Sencor SSI 7710BL User's Manual

SENCOR SSI7710BL
EN = Steam Iron
Copyright © 2017, Fast CR, a.s. -1- Revision 07/2017
EN Steam Iron
Important safety instructions
READ CAREFULLY AND STORE FOR FUTURE USE.
= This iron may be used by children 8 years of age and older and by persons with
physical or mental impairments or by inexperienced persons, if they are properly
supervised or have been informed about how to use the iron in a safe manner
and understand the potential dangers. Do not allow children to play with the iron.
Cleaning and maintenance performed by the user must not be performed by
unsupervised children. If it is connected to a power socket or if it is cooling down,
keep the iron and its power cord out of reach of children younger than 8 years of
age.
= This iron is designed for home use. Do not use it in industrial surroundings or
outdoors.
= Before connecting the iron to a power socket, check that the nominal voltage
stated on the rating label matches the electrical voltage in the socket.
= Connect the iron only to a properly grounded socket.
= The iron must not be left without supervision when connected to a power socket.
« Do not place the iron on or near an electric or gas stove or other sources of heat.
= The iron may be used only on a stable, even surface. This also applies for putting
down the iron. When putting the iron down on to the stand, check that the surface
on which the stand is located is stable.
= Do not touch the iron with wet or damp hands when it is connected to a power
socket.
= Never iron clothing directly on the body.
= Do not touch the hot soleplate. Otherwise, this could cause burns.
= Always disconnect the iron from the power socket when leaving it without
supervision, when filling up or emptying the water tank and when you have
finished using it. Before disconnecting the iron from a power socket, turn off the
steam function and set the temperature control dial to the MIN. position.
= Never fill the water tank directly underneath a water tap. Always use the supplied
container for filling the water tank. Never add vinegar, descaling agents or other
additives to the water tank.
= Prior to cleaning or any other handling of the iron that you have disconnected
from the power socket, allow the soleplate to cool down.
= To avoid potential injury by electrical shock, do not clean the iron under running
water, do not spray it with water and do not submerge it in water or any other
liquid.
Copyright © 2017, Fast CR, as. -2- Revision 07/2017
= The iron must not be used if it has fallen on the floor, exhibits visible signs of
damage or if it is leaking.
= Ensure that the power cord does not come into contact with water or a heated
surface.
= Disconnect the iron from the power socket by gently pulling the plug of the power
cord, and not the power cord itself. Otherwise, this could damage the power cord
or the socket.
=» If the power cord is damaged, have it replaced at a professional service centre or by
a similarly qualified person, this will prevent the creation of a dangerous situation.
It is forbidden to use the iron if it has a damaged power cord.
« To avoid the danger of injury by electrical shock, do not repair the iron yourself or
make any adjustments to it. Have all repairs performed at an authorised service
centre. By tampering with the product you risk voiding your legal rights arising
from unsatisfactory performance or quality warranty.
Copyright © 2017, Fast CR, as. -3- Revision 07/2017
SW N =
nn
Steam Iron
User's manual
m Prior to using this appliance, please read the user's manual thoroughly,
even in cases, when one has already familiarised themselves with previous
use of similar types of appliances. Only use the appliance in the manner
described in this user's manual. Keep this user's manual in a safe place
Where it can be easily retrieved for future use.
= We recommend saving the original cardboard box, packaging material,
purchase receipt and responsibility statement of the vendor or warranty
card for at least the duration of the legal liability for unsatisfactory
performance or quality. In the event of transportation, we recommend that
you pack the appliance in the original box from the manufacturer.
DESCRIPTION OF THE IRON
A1 Anti-slip handle A9 Temperature control dial
A2 Indicator light enables correct temperature
signals maintenance of set setting for ironing laundry.
temperature or automatic A10 Self-Clean button
shut-off. for removing limescale deposits
A3 Steam impulse button A11 Transparent easy-to-fill water
A4 Water spraying button tank (capacity 300 ml)
A5 Variable steam emission control A12 Ceramic soleplate
A6 Water tank filling opening cap A13 Water tank filling container
A7 Water spraying nozzle (not shown)
A8 Swivel power cord end
limits twisting and tangling of
the power cord.
PREPARATION BEFORE IRONING
Sort the laundry according to international symbols shown on the textiles
or according to the fabric types.
SETTING
SYMBOL THE TEMPERATURE DIAL
FABRICTYPE
Synthetics (nylon,
polyester, acrylic,
viscose, etc.)
e
low temperature
Silk — wool ;
medium temperature
Cotton — linen high temperature
Fabric, that should not be ironed
XDD
USING THE IRON
A
Before first use, remove all packaging materials including promotion
stickers and labels from the iron. Wipe the soleplate A12 with a lightly
dampened cloth before first use and then wipe dry.
FILLING THE WATER TANK
Before filling the water tank A11, check that the iron is disconnected from
the power socket and that the temperature control dial A9 is set to the MIN.
position.
Set the steam emission control AS to the top position. This will deactivate
the steam emission function.
Fill the included container A13 with water. Use tap water (soft to medium
water hardness). If water in your area is hard or very hard (more than 14 °dH
/ 2.5 mmol/l), we recommend that you mix tap water with distilled water at
a ratio of 1:1.
Attention:
Never add water softeners, perfumes or other additives to the water.
N
A
5.
A
Place the iron into the upright position. Flip open the filling opening
cap A6. Use one hand to hold the handle A1 and tilt the iron so that the
soleplate A12 is at an angle of approximately 45° relative to the surface on
which the iron is located. Then carefully pour the water from the container
A13 through the filling opening into the water tank A11. When the iron
is in the upright position, the water level must not exceed the maximum
mark on the water tank A11.
After filling the water tank A11, close the filling opening cap A6 and put
the iron in the upright position.
ANTI-CALC SYSTEM
This iron is equipped with a permanent Anti-Calc filter, which limits the
formation of limescale deposits inside the iron. This filter cannot be
deactivated. The effectiveness of the filter depends on the hardness of the
water used.
SETTING THE TEMPERATURE
Place the iron in the upright position on an even and stable surface and
connect the power cord to a power socket.
Set the temperature on the temperature control dial A9 according to the
type of fabric that you wish to iron, see chapter Preparation before ironing.
The indicator light A2 will turn on. This signals that the soleplate A12 is
heating up. As soon as the soleplate A12 heats up to the set temperature,
the indicator light A2 will turn off. Now you may commence ironing your
laundry.
During first use, a weak cracking sound caused by the expanding plastic
may be heard. This is an entirely normal event, which will disappear in
a short time.
While ironing, the indicator light A2 will intermittently turn on and off. This
indicates that the set temperature is being maintained.
First iron the laundry that requires the lowest temperature. This will save
you time because the soleplate A12 heats up faster than it cools down.
If you iron some fabrics at a higher temperature and then set a lower
temperature, it is necessary to wait until the soleplate A12 cools down.
To prevent damaging its surface, do not move the soleplate A12 over sharp
or hard items such as buttons or zips.
STEAM FUNCTION
The continuous steam function can be use when the water tank A11 is
filled with water. If you wish to iron with steam, temperature must be set
in the range from eee to MAX. Turning the steam emission control A5
downwards, variably increases the steam emission and vice versa. Setting
the steam emission control A5 to the top position, deactivates the steam
function.
In the event that the steam function is set at the same time as the
temperature control dial A9 is set to low e or medium ee temperature,
water could drip out of the soleplate A12. For this reason, the iron is
equipped with the Drip-Stop system, which automatically stops the steam
process when the temperature control dial A9 is not set to a high enough
temperature, and thereby prevents potential dripping from the steam
outlets.
Note:
The iron continuously emits steam only if you hold it in a horizontal
position. You can stop the release of steam by standing the iron
upright.
Attention:
Do not use the steam function for silk and synthetics so as not to
damage the fabric.
STEAM IMPULSE FUNCTION
Press the steam impulse button A3 to generate a strong flow of steam,
which can straighten out even very crumpled up textiles.
Only use the steam impulse function when the temperature control dial A9
is set to a temperature in the range from eee to MAX. In order to use this
function, the water tank A11 must be filled with water. If indicator light A2
turns on, wait until it turns off and only then press the button A3. Wait at
least 5 seconds before pressing the button A3 again.
The steam impulse function can also be used when ironing hanging
textiles (e.g. curtains, garments hanging on coat hangers, etc.).
Attention:
Do not use the steam impulse function on silk and synthetics in order
not to damage the fabric.
Copyright © 2017, Fast CR, as.
Revision 07/2017
6. WATER SPRAYING FUNCTION
® The water spraying function can be used at any ironing temperature. Make
sure that there is water in the water tank A11. To spray textiles with water
using the nozzle A7, press button A4. When using the water spraying
function for the first time or when you have not used the iron for a long
time, it will be necessary to press button A4 several times before the nozzle
A7 starts working correctly.
Note:
Do not use the spraying function on silk and synthetics.
7. AUTOMATIC SHUT-OFF FUNCTION
® The iron will shut off automatically when left 8 minutes without movement
in the upright position, or after 30 seconds without movement in the
horizontal position. The automatic shut-off function is indicated by
a warning sound and a flashing indicator light A2. If you move the iron,
the automatic shut-off function will be deactivated and the iron will be put
back into operation.
A
Note:
Despite the iron being equipped with an automatic shut-off
function, for safety reasons, never leave it without supervision when
it is connected to a mains power socket.
8. TURNING OFF
= When you have finished using the iron, stand it upright and set the steam
emission control A5 to the top position. This will deactivate the steam
function. Set the temperature control dial A9 to the MIN position and
disconnect the power cord from the power socket and allow the soleplate
A12 to cool down. After the soleplate A12 has cooled down, clean the iron
according to the instructions in chapter Cleaning and maintenance.
TIPS FOR QUALITY IRONING
® Do not fill the washing machine drum with too much laundry, otherwise it
will be overly crumpled up. You can also avoid overly crumpled laundry by
setting a lower spin drying speed.
m [f you are ironing fabrics from blended materials (e.g. 40 % wool and 60 %
synthetic material), set the temperature control dial A9 according to the
material that is ironed at a lower temperature.
m If you do not know the composition of the fabric, identify the suitable
temperature dial setting by ironing a piece of the fabric from the underside.
Start by setting the temperature control dial A9 to a low temperature and
gradually increase it until the ideal temperature is achieved.
mM Never iron over places that have sweat marks or other stains. The high
temperature fixes the stain, making it difficult to remove.
® To avoid silk, wool and synthetic fabrics from being shiny after ironing, iron
them from the underside.
® Some materials are easier to iron when they are lightly damp.
mM Spray fine fabrics before ironing them or iron them under a lightly
dampened wiping cloth.
CLEANING AND MAINTENANCE
CLEAN AFTER EVERY USE
m Before cleaning the iron, turn it off according to the instructions in chapter
Using the iron. The power cord must be disconnected from the power
socket and the soleplate A12 must be cool. Open the filling opening cap
A6 and then empty out the water tank A11 over a sink. Close the cap A6
again.
mM In the event that the soleplate A12 or the surface of the iron is dirty, wipe
With a lightly dampened cloth and then wipe dry.
® For cleaning, do not use steel wool, solvents or cleaning products with an
abrasive effect, etc. to prevent damaging the surface being cleaned. Do not
submerge the iron in water when cleaning it.
REMOVING LIMESCALE DEPOSITS
For the removal of limescale deposits from the inner part of the soleplate
A12, the iron is equipped with a Self-Clean function. Use this function
regularly at least once every 14 days.
mM Make sure that the steam emission control A5 is set to the top position
(deactivated) and that the iron is disconnected from the power socket.
Fill the water tank A11 with clean water up to the maximum water mark.
Connect the iron to a power socket. Set the temperature control dial A9 to
maximum and wait until the control light A2 turns off. Disconnect the iron
from the power socket and hold it in a horizontal position above the sink.
Press the Self-Clean button A10 and hold it down. Steam and hot water will
start to be emitted from the soleplate A12. At the same time also limescale
deposits from the inner parts of the soleplate A12 will be removed. Tilt the
iron from side to side several times until the water tank A11 is completely
empty. After emptying it out, release the button A10. You may repeat the
entire process once more if necessary.
—
.
N
® Connect the iron to a power socket and allow it to heat up once more
to the maximum temperature in order to dry out the soleplate A12. Iron
over a piece of unneeded fabric to remove water stains that formed on
the soleplate A12 during the cleaning process. Then set the temperature
control dial A9 to the MIN position, disconnect the iron from the power
socket and allow it to cool down.
TECHNICAL SPECIFICATIONS
Rated voltage range 220-240V
Rated frequency 50/60 Hz
Rated power input 2 000-2 400 W
Changes to text and technical parameters are reserved.
INSTRUCTIONS AND INFORMATION REGARDING THE
DISPOSAL OF USED PACKAGING MATERIALS
Dispose of used packaging material at a site designated for waste in your
municipality.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC
EQUIPMENT
This symbol on products or original documents means that
used electric or electronic products must not be added to
ordinary municipal waste. For proper disposal, renewal and
recycling hand over these appliances to determined collection
points. Alternatively, in some European Union states or other
European countries you may return your appliances to the local
| retailer when buying an equivalent new appliance.
Correct disposal of this product helps save valuable natural
resources and prevents potential negative effects on the environment and
human health, which could result from improper waste disposal. Ask your local
authorities or collection facility for more details.
In accordance with national regulations penalties may be imposed for the
incorrect disposal of this type of waste.
For business entities in European Union states
If you want to dispose of electric or electronic appliances, ask your retailer or
supplier for the necessary information.
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of this
product, request the necessary information about the correct disposal method
from the local council or from your retailer.
This product meets all the basic requirements of EU directives
related to it.
Copyright © 2017, Fast CR, a.s.
Revision 07/2017