- Industrial & lab equipment
- Electrical equipment & supplies
- Power conditioning
- Electrical relays
- Vega
- VEGACAP 64
- Specification
Vega VEGACAP 64 Capacitive rod probe for level detection of adhesive products Specification
Add to My manuals2 Pages
Vega VEGACAP 64 is a reliable point level sensor designed to detect the level of non-abrasive liquids and bulk solids. With its fully insulated rod electrode, it's perfect for viscous and adhesive products. Installation and mounting are simple and straightforward, with no special requirements.
advertisement
![Vega VEGACAP 64 Capacitive rod probe for level detection of adhesive products Specification | Manualzz Vega VEGACAP 64 Capacitive rod probe for level detection of adhesive products Specification | Manualzz](http://s3.manualzz.com/store/data/051984141_1-9c75e1f2c28202917c2cc91befd3b003-360x466.png)
Specification sheet
VEGACAP 64
Relay (DPDT)
Capacitive rod electrode for level detection
Application area
The VEGACAP 64 point level sensor for non-abrasive liquids and bulk solids. The rod electrode is fully insulated and due to its construction it is suitable for viscous and adhesive products.
Your benefit
• Reduced number of cleaning cycles through measurement insensitive to buildup
• Reliable measurement with strong buildup through optimized design
• Long lifetime and low maintenance requirement through robust construction
Function
Sensor and vessel form the two electrodes of a capacitor. A capacitance change caused by a level change is evaluated by the integrated electronics and converted into a switching signal. The capacitive measuring principle has no special requirements in respect to installation and mounting.
Technical data
Sensor length
Process fitting
Process pressure
Process temperature
Ambient, storage and transport temperature
Operating voltage
Power consumption
Switching voltage
Switching current
Breaking capacity
Switching delay up to 4 m (13.12 ft)
Thread from G¾, ¾ NPT, flanges from
DN 50, 2"
-1 … +64 bar/-100 … +6400 kPa
(-14.5 … +928 psig)
-50 … +200 °C (-58 … +392 °F)
-40 … +80 °C (-40 … +176 °F)
20 … 253 V AC, 50/60 Hz; 20 … 72 V DC
1 … 8 VA (AC), approximately 1.5 W (DC) min. 10 mV, max. 253 V AC, 253 V DC min. 10 µA, max. 3 A AC, 1 A DC min. 50 mW, max. 750 VA AC, 54 W DC
0.7 s (on/off)
Materials
The wetted parts of the instrument are fully PTFE insulated.
You will find a complete overview of the available materials and seals in the "configurator" on our homepage at www.vega.com/configurator.
Housing versions
The housings are available in plastic, stainless steel or Aluminium.
They are available with protection ratings up to IP 67.
Electronics versions
The instruments are available in different electronics versions. Apart from the versions with transistor output, contactless electronic switch and relay output, a two-wire version for connection to a signal conditioning instrument is available.
Approvals
The instruments are suitable for use in hazardous areas and are approved e.g. according to ATEX and IEC. The instruments also have various ship approvals such as e.g. GL, LRS or ABS.
You can find detailed information at www.vega.com/downloads and
" Approvals ".
VEGA Americas, Inc, 4170 Rosslyn Drive, Cincinnati, Ohio USA 45209, www.vega-americas.com
VEGACAP 64 - 34683-US-160114
Specification sheet
Operation
The mode and switching point of the level switch can be adjusted on the electronics module. A signal lamp shows the switching status of the instrument.
6
1
2
3
5
Dimensions
SW 36 mm
(1.42")
G ¾
ø 16 mm
(0.63")
22 mm (0.87"
56 mm (2.21" 56 mm (2.21"
ø 40 mm
(1.58")
3
4
Oscillator with relay output
1 Potentiometer for switching point adaptation
2 DIL switch for measuring range selection (with compensation button)
3 DIL switch for mode adjustment
4 Ground terminal
5 Connection terminals
6 Control lamp
Electrical connection
3
2 1
Wiring plan
1 Relay output
2 Relay output
3 Voltage supply
You can find details on electrical connection in the instrument operating instructions on our homepage at www.vega.com/downloads.
1 2
1 Threaded version
2 Flange version
3 Threaded version with temperature adapter
LA Active length (50 … 200 mm)
Information
You can find further information on the VEGA product line on our homepage www.vega.com.
In the download section under www.vega.com/downloads you'll find free operating instructions, product information, brochures, approval documents, instrument drawings and much, much more.
Instrument selection
With the " Finder " at www.vega.com/finder and " VEGA Tools " you can select the most suitable measuring principle for your application.
You can find detailed information on the instrument versions in the
" Configurator " at www.vega.com/configurator and " VEGA Tools ".
Contact
You can find the VEGA agency serving your area on our homepage www.vega.com.
VEGACAP 64 - 34683-US-160114 VEGA Americas, Inc, 4170 Rosslyn Drive, Cincinnati, Ohio USA 45209, www.vega-americas.com
advertisement