Earthquake K33 CHIPPER SHREDDER TAZZ VIPER 301CC Operator's Manual

ENGLISH
Owner’s Manual
CHIPPER SHREDDER
Model #’s: 18493 / 22752 /
22754 / 30520 / 32013
50:1
SERIAL NO.
DATE OF PURCHASE:
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Get parts or technical assistance online at
www.GetEarthquake.com or call (800) 345-6007
© 2018 Ardisam
All Rights Reserved
GAS/OIL
RATIO
P/N: 32409
REV 1: 08/29/2018
Owner’s Manual
CHIPPER SHREDDER
STOP! ACTIVATE YOUR WARRANTY BEFORE USE
All products must be registered within 30 days from the date of purchase in order to be covered under
warranty. For more information regarding Warranty and Registration please review the Warranty and Registration terms and conditions expressed in the warranty insert.
INTRODUCTION
Thank you for purchasing your product from Earthquake®. We have worked to ensure that this product meets the highest standards for usability and durability. With proper care, your purchase will provide many years of service.
Please read this entire manual before installation and use. Earthquake® reserves the right to change, alter or improve the product
and this document at any time without prior notice. Due to continuous product improvements, product images may not be exact.
Some assembly may be required.
Read and keep this manual for future reference. This manual contains important information regarding safety, assembly, operation
and maintenance. The owner must be certain that all the product information is included with the unit. This information includes
the manual, the replacement parts and the warranties. This information must be included to make sure state laws and other laws
are followed. All persons to whom rent/loan this unit must have access to and understand this information. This manual should
remain with the product even if it is resold.
CONTENTS
Introduction/Contents...................................................................................................................................................................................................................2
Bolt Identification Chart.................................................................................................................................................................................................................3
Warnings and Safety Precautions........................................................................................................................................................................................... 4-9
Features.............................................................................................................................................................................................................................................10
Specifications...................................................................................................................................................................................................................................11
Unpacking and Assembly.................................................................................................................................................................................................... 12-14
Operation................................................................................................................................................................................................................................... 15-16
Maintenance and Storage.................................................................................................................................................................................................... 17-19
Troubleshooting and Repair................................................................................................................................................................................................ 20-22
REGISTRATION AND SERVICE
Record the product model number and serial number in the
space provided for easy reference when ordering parts or
requesting technical support. Excluding emissions-related
warranty items, the warranty is valid only if the completed
registration is received by Ardisam within 30 days of purchase. You can register your warranty online by visiting www.
GetEarthquake.com, or by mailing it to: Ardisam, 1160 8th
Avenue, Cumberland, WI 54829. You may also call our Customer Service department at (800) 345-6007 Mondays through
Fridays from 8 a.m. to 5 p.m. CST.
2
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
Serial
Number
Decal
Owner’s Manual
CHIPPER SHREDDER
BOLT IDENTIFICATION CHART
Bolts shown are for size reference only. Extra hardware may be
included in the parts bag.
(A)
M8 x 40 MM Bolt
Qty 4
(B)
M8 x 20 MM Flange Bolt
Qty 4
(G)
M8 Nut
Qty 8
(H)
M8 Nyloc Nut
Qty 3
(I)
M6 Nut
Qty 3
(C)
M6 x 16 MM Bolt
Qty 3
TOOLS NEEDED - NOT INCLUDED
(D)
12 X 24 MM Washer
Qty 2
(E)
M8 Washer
Qty 12
8 MM Wrench - Qty 1
10 MM Wrench - Qty 1
(F)
M6 Spring Lock Washer
Qty 3
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
3
Owner’s Manual
CHIPPER SHREDDER
WARNINGS AND SAFETY PRECAUTIONS
OWNER’S RESPONSIBILITY
Accurate assembly and safe and effective use of the machine is
the owner’s responsibility.
•
Read and follow all safety instructions.
•
Carefully follow all assembly instructions.
•
Maintain the machine according to directions and
schedule included in this Earthquake® operator’s manual.
•
Ensure that anyone who uses the machine is familiar with
all controls and safety precautions.
SPECIAL MESSAGES
Your manual contains special messages to bring attention to
potential safety concerns, machine damage as well as helpful
operating and servicing information. Please read all the information carefully to avoid injury and machine damage.
NOTE: General information is given throughout the manual
that may help the operator in the operation or service of the
machine.
This symbol points out important safety instructions
which if not followed could endanger your personal
safety. Read and follow all instructions in this manual
before attempting to operate this equipment.
BEFORE OPERATING EQUIPMENT:
Please read this section carefully. Read entire operating and
maintenance instructions for this product. Failure to follow instructions could result in serious injury or death. Operate the
machine according to the safety instructions outlined here and
inserted throughout the text. Anyone who uses this machine
must read the instructions and be familiar with the controls.
NOTICE
NOTICE INDICATES YOUR EQUIPMENT CAN BE DAMAGED
IF THE SAFETY INSTRUCTIONS THAT FOLLOW THIS SIGNAL
WORD ARE NOT OBEYED.
IMPORTANT
IMPORTANT INDICATES HELPFUL INFORMATION FOR
PROPER ASSEMBLY, OPERATION OR MAINTENANCE OF
YOUR EQUIPMENT.
CAUTION
CAUTION INDICATES A HAZARD WHICH, IF NOT AVOIDED,
COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY
DAMAGE.
WARNING
WARNING INDICATES A HAZARD WHICH, IF NOT AVOIDED,
COULD RESULT IN DEATH OR SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
DANGER
DANGER INDICATES A HAZARD WHICH, IF NOT AVOIDED,
CERTAINLY WILL RESULT IN DEATH OR SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
WARNING
YOU MUST READ, UNDERSTAND AND COMPLY WITH ALL
SAFETY AND OPERATING INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO SETUP AND OPERATE YOUR
MACHINE.
FAILURE TO COMPLY WITH ALL SAFETY AND OPERATING
INSTRUCTIONS CAN RESULT IN LOSS OF MACHINE
CONTROL, SERIOUS PERSONAL INJURY TO YOU AND/OR
BYSTANDERS, AND RISK OF EQUIPMENT AND PROPERTY
DAMAGE. THE TRIANGLE IN THE TEXT SIGNIFIES
IMPORTANT CAUTIONS OR WARNINGS WHICH MUST BE
FOLLOWED.
4
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
Owner’s Manual
CHIPPER SHREDDER
GENERAL OPERATING SAFETY
•
•
DANGER
Read the operating and service instruction manual
carefully. Be throughly familiar with the controls and the
proper use of the equipment. Know how to stop the unit
and disengage the controls quickly.
THE CHIPPER SHREDDER HAS SPINNING BLADES THAT
CAN AMPUTATE HANDS AND FEET. DO NOT PLACE HANDS
OR FEET IN THE HOPPER OR CHIPPER CONE, OR DISCHARGE
CHUTE.
Do not operate the equipment without wearing adequate
outer garments and safety goggles. Avoid loose-fitting
clothes and use protective footwear that will improve
footing on slippery surfaces.
•
Dress appropriately when operating the chipper shredder.
Always wear sturdy footwear and safety goggles. Never
wear sandals, sneakers or open shoes, and never operate
the chipper shredder with bare feet. Do not wear loose
clothing that might get caught in moving parts.
•
Never allow children to operate the equipment. Never
allow adults to operate the equipment without proper
instruction.
•
Only allow responsible adults, who are familiar with the
instructions, to operate the unit (local regulations can
restrict operator age).
•
Keep the area of operation clear of all persons, particularly
small children and pets.
•
Always maintain secure footing and solid balance while
starting or operating the chipper shredder. Never lean
directly over the machine.
•
Never operate the machine at high transport speeds on
hard or slippery surfaces.
•
Operate the machine only in daylight or good artificial
light.
•
Do not operate the unit while under the influence of alcohol or drugs.
•
Exercise caution to avoid slipping or falling.
•
Always wear eye and hearing protection when operating
this unit.
•
Keep in mind the operator is responsible for accidents
occurring to other people or property.
•
Never operate the machine without proper guards, plates,
or other safety protective devices in place.
•
Do not put hands or feet near or under rotating parts or at
inlet or discharge openings.
•
Thoroughly inspect where equipment is to be used and
remove all foreign objects.
WARNING
COMBUSTIBLE DEBRIS CAN CATCH FIRE. IT IS A VIOLATION
OF CALIFORNIA PUBLIC RESOURCE CODE, SECTION 4442,
TO USE OR OPERATE ENGINE-POWERED PRODUCTS
ON ANY FOREST-COVERED, BRUSH-COVERED, OR GRASSCOVERED LAND UNLESS THE EXHAUST SYSTEM IS
EQUIPPED WITH A SPARK ARRESTER, AS DEFINED IN
SECTION 4442, MAINTAINED IN EFFECTIVE WORKING
ORDER. OTHER STATES OR FEDERAL JURISDICTIONS MAY
HAVE SIMILAR LAWS. CONTACT THE ORIGINAL EQUIPMENT
MANUFACTURER, RETAILER, OR DEALER TO OBTAIN A
SPARK ARRESTER DESIGNED FOR USE WITH THIS PRODUCT.
WARNING
THIS UNIT DISCHARGES DEBRIS AT HIGH SPEEDS. ALWAYS
WEAR PROTECTIVE GOGGLES AND DO NOT OPERATE
WITHOUT THE DEBRIS BAG IN PLACE.
DO NOT ALLOW ANYONE IN THE AREA WHILE THE UNIT IS
RUNNING. IF SOMEONE DOES ENTER THE AREA, SHUT THE
UNIT OFF IMMEDIATELY UNTIL THEY LEAVE. ORGANIZE
THE WORK AREA PRIOR TO STARTING WORK.
•
Exercise extreme caution when operating on or crossing
gravel drives, walks or roads. Stay alert for hidden hazards
or traffic.
•
Never allow bystanders near the unit while running.
•
Do not put hands or feet near rotating parts or under the
machine. Keep clear of the discharge opening at all times.
•
Always operate the chipper shredder outdoors, on a firm,
level, earthen or grassy surface where the unit will be
stable and stay in position. Never attempt to operate the
unit on a slope, or on a wet or slippery surface where you
could slip and fall toward the chipper cone or hopper
openings.
•
If the machine should start to vibrate abnormally, stop
the engine (motor) and check immediately for the cause.
Vibration is generally a warning sign of trouble.
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
5
Owner’s Manual
CHIPPER SHREDDER
•
Do not operate without the debris bag in place because
this unit discharges debris at high speeds. If the unit is
operated on hard ground, asphalt, concrete, or other hard
surfaces without the collection bag in place. Material can
ricochet off of the hard surface and cause an unsafe condition for users and bystanders.
•
Always obey the size limitations for tree limbs and branches stated in the Waste Materials Guide portion of this
manual.
•
Never leave the machine running unattended. Always turn
off the engine, wait for the rotor to come to a complete
stop, and disconnect the spark plug before leaving the
area. Always move the unit to a safe storage area when
not in use.
•
Never direct discharge material toward anyone. Avoid discharging material against a wall or obstruction. Material
may ricochet back toward the operator.
•
Always stand to the side of the chipper cone when feeding tree limbs and branches into the unit, as tree limbs,
branches, and harder woods may kick back while being
chipped.
•
Always keep hands out of the chipper cone and shredder
hopper when feeding materials. Never wrap fingers tightly
around branches as you are feeding them into the unit,
as a sudden inward surge could pull your hands and arms
into the unit.
•
Never allow material to build up in the discharge area or
shredding chamber, as this may cause new material being
fed into the machine to kickback with sufficient force to
injure you or other bystanders.
•
Never allow material to build up around the engine during
chipper shredder operation. This could result in a fire, or
overheating of the engine.
•
Take all possible precautions as recommended by the
manufacturer when leaving the machine unattended.
•
Do not overload the machine by attempting to chip or
shred any material beyond manufacturers recommendations.
•
Use extreme caution when reversing or pulling the machine towards you.
•
Do not change the engine governor settings or overspeed
the engine.
•
Never attempt to reposition or move the chipper shredder
unit while it is running. Doing so could cause the machine
6
to tip over, and reaching to steady the unit could result in
accidental insertion of your hands into the chipper cone
or shredder hopper areas.
•
Never continue to operate the machine if it starts making
unusual noise or vibration. Shut the engine off immediately, allow the rotor to stop, disconnect the spark plug wire
and secure the wire away from the spark plug. Inspect
the unit for any signs of damage or foreign material in the
chipping or shredding areas. Remove any solid material
that may be preventing the unit from operating properly.
•
Never attempt to clear clogs from the chipper cone, shredder hopper or discharge chute while the unit is running.
Always shut the engine off, allow the rotor to come to a
complete stop, and remove the spark plug wire from the
spark plug before removing excess materials.
•
Never attempt to perform any maintenance, repairs, or attachment of accessories while the unit is running. Always
shut the unit off, allow the rotor to come to a complete
stop, and remove the spark plug wire from the spark plug
before beginning these activities.
•
Always make sure that the shredding chamber, shredder
hopper, and chipper cone are empty before starting the
unit after it has been idle. Attempting to start the unit with
material in these areas could cause the engine starting
cord to stop suddenly, injuring your hand and fingers, or
toppling the unit over. Vibration is generally a warning
sign of trouble.
•
Use only attachments and accessories approved of by the
manufacturer of the machine.
•
Make sure chipper shredder is free of debris before starting the engine.
•
Never attempt to make any adjustments while the engine
is running.
•
After striking a foreign object, stop the engine (motor),
remove spark plug wire, and wait for all moving parts to
come to a complete stop. Thoroughly inspect the machine
for any damage, repair the damage before restarting and
operating the machine.
•
Start the engine or switch on the motor carefully according to the manufacturers instructions. Keep hands and
feet away from inlet and discharge areas.
•
Never pick up or carry the machine while the engine is
running.
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
Owner’s Manual
CHIPPER SHREDDER
ENGINE SPECIFIC SAFETY
•
•
WARNING
Before cleaning, repairing, or inspecting, shut off the
engine and make certain that all moving parts have come
to a complete stop. Disconnect the spark plug wire and
secure the wire away from the spark plug to prevent accidental starting.
ENGINE GIVES OFF CARBON MONOXIDE, AN ODORLESS,
COLORLESS, POISON GAS. CARBON MONOXIDE MAY BE
PRESENT EVEN IF YOU DO NOT SMELL OR SEE ANY ENGINE
EXHAUST. BREATHING CARBON MONOXIDE CAN CAUSE
NAUSEA, FAINTING OR DEATH, IN ADDITION TO
DROWSINESS, DIZZINESS AND CONFUSION. IF YOU
EXPERIENCE ANY OF THESE SYMPTOMS, SEEK FRESH AIR
AND MEDICAL ATTENTION IMMEDIATELY.
Stop the engine (motor) when leaving the operating
position and when making any repairs, adjustments and
inspections.
MAINTENANCE AND STORAGE
•
Keep machine, attachments, and accessories in safe working condition.
•
Check engine mounting bolts and other hardware at frequent intervals for proper tightness to be sure the equipment is in safe working condition.
•
Never store machine with fuel in the fuel tank inside a
building where ignition sources are present, such as hot
water and space heaters, clothes dryers and the like. Allow
the engine to cool before storing in any enclosure.
•
Always refer to the operator’s manual for important details
if the machine is to be stored for an extended period.
•
If the fuel tank has to be drained, do this outdoors.
•
Follow the manufacturer’s recommendations for safe loading, unloading and storage of machine.
IF YOUR MACHINE COMES WITH A SEPARATE ENGINE
MANUAL, BE SURE TO READ AND FOLLOW ALL SAFETY AND
WARNING PRECAUTIONS OUTLINED THERE, IN ADDITION
TO ANY IN THIS MANUAL.
WARNING
FUEL IS HIGHLY FLAMMABLE. TAKE THE FOLLOWING
PRECAUTIONS:
• STORE FUEL IN CONTAINERS SPECIFICALLY DESIGNED FOR
THIS PURPOSE.
• REFUEL OUTDOORS ONLY AND DO NOT SMOKE WHILE
REFUELING.
• ADD FUEL BEFORE STARTING THE ENGINE. NEVER REMOVE
THE CAP ON THE FUEL TANK OR ADD FUEL WHILE THE
ENGINE IS RUNNING OR WHEN THE ENGINE IS HOT.
• IF FUEL IS SPILLED, DO NOT ATTEMPT TO START THE
ENGINE BUT MOVE THE MACHINE AWAY FROM THE AREA
OF SPILLAGE AND AVOID CREATING ANY SOURCE OF
IGNITION UNTIL FUEL VAPORS HAVE DISAPPEARED.
PREVENTING CARBON MONOXIDE POISONING
•
Always start and run engine outdoors. Do not start or run
engine in an enclosed area, even if doors or windows are
open.
•
Never try to ventilate engine exhaust indoors. Carbon
monoxide can reach dangerous levels very quickly.
•
Never run engine outdoors where exhaust fumes may be
pulled into a building.
•
Never run engine outdoors in a poorly ventilated area
where the exhaust fumes may be trapped and not easily
taken away. (Examples include: in a large hole or areas
where hills surround your working area.)
•
•
• REPLACE ALL FUEL TANK AND CONTAINER CAPS SECURELY.
•
Never point the exhaust muffler towards anyone. People
should always be many feet away from the operation of
the engine and its attachments.
•
Do not change the engine governor settings or overspeed the engine.
•
Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect.
GASOLINE FIRES AND HANDLING FUEL SAFELY
Never run engine in an enclosed or partially enclosed area.
(Examples include: buildings that are enclosed on one or
more sides, under tents, car ports or basements.)
•
Use extra care in handling gasoline and other fuels. They
are flammable and vapors are explosive.
Always run the engine with the exhaust and muffler pointed in the direction away from the operator.
•
When storing extra fuel be sure that it is in an appropriate
container and away from any fire hazards.
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
7
Owner’s Manual
CHIPPER SHREDDER
•
•
Prevent fire and explosion caused by static electric
discharge. Use only nonmetal, portable fuel containers
approved by the Underwriter’s Laboratory (U.L.) or the
American Society for Testing & Materials.
Always fill fuel tank outside in a well ventilated area. Never
fill your fuel tank with fuel indoors. (Examples include:
basement, garage, barn, shed, house, porch, etc.) Never
fill tank near appliances with pilot lights, heaters, or other
ignition sources. If the fuel has to be drained, this should
be done outdoors. The drained fuel should be stored in a
container specifically designed for fuel storage or it should
be disposed of carefully.
fuel such equipment on a trailer with a portable container,
rather than from a gasoline dispenser nozzle.
BURNS AND FIRES
•
The muffler, muffler guard and other parts of the engine
become extremely hot during the operation of the engine.
These parts remain extremely hot after the engine has
stopped.
PREVENTION OF BURNS AND FIRES
•
Never remove the muffler guard from the engine.
•
Never touch the muffler guard because it is extremely hot
and will cause severe burns.
•
Never touch parts of the engine that become hot after
operation.
Always keep materials and debris away from muffler guard
and other hot parts of the engine to avoid fires.
•
Never remove the fuel cap or add fuel with the engine
running. Stop engine and allow to cool before filling.
•
Do not smoke while refueling or operating engine.
•
Never drain fuel from the engine in an enclosed area.
•
•
Always wipe up excess (spilled) fuel from engine before
starting. Clean up spilled fuel immediately. If fuel is spilled,
do not start the engine but move machine and fuel container from area. Clean up spilled fuel and allow to evaporate
and dry after wiping and before starting.
CHILDREN AND BYSTANDERS
•
Allow fuel fumes/vapors to escape from the area before
starting engine.
•
Test the fuel cap for proper installation before starting and
using engine.
•
Always run the engine with fuel cap properly installed on
the engine.
•
During storage, keep machine so gas cap is up.
•
Never siphon fuel by mouth to drain fuel tank.
•
Always have an adult fill the fuel tank and never allow
children to fill the engine.
•
Never allow an adult or anyone under the influence of
drugs or alcohol to fill engine.
•
When storing gasoline or equipment with fuel in the tank,
store away from furnaces, stoves, water heaters or other
appliances that have a pilot light or other ignition source
because they can ignite gasoline vapors.
•
Never fill containers inside a vehicle or on a truck bed with
a plastic bed liner. Always place containers on the ground
away from your vehicle before filling.
•
Remove gas-powered equipment from the truck or trailer
and refuel it on the ground. If this is not possible, then re-
8
•
Tragic accidents can occur if the operator is not alert to
the presence of children and/or bystanders. Never assume
that others will remain where you last saw them.
•
Keep the area of operation clear of all persons, especially
small children and pets. Keep children under the watchful
care of a responsible adult.
•
Be alert and turn the machine off if children enter the area.
•
Before and while moving backwards, look behind and
down for small children.
•
Never allow children to operate the machine
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
Owner’s Manual
CHIPPER SHREDDER
SAFETY DECALS
A
G
B
H
M
C
I
N
D
F
This unit has been designed and manufactured to provide you
with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.
L
Although reading this manual and the safety instructions it
contains will provide you with the necessary basic knowledge
to operate this equipment safely and effectively, we have
placed several safety labels on the unit to remind you of this
important information while you are operating your unit.
E
J
K
O
P
All DANGER, WARNING, CAUTION and instructional messages on your unit should be carefully read and obeyed. Personal bodily injury can result when these instructions are not
followed. The information is for your safety and it is important!
The safety decals below are on your unit.
If any of these decals are lost or damaged, replace them at
once. See your local dealer or contact Earthquake directly for
replacements.
A: Warning!
B:
Read Owner's Manual Before Operating Machine.
C:
Do Not Operate While Others Are Around.
D: Remove Objects that Could Be Thrown By This Machine.
E:
Never Operate Machine Up and Down Slopes, ALWAYS
Operate Mower Across Slopes.
F:
Beware of Moving and Rotating Parts.
These labels are easily applied and will act as a constant visual
reminder to you, and others who may use the equipment,
to follow the safety instructions necessary for safe, effective
operation.
G: Wear Ear and Eye Protection At All Times.
H: Do Not Service or Adjust Moving Parts Unless Engine is
Stopped and Spark Plug Wire is Disconnected.
I:
Direction of Rotating Mower Lines.
J:
Toxic Fumes­—Do Not Operate in Unventilated Areas.
K:
Hot Surfaces.
L:
Fire Hazards.
M. Do Not Use In Thunderstorms--For severe weather, stop
operation of this machine and seek shelter.
N. Team Lift--For your safety, always have at least two people
when lifting this machine.
O. Never Fit Metal Cutting Parts--Do not attach any metal parts
to the cutting head of this machine.
P.
Do Not Operate When Children Or Others Are Around.
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
9
Owner’s Manual
CHIPPER SHREDDER
FEATURES AND CONTROLS
CONTROL FUNCTIONS
The information below briefly describes the function of individual controls. Operating requires the combined use of several
controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the
OPERATION section.
*For engine features and controls see engine manual.
SHREDDER HOPPER
CHIPPER CONE
FUEL CAP
DEBRIS BAG CONNECTOR
KICKSTAND
CHIPPER CONE/SHREDDER HOPPER
Chipper Cone: The chipper cone is located on the front of the unit next to the engine. Insert branches and tree limbs up to
approximately 3” (7.6 cm) in diameter into the chipper cone. NEVER insert hands past the mouth of the cone.
Shredder Hopper: The shredder hopper is on top of the unit. Leaves and other light waste can be loaded into the shredder hopper.
Nothing over 1/2 inch in diameter should go into shredder. NEVER insert hands into the hopper .
Debris Bag: Use the debris bag to collect the material discharged from the unit. Do not operate the unit without the debris bag
in place.
10
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
Owner’s Manual
CHIPPER SHREDDER
SPECIFICATIONS
Model #
18493 / 30520
22752
32013
22754
Chipping Capacity
Approx. 3”
Approx. 3”
Approx. 3”
Approx. 3”
Shredding Capacity
1/2” x 18” long
1/2” x 18” long
1/2” x 18” long
1/2” x 18” long
2
2
2
2
2 J-Hammers,
2 TriangleHammers
2 J-Hammers,
2 TriangleHammers
2 J-Hammers,
2 TriangleHammers
2 J-Hammers,
2 TriangleHammers
Waste Reduction
Ratio
20:1
20:1
20:1
20:1
Start Type
Recoil
Recoil
Recoil
Recoil
Rotor Material
Steel
Steel
Steel
Steel
16.75” x 13.25”
16.75” x 13.25”
16.75” x 13.25”
16.75” x 13.25”
24” x 36”
24”x 36”
24” x 36”
24” x 36”
Limb Chute
Yes
Yes
Yes
Yes
Tire Diameter
11”
11”
11”
11”
Tire Width
2”
2”
2”
2”
Tire Material
Rubber
Rubber
Rubber
Rubber
Wheel Type
Non-pneumatic
Non-pneumatic
Non-pneumatic
Non-pneumatic
Net Weight
121 lb
118 lb
126 lb
119 lb
Gross Weight
131 lb
131 lb
139 lb
129 lb
Assembled
Dimensions
25.4” x 29.9” x 51.9”
25.4” x 29.9” x 51.9”
25.4” x 29.9” x 51.9”
25.4” x 29.9” x 51.9”
Boxed Dimensions
32.2” x 23.9” x 23.1”
32.2” x 24.6” x 24.6”
32.2” x 23.9” x 23.1”
32.2” x 23.9” x 23.1”
Vacuum Kit
Yes
Yes
Yes
Yes
Vacuum
Measurement
20” of Water
20” of Water
20” of Water
20” of Water
Vacuum Air Gate
Yes
Yes
Yes
Yes
Rotor Diameter
14”
14”
14”
14”
Quick Attach
Bag System
Yes
Yes
Yes
Yes
ANSI
Yes
Yes
Yes
Yes
Chipping Knives
Shredding
Hammers
Hopper Dimensions
Bag Dimensions
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
11
Owner’s Manual
CHIPPER SHREDDER
UNPACKING AND ASSEMBLY
G
CARTON CONTENTS
TILLER ASSEMBLY
•
Manual Parts Bag:
•
Hardware Parts Bag:
•
A - (4) M8 x 40 MM Bolts
•
B - (4) M8 x 20 MM Bolts
•
C - (3) M6 x 16 MM Bolts
•
D - (2) 12 x 24 MM Washers
•
E - (12) M8 Washers
•
F - (3) M6 Spring Lock Washers
•
G - (8) M8 Nuts
•
H - (3) M8 Nyloc Nuts
•
I - (3) M6 Nuts
•
Cone Cover
•
Debris Bag
•
Safety Goggles
•
(2) Wheels
•
Hopper
•
Bag Connector
•
Bottle of 4-cycle Engine Oil
•
Cone
•
Chipper Assembly
•
Handlebar
•
Kickstand
•
Hopper Guard
•
Bag Support Rod
WHEEL AXLE
E
A
KICKSTAND
Position the kickstand underneath the engine with the
loop of the kickstand pointing away from the wheel axle.
Using the four M8 x 40 MM bolts (A), eight M8 washers
(E) and four M8 nuts (G), secure the kickstand to the base
plate of the engine.
FIGURE 1
WHEEL AXLE
COTTER PIN
D
Slide the wheel so that the flange on the tire points outward away from the unit, onto the axle and slide a 12 MM
washer (D) onto the axle against it. Insert the a cotter pin
into the hole in the end of the axle. Bend the cotter pin
over to secure the wheel to the axle. Repeat for opposite
side.
FIGURE 2
12
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
Owner’s Manual
CHIPPER SHREDDER
DAMPER
I
STUD PLATE
CHIPPER CONE
H
Position the chipper cone over the three M8 x1.25 threaded
studs protruding from the engine plate, and attach using
three M8 nyloc nuts (H). Rotate cone and cone base away
from engine so cone does not contact engine. Tighten the
three M8 nyloc nuts (H) securely.
Remove back four M6 nuts (I) and set nuts and rear stud
plate aside. Loosen front four M6 nuts (I). Note: These will
not need to removed. Install the damper between the stud
plates as shown.
FIGURE 3
FIGURE 4
HOPPER
I
I
HOPPER GUARD
STUD PLATES
HOPPER
I
F
SLOTTED HOLES
C
Install hopper by sliding slotted holes on the front side of
hopper onto the four studs on the front stud plate with
the previously loosened four M6 nuts (I). Reinstall rear
stud plate and back four M6 nuts (I) that were previously
removed in Figure 4. Tighten all eight M6 nuts (I).
Hold the hopper guard so that the rubber guard is directed
down towards the bottom of the hopper. Align the assembly holes with the holes in the hopper. Using the three M6
x 16 MM bolts (C), three M6 spring lock washers (F) and
three M6 nuts (I), secure the hopper guard to the hopper.
Insert the bolts with washers from the outside of the
hopper.
FIGURE 5
FIGURE 6
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
13
Owner’s Manual
CHIPPER SHREDDER
HOPPER HANDLE
G
E
BRACKET
B
SUPPORT ROD
TAB
Hold the hopper handle up so that the outer holes in the
handle align with the holes in the hopper and secure with
four M8 x 20 MM bolts (B), four M8 washers (E) and four M8
nuts (G). Insert the screws from the outside of the hopper.
Slide the support rod into the bracket. Rotate the rod so
that it sits below the front tab of the bracket.
FIGURE 7
FIGURE 8
TABS
Slide the tabs on the debris bag onto the support rod.
Secure the bag connector onto the chipper by rotating
the connector until locked in.
FIGURE 9
14
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
Owner’s Manual
CHIPPER SHREDDER
OPERATION
DANGER
Be sure to read all information in the Safety and Operation
section before attempting to operate this unit. Become familiar
with all of the controls and how to stop the unit.
THE EXHAUST FROM THIS PRODUCT CONTAINS CARBON
MONOXIDE GAS. CARBON MONOXIDE IS A COLORLESS,
ORDERLESS AND TASTELESS GAS THAT CAN CAUSE
DIZZINESS, NAUSEA, UNCONSCIOUSNESS OR EVEN BRAIN
DAMAGE AND DEATH IF INHALED FOR PROLONGED
PERIODS.
Check all hardware (bolts, screws, etc) before every use for tightness to be sure machine is in safe working condition.
Upon start-up and shut-down, you may hear the metal-tometal sound of the triangular hammers and J-hammers
positioning themselves on the rotor. This is normal. If this
sound continues after the machine has reached full speed,
contact your dealer or Earthquake for an inspection of the unit.
Overloading the equipment will shorten its life, and can cause
mechanical failures.
OPERATE THE UNIT OUTDOORS IN A WELL VENTILATED
LOCATION ONLY. KEEP CHILDREN, PETS AND BYSTANDERS
AWAY.
WARNING
TO AVOID SERIOUS PERSONAL INJURY FROM ROTATING
CUTTING BLADES, KEEP HANDS OUT OF INLET WHILE
MACHINE IS RUNNING.
CHIPPER OPERATION
The chipper is designed to handle tree limbs and branches up
to approximately 3” (7,6 cm) in diameter. The chipping knives
also permit the processing of course organic matter like corn
stalks. Tree branches must be inserted large-end first into the
chipper cone. Since occasional kick-backs may occur, always
stand off to the side of the unit. Allow the self-feeding action
of the unit to draw the sticks in.
GASOLINE IS HIGHLY FLAMMABLE AND MUST BE HANDLED
WITH CARE. NEVER FILL THE TANK WHEN THE ENGINE IS
STILL HOT FROM RECENT OPERATION. DO NOT ALLOW
OPEN FLAME, SMOKING OR MATCHES IN THE AREA. AVOID
OVER-FILLING AND WIPE UP ANY SPILLS.
DO NOT USE GASOLINE CONTAINING METHANOL,
GASOHOL CONTAINING MORE THAN 10% ETHANOL,
GASOLINE ADDITIVES OR WHITE GAS BECAUSE ENGINE/
FUEL SYSTEM DAMAGE COULD RESULT.
SHREDDER OPERATION
The shredder is designed to shred light brush, leaves, and
other soft but bulky organic waste. As material (no larger than
1/2 inch in diameter) is loaded into the shredder hopper it is
pulled into the path of the triangular and J-hammers by air
flow.
IMPORTANT
ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL. YOU
MUST ADD ENGINE OIL BEFORE STARTING ENGINE.
VACUUM ATTACHMENT (OPTIONAL)
In addition to the chipper cone and hopper, loose debris may
be processed by the Vacuum hose adapter kit. Leaves may be
raked directly into the leaf tray where vacuum action will draw
them into the shredder. For hard-to-reach areas, the nozzle
and hose assembly may be used. The strength of the Vacuum
may be changed using the rotating sleeve on the nozzle.
ADDING OIL
Refer to engine manual for information on adding oil.
ADDING FUEL
1.
Remove the fuel cap. (See Features and Controls)
The optional Tazz vacuum kit and can be ordered by
contacting Earthquake customer service or ordering online at
getearthquake.com as listed below.
2.
Fill the tank. Do not overfill. Leave room in the tank for fuel
expansion. Refer to your engine manual for specific fuel
recommendations.
OPERATING LOCATION
3.
Install and hand tighten the fuel cap.
Select an area with firm, level ground, covered by dirt or grass.
Do not operate on wet or slick surfaces, or near bystanders.
Locate and organize the materials to be processed so that you
don’t have to walk in front of the inlet or discharge openings,
and so you have adequate room to work safely.
STARTING THE ENGINE
1.
See engine manual for start up instructions.
2.
Ensure engine is running full throttle before beginning
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
15
Owner’s Manual
CHIPPER SHREDDER
chipping operation. On some engines, the throttle may
not be adjustable.
STOPPING THE ENGINE
See engine manual for shut down procedure.
PROCESSING MATERIALS
Consult the Troubleshooting and Repair section of this
manual, or see your authorized dealer.
•
Maintain control of the materials you are feeding to prevent them from whipping around.
•
Do not insert short pieces of material into the chipper
cone by hand. Use a larger piece of material to feed them
into the chipper cone.
Most materials to be processed can be handled more efficiently by following these tips.
SHREDDING TIPS:
CHIPPING TIPS:
•
Don’t overload the shredder by dumping large volumes of
material into the hopper opening.
•
Alternate loads of wet and dry material to prevent the
discharge from becoming plugged.
•
Never use any object to force material into the shredding
chamber. It could get caught in the shredding hammers
and damage the unit.
•
•
Prune branches down close to the main branch to make
feeding them into the chipper cone easier.
Large, hard, dried tree branches that resist chipping can
be processed by rotating them as you alternately insert
and retract them.
•
If the material to be chipped is extremely hard, kicks back
forcefully when being fed into the chipper cone, or cannot
be easily controlled, remove the material immediately and
set it aside.
•
If additional force is required to insert materials into the
chipper, the blades probably need to be sharpened.
OPERATION
TYPE OF WASTE PERMITTED
SIZE LIMITATIONS
NOTES
Shredding
Dry or moist organic material
including leaves, plants, flowers, fruits, or vegetables.
Branches and twigs up to 1/2”
diameter and 18” long.
Alternately chip or shred moist green
waste with dry waste to avoid plugging of the discharge chute.
Process at a feeding rate that allows
the rotor to keep up and maintain a
high rate of speed.
Chipping
Long, thicker tree limbs or
small bunches of smaller
sticks grouped together for
ease of handling.
Tree limbs and branches,
or bundles of small sticks
grouped for easier handling.
Maximum diameter of approximately 3” (7,6 cm).
Bulky tree limbs should be pruned
close to the main stem. Always use
a shorter piece of wood to push end
pieces into the chipper cone. Never
place hands in the chipper cone.
Never chip very hard or dry materials
such as kiln dried dimensional lumber
(2x4’s etc.) or other building materials.
Never use the chipper to process pressure-treated wood products.
Vacuum Attachment
(Optional Accessory)
Light, loose, dry waste such
as leaves, grass clippings, or
sawdust.
Small materials that will not
obstruct the vacuum hose.
The vacuum is engineered for small,
loose waste and for cleaning around
decorative landscaping and flower
beds. Twigs, wet leaves, and other
bulky materials will clog the hose or
obstruct the shredding chamber.
16
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
Owner’s Manual
CHIPPER SHREDDER
TRANSPORTING AND STORAGE
MAINTENANCE
•
Always observe safe refueling and fuel handling practices
when refueling the unit after transportation or storage.
SCHEDULE AND PROCEDURES
•
Never store the unit (with fuel) in an enclosed poorly
ventilated structure. Fuel vapors can travel to an ignition
source (such as a furnace, water heater, etc.) and cause an
explosion. Fuel vapor is also toxic to humans and animals.
•
Always use the hopper handle and built-in wheels to
move the chipper shredder. Never lift the unit using the
fuel tank for support. If the unit must be lifted , always
use at least two people, and always grip the unit securely
using the front leg and hopper handle.
The following schedule should be followed for normal care of
your unit.
SAFETY ITEMS
BEFORE
EACH
USE
Check for loose
hardware
EVERY
5
HOURS
EVERY
25
HOUR
x
x
Check all safety
labels
x
•
Always follow the engine manual instructions for storage
preparations before storing the unit for both short and
long term periods.
CHIPPER
MAINTENANCE
ITEMS
BEFORE
EACH
USE
•
Always follow the engine manual instructions for proper
start-up procedures when returning the unit to service.
Clean debris from
engine and
chipper. **
x
•
Never store the unit or fuel container inside where there
is an open flame or pilot light, such as in a water heater.
Allow unit to cool before storing.
Inspect/Rotate
Shredding
Hammers
x
STORAGE
Inspect/Rotate
Chipping Knives
x
Perform engine maintenance and storage measures listed in
the engine owner’s manual. This includes draining the fuel
system, or adding stabilizer to the fuel.
**
NOTE: Do not store a fueled unit in an enclosed structure. (See
Gasoline Fires and Handling Fuel Safety)
BEFORE STARTING THE UNIT AFTER IT HAS BEEN STORED:
SPRING
& FALL
EVERY
5
HOURS
EVERY
SPRING
25
& FALL
HOURS
More often in hot (over 85° F: 30° C) weather or dusty
operating conditions.
ENGINE MAINTENANCE
Refer to the engine manual included in your parts packet for
information on engine maintenance. Your engine manual provides information and a maintenance schedule for performing
the following tasks:
1.
Check all fluid levels. Check all maintenance items.
2.
Perform all recommended checks and procedures found
in the engine owner’s manual.
1.
Check oil level before each use or after every 8 hours of
operation.
3.
Allow the engine to warm up for several minutes before
use.
2.
Change oil after first 5-8 hours of operation. Change oil
while engine is warm. Refill with new oil of recommended
grade.
4.
Check spark plug seasonally or every 100 hours of operation.
5.
Service air cleaner.
6.
Keep engine and parts clean.
7.
Check engine and equipment often for loose nuts and
bolts, keep these items tightened.
WARNING
AMPUTATION HAZARD. TO AVOID SERIOUS INJURY FROM
ACCIDENTAL STARTING, ALWAYS DISCONNECT THE SPARK
PLUG WIRE AND SECURE IT AWAY FROM THE SPARK PLUG
WHEN SERVICING THE UNIT.
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
17
Owner’s Manual
CHIPPER SHREDDER
CHECK FOR LOOSE HARDWARE
Service Interval: Every 5 hours; every spring and fall.
Inspect the unit, checking for loose hardware or components.
Pay special attention to the hardware attaching the chipper
cone, hopper, axle, and front leg.
AIR
SHROUD
INTAKE/
AIR FILTER
MUFFLER
DEBRIS OFTEN GATHERS IN
THIS AREA
CHECK SAFETY LABELS
Service Interval: Every spring and fall.
Check that the safety labels are in place and undamaged.
Replace any damaged or missing decals.
INSPECT CONE, HOPPER AND GUARDS
Service Interval: Every spring and fall.
Check that the chipper cone, shredder hopper, and discharge
guards are in place, undamaged, and secure. Replace any
damaged or missing parts.
CLEAN DEBRIS FROM ENGINE AND CHIPPER
Service Interval: Before each use and every 100 hours.
COOLING FINS
FIGURE 10
The engine requires air flow to cool itself and for combustion.
Before each use, clean any debris from the unit especially from
around the air shroud intake, air filter, and muffler. Every 100
hours, remove the engine air shroud and clean out any debris
from the engine cooling fins SEE FIGURE 10. We recommend
having this service performed by an authorized repair center.
INSPECT / ROTATE SHREDDING HAMMERS
Service Interval: Every 25 Hours, or As Necessary
The shredding hammers of this unit can be rotated to provide
a new cutting surface as required. The triangular hammers
can be rotated twice, then flipped over for a total of 6 sharp
cutting surfaces. The J-hammers can be flipped over once. To
inspect the shredding hammers:
1.
Disconnect the spark plug wire and secure it away from
the spark plug. SEE FIGURE 14 (on page 19).
2.
Remove the small circular access panel (B) from the back
of the shredder housing. SEE FIGURE 11.
3.
Inspect the cutting edges of the triangular hammers (A)
and J-hammers (A). SEE FIGURES 11 AND 12.
ACCESS PANEL
J-HAMMER
WEAR AREA
FIGURE 11
TRIANGULAR-HAMMER
WEAR AREA
To rotate or replace the shredding hammers, see the Troubleshooting and Repair section.
FIGURE 12
18
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
Owner’s Manual
CHIPPER SHREDDER
INSPECT CHIPPING KNIVES
Service Interval: Every 25 hours, or as necessary
CAUTION
The chipping knives of this unit can be rotated or sharpened
to provide a new cutting surface as required. When inspecting the knives be careful to avoid touching the sharpened
edges. To inspect the chipping knives:
FOR THE SAFETY OF THE USER, AND TO MAXIMIZE THE
LIFE OF THE ENGINE, IT IS CRUCIAL TO TAKE TIME TO
CHECK THE CONDITION OF THE ENGINE. PROBLEMS MUST
BE CORRECTED BEFORE OPERATING.
1.
Disconnect the spark plug wire and secure it away from
the spark plug. SEE FIGURE 14.
2.
Remove the nuts securing the chipper cone to the front
of the chipper. Remove the chipper cone (A) to access the
knives. SEE FIGURE 13.
AVOID INJURY! ENGINE OIL IS HAZARDOUS TO YOUR
HEALTH. DISPOSE OF OIL APPROPRIATELY. USE A SAFE
DISPOSAL/RECYCLING CENTER.
3.
Using the recoil starter, slowly pull the starter rope to
rotate the rotor into position so the blades can be seen.
CHIPPER CONE
To sharpen or replace the chipper knives, see the Troubleshooting and Repair section.
CHECK / CHANGE ENGINE AIR CLEANER
Service Interval: Every 25 hours
The engine air cleaner assembly should be opened, inspected,
and the filter element replaced every 25 hours, or as required if
debris has built up in the assembly.
FIGURE 13
To replace the air filter, see engine manual.
REPLACE SPARK PLUG
Please contact your authorized repair center to perform
this service.
SPARK PLUG
OIL MAINTENANCE
Refer to engine manual for oil maintenance.
FIGURE 14
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
19
Owner’s Manual
CHIPPER SHREDDER
TROUBLESHOOTING
While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually
require that service be performed to allow it to continue operating properly.
The troubleshooting guide below lists the most common problems, their causes, and remedies.
See the information on the following pages for instructions on how to perform most of these minor adjustments and service
repairs yourself or by your local authorized repair center.
CAUSE
PROBLEM
Engine will not start.
REMEDY
1.
Out of fuel.
1.
Add Fuel.
2.
Spark plug wire disconnected.
2.
3.
Engine controls not set correctly.
Reconnect spark plug wire as recommended in engine manual.
4.
Spark plug fouled.
3.
Refer to STARTING in the engine manual.
5.
No compression. Recoil starter pulls
with no resistance.
4.
Remove spark plug. Clean/replace as
recommended in engine manual.
6.
No spark. Ignition problems.
5.
See your authorized service center.
7.
Old or stale fuel.
6.
See your authorized service center.
7.
See your authorized service center.
1.
Dirty air filter
1.
Replace air filter. See engine manual.
2.
Choke closed.
2.
Open choke.
Engine runs but no material is
discharged.
1.
Discharge chute clogged.
1.
Clean out debris.
2.
Engine not running at full speed.
2.
Set throttle control to FAST if equipped.
For fixed throttle engines see your
authorized service center.
Excessive branch vibration
when chipping materials.
1.
Chipper knives dull.
1.
Sharpen/Replace chipper knives.
2.
Tree limbs are extremely hard or dried
out.
2.
Material is not suitable for chipping.
Unusual noise or vibration
when chipping materials.
1.
Rotor overloaded with material.
1.
2.
Hammers are broken, bent, or loose.
Allow unit to clear itself before adding
more material to the hopper.
3.
Hammers frozen in place.
2.
Check assembly. Tighten or replace as
necessary.
3.
Check for obstructions and debris. Repair
or replace as necessary.
Engine exhaust is black.
Vacuum not working.
20
1.
Hopper gate not closed.
1.
Slide gate to closed position.
2.
Cone cover not installed.
2.
Allow material to dry.
3.
Hose not attached properly.
3.
4.
Hose obstructed or damaged.
Attach hose per instructions (See Hose
Kit).
5.
Engine not running at full RPM.
4.
Clear blockage or replace.
5.
Set throttle control to FAST if equipped.
For fixed throttle engines see your
authorized service center.
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
Owner’s Manual
CHIPPER SHREDDER
REPAIR
WARNING
ROTOR REMOVAL
NOTE: The rotor does not need to be removed to change the
hammers and knives. However, the removal and installation of the knives will be easier with the rotor removed.
CUTTING HAZARD. TO AVOID SERIOUS INJURY, AVOID
CONTACTING THE SHARP CUTTING EDGES OF THE
CHIPPING KNIVES.
NOTE: If using a unit that has socket head bolts with no locking plates on them, the hardware will need to be upgraded to
new hardware kit.
To remove the rotor from the drive shaft:
1.
Turn the engine off and wait for all moving parts to stop.
2.
Disconnect the spark plug wire and secure it away from
the spark plug. SEE FIGURE 15.
3.
Detach the rotor housing and hopper from the rotor
plate. SEE FIGURE 16.
4.
Bend the side tabs away from the center mounting bolt
and remove the bolt (8).
5.
Carefully remove the rotor plate, spacer, and key (10) from
the crankshaft. SEE FIGURE 17.
SPARK
PLUG
WIRE
FIGURE 15
HAMMER REMOVAL AND INSTALLATION
NOTE: The cutting edges of the shredding hammers may eventually wear out requiring rotation of the hammer or replacement if all cutting edges have been dulled.
ROTOR PLATE
ROTOR HOUSING
FIGURE 16
NOTE: Triangular hammers can be rotated twice after the first edge dulls, then flipped over once and rotated again for a total of six edges. J-hammers can be flipped over
once for a total of two cutting edges.
1.
Remove the hammers by first bending the lock plate
tabs down away from the hex head bolt securing the
hammers. Remove the bolt. SEE FIGURES 18 AND 19
(next page).
NOTE: the assembly sequence of the hardware used to secure the hammers.
2.
Inspect the hammers, spacers, and hardware. If the spacer
tube shows signs of wear, replace it. Inspect and flip, or
replace the hammers. The lock plate should always be
replaced when replacing or rotating hammers.
3.
Inspect the hammers, spacers, lock plate and bolts. Torque
the bolt to 30-35 ft -lb (41-47 N.m.). The J-hammer on the
3/8 X 2” BOLT
KEY
SPACER
ROTOR PLATE
FIGURE 17
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
21
Owner’s Manual
CHIPPER SHREDDER
opposite side of the rotor faces outward for balanced rotation. Two faces of the bolt should align in parallel with the
lock plate tabs.
NOTE: We recommend the use of high-strength thread
locker on mounting bolts.
4.
5.
Bend the lock plate tabs up to secure the bolt and preventing rotation. The tabs should sit flat on a face of the
bolt. SEE FIGURE 18.
LOCK PLATE
TABS
Repeat for all hammers.
FIGURE 18
CHIPPING KNIFE REMOVAL AND INSTALLATION
ROTOR PLATE
To inspect or replace the chipping knives:
1.
Bend the lock plate tabs away from the bolts securing the
chipping knives.
2.
Remove the two bolts and the chipping knife. SEE
FIGURE 20.
3.
Inspect or replace the chipper knife.
4.
Reinstall the chipper knife and tighten the bolts to 18-20
ft-lb (24-27 N.m.). Ensure that the knife is sitting squarely
against the stop that has been formed into the rotor. If it is
not sitting square, the knives will perform as if they are extremely dully. Always use a new lock plate when installing
knives. Two of the bolt faces should align in parallel with
the lock plate tabs.
TRIANGULAR-HAMMER
M10 X 50 MM
BOLT
LOCK
PLATE
SPACERS
J-HAMMER
FIGURE19
LOCK
PLATE
Note: We recommend the use of high-strength thread locker
on mounting bolts.
5.
Bend the lock plate tabs up to prevent bolt rotation. The
tabs should sit flat on a face of the bolt. SEE FIGURE 18.
KNIFE
M8 X 16 MM
BOLT
INSTALL THE ROTOR ON THE CRANKSHAFT
To install the rotor on the crankshaft:
1.
Replace the rotor onto the crankshaft, careful to replace
the spacer and key. SEE FIGURE 17.
2.
Torque the mounting bolt to 30-35 ft-lb (41-47 N.m.).
3.
Bend the lock plate tabs up to secure the mount bolt and
prevent rotation. The tabs should sit flat on the face of the
bolt.
4.
Reinstall rotor housing and hopper. SEE FIGURE 16.
22
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
ROTOR PLATE
FIGURE 20
Owner’s Manual
CHIPPER SHREDDER
NOTES:
Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST
23
ARDISAM, INC.
1160 Eighth Avenue
PO Box 755
Cumberland, WI 54829
Phone: (800) 345-6007
Fax: (715) 822-2124
www.GetEarthquake.com
">