Hama 00053179 N750 Dual Band WLAN Router, 2.4/5 GHz Owner Manual

 WLAN Router
»Wireless LAN 450 Mbps«
Instruction manual
00053179
Original user manual
Table of Contents
Introduction ................... 3
Foreword .............. vu. 3
Information on this user manual .. 3
Liability disclaimer ............. 3
Warnings. .....e—.—ee-reemmeoemmeno A
Copyright . .................... 5
Intended use. .................. 5
Safety ........................ 6
Danger of electric current. ....... 6
Fundamental safety precautions .. 6
Description.................... 8
Back of the device.............. 8
StatusLEDs ................... 9
Installation ................... 11
Safety information............. 11
Unpacking ................... 11
Checking contents and packaging11
Disposing of the packaging ..... 12
Aligning the WLAN antennas .... 12
Requirements for operation ..... 12
Requirements for the place of opera-
tion .............. 0a 13
Connection of the LAN-cables .. . 13
Connecting the WAN cable...... 13
Electrical connection. .......... 14
Connecting the mains adapter... 14
Checking the installation ....... 14
Configuration and operation ....15
PC configuration .............. 15
Configuring the IP address. . . .. 15
Configuring of the device ....... 17
Starting the configuration interface
17
Login ..................... 17
Selecting the menu language. . . 18
Configuring the Internet connection
18
LAN settings. ............... 24
Wireless LAN settings ........ 27
Setting the Wireless LAN encryption
37
Access control .............. 42
Automatic WPS configuration ..43
WLAN time control ........... 44
Specifying a new password . ... 45
TOO)S en 46
Configuration tool. ........... 46
Firmware update ............ 47
Restoring the default settings . . . 49
Status information............. 49
Troubleshooting. .............. 50
Troubleshooting chart. ......... 50
Appendix ........oeeerenecnoa 52
Support and contact information . 52
Notes on disposal ............. 52
Notes on the EC Declaration of Con-
formity....................... 52
Operating restrictions. ......... 53
Technicaldata ..................
54
WLAN Router 450
Introduction
Introduction
Foreword
Dear Customer,
By purchasing this WLAN router, you have decided in favour of a
quality product from Hama which corresponds to the latest state of
development with respect to technology and functional performance.
Please read the information contained in this booklet to familiarise
yourself quickly with the device and be able to make full use of its
functions.
We wish you a lot of pleasure with the device.
Information on this user manual
This instruction manual forms an integral part of the WLAN Router
WIRELESS LAN 450 Mbps (hereinafter referred to as device)
and contains important information on the intended use, safety,
connection and operation of the device.
The user manual must be kept near to the device at all times. It must
be read and observed by all persons using the device or eliminating
faults in the device.
Keep this user manual in a safe place and pass it on to any future
owners together with the device.
Liability disclaimer
All technical information, data and instructions on installation, opera-
tion of the device contained in this user manual represent the current
status at the time of printing and are based on the best possible
knowledge gained by experience and know-how.
The manufacturer assumes no liability for damage or injury result-
ing from failure to observe the user manual, use for other than the
intended purpose, unprofessional repairs, unauthorised modifications
or use of non-approved spare parts.
WLAN Router 450
Introduction
Warnings
The following warnings are used in this user manual:
/\ DANGER
A warning of this category indicates an impending dangerous
situation.
If the dangerous situation is not avoided, it may lead to serious
injury or even death.
» Follow the instructions in this warning to avoid the danger of
serious injury or even death.
À WARNING
A warning of this category indicates a potentially dangerous
situation.
If the dangerous situation is not avoided, it may lead to injuries.
» Follow the instructions in this warning to avoid the risk of injury.
A warning of this category indicates potential material dam-
age.
If the situation is not avoided, it may lead to material damage.
» Follow the instructions in this warning to avoid material damage.
» A note contains additional information to simplify the use of the
appliance.
4 WLAN Router 450
Introduction
Copyright
This documentation is protected by copyright.
Any duplication or reprinting, in whole or in part as well as reproduc-
tion of any illustrations, even in modified form, is only permitted with
the written approval of the manufacturer.
It is forbidden by law to copy, broadcast, display, transmit via cable,
play back in public or hire out material protected by copyright without
the consent of the copyright owner.
Unless otherwise indicated, all trademarks and logos mentioned
are trademarks of Hama GmbH and are protected by law. Microsoft,
Windows and the Windows logo are trademarks of Microsoft Corpo-
ration. All other product and company names are trademarks of the
respective owner.
Intended use
This device is intended as a base station for establishing a wireless
network and for joint Internet access in closed rooms.
Any use other than previously stated is considered as improper use.
/\ WARNING
Danger from use for other than the intended purpose!
If not used for its intended purpose and/or used in any other way,
the appliance may be or become a source of danger.
» Only use the appliance for its intended purpose.
» Observe the procedures described in this user manual.
No claims of any kind will be accepted for damage resulting from use
of the appliance for other than its intended purpose.
The risk must be borne solely by the user
WLAN Router 450 9
Safety
Safety
This device complies with the prescribed safety regulations. How-
ever, improper use can result in personal injury and/or damage to the
device.
Danger of electric current
/\ DANGER
Danger to life from electric current!
Contact with live wires or components can lead to serious
injury or even death!
Observe the following safety precautions to avoid danger from
electric current:
» Do not use this device if the mains adapter, power cable or plug
is damaged.
» Do not open the housing of the appliance. Danger from electric
current if live connections are touched and/or the electrical and
mechanical configuration is changed.
Fundamental safety precautions
Observe the following safety instructions to ensure safe handling of
the device:
m Inspect the appliance for visible signs of damage before use. Do
not use a damaged device.
m Do not allow children to play with the device.
m Persons who are unable to operate the device due to their physi-
cal, mental or motor response abilities may only use the device
under supervision or instruction by a responsible person.
WLAN Router 450
Safety
m Never open the device. Unauthorised opening and repairs can
lead to considerable danger for the user of the device. Only allow
qualified persons to carry out repairs. Improper repairs will invali-
date the guarantee.
m Repairs to the device during the guarantee period may only be
carried out by service centres authorised by the manufacturer,
otherwise the guarantee will become invalid in the event of dam-
age or subsequent damage.
m Defective parts may only be replaced with original spare parts.
Only original spare parts guarantee that the safety requirements
are met.
m Protect the device against moisture and penetration by liquids. If
the device comes into contact with liquids, disconnect it from the
power supply immediately.
m Do not operate the device in extremely dusty environments or in
the vicinity of heat sources.
m Clean the housing of the device with a slightly damp cloth. Do not
use any aggressive or abrasive cleaning agents or solvents.
m Do not pull the power cable to remove the plug from the mains
socket.
m Do not place any objects on the device.
m Electronic devices are delicate so avoid knocks and blows.
m Disconnect the plug from the mains socket in the event of faults
or during thunderstorms.
WLAN Router 450 7
Description
Description
Back of the device
| IT
|| ||
| 1 | 1 | 1
| asf
© WLAN antennas:
They allow devices such as PCs, notebooks, mobile tel-
ephones or PDAs to make wireless contact with the device.
@© | WLAN ON/OFF:
For switching off the WLAN function (e.g. over night).
Cabled LAN interfaces are not affected.
€) | Reset/WPS:
The Reset/WPS button has two functions:
m Holding the button depressed (10 seconds) resets the
device to the default settings.
m Pressing briefly allows devices to be added to an existing
network.
о LAN sockets 1-4:
For connecting devices such as PCs or notebooks via a LAN
cable.
6 WAN port:
For connecting to a broadband modem or other router.
@ 12V DC socket:
For connecting the mains adapter.
8 WLAN Router 450
Description
Status LEDs
on Mains adapter is connected and sup-
O | Power plying power.
Off No mains adapter connected, no
power supply to the device.
On 2.4 GHz wireless LAN is activated.
2 4G Off 2.4 GHz wireless LAN is not activated.
Flashin Wireless LAN is activated / data is be-
© 9 ing transmitted.
On 5 GHz wireless LAN is activated.
5G Off 5 GHz wireless LAN is not activated.
Flashin Wireless LAN is activated / data is be-
9 ing transmitted.
WLAN Router 450
Description
10
The WAN port has established a net-
WAN On work connection properly.
LNK/ACT | Off No connection
Flashing | Data transfer via WAN port.
WAN On Gigabit WAN connection activated.
1000M Off Gigabit WAN connection not activated.
The corresponding LAN port has
On established a network connection
LAN 1-4 properly.
CNK/ACT | off No connection
Flashing | Data transfer via respective LAN port.
LAN 1-4 | On Gigabit LAN connection activated.
1000M Off Gigabit LAN connection not activated.
WLAN Router 450
Installation
Installation
Safety information
/A DANGER
Personal injuries and damage to property may occur when
starting up the device!
Observe the following safety precautions to avoid the dangers:
» Never play with packaging material. Risk of suffocation.
» Pay attention to the instructions on the requirements for the
setup location as well as the electrical connection of the device
to avoid injury or damage to property.
Unpacking
+ Remove all parts of the device and the user manual from the
box.
€ Remove all packing materials from the device before using for
the first time.
Checking contents and packaging
The device is supplied as standard with the following components:
Broadband router
Mains adapter
Network cable
Short user manual
CD-ROM with user manual
» Check for visible signs of damage or missing items on delivery.
Report incomplete or damaged items to your supplier/retailer
immediately.
WLAN Router 450 11
Installation
Disposing of the packaging
The packaging protects the device from transport damage. The pack-
aging materials have been selected according to environmental and
waste disposal aspects and can therefore be recycled.
(NY Recycling the packaging material for further use saves raw materials
and reduces waste. When no longer required, dispose of the packag-
e ing materials according to local environmental regulations.
» If possible, keep the original packaging during the guarantee
period in order to be able to pack the appliance properly in the
event of a guarantee claim.
Aligning the WLAN antennas
Ф Align the antennas by turning them upwards.
Requirements for operation
The following conditions must be satisfied for installation and opera-
tion of the device:
12
The TCP/IP protocol must be installed on all PCs.
The web browser must support java script (e. g., Mozilla Firefox or
Microsoft Internet Explorer).
An Internet account with an Internet service provider and a DSL
connection are necessary for Internet access.
