Central Machinery 8 in. Bench Grinder with Gooseneck Lamp Owner's Manual & Safety Instructions


Add to my manuals
16 Pages

advertisement

Central Machinery 8 in. Bench Grinder with Gooseneck Lamp Owner's Manual & Safety Instructions | Manualzz
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
REV 15a
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2014 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Table of Contents
Safety
Safetye��������������������������������������������������������� 2
Specifications.............................................. 7
Setup........................................................... 8
Operationa��������������������������������������������������� 10
Maintenancei���������������������������������������������� 12
Parts List and Diagram............................... 14
Warranty..................................................... 16
WARNING SYMBOLS AND DEFINITIONS
Setup
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Operation
IMPORTANT SAFETY INFORMATION
General Tool Safety Warnings
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Maintenance
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning it on.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations,
or expose them to rain. Keep work area well lighted.
Page 2
5. KEEP CHILDREN AWAY. All visitors should
be kept safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks,
master switches, or by removing starter keys.
7. DON’T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don’t force tool or attachment
to do a job for which it was not designed.
For technical questions, please call 1-888-866-5797.
Item 62501
0–6
18
16
16
14
6.1 – 10
18
16
14
12
10.1 – 12
16
16
14
12
12.1 – 16
14
12
Do not use.
9. USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating.
Table A shows the correct size to use depending
on cord length and nameplate ampere rating.
If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
10. WEAR PROPER APPAREL. Do not wear
loose clothing, neckties, rings, bracelets, or
other jewelry which may get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
15. DISCONNECT TOOLS before servicing;
when changing accessories, such as
blades, bits, cutters, and the like.
16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in
off position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.
18. NEVER STAND ON TOOL.
Serious injury could occur if the tool is tipped or
if the cutting tool is unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function – check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
20. DIRECTION OF FEED.
Feed work into a blade or cutter against the
direction of rotation of the blade or cutter only.
21. NEVER LEAVE TOOL RUNNING
UNATTENDED. TURN POWER OFF.
Maintenance
12. SECURE WORK. Use clamps or a vise to
hold work when practical. It’s safer than using your
hand and it frees both hands to operate tool.
14. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for
lubricating and changing accessories.
Safety
(at full load)
EXTENSION CORD
LENGTH
25′
50′ 100′ 150′
Setup
NAMEPLATE
AMPERES
13. DON’T OVERREACH.
Keep proper footing and balance at all times.
Operation
Table A: RECOMMENDED MINIMUM WIRE GAUGE
FOR EXTENSION CORDS
(120 VOLT)
Item 62501
For technical questions, please call 1-888-866-5797.
Page 3
Grounding Instructions
Safety
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT
GROUNDING WIRE CONNECTION READ AND FOLLOW THESE INSTRUCTIONS:
110-120 VAC Grounded Tools: Tools with Three Prong Plugs
1. In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Setup
2. Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.
3. Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow
stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or
plug is necessary, do not connect the equipmentgrounding conductor to a live terminal.
Operation
4. Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as
to whether the tool is properly grounded.
5. Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.
6. Repair or replace damaged or
worn cord immediately.
Grounding
Pin
125 VAC 3-Prong Plug and Outlet
(for up to 125 VAC and up to 15 A)
7. This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated above in
125 VAC 3-Prong Plug and Outlet. The tool has
a grounding plug that looks like the plug illustrated
above in 125 VAC 3-Prong Plug and Outlet.
8. The outlet must be properly installed and grounded
in accordance with all codes and ordinances.
9. Do not use an adapter to connect
this tool to a different outlet.
Maintenance
Page 4
For technical questions, please call 1-888-866-5797.
Item 62501
Grinder Safety Warnings
4. Always use guards and eye shields.
5. Do not overtighten wheel nut.
6. Use only flanges furnished with the grinder.
7. Adjust distance between wheel and work rest
to maintain 0.125 inch or less separation as the
diameter of the wheel decreases with use.
8. Frequently clean grinding dust from beneath grinder.
9. Wear a full face shield over ANSI‑approved
safety goggles during use.
10. Do not grind with side of wheel unless wheel is
specifically designed for that type of grinding.
11. DO NOT OPERATE WITH ANY GUARD
DISABLED, DAMAGED, OR REMOVED. Moving
guards must move freely and close instantly.
12. The use of accessories or attachments not
recommended by the manufacturer may
result in a risk of injury to persons.
13. When servicing use only identical replacement parts.
14. Do not depress the spindle lock when
starting or during operation.
15. Only use safety equipment that has been approved
by an appropriate standards agency. Unapproved
safety equipment may not provide adequate
protection. Eye protection must be ANSI-approved
and breathing protection must be NIOSH-approved
for the specific hazards in the work area.
16. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
Item 62501
19. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
Safety
3. Replace cracked wheel immediately.
20. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
21. WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities, contains chemicals known to the State
of California to cause cancer and birth defects or
other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other
masonry products
• Arsenic and chromium from chemically
treated lumber
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
22. WARNING: The cord of this product contains
lead and/or di (2-ethylhexyl) phthalate (DEHP),
chemicals known to the State of California
to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
23. The warnings, precautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.
For technical questions, please call 1-888-866-5797.
Setup
2. Use grinding wheel suitable for speed of grinder.
18. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
Operation
1. Wear eye protection.
17. Industrial applications must follow OSHA guidelines.
Maintenance
For Your Own Safety Read Instruction
Manual Before Operating Grinder
Page 5
Vibration Safety
Safety
This tool vibrates during use. Repeated or
long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check‑ups
to ensure medical problems are not being caused
or worsened from use. Pregnant women or
people who have impaired blood circulation to
the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Use tools with the lowest vibration when there
is a choice between different processes.
4. Include vibration-free periods each day of work.
5. Grip workpiece as lightly as possible (while still
keeping safe control of it). Let the tool do the work.
6. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
Setup
SAVE THESE INSTRUCTIONS.
Operation
Maintenance
Page 6
For technical questions, please call 1-888-866-5797.
Item 62501
Electrical Rating
110-120VAC / 60Hz / 3.6A
Motor No Load Speed
3560 RPM
Max. Accessory Diameter
8" OD x 3/4″ x 5/8″ Arbor
Arbor Size
5/8″
Mounting Holes
(2) 7/16"
Work Light Bulb
120V/60W (Sold separately)
Safety
Specifications
Maintenance
Operation
Setup
E237800
Item 62501
For technical questions, please call 1-888-866-5797.
Page 7
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Safety
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.
Note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Assembly/Mounting
Shield
Arm (67)
The two mounting holes in the Base can be used
to attach this Grinder to a stable workbench
using appropriate hardware (sold separately).
Setup
1. Install Right Work Rest (60) to the
Right Wheel Guard (43). Use Bolt (57),
Spring Washer (47), and Flat Washer (58)
to secure it in place, as shown in Figure A.
Spark
Guard
(62)
Knob (12)
Figure B: Spark Guard and
Right Shield Arm Installation
6. Attach the Right Eye Shield Arm (67) to the
Right Wheel Guard (43) using an Eye Shield
Mounting Knob (12) and Washer (11), see Figure B.
Right
Work
Rest (60)
7. Attach the Left Eye Shield Arm (10) to the
Left Wheel Guard (9) using an Eye Shield
Mounting Knob (12) and Washer (11).
Bolt (57)
Operation
Flat Washer
(58)
Spring
Washer (47)
8. Attach the Eye Shields (21) to the Eye
Shield Arms (10, 67) using Screws (13),
Spring Washers (14), Flat Washers (15),
and Nuts (16) as shown in Figure C.
Figure A: Work Rest Installation
2. Install Left Work Rest (59) to the
Left Wheel Guard (9) using Bolt (57), Spring
Washer (47), and Flat Washer (58).
Spring Washer (14)
Nut (16)
Screw (13)
Flat Washer (15)
Knob (12)
3. Adjust the Work Rests to within 1/16″ of the
Grinding Wheel. To adjust this distance,
loosen Bolts (57) and move Work Rests (59/60).
Maintenance
4. Attach a Spark Guard (62, 63) to
each Wheel Guard (9,43) using a
Bolt (66), Spring Washer (65) and Flat
Washer (64) as shown in Figure B.
5. Adjust each Spark Guard (62, 63) to within
1/16" (0.0625") of the Grinding Wheel
and tighten each Bolt (66).
Page 8
Shield
Arm (67)
Eye Shield
(21)
Figure C: Right Eye Shield Installation
For technical questions, please call 1-888-866-5797.
Item 62501
Safety
Functions
Lamp
Eye Shields
Setup
Wheel Guards
Operation
Spark
Guards
Grinding Wheels
Work Rests
Item 62501
For technical questions, please call 1-888-866-5797.
Maintenance
On/Off Switch
Page 9
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Safety
Tool Set Up
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.
TO PREVENT SERIOUS INJURY:
DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED.
Moving guards must move freely and close instantly.
Installing a Grinding Wheel
Setup
1. The Grinding Wheel MUST be:
• rated to at least 3,560 RPM.
• no larger than 8″ (203 mm) in diameter.
• fitted with a 5/8″ round arbor hole.
• 3/4″ thick or less.
• suitable for edge grinding, not surface grinding.
• dry and clean.
• proven undamaged by inspection and
by the ring-test explained below.
2. Remove the Outer Flange.
Keep the Inner Flange in position on the Spindle.
Operation
3. Closely inspect the wheel before mounting.
Perform a ring-test on the wheel (unless wheel is
smaller than 4″ or is an unusual shape) as follows:
a. Suspend wheel using a dowel or
finger through the arbor hole.
Hang
Wheel
from
Dowel
45°
V
E
R
T
I
C
A
L
Tap
Wheel
Here
c. Rotate the wheel 90° and repeat the test
until the entire wheel has been checked.
d. An undamaged wheel will
give a clear tone. If cracked, there will be
a dead sound and not a clear ring.
4. For wheels with paper gaskets (blotters) or
metal gaskets: Slip the grinding wheel onto the
Spindle with the gasket first. The gasket should be
centered on the grinding wheel and the wheel and
gasket should rest flat against the Inner Flange.
WARNING: To prevent serious injury, gaskets
must be used for all grinding wheels they are
provided with. Gaskets help prevent grinding
wheel damage and wheel slippage,
causes of wheel failure.
5. Thread the Outer Flange onto the Spindle.
Wrench tighten only enough so that the wheel is
securely held on the spindle.
WARNING: To prevent serious injury,
do not overtighten flange. Overtightening can
damage the wheel, causing wheel failure.
Maintenance
C
E
N
T
E
R
45°
Page 10
45°
b. Tap the flat side of the wheel with a light
non‑metallic object, such as a screwdriver
handle, at a point 45° from the vertical center
line on each side of the wheel and 1 – 2 inches
from the edge of the wheel (see Illustration).
45°
For technical questions, please call 1-888-866-5797.
Item 62501
1. Designate a work area that is clean and well‑lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.
3. There must not be objects, such as utility lines,
nearby that will present a hazard while working.
General Operating Instructions
1. Make sure that the Switch is in the off‑position,
then plug in the tool.
5. To create a smoother surface,
keep the workpiece moving over the wheel.
2. Turn on the tool.
6. To prevent accidents, turn off the tool and unplug
the tool from its electrical outlet after use. Clean,
then store the tool indoors out of children’s reach.
3. Allow the tool to come up to full speed
before touching the wheel.
Maintenance
Operation
Setup
4. Apply the workpiece to the wheel,
allowing the tool to operate at full speed.
If the tool bogs down, use lighter pressure.
Safety
Workpiece and Work Area Set Up
Item 62501
For technical questions, please call 1-888-866-5797.
Page 11
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
Safety
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:
Setup
• loose hardware,
• misalignment or binding of moving parts,
• cracked or broken parts,
• damaged electrical wiring, and
• any other condition that may
affect its safe operation.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.
3. Periodically, wear ANSI‑approved
safety goggles and NIOSH‑approved
breathing protection and blow dust and grit out
of the motor vents using dry compressed air.
4.
WARNING! If the supply cord of this
power tool is damaged, it must be replaced
only by a qualified service technician.
Accessory Storage and Handling
Operation
1. Handle accessories carefully to prevent
dropping or bumping. Do not use wheels
that have been dropped or bumped.
2. Store accessories in shelves, racks, boxes, or
drawers. Keep storage area dry and above
freezing. Any grinding or cut-off wheels exposed to
humidity or freezing temperatures must not be used.
Maintenance
Page 12
For technical questions, please call 1-888-866-5797.
Item 62501
Troubleshooting
Tool will not start. 1. Cord not connected.
2. No power at outlet.
Tool operates
slowly.
Performance
decreases
over time.
3. Tool’s thermal reset breaker
tripped (if equipped).
4. Internal damage or wear. (Carbon
brushes or switch, for example.)
Extension cord too long or
wire size too small.
1. Accessory dull or damaged.
2. Carbon brushes worn or damaged.
Excessive noise 1. Internal damage or wear. (Carbon
or rattling.
brushes or bearings, for example.)
Overheating.
1. Forcing machine to work too fast.
2. Accessory dull or damaged.
3. Blocked motor housing vents.
4. Motor being strained by long or
small diameter extension cord.
Likely Solutions
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Have technician service tool.
Safety
Possible Causes
Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for its
length and load. See Table A on page 3.
1. Keep cutting accessories sharp.
Replace as needed.
2. Have qualified technician replace brushes.
1. Have technician service tool.
1. Allow machine to work at its own rate.
2. Keep cutting accessories sharp.
Replace as needed.
3. Wear ANSI-approved safety goggles and
NIOSH‑approved dust mask/respirator while
blowing dust out of motor using compressed air.
4. Eliminate use of extension cord.
If an extension cord is needed, use one with
the proper diameter for its length and load.
See Table A on page 3.
Maintenance
Operation
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
Setup
Problem
Item 62501
For technical questions, please call 1-888-866-5797.
Page 13
Parts List and Diagram
PLEASE READ THE FOLLOWING CAREFULLY
Safety
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List
Part
Setup
Operation
Maintenance
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Description
Screw
Flat Washer
Nut
Left Wheel Cover
Wheel Nut
Flange
Paper Washer
Wheel
Left Wheel Guard
Left Eye Shield Arm
Eye Shield Locking Washer
Eye Shield Locking Knob
Screw
Spring Washer
Flat Washer
Nut
Screw
Flat Washer
Nut
Eye Shield Bracket
Eye Shield
Gooseneck Lamp
Flat Washer
Nut
Base
Strain Relief
Plate
Screw
Screw
Tooth Washer
Power Cord
Nut
Flat Washer
Spring Washer
Qty
6
6
6
1
2
4
4
2
1
1
2
2
2
2
2
2
4
4
4
2
2
1
1
1
1
1
1
2
1
1
1
4
4
4
Part
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
Description
Screw
Screw
Motor End Bell
Motor Case
Motor (Stator)
Ball Bearing
Rotor
Spring Washer
Right Wheel Guard
Right Wheel Cover
Mounting Plate
Switch
Spring Washer
Screw
Base Plate
Rubber Foot
Flat Washer
Screw
Capacitor
Capacitor Holder
Flat Washer
Screw
Bolt
Flat Washer
Left Work Rest
Right Work Rest
Screw
Right Spark Guard
Left Spark Guard
Flat Washer
Spring Washer
Bolt
Right Eye Shield Arm
Qty
4
6
2
1
1
2
1
1
1
1
1
1
4
2
1
4
4
4
1
1
1
1
4
4
1
1
2
1
1
2
2
2
1
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Page 14
For technical questions, please call 1-888-866-5797.
Item 62501
Safety
3
32
33
34
35
36
66
37
65
64
63
64
25
Setup
2
5
7
6
57
62
65
38
66
21
13
14
15
17
18
20
19
57
10
11
12
47
13
14
15
16
17
18
61
19
20
24
48
58
67
16
21
11
40
60
12
39
22
23
42
41
43
Operation
1
4
6
8
7
9
59
58 47
45
46
49
50
51
52
6
40
7
8
37
31
30
29
28
27
26
25
53
54
55
56
7
6
36
5
44
3
2
1
Page 15
For technical questions, please call 1-888-866-5797.
Item 62501
Maintenance
Assembly Diagram
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement