RTS Ps-15 Manual
Add to My manuals13 Pages
The RTS WM300 is a professional wireless microphone system that offers reliable and versatile audio transmission for various applications. With its advanced features, it provides exceptional sound quality and flexibility for both indoor and outdoor events. The system includes a bodypack transmitter, a handheld microphone or a headset microphone, and a receiver. It operates in the 2.4GHz frequency range, ensuring interference-free performance even in crowded RF environments.
advertisement
Model PS-15
Power Supply
9350678600 Rev H 11/2006
PROPRIETARY NOTICE
The product information and design disclosed herein were originated by and are the property of Telex Communications, Inc. Telex reserves all patent, proprietary design, manufacturing, reproduction, use and sales rights thereto, and to any article disclosed therein, except to the extent rights are expressly granted to others.
C OPYRIGHT N OTICE
Copyright 2006 by Telex Communications, Inc. All rights reserved.
Reproduction, in whole or in part, without prior written permission from
Telex is prohibited.
W ARRANTY N OTICE
See the enclosed warranty card for further details.
C USTOMER S UPPORT
Technical questions should be directed to:
Customer Service Department
RTS/Telex Communications, Inc.
12000 Portland Avenue South
Burnsville, MN 55337 USA
Telephone: 800-392-3497
Fax: 800-323-0498
S HIPPING TO THE M ANUFACTURER
All shipments of product should be made via UPS Ground, prepaid (you may request from Factory Service a different shipment method). Any shipment upgrades will be paid by the customer. The equipment should be shipped in the original packing carton. If the original carton is not available, use any suitable container that is rigid and of adequate size. If a substitute container is used, the equipment should be wrapped in paper and surrounded with at least four (4) inches of excelsior or similar shock-absorbing material. All shipments must be sent to the following address and must include the Proof of Purchase for warranty repair.
Upon completion of any repair the equipment will be returned via
United Parcel Service or specified shipper, collect.
Factory Service Department
Telex Communications, Inc.
8601 East Cornhusker Hwy.
Lincoln, NE 68507 U.S.A.
Attn: Service
This package should include the following:
R ETURN S HIPPING I NSTRUCTIONS
Customer Service Department
Telex Communications, Inc. (Lincoln, NE)
Telephone: 402-467-5321
Fax: 402-467-3279
Factory Service: 800-553-5992
Please include a note in the box which supplies the company name, address, phone number, a person to contact regarding the repair, the type and quantity of equipment, a description of the problem and the serial number(s).
TABLE OF CONTENTS
PROPRIETARYNOTICE
COPYRIGHTNOTICE
PATENTNOTICE
UNPACKINGANDINSPECTION
WARRANTYThWORMATION..
,
RETURNSHWPINGINSTRUCTIONS
SECTION 1: DESCRIPTION & SPECIFICATIONS
1.1 DESCRIPTION.
1.2MODELPS15SPECIFICATIONS
SECTION 2: INST ALLA TION
2.1MECHANICALINSTALLATION
2.2 OUTPUTS.
2.3POWERANDINPUTPOWERSELECTION
2.4ELEC1RICALPERFORMANCEANDLOADING
2.5TANDEMOPERATION
2.6AUDIOOUTPUT/INPUT
2.7STANDARDUSERSTATIONCONNECTIONS
SECTION 3: OPERA TION
SECTION7:DIAGRAMS
,...
,
5
5
5
4
4
6
5
5
5
9
7
2
2
2
2
2
2
4
8
Page 3
SECTION I:
DESCRIPTION AND SPEClFICA TIONS
1.1 DESCRIJYrION
The Model PS 15 Power Supply is designed to work within the TW Intercom System. The PS 15 is suitable for small to medium sized TW Intercom Systems.
The unit is self-contained and features two-channel operntion: one "wet" channel with 24 to 32 volts DC and one
"dry" channel without voltage potential. Each channel provides an audio termination impedance of 200 or 400 ohms (switch selectable).
This power supply allows speech signals and DC to exist on the same wire (Channel I). The power supply's outputs are protected against short circuit conditions with recovery being automatic and instantaneous.
A single PS 15 Power Supply can power 6 to 30 user stations
(depending on model and combination -see specifications).
If still more user stations are needed, two PS 15 Power
Supplies can be coupled together to double the powering capability: a 1/4-inch 3-circuit phone jack is available on each power supply for this purpose. This connector can also be used as a one-way output port when monitoring or recording the intercom audio signals.
When two PS15 supplies are combined. toggling a rear pmlel switch on each supply will keep the audio level constallt. Two PS 15. s can power as many stations as a PS31
(with DC load evenly distributed between the two supplies).
Since the PS31 supplies more voltage than the PS15 under full load. the PS31 is better suited to power a large system spread over a large area.
There are two XLR-type 3-pin male connectors mounted on the rear panel for output interconnection to the user stations.
The PS 15 has been designed to meet UL 1419 specifications
(professional Audio and Video Equipment).
The PSIS Power Supply may be used in portable applications (use optional MCP8 channels) or in standard EIA equipment racks (use optional MCPl or MCP2 rack mounting kits).
The PS 15 is one rack unit high and one-half rack wide. A single PS 15 may be rack -mounted singly or two PS 15. s may be mounted side-by-side.
1.2 MODEL PSIS SPECIFICATIONS
Outputs
One powered channel, CHI, (audio + DC + 200 ohm/400 ohm 10% termination}, and one passive channel' CH2, (audio + 200/400 ohm 20% termination}.
Output Voltage
No Load
Full Load
32.0 +2.0. -1.0 volts
24.0 volts. nominal
Output Impedance
200 or 400 ohms 20%. switchable. On powered channel. 200 ohms. nominal. is maintained from 18.0
to 33.0 volts.
Output Current
S13nd'Jfd Option
*p Option (234 V)
#D Option (IOOV)
Fault Current
.9 ampere at 21/+4-2 volts. DC
.9 ampere at 21/+4-2 volts. DC
.8 ampere at 21/+4-2 volts. DC
1.5 amperes at 0.0 volts. DC
Signal Level
Nominal
Maximum
2.0 volts peak to peak
5.0 volts peak to peak
Frequency Response
100 hertz to 20 kilohertz +1, -5 dB
Signal-to-Noise Ratio
Reference 2.0 volts. peak to peak: 60 dB nomina]
Mains Voltage
Standard
*POption
#D Option
117 volts :t10%. 50 -60 hertz
234 volts :t10% 50-60 hertz
100 volts +10%. -5%.50-60 hertz
Mains Amperes
0.40 at 117 volts :t10%, 50-60 hertz
0.20 at 234 volts :t10%, 50-60 hertz
0.40 at 100 volts +10%, -5%,50-60 hertz
Environmental
Temperature
Operating 00 to 50°C
-40° to 70°C
0 to 95(.70, non-condensing
Humidity
Dimensions
Height
Width
Depth
1.72 inches (44 millimeters)
8.186 inches (207.9 millimeters)
8.33 inches (211.6 millimeters)
Weight
PSl5
MCPl
MCP2
4.29 pounds (1.95 kilograms)
1.0 pounds (0.454 kilograms)
1.0 pounds (0.454 kilograms)
Finish
Thennoplastic front panel. aluminum case. light gray finish
Page 4
SECTION 2: INSTALLATION
2.1 MECIIANICAL INSTALLATION
at 800 milliamperes when connected in series, but with
100 volts at the primaries the output voltage is 26 volts.
The Model PSl5 can be installed in 3 ways: a single unit mounted in a half rack space using an optional Modcl
MCP2 Kit for rack mounting a single unit; or two PSl5 supplies mounted side by side using the optional MCPl
Kit for rack mounting two units side by sidc; or frce standing using the optional MCP8 Kit for adding side channels for non-rack mounting portable 1,Ise.
Note: The European version of the Model PSIS is equipped with a special three conductor European power cord / plug set. The plug is the a CEE7n style rated for
234 volt /10 to 16 ampere service. The European version is also equipped with a metric fuse holder and an internationaJ S by 20 millimeter fu~.
2.4 ELEcrRICAL PERFORMANCE AND LOADING
2.2 OUTPUTS
Located on the back panel are the outputs. The PS15 is designed to accept A3F 3-pin female connectors.
2.3 POWER and INPUT POWER SELECTION
The power cord is attached to the rear panel. Power selection is normally done at the factory. If field change of the input mains voltage is required, disconnect the power, open the case, and set jumpers as follows (using layout diagram on page 10):
The first table on the next page shows operating distances versus model numbers for the PS15 power supply. The second table on the next page shows the maximum number of user stations that the PS15 can sustain. For combinations of stations, multiply the current values in the first table times the number of units of that type. The sum of all the currents should be less than 1 ampere for the PS15.
2.5 TANDEM OPERATION
For 117 V AC operation, T1 is Signal Transformer
LP56-425 or equivalent; install W1, W2, W4, and W6, remove W3 and W5. * (Standard-American ]
For 234 V AC operation, T1 is Signal Transformer
LP56-425 or equivalent; install W3, W4, and W6, remove W1, W2, and W5. * [*P Option-European]
For 100 V AC operation, TI is Signal Transformer
LP30-800 or equivalent: install Wl, W2, and W5, remove W3, W4, and W6. ** [#D Option-Japanese)
Two Model PS 15 power supplies can be used in tandem to double the number of stations that can be powered. First, the stations are divided between the supplies. Then, a stereo patch cord is plugged into the stereo jack on the rear panel of each supply. The DUAL/NORMAL switch is set to DUAL. This switch corrects the halving of the impedance of two supplies in parallel by doubling the impedance of each supply from 200 to 400 ohms. The line signal levels are maintained because the net impedance is now 200 ohms.
The fuse must aJso be changed to the rating shown on the rear panel.
2.6 AUDIO OUTPUT I INPUT
.Transformer LP56-425 is a dual primary, dual secondary transformer. The primaries are 115 volts each. The two secondaries are rated 28 volts at 850 milliamperes when connected in parallel. For 115 volt operation, the primaries are in parallel, and the secondaries are in parallel. For 230 volt operation, the primaries are in series, and the secondaries are in parallel.
..Transformer LP30-800 is a dual primary, dual secondary transformer. The primaries are normally rated
115 volts each, but jn this case will be operated at 100 volts each. The secondaries are normally rated at 30 volts
The AUDIO COUPLING CHI-CH2 jack on the rear panel provides an unbuffered, unbalanced audio output for each of the two channels. The level ranges from
-10 dBu to 0 dBu. An isolation transformer is recommended to prevent a ground loop between the intercom system common and other grounds.
The AUDIO COUPLING jack may also be used to input a signal into the system. Use at least a 2.2 kilohm resistor in series with the signal source to prevent loading of the RTS
Systems intercom line. Use an audio isolation tranformer to prevent ground loops.
Page 5
The table bclow lists maximum orcrating distanccs of a PS15 powcr supply vs. user station model # .Assumptions: 22 gage wire, stations orcrating with 250 hcadphonc load, 10 dB bclow clipping.
Model # Quantity Itot (milliamperes) Distance (rcct) Distance (meters)
BP300
II
BP300L
BP317
BP320
BP320L
BP325(St)
BP325SM ..(St)
SPK300
1
1
1
1
1
1
1
1 fill n
~
.Q1
~
@
1QQ
SPK300L
ill
..Surface mount version. (St) means stereo configuration.
5024
3098
5024
4131
2774
2323
3098
1859
1487
1531
944
1531
1259
846
708
944
567
453
The table below lists maximum number of stations versus User Station Type & Model Number (using a PS8 or PS15 power supply). The PS8 rated current is 430 milliamperes, the PS15 rated current js 1000 milliamperes.
Station Type
Belt Pack, Headset
Belt Pack, Headset, CalI Light
Belt Pack, Headset, Single Channel
Model
BP300
BP300L
BP317
Qty PSB Qty PS15
II
7
11
27
16
27
Belt Pack, Headset, Stereo
Belt Pack, Headset, Stereo, Call Light
BP320
BP320L
9
6
22
15
Belt Pack, Headset, Stereo, Call Light, Microprocessor BP325(St)
Belt Pack, Headset, Stereo, Call Light, Microprocessor, Surface Mount BP325(St)
Speaker, Portable .
SPK300
Speaker, Portable, Call Light **
SPK300L
5
7
4
3
11
16
10
8
Note: Capacity can be increased by using two power supplies, splitting the load between the two supplies, interconnecting the supplies audio only, and by switching the power supply impedance switches from NORMal to
DUAL. .Also valid for RMS300. ..Also valid for RMS300L. WM300, CM300 similar to BP300. WMS300 similar to SPK300. (St) Means Stereo configuration.
Page 6
SEcrlON 3: OPERATING INSTRUcrlONS
Figure 3-1
Model PS15 Front Panel
Figure 3.2
Model PSIS Rear Panel
Page 7
SECTION 7: DIAGRAMS / DRA WINGS
Document
Number ~ Ii1le.
OD2368
SD6759 B
B
A
A
PSIS Block Diagram
Outline Drawing, Model PS 15 Power Supply
Layout, Printed Circuit Assembly, (PCA), Model PS 15 Power Supply
Schematic Diagram. Model PS 15 Power Supply. Sheet 1 of 1
Installation Illustration -MCP Components
~
11
12
8
9
10
PSIS Block Diagram
Page 8
! I ~I~
Ii ~I
~ tIr
!
Nr::r-.
.I')
~.!-
.
1r'1""'i' r'1~ cxiE
0';;;'
~O
,..:~
~
.N.
t--O
~
.
OD2368
Outline Drawing,
Model PS15 Power Supply
U)
ID
-.J
01
N
..t
~
01
1!)
~
~
'--"
.:.:
I
<:>
W
3:
(n
"""
~
(n
~
"'
~I ffi I w z
::i f-
:)
0
(!) z
~
0::
0
~
0-
0-
:) tn
In
I
U) a-
(I:: w
3 o
0-
--1
LLJ o
O
L
Jill
N
I"...
~ a::: 1~~I~j
I 9 I ';0
I w
~I ,
.illr
N
1 '
5
" , oi ,,"""
~r--
00
OO~
.
C::j
O l
~
Vi z o
Vi z
4)
~
O
-J
-J
«
E
E
'--'
(/)
4)
I u
~
Page 9
Layout, Printed Circuit
Assembly, Model PSIS
Power Supply
Page 10
~ rMPEDANCE SELECT
(REAR PANEL)
0'4
'N523'e
5.'V
0'5
'N523'B
5.'V
5
VOLTAGES INDICATED BY TEST POINTS HAVE 2~ TO!..ERANCE.
TOP VALUE IS NO LOAD CONDITION. BOTTOM VALUE IS
FULL LOAD (1 AMP) CONDITION. VOLTAGES APPLY TO INPUT
VOLTAGES SHOWN.
G FOR 1OOVAC
INSTALL W1.W2 AND WS.
USE TRANSFORMER (11SVX2.1SVX2.24VA)
FOR 117VAC OPERATION:
INSTALL W1.W2.W4 AND W6.
USE TRANSFORMER (11SVX2.28VX2.24VA)
FOR 234VAC OPERATION:
INSTALL W3.W4 AND W6.
USE TRANSFORMER (11SVX2.28VX2.24VA)
RTSlf23O1-OO27-OO.
RTSII23O1-OO26-OO.
RTSlf23O1-OO26-OO.
~ THERMAL
LOCATED
BREAKER 95 DEGREES CELS~US
BETWEEN T1 AND T2.
OPEN~NG TEMPERATURE
2. CAPACrTANCE VALUES SHOWN: MrCROFARADS/VOLTS.
,. ALL RESrSTORS ARE rN OHMS. ,/4- WATT. CARBON FrLM. +-5~.
NOTES: UNLESS OTHERWISE SPECIFIED Page 11
NOT USED: 013
LAST USED: 017 .D2O.F"1.J1.P3.R27 .52. T2. TP7 .W7.U1.DS1
I CONTRACT No.1
IRTS iD'.own
I R.NErLsoN
c:necked
SYSTEMS Bu'.bank.
---
Callfa'.nla
SCHEMATrC DrAGRAM. TW POWER SUPPLY.
MODEL PS15
J:ssued
SIZE DWG NO
-..,-,1
~
U
1 Ii
D PS15
~
U
III
PS15
[';I
~
110
PS15
II
[
I
D
I n II
J
WITH MCP8
PS15
II
1;] o SINGLE MOUNT
0 WITH MCP2
[
I I n
PS15
II
I I n II
])
o DUAL MOUNT o WITH MCP1
PS15
=
II
=
I fffffi(f).
(f) .O 0 o 011
MRT327
]] o DUAL o WITH MCP 1
AND MRT327
I a!E~.~.0.@II'
(() .: ..0.
~
MCE325
@ D o DUAL o WITH MCP 1
AND MCE325
Installation Illustration'---MCP Components
Page 12
advertisement
Related manuals
advertisement