Hirschmann BAT-C Industrial Wireless LAN Client Reference Manual

PDF

Document

CLI-Reference Industrial Wireless LAN Client BAT-C

BAT-C Release 03 05/2016 Technical Support https://hirschmann-support.belden.eu.com

The naming of copyrighted trademarks in this manual, even when not specially indicated, should not be taken to mean that these names may be considered as free in the sense of the trademark and trade name protection law and hence that they may be freely used by anyone. © 2016 Hirschmann Automation and Control GmbH Manuals and software are protected by copyright. All rights reserved. The copying, reproduction, translation, conversion into any electronic medium or machine scannable form is not permitted, either in whole or in part. An exception is the preparation of a backup copy of the software for your own use. For devices with embedded software, the end-user license agreement on the enclosed CD applies. The performance features described here are binding only if they have been expressly agreed when the contract was made. This document was produced by Hirschmann Automation and Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right to change the contents of this document without prior notice. Hirschmann can give no guarantee in respect of the correctness or accuracy of the information in this document. Hirschmann can accept no responsibility for damages, resulting from the use of the network components or the associated operating software. In addition, we refer to the conditions of use specified in the license contract. You can get the latest version of this manual on the Internet at the Hirschmann product site (www.hirschmann.com). Printed in Germany Hirschmann Automation and Control GmbH Stuttgarter Str. 45-51 72654 Neckartenzlingen Germany Tel.: +49 1805 141538 2 BAT-C Release 03 05/2016

ABOUT THIS MANUAL

BAT-C Release 03 05/2016

6

26

9

9 9

10 10

11 11

7

AT*AGRTE Data Rate and Link Adaptation

4 NETWORK LAYER COMMANDS

AT*ANDHCP DCHP Activation

AT*ANHN Hostname

AT*ANDNS DNS Settings

5 DATA MODE COMMANDS

AT*ADC Connect AT*ADCP Connect to BSSID

AT*ADCPN Connect to name (SSID)

AT*ADCC Close Connection

AT*ADRDRP Read Default Remote Peer

AT*ADWDRP Write Remote Peer Information

AT*ADRL Roaming List

AT*ADRRL Read Roaming List

AT*ADWRL Write Roaming List

AT*ADLNK Read WLAN link status

6 INFORMATIONAL COMMANDS

6.1

6.2

AT*AILBA Read Local MAC Address

AT*AILVI Local version

7 MISCELLANEOUS COMMANDS

AT*AMLO Log Out AT*AMGD General Data

AT*AMMP Max Output Power

AT*AMWS Watchdog Settings

AT*AMESS Event and Status Subscriber

AT*AMSMF SMART Mode (Button) functionality

AT*AMSMFL SMART Mode Function List

AT*AMSSC SNMP Sys Contact

AT*AMSSL SNMP Sys Location

AT*AMSSS SNMP Sys Services AT*AMSBN SNMP Basic Name

AT*AMSBD SNMP Basic Descriptor

56

68 68

58

59 59

47

47 47

43

BAT-C Release 03 05/2016

AT*AMSSD SNMP Sys Description

AT*AMSWC SNMP Write Community (Private Community) AT*AMSEID SNMP Enterprise ID

AT*AMTL TCP Listener

AT*AMUR UDP Receiver

AT*AMHL HTTP Listener

AT*AMSR SNMP Receiver

AT*AMLCR Link Config Receiver

AT*ACEW Configure Mode

AT*AMEO Set External Digital Output AT*AMSTAT Read Current Status

AT*AMWID Wireless interface disable

AT*AMPSM Profisafe Mode

8 EVENTS

*ADCPO Connection Up *ADCCO Connection Closed

*AMDST Digital Signal Transition *AMRSS Low RSSI Warning

A FURTHER SUPPORT

71 71

78 78

83

83 83

84 84

85

BAT-C Release 03 05/2016 5

About this manual

The following manuals are available as PDF files on the CD-ROM supplied: ► User Manual Configuration and Administration ► Reference Manual ► User Manual Installation ■

1 AT command syntax

1.1 Command Line Format

Each command line sent from the DTE (data terminal equipment) to the DCE (data communications equipment) consists of a prefix, body, and terminator. As prefix for the BAT C AT commands, only "AT" (ASCII 65, 84) and "at" (ASCII 97, 116) can be used. There is no distinction between upper and lower case characters. The body is a string of characters in the range ASCII 032-255. Control characters other than (carriage return; ASCII 13) and (backspace; ASCII 8) in a command line are ignored. The terminator is . Commands denoted with a "*" character are extended AT commands, i.e. BAT-C specific AT commands. The command line is limited to one command at a time. Terminate each command with a before sending a new command. The limit of a command line is 300 characters. A command can either be: ► ► ► Read commands without parameters: AT? Write commands without parameters: AT Read and write commands with parameters: AT=, , ... The device sends responses back to the host and can be any of the following: ► ► ► ► This response indicates a successful execution of the write command: OK A read command will precede the OK response with the read parameters. The form is :,,..., String results will have "" around them. Successful intermediate/final message with parameters follows an OK message in some commands. In these cases, the OK message works as a confirmation message only. :, parameter2>, ... This response indicates an unsuccessful execution of the write command: ERROR

1.2 Limitations

When a AT command is issued with the store parameter set to 1, the previous values will be stored as well, regardless of whether the previous commands where issued with the store parameter set to 1 or not.

1.3 Data Types

The definition of each command specifies the data types used for values associated with the command. There are four different data types: ► ► ► ► ► String Octet String Integer IP_Addr MAC_Addr BAT-C Release 03 05/2016 7

The follow paragraph describes the Data Type listed above: ►

String

A string consists of a sequence of displayable characters from the ISO 8859-1 (8-bit ASCII) character set, except for characters "\", """ and characters below 32 (space). A string constant shall be delimited by two double-quote (""") characters, e.g. "Donald Duck". Use the "\" character as an escape character to insert raw bytes in a string. If the double-quote character (""") is to be used within a string, e.g. "My friend "Bono" is a singer", they have to be represented as "\22". If the back-slash character ("\") is to be used within a string constant, it has to be represented as "\5C". An empty string is represented by two adjacent delimiters, "".

►

Octet String

An octet string shall consist of an even number of hexadecimal values. Valid values are 0-9, 'a'-'f' and 'A'-'F'. ►

Integer

An integer value consists of a sequence of characters all in the range {0..9}. An integer can also be represented by as hexadecimal string, e.g. 15 can be written as "0x0000000F", excluding the double-quote characters. ►

IP_Addr

A valid IP address consists of four integer values separated by dots. Valid range of each integer value is {0..255}. An example IP address is "192.168.0.1", excluding the double quote characters. ►

MAC_Addr

A MAC consists of a sequence of six values, expressed in two-digit hexadecimal, in sequence. Group the hexadecimal values together without delimiters. An example MAC address is "00A0F7101C08", excluding the double-quote characters. The MAC address is an Octet String with a fixed length of 12. 8 BAT-C Release 03 05/2016

2 Standard AT Commands

2.1 AT Attention Command

Syntax Description

AT This is an ATtention command determining the presence of a DCE, i.e. the Ethernet Port Adapter.

Responses

Description

This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command.

**2.2 AT* List Available Commands**

Syntax Description

AT*

Responses

Lists the supported AT commands

Description

... OK The device sends a response to the host for every successful supported command, followed by an “OK”.. OK ERROR This response indicates a execution of the write command. successful This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 9

2.3 AT&F Restore to Factory Settings

Syntax Description

AT&F This command instructs the device to set all parameters to their defaults as specified by the manufacturer (Factory).

Responses Description

OK This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command.

2.4 AT&F0 Restore to Factory Settings

Syntax Description

AT&F0 See the description of the AT&F Restore to Factory Settings command.

Responses Description

OK This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command. 10 BAT-C Release 03 05/2016

2.5 ATE Echo Off

Syntax

ATE

Description

Use this command to configure the Ethernet Port Adapter to Echo the incoming characters.

Responses

Description

This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command.

