advertisement
VTC-C2BHSE
2.1MP EX-SDI/HD-SDI Smart WDR Camera
FEATURES:
• 1/3” Panasonic Progressive Scan CMOS Sensor • 2.1MegaPixel With full 1080p/720p HD-SDI (SMPTE 292M) / EX-SDI Output • Smart Motion Zoom tracks motion, then intelligently zooms into that area of the frame • True Day/Night with Dual Filter Switch • Small scale design to fit in 5” dome enclosures such as the Pelco® DF5 Housing • Secondary Video (CVBS) Output • Fully programmable True WDR (Dual Scan) at 30fps • Sensitivity of 0.0005 Lux • Advanced OSD Functions: Smart Motion Zoom, Focus Assist, Motion Detection, Privacy Mask, Defog, D-Zoom(~8x), Sens-up (~x32), BLC/ HLC, Title Set, Pixel Defect Compensation, Lens Shade Compensation • 100% Pure Digital Transmission of video data • Extended Range Beyond 1000’ with RG59U 95% Copper Braid Coax • 12VDC / 24VAC Dual Voltage Operation
Safety Precaution To prevent electrical shock and risk of fire hazards, do not expose this unit to rain or moisture and only use specified power source..
CAUTION: TO REDUCE THE RISK OF ELECTICAL SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electrical shock.
The symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit.
Warning
: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.
Caution
: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Main power quality should be that of a typical commercial environment. If the user of the model requires continued operation during power interruptions, it is recommended that the device be powered from an uninterruptible power supply (UPS).
2 3
Safety Precaution
NOTICE
• The image used in this instruction manual are processed to help comprehension and may differ from actual video of the camera.
• Avoid installing in areas where shock or vibration may occur.
• Pay attention to safety when running the connection cables and make sure that the cables are not subject to heavy loads, kinks, moisture or damage.
• Never open the device (no user serviceable parts inside). The warranty becomes void if repairs are undertaken by unauthorized persons.
• Maintenance and repair have to be carried out only by authorized service centers.
• Use only a mild detergent to clean the housing.
• The camera should never be operated beyond the technical specifications. This can lead to damaging the device and void the warranty.
• The camera should never be operated in water.
3
Contents p.02~03
Safety Precaution
p.04
Contents
p.05
Features
p.06
Composition
p.06
Dimensions
p.07
Part Names
p.08~09
Installation Instructions
p.10~25
Operating Instructions
p.26
Specifications
4 5
4
Features
Key Features
• Full HD, 2Mega Pixel EX-SDI/HD-SDI CAMERA, 1920x1080(30p/25p) • Extended long reach HD Solution • Real time True WDR(Wide Dynamic Range) / 30fps • Improved noise figure with the enhanced 3DNR • CS mount supported (Option: C-mount adaptor) • Dual Filter Switcher • Day & Night Simulation for easy focus adjustment • Pointing Zoom which enables the flexible zooming of any area.
• Smart Motion Zoom in combination with Pointing Zoom.
• Motion Detection, Privacy Mask, Defog, Sens-up(~x32), WDR, H/V/HV Flip, D-Zoom(~8x), Lens Shade Compensation, BLC/HLC, Pixel Defect Compensation, Title Set • EX-SDI or HD-SDI switchable • Top performance at low light sensitivity (Sens-up On) • OSD menu & CVBS Video output BNC for easy installation & maintenance.
• Circuit protection against faulty connection in power polarity • Isolated power supply against ground loop problem • Back focus Flange • Power: 24VAC/12VDC
General Description
This camera incorporates a full (1920 x 1080p) HD camera module.
• With ICR mechanism, - Enhances its sensitivity about 10x at night time - Can accept infrared light • With Intelligent Focus Indicator and FOCUS ASSIST menu, - Offers easy adjustment of Focus • With 24VAC/12VDC dual power design, - Offers the flexibility of installation - Ensures the reliability
5
Composition Box Camera Operating Instruction Video Sub-out Cable (1pc) Dust Protection Cap (1pc) L- Wrench: 1.5mm (1pc) Dimensions
(unit : inches)
1.89
1.81
2.87
2.38
6 7
Part Names L-Wrench
Dust Protection Cap Mount Holes (Top / Bottom) Flange Lock screw ① ②
REAR VIEW
Back focus adjusting Flange Rear Case Front Case ③ ④ ①
Video out connector(BNC)
②
Power input terminal
③
OSD Control Joy stick (* Video format switched by OSD control joystick.)
④
DC Auto Iris Lens connector
PIN 4 PIN 3 PIN 2 PIN 1 Lens Connector for Auto Iris lenses
No.
1 2 3 4 DC Iris Damp(-) Damp(+) Drive(+) GND
7
Installation Instructions • Make sure the power is removed before installation.
• After all connections are properly finished, follow this order for applying power.
first connect the low voltage wires to the camera, then plug the AC/DC adapter to AC outlet to avoid damage..
1. Remove the dust protection cap from the lens mount.
2. Screw the lens onto the camera firmly (do not over tighten).
3. Plug the lens into the lens connector on the rear of camera case.
4. The camera has a 1/4” thread insert on top and bottom for mounting the camera to a wall or ceiling with a corresponding mount.
CAUTION
• Care should be taken that the cable is NOT damaged, kinked or exposed in a hazardous area.
• Do not point the camera lens directly at the sun or a spot light.
Setting the back focus adjustment
For easier and better adjustment, this camera provides FOCUS ASSIST menu which will assist you in the focusing of the camera.
When enabling FOCUS ASSIST menu, follow the procedure to get the best back focus adjustment.
1. Set the lens for the zoom position to WIDE and the focus position to INFINITE(∞).
2. Point the camera at an object about 30' away 3. Adjust ’Back focus adjusting Flange’ until the optimum focus is achieved.
4. Set the lens zoom position to TELE and adjust the lens focus for best focus.
5. Set the lens zoom position to WIDE again, check if the focus adjustment was the best. If not, re-adjust ‘Back focus Flange’ slightly.
6. After the setting, tighten the ‘Flange lock screw’ with L-wrench supplied.
Start up
When the camera is powered properly, it starts up with initializing the internal parameters.
8 9
8
Installation Instructions
Power Supply Connections
Camera can work with either 24AC or 12VDC, dual voltage power .
Primary and secondary grounds are completely isolated to avoid possible ground-loop problems
In case that HD-SDI/EX-SDI Inputs are not supported by the Monitor, please use HD-SDI/EX-SDI Converter to connect HD-SDI/EX-SDI cable with Monitor Please check Specification of the Monitor before installation.
Using OSD Controller
Setup menu can be accessed and controlled by OSD control joy stick on the rear of the camera unit. Five commands are available with the joy stick.
The design of rear panel could be different according to the camera models.
Description of the joystick operation
1) SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down for about 2 seconds 2) UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move the cursor up or down.
3) LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu. Used to adjust the desired menu selection and to move the cursor left or right.
4) denotes a long press down for about 2 seconds
Description of Video format switch (HD-SDI ↔ EX-SDI)
1) Default position is HD-SDI.
2) Switching the video format : ▲,▼, ▲,▼, ● ( long push 3~5 sec.) Do not remove power during video format change. This may cause damage to the camera
Description of D-ZOOM* adjustment
(*) Works only when OSD Menu is inactive.
1) ▲ : Zoom In 2) ▼ : Zoom Out
9
Operating Instructions
OSD menu Startup
Press ‘● ’ (OSD menu Joy stick key) down for about 2 seconds to access the setup menu mode.
MENU V5.xx
1. EXPOSURE 2. LENS 3. FOCUS ASSIST 4. SCENE ENHANCE 5. 3D-NR 6. DAY/NIGHT 7. PICT ADJUST 8. SPECIAL 9. SYSTEM A. EXIT DC NORMAL MID AUTO SAVE&EXIT
Direct Control menu
MAIN
EXPOSURE LENS FOCUS ASSIST
DEFAULT
DC -
DESCRIPTION
Sets EXPOSURE MODE, BRIGHTNESS, SENS-UP, AGC Sets Lens types.
Sets FOCUS SCENE ENHANCE 3D-NR DAY/NIGHT PICT ADJUST SPECIAL SYSTEM NORMAL SCENE ENHANCE provides several ways to enhance the video D-WDR, BLC and HLC.
MID EXT or AUTO Sets 3DNR level. LOW, MID, HIGH Sets DAY / NIGHT to EXT, AUTO, COLOR, B/W and COLOR D/N.
Set to EXT mode for cameras with IR-LED, AUTO mode for non IR-LED camera types. Sets WHITE BAL, SHARPNESS, COLOR GAIN, GAMMA Sets MIRROR/FLIP, PRIVACY, MOTION, PIXEL DEFECT, TITLE SET, DISPLAY, DEFOG, POINTING ZOOM Sets TV SYSTEM, RESOLUTION, COMM.SETUP, LANGUAGE and FACTORY DEFAULT
10 11
Operating Instructions EXIT SAVE & EXIT – Exits the menu after saving the parameters.
1. EXPOSURE
EXPOSURE
SHUTTER BRIGHTNESS SENS-UP AGC RETURN AUTO |:::::::|::::::| 10 OFF |:::::::|::::::| 12 RET
1-1. SHUTTER
(default: AUTO) : Set EXPOSURE MODE to AUTO, MANUAL and Flickerless. MANUAL and Flickerless modes disable SENS-UP functions. • AUTO: Optimizes the video level by controlling the iris and the shutter speed automatically.
• MANUAL: Iris and Shutter can be set to fixed.
• Flickerless : Reduces the flicker in video when US(60Hz)/EU(50Hz) mode is used in 50Hz/60Hz fluorescent lighting respectively.
1-2. BRIGHTNESS
(default: 10) : Adjusts the brightness of video (0~20).
2-3. SENS-UP
(default: AUTO) : A brighter video can be obtained by increasing the exposure time at night with SENS-UP. SENS-UP is the maximum integrations of frame by DSS (Digital Slow Shutter) in low light.
• AUTO: SENS-UP is enabled or disabled automatically by the scene brightness.
Higher SENS-UP can get brighter video but the slower frame rate will cause motion blur and more white pixels. If set to AUTO, maximum integration limit for SENS-UP can be set to x2, x4, X8, x16, X32 in SENS-UP menu.
• OFF: Disables SENS-UP.
2-4. AGC
(default: 12) : AGC(0~20) amplifies the video gain for brighter video but will cause noise and white pixel accordingly. AGC level less than 10 disables AUTO in DAY/NIGHT.
11
Operating Instructions
2. LENS
Select either DC or MANUAL lens.
Lens MUST be set to DC for the best image when DC iris lens is installed
2-1. DC
(default: INDOOR) : Select lens mode according to installation • INDOOR: Optimized for an indoor environment.
• OUTDOOR: Optimized for an outdoor environment.
• DEBLUR: ON enables MOTION DEBLUR to reduce motion blur in certain indoor environments. Noise or color rolling can increase.
MODE RETURN
DC
INDOOR RET
2-2. MANUAL
(default: NORMAL) : Horizontal wave or bar may be seen when MANUAL is selected and the camera is working under florescent or similar lights.
• NORMAL: Optimized for an indoor environment.
• DEBLUR: ON enables MOTION DEBLUR to reduce motion blur in certain indoor environments. Noise or color rolling can increase.
MANUAL
MODE RETURN NORMAL RET
3. FOCUS ASSIST
Usually cameras are installed in the day time and they often become OUT OF FOCUS at night time and IN FOCUS again when day time occurs.
This problem can occur on any camera regardless of type or manufacturer.
FOCUS ASSIST menu is the unique and patented feature that prevents the wrong focus and helps the focusing by simulating DAY & NIGHT conditions. Set zoom first and adjust focusing while switching between DAY & NIGHT.
FOCUS ASSIST
• DN DWELL (5s) : ICR switcher switches DAY & NIGHT at interval of D/N DWELL to help focus in DAY and NIGHT mode.
Further simulations are performed internally during switching.
DN DWELL POP ON FOCUS RETURN 5s OFF RET FOCUSING STATUS
12 13
Operating Instructions • POP ON FOCUS (OFF) : ON zooms in the center of picture at 2X for better focusing.
• FOCUSING STATUS (ON) : Shows how focus is set. When blue bar doesn’t show up, try the lens focus NEAR and FAR. The maximum blue bar indicates the best focusing position.
4. SCENE ENHANCE
4-1. NORMAL
(default) : Optimized for normal indoor and outdoor in good lighting condition.
4-2. WDR
: Improves the visibility for bright areas and dark areas by double capture of image with LONG and SHORT exposures. WDR level can be selected from LOW, MID and HIGH. Care should be taken to select this mode because video may lose its quality in some environments by over compensation.
※ CVBS video signal:Connecting 2nd video to CVBS port disables WDR function temporary. It should be considered when installer adjusts the video with installation monitor via CVBS video signal.
4-3. D-WDR
: Improves the visibility by compensating the video gain for the dark area. Noise can increase in the dark area accordingly.
4-4. BLC
: Improves the visibility for dark objects caused by bright back light. Outside area of BLC window can over saturate.
BLC has a target window for compensation and its size and position can be set by H-POS, V-POS, H-SIZE and V-SIZE.
4-5. HLC
: Cuts out the bright area with a black mask and excludes it from compensation. Lower HLC LEVEL cuts out video from lower light levels (more sensative).
5. 3D-NR
3D-NR is a very sophisticated and powerful time-based noise reduction technology by monitoring the noise for several video frames and defining and eliminating them consecutively at low light. Higher setting reduces more noise but results in losing the sharpness and tail effects or motion blur may occur.
13
Operating Instructions
6. DAY / NIGHT
DAY/NIGHT is used to control the setting during day-time and night-time operation.
Select the mode according to the lighting conditions and the camera type. SMART (DYNAMIC) IR can be set to reduce the saturation by strong IR illumination at night in any menu. Setting SMART (DYNAMIC) IR in any menu is identically applied to other menu. Zero(0) turns off SMART (DYNAMIC) IR and High setting decreases the saturation but the corners will be darker accordingly.
6-1. EXT
: DAY or NIGHT is determined by the built-in light photo sensor.
Camera with IR LED must be set to EXT.
6-2. AUTO
: Used when DAY or NIGHT is determined by light level through the lens and DAY from/to NIGHT is switched automatically by the scene brightness. D↔N THRESHOLD, D↔N DELY and SMART IR can be set in the menu. When EXPOSURE>AGC is less than 10, DAY/NIGHT AUTO is disabled and forcibly switches to ___(DAY) to avoid malfunction. EXT, B/W (NIGHT) and COLOR(DAY) is independent on AGC level. When EXTERNAL IR LED is used with NON IR LED model, please set to IR LED MODE ON. • D↔N THRESHOLD (0~20): Sets the threshold level switching from/to DAY(color) or NIGHT(B/W). Setting at a low level makes the camera enter NIGHT at a lower light level.
High level makes camera exited NIGHT at higher light level.
• D↔N GAP (0~15): Sets the gap level switching from /to DAY(color) or NIGHT(B/W).
• D↔N DELAY (0~60s): Sets the delay time when the camera switches from/to DAY(color) or NIGHT(B/W).
DAY/NIGHT AUTO
D<->N THRESHOLD D<->N GAP D<->N DELAY SMART IR RETURN |:::::::|::::::| 10 |:::::::|::::::| 10 5s |:::::::|::::::| 10 RET • SMART IR : SMART IR can be set to reduce the saturation by strong IR illumination at night in any menu of EXT, AUTO and B/W(NIGHT). Setting SMART IR in
14 15
Operating Instructions any menu is identically applied to other menu. Zero(0) turns off SMART IR and high level avoids saturation but the corners will be darker accordingly.
6-3. B/W(NIGHT)
: Removes IR cut filter and switches to B/W regardless of light level.
6-4. COLOR(DAY)
: DAY/NIGHT is disabled and outputs color video.
6-5. COLOR D/N
: Color mode, optimized for night conditions. It is available to recognize colors of car, people and moving objects even at night. Parameters can be controllable & programmable according to circumstances. Application for bright circumstance at night such as downtown, civic area, street, mall etc.
Conventional COLOR mode in NIGHT COLOR D/N mode in NIGHT
7. PICT ADJUST
7-1. WHITE BAL
(default: ATW) : ATW, ATWext, ONE PUSH and MANUAL are available for the white balance modes.
PICTURE
WHITE BAL SHARPNESS COLOR GAIN GAMMA SHADING RETURN ATW |:::::::|::::::| 10 |:::::::|::::::| 10 0.50
OFF RET • ATW: White balance is continuously working along with the color temperature changes in the range of 2,000K~8,500K.
15
Operating Instructions • ATWext: White balance is continuously working along with the color temperature changes in the range of 1,800K~11,000K.
• ONE PUSH: White balance works only while ● is pressed.
• MANUAL: White balance is fixed to the settings by R_GAIN and B-GAIN. This mode can be used only when the color temperature does not vary.
7-2. SHARPNESS
(default: 10) : Adjusts the sharpness of video(0~20).
7-3. COLOR GAIN 7-4. GAMMA
(default: 10) (default: 0.5) : Adjusts the color level of video(0~20).
: Adjusts the gamma of video.
7-5. SHADING
(default: OFF) : ON enables to compensate shading caused by wide lens setting.
8. SPECIAL
SPECIAL
MIRROR/FLIP PRIVACY MOTION PIXEL DEFECT TITLE SET DISPLAY DEFOG ZOOM MODE RETURN OFF OFF OFF OFF OFF OFF RET
8-1. MIRROR/FLIP
(default: OFF) : Reverses the video left and right and/or up and down by MIRROR/FLIP.
• OFF : Normal display without mirroring or flipping • Hor. : Video is reversed left and right • Ver. : Video is reversed upside down • HV : Video is reversed left and right and upside down.
When the video is reversed by Ver. or HV, then the joystick directions are reversed accordingly. This feature is very useful when a camera is installed upside down.
8-2. PRIVACY
(default: OFF) : Set the Privacy zones which can be enabled individually BOX or POLYGONS are available to mask the video.
8-2-1. BOX : Set area to select privacy zones by square.
16 17
Operating Instructions • ZONE NUM : Set a number to select a privacy zone from 1~10.
• ZONE DISP : ON enables a relevant privacy zone.
• H-POS, V-POS, H-SIZE and V-SIZE : Adjust the size and position of zone.
• COLOR : Select the color used for masking the zone form eight colors.
• TRANSPARENCY : Defines the transparency for the mask zone.
8-2-2. POLYGON : Set area to select privacy zones by polygon shape • ZONE NUM : Set a number to select a privacy zone from 1~4.
• ZONE DISP : ON enables a relevant privacy zone.
• COLOR : Select the color used for masking the zone form eight colors.
• TRANSPARENCY : Defines the transparency for the mask zone.
8-3. MOTION
(default: OFF) : MOTION can detect the changes in the motion window and displays the results in blocks and/or a text message.
MOTION
SENSITIVITY H-POS V-POS H-SIZE V-SIZE BLOCK DISP MOTION OSD SMART MOTION ZOOM STAY ZOOMING RETURN |:::::::|::::::| 10 10 5 40 25 OFF OFF OFF 5sec RET • SENSITIVITY : Adjusts the detection sensitivity for motion. Higher value increases the sensitivity to detect small motion easier. Too low of sensitivity will cause erratic detection.
• H-POS, V-POS, H-SIZE, V-SIZE: Adjust the size and position of the detection window.
• BLOCK DISP : ON enables to display the blocks for the detected area.
• MOTION OSD : ON enables to display a text message, MOVING !!!, • SMART MOTION ZOOM : ON enables to Automatic Zoom IN/OUT when motion is detected and also enables MOTION OSD to ON.
17
Operating Instructions Area to be zoomed in by SMART MOTION ZOOM can be set at SPECIAL> MOTION> SMART MOTION ZOOM>ZOOM TARGET. Adjusting • STAY ZOOMING : Sets the duration time for zooming by Motion.
◀ , ▶ (Joystick) for ZOOM TARGET varies the viewing angle to be zoomed when motion occurs. Set the video left and right and/or up and down by MIRROR/FLIP.
CAUTION
• SMART MOTION ZOOM does not work in low light conditions and BW.
• Set the direction of video by MIRROR/FLIP before SMART MOTION ZOOM setting. Otherwise ZOOM TARGET could be different from your intention.
8-4. PIXEL DEFECT
(default: OFF) : Detects and compensates the white pixels which become defective.
Once CALIBRATE is selected, the pixel calibration is initiated with lens closed and cannot be cancelled.
• THRESHOLD : Defines the level of detection. Be sure to set the value so that the pixels are uniformly blinking over the entire screen. Too low of a value will get a bad result because too many pixels are detected as bad pixels and the maximum number of pixels for compensation will be filled by the upper area.
• EXECUTE ‘ ☟’ : Long pressing will execute the pixel calibration for the detected pixels. Menu will exit automatically after compensation.
8-5. TITLE SET
: Camera title (name) can be set and edited up to 15 alpha numeric and symbolic characters from ASCII codes(ENGLISH only). ▲,▼, ◀ , ▶ moves the cursor to next input. Choose a character and ‘ for next input.
☟’ selects it. The selected characters are added and displayed on the top left Corner and the cursor moves right automatically • SP - Space is inserted when pressed ‘●’ • BS – Cursor moves back when pressed ‘●’ • CLR – Clears all the characters on input line when pressed ‘●’.
• POS – To be able to set the title position by ▲,▼, ◀ , ▶ and ●.
18 19
Operating Instructions
TITLE SET
A BCDEFGHIJKLMNOPQRST UVWXYZabcdefghijklmn o p q r s t u v w x y z , . ( ) { : [ ] 0123456789*+-/=l ! ? “ ‘ SP BS CLR POS RETURN
8-6. DISPLAY
: Enables or disables the OSD display.
• ID : ON enables to display the camera ID defined by SYSTEM>COMM.
SETUP>CAM ID.
• TITLE : ON enables camera ID display defined by SYSTEM>COMM.
SETUP>CAM ID.
• D-ZOOM RATIO : ON enables to display the zoom ratio on the bottom right corner. DZx.x will display the actual digital zoom ratio.
8-7. DEFOG
(default: OFF) • MODE - AUTO : Enhance foggy video automatically according to status of scene.
- MANUAL : Sets to enhance foggy video manually regardless of status of scene.
• LEVEL : MID, HIGH, LOW Video quality can be less in normal environments.
8-8. ZOOM MODE
(default: OFF) ON enables to select POINTING ZOOM, PRESET ZOOM or FLEX zoom modes.
8-8-1. POINTING ZOOM: • H-POINTER, V-POINTER - Able to set the location of zoom center D-Zoom is available DZ X1.1~ X8.0.
PRESET ZOOM
ZONE NUM ZONE VIEW H-POS V-POS D-ZOOM RATIO STAYING ZOOMING RETURN By Remote Controller only.
1 ON 5 5 DX2.0
3sec RET
19
Operating Instructions 8-8-2. PRESET ZOOM: Able to zoom into a preset area by PTZ controller.
• ZONE NUM : Set a number to select a preset zoom from 1~ 4.
• ZONE VIEW : ON enables a relevant preset zone.
• H-POS and V-POS : Adjust the size and position of a preset zone.
• D-ZOOM RATIO: Set the D-Zoom Ratio from DX 1.1~DX5.0
• STAYING ZOOMING : Sets the duration time for preset zoom area.
8-8-3. FLEX: Any area can be zoomed into by PTZ controller.
CAUTION
• Set the direction of video by MIRROR/FLIP before ZOOM MODE setting. Otherwise location of zoom center could be different from your intention.
• PRESET / FLEX ZOOM are available with RS-485 model only.
TIP
Setting for Zoom Function with PTZ Controller
● Enter the MENU : Press buttons 9+5+PSET (PRESET) ● Set the Preset Zoom : Press buttons 1(or ~4)+PSET (PRESET)
1
● Working the Flex Zoom : Moves the cursor UP/DOWN/LEFT/ RIGHT with Joy stick on the screen where you want the position to zoom in/out.
● D-Zoom IN: Press button TELE or Spin the joystick to clockwise.
● D-Zoom OUT: Press button WIDE or Spin the joystick to counter-clockwise.
● Select or Choose value in the MENU : Press button OPEN (IRIS OPEN) ● Exit the Preset/Flex Zoom mode : Press buttons 3+4+PSET (PRESET)
3 4 20 21
Operating Instructions
9. SYSTEM
SYSTEM
TV SYSTEM RESOLUTION COMM. SETUP LANGUAGE FACTORY DEFAULT RETUTN EU(PAL) 1080P ENG NO RET
9-1. TV SYSTEM
(default: US or EU) : Selects HDTV standards for US(60HZ) or EU(50HZ). By this selection, 2nd analog video output switches to NTSC or PAL accordingly.
9-2. RESOLUTION
(default: 1080P) : Three resolutions,1080P/720P(SCALED)/720P(CROPPED) are available. 1080P outputs 1920x1080 video at the frame rate of 30P/25P. 720P(SCALED) Image is scaled down from 1080P and outputs 1280x720 video without loss of field of view at the frame rate of 30P/25P.
720P(CROPPED) image is cropped at the center area from the image sensor and outputs 1280x720 video at the frame rate at 60P/50P but the image refresh rate is 30P/25P. Cropped image has narrowed field of view
9-3. COMM. SET UP
: COMM. SETUP defines the CAM ID, BAUD RATE and PROTOCOL. Data length, stop bit and parity are fixed to 8bit, 1stop bit and no parity bit.
• CAM ID – Assigns the camera ID from 1~255 for the comm. address.
• BAUD RATE – Selects the baud rate from 2400~115200.
• PROTOCOL – Selects the comm. Protocol from PELCO-D/P or VISCA.
(available with RS-485 model only)
9-4. LANGUAGE
(default: ENG) : 8 languages are available ENGLISH, JAPANESE, GERMAN, FRENCH, ITALIAN, SPANISH, POLISH and TURKISH.
9-5. FACTORY DEFAULT
(default: NO) : RECALL ☟ roads and saves the factory defaults.
21
Operating Instructions
Detail Function Description
▐ SMART MOTION ZOOM
SMART MOTION ZOOM enlarges the area defined by a yellow window to a full size image when motion is detected in the black window.
SMART MOTION ZOOM window can be re-sized by adjusting D-ZOOM RATIO and moved by H-POS and V-POS UNLIKE the conventional zoom which can zoom in/out the center area of image only, SMART MOTION ZOOM differentiates its usefulness from others. That is, a conventional camera installed in the corner of the ceiling can zoom the center of the floor in a room and result in losing the image of a door on the side wall. However, SMART MOTION ZOOM can be set to see the door side and zoom in that area without missing the IMPORTANT security point.
SMART MOTION ZOOM
ZONE VIEW H-POS V-POS D-ZOOM RATIO MOTION CHK CUNT RETURN OFF 10 10 DX2.0
3 RET • H-POS (10) - Moves MOTION ZOOM area(Yellow window) horizontally • V-POS (10) - Moves MOTION ZOOM area(Yellow window) vertically • D-ZOOM RATIO (DX2.0) - Sets the area size to be Digitally zoomed when motion occurs in the black window • MOTION CHK COUNT (2) - SMART MOTION ZOOM is activated after the motion in MOTION CHK COUNT are detected in a certain period.
For example, SMART MOTION ZOOM is activated after set # of triggers by motion.
22 23
Operating Instructions
▐ POINTING ZOOM
• available with RS-485 model only This camera has a very useful and powerful feature, POINTING ZOOM, which can zoom in/out any area.
POINTING ZOOM is the ability to zoom into an off center location using the PTZ Zoom in/out feature when connected via RS485 Use H-POINTER and V-POINTER to move the Yellow box to set the position of the center of the Zoom.
UNLIKE the conventional zoom which can zoom in/out the center area of image only, the flexible zoom location and area, POINTING ZOOM differentiates its usefulness from others.
That is, a conventional camera installed in the corner of the ceiling can zoom the center of the floor in a room and result in losing the image of door on the side wall. However, POINTING ZOOM can be set to see the door side and zoom in that area without missing the IMPORTANT security point.
POINTING ZOOM
H-POINTER V-POINTER RETURN 10 10 RET • H-POINTER (10): Sets the horizontal location of area to be zoomed by POINTING ZOOM.
• V-POINTER (10): Sets the vertical location of area to be zoomed by POINTING ZOOM.
23
Operating Instructions
* SMART MOTION and POINTING ZOOM VS. Conventional Zoom
Smart Motion and Pointing Zoom Conventional Zoom
24 25
Detailed Specifications
Sensor Resolution S/N Video Output Lens Smart Motion Zoom Digital Zoom Minimum Illumination Day/Night Electronic shutter speed White Balance Brightness DSS (Sens-Up) DNR WDR Privacy Zones Motion Detection ACE (Adaptive Color Enhancement) Advanced OSD Functions HD Transmission Range Operating Conditions Input Voltage Power Consumption (12VDC) Power Consumption (24VAC) Dimensions Panasonic 1/3” Progressive Scan CMOS Sensor 2.1 MegaPixel (1080p / 720p) More than 52 dB (AGC Off) Selectable: 1x HD-SDI (BNC) / EX-SDI (BNC) and 1x SD CVBS (BNC) CS Mount Lens Support (Not Included) YES 1.1x ~ 8x 0.0005 Lux (@AGC Max. DSS x2) TDN with dual filter switch Auto (1/ 30sec ~ 1/ 60,000sec) ATW / ATWext / One Push / Manual YES OFF / AUTO / X2 ~ X32 3D-DNR True WDR (Dual Scan) at 30fps YES (10 Zones) YES YES Smart Motion Zoom, Focus Assist, Motion Detection, Privacy Mask, Defog, D-Zoom(~8x), Sens-up(~x32), BLC/HLC, Title Set, Pixel Defect Compensation, Lens Shade Compensation Over 1000’ (Depending on cable characteristics and integrity) 14°-122°F (-10°-50°C) < 80% RH 12VDC / 24VAC (Dual Voltage) 250mA (3Watt) 230mA (2.8Watt) 1.89” x 2.09” x 2.89” (W x H x D)
25
COnSIDER THESE OTHER GREaT PRODuCTS fROM VT-HDOCE Series On Cue Series 4, 8, and 16 Channel Real Time 1080p EX-SDI Digital Video Recorders
• 4, 8 OR 16 CH EX-SDI / Analog Inputs (hybrid) with Full 1080p Camera Support • Now Supporting Cable distance of up to 1000’ using RG59!* • Hybrid Operation over COAX for HD-SDI, 960H, and D1 Cameras • Simple plug and play, point-to-point connection from camera to DVR • Real Time Recording on all channels at 1080p (VT-HDOC4E: 120fps), (VT-HDOC8E: 240fps), (VT-HDOC16E: 480fps) • HDMI, VGA, and Spot BNC Outputs • Up to 5 Internal SATA2/SATA3 HDD Slots supporting up to 20TB (5 x 4TB HDD) using Advanced HDD Format • External SATA Port (eSATA) Supporting up to 5x External via eSATA • Pentaplex Operation (Playback, Recording, Backup, Network) • Alarm In/Out • Per channel Image Adjustment • 4 Channel Audio In • 32 x 24 Motion Detection Grid • Multi channel Spot output • Panorama (Thumbnail) Search • Remote Viewing via CMS Software, Internet Explorer, and Mobile Phones (iOS/ Android), Mac OSX App • Linear digital zoom for live and playback • Up to 7 Simultaneous Network/Remote Connections • 256 Camera Remote Viewing via CMS Software • RS485 Communication port
26 27
COnSIDER THESE OTHER GREaT PRODuCTS fROM VT-HD/EXD1 EX-SDI Extender
• Use with standard HD-SDI cameras for extended range beyond 1000’ over RG59U 95% copper Coax. (Not needed with EX-SDI version cameras).
• Extended Serial Digital Interface • Powered by VLC (Visually Lossless Codec) Technology • Transmits up to 270Mbps • Backwards compatible with HD-SDI • Supports 1080P, 1080i, 720P, NTSC/PAL Video Signals • Compact size for easy, discreet installation • 12VDC Operation
27
28 29
29
30 31
LIMITED PRODUCT WARRANTY
VITEK products carry a three (3) year limited warranty. VITEK warrants rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a purchase by the end user. This warranty is nontransferable and extends Reseller.
The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, The product must not have been tampered with in any way or the guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
VITEK makes no warranty or guarantee whatsoever with respect to VITEK Authorized Reseller.
31
28492 Constellation Road ValenCia, Ca 91355 WWW.ViteKCCtV.CoM
Version 1.0
November 2015
advertisement
Related manuals
advertisement