All devices employed must comply with the IEEE 802.11a, IEEE
802.11b, IEEE 802.11g or IEEE 802.11n standards.
WLAN Router 450
Installation
Requirements for the place of operation
For safe and trouble-free operation of the appliance, the place of
operation must satisfy the following requirements:
m Place the device at a central location where there are the least
possible obstacles between the device and the PCs.
m Do not install the device in the vicinity of metallic objects and
other electrical or radiating devices.
» Try to eliminate the interference sources, such as DECT
telephones, mobile phones, Bluetooth devices or other
WLAN networks.
D If this is not possible, a change of channel can also remedy
the problem.
m Do not expose the device to direct sunlight.
m The mains socket must be easily accessible so that the mains
adapter can be quickly unplugged in the event of an emergency.
Connection of the LAN-cables
€ Connect the computer and other network devices such as a hub/
switch to LAN sockets 1-4. Use a commercially available network
cable (twisted pair). The built-in switch automatically detects a
transmission speed of 10, 100 or 1000 Mbps, half/full duplex and
the cable type.
Connecting the WAN cable
€ Connect the Ethernet port of your modem to the WAN port @ on
the device. Use the cable that was supplied with your modem. If
a cable was not supplied, use a commercially available network
cable.
WLAN Router 450 13
Installation
Electrical connection
For safe and trouble-free operation of the appliance, the following
instructions on the electrical connection must be be observed:
m The device is supplied with 12 Volt DC voltage via the mains
adapter supplied. Always use the mains adapter supplied to con-
nect the device to the mains supply.
m Before connecting the device, compare the connection data (volt-
age and frequency) on the rating plate with those of your mains
adapter. The data must correspond in order to avoid damage to
the appliance.
m Protect the adapter cable from hot surfaces and sharp edges.
m Make sure that the power cable is not stretched tightly or twisted.
m Do not allow the adapter cable to hang over edges (danger of
tripping).
m If the device is not to be used for a longer period of time, discon-
nect the mains adapter from the mains supply.
Connecting the mains adapter
€ Connect the plug of the mains adapter to the 12 VDC jack @ of
the device.
@ Insert the mains adapter into the mains socket.
Checking the installation
m The Power LED should light up.
m ALAN LED should light up for each LAN (PC) connection (pro-
vided the PC is switched on).
m The WLAN LED should light up when the WLAN is activated.
m The WAN LED should light up when the modem is switched on.
Further information can be found in section Status LEDs.
14 WLAN Router 450
Configuration and operation
Configuration and operation
PC configuration
Configuring the IP address
The IP address 192.168.2.1 and an activated DHCP server are
preconfigured for the device as standard. This ensures that the in-
terfaced PCs are automatically assigned appropriate addresses and
further settings. We recommend that this setting is retained.
Proceed as follows to check the settings on your PC:
€ Select Start -> Control panel -> Network connections
EX... —
ue — Bere Dele | В drama pmb | - о LA
Hoa a E TTT Spe
с Express Euverriiada =) Br Hot e a a =
: =
si = | fa ire В =
===" COn Dem Me
[In site non cs (У Родила ле shades 4 cc CPE
[EJ en reo css e Cruda ind Pasante и
|] prt cb scam 2005 id Fo red Bape e REE 2 E
i
ate Mene £5 tisane e--
[№] еее оне Ward 200
Bln Progam +
E sde | [] ось
€ Select your LAN network connection.
Adresse [AS Metzwerkverbindungen
LAN oder Hoschesci fig met
Netrwuerksulgaben
WLAN Router 450 15
Configuration and operation
€ Click the corresponding network connection with the right mouse
button and select "Properties".
MT [e e an LAN- Verbindung
Algemer | Erweitert |
Verbindung henbelen über
[= NVIDIA nForce 10100 Mbps Hetero: | Kontguierar.. |
Die Yierbandung venwendel Bolgsrde Elsmenle:
2] =
$) Сава ed Diuckaimiogabe fa Mcinsol Netzweke a
м Alu Pakelplaner
м [a res yt ción fe Del [TCPAS
ч | | E
Instaieren | | Demas | Eigenschaften |
Beschreibung i
TCPAP. das Skarafaidorclokoll [i Wok -Neloperke, das dan
Matze mmoghchi
Symbol bei abc) er Infoberach avenger
FE diese Verhindung eingeschranite oder
Kab Corner best
OF | Abbrechen |
€ Select "Internet protocol (TCP/IP)" and click "Properties".
LT Te ET ER TEE EE rar aa a ра пела! О ОД
Algeneis | Alemaive Korfiguiation |
IP Eiretefungers bürnen aitoratsch zugevdecer Weder, were cie
Неее, dishes Funklion uberis. Werden Se sich andeinlall: an
den Helzwerkadministator, . Un de geegnsten IP-Emsisungsn oz
¡Podras automalisch bétshen
D Fogerde PAdresce verwenden
Subne zas
f+ DAS-Semeradierre aulomatsch berehen
E Folgerda DNS-Servaladrecer: vemveerder
Georg DN ES
=
——
== |
2 =
Emvebar.
[ок] внесет |
€ Select "Automatic retrieval of IP address" and "Automatic re-
trieval of DNS server address".
€ Then confirm with "OK" and confirm again in the following win-
dow with "OK".
Your PC is now configured to retrieve its IP address automatically
from the router.
16
WLAN Router 450
Configuration and operation
Configuring of the device
Starting the configuration interface
The device is configured using a web browser (Microsoft Internet
Explorer, Mozilla Firefox, etc.).
Proceed as follows:
Ф Boot your PC after installing the device in your LAN. If your PC is
already switched on, reboot.
Ф Start your web browser.
€ Enter the address: http://192.168.2.1 or "hama. router".
Login
After starting the configuration interface of the device, the login win-
dow appears in the web browser.
x
© http: //192, 168.2. 1 verlangt einen Benutzernamen und en Passwort. Ausgabe der Website:
"Default: admin/123456"
Benutrername: | =
Passwort: | «+...
[ox | _Abbrechen |
@ Enter admin into the "User name" field.
@ Enter 123456 into the "Password" field.
Ф After entering, click "OK" to log onto the device.
After successful login, the configuration interface (home page) of the
device is displayed:
hama | PEE KT | 7 Sa
E =
e] | a dm | ii | Bn swan
Ranier
“sue ] or Sara cr na ala es pie al Vs: Fer
AR ый о gy [LE o EE
Æinrichraisg
FE eb | e les Epa mrp ned emer Pastas, Sa
eri Herr E As Ly
Fara ang man a Pa a EYEE
| tous
Cet a an ma nar a мл
т Вере ЕН
Seria |
fosses ea frs ct pa y Pa rd Aa suey
Feira irar a
WLAN Router 450
Configuration and operation
Selecting the menu language
$ Select between the German, English and French languages on
the top right of the home page. The language is set immediately
and can be subsequently changed at any time.
Dia passanda Losing Fo
Газы =] Startseite | Einrichnung | Status | Werkzeuge
Configuring the Internet connection
18
You can use the integrated assistant to configure a device quickly.
Ф To start the configuration assistant, click the "Quick Setup" button
on the home page.
Time zone
hama.
©} Ч, Теле Zone
i 2 WEN Type
© 1. IP Address info Set the fimo zona olihe Wireless Roster, This information is used tor log emides and fraevll settnge
God WLAN Selnge
©) 6. Password Setings
Time Zone q
| Пе ое: at Amsterdam Berlin, Beam. Rome, Stockholm, Vienna
57 Auto; From Iaet Sunday In March 3:00 11 last Sunday in Octob
$ Select the correct time zone e.g., "(GMT +00:00) Greenwich
Mean Time: Dublin, Edinburgh, Lisbon, London” for Great Britain.
€ Enter the IP address of the time server for automatic time and
date setting here. This normally not necessary. However, if the
preset time server should go offline, you can receive a new one
via http://www.ntp.org.
Ф Activate the automatic summertime setting or an individual sum-
mertime setting with a preselected start and end time.
® Click the "Next" button to proceed.
WLAN Router 450
Configuration and operation
WAN type
€ Select a WAN connection type
Type Details
Your IP address is assigned automatically
Cable modem on establishment of the connection to
your ISP (Internet Service Provider).
Your ISP assigns you a permanent IP
Static IP DSL address.
The IP address is normally assigned auto-
PPPoE DSL matically. Your ISP assigns you a pass-
word and a user name.
The IP address is generally assigned
automatically, but it can also be static
(permanent). Your ISP assigns you a local
IP, a remote IP and a connection ID.
PPTP DSL
The IP address is generally assigned
automatically, but it can also be static
L2TP DSL (permanent). Your ISP assigns you a
password, a user name and an L2TP IP
address.
The IP address is assigned automatically.
Telstra Big Pond Big Pond assigns you a password and a
user name. (Australia only)
WLAN Router 450 19
Configuration and operation
IP address information
In the next view, enter the access data for your Internet provider. This
information can be either found in your documentation or obtained
directly from the provider. In view of the widespread use of DSL over
PPPoE, the rest of this description relates to this type of connection.
€ Enter your:
m User name,
m password and
m service name (not always necessary).
hama.
© 1. Time Zone
C 2 WAN Typa 3. IP Address Info 4
© 1.19 Address Ino PPPoE
4 WLAN Settings Enter the User Name and Password required by your ISP in the spprapriats fislds. ¥ yo
© 5 Password Settings A blank
|
|
E
Connection Type: [Continuous =] Connect | Dis
NOTE
Important note for T-Online users!
> Enter your T-Online access data into the user name field in the
following order:
[email protected]
A: 12 digits of your called line identification.
T: associated T-Online number.
M: 4-digit joint user suffix
D If your T-Online number consists of less than 12 digits, enter the
# character in front of the joint user suffix:
AAAAAAAAAAAATTTTTTTTTTT#@t-online.de
WLAN Router 450
Configuration and operation
In addition to the access data, the following can also be entered:
Input field Comments
MTU
(Maximum
Transmission Unit)
Enter here the maximum package size to be
transmitted. Values between 512 and 1492
are possible. If you not be sure about this
setting, leave the default value.