2.6 ATE Echo On/Off

Syntax

ATE

Description

Use this command to configure the Ethernet Port Adapter to Echo the incoming characters. Use this command to read the current Echo setting. ATE?

Input and Response Parameters

echo_on

Type Description

integer 0 = The echo characters function is off during command state and online command state. 1 = Unit echoes characters during command state and online command state. BAT-C Release 03 05/2016 11

Responses

echo_on OK OK

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command.

2.7 ATQ Result Codes On/Off

Syntax Description

ATQ Configuring this parameter determines whether or not the unit transmits result codes to the DTE, (Quit). When suppressing result codes, no transmission of any portion of any intermediate, final, or unsolicited result code, i.e. header, result text, line terminator, or trailer, occurs. The value of this parameter has no affects on information text transmitted in response to commands. ATQ? Use this command to read the current result code setting, (Quit).

Input and Response Parameters

result_off

Type Description

integer 0 = Unit transmits result codes. 1 = Result codes are suppressed. 12 BAT-C Release 03 05/2016

Responses

result_off OK OK

Description

The device displays the current parameter setting followed by ”OK“, after entering a successful read command.. This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command.

2.8 ATS2 Escape Character

Syntax Description

ATS2= This command is issued to change the escape character to “esc_char”. Use this command to read the current escape character. ATS2?

Input and Response Parameters

esc_char

Type Description

integer “esc_char” is the ASCII value of the new escape character, i.e. 47 equals '/'. The default character is '/'.

Note:

The escape sequence will be "///". Therefore, enter the character three times.

Responses

>LF>esc_char OK

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. OK This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 13

2.9 ATS3 Command Line Termination Character

Syntax Description

ATS3= Use this command to write command line termination character. This setting changes the decimal value of the character recognized by the DCE from the DTE to terminate an incoming command line. The DCE also generates this as part of the header, trailer, and terminator for result codes and information text along with the S4 parameter Use the previous value of S3 to determine the command line termination character for entering the command line containing the S3 setting command. However, the result code issued uses the value of S3 as set during the processing of the command line. For example, if S3 was previously set to 13 and you enter the command line "ATS3=30". You use the CR, character (13), to terminate the command line but the result code issued will use the character with the ordinal value 30 in place of the CR. ATS3? Use this command to read the current command line termination character.

Input and Response Parameters Type Description

line_term

Responses

integer 0...127 (13, CR is default) line_term OK ERROR

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. OK This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 14 BAT-C Release 03 05/2016

2.10 ATS4 Response Formatting Character

Syntax Description

ATS4= Use this command to write response-formatting character. This setting changes the decimal value of the character generated by the DCE as part of the header, trailer, and terminator for result codes and information text, along with the S3 parameter. If you change the value of S4 in a command line, the result code issued in response to that command line will use the new value of S4. ATS4? Use this command to read the current response-formatting character.

Input and Response Parameters Type Description

term

Responses

integer 0...127 (10, LF is default)

Description

term OK ERROR The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 15

2.11 ATS5 Response Formatting Character

Syntax Description

ATS5= Use this command to write backspace character. This setting changes the decimal value of the character recognized by the DCE as a request to delete from the command line the immediately preceding character. Use this command to read the current backspace character. ATS5?

Input and Response Parameters

backspace

Responses

backspace OK OK

Type Description

integer 0...127 (8, BS is default)

Description

2.12 ATS General Settings S Register Manipulation

Syntax Description

ATS= Use this command to write to a general settings S register. ATS?

Input and Response Parameters

1100 Use this command to read from a general settings S register.

Type Description

register value integer Any of the registers described below. integer -2147483648...2147483647 or 0x00000000...0xFFFFFFFF. Listed below are valid values for each register.

Responses

value OK OK

Description

Register Roaming registers Description

RSSI thresholds Use this by the smart LEDs deciding how to indicate the current RSSI. Default value is 0xC9BFB5AB, giving the following limits: >85 dBm -> 1 LED >75 dBm -> 2 LEDs >65 dBm -> 3 LEDs >55 dBm -> 4 LEDs BAT-C Release 03 05/2016 17

Responses

1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1119

Miscellaneous

1200 1201 1202 1203 18

Description

Reserved Reserved Reserved Reserved Roaming scheme 0: Connect to name, see connect to name scheme (default) 1: Connect to next. This will simply connect to the next device configured with AT*ADWRL Write Roaming List 2-31: Reserved Reserved Reserved Reserved Reserved Reserved Roaming RSSI diff threshold (default 10) When the difference between the connected AP RSSI and the RSSI from the best AP from background scan exceeds this threshold a roaming handover is done. Reserved Use this register to configure the time in seconds before the LEDs turn off. Entering “0” will disable the feature. Reserved Reserved Disable Link configuration if broadcast BAT-C Release 03 05/2016

1208 1209 1210 1211 1212 1213 1214

Responses

1204 1205 1206 1207 BAT-C Release 03 05/2016

Description

Reserved Reserved Reserved Event Subscriber Protocol The device sends events according to this value. 0: disable (default) 1: Messages sent by AT over TCP 2: Messages sent by AT over Layer-2, mac_address must be specified using AT*AMESS 3: Syslog, destination IP address must be specified using AT*AMESS 4 - 255: reserved Event Subscriber Port / Ethernet type Wireless Interface Disable 0 = Enable Wireless Interface (default) 1 = Disable Bridge Cache Timeout Time in seconds before MAC address cache table in the bridge throws away an entry. Bit mask representing SMART LED Mode when finishing smart mode Bit 0: RSSI Bit 1: RESERVED Bit 3-31: RESERVED Smart LED Update timeout in seconds Activate User Management 0: disable 1: enable Smart mode button push functionality 0: Disconnect/connect 1: Toggle ALL LEDs 2: Reset 19

1219 1220

Profinet

1900 1901 20

Responses

1215 1216 1217 1218

Description

Smart mode button hold functionality 0: Disconnect/connect 1: Toggle ALL LEDs 2: Reset External trigger push functionality 0: Disconnect/connect 1: Toggle ALL LEDs 2: Reset External trigger hold functionality 0: Disconnect/connect 1: Toggle ALL LEDs 2: Reset Write diagnose mode bitmask. Default value is 0x00000001. This function sends the following events when the bit is set: Bit 0: *ADCPO - Connection up *ADCCO - Connection down *AMDST - Digital signal transition *AMRSS - RSSI value below -70dBm Bit 1: *AGRSS - RSSI periodically sent with interval set by ATS register 1219 *AGCH - Used WLAN channel, sent upon connection setup Bit 2: *AGSCAN - Background scan result RSSI poll interval in milliseconds Default value is 1000 ms. Maximum time to wait for first push on SMART button Default value is 5000 ms. Reserved Reserved BAT-C Release 03 05/2016

3005 3006 3007 3008 3009 3010 3001 3002 3003 3004

Responses

1902 1903 1904

WLAN

3000 BAT-C Release 03 05/2016

Description

Profinet prioritization: 0: Disable (default) 1: Enable Reserved Ethernet type to prioritize, default 0x8892 WLAN preamble 0 = Long preamble 1 = Short preamble (default) Reserved WLAN minimum scan time in milliseconds on each channel 0...65535 (default 50) WLAN maximum scan time in milliseconds on each channel 0...65535 (default 200) WLAN scan type 0 = Active scan (default) 1 = Passive scan Reserved Averaging depth for the RSSI trigger 1...16 (default 4, 1 means no depth) WLAN lower lost beacon value to trigger a rescan. The maximum number of lost beacons before a rescan happens. 1...32 (default 30) Averaging depth for the lost beacon trigger 1...32 (default 32) Reserved Reserved 21

Responses

3011 3012 3013 3014 3015 3016 3017 3018 3019 22

Description

Beacon Period of the BSS Descriptor of the ESS to Join or Start a network in IBSS. Value in milliseconds 100 (default 100) Use this register to configure the time limit, in units of beacon intervals, after which termination of the Join procedure occurs. 1...100 (default 10) Reserved Max power (use AT*AMMP) Reserved Data Rate (use AT*AGRTE) Link Adaption (use AT*AGRTE) 0: Disable 1: Enable Power save 0: Disable 1: Enable Regulatory domain 1: World Domain (default) (1...11) 2.4GHz 2: FCC (1...11) 2.4GHz 3: ETSI (1...13) 2.4GHz 4: TELEC (1...14) 2.4GHz 10: U-NII-1 (36, 40, 44, 48) 5GHz 20: U-NII-2 (52, 56, 60, 64) 5 GHz 40: U-NII-2 extended (100, 104, 108, 116, 120, 124, 128, 132, 136, 140 ) 5 GHz 80: U-NII-3 Upper (149, 153, 157, 161) 5 GHz The regulatory domain values can be added if multiple options are required. For example, 21 (20 + 1) represents option 1 and option 20 and signifies World Domain and U-NII-1. Note: After changing the regulatory domain, verify that the channel list is updated according to your preferences as well. (AT*AGCL) BAT-C Release 03 05/2016

Responses

3020 3021 3022 3023 3024 3025 3026 3027

Description

DTIM Enable 0: Disable 1: Enable (default) QoS Enable 0: Disable 1: Enable (default) Reserved Reserved Reserved Reserved Reserved Background scanning idle timeout (default 1000 ms) When there has been no data activity for the last 'idle timeout' ms, the background scan starts. 3028 3029 4000 BAT-C Release 03 05/2016 Background scanning interval Time between background scans(default 5000 ms) Background scanning scheme Configure when to initiate background scanning with this register. A prerequisite for this is that the RSSI level is below Trigger Scan RSSI (ATS4012). 0: Always in intervals of ATS3028 ms 1: When idle, the idle time is checked every ATS3028 ms. Reserved, do not modify 23

4004 4005 4006 4007 4008 4009 4010

Responses

4001 4002 4003 4011 24

Description

Reserved, do not modify. Reserved, do not modify. WPA key input mode Controls how the WPA key is parsed and interpreted. 0 = Auto (default) 1 = ASCII 2 = Hexadecimal Auto mode will try to determine if it the input is an ASCII key or a HEX key by looking at the contents. Reserved Reserved Reserved Reserved, do not modify Ad-hoc timeout Time before a single unit in an ad-hoc network tries a rescan to find an existing network. Value in milliseconds 0 = disabled 0...2147483647 (default 6000) Delayed association This value sets the time to wait before initiating an association attempt. Value in milliseconds 0 = no delay 0...2147483647 (default 0) LLDP send interval The module sends, per default, information in LLDP frames with its current setup and those of its peers. Another use for this parameter is to stay alive on access points that do not properly wake the module before a disassociation. Value in seconds 0 = Do not send. 0...2147483 (default 60) Reserved BAT-C Release 03 05/2016

5001 5002 5003

Responses

4012 4013 4014

Networking

5000

Description

Trigger Scan RSSI Defines at what RSSI level to initiate a background scan to search for a better connection. Normally when the Slave is lost, the Master assumes this task. The Master searches for a better connection when RSSI exceeds this value. LLDP hold multiplier This value multiplied with LLDP interval equals the total time an LLDP update is valid. 1...10 (default 4) Enable/disable adaptive RSSI threshold. 0 = Disable (default) 1 = Enable Turn on/off TCP keep-alive packets It is important to understand that sending frequent keep-alive packets usually isn't a good solution to detect dropped connections. Perform dead links detection on a higher level, i.e. in the user application protocol. There is a lot of information available on the subject on the web. 0 = TCP keep-alive packets turned off (default)1 = TCP keep alive packets turned on This is the time in milliseconds for a TCP connection to be idle before sending a keep-alive packet. 0...2147483647 (default 7200000 = 2 hours) This is the time in milliseconds between keep-alive packets after losing a keep-alive packet. 0...2147483647 (default 75000 = 75 seconds) This is the number of lost keep-alive packets to wait before resetting a TCP connection. 1...255 (default 9) BAT-C Release 03 05/2016 25

3 Link Layer Commands

**3.1 AT*AGAM Authentication Mode**

Syntax Description

AT*AGAM=, Use this command to write Authentication Mode. AT*AGAM? Use this command to read the current Authentication Mode.

Input and Response Parameters Type Value

amode store_in_startup_database Integer 0 = Open (default) 1 = Shared secret 2 = WPA/WPA2 PSK 3 = LEAP 4 = PEAP 5 = Reserved Integer 0: The setting will be valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*AGAM: OK OK ERROR

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 26 BAT-C Release 03 05/2016

**3.2 AT*AGEM Encryption Mode**

Syntax

AT*AGEM?

Description

AT*AGEM=, Use this command to write Encryption Mode Use this command to read the current Encryption Mode.

Input and Response Parameters Type Value

emode Integer 0 = None (default) 1 = WEP64 2 = WEP128 3 = TKIP 4 = AES/CCMP store_in_startup_database Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses Description

*AGEM: OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. OK This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 27

**3.3 AT*AGSM Security Mode**

Syntax Description

AT*AGSM=, Use this command to write Security Mode. Security Mode is a shortcut for setting a combination of the authentication and encryption modes. Sending a "AT*AGSM=3" command is therefore the equivalent of sending the commands: "AT*AGAM=2" and "AT*AGEM=3". If you send a "AT*AGSM?" command, the DCE will return 255 if the current settings do not match the predefined values. AT*AGSM? Use this command to read the current security mode.

Input and Response Parameters Type Value

smode store_in_startup_database Integer 0 = No security (default) (AM=0,EM=0) 1 = Shared-WEP64 (AM=1,EM=1) 2 = Shared-WEP128 (AM=1,EM=2) 3 = WPA-PSK-TKIP (AM=2,EM=3) 4 = WPA2-PSK-AES/CCMP (AM=2,EM=4) 5 = LEAP-WPA2 (AM=3,EM=4) 6 = LEAP-WEP128 (AM=3,EM=2) Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*AGSM: OK OK ERROR

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 28 BAT-C Release 03 05/2016

**3.4 AT*AGOM Operational Mode**

Syntax Description

AT*AGOM=, Use this command to write the Operational Mode, i.e. if the device is operating in an Ad-Hoc environment or as a predetermined infrastructure with access points. AT*AGOM? Use this command to read the current Operational Mode.

Input and Response Parameters Type Value

omode store_in_startup_database Integer 1 = Managed (infrastructure) (default) 2 = Ad-Hoc Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*AGOM: OK OK ERROR

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 29

**3.5 AT*AGFP Encryption/Authentication Key**

Syntax Description

AT*AGFP=,< CR> Use this command to write the encryption/authentication key for index 1. This command is a shortcut for AT*AGFPWI=1,,.

Input Parameters Type Value

key store_in_startup_database String Use any string value for this setting. Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

Description

This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command. 30 BAT-C Release 03 05/2016

**3.6 AT*AGFPWI Write Encryption/Authentication Key (with Index)**

Syntax Description

AT*AGFPWI=, ,

Input Parameters

Use this command to write the encryption/authentication key.

Type Value

keyindex Integer The valid integers are 1...4. key store_in_startup_database String Use any string value for this setting. Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

Description

This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 31

**3.7 AT*AGAFP Active Encryption/Authentication Key**

Syntax Description

AT*AGAFP=, Use this command to write the active encryption/authentication key. AT*AGAFP? Use this command to read the current active encryption/authentication key.

Input and Response Parameters Type Value

keyindex store_in_startup_database Integer Valid integers for this function are 1...4 (1 default). Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*AGAFP: OK OK ERROR

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 32 BAT-C Release 03 05/2016

**3.8 AT*AGUN Username**

Syntax Description

AT*AGUN=, Use this command to write the UserName. AT*AGUN? Use this command to read the current the UserName.

Input and Response Parameters Type Value

username store_in_startup_database String Use this name for identification on authentication servers. See AT*AGAM Authentication Mode. Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*AGUN: OK OK ERROR

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 33

**3.9 AT*AGDN Domain name**

Syntax Description

AT*AGDN=, Use this command to write the Domain Name. AT*AGDN? Use this command to read the current the Domain Name.

Input and Response Parameters Type Value

domain store_in_startup_database String This is the domain to use with authentication servers. See AT*AGAM Authentication Mode. Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*AGDN: OK OK ERROR

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 34 BAT-C Release 03 05/2016

**3.10 AT*AGCFP Certificate Fingerprint**

Syntax Description

AT*AGCFP=, Use this command to write the Certificate Finger Print. AT*AGCFP? Use this command to read the current Certificate Finger Print.

Input and Response Parameters Type Value

fingerprint store_in_startup_database Octet String This is a 20 bytes octet string representing the fingerprint. (quotes (") shall not be used) Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses Description

*AGCFP: OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. OK ERROR This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 35

**3.11 AT*AGSSID Network Name (SSID)**

Syntax Description

AT*AGSSID=, AT*AGSSID? Use this command to write the Network Name (SSID) of the access point. Use this command to read the current Network Name (SSID) of the access point.

Input and Response Parameters Type Value

ssid store_in_startup_database String Use any string value, max length 32 bytes. Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*AGSSID: OK OK

Description

**3.12 AT*AGRSS RSSI Value**

Syntax Description

AT*AGRSS? Use this command to read the current RSSI value of the connection. If the module is not connected it returns an ERROR.

Response Parameter Type Value

rssi Integer This is the RSSI value. -128...10 where value is dBm value Use this command after the device establishes a connection, otherwise, the response to this read command is an error message.

Responses

*AGRSS: OK

Description

This response indicates a successful execution of the write command. ERROR This response indicates unsuccessful execution of the write command. BAT-C Release 03 05/2016 37

**3.13 AT*AGCH Channel Number**

Syntax

AT*AGCH?

Description

AT*AGCH=, Use this command to write the Channel number to use. Use this command to read the current CHannel number in use.

Input and Response Parameters Type Value

ch_no Integer 0 = Auto (default), select from defined channel list. > 0 = Channel to use. Available channels depending on regulatory domain setting. store_in_startup_database Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*AGCH: OK OK

Description

**3.14 AT*AGCL Channel List**

Syntax

AT*AGCL=,, …,, AT*AGCH?

Description

Use this command to write the channel number to use. Use this command to read the current channel number in use.

Input and Response Parameters

ch#

Type Value

Integer Write the channel list to use. This list also specifies the scan order. The number of channels to specify is dependent on the regulatory domain set. See command AMRD for details about regulatory domains and below for channel list lengths. If you don´t want to use all positions, pad list with zeros. Channel list length for the regulatory domains: World = 11 FCC = 11 ETSI = 13 U-NII band 1 = 4 U-NII band 2 = 4 U-NII band 2 extended = 11 U-NII band 3 Upper = 4 Example 1: If regulatory domain is set to World + U-NII band 1 + 2, then the number of channels to specify is 11 + 4 + 4 = 19. AT*AGCL:6,1,11,2,7,4,9,3,8,5,10,36,40,44,48,52,56,60,64,1 Example 2: To use only channel 1,6 and 11 in regulatory domain ‘World’. AT*AGCL=1,6,11,0,0,0,0,0,0,0,0,0,0,0,1 store_in_startup_database Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database. BAT-C Release 03 05/2016 39

Responses Description

*AGCL:,,..., OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. OK ERROR This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command.

**3.15 AT*AGSCAN**

Syntax

AT*AGSCAN? AT*AGSCAN=,

Input and Response Parameters

bssid op_mode

Type

ssid channel rssi encryption

Description

Use this command to SCAN for available networks. The command will return 0...48 networks in the immediate surroundings, then return OK. Use this command to SCAN the available networks with specific a SSID on a specified channel.

Value

MAC_Addr MAC address of the access point Integer 1 = Infrastructure 2 = Ad-hoc String Integer Integer SSID name of network Channel the network uses Signal strength value for the network Integer 0 = No encryption 1 = WEP 2 = WPA 3 = WPA2/RSN 40 BAT-C Release 03 05/2016

Input and Response Parameters

information_element

Type

String

Value

This is a Hexadecimal string with the information element for WPA and RSN networks. The string is unavailable for WEP networks or networks without encryption.

Responses

*AGSCAN: , , , , , , OK ERROR

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates an unsuccessful execution of the write command.

**3.16 AT*AGRTE Data Rate and Link Adaptation**

Syntax Description

AT*AGRTE=, , AT*AGRTE? Use this command to write the data Rate and link adaptation settings. Use this command to read the current data Rate and link adaptation settings. BAT-C Release 03 05/2016 41

Input and Response Parameters

data_rate link_adaptation store_in_startup_database

Responses

*AGRTE:, OK OK ERROR

Type Value

Integer Integer Integer 1 = 1Mbit (only 2.4GHz) 2 = 2Mbit (only 2.4GHz) 3 = 5.5Mbit (only 2.4GHz) 4 = 6Mbit 5 = 9Mbit 6 = 11Mbit (only 2.4GHz) 7 = 12Mbit 8 = 18Mbit 9 = 24Mbit (default) 10 = 36Mbit 11 = 48Mbit 12 = 54Mbit 13 = 6.5Mbit 14 = 13Mbit 15 = 19.5Mbit 16 = 26Mbit 17 = 39Mbit 18 = 52Mbit 19 = 58.5Mbit 0 = Link adaptation off. The device uses the configured data_rate. 1 = Link adaptation on. The data_rate of the device adjusts automatically depending on the operation environment. 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 42 BAT-C Release 03 05/2016

4 Network Layer Commands

**4.1 AT*ANIP IP Settings**

Syntax Description

AT*ANIP=, , , AT*ANIP? Use this command to write the system information, i.e. IP address, netmask, and gateway IP. The device requires a restart to activate the new configuration. The “AT*ANIP?” Command returns the old system information until you restart the module. Use this command to read the currently stored IP address and system information. Use the AT*AMSTAT to read the current IP address.

Input and Response Parameters

ip_addr netmask gw

Type Value

IP_Addr IP address for the device (default 172.23.56.99) IP_Addr Netmask for the device (default 255.255.255.0) IP_Addr The IP address of the gateway (default 172.23.56.99) store_in_startup_database integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*ANIP, , OK OK

Description

**4.2 AT*ANDHCP DCHP Activation**

Syntax Description

AT*ANDHCP=, < store_in_startup_database > Activate/deactivate DHCP If activated, this configuration will take precedence over the settings made with AT*ANIP. Use this command to read the current DHCP setting. AT*ANDHCP?

Input and Response Parameters Type Value

dhcp_mode integer 0: Static, enter a static IP address (default) 1: DHCP Client, acquire an IP address using DHCP 2: DHCP Server, use a static IP address and act as DHCP server 3: Auto IP, The BAT-C will be assigned a private IP address with a prefix of 169.254/16. 4: DHCP Relay, use a static IP address, and act as DHCP relay. 5: DHCP Client + DHCP Relay, acquire an IP address using DHCP, then act as DHCP relay (default) store_in_startup_database integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*ANDHCP: OK OK

Description

**4.3 AT*ANHN Hostname**

Syntax Description

AT*ANHN=, < store_in_startup_database > AT*ANHN? Use this command to write the HostName used with the dynamic DNS. Use this command to read the current HostName used with the dynamic DNS.

Input and Response Parameters

hostname

Type Value

string Use any string (default: "BAT-C") store_in_startup_database integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

Description

*ANHN: OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 45

**4.4 AT*ANDNS DNS Settings**

Syntax

AT*ANDNS?

Description

AT*ANDNS=,, Use this command to write the name server (DNS) information. Use this command to read the current name server (DNS) information.

Input and Response Parameters Type Value

dns1 dns2 IP_Addr This is the Primary DNS server. If DNS is not used, set this parameter to 0.0.0.0 (default 0.0.0.0). IP_Addr This is the Secondary DNS server. If DNS is not used or if one server is used, set this parameter to 0.0.0.0 (default 0.0.0.0). store_in_startup_database integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

OK ERROR

Description

*ANDNS:, OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 46 BAT-C Release 03 05/2016

5 Data Mode Commands

**5.1 AT*ADC Connect**

Syntax Description

AT*ADC Use this command to connect to a previously configured WLAN network.

Responses Description

*ADC: OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. ERROR This response indicates an unsuccessful execution of the write command.

**5.2 AT*ADCP Connect to BSSID**

Syntax Description

AT*ADCP=, , , Use this command to connect to a WLAN network. (Managed mode)

Input Parameters Type Value

BSSID network_type wlan_channel ssid Mac_Addr This is the BSSID of the desired AP. Integer Integer String 1 = Managed mode 0 = Auto (default) 1...11, 1...13 or 14 depending on regulatory domain setting for 2.4GHz. 36, 40, 44, 48 for 5GHz. This is the SSID of the desired AP. BAT-C Release 03 05/2016 47

**5.3 AT*ADCPN Connect to name (SSID)**

Syntax Description

AT*ADCPN=, , , Use this command to connect to a WLAN network specified by the SSID.

Input and Response Parameters Type Value

SSID network_type wlan_channel Reserved connection_handle

Responses

string This is the SSID of the desired AP or Ad Hoc unit. Integer 1 = Managed mode 2 = Ad-Hoc Integer 0 = Auto (default) 1 …11, 1…13 or 14 depending on regulatory domain setting for 2.4GHz 36, 40, 44, 48 for 5GHz. Integer This parameter is for future use. Integer 1=closes the current connection

Description

*ADCPN: OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. ERROR This response indicates an unsuccessful execution of the write command. 48 BAT-C Release 03 05/2016

**5.4 AT*ADCC Close Connection**

Syntax Description

AT*ADCC= This command Closes an existing network Connection.

Input Parameters Type Value

connection_handle

Responses

OK ERROR integer 1=closes the current connection

Description

This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 49

**5.5 AT*ADRDRP Read Default Remote Peer**

Syntax Description

AT*ADRDRP=

Input and Response Parameters Type

Use this command to read the current default peer.

Value

peer_id address conn_scheme update_on_incoming name

Responses

*ADRDRP:

, , , OK ERROR Integer The command returns a value between 0 and the response from AT*ADMRP – 1. String Address to the service on the remote peer. In the form of, ://ipaddr:port. i.e.: tcp://172.23.56.1:5130. Integer Ignored by the BAT-C 0 = Unused 1 = Connect on data (Connects when transmitting data, then remains connected.) 2 = Always connected (Connects right after power on.) Integer This parameter is for future use. String A string with a user defined name of the peer.

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates an unsuccessful execution of the write command. 50 BAT-C Release 03 05/2016

**5.6 AT*ADWDRP Write Remote Peer Information**

Syntax Description

AT*ADWDRP=,

, , , ,

Input Parameters Type

Use this command to write information for a remote peer.

Value

peer_id address conn_scheme reserved name Integer This is any value between 0 and the response from AT*ADMRP – 1. String Address to the service on the remote peer. In the form of, ://ipaddr:port. i.e.: udp://172.23.56.1:5130. Integer Ignored by the BAT-C Reserved, use 0 Integer This parameter is for future use. Use 0 String A string with a user defined name of the peer. store_in_startup_database Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses Description

OK ERROR This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 51

**5.7 AT*ADRL Roaming List**

Syntax Description

AT*ADRL? Use this command to read the current list of Access Points used for roaming.

Response Parameters Type Value

index bssid store_in_startup_database integer This is the position in the roaming list. Mac_Addr This is the BSSID of the Access Point. integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*ADRL:, OK

Description

The device sends this response for every AP in the list. ERROR This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 52 BAT-C Release 03 05/2016

**5.8 AT*ADRRL Read Roaming List**

Syntax Description

AT*ADRRL= This command reads the BSSID of the selected AP in the roaming list.

Input and Response Parameters Type Value

index bssid channel

Responses

integer integer This is the position in the roaming list. Mac_Addr This is the BSSID of the Access Point. This is the channel of the AP.

Description

*ADRRL:, OK ERROR The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 53

**5.9 AT*ADWRL Write Roaming List**

Syntax Description

AT*ADWRL=,,

Input Parameters Type

This command writes the BSSID of the AP in the roaming list.

Value

index bssid channel store_in_startup_database integer integer This is the position in the roaming list. Mac_Addr This is the BSSID of the Access Point. integer This is the channel of the AP. 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses Description

OK ERROR This response indicates a successful execution of the write command. Response to an unsuccessful execution of the write command. 54 BAT-C Release 03 05/2016

**5.10 AT*ADLNK Read WLAN link status**

Syntax Description

AT*ADLNK?

Response Parameters

Use this command to read the current WLAN link status.

Type Value

link_status integer 0: Not associated 1: Associated Mac_Addr BSSID of the WLAN network or N/A if not associated. bssid

Responses Description

*ADLNK:, OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. ERROR This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 55

6 Informational Commands

**6.1 AT*AILBA Read Local MAC Address**

Syntax Description

AT*AILBA?

Response Parameters

mac_addr

Responses

This command reads the MAC Address of the local device.

Type

Mac_Addr

Value

This is the Local MAC address.

Description

*AILBA: OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command.. ERROR This response indicates an unsuccessful execution of the write command. 56 BAT-C Release 03 05/2016

**6.2 AT*AILVI Local version**

Syntax Description

AT*AILVI? This command reads the local version information to the Ethernet Port Adapter.

Response Parameters

manufacturer

Type Value

String This is the Ethernet port adapter manufacturer, i.e. "Hirschmann". spa_sw_version String This is the Ethernet port adapter software version, i.e. "2.3.2 [11:32:15,May 14 2012]". wlan_driver_version wlan_fw_version String This is the WLAN host driver version, i.e. "2.12.1". String This is the WLAN firmware version, i.e. "3.2.8.5". wlan_hw_manufacturer String This is the WLAN hardware manufacturer, example "RPS".

Responses Description

*AILVI: , , , , OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. ERROR This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 57

7 Miscellaneous Commands

**7.1 AT*AMLI Log in**

Syntax Description

AT*AMLI= Use this command to Log in to the AT command interface. Note: The “User management S register” must be set to “enable user management ”.

Input Parameters Type Value

password

Responses

String This is a null terminated string of up to 15 bytes. OK

Description

This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command. 58 BAT-C Release 03 05/2016

**7.2 AT*AMLO Log Out**

Syntax Description

AT*AMLO=

Input Parameters Type

Use this command to Log out from the AT command interface.

Value

log_out

Responses

Integer 1= log out OK

Description

This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command.

**7.3 AT*AMGD General Data**

Syntax Description

AT*AMGD= Use this command to write data, to be stored between power cycles. AT*AMGD? Use this command to read the current previously written data.

Input and Response Parameters Type Value

String Represents the data to store, up to 31 bytes long. data

Responses

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. BAT-C Release 03 05/2016 59

Responses

OK ERROR

Description

This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command.

**7.4 AT*AMMP Max Output Power**

Syntax Description

AT*AMMP=, Use this command to write the max power settings. AT*AMMP? Use this command to read the current max power setting.

Input and Response Parameters Type Value

max_power store_in_startup_database

Responses

*AMMP: OK OK ERROR Integer This setting is the actual dBm. The valid range is between -14...15. Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 60 BAT-C Release 03 05/2016

**7.5 AT*AMWS Watchdog Settings**

Syntax Description

AT*AMWS=, , , , , Use this command to write the watchdog settings. The watchdog functionality will disconnect from a remote peer for one of the given conditions. AT*AMWS?

Input and Response Parameters

reserved1 Use this command to read the current watchdog settings.

Type Value

inactivity_timeout connect_timeout disconnect_reset reset store_in_startup_database Integer This parameter is for future use. This is a “0” for this parameter. Integer This is the time in seconds before the BAT-C resets if it receives no data on the WLAN interface. 0: Disabled (default value) > 0: Timeout in seconds Integer This is the Max connection time in seconds before the BAT-C resets. 0: Disabled (default value) > 0: Timeout in seconds Integer 0: Disabled (default value) 1: Enabled, the BAT-C will reset on a terminated connection. Integer 1: Reset the unit immediately. Will not store nor return any response. Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database. BAT-C Release 03 05/2016 61

Responses Description

*AMWS:, , , , OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. OK ERROR This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command.

**7.6 AT*AMESS Event and Status Subscriber**

Syntax Description

AT*AMESS=, , , , Use this command to write the Event and Status subscriber. AT*AMESS? Use this command to read the current Event and Status subscriber.

Input and Response Parameters Type Value

mac_addr ip_addr port MAC_Addr This is the MAC address of event subscriber. IP_Addr Integer This is the IP address of event subscriber. This is the port number of event subscriber 0: use default Layer-2 events, must be specified 62 BAT-C Release 03 05/2016

Input and Response Parameters

protocol

Type Value

store_in_startup_database Integer integer Manage event transmission using the following values. 0: disable (default) 1: Messages sent by AT over TCP 2: Messages sent by AT over Layer-2 (mac_address must be specified, FFFFFFFFFFFF means that it will be broadcasted) 3: Syslog 4 - 255: reserved 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*AMESS: ,,, OK OK ERROR

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command.

**7.7 AT*AMSMF SMART Mode (Button) functionality**

Syntax Description

AT*AMSMF=,, Use this command to write the SMART button functionality. AT*AMSMF? Use this command to read the current SMART button functionality. BAT-C Release 03 05/2016 63

Input and Response Parameters

short_mode

Type Value

long_mode store_in_startup_database Integer Manage the “Push” functionality with the following values. 0: Trigger roaming (disconnect/connect) 1: Toggle Leds 2: Soft reset Integer Manage the “Hold” functionality with the following values. 0: Trigger roaming (disconnect/connect) 1: Toggle Leds 2: Soft reset integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

ERROR

Description

*AMSMF: ,OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. OK This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 64 BAT-C Release 03 05/2016

**7.8 AT*AMSMFL SMART Mode Function List**

Syntax Description

AT*AMSMFL=, ,, ,, ,, ,, ,, ,, ,, Use this command to write the sequence of SMART button functionality modes. Example: "AT*AMSMFL=15,2,3,4,5,11,12,0,0,0,0,0,0,0,0,1" will limit the number of SMART modes to 7. The first mode indicated by the "A" LED will be 15 (see list below), the second, indicated by the "B" LED will be 2 and the third, indicated by "A" and "B", will be 3 and so on. See the product guide for more details. AT*AMSMFL? Use this command to read the current SMART button function list.

Input and Response Parameters Type Value

smart_mode_# store_in_startup_database Integer 0: End Smart mode function list 1 - 15 SMART functionality: 1: Exit Smart mode 2: Reset to factory defaults 3: Reset IP settings to factory defaults 4: Wait for Automatic configuration - Ad-Hoc 5: Initiate Automatic configuration - Ad-Hoc 6: Wait for Automatic configuration - Profinet - Ad-Hoc 7: Initiate Automatic configuration - Profinet - Ad-Hoc 8: Wait for Automatic configuration - Managed mode 9: Initiate Automatic configuration - Managed mode 10: Initiate Automatic configuration - Managed mode - wired 11: Configure Client mode 12: Initiate Automatic configuration - Ad-Hoc - Multipoint 13: Reserved 14: Reserved 15: Enable DHCP server 16 - 255: Reserved Default: 15,2,3,4,5,6,7,8,9,10,11,12 integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database. BAT-C Release 03 05/2016 65

Responses

ERROR

Description

*AMSMFL:, ,, ,, ,, ,, ,, ,, , OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. OK This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command.

**7.9 AT*AMSSC SNMP Sys Contact**

Syntax Description

AT*AMSSC=, Use this command to write the SNMP Sys Contact. AT*AMSSC? Use this command to read the current SNMP Sys Contact.

Input and Response Parameters Type Value

sys_contact store_in_startup_database String This is a desired string, up to 32 characters. integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses Description

*AMSSC: OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. 66 BAT-C Release 03 05/2016

Responses

OK ERROR

Description

This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command.

**7.10 AT*AMSSL SNMP Sys Location**

Syntax Description

AT*AMSSL=, AT*AMSSL? Use this command to write the SNMP Sys Location. Use this command to read the current SNMP Sys Location.

Input and Response Parameters

sys_Location

Type Value

store_in_startup_database String This is a desired string, up to 32 characters. integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

ERROR

Description

*AMSSL: OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. OK This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 67

**7.11 AT*AMSSS SNMP Sys Services**

Syntax Description

AT*AMSSS? Use this command to read the current SNMP Sys Services.

Response Parameters Type Value

sys_services Integer This parameter represents the system services defined by SNMP.

Responses Description

*AMSSS: OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. ERROR This response indicates an unsuccessful execution of the write command.

**7.12 AT*AMSBN SNMP Basic Name**

Syntax Description

Use this command to write the SNMP Basic Name. AT*AMSBN=, AT*AMSBN? Use this command to read the current SNMP Basic Name.

Input and Response Parameters

basic_name store_in_startup_database

Type Value

String This is a desired string, up to 32 characters. integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration 68 BAT-C Release 03 05/2016

Responses

*AMSBN: OK OK ERROR between power cycles by updating the settings database.

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command.

**7.13 AT*AMSBD SNMP Basic Descriptor**

Syntax Description

AT*AMSBD=, Use this command to write the SNMP Basic Descriptor. AT*AMSBD? Use this command to read the current SNMP Basic Descriptor.

Input and Response Parameters Type Value

basic_descriptor String This is a desired string, up to 32 characters. store_in_startup_database integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses Description

*AMSBD: OK< CR> The device displays the current parameter setting, followed by “OK“, after entering a successful read command. BAT-C Release 03 05/2016 69

Responses

OK ERROR

Description

This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command.

**7.14 AT*AMSSD SNMP Sys Description**

Syntax Description

AT*AMSSD=, Use this command to write the SNMP System Description. AT*AMSSD? Use this command to read the current SNMP System Description.

Input and Response Parameters Type Value

basic_description store_in_startup_database String This is a desired string, up to 32 characters. integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

OK ERROR

Description

*AMSBD: OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 70 BAT-C Release 03 05/2016

**7.15 AT*AMSWC SNMP Write Community (Private Community)**

Syntax Description

AT*AMSWC=, Use this command to write the SNMP Private Community name. The BAT-C currently supports 1 community that has both read and write access.

Input Parameters Type Value

community store_in_startup_database String This is a desired string, up to 12 characters. integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

Description

This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command. id

**7.16 AT*AMSEID SNMP Enterprise ID**

Syntax Description

AT*AMSEID? Use this command to read the current SNMP Enterprise Id.

Response Parameters Type Value

Integer This is an integer representing your company. BAT-C Release 03 05/2016 71

Responses

*AMSEID: OK ERROR

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates an unsuccessful execution of the write command.

**7.17 AT*AMTL TCP Listener**

Syntax

ERROR

Description

AT*AMTL=,, AT*AMTL? Use this command to enable or disable the TCP Listener. Use this command to read the current TCP Listener activation status.

Input and Response Parameters

enable

Type Value

Integer 0 = Disables TCP Listener 1 = Enables TCP Listener. When enabled, it will always enter at mode at startup Integer TCP port to listen for incoming connections port store_in_startup_database Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses Description

*AMTL:, OK OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 72 BAT-C Release 03 05/2016

**7.18 AT*AMUR UDP Receiver**

Syntax

AT*AMUR=,, AT*AMUR?

Description

Use this command to enable or disable the UDP Receiver. Use this command to read the current UDP receiver activation status.

Input and Response Parameters

enable

Type Value

port store_in_startup_database Integer 0 = Disables UDP Receiver 1 = Enables UDP Receiver Integer UDP port to listen for incoming packets Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*AMUR:, OK OK ERROR

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 73

**7.19 AT*AMHL HTTP Listener**

Syntax

AT*AMHL=,, AT*AMHL?

Description

Use this command to enable or disable the HTTP Listener. Use this command to read the current HTTP Listener status.

Input and Response Parameters

enable

Type Value

port store_in_startup_database

Responses

*AMHL:, OK OK ERROR Integer 0 = Disables HTTP Listener 1 = Enables HTTP Listener Integer TCP port to listen for incoming connections Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 74 BAT-C Release 03 05/2016

**7.20 AT*AMSR SNMP Receiver**

Syntax Description

AT*AMSR=,, Use this command to enable or disable the SNMP Receiver. AT*AMSR?

Input and Response Parameters

Use this command to read the current SNMP Receiver status.

Type Value

enable port Integer 0 = Disables SMNP Receiver 1 = Enables SNMP Receiver Integer This is the UDP port to listen for incoming packets. store_in_startup_database Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

*AMSR:, OK OK ERROR

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 75

**7.21 AT*AMLCR Link Config Receiver**

Syntax Description

AT*AMLCR=,, AT*AMLCR? Use this command to enable or disable the Link Configuration Receiver. Use this command to read the current Link Configuration Receiver status.

Input and Response Parameters Type Value

enable Integer 0 = Disables Link Config Receiver 1 = Enables Link Config Receiver Integer Ethernet type that will be passed up the AT parser eth_type store_in_startup_database Integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses

OK ERROR

Description

*AMLC:, OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 76 BAT-C Release 03 05/2016

**7.22 AT*ACEW Configure Mode**

Syntax

AT*ACEW=,, AT*ACEW?

Description

Use this command to configure and enter Client mode. Use this command to read the current Wireless LAN MAC address and mode.

Input and Response Parameters Type Value

mac_addr enter mode store_in_startup_database

Responses

*ACEW:, OK OK ERROR MAC_Addr MAC address to use in Client and Multi-Client mode. (Ignored if second parameter = 1) Integer Integer integer 0: Configure Client mode (The device issues a reset of the module.) 1: Configure Ethernet Bridge mode 2: Reserved 3: Configure Multi-Client mode 0: Client mode 1: Ethernet Bridge Mode 3: Multi-Client mode 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Description

The device displays the current parameter setting, followed by “OK“, after entering a successful read command. This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 77

**7.23 AT*AMEO Set External Digital Output**

Syntax Description

AT*AMEO=

Input Parameters Type

Use this command to set External digital Output to value.

Value

value integer 0: LOW - Ground (0V DC) 1: HIGH – The voltage will be set to the corresponding value on the power connector, A-coded male M12, pinning number 5 (typical 12-24 V DC).

Responses Description

OK This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command.

**7.24 AT*AMSTAT Read Current Status**

Syntax Description

AT*AMSTAT=, Use this command to read the current status of a specific interface.

Input and Response Parameters Type Value

level integer 1 = Common 2 = Reserved 3 = WLAN 4 = Reserved 5 = Ethernet 6 = Reserved 7 = Reserved 78 BAT-C Release 03 05/2016

Input and Response Parameters

id uptime wlan_mac_addr wlan_status op_mode ssid bssid data_rate rssi channel eth_mac_addr eth_status ip_addr subnet gateway dhcp_mode dns1 dns2

Type

integer integer MAC_Addr integer integer string MAC_Addr integer integer integer MAC_Addr integer IP_Addr IP_Addr IP_Addr integer IP_Addr IP_Addr

Value

0 = This entry is optional. This is the uptime in seconds. This is the WLAN MAC address. 0 = Not associated 1 = Associated 1 = Managed 2 = Ad-hoc This is the SSID of the AP. This is the BSSID of the AP or associated device. See AT*AGRTE for further details. See AT*AGRSS for further details. This is the Channel. This is the Ethernet MAC address. Lists the Ethernet Link Status 0: Link is down 1: Link is up This is the Static IP address or assigned IP address when using DHCP. This is the Subnet mask. This is the Gateway IP address. This is the DHCP mode, see AT*ANDHCP for further details. This is the Primary DNS server. This is the Secondary DNS server. BAT-C Release 03 05/2016 79

Responses Description

*UPTIME: OK The device returns with this response for integer 1. The device responds with this information for the common command, followed by an “OK”. The device returns with this response for integer 2. OK *HW_ADDR: *STATUS: *OP_MODE: *SSID: *BSSID: *TX_RATE: *RSSI: *CHANNEL: OK The device returns with this response for integer 3. The device responds with this list of information for the WAN command. The device displays the WLAN, TX_RATE , RSSI and CHANNEL values when connected. OK The device returns with this response for integer 4. *HW_ADDR: *STATUS: *IP_ADDR: *SUBNET_MASK: *GATEWAY: *DHCP: *DNS1: *DNS2: OK The device returns with this response for integer 5. The device responds with this list of information for the Ethernet command, foll owed by an “OK”. OK OK ERROR The device returns with this response for integer 6. The device returns with this response for integer 7. This response indicates an unsuccessful execution of the write command. 80 BAT-C Release 03 05/2016

**7.25 AT*AMWID Wireless interface disable**

Syntax

AT*AMWID?

Description

AT*AMWID=, Use this command to Disable the Wireless Interface. Use this command to read the Wireless Interface Disabled status.

Input and Response Parameters

disable

Type Value

store_in_startup_database integer 0: Wireless interface enabled 1: Wireless interface is disabled integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database.

Responses Description

*AMWID: OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. OK This response indicates a successful execution of the write command. ERROR This response indicates an unsuccessful execution of the write command. BAT-C Release 03 05/2016 81

**7.26 AT*AMPSM Profisafe Mode**

Syntax

AT*AMPSM=, ,

Description

Use this command to enable ProfiSafe Mode. This command disables the write configuration mode. However, with the ProfiSafe Mode enabled, you are able to read the configuration on the device. To amend the configuration, set the device in configuration mode with “AT*ACEW” or reset to factory defaults with “AT&F0”. Use this command to read the ProfiSafe Mode Status. AT*AMPSM?

Input and Response Parameters

ps_mode

Type Value

store_in_startup_database apply_without_restart integer 0: ProfiSafe Mode disabled 1: ProfiSafe Mode enabled integer 0: The setting is valid for the current power cycle. 1: The Ethernet Port Adapter retains the configuration between power cycles by updating the settings database. integer This entry is optional. 1: The device enters the ProfiSafe Mode directly without a restart when setting this entry to 1. This command disables the write configuration mode immediately after execution.

Responses Description

*AMPSM: OK The device displays the current parameter setting, followed by “OK“, after entering a successful read command. OK ERROR This response indicates a successful execution of the write command. This response indicates an unsuccessful execution of the write command. 82 BAT-C Release 03 05/2016

8 Events

**8.1 *ADCPO Connection Up**

Event Description

*ADCPO:, , ,

Input and Response Parameters

After establishing a connection to a remote device, the BAT-C transmits the event.

Type Value

connection_handle network_type integer integer Identifies the connection. 1: Managed 2: Ad Hoc mac_addr bssid Mac_Addr Local mac address Mac_Addr Bssid of the network we are connected to.

**8.2 *ADCCO Connection Closed**

Event Description

*ADCCO:, , , After disconnecting from a remote device, the BAT-C transmits the event.

Input and Response Parameters Type Value

connection_handle integer Identifies the connection. BAT-C Release 03 05/2016 83

Input and Response Parameters

reason mac_addr bssid

Type Value

integer 0: Disconnected by command 1: Disconnected by link loss 255: Reason unknown Mac_Addr Local MAC address. Mac_Addr Bssid of the network we were previously connected to.

**8.3 *AMDST Digital Signal Transition**

Event Description

*AMDST: The device transmits theis event after detecting an external Digital Signal Transition.

Parameters

mac_addr

Type Value

Mac_Addr MAC address of the device.

**8.4 *AMRSS Low RSSI Warning**

Event

*AMRSS:,

Response Parameters Type

mac_addr rssi

Licenses

Description

The RSSI value is below -70 dBm.

Value

Mac_Addr MAC address of the device. Integer RSSI value 84 BAT-C Release 03 05/2016

A Further Support

■

Technical Questions

For technical questions, please contact any Hirschmann dealer in your area or Hirschmann directly. You will find the addresses of our partners on the Internet at http://www.hirschmann.com Contact our support at https://hirschmann-support.belden.eu.com You can contact us in the EMEA region at ► ► Tel.: +49 (0)1805 14-1538 E-mail: [email protected] in the America region at ► ► Tel.: +1 (717) 217-2270 E-mail: [email protected] in the Asia-Pacific region at ► ► Tel.: +65 68549860 E-mail: [email protected] ■

Hirschmann Competence Center

The Hirschmann Competence Center is ahead of its competitors: ► ► ► ► Consulting incorporates comprehensive technical advice, from system evaluation through network planning to project planning. Training offers you an introduction to the basics, product briefing and user training with certification. The current training courses to technology and products can be found at http://www.hicomcenter.com Support ranges from the first installation through the standby service to maintenance concepts. With the Hirschmann Competence Center, you have decided against making any compromises. Our client-customized package leaves you free to choose the service components you want to use. Internet: http://www.hicomcenter.com BAT-C Release 03 05/2016 85

Hello! I am an AI chatbot specifically trained to assist you with the Hirschmann BAT-C Reference manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant is out of keyboard. Please, try again later.

CLI-Reference Industrial Wireless LAN Client BAT-C

Contents

About this manual

Related Documents

1 AT command syntax

1.1 Command Line Format

1.2 Limitations

1.3 Data Types

String

Octet String

Integer

IP_Addr

MAC_Addr

2 Standard AT Commands

2.1 AT Attention Command

2.2 AT* List Available Commands

2.3 AT&F Restore to Factory Settings

2.4 AT&F0 Restore to Factory Settings

2.5 ATE Echo Off

2.6 ATE Echo On/Off

2.7 ATQ Result Codes On/Off

2.8 ATS2 Escape Character

2.9 ATS3 Command Line Termination Character

2.10 ATS4 Response Formatting Character

2.11 ATS5 Response Formatting Character

2.12 ATS General Settings S Register Manipulation

3 Link Layer Commands

3.1 AT*AGAM Authentication Mode

3.2 AT*AGEM Encryption Mode

3.3 AT*AGSM Security Mode

3.4 AT*AGOM Operational Mode

3.5 AT*AGFP Encryption/Authentication Key

3.6 AT*AGFPWI Write Encryption/Authentication Key (with Index)

3.7 AT*AGAFP Active Encryption/Authentication Key

3.8 AT*AGUN Username

3.9 AT*AGDN Domain name

3.10 AT*AGCFP Certificate Fingerprint

3.11 AT*AGSSID Network Name (SSID)

3.12 AT*AGRSS RSSI Value

3.13 AT*AGCH Channel Number

3.14 AT*AGCL Channel List

3.15 AT*AGSCAN

3.16 AT*AGRTE Data Rate and Link Adaptation

4 Network Layer Commands

4.1 AT*ANIP IP Settings

4.2 AT*ANDHCP DCHP Activation

4.3 AT*ANHN Hostname

4.4 AT*ANDNS DNS Settings

5 Data Mode Commands

5.1 AT*ADC Connect

5.2 AT*ADCP Connect to BSSID

5.3 AT*ADCPN Connect to name (SSID)

5.4 AT*ADCC Close Connection

5.5 AT*ADRDRP Read Default Remote Peer

5.6 AT*ADWDRP Write Remote Peer Information

5.7 AT*ADRL Roaming List

5.8 AT*ADRRL Read Roaming List

5.9 AT*ADWRL Write Roaming List

5.10 AT*ADLNK Read WLAN link status

6 Informational Commands

6.1 AT*AILBA Read Local MAC Address

6.2 AT*AILVI Local version

7 Miscellaneous Commands

7.1 AT*AMLI Log in

7.2 AT*AMLO Log Out

7.3 AT*AMGD General Data

7.4 AT*AMMP Max Output Power

7.5 AT*AMWS Watchdog Settings

7.6 AT*AMESS Event and Status Subscriber

7.7 AT*AMSMF SMART Mode (Button) functionality

7.8 AT*AMSMFL SMART Mode Function List

7.9 AT*AMSSC SNMP Sys Contact

7.10 AT*AMSSL SNMP Sys Location

7.11 AT*AMSSS SNMP Sys Services

7.12 AT*AMSBN SNMP Basic Name

7.13 AT*AMSBD SNMP Basic Descriptor

7.14 AT*AMSSD SNMP Sys Description

7.15 AT*AMSWC SNMP Write Community (Private Community)

7.16 AT*AMSEID SNMP Enterprise ID

7.17 AT*AMTL TCP Listener

**2.2 AT* List Available Commands**

**3.1 AT*AGAM Authentication Mode**

**3.2 AT*AGEM Encryption Mode**

**3.3 AT*AGSM Security Mode**

**3.4 AT*AGOM Operational Mode**

**3.5 AT*AGFP Encryption/Authentication Key**

**3.6 AT*AGFPWI Write Encryption/Authentication Key (with Index)**

**3.7 AT*AGAFP Active Encryption/Authentication Key**

**3.8 AT*AGUN Username**

**3.9 AT*AGDN Domain name**

**3.10 AT*AGCFP Certificate Fingerprint**

**3.11 AT*AGSSID Network Name (SSID)**

**3.12 AT*AGRSS RSSI Value**

**3.13 AT*AGCH Channel Number**

**3.14 AT*AGCL Channel List**

**3.15 AT*AGSCAN**

**3.16 AT*AGRTE Data Rate and Link Adaptation**

**4.1 AT*ANIP IP Settings**

**4.2 AT*ANDHCP DCHP Activation**

**4.3 AT*ANHN Hostname**

**4.4 AT*ANDNS DNS Settings**

**5.1 AT*ADC Connect**

**5.2 AT*ADCP Connect to BSSID**

**5.3 AT*ADCPN Connect to name (SSID)**

**5.4 AT*ADCC Close Connection**

**5.5 AT*ADRDRP Read Default Remote Peer**

**5.6 AT*ADWDRP Write Remote Peer Information**

**5.7 AT*ADRL Roaming List**

**5.8 AT*ADRRL Read Roaming List**

**5.9 AT*ADWRL Write Roaming List**

**5.10 AT*ADLNK Read WLAN link status**

**6.1 AT*AILBA Read Local MAC Address**

**6.2 AT*AILVI Local version**

**7.1 AT*AMLI Log in**

**7.2 AT*AMLO Log Out**

**7.3 AT*AMGD General Data**

**7.4 AT*AMMP Max Output Power**

**7.5 AT*AMWS Watchdog Settings**

**7.6 AT*AMESS Event and Status Subscriber**

**7.7 AT*AMSMF SMART Mode (Button) functionality**

**7.8 AT*AMSMFL SMART Mode Function List**

**7.9 AT*AMSSC SNMP Sys Contact**

**7.10 AT*AMSSL SNMP Sys Location**

**7.11 AT*AMSSS SNMP Sys Services**

**7.12 AT*AMSBN SNMP Basic Name**

**7.13 AT*AMSBD SNMP Basic Descriptor**

**7.14 AT*AMSSD SNMP Sys Description**

**7.15 AT*AMSWC SNMP Write Community (Private Community)**

**7.16 AT*AMSEID SNMP Enterprise ID**

**7.17 AT*AMTL TCP Listener**

**7.18 AT*AMUR UDP Receiver**

**7.19 AT*AMHL HTTP Listener**

**7.20 AT*AMSR SNMP Receiver**

**7.21 AT*AMLCR Link Config Receiver**

**7.22 AT*ACEW Configure Mode**

**7.23 AT*AMEO Set External Digital Output**

**7.24 AT*AMSTAT Read Current Status**

**7.25 AT*AMWID Wireless interface disable**

**7.26 AT*AMPSM Profisafe Mode**

**8.1 *ADCPO Connection Up**

**8.2 *ADCCO Connection Closed**

**8.3 *AMDST Digital Signal Transition**

**8.4 *AMRSS Low RSSI Warning**