Wattstopper
®
Digital Lighting Management Plug Load Controller
No: 24045 – 01/19 rev. 3
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
Catalog Number • Numéro de Catalogue • Número de Catálogo: LMPL-101
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
LMPL-101-U is BAA and TAA compliant (Product produced in the U.S.)
SPECIFICATIONS
Input Voltage............................................................................... 120VAC, 50/60Hz
Output Capacity............................................................................. 150mA@24VDC
Power Supply............................................................ Wattstopper Room Controller
Connection to the DLM Local Network............................................... 3 RJ-45 ports
DLM Local Network characteristics when using LMRC‑11x/2xx room controllers:
Low voltage power provided over Cat 5e cable (LMRJ); max current 800mA.
Supports up to 64 load addresses, 24 communicating devices including up
to 4 LMRC‑10x series and/or LMPL‑101 controllers.
Free topology up to 1,000’ max.
Environment............................................................................ For Indoor Use Only
Operating Temperature............................................32° to 131°F (0° to 55°C)
Storage Temperature............................................. 23° to 176°F (-5° to 80°C)
Relative Humidity..................................................5 to 95% (non condensing)
Patent Pending
This unit is pre-set for Plug n’ Go™ operation, adjustment is optional.
For full operational details, adjustment and more features of the product, see the DLM System Installation Guide provided with Wattstopper room
controllers, and also available at www.legrand.us/Wattstopper.
Installation shall be in accordance with all applicable regulations, local and NEC codes. Wire connections shall be rated suitable for the wire size
(lead and building wiring) employed.
For Class 2 DLM devices and device wiring: To be connected to a Class 2 power source only. Do not reclassify and install as Class 1, or Power and
Lighting Wiring.
PLACEMENT EXAMPLES
Line Voltage
(Class 1 wiring)
Line Voltage
(Class 1 wiring)
Line Voltage
(Class 1 wiring)
Plug Load
Controller
J-Box
Plug Load
Controller
J-Box
To Plug Load
(Class 1 wiring)
To Plug Load
(Class 1 wiring)
Room
Controller
J-Box
To Lighting
Load
(Class 1 wiring)
Switch
To Other
Electrical
Outlets
Ceiling Mount
Occupancy
Sensor
Switch
To Other
Electrical
Outlets
Ceiling Mount
Occupancy
Sensor
MOUNTING THE CONTROLLER
ATTACHING CABLES
Li
Li
ne
ne
Load
Load
J-Box
J-Boxes
Inside a 4" x 4" box
Outside a 4" x 4" box
WARNING: TURN THE POWER OFF AT THE
CIRCUIT BREAKER BEFORE WIRING.
Remove rubber jack covers if using all 3 RJ45 receptacles.
Leave covers in place for all unused receptacles.
CONNECTIVITY
The LMPL-101 communicates with all other DLM devices connected to the DLM local network. Connection drawings are for example
only. The low voltage LMRJ cables can connect to any DLM device with an open RJ45 receptacle.
All line voltage wiring is #12 AWG.
CAUTION: TO CONNECT A COMPUTER TO THE DLM LOCAL NETWORK USE THE LMCI‑100.
NEVER CONNECT THE DLM LOCAL NETWORK TO AN ETHERNET PORT – IT MAY
DAMAGE COMPUTERS AND OTHER CONNECTED EQUIPMENT.
Line
Voltage
Low Voltage
DLM Local Network
LMRJ Cables
Room