Connection type
Select here the dialling behaviour of your
device. You have the choice between:
m Continuous: the device is always con-
nected to the Internet. This connection
type is recommended if you have a flat
rate without time limit.
m Connect on demand: the device dials
in only when prompted by an connect-
ed computer, e.g. when you open the
browser on a computer. The connec-
tion is then maintained until the time
set under idle time has expired without
activity.
m Manual: you establish connection by
pressing the "Connect" button and ter-
minate the connection by pressing the
"Disconnect" button.
Idle time out
Specify here how many minutes inactivity
must elapse before the Internet connection
should be disconnected. Values between 1
and 1000 are possible.
€ Subsequently confirm with "Next".
WLAN Router 450
21
Configuration and operation
WLAN settings
You can change the name and the WLAN encryption in the following
view.
hama.
© 1. Time Zone
© 2 Wan Type 4. WLAN Settings
© 3 P Adds In ITTY =
|
© 4. VéLAN Settings
C 5 Password Selfings
CESE
Pre-Shared Hey :
__ Back |.
Type Details
Enter the name of the wireless LAN here.
The length of the SSID can be up to 32
SSID characters and must be the same for all
devices in the network.
Example: "WLAN_ Router 450Mbps"
Pre-Shared Key О your preferred key with the required
€ Click the "Next" button to proceed.
WLAN Router 450
Configuration and operation
Password configuration
The router configuration password can be changed in the following
view.
hama.
C 1. Time Zone
C2 WAN Type Password Settings 4
O 36 Address Ino You can change ihe passward required while legging into the vareless muler's ле В а
Ci 4. WLAN Settings Administrator as soon as possible, and store it in a safe place Passwords can contain |
© 5 Password Soltings
New Password | |
Confirm Password : |
BACK | APPLY | CANCEL
The password is set to "123456" by default. Change the password as
soon as possible and keep it in a safe place.
» Passwords can contain 6 to 30 alphanumeric characters.
> Pay attention to upper and lower case characters.
€ Enter a new password and confirm.
€ Then confirm the input with "Apply".
€ Click "Apply" in the next window. The device now requires ap-
prox. 60 seconds to restart and activate the settings.
The device is now been configured enough to access the Internet
with the connected computers.
NOTE
» In the case of volume or time tariffs, we recommend selecting
"Connection on demand" so that the Internet connection is auto-
matically disconnected after the set "idle time". In the case of a
permanent connection, high connection costs can otherwise be
incurred.
» Please note that closing the browser does not necessarily
disconnect from the Internet. A very large number of programs
send requests to the Internet or receive data without this being
obvious. This is an equivalent request for the device such as
opening the browser. If you wish to ensure that there is no ac-
tive connection to the Internet, you should switch off the device
or disconnect it from the modem.
WLAN Router 450 23
Configuration and operation
LAN settings
Various network settings can be made here. To change the standard
LAN settings, proceed as follows:
€ On the home page, click the button "General Setup" and then
select "LAN" in the menu on the left.
Zi а ыыы пал я |
hama.
O System
LAN 4
OWVAN
CLAN You can enable the Wireless Routers DHCP server to automatically alle
Network
I» Wake Оп Lan
02.4GHz Wireless pull EA —
IP Address : pg ra ОВ
OS5GHz Wireless ENTE EME [255 255 2550
02485 GHz ENT oe 1
0 dos ors [EEE
C NAT
; « DHCP Server
Travel Fo E
A [E (197 16932 100
DHCP Client End IP : [192 169 2 200
APPLY
= Static DHCP Lease Table
LAN IP
Input field Comments
The device is preset to the IP address
IP address 192.168.2.1. If you wish to use a different
address, enter another IP address here.
Enter the subnet mask here. Normally you
should enter 255.255.255. 0 here.
Select "Enable" if the IP addresses in your
network are managed by a DHCP server.
Select "Disable" if the IP addresses in your
network are assigned statically.
Subnet mask
DHCP server
24 WLAN Router 450
Configuration and operation
DHCP server
Input field Comments
Enter here how long the assigned IP ad-
Lease time dress is valid for the client.
Enter here the start of the IP address range
DHCP client start IP | from which the DHCP server may assign IP
addresses to the clients.
Enter here the end of the IP address range
DHCP client end IP | from which the DHCP server may assign IP
addresses to the clients.
Domain Name Enter the domain name here.
Static DHCP lease table
Here you have the possibility of assigning a fixed IP address from
valid range to a certain MAC address. If the client then logs in to the
device, it is always assigned this IP address.
Proceed as follows:
€ Enable "Static DHCP leases"
€ Enter the "MAC address" and the "IP address into the table.
$ Click the "Add" button to save the input to the table or "Clear" to
delete the input.
Saving settings
€ Confirm your inputs with "Apply".
Ф In the next window, click "Apply". The device now requires ap-
prox. 60 seconds to restart and activate the settings.
» After restarting, the new LAN configuration is valid. You
must use the new IP address to call up the web interface in
the browser.
WLAN Router 450 25
Configuration and operation
Wake On LAN (WOL)
Here you have the possibility to start a switched-off device via the
network. If necessary, the corresponding settings must be made on
the device to be switched on in order for the WOL to function.
O System
SWAN
© LAN
E Wake On Lan
02 4GHz Wireless
O5GHz Wireless
024&5GHz
0.005
Wake On Lan
DHCP Client List
IP Address | HostMame | MAC Address
Mona — =
Wake | Clear | Reset — | Refresh
@ Select the device to be switched on from the list of DHCP clients
by marking the box in the "Select" column.
+ + + +
Click on "Wake" to switch on the device.
Click on "Clear" to remove the device from the list.
Click on "Reset" to reset the device.
Click "Refresh" to add any newly detected devices to the list.
WLAN Router 450
Configuration and operation
Wireless LAN settings
The settings for the wireless LAN are made here. The device has two
WLAN units that work independently of each other: one for the 2.4
GHz standard frequency range; one for the 5 GHz frequency range.
That means that there are two WLAN configuration options.
Since the setting options for 5 GHz are identical to 2.4 GHz, The 2.4
GHz options will be described here in more detail. Differences to the
5 GHz settings will be dealt with separately.
To change the standard WLAN settings, proceed as follows:
€ On the home page, click the "General Setup" button and then
select "2.4 GHz Wireless" in the menu on the left.
Basic settings
€ Select "Basic settings" in the menu on the left.
€ Under "Mode", select the function that the device is to perform in
the network.
Mode Comments
This is the most-used operating mode.
Devices can be connected wirelessly to
Access Point each using a WLAN router and then estab-
lish connections to the Internet or to LAN
devices connected to the router.
The WLAN router can be connected to a
LAN device such as a television or game
Station console and acts as WLAN adapter for the
(infrastructure) device in order to connect to the WLAN. In
this mode, clients are not able to log in via a
wireless connection.
Connects two Ethernet LANs wirelessly to
each other. In this mode, clients are not
able to log in via a wireless connection.
AP Bridge -
Point-to-Point
WLAN Router 450 27
Configuration and operation
Mode Comments
. Connects several Ethernet LANs wirelessly
AP Bridge - . .
. 4 with each other. In this mode, clients are
Point-to-Multipoint € . )
not able to log in via a wireless connection.
Connects several Ethernet LANs wirelessly
AP bridge WDS with each other and clients are also able to
log in via a wireless connection.
Combines the access point mode and the
station mode and extends the wireless
range of existing WLANs by repeating the
signal.
Universal Repeater
The further configuration is dependent on the selected mode.
28 WLAN Router 450
Configuration and operation
Operating as access point (AP)
hama.
O System
O WAN
O LAN
C2 4GHz Wireless
[+ Basic Settings
L Advanced Settings
В Security Settings
E Access Control
E WES
O55GHr7 Wreless
amd BEALL
Basic Settings 4
This page allows vou to define ESSID. and Channel for the wreless connection Thesa paran
IR erro =
IY
ITE so sce cis |
APPLY с
Input field Comments
Band
Specify according to which standards the
device is to function in the 2.4 GHz range
(or 5 GHz range). (for details, see the
section Standards and their maximum
transfer rate).
SSID
Enter the name of the wireless LAN here.
The length of the SSID can be up to 32
characters and must be the same for all
devices in the network.
Example: "WLAN_ Router 450Mbps"
Channel number
Select the channel here, on which the data
is to be transmitted. (for details, see the
section Channel selection).
Associated clients
Switch on the control field "Show active
clients" to display all client computers that
are logged onto your access point.
€ Click on the "Apply" button to accept the settings.
WLAN Router 450
Configuration and operation
Operating as station (infrastructure)
hama.
O System
SWAN
S LAN
O2.4GHz Wireless
I+ Basic Settings
P Advanced Seitngs
E Security Settings
I: Access Corral
I WPS
O 5GHz Wireless
2.4 85 GHz
Basic Settings 4
This page allows vou 10 define ESSID, and Channel for the wireless connection. Thesa |
[Mode] | ation (Infrastructure! =]
se:
TENA ss]
APPLY
Input field Comments
Band
Specify according to which standards the
device is to function in the 2.4 GHz range
(or 5 GHz range). (for details, see the
section Standards and their maximum
transfer rate).
SSID
Enter the name of the wireless LAN here.
The length of the SSID can be up to 32
characters and must be the same for all
devices in the network.
Example: "WLAN_ Router 450Mbps"
Site Survey
Click on "Site Survey" to display a list of
wireless networks, with which the device
can establish a connection.
€ Click the "Apply" button to accept the settings.
30
WLAN Router 450
Configuration and operation
Operating as AP Bridge - Point-to-Point
hama.
O System
O WAN
Oo LAN
© 2.4GHz Wireless
L Basic Settimags
P Advanced Settings
b Security Settings
b Access Control
ÈWPS
О СНЕ Wireless
024 &5 GHz
Input field Comments
Band
Basic Settings 4
This page allows you to define ESSID, and Channel for the winless conneclion. These |
НИЕ ГР Bridge (Por io Painl) =|
ECT 7
ITT secu seins |
APPLY
Specify according to which standards the
device is to function in the 2.4 GHz range
(or 5 GHz range). (for details, see the
section Standards and their maximum
transfer rate).
Channel number
Select the channel here, on which the data
is to be transmitted. (for details, see the
section Channel selection).
Mac address 1
Enter the address of the access point here,
to which the bridge connection is to be
established.
Security
settings
Click this button to set the encryption for
your Wireless LAN.
The instructions for setting the wireless LAN
encryption can be found in section Setting
the Wireless LAN encryption.
€ Click the "Apply" button to accept the settings.
WLAN Router 450
31
Configuration and operation
32
Operating as AP Bridge - Point-to-Multipoint
hama.
1 Basic Settings 4
SWAN
О БАМ This page allows you 10 define ESSID, and Channel for the weeless connection. These |
02.4GHz Wireless IEE [+ ridge Point to Muti Faint) =]
В Security Settings gin E
у necesa Control ns EEE —
> ws ITER onion
0 5GHz Wireless [000000000000
02.455 GHz ac hae Er
0008 IEE Sea Satin |
The difference to AP Bridge - Point-to-Point operation is that you are
able to enter MAC addresses for several access points in this mode.
It is only possible to make a bridge connection to a maximum of 4
other access points.
Input field Comments
Specify according to which standards the
device is to function in the 2.4 GHz range
Band (or 5 GHz range). (for details, see the
section Standards and their maximum
transfer rate).
Select the channel here, on which the data
Channel number | is to be transmitted. (for details, see the
section Channel selection).
Enter the addresses of the access points
Mac addresses 1-4 | here, to which the bridge connection is to be
established.
Click this button to set the encryption for
your Wireless LAN.
The instructions for setting the wireless LAN
encryption can be found in section Setting
the Wireless LAN encryption.
Security
settings
€ Click the "Apply" button to accept the settings.
WLAN Router 450
Configuration and operation
Operating as AP Bridge WDS
hama.
O System
O WAN
OLAN
0 2.4GHz Wireless
F Basic Seilimgs
P Advanced Settings
b Security Settings
I+ Access Coral
WPS
O 5GHz Wireless
024 &5 GHz
odos
ONAT
O Firewall
Basic Settings 4
This page allows you to define ESSD, and Channel Tor the wireless connection. These |
ET Y
IY
Show Active Clients _|
ITT cece sei: |
WDS (Wireless Distribution System) is the term for the wireless
connection between several access points. In addition, it permits the
login of clients that other bridge operating modes do not allow. For
each additional access point, the bandwidth of the network is halved
because the packages have to be transmitted twice.
Comments
Input field
Band
Specify according to which standards the
device is to function in the 2.4 GHz range
(or 5 GHz range). (for details, see the
section Standards and their maximum
transfer rate).
SSID
Enter the name of the wireless LAN here.
The length of the SSID can be up to 32
characters and must be the same for all
devices in the network.
Example: "WLAN_ Router _54Mbps"
Channel number
Select the channel here, on which the data
is to be transmitted. (for details, see the
section Channel selection).
Associated clients
Switch on the control field "Show active
clients" to display all client computers that
are logged onto your access point.
WLAN Router 450
33
Configuration and operation
Input field Comments
Enter the addresses of the access points
Mac addresses 1-4 | here, to which the bridge connection is to be
established.
Click this button to set the encryption for
your Wireless LAN.
The instructions for setting the wireless LAN
encryption can be found in section Setting
the Wireless LAN encryption.
Security
settings
€ Click the "Apply" button to accept the settings.
34 WLAN Router 450
Configuration and operation
Operating as universal repeater
hama.
O System
O WAN
OLAN
OC 2.4GHz Wireless
F Basic Seflings
E Advanced Settings
I Security Settings
| Access Control
FF WPS
0 5GHz Wireless
024 &5 GHz
= = —
Basic Settings 4
This page allows you io define ESSID, and Channel for the vareless connection. These |
TS [очен чей
[о
ITT — sta Ace Cno |
IES Em
Ste Survey sto one]
Input field Comments
Band
Specify according to which standards the
device is to function in the 2.4 GHz range
(or 5 GHz range). (for details, see the
section Standards and their maximum
transfer rate).
SSID
Enter the name of the wireless LAN here.
The length of the SSID can be up to 32
characters and must be the same for all
devices in the network.
Example: "WLAN_ Router 450Mbps"
Channel number
Select the channel here, on which the data
is to be transmitted. (for details, see the
section Channel selection).
Associated clients
Switch on the control field "Show active
clients" to display all client computers that
are logged onto your access point.
Enter the name of the network here that is
Root AP SSID to be amplified by the device.
Click on "Site Survey" to display a list of
Site Survey wireless networks, with which the device
can establish a connection.
€ Click the "Apply" button to save the settings.
WLAN Router 450
35
Configuration and operation
36
Standards and their maximum transfer rate
Specify in the "Band" input field according to which standard the
device is to function.
The following is available for the 2.4 GHz frequency range:
m 2.4 GHz (B):
only 802.11b devices can connect to the router (maximum trans-
fer rate of 11 Mbps).
2.4 GHz (N):
only 802.11n devices can connect to the router (maximum trans-
fer rate of 300 Mbps).
2.4 GHz (B+G):
only 802.11b and 802.11g devices can connect to the router
(maximum transfer rate of 11 Mbps for 802.11b devices and 54
Mbps for 802.11g devices).
2.4 GHz (G):
only 802.11g can connect to the router (maximum transfer rate of
54 Mbps).
2.4 GHz (B+G+N):
802.11b, 802.11g and 802.11n devices can connect to the router
(maximum transfer rate of 11 Mbps for 802.11b devices and 54
Mbps for 802.11g devices; 300 Mbps for 802.11n devices).
The following is available for the 5 GHz frequency range:
m 5 GHz (A):
only 802.11a can connect to the router (maximum transfer rate of
54 Mbps).
5 GHz (N):
only 802.11n devices can connect to the router (maximum trans-
fer rate of 450 Mbps).
5 GHz (A+N):
802.11a and 802.11n devices can connect to the router (maxi-
mum transfer rate of 54 Mbps for 802.11a devices and; 450 Mbps
for 802.11n devices).
Channel selection
m 13 channels (1-13) are available in the 2.4 GHz frequency range.
m Channels 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112,
116, 120, 124, 128, 132, 136 and 140 are available in the 5 GHz
frequency range.
WLAN Router 450
Configuration and operation
Setting the Wireless LAN encryption
A distinction must be made between the following terms:
m Authentication:
is a process during which for example, the identity of a person is
determined by means of a certain feature. For example, this can
be a fingerprint, a password or another form of authorisation.
m Encryption:
is a process during which a "plain text" is transformed into a
"secret text" by means of an encryption routine (algorithm). One
or more codes can be used for this. Each individual encryption
method offers one or more possibilities for authentication.
» Encryption is switched on by default. For security reasons, it is
recommended to use your own WLAN key.
In addition to WPA, the device also supports the older method WEP
(Wired Equivalent Privacy). WEP is only necessary if all the client
computers in the wireless LAN are not able to use the WPA method.
» Be aware that the WEP method is now not considered to be
secure. lt is possible that WEP-encrypted data can be read and
manipulated by unauthorized third parties. We therefore recom-
mend not to use WEP and only use the secure WPA encryption
method.
WLAN Router 450 37
Configuration and operation
To set the Wireless LAN encryption, proceed as follows:
€ On the home page, click the "General Setup" button and then
select "2.4 GHz Wireless" in the menu on the left.
€ Select the mode under basic settings and confirm with "Apply".
€ Then select "Security settings" in the menu an the left.
Various different encryptions are available depending on the selected
mode:
m Disable
m Wired Equivalent Privacy (WEP) with 64 bit and 128 bit
m Wi-Fi Protected Access (WPA) Pre-Shared Key
x WPA RADIUS
Ф Select the encryption method and enter the corresponding data
according to the input mask (see following pages).
> Pay attention to upper and lower case characters when
entering the key.
@ In the next view, click on the "Apply" button and again on the
"Apply" button in the following view to save the settings.
The device will be restarted. After restarting, the wireless LAN is
available with encryption.
38 WLAN Router 450
Configuration and operation
Deactivating
Encryption is deactivated (not recommended).
Wired Equivalent Privacy (WEP)
hama.
O System
O WAN
SLAN
0 2.4GHz Wireless
I+ Basic Settings
I» Advanced Settings
b Security Settings
F Access Control
I= WHFS
0 5EGHz Wireless
92485 6Hr
ome yy
Security Settings 4
This page allows vou setup the wireless security. Tum on WERP or WEA by usmg Encr;
Encryption : [wer =]
Key Length : | ECE
Default Tx Kay : [Key 1 =]
Sela PTET eR | алллччееенн
Encryption Fay 1 : | EEN
Input field Comments
Select between a 64-bit or 128-bit encryp-
Key Length tion, whereby 128-bit offers more security.
Choose between:
Key Format m Hex (characters between 0-9 and a-f)
m ASCII (any characters)
It is possible to preset up to 4 keys.
Default
Tx Key € Select the key that you wish to
preset.
Encryption Key 1-4
Enter your preferred key in the required
length here.
Examples:
m 64-bit Hex (10 characters):
231074a6ef
m 64-bit ASCII (5 characters)
j31n!
m 128-bit Hex (26 characters)
231074a6b9773ce43f91a5bef3
m 128-bit ASCII (13 characters)
urlaub2006!+0
WLAN Router 450
39
Configuration and operation
Wi-Fi Protected Access (WPA) Pre-Shared Key
hama.
O System
у Security Settings +
O WAN
OLAN This page allows you setup he wireless secury. Turn an WEP a WPA by using Enc
C 2.4GHz Wireless [VIPA pre-shared key =]
e PAMKIP
ONCE WW F'WPAZAES
I+ Advanced Settings e !
p Security Settings ___ Pre-Shared Key Format : | ER
ETT |
EEE
E Arnao Paráml
Input field Comments
Choose between:
WPA Unicast Cipher | = WPA with TKIP encryption algorithm
Suite m WPA2 with AES encryption algorithm
m WPA2 Mixed Mode
Choose between:
m Passphrase, for a key with a length of
at least 8 and a maximum of 63 char-
acters, whereby letter (A-Z), numbers
and punctuation characters may be
used
m Hex for a key with a length of 64 char-
acters, whereby only characters from
0-9 and a-f may be used.
Pre-Shared Key
Format
Enter your preferred key with the required
Pre-Shared Key length here
40 WLAN Router 450
Configuration and operation
WPA RADIUS
hama.
0 System
O WAN
OLAN
0 2.4GHz Wireless
I: Basic Sethings
I Advanced Settings
I» Security Settings
E Access Control
I= WPS
2 56GHz Wireless
Security Settings 4
This page allows you setup (he wireless Securil Tum an VWEP or WEA by using Ener
es
DL ETC 1 OWPAMKIP) 1 WPAS(AES)
С
RAMHUS Server Password ; |
APPLY
Input field Comments
Choose between:
WPA Unicast Cipher | = WPA with TKIP encryption algorithm
Suite = WPA2 with AES encryption algorithm
m WPA2 Mixed
RADIUS server Enter the IP address of the RADIUS server
IP address here.
RADIUS Server Port
The RADIUS server port is preset to "1812".
RADIUS server
password
Enter the password for the RADIUS server
here.
WLAN Router 450
a1
Configuration and operation
42
Access control
This function prevents unauthorised users connecting to the device.
This means that only MAC those addresses obtain access that are
listed here.
Up to 50 MAC addresses can be listed in the "MAC Address Filtering
Table".
Proceed as follows:
€ On the home page, click the "General Setup" button and then
select "2.4 GHz Wireless" in the menu on the left.
@ Select "Access control" in the left menu.
hama.
O System
у Access Control
O VAN
o LAN For cecuily report Пе Убе ее Буа [ета MAL Addiess Filenng that п ай слег ВИЙ новая В
© 2.4GHz Wireless « MAC Address Fikoring Table
№ Basic Serias it aloes 50 entries only
I Advanced Settings L m0. | MAC Address | Comment ||
E Security Settings
Malaita
| Access Control —
y wr [ Enable Access Control
SGHz Wiless | NDS Is EE
92.48 5 GHr | | Ad
a
Input field Comments
Enter the MAC address of the device with-
Mac address .
out special characters here.
Enter a description here that will help you to
Comment identify the address later on.
€ Click on "Add" to add the specified MAC address to the MAC
address filter table.
€ Mark the "Enable Access Control" box to switch on the MAC ad-
dress filter.
Ф To remove a MAC address from the MAC address filter table,
mark the MAC address to be removed in the box in the "Select"
column (it is possible to mark more than one address) and click
"Delete". You can also click on "Delete all" to delete the entire
table.
$ Click the "Apply" button to save the settings.
WLAN Router 450
Configuration and operation
Automatic WPS configuration
WPS (WiFi Protected Setup) is a function that simplifies the security
configuration of the wireless LAN connection.
» To be able to use the function, the router/access point and the
remote device (WLAN USB Stick, PCI card or PCMCIA card)
must be equipped with the WPS function.
There are two ways of performing the security configuration:
m Configure by Push Button
m Configure by Client PinCode
Configuration with button
€ Briefly press the Reset/WPS button on the device.@.
+ Within 2 minutes, click button "Start PBC" under tab "WPS" in
the configuration program of the WLAN adapter.
Configuration with pin code
$ Note the pin code displayed in the configuration program of the
WLAN adapter.
Select the target network in the upper list and then click button
“Start PIN".
+
€ Switch to the user interface of the device and select Setup —
Wireless— WPS.
+
Enter the noted code in the input field for the pin code and click
"Start PIN" to start the transmission. The connection is now set
up automatically.
After successful connection, a profile is created that automatically
sets up the connection again after a restart.
WLAN Router 450 43
Configuration and operation
WLAN time control
This function enables you to set times for every week day, when the
WLAN is to be switched on or off.
Proceed as follows:
+
On the home page, click the button "General Setup” and then
select "2.4 & 5 GHz" in the menu on the left.
hama.
O System
Wireless Schedule
O VAN
© LAN
E Enable Wireless Schedule
"Sunday [Monday l Tuesday I Wednesday 1° Thursday Friday
0 2.4GHz Wireless EE несе [оо =] мене © [оо =
О 5EGHz Wireless ЕАО ini sn =] i
02,4 & 5 СНЕ A
bs oo eon | Mme Command
oO NAT RE MA
++ ++ oO
+
44
Mark the box to specify the weekdays, for which you wish to set
the time.
Enter the time in 24-hour format in hours and minutes.
Determine whether the WLAN is to be switched off or on at the
specified time.
Click "Add" to add the time to the list.
To remove the time from the list, mark the time to be removed in
the box in the "Select" column (it is possible to mark more than
one time) and click "Delete". You can also click on "Delete all" to
delete the entire list.
Mark the "Enable Wireless Schedule" box to switch on the auto-
matic time control.
Click the "Apply" button to save the settings.
WLAN Router 450
Configuration and operation
Specifying a new password
Assign a new password for access to the device to prevent unauthor-
ised access to the configuration menu. Proceed as follows:
€ On the home page, click on the "General Setup" button, select
"System" and finally "Password Settings" in the menu on the left.
hama.
© System
| Time Zone
b Password Settimgs
Password Settings 4
You can change the password required while logging ino the wireless routars web-base
Lhe pk il Administrator as soon as possible, and store it in a safe place. Passwords can contain
con ee
CLAN Hew Password : FO
0 2 4GHz Wireless LME
O 5GHz Wireless
02.4 & 5 GHz MEE ERE
O0nS
Input field Comments
Current Enter the current password here. The de-
password fault password is set to "123456".
New password Enter any new password here.
Repeat entry of the new password here to
Confirm password )
confirm.
€ Click the "Apply" button to save the settings.
WLAN Router 450 45
Configuration and operation
Tools
The device provides you with various tools to support you during
configuration and operation of the device.
Configuration tool
You can save the entire configuration of the device into a configura-
tion file.
Proceed as follows:
€ On the home page, click the "Tools" button and then select "Con-
figuration tools" in the menu on the left.
hama.
C Tools
& Configuration Tools
> Firmware Upgrade
Configuration Tools 4
у Use "Backup Seltings” fool lo save the Váreless Rówiers cumen? seitings lo a fle named “config
> Reset Wireless Router. Atemativealy vou can use 1he Resiore lo Factory Défaut” tool to force the Wii
— 6m |
HET owen ||
€ Click the "Save" button.
€ Select the target directory.
€ Choose a file name that enables it to be uniquely identified.
$ Click the "Save" button to save the settings.
If you wish to restore the saved settings at a later date:
@ Click the "Browse" button and then select the desired configura-
tion file.
€ Click the "Upload" button to load the file.
The device now takes a few seconds to upload the file and restart.
After restarting, the selected configuration is valid.
46 WLAN Router 450
Configuration and operation
Firmware update
€ On the home page, click the "Tools" button and then select
“Firmware upgrade" in the menu on the left.
Ф Click the "Next" button.
hama.
© Tools .
b Configuration Tools Firmware Upgrade ?
b Fi
Todo ae Thés tool allows you 1o upgrade the Wireless Routers system fimmware. Enter the path a
В Неве! confem the upgrade
| Durchsuchen. |
€ Enter the path and the firmware file name (.bin).
» It is possible to search for the corresponding file by clicking the
"Browse" button.
ATTENTION
Incorrect operation during firmware updating can render the
device unusable!
Please observe the following notes to avoid rendering the device
unusable during a firmware update.
» Ensure that the firmware file matches the device. If in doubt,
consult Hama product support.
> Before beginning a firmware update, establish connection to the
device via a cable if there is a risk of loss of WLAN connection
during data transmission.
» The device must not be disconnected from the mains supply
during updating.
WLAN Router 450 a7
Configuration and operation
48
€ Check the file details again and start updating by pressing the
"Apply" button.
€ You will then be prompted to confirm the update.
After successful updating, the device performs a restart.
> Loading a new firmware overwrites the previous settings.
Restarting the device
€ On the home page, click the "Tools" button and then select "Re-
set" in the menu on the left.
Da yb realy mis AEH 1SE Vines Healt
mee SR)
€ Click the "Apply" button to restart.
€ Click "OK" to confirm the following message.
The device will be restarted.
» Your settings remain unchanged.
WLAN Router 450
Configuration and operation
Restoring the default settings
You can restore the default settings so that the user name is re-
set to "admin", the password to "123456" and the IP address to
"192.168.2.1".
» All current configuration settings are deleted and the default set-
tings restored during this procedure.
Proceed as follows:
€ Press the Reset/WPS button.€) on the back of the device for 10
seconds until the POWER LED @ starts flashing.
The device is now reset to the default settings so that you can use
them to access the device via your web browser.
Status information
$ Click the "Status" button on the home page.
You can display information in various sub-menus on the Internet sta-
tus, device status or active DHCP clients in the menu on the left side.
A packet counter is available under the menu item "Statistics".
WLAN Router 450 49
Troubleshooting
Troubleshooting
Troubleshooting chart
Before sending the device to customer service, use the following
table to check whether you can remedy the problem yourself.
Error/Problem
Power LED @
does not light up.
The LAN LEDs
Pdo not light up.
It is not possi-
ble to establish
connection to the
device to config-
ure it.
Possible cause
Mains adapter not
connected correctly
No voltage from
the mains socket
Defective device
The LAN cables
are not properly
inserted.
The connected
devices are not
switched on.
LAN cable not con-
nected correctly
Wrong IP address
Wrong subnet
mask
Firewall software is
activated.
Remedy
Make sure the mains
adapter is plugged into
the mains socket and
correctly connected to
the device.
Check the fuses.
Contact customer serv-
ice.
Check the seating of the
plugs.
Switch on the connected
devices.
Check that the RJ-45
network cable is correctly
connected.
Make sure that the IP
address matches the
address space of your
network .
Make sure that the sub-
net mask matches the
address space of your
network .
Deactivate the firewall for
configuration.
WLAN Router 450
Troubleshooting
Error/Problem
It is not possible
to establish a
WLAN connection
to the device, the
WLAN LED ©
does not light up.
The speed of the
WLAN connection
is very slow.
Password forgot-
ten.
Possible cause
Wrong WLAN set-
tings
Unfavourable loca-
tion of the device.
Unfavourable
WLAN channel.
High-frequency
radiation interferes.
Remedy
Make sure that the
device and all clients in
the wireless network use
the same SSID, channel,
encryption method as
well as the same key.
Change the location and
alignment of the device.
Change the channel in
the event of interference.
Shield the devices that
emit high frequency inter-
ference or move them to
a different location.
Reset the device. See
section Restoring the
default settings.
D If you cannot resolve the problem with the steps described
above, please contact customer service.
WLAN Router 450
91
Appendix
Appendix
Support and contact information
For defective products:
In the event of product complaints, please contact your retailer or
Hama product support.
Internet/World Wide Web:
Product support, new drivers or product information can be obtained
at www.hama.com
Support hotline — Hama product support:
Tel. +49 (0) 9091 / 502-115
Fax +49 (0) 9091 / 502-272
Email: [email protected]
Notes on disposal
Do not dispose of the device as normal household waste. Pay
attention to the disposal instructions in the user manual ap-
pendix.
Notes on the EC Declaration of Conformity
Hama GmbH & Co. KG hereby declares that this device complies
with the fundamental requirements and other relevant provisions of
the 1999/5/EC directive. The Declaration of Conformity according to
the R&TTE Directive 99/5/EC can be found at www.hama.com
52 WLAN Router 450
Appendix
Operating restrictions
This device is approved for operation at home and in the office in all
EU countries (and other countries that comply with EU guidelines
1999/5/EC). There are no other limitations except the following:
If channel 36-64 (channels with frequencies 5150MHz - 5350MHZ) or
the 2.4GHz range in France are used, the device may only be used
in closed rooms.
WLAN Router 450 53
Appendix
94
Technical data
Router
Operating modes
Data rate
Frequency range
WLAN
Standard
Compatible with
Encryption
LAN
Network connection
Dimensions/weight
Dimensions
without antenna (L x W x H)
Weight (incl. antennas and
power supply)
Electrical ratings
Power supply
Ambient conditions
Operating temperature range
relative humidity (operation)
Storage temperature range
relative humidity (storage)
Access point, station (infrastruc-
ture), AP bridge point-to-point,
AP bridge point-to-multipoint, AP
bridge WDS, universal repeater
5 GHz up to 450 Mbps
2.4 GHz up to 300 Mbps
5 & 2.4 GHz
5 GHz: 802.11 n/a
(450 Mbps/54 Mbps)
2.4 GHz: 802.11n/g/b
(300 Mbps/54 Mbps/11 Mbps)
IEEE802.11n (5 GHz: 450 Mbps;
2.4 GHz: 300 Mbps)
IEEE802.11a (54 Mbps)
IEEE802.11g (54 Mbps)
IEEE802.11b (11 Mbps)
WiFi
WPA2, WPA, WEP (64/128 bit)
4-port- 10/100/1000 Mbps switch,
RJ 45
180 x 115 x 35 mm
approx. 403 g
12V=, 125A 0-0
0..40°C
20 ... 85 % (non-condensing)
-10...70 °C
0... 90 % (non-condensing)
WLAN Router 450
[4 1x4 129 [29 DA DA 124
|9 [34
(D) Hinweis zum Umweltschutz:
Ab dem Zeitpunkt der Umsetzung der europäischen Richtlinie 2002/96/EG und 2006/66/EG in nationales Recht gilt folgendes:
Elektrische und elektronische Altgeräte sowie Batterien dürfen nicht mit dem Hausmüll entsorgt werden. Der Verbraucher ist gesetzlich verpflichtet,
elektrische und elektronische Geräte sowie Batterien am Ende ihrer Lebensdauer an den dafür eingerichteten, öffentlichen Sammelstellen oder an
die Verkaufsstelle zurückzugeben. Einzelheiten dazu regelt das jeweilige Landesrecht. Das Symbol auf dem Produkt der Gebrauchsanleitung oder
der Verpackung weist auf diese Bestimmungen hin. Mit der Wiederverwertung, der stofflichen Verwertung oder anderer Formen der Verwertung von
Altgeräten/Batterien leisten Sie einen wichtigen Beitrag zum Schutz unserer Umwelt.
Note on environmental protection:
After the implementation of the European Directive 2002/96/EU and 2006/66/EU in the national legal system, the following applies:
Electric and electronic devices as well as batteries must not be disposed of with household waste. Consumers are obliged by law to return electrical
and electronic devices as well as batteries at the end of their service lives to the public collecting points set up for this purpose or point of sale.
Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates
that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices/Batteries, you are making an
important contribution to protecting our environment.
FP Remarques concernant la protection de l’environnement:
Conformément à la directive européenne 2002/96/CE et 2006/66/CE, et afin d'atteindre un certain nombre d'objectifs en matière de protection de
l‘environnement, les règles suivantes doivent être appliquées:
Les appareils électriques et électroniques ainsi que les batteries ne doivent pas être éliminés avec les déchets ménagers. Le pictogramme “picto”
présent sur le produit, son manuel d'utilisation ou son emballage indique que le produit est soumis à cette réglementation. Le consommateur doit
retourner le produit/la batterie usager aux points de collecte prévus à cet effet. Il peut aussi le remettre à un revendeur. En permettant enfin le
recyclage des produits ainsi que les batteries, le consommateur contribuera à la protection de notre environnement. C'est un acte écologique.
@ Nota sobre la protecciôn medioambiental:
Después de la puesta en marcha de la directiva Europea 2002/96/EU y 2006/66/EU en el sistema legislativo nacional, se aplicara lo siguiente:
Los aparatos eléctricos y electronicos, asi como las baterias, no se deben evacuar en la basura doméstica. El usuario esta legalmente obligado
a llevar los aparatos eléctricos y electrónicos, así como pilas y pilas recargables, al final de su vida útil a los puntos de recogida comunales 0 a
devolverlos al lugar donde los adquirió. Los detalles quedaran definidos por la ley de cada país. El símbolo en el producto, en las instrucciones de
uso o en el embalaje hace referencia a ello. Gracias al reciclaje, al reciclaje del material o a otras formas de reciclaje de aparatos/pilas usados,
contribuye Usted de forma importante a la protección de nuestro medio ambiente.
(ND Notitie aangaande de bescherming van het milieu:
Ten gevolge van de invoering van de Europese Richtlijn 2002/96/EU en 2006/66/EU in het nationaal juridisch system, is het volgende van toepassing:
Elektrische en elektronische apparatuur, zoals batterijen mag niet met het huisvuil weggegooid worden. Consumenten zijn wettelijk verplicht om
electrische en elctronische apparaten zoals batterijen op het einde van gebruik in te dienen bij openbare verzamelplaatsen speciaal opgezet voor
dit doeleinde of bij een verkooppunt. Verdere specificaties aangaande dit onderwerp zijn omschreven door de nationale wet van het betreffende
land. Dit symbool op het product, de gebruiksaanwijzing of de verpakking duidt erop dat het product onderworpen is aan deze richtlijnen. Door te
recycleren, hergebruiken van materialen of andere vormen van hergebruiken van oude toestellen/batterijen, levert u een grote bijdrage aan de
bescherming van het mileu.
(DD Informazioni per protezione ambientale:
Dopo I'implementazione della Direttiva Europea 2002/96/EU e 2006/66/EU nel sistema legale nazionale, ci sono le seguenti applicazioni:
Le apparecchiature elettriche ed elettroniche e le batterie non devono essere smaltite con i rifiuti domestici. | consumatori sono obbligati dalla
legge a restituire | dispositivi elettrici ed elettronici e le batterie alla fine della loro vita utile ai punti di raccolta pubblici preposti per questo scopo o
nei punti vendita. Dettagli di quanto riportato sono definiti dalle leggi nazionali di ogni stato. Questo simbolo sul prodotto, sul manuale d'istruzioni
o sullimballo indicano che questo prodotto é soggetto a queste regole. Riciclando, ri-utilizzando i materiali o utilizzando sotto altra forma ¡ vecchi
prodotti/le batterie, darete un importante contributo alla protezione dell' ambiente.
YTTÓdEIEN OXETIKÁ HE TINV TTPOCTACÍA TTEPIBÁMOVTOG:
ATTÔ Tn oTiypn Tou n Eupwraiki Odnyia 2002/96/EE kai 2006/66/EE evowpatwvetal oTO EOVIKÓ diKdIO IOYÚdUY TA E£NC:
O1 NEKTPIKÉG KaI Ol NAEKTPOVIKÉG CUOKEVÉG KaBwG Kar OI LITTATAPÍEC DEV ETTITPÉTTETAI VA TTETIOÛVTAI OTA OIKIOKÜ ATTOPPÍNVATA. OI KATAVANWTÉC
UTTOXPEOÚVTAI ATTÓ TOV VÓNO VA ETTIOTPÉMOUYV TIC NAEKTPIKÉG KaI NAEKTPOVIKÉC CUOKELÉG KABUIG KaI TIC UTTATAPIEG OTO TÉÂOG TNG CG TOUS OTA
Onpócia onpeía TTEPICUMoyfc TTOU ÉXoUV BniuIOUpynBEí y! dUTÓ TO OKOTTÓ Ñ OTA ONuEÍA TTWANONG. O1 AeTTONÉPeIEC PUBLiZovTal aTA OYETIKÁ
vopobecía. To cúuBoro TTávw OTO TTpoiôv, OTO EVYEIPÍDIO YPÑONGC À OTN OUOKEUAOÏA TTAPATTÉUTTEI GE QUTÉG TIC biATÓÁFEIG. Me Tv avakukAwon,
ETTAVAXPNOIUOTTOINON TWV VAIKWV pe ÓMEG HOPYÉC XPNOINOTIOÍNONG TTANIWV CUOKEUWYV / MiTATAPILV CUVEIOMÉPETE ONVAVTIKÁ OTIV TIPOOTACÍA
ToU TTEPIBÁMovTOG. 2TI Fepuavía ioyúduV avTioTOIXa Ol TTAPATTÓVW KavóveG ATTÓPPIUNC CÚNQWVA VE TOV KAVOVIOLIÓ VIA UTTATAPIEG KA
OUCOUPEUTÉG.
(S) Not om miljóskydd:
Efter implementeringen av EU direktiv 2002/96/EU och 2006/66/EU ¡ den nationella lagstiftningen, gáller fóljande:
Elektriska och elektroniska apparater samt batterier far inte kastas i hushallssoporna. Konsumenter &r skyldiga att áterlaámna elektriska och
elektroniska apparater samt batterier vid slutet av dess livslängd till, for detta ándamál, offentliga uppsamlingsplatser. Detaljer for detta definieras
via den nationella lagstiftningen i respektive land. Denna symbol pa produkten, instruktionsmanualen eller pa forpackningen indikerar att produkten
innefattas av denna bestámmelse. Genom átervinning och áteranvándning av material/batterier bidrar du till att skydda miljón och din omgivning.
(EIN) Ympäristönsuojelua koskeva ohje:
Siitä [ahtien, kun Euroopan unionin direktiivi 2002/96/EU ja 2006/66/EU otetaan kayttoon kansallisessa lainsaadanndssa, patevat seuraavat maaraykset:
Sahko- ja elektroniikkalaitteita ja paristoja ei saa havittaa talousjatteen mukana. Kuluttajalla on lain mukaan velvollisuus toimittaa sahko- ja elekt-
roniikkalaitteet niiden kayttdian paatyttya niille varattuihin julkisiin kerayspisteisiin tai palauttaa ne myyntipaikkaan. Tahan liittyvista yksityiskohdista
saadetaan kulloisenkin osavaltion laissa. Naista maarayksista mainitaan myôs tuotteen symbolissa, käyttôohjeessa tai pakkauksessa. Uudelleen-
kaytólla, materiaalien/paristoja uudelleenkäytôllà tai muilla vanhojen laitteiden uudelleenkäyttôtavoilla on tärkeä vaikutus yhteisen ympáristomme
suojelussa.
996350 Version 1.5
[54 154 113 1 13
LX 14 1 14
Wskazówki dotyczace ochrony srodowiska:
Od czasu wprowadzenia europejskiej dyrektywy 2002/96/EU i 2006/66/EU do prawa narodowego obowiazuja nastepujace ustalenia:
Urzadzeñ elektrycznych, elektronicznych oraz baterii jednorazowych nie nalezy wyrzucaé razem z codziennymi odpadami domowymi! Uzytkownik
Zobowiazany prawnie do odniesienia zepsutych, zniszczonych lub niepotrzebnych urzadzeñ elektrycznych i elektronicznych do punktu zbiórki
lub do sprzedawcy. Szczegótowe kwestie reguluja przepisy prawne danego kraju. Informuje o tym symbol przekreslonego kosza umieszczony na
opakowaniu. Segregujac odpady pomagasz chronié srodowisko!
HD Kornyezetvédelmi tudnivalók:
Az európai irányelvek 2002/96/EU és 2006/66/EU ajánlasa szerint, a megjelólt i¡dóponttól kezdve, minden EU-s tagállamban érvényesek a kóvetkezók:
Az elektromos és elektronikai készülékeket és az elemeket nem szabad a háztartási szemétbe dobni! A leselejtezett elektromos és elektronikus
készulékeket és elemeket, akkumulátorokat nem szabad a háztartási szemétbe dobni. Az elhasznált és múkódésképtelen elektromos és elektro-
nikus készülékek gyüjtésére tôrvényi elôiräs kôtelez mindenkit, ezért azokat el kell szállitani egy kijelólt gyújtó helyre vagy visszavinni a vásárlás
helyére. A termék csomagolásán feltúntetett szimbólum egyértelmú jelzést ad erre vonatkozóan a felhasználónak. A régi készúulékek begyújtése,
visszavaltasa vagy barmilyen formaban torténd djra hasznositasa k6zds hozzajarulas kornyezetiink védelméhez.
C2 Ochrana Zivotniho prostredi:
Evropska smérnice 2002/96/EG a 2006/66/EU ustanovujete nasledujici:
Elektricka a elektronicka zafizeni stejné jako baterie nepatfi do domovniho odpadu. Spotrebitel se zavazuje odevzdat véechna zañizeni a baterie po
uplynuti jejich Zivotnosti do prislusnych sbéren. Podrobnosti stanoví zákon priSlusné zemé. Symbol na produktu, navod k obsluze nebo baleni na
toto poukazuje. Recyklací a jinymi zpúsoby zuzitkování prispíváte k ochrané Zivotního prostredí.
GO Ochrana zivotného prostredia:
Európska smernica 2002/96/EU a 2006/66/EU stanovuje:
Elektrické a elektronické zariadenia, rovnako ako batérie sa nesmu vyhadzovat do domáceho odpadu. Spotrebitel je zo zákona povinny Zlikvidovat
elektrické a elektronické zariadenia, rovnako ako batérie na miesta k tomu urcené. Symbolizuje to obrázok v návode na pouzitie, alebo na baleni
vyrobku. Opatovnym zuZitkovanim alebo inou formou recyklacie starych zariadeni/batérii prispievate k ochrane Zivotného prostredia.
(СР) Nota em Proteccáo Ambiental:
Após a implementacáo da directiva comunitária 2002/96/EU e 2006/66/EU no sistema legal nacional, o seguinte aplica-se:
Os aparelhos eléctricos e electrónicos, bem como baterias, náo podem ser eliminados juntamente com o lixo doméstico. Consumidores estáo ob-
rigados por lei a colocar os aparelhos eléctricos e electrónicos, bem como baterias, sem uso em locais públicos específicos para este efeito ou no
ponto de venda. Os detalhes para este processo sáo definidos por lei pelos respectivos países. Este símbolo no produto, o manual de instruçôes
ou a embalagem indicam que o produto está sujeito a estes regulamentos. Reciclando, reutilizando os materiais dos seus velhos aparelhos/bateri-
as, esta a fazer uma enorme contribuiçäo para a protecçäo do ambiente.
Охрана окружающей среды:
С момента перехода национального законодательства на европейские нормативы 2002/96/Е0 и 2006/66/ЕО) действительно следующее:
Электрические и электронные приборы, а также батареи запрещается утилизировать с обычным мусором. Потребитель, согласно закону,
обязан утилизировать электрические и электронные приборы, а также батареи и аккумуляторы после их использования в специально
предназначенных для этого пунктах сбора, либо в пунктах продажи. Детальная регламентация этих требований осуществляется
соответствующим местным законодательством. Необходимость соблюдения данных предписаний обозначается особым значком на
изделии, инструкции по эксплуатации или упаковке. При переработке, повторном использовании материалов или при другой форме
утилизации бывших в употреблении приборов Вы помогаете охране окружающей среды. В соответствии с предписаниями по обращению
с батареями, в Германии вышеназванные нормативы действуют для утилизации батарей и аккумуляторов.
Cevre koruma uyarisi:
Avrupa Birligi Direktifi 2002/96/EU ve 2006/66/EU ulusal yasal uygulamalar icin de gecerli oldudu tarihten itibaren:
Elektrikli ve elektronik cihazlarla piller normal evsel cópe atilmamalidir. Tüketiciler için, artik çalismayan elektrikli ve elektronik cihazlari piller,
kamuya ait toplama yerlerine gotirme veya satin alindiklar yerlere geri verme yasal bir zorunluluktur. Bu konu ile ilgili ayrintilar ulusal yasalarla du-
zenlenmektedir. Ürün üzerinde, kullanma kilavuzunda veya ambalajda bulunan bu sembol tüketiciyi bu konuda uyarir. Eski cihazlarin geri kazanimi,
yapildiklart malzemelerin degerlendirilmesi veya diÿer dederlendirme sekilleri ile, gevre korumasina 6nemli bir katkida bulunursunuz. Yukarida adi
geçen atik toplama kurallar! Almanya'da piller ve aküler için de geçerlidir.
Instructiuni pentru protectia mediului inconjurätor:
Din momentul aplicärii directivelor europene 2002/96/UE în dreptul national sunt valabile urmätoarele:
Aparatele electrice si electronice nu pot fi salubrizate cu gunoiul menajer. Consumatorul este obigat conform legii sá predea aparatele electrice si
electronice la sfársitul duratei de utilizare la locurile de colectare publice sau inapoi de unde au fost cumpárate. Detaliile sunt reglementate de cátre
legislatia tárii respective. Simbolul de pe produs, in instructiunile de utilizare sau pe ambalaj indicá aceste reglementari. Prin reciclarea, revalorifica-
rea materialelor sau alte forme de valorificare a aparatelor scoase din uz aduceti o contributie importatá la protectia mediului nostru inconjurátor.
Anvisninger til beskyttelse af miljoet:
Fra og med indfgrelsen af EU-direktiverne 2002/96/EF og 2006/66/EF ¡ national ret geelder folgende:
Elektrisk og elektronisk udstyr samt batterier ma ikke bortskaffes sammen med almindeligt husholdningsaffald. Forbrugeren er lovmaessigt forpligtet
til at aflevere udtjent elektrisk og elektronisk udstyr samt batterier til dertil indrettede, offentlige indsamlingssteder eller til forhandleren. De паэгтеге
bestemmelser vedr. dette fastlægges af lovgivningen i det pageeldende land. Symbolet pa produktet, brugsvejledningen eller emballagen henviser til
disse bestemmelser. Ved genbrug, genvinding eller andre former for nyttiggerelse af udtjent udstyr/batterier giver du et vigtigt bidrag til beskyttelse
af miljget.
ND Informasjon om beskyttelse av miljoet:
Fra tidspunktet for omsetning av de europeiske direktivene 2002/96/EF og 2006/66/EF i nasjonal rett gjelder falgende:
Elektriske og elektroniske apparater og batterier ma ikke deponeres sammen med husholdningssgppelet. Forbrukeren er lovmessig forpliktet til
a levere elektriske og elektroniske apparater og batterier til de offentlige samlestedene eller tilbake til stedet hvor produktene ble kjgpt. Detaljer
angaende dette reguleres av hvert land. Symbolet pa produktet, bruksanvisningen eller emballasjen henviser om disse bestemmelsene. Med
resirkulering, gjenbruk av stoffer eller andre former av gjenbruk av gamle apparater/batterier bidrar du betydelig til á beskytte miljget vart.
Wenn Kanal 36-64 (Kanale der Frequenz 5150MHz
- 5350MHz) oder das 2,4GHz Band in Frankreich
verwendet wird, darf das Gerät nur in geschlossenen
Räumen verwendet werden.
Hiermit erklärt Hama GmbH & Co. KG, dass sich
dieses Gerät in Übereinstimmung mit den grundlegen-
den Anforderungen und den übrigen einschlägigen
Bestimmungen der Richtlinie 1999/5/EG befindet.
Die Konformitätserklärung nach der R&TTE Richtlinie
99/5/EG finden Sie unter www.hama.com
A 36-64 csatornak (az 5150MHz - 5350MHz frekven-
ciaju csatornak), vagy a 2,4GHz sav franciaorszagi
használata esetén a készuléket csak zárt térben
szabad használni.
A Hama GmbH 8 Co. KG ezúton kijelenti, hogy a jelen
készülék ósszhangban van az 1999/5/EK irányelv
alapvetó kovetelményeivel és az egyéb vonatkozó
rendelkezésekkel. A 99/5/EK R&TTE iranyelv szerinti
megfelelôségi nyilatkozatot a www.hama.com cimen
talalja meg.
When using channels 36-64 (frequency 5150 MHz —
5350 MHZ) or the 2.4 GHz band in France, the device
may only be operated in enclosed spaces.
Hama GmbH & Co. KG hereby declares that this de-
vice is in compliance with the basic requirements and
other relevant regulations of the 1999/5/EC guideline.
You will find the declaration of conformity with R&TTE
directive 99/5/EC on the internet at www.hama.com
Pokud se kanal 36-64 (kanaly frekvence 5150MHz
- 5350MHz) nebo pasmo 2,4GHz pouzivá ve
Francii, smi se pfistroj pouZivat pouze v uzavienych
prostorach.
Timto firma Hama GmbH & Co. KG potvrzuje, Ze
tento pfistroj odpovida zakladnim poZadavküm а
ostatním relevantním predpisúm smérnice 1999/5/ES.
Prohlaseni o shodé podle smérnice R&TTE 99/5/ES
najdete na internetovych strankach www.hama.com
L'appareil doit être utilisé à l'intérieur de bâtiments en
cas d'utilisation, en France, des canaux 36-64 (bande
de fréquences 5150 MHz - 5350 MHz) ou de la bande
de fréquence 2,4 GHz.
La société Hama GmbH & Co. KG certifie que cet
appareil est conforme aux exigences de base et aux
dispositions de la directive 1999/5/EC en vigueur.
Vous trouverez la déclaration de conformité à la
directive R&TTE 99/5/CE sur www.hama.com
Ak sa pouZziva kanal 36-64 (kanaly frekvencie
5150MHz - 5350MHz) alebo pâsmo 2,4GHz vo
Francúzsku, smie sa pristroj pouZivat iba v uzavretych
priestoroch.
Spoloënost Hama GmbH & Co. KG tymto prehlasuje,
Ze tento pristroj zodpoveda zakladnym poZiadavkam a
ostatnym relevantnym ustanoveniam Smernice 1999/5/
ES. Vyhlasenie o zhode podfa smernice R&TTE 99/5/
ES si môZete pozriet na adrese www.hama.com
Si se utiliza el canal 36-64 (canales de la frecuencia
5150MHz - 5350MHZ) o la banda de 2,4 GHz en
Francia, el aparato sólo se puede utilizar en recintos
cerrados.
Mediante la presente, Hama GmbH áCo. KG declara
que este aparato cumple con los requisitos básicos
y los demás reglamentos relevantes de la directiva
1999/5/CE. La declaración de conformidad según
la directiva R&TTE 99/5/CE la encontrará en www.
hama.com
Se forem utilizados os canais 36-64 (canais na gama
de frequéncias 5150 MHz - 5350 MHz) ou a banda
de 2,4 GHz na Franca, a utilizacáo do aparelho é
permitida apenas em recintos fechados.
A Hama GmbH 8: Co. KG declara, deste modo, que
este aparelho respeita as exigéncias básicas e restan-
tes requisitos relevantes da directiva 1999/5/CE. Pode
consultar a declaracáo de conformidade, segundo a
directiva RETTE 99/5/CE, em www.hama.com
Indien kanaal 36-64 (kanalen in de frequentieband
5150MHz - 5350MHz) of de 2,4GHz-band in Frankrijk
wordt gebruikt, dan mag het toestel uitsluitend binnen
gesloten ruimten worden gebruik.
Hiermee verklaart Hama GmbH & Co. KG, dat dit
apparaat voldoet aan de vereisten en de overige
relevante voorschriften van de richtlijn 1999/5/EG. De
verklaring van overeenstemming conform de R&TTE-
richtlijn 99/5/EG vindt u op internet onder www.hama.
com
Во Франции каналы 36-64 (диапазон 5150 - 5350
МГц) и канал 2,4 ГГц разрешается применять
только внутри помещений.
Компания Ната СтбН & Со. КС настоящим
подтверждает, что данное изделие полностью
соответствует основным требованиям, а также
предписаниям и положениям нормативов 1999/5/
ЕС. Заявление о соответствии товара нормам
R&TTE 99/5/EG cm. Ha Beby3ne www.hama.com
Se il canale 36-64 (canali della frequenza 5150MHz
- 5350MHz) o la banda 2,4GHz vengono utilizzati in
Francia, l'apparecchio su pud utilizzare esclusivamente
in locali chiusi.
Hama GmbH & Co. KG dichiara che questo apparec-
chio soddisfa i requisiti fondamentali ed & conforme
alle norme vigenti della direttiva 1999/5/CE. La dichia-
razione di conformita secondo la direttiva R&TTE 99/5/
CE é disponibile sul sito www.hama.com
Kanal 36-64 (5150MHz - 5350MHZ frekanslari
arasindaki kanallar) veya 2,4GHz Bant (Fransa)
kullanildiÿinda cihaz sadece kapali mekanlarda
kullanilmalidir.
Hama GmbH 8 Co. KG bu cihazin 1999/5/EC
Direktifi'nin ilgili talimatlarina ve bu direktif tarafindan
istenen kosullara uygunlugunu beyan eder. R&TTE
Direktifi 99/6/EC’ye gSre uygunluk beyani igin www.
hama.com adresine bakiniz.
Orav xpnaoiuotroieital 10 камали 36-64 (камал tng
сухубтптас 5150MHz - 5350MHZ) ñ n {wvn 2,4GHz
OTn Fahhia, n OUOKEUR ETTITPÉTTETAI VA XPNOINOTTOIEÏTAI
HÔVO O€ KAEIOTOÜG XWPOUG.
H etaipia Hama GmbH & Co. KG ônAwvel Twç n
OUOKEUF UT EKTTANPUVEI TIC BACIKÉG ATTAITÁCEIC KAI
TIC AOITTEG OYETIKÉG DiATÓEEIC TIC OBNVÍAC 1999/5/EK
Tn dfAwon ouppôpewong oûuEuva pe Tnv oônyia
R&TTE 99/5/EK Ba Tn Bpeite oTn dievOuvon www.
hama.com
Dacä canalul 36-64 (canal cu frecvenla 5150MHz
- 5350MHz) sau banda de 2,4 GHz se foloseïte in
Frania, aparatul are voie sa se foloseasca numai in
incaperi inchise.
Hama GmbH & Co. KG, declara prin prezenta ca acest
aparat este in conformitate cu cerintele esentiale si
celelalte hotárári relevante ale Directivei 1999/5/EC.
Declaratia de conformitate conform Directivei R&TTE
99/5/EC o gasiti in Internet la www.hama.com
Nar kanal 36-64 (kanaler for frekvensen 5150MHz -
5350MHz) eller 2,4GHz bandet anvands i Frankrike far
apparaten bara anvandas inomhus.
Hama GmbH & Co. KG forsakrar harmed att den har
apparaten overensstammer med de grundlaggande
kraven och ôvriga relevanta bestammelser i direktivet
1999/5/EG. Fôrsäkran om ôverensstämmelse enligt
R&TTE-direktivet 99/5/EG hittar du pa www.hama.com
Hvis kanal 36-64 (kanaler pa frekvensen 5150 MHz —
5350 MHz) eller 2,4 GHz-bandet anvendes i Frankrig,
ma apparatet kun anvendes i lukkede rum.
Hama GmbH & Co. KG erklærer hermed, at dette
apparat er i overensstemmelse med de grundlæggen-
de krav og de gvrige, relevante bestemmelser i direktiv
1999/5/EF, Overensstemmelseserkleeringen ¡ henhold
til direktivet om radio og teleterminaludstyr 99/5/EF
kan du finde pá www.hama.com
Käytettäessä kanavia 36-64 (kanavia taajuusalueella
5150 MHz - 5350 MHz) tai Ranskan 2,4 GHz:n taajuus-
kaistaa laitetta saa kayttaa vain suljetuissa tiloissa.
Hama GmbH & Co. KG vakuuttaa taten, etta tama
laite on direktiivin 1999/5/EY perusvaatimusten ja
muiden oleellisten saáannosten mukainen. Radio- ja
telepaatelaitteita koskevan direktiivin 99/5/EY mukai-
nen vaatimustenmukaisuusvakuutus lOytyy osoitteesta
www.hama.com
Hvis kanal 36-64 (kanaler pa frekvens 5150 MHz -
5350 MHz) eller 2,4 GHz-bandet brukes i Frankrike,
skal enheten kun benyttes i lukkede rom.
Med dette erklærer Hama GmbH & Co. KG at dette
apparatet er i overensstemmelse med grunnleggende
krav og relevante bestemmelser i direktiv 1999/5/EF.
Du finner samsvarserklæringen i henhold til R&TTE-
direktiv 99/5/EF under www.hama.com
Jezeli kanat 36-64 (kanaty czestotliwosci 5150 MHz — 5350 MHz) lub pasmo 2,4 GHz uzywane beda we Francii,
urzadzenie wolno stosowac tylko w zamknietych pomieszczeniach.
Hama GmbH & Co. KG o$wiadcza niniejszym, ze urzadzenie to spetnia podstawowe wymagania i pozostate wlasciwe
postanowienia dyrektywy
1999/5/WE. Deklaracja zgodnosci wg dyrektywy 99/5WE dotyczacej urzadzen radiowych i telekomunikacyjnych dostepna
jest na stronie www.hama.com
®
Hama GmbH & Co KG
D-86651 Monheim/Germany
www.hama.com
All listed brands are trademarks of the corresponding companies.
Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.
Ceo
00053179/07.12