Miller MMT-200A1 GUN User manual

June1976
FORM:
OM-1018
Effective With Style No. HD-1A
FLE COPY
RETURN TO FOLDER
MODEL
STOCK NO.
MMT-200A1 GUN
CONDUIT ASSEMBLY
.030 WIRE lOFT
056 505
.035 WiRE lOFT
056 506
.045 WIRE lOFT
056 507
.030 WIRE
056 493
15FT
.035 WIRE 15FT
056 494
.045 WIRE
056 495
15FT
MONOCOIL ASSEMBLY
.030 WIRE
MODEL/STOCK NO.
SERIAL/STYLE NO.
OWNERS
10 FT
056 545
.035 WIRE
10 FT
056 546
.045 WIRE
10 FT
056 547
.030 WIRE
15 FT
057 028
.035 WIRE 15 FT
057 029
045 WIRE 15 FT
057 030
DATE PURCHASED
MANUAL
MILLER ELECTRIC MFG. CO.
APPLETON, WISCONSIN, USA 54911
ADDITIONAL COPY
PRICE 30 CENTS
NWSA CODE NO. 4579
,,INTC0
LIMITED WARRANTY
MILLER Electric Mfg. Co., Appleton, Wisconsin, warrants a~I new equipment to be free from defects in
material and factory workmanship for the periods indicated below, provided the equipment is installed and
operated according
to
manufacturers instructions.
C
CD
C
CD
C
MILLER Electric
~
Mfg. Co.s obligation, under this warranty, is expressly limited to replacing or repairing
defective
part or correcting any manufacturing defect without charge during the warranty period if
any
MILLERS
inspection confirms the existence of such defects. MILLERS option of repair or replacement
~
will be f.o.b.
no
factory at Appleton, Wisconsin or f.o.b. a MILLER authorized service facility, and therefore
compensation for transportation costs of any kind will be allowed.
c
C)
C)
C)
C)
The warranty
C
)
period, beginning
the date of sale to the
original purchaser-user
of the
equipment, will
be
as
C
1.
Arc welders, power sources, and components
1 year
2.
Original main power rectifiers
20E, 20K, and all welding guns.
90 days
3.
~
on
follows:
4.
All other Millermatic Feeders
5.
All
engines
3 years
(unconditionally)
1 year
.-
1 year
Warranties are covered by the engine manufacturers, subject to their procedures and to be
through their authorized local Service Stations or agencies. No warranty will be made in respect
accessories, such being subject to the warranties of their respective manufacturers.
handled
MILLER Electric
accruing
Engine
directly
or
Mfg. Co. will not be liable for any loss or consequential damage
indirectly from the use of equipment covered in this warranty.
supersedes all previous MILLER warranties and is exclusive with
expressed or implied.
This warranty
warrantie~
no
or
expense
to
trade
other guarantees
or
BE
ERRATA SHEET
After this manual
was
printed, refinements
in
equipment design occurred. This sheet lists exceptions
to
data
appearing
later in
this manual.
FILE COPY
RETURN TO FOLDER
Effective With Style No. HJ-6
Item
Part No. Listed
Replaced With
No.
In Parts List
Part No.
030 403
030 403
14
030404
14
057 782
21
057 782
057 783
21
36
603 886
Deleted
37
604 874
Deleted
39
603 887
Deleted
40
604311
Deleted
41
057027
053132
44
602 087
Deleted
45
601 845
Deleted
46
056 847
Description
Quantity
(10 ft.) (consisting of) or
power (15 ft.) (consisting of)
CORD, switch (10 ft.) (consisting of) or
CORD, switch (15 ft.) (consisting of)
1
RELIEF,strain
1
CABLE,
CABLE,
power
1
1
1
Deleted
059 294
BLOCK, mounting switch
NUT, speed push on type .320
SPRING, compression
059 293
RIVET, steel
059 258
059 290
1
-
-
-
ID
-
solid flat hd 7/32
x
1
7/16 OD
I
x
1
1-1/4
REPLACEMENT PARTS.
SURE TO PROVIDE STOCK, MODEL, AND STYLE NUMBERS WHEN ORDERING
.1
OM-lOl8PageA
SECTION 1
Figure
1-1.
INTRODUCTION
-
Cable And
Cooling
Hose Length
Method
10
Air
15
Air
1-1. Specifications
The short circuiting transfer mode of gas metal-arc welding is
consumable electrode welding process in which the elec
trode, the arc, and the weld puddle are contained in a protec
GENERAL
a
This manual has been prepared especially for use in familiar
izing personnel with the design, installation, operation, main
tenance, and troubleshooting of this equipment. All informa
tion presented herein should be given careful consideration
assure optimum performance of this equipment.
tive atmosphere of shielding gas. Consumable welding wire is
automatically and continuously fed into the arc. High current
densities permit the use of the high welding speeds; gas
shielding prevents atmospheric contaminations, thus eliminat
to
the need for fluxes that would result in
ing
Instructions in this manual are confined to
its being used in conjunction with the control/feeders of the
same manufacturer.
Gun
If the
Gun
ordered
was
for, and going
to be
installed
on
a
wire control/feeder other than the same manufacturer, sepa
rate Installation instructions will be supplied. A separate in
1-4.
The
following definitions apply to CAUTION, IMPORTANT,
and NOTE blocks found throughout this manual:
~t~~UflI.J~II1
RECEIVING-HANDLING
Under this heading, installation, operating, and main
tenance
this equipment, clean all packing material
unit and carefully inspect for any damage
that may have occurred during shipment. Any claims for loss
or damage that may have occurred in transit must be filed by
the purchaser with the carrier. A copy of the bill of lading
Prior
to
installing
not
from around the
and
freight bill
occasion
to
will be furnished by the carrier
on
request if
file claim arises.
carefully followed may
SECTION 2
-
a
hazard
to
U
if
per
heading, installation, operating, and main
procedures or practices will be found that if
carefully followed may result in damage to equip
this
Under
not
ment.
U
This model gun is designed specifically for the gas metal-arc
electrode welding process. It is air-cooled and
sembled and ready for operation with the specific wire size
components ordered. Only minor changes of parts in the gun
and wire control/feeder are necessary to convert to 0.030 and
0.035 or 0.045 inch diameter hard wire.
create
that
tenance
NOTE
consumable
rated at 200 amperes dcrp at 100 percent duty cycle using
CO2 shielding gas. The gun is shipped from the factory as
practices will be found
r=-~
I
DESCRIPTION
procedures
or
sonnel.
When requesting information concerning this equipment, it is
essential that Model Description and/or Stock Number and
Serial (or Style) Numbers of the equipment be supplied.
1-3.
removal.
SAFETY
struction manual is included with the control/feeder for its
particular maintenance and operation.
1-2.
slag
Installation
I
I
heading, explanatory statements will be
need special emphasis to obtain the most
efficient operation of the equipment.
Under this
found that
I
U
INSTALLATION
Gear
Assembly
Connection
Outlet Guide
Weld Cable Terminal
Figure 2-1. Gun To Control/Feeder Connections
OM-1018 Page 1
2.
sour~
Ensure that the welding power
completely
shut down and that power is removed froni the
prior to installing the gun.
3.
4.
_feeder/control
2-1.
Thread the electrode wire
through
the drive roll
of
the
control/feeder so it extends about 3 inches beyond the
outlet guide hole.
CAUTION
Close and
the gear
secure
Slide the outlet
guide
cover.
over
the wire and into the drive roll
assembly housing.
GAS CONNECTIONS
5.
(Figure 2-1)
Ensure that the flat side of the outlet guide is
facing
the
set screw.
Connect the gas hose from the gun to the gas connection
the control/feeder. This fitting has a right hand thread.
on
IMPORTANT
2-2.
CONTROL SWITCH RECEPTACLE
The outlet guide should be positioned as close as pos
sible to the drive rolls without touching them. This
gives the maximum column wire strength thus eliminat
prong twistlock cap from the gun control
the control switch receptacle on the control/
Twist in a clockwise direction to lock the cap in
Insert the
cable
(Figure 2-1)
two
into
feeder.
position.
2-3.
WELD CABLE CONNECTIONS
Connect
terminal
2-4.
the
weld cable from
the control/feeder.
on
the
(Figure 2-1)
gun
OUTLET GUIDE CONNECTIONS
the
to
~
weld
ing
waves
any
time
U
in the wire. When more pressure is applied at
the clearance should be rechecked on all
guides.
I
cable
(Figure 2-1)
6.
Position the outlet guide as close
touching them.
as
possible
to
the drive
rolls without
1.
Ensure that proper size components are installed in the
assembly and the control/feeder for the wire size
being used (refer to respective parts list).
gun
SECTION 3
3-1.
7.
Tighten
the locking
screw.
SEQUENCE OF OPERATION
-
GAS METAL ARC WELDING (GMAW)
Ensure that proper electrical connections have been
made to the welding power source and the control/
feeder (refer to the respective Owners Manuals).
1.
~:peed
C
better to have
ra te too f ast than
If the wire feed rate is too slow upon initial
welding, the wire may burn back into the contact
too slow.
Ensure that the proper
the control/feeder.
2.
3.
shielding gas is connected
to
tube, thus damaging it.
Ensure that the welding wire has been properly
threaded and that correct initial tensions have been
set on the control/feeder (refer to the control/feeder
Owners Manual).
4.
Turn
5.
Place controls on the control/feeder in
positions for the welding set up.
6.
Energize the control/feeder (the welding power source
must be energized if the control/feeder power input is
connected to the welding power source).
on
the
shielding gas supply.
10.
the
welding
lever
power
source
is
on the welidng power source in the
required position for the welding set up (refer to weld
ing power source Owners Manual).
-
11.
the
Energize
the
welding
power
source.
required
CAUTION
Prior to weling, i:is imperative that pprotective
clothing (welding coat and gloves) and eye protection
(glasses and/or welding helmet) be put on. Failure to
comply may result in serious or permanent bodily
damage.
CAUTION
If
Place the controls
ene~ed
and
the
gun is depressed, open circuit
voltage will be present on the welding wire and any
metal part making contact with it.
switch
on
the
welding wire and all metal parts in contact with it
energized while welding. Do not touch the welding
wire or any metal part making contact with it.
The
are
NOTE
When
installing
new
equipment,
or
after
prolonged
shutdown, allow shielding gas to flow continuously for
at least one minute prior to welding in order to purge
the shielding gas line. Place the wire speed Control to
the minimum
while
setting
to
avoid wasting the
welding
wire
12.
13.
Hold the end of the gas nozzle approximately
from the workpiece.
Press the switch lever on the gun handle. Gas will start
flow, wire will start to feed and the arc will be
established. If wire slippage is noticed, tighten drive
to
purging.
pressure adjustment 1/4 turn at
page stops. Do not over tighten.
roll
7.
Press
lever
8.
the
on
1/2
button
(if applicable)
or
the switch
purge
the gun handle to purge the gas line.
Actuate the switch on the gun handle to run the wire
beyond the end of the gas nozzle (if applicable).
Cut the wire off approximately 1/4 to 3/8 from the
Ensure
nozzle,
shut
a
time until slip
out
that the
and
down
welding
that
feeder/control prior
9.
Page 2
speed control on the control/feeder
slightly in excess of anticipated wire speed.
Set
the
wire
adjustment.
to
is completely
from the
drive roll pressure
source
power
power
is
removed
performing
3-2.
SHUTTING DOWN
IMPORTANT
1.
Turn off the
shielding
Whenever drive roll pressure is adjusted inlet and out
let guide clearance must be rechecked.
I
If
welding
After the controls on the welding power source and
the control/feeder have been adjusted for normal oper
ation, the control/feeder and welding power source
will function automatically whenever the gun switch is
depressed. Releasing the gun switch lever will extin
guish the arc and cause wire feed and gas flow to stop.
-
2.
4-1.
or
associated
performed in
a
confined area, failure
to
the
Deenergize the control/feeder and
the
welding
power
MAINTENANCE
Ensure that the welding power source is completely
down and that power is removed from the
feeder/control prior to attempting maintenance work
this gun
off
source.
4.
Repair or replace as required all hose and cabling; give
particular attention to frayed and cracked insulation and
areas where it enters equipment.
5.
Remove grease and grime from
from electrical parts and cables.
6.
Blow out the casing with compressed air when changing
wire. This removes any metal chips and dirt that may have
accumulated.
shut
on
is
shielding gas supply could result in a
build-up of gas fumes, thereby endangering personnel
re-entering the welding area.
turn
SECTION 4
source.
rtUl.XI,
I
14.
gas at the
equipment.
components;
moisture
INSPECTION AND UPKEEP
4-2.
Usage and shop conditions
of maintenance required.
Inspect
1.
gun
tighten, repair
will determine
for broken areas, cracks and
and replace as required.
loose
weld spatter or foreign
which may accumulate around the nozzle orifice.
Carefully
2.
remove
CHANGING WIRE SIZES (Conduit)
(Figure 4-1)
frequency and type
any
parts;
Ensure that the
down and
shut
matter
control/feeder
welding
that
prior
feeder components,
to
or
is completely
from the
source
power
power
is
changing
removed
the
wire, control/
gun components.
Remove any accumulation around the switch.
3.
16
Conduit Wire Guide Kit
15
TC-056 502
4
~
5
17
18
~~ ~
19
12
~
____
Monocoii Wire Guide Kit
5-057 176
Figure 4-1. Wire Guide Kit Installation
OM-1018 Page 3
Each time the wire size is changed, the gun and control/
feede r must be adapt ed for use with the ne w size wire.
20.
4-3.
TW
ll~
If the gun is equipped for .030 or .035 wire and it is
to convert from one of these wire sizes to the
other, only the contact tube (item 4, Figure 4-1) will
have to be changed. However, if the gun is equipped
for .030 or .035 wire and it is desired to convert to
.045 wire (or vice versa), all of the following steps will
1
Install
guide (12) into control/feeder
welding operations.
outlet
ceed with
CHANGING WIRE SIZES (Monocoil)
and pro
(Figure 4-1)
Each time the wire size is changed, the gun and control/
feeder must be adapted for use with the new size wire.
desired
have to be
L.
performed.
J
NOTE
If the gun is equipped for .030 or .035 wire and it is
desired to convert from one of these wire sizes to the
I
Contact tube (item 4, Figure 4.1) will
have to be changed. However, if the gun is equipped
for .030 or .035 wire and it is desired to convert to
.045 wire (or vice versa), all of the following steps will
other, only the
1.
Cut the weld bead knob off the end of the
wire at the gun nozzle (2).
2.
Loosen the outlet guide locking screw and pull
outlet guide from the control/feeder (Figure 2-1).
3.
Cut the welding wire where it enters the outlet guide
(12). Pull the wire Out of the conduit (9) from the end
with the outlet guide.
4.
Remove nozzle (2). contact tube (4) and contact tube
adapter (5) from head tube (16).
5.
Slide insulating band (3) off of gun and
head screw (13).
welding
the
1.
2.
6.
Pull
handle
flat
to
avoid
8.
(6) and pull
(8) from head tube (16).
Loosen set screw
guide
guide locking
outlet
4.
screw
and pull
(Figure
from the control/feeder
welding
the
2-1).
Cut the welding wire where it enters the outlet guide
(12). Pull the wire out of the monocoil assembly from
guide.
Remove bolt (11) and strain relief (10).
jamming.
5.
7.
the
Loosen
the end with the outlet
(14) back about six inches. Pull switch
along with handle (14)
wires back
Cut the weld bead knob of f the end of the
wire at the gun nozzle (2).
outlet
3.
remove
performed.
have to be
I
Out conduit connector
Remove nozzle (2), contact tube (4) and Contact tube
(5). Install new items in reverse order just
adapter
given.
Unscrew conduit connector (8) from conduit assembly
(9) and pull conduit assembly (9) Out of gun handle
6.
Pull off insulator band (3) and
remove
flat head
screw
(13).
(14).
9.
Remove screw (11) from outlet
strain relief (10).
10.
Unscrew outlet
11.
Install
12.
new
Secure
guide (12) from
outlet
strain
guide (12)
relief
(10)
guide (12)
onto conduit
to
Pull handle (14) back about six inches. Pull switch
wires back along with handle (14) to avoid jamming.
8.
Remove
conduit (9).
outlet
(9).
guide (12)
guide (12)
outlet
9.
connector
with
10.
Insert the conduit (9) in
monocoil
Loosen set screw (6) in head tube (16) and pull Out
monocoil connector (17).
Loosen set screw on
liner
monocoil
monocoil liner (18).
Out
13.
and
(19).
(11).
screw
7.
and pull off
through the bottom of handle
monocoil connector (17), pull
install
and
proper size
(18)
(14).
11.
14.
Remove 0
install
Ring (15)
Install new monocoil cOnnector (19).
from the old connector (8) and
on new connector
12.
(8).
Remove
install
15.
Secure
new
conduit connector
(8)
onto
13.
Insert
Insert the head tube liner (7) into conduit connector
and insert into head tube (16). Secure with set
(8)
17.
15.
Position
(14)
screw
onto
on
(17) into head tube
(6).
head tube (16) and
secure
(13).
band
insulator
guide (12)
Connector
set screw
13)
over
screw
(13).
Install
monocoil connector (19).
(13).
18.
Install contact tube adapter (5) onto head, tube (16)
and contact tube (41 onto adapter (5).
19.
Install nozzle (2) onto insulator
(1).
Install
secure
17.
4
with
Position handle
outlet
16.
Page
secure
with flat head
Slide handle (14) Onto head tube (16) and secure with
flat head screw (13). Slide insulating band (3) over
screw
14.
(6).
(18) and
liner
(16) and
screw
(17).
the conduit
(9).
16.
the old connector (17) and
Ring from
the 0
on new connector
strain
with
(10)
(11).
relief
screw
onto
guide (12)
and
control/feeder
and
outlet
outlet guide
Install
(12) into
proceed with welding operations.
June 1976
FORM:
OM-1018
Effective With Style No. HD.1A
MODEL
STOCK NO.
MMT-200A1 GUN
CONDUIT ASSEMBLY
.O3OWIRE lOFT
056 505
.O35WIRE
lOFT
056 506
.045 WIRE
lOFT
056 507
.030 WIRE
15FT
056 493
.035 WIRE
15FT
056 494
.045 WIRE
15FT
056 495
MONOCOIL ASSEMBLY
MODEL/STOCK NO.
SERIAL/STYLE NO.
lOFT
056 545
.035 WIRE
lOFT
056 546
.045 WIRE
lOFT
056 547
.030 WIRE
15 FT
057 028
.035 WIRE
15 FT
057 029
.045 WIRE
15 FT
057 030
DATE PURCHASED
PARTS LIST
MILLER ELECTRIC MFG. CO.
APPLETON, WISCONSIN, USA 54911
NWSA CODE NO. 4579
.030 WIRE
All Other Part Numbers
Correspond With Parts
In Exploded View
Shown
1
TA-057 098
.5
Field
Switch Assembly, with housing
Replacement For Item 33 (057 098)
4
50
51
20
23
22~,
21
TC-056 502
26
Figure A
QM-1018 Page 1
Exploded View Of Gun Assembly
Quantity
Moel
Conduit
Item
Factory
No.
Part No.
Figure
A
1
058 348
2
058 292
3
054 572
4
057176
4
057179
4
057177
4
057180
4
057178
4
057181
4
057184
4
057187
4
057185
4
057188
4
057186
4
057189
5
054 242
5
054183
5
054157
6
054 158
7
056 075
7
056 076
8
058174
Description
Monocoil
1.2MM
.8MM
.9MM
1.2MM
.8MM
.9MM
.031
.035
.047
.031
.035
.047
.030
.035
.045
.030
.035
.045
Exploded View Of Gun Assembly
1
1
1
1
1
1
1
1
1
1
1
~.1
1
1
1
1
1
10
056653
11
057083
11
056741
12
602090
INSULATOR, nozzle w/retaining ring
NOZZLE, slip-on
BAND, rubber 1-1/8 ID x 3/64 wall x 3/4
KIT, guide wire .030 10 ft or
KIT, guide wire .030 15 ft (See Fig. B Page 4)
KIT, guide wire .035 lOft or
KIT, guide wire .035 15 ft (See Fig. B Page 4)
KIT, guide-wire .045 lOft or
KIT, guide wire .045 15 ft (See Fig. B Page 4)
KIT, guide wire .030 10 ft or
KIT, guide wire .030 15 ft (consisting of)
KIT, guide wire .035 10 ft or
KIT, guide wire .035 15 ft (consisting of)
KIT, guide wire .045 10 ft or
KIT, guide wire .045 15 ft (consisting of)
TUBE, contact .030 wire
TUBE, contact .035 wire
TUBE, contact .045 wire
ADAPTER, tube con tact
.035 wire
LINER, monocoil .030
LINER, monocoil .045 wire
0-ring, 1/4 x 3/8
CONNECTOR, conduit
CONNECTOR, conduit
CONDUIT, .059 IDx 10 ft or
.CONDUIT,.O59IDxl5ft
CONDUIT, .080 ID x lOft or
.CONDUIT,.O8OIDxl5ft
.035 wire
GUIDE, outlet .030
GUIDE, outlet .045 wire
SCREW, machine steel flat hd 10-32 x 3/8
1
1
1
1
1
1
13
057148
HANDLE
1
1
1
1
1
1
14
030403
1
1
1
1
1
1
15
031 071
1
1
1
1
1
16
604860
16
604860
17
056766
18
056854
CABLE, power (consisting of)
STRIP, copper .010 x 3/4 x 2-1/2
CABLE, weld No. 1 10 ft (order by foot)
CABLE, weld No. 1 15 ft (order by foot)
LUG, 1-2 cable
TUBING, heat shrink 3/8 dia x 2-1/2 Ig
9
056077
9
056 078
10
056650
10
056651
10
056652
1
-
-
-
-
-
-
-
-
-
-
-
-
5
5
5
-
-
-
-
steel round hd 10-32
or
1/4
19
602088
SCREW, machine
20
056479
SPRING,
21
057 782
22
604 523
23
604 524
24
604 525
24
604 525
25
604 848
26
056049
26
056 509
27
010603
28
010606
29
604 550
29
604 550
30
056106
CORD, switch (consisting of)
CAP, midget twistlock 2P2W
COVER, seal-tite receptacle
CORD, portable No. 18 2/c lOft or
CORD, portable No. 18 2/c 15 ft (order by foot)
TERMINAL, disc knife 16-22
HOSE, gas lOft (consisting of)
HOSE, gas 15 ft (consisting of)
FITTING, hose brass barbed nipple 1/4 TBG
FITTING, hose brass nut 5/8-18 RH
HOSE, whippet 3/16 x 1 lOft or
HOSE, whippet 3/16 x 1 15 ft (order by foot)
CONNECTOR, torch end
-
x
strain relief
-
-
-
-
-
1
10 ft.
lOft.
lOft.
lOft.
10 ft.
10 ft.
15 ft.
15 ft.
lSft.
15 ft.
15 ft.
15 ft.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
9ft.
9ft.
9ft.
9ft.
9ft.
9ft.
l4ft.
l4ft.
l4ft.
l4ft.
14ft.
l4ft.
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
lift,
lift.
lift.
lift.
lift.
lift.
16 ft.
16 ft.
16 ft.
16 ft.
16 ft.
16 ft.
1
1
1
1
1
1
OM-1018 Page 2
Quantity
Model
-
Monocoil
Conduit
.8MM
.9MM
1.2MM
.8MM
.9MM
1.2MM
Item
FactOry
.0~31
.035
.047
.031
.035
.047
No.
Part No.
.030
.035
.045
.030
.035
.045
Figure A
31
056 830
32
056 839
33
604 848
34
603 521
35
604 525
36
603 886
37
604 874
38
604866
39
603 887
40
604 311
41
057 027
42
056 845
43
056 846
44
602 087
45
601 845
46
056847
47
604 937
48
058 346
49
058 347
50
604 771
51
031 016
52
058184
53
058 351
Description
Exploded View Of Gun Assembly tContd.)
SWITCH & HOUSING ASSEMBLY (consisting of)
.
SWITCH,
gun
(consisting of)
TERMINAL, disc. knife 16-22
order by foot)
TUBING, plastic vinyl (6 inches reqd
CORD, portable No. 18 2/c
NUT, steel hex 2-56
WASHER, lock steel split No. 2
SWITCH, licon
SCREW, machine steel round hd 2-56 x 1/2
.GROMMET, rubber 1/4 ID x 3/8 hole x 1/16 groove
RELIEF, strain
HOUSING, switch gun
LEVER, actuating switch
SCREW, machine steel round hd 8-36 x 1-1/4
NUT, steel self locking hex 8-32
.SPRING,switch
SCREW, self tapping pan hd 6-32 x 1/4
TUBE, head with components (consisting of)
TUBE, head (consisting of)
SCREW, set~ steel 10-32 x 1/8
SCREW, set -steel 10-32 x 3/8
.INSULATOR,body.torch
TUBING, neoprene 5/8 ID x 3/32 wall x 3.9/16
..
-
.
.
.
.
.
.
.
.
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1 ft.
1 ft.
1 ft.
1 ft.
1 ft.
1 ft.
3 ft.
3 ft.
3 ft.
3 ft.
3 ft.
3 ft.
2
2
2
2
2
2
2
2
2
2
2
.
2
.
1
1
1
1
1
.
1
.
2
2
2
2
2
.
2
.
.
..
.
-
.
..
-
.
.
-
.
.
-
-
.
-
.
-
.
.
-
.
BE SURE TO PROVIDE
Page 3
a
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
STOCK, MODEL, AND STYLE NUMBERS WHEN ORDERING REPLACEMENT PARTS.
Quantity
Model
Item
Factory
No.
Part No
Figure
B
Description
Kit, Guide
-
057083
(iUIL)E,
outlet
61
056741
GUIDE,
outlet
62
057218
62
057 220
62
057219
MONOCOIL ASSEMBLY, lOft or
MONOCOI L ASSEMBLY, 15 ft (consisting of)
MONOCOIL ASSEMBLY, lOft or
62
057 221
MONOCOI L ASSEMBLY, 15 ft (consisting of)
63
057 307
63
057 308
64
602173
65
057 309
66
602 959
CONNECTOR, monocoil (consisting of)
CONNECTOR, monocoil (consisting of)
SCREW, set steel socket hd 10-32 x 1/4
FITTING, brass barbed liner
FITTING, hose brass nut oxygen 9/16-18
-
605 545
70
056083
70
056084
71
602172
72
058174
.0-RING
73
054158
74
054 242
74
054183
74
054157
contact
ADAPTER,
TUBE, contact .030 wire
TUBE, contact .035 wire
TUBE, contact .045 wire
056759
68
056 760
68
056761
.045
(00)
NO
N N
N
NN
Nh
~
N
~
-
LC)LC~
LULO
LOLU
00
00
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
11 ft.
11 ft.
11 ft.
16 ft.
16 ft.
16 ft.
1
-
tube
~Q
Nb
00
RH
605 545
68
.035
1
69
056 758
.047
.
-
69
056112
68
.035
-
FITTING, hose brass ferrule .475 ID x 23/32
CONDUIT, .190/.191 OD 10 ft 10 inches or
CONDUIT, .059 ID x .189 OD 15 ft 10 inches
.CONDUIT, .084 ID x .212OD loft lOinchesor
CONDUIT, .084 ID x .212 OD 15 ft 10 inches
.TUBING, neoprene 17/64 ID lOft or
TUBING, neoprene 17/64 ID 15 ft (order by foot)
CONNECTOR, gun (consisting of)
CONNECTOR, gun (consisting of)
SCREW, set steel socket hd 10-32 x 3/16
67
.9MM
.031
Wire Monocoil 10 & 15 Ft.
61
1.2MM
.8MM
-
1
1
1
1
1
1
1
5
5
5
62
TB.075 176
Figure B
Kit, Wire Guide
-
Monocoil
BE SURE TO PROVIDE STOCK, MODEL, AND STYLE NUMBERS WHEN ORDERING REPLACEMENT PARTS.
OM-1018 Page 4
$