . . . . Grommet, Rbr .250 Id X .375Mtg Hole . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 25 . . . . . . . . . . . . . . . 132 611 . . Optical Encoder Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . . 603 115 . . Weather Stripping, Adh .125 X .375 . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 26 . . . . . . . . . . . . . . . 134 834 . . Hose, Sae .187 Id X .410 Od (order by ft) . . . . . . . . . . . . . . . . . . . . . 2 Ft
. . . 27 . . . . . . . . . . . . . . . 149 959 . . Fitting, Brs Barbed M 3/16Tbg X .312-24 . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 28 . . . . . . . . . . . . . . . 179 265 . . Adapter, Gun/Feeder Lh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 28 . . . . . . . . . . . . . . . 179 264 . . Adapter, Gun/Feeder Rh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 29 . . . . . . . . . . . . . . . 108 940 . . Screw, Cap Stl Hexwhd .250-20 X .750 . . . . . . . . . . . . . . . . . . . . . 4 . . . . 4
. . . 30 . . . . . . . . . . . . . . . 604 538 . . Washer, Flat Stl Sae .312 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 31 . . . . . . . . . . . . . . . 151 437 . . Knob, Plstc T 1.125 Lg X .312-18 X 1.500 Bar . . . . . . . . . . . . . . . 1 . . . . 1
. . . 32 . . . . . . . . . . . . . . . 151 290 . . Screw, Hexwhd-Slt Stl Slffmg 10-32 X .500 . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . 33 . . . . . . . . . . . . . . . 179 277 . . Cover, Drive Roll (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . . 196 956 . . . . Label, Warning Electric Shock And Pinch . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 34 . . . . . . . . . . . . . . . 601 872 . . Nut, Stl Hex Full .375-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 35 . . . . . . . . . . . . . . . 602 213 . . Washer, Lock Stl Split .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 36 . . . . . . . . . . . . . . . 602 243 . . Washer, Flat Stl .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 37 . . . . . . . . . . . . . . . 601 966 . . Screw, Cap Stl Hexhd .375-16 X 1.250 . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 38 . . . . . . . . . . . . . . . 167 387 . . Spacer, Locating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . 39 . . . . . . . . . . . . . . . 168 825 . . Drive, Pinion 40t 24p .376 Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 40 . . . . . . . . . . . . . . . 133 308 . . Ring, Retaining Ext .375 Shaft X .025Thk . . . . . . . . . . . . . . . . . . . 1 . . . . 1
*Recommended Spare Parts.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1500-14 Page 39
1
. Hardware is common and
2
3
not available unless listed.
4
5
6
7
8
13
7
12
6
9
10
11
ST-081 760-C
Figure 10-5. Support, Hub & Reel
Item
No.
Part
No.
Description
Quantity
Figure 10-5. Support, Hub and Reel (Figure 10-1 Item 10)
. . . 1 . . . . 058 427
. . . 2 . . . . 136 684
. . . 3 . . . . 605 941
. . . 4 . . . . 010 233
. . . 5 . . . . 057 971
. . . 6 . . . . 010 191
. . . 7 . . . . 058 628
. . . 8 . . . . 058 428
. . . 9 . . . . 080 393
. . . 10 . . . ♦108 008
. . . 11 . . . . 124 900
. . . 12 . . . +168 104
. . . . . . . . . . 166 594
. . . 13 . . . . 168 103
. . Ring, Retaining Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Nut, Stl Slflkg Hex Reg .625-11 W/Nyl Insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Flat Stl .640 Id X 1.000 Od X 14ga Thk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Spring, Cprsn .970 Od X .120 Wire X 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Flat Stl Keyed 1.500Dia X .125Thk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Fbr .656 Id X 1.500 Od X .125Thk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Brake Stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Hub, Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Support, Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Reel, Wire 60 Lb (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Support, Reel Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Retainer, Spool Support (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . Label, Caution Falling Wire Reel Can Cause Damage . . . . . . . . . . . . . . . . . . . . . .
. . . . Nut, Spanner Retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
2
2
2
4
4
2
1
2
1
1
1
1
♦ OPTIONAL
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1500-14 Page 40
Fraction
Intermediate
Guide
Wire Size
Inlet
Guide
Table 10-1. Drive Roll and Wire Guide Kits
150 993
149 518
151 024
087 130
Metric
.023-.025 in. 0.6 mm
V-GROOVE
4 Roll
Kit
Drive
Roll
U-GROOVE
VK-GROOVE
4 Roll
Kit
Drive
Roll
4 Roll
Kit
Drive
Roll
151 036
072 000
151 052
132 958
UC-GROOVE
4 Roll
Kit
Drive
Roll
.030 in.
0.8 mm
150 993
149 518
151 025
053 695
.035 in.
0.9 mm
150 993
149 518
151 026
053 700
.040 in.
1.0 mm
150 993
149 518
161 189
053 696
.045 in.
1.1/1.2 mm 150 994
149 519
151 027
053 697
151 037
053 701
151 053
132 957
151 070
083 489
.052 in.
1.3/1.4 mm 150 994
149 519
151 028
053 698
151 038
053 702
151 054
132 956
151 071
083 490
151 029
053 699
151 039
053 706
151 055
132 955
151 072
053 708
151 056
132 959
1/16 in.
(.062 in.)
1.6 mm
150 995
149 520
.068-.072 in. 1.8 mm
150 995
149 520
5/64 in.
(.079 in.)
2.0 mm
150 995
149 520
151 040
053 704
151 057
132 960
151 073
053 710
3/32 in.
(.094 in.)
2.4 mm
150 996
149 521
151 041
053 703
151 058
132 961
151 074
053 709
7/64 in.
(.110 in.)
2.8 mm
150 996
149 521
151 042
053 705
151 059
132 962
151 075
053 711
1/8 in.
(.125 in.)
3.2 mm
150 997
149 522
151 043
053 707
151 060
132 963
151 076
053 712
Each Kit Contains An Inlet Guide, Intermediate Guide, And 045 233 Antiwear Guide With 604 612 Setscrew 8-32 x .125, Along
With 4 Drive Rolls.
2 Kits Required For Dual Models.
S-0549-D
OM-1500-14 Page 41
Effective January 1, 2006
(Equipment with a serial number preface of “LG” or newer)
Warranty Questions?
Call
1-800-4-A-MILLER
for your local
Miller distributor.
Your distributor also gives
you ...
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY − Subject to the terms and conditions
* Induction Heating Coils and Blankets, Cables, and
below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to
Non-Electronic Controls
its original retail purchaser that new Miller equipment sold after
* APT & SAF Model Plasma Cutting Torches
the effective date of this limited warranty is free of defects in
* Remote Controls
material and workmanship at the time it is shipped by Miller. THIS
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
* Accessory (Kits)
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
* Replacement Parts (No labor)
WARRANTIES OF MERCHANTABILITY AND FITNESS.
* Spoolmate Spoolguns
Within the warranty periods listed below, Miller will repair or
* Canvas Covers
replace any warranted parts or components that fail due to such
defects in material or workmanship. Miller must be notified in
writing within thirty (30) days of such defect or failure, at which
time Miller will provide instructions on the warranty claim
procedures to be followed.
Miller shall honor warranty claims on warranted equipment listed
below in the event of such a failure within the warranty time
periods. All warranty time periods start on the date that the
equipment was delivered to the original retail purchaser, or one
year after the equipment is sent to a North American distributor
or eighteen months after the equipment is sent to an
International distributor.
1.
5 Years Parts — 3 Years Labor
2.
3 Years — Parts and Labor
*
*
*
*
*
*
*
*
*
3.
Original main power rectifiers
Transformer/Rectifier Power Sources
Plasma Arc Cutting Power Sources
Process Controllers
Semi-Automatic and Automatic Wire Feeders
Inverter Power Sources (Unless Otherwise Stated)
Water Coolant Systems (Integrated)
Intellitig
Engine Driven Welding Generators
(NOTE: Engines are warranted separately by the
engine manufacturer.)
1 Year — Parts and Labor Unless Specified
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Motor Driven Guns (w/exception of Spoolmate
Spoolguns)
Positioners and Controllers
Automatic Motion Devices
RFCS Foot Controls
Induction Heating Power Sources, Coolers, and
Electronic
Controls/Recorders
Water Coolant Systems (Non-Integrated)
Flowgauge and Flowmeter Regulators (No Labor)
HF Units
Grids
Spot Welders
Load Banks
Arc Stud Power Sources & Arc Stud Guns
Racks
Running Gear/Trailers
Plasma Cutting Torches (except APT & SAF
Models)
Field Options
(NOTE: Field options are covered under True Blue®
for the remaining warranty period of the product they
are installed in, or for a minimum of one year —
whichever is greater.)
Bernard-Branded Mig Guns (No Labor)
Weldcraft-Branded TIG Torches (No Labor)
Subarc Wire Drive Assemblies
4.
6 Months — Batteries
5.
90 Days — Parts
*
MIG Guns/TIG Torches and Subarc (SAW) Guns
Miller’s True Blue® Limited Warranty shall not apply to:
1.
Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, slip rings, relays
or parts that fail due to normal wear. (Exception:
brushes, slip rings, and relays are covered on Bobcat,
Trailblazer, and Legend models.)
2.
Items furnished by Miller, but manufactured by others, such
as engines or trade accessories. These items are covered
by the manufacturer’s warranty, if any.
3.
Equipment that has been modified by any party other than
Miller, or equipment that has been improperly installed,
improperly operated or misused based upon industry
standards, or equipment which has not had reasonable and
necessary maintenance, or equipment which has been
used for operation outside of the specifications for the
equipment.
MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS
TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4)
payment of or credit for the purchase price (less reasonable
depreciation based upon actual use) upon return of the goods at
customer’s risk and expense. Miller’s option of repair or
replacement will be F.O.B., Factory at Appleton, Wisconsin, or
F.O.B. at a Miller authorized service facility as determined by
Miller. Therefore no compensation or reimbursement for
transportation costs of any kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT,
INDIRECT,
SPECIAL,
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY
OTHER LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND
ANY
IMPLIED
WARRANTY,
GUARANTY
OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS
PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION
OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING,
INCLUDING
ANY
IMPLIED
WARRANTY
OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT
FURNISHED BY MILLER IS EXCLUDED AND DISCLAIMED
BY MILLER.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary from
state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein,
and to the extent that they may not be waived, the limitations and
exclusions set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available,
but may vary from province to province.
miller_warr 2006−01
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
For Service
Contact a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
Replacement Parts
Training (Schools, Videos, Books)
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
Welding Process Handbooks
To locate a Distributor or Service Agency visit
www.millerwelds.com or call 1-800-4-A-Miller
Contact the Delivering Carrier to:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.
PRINTED IN USA
© 2006 Miller Electric Mfg. Co. 2006−01
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
International Headquarters−USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
European Headquarters −
United Kingdom
Phone: 44 (0) 1204-593493
FAX: 44 (0) 1204-598066
www.MillerWelds.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising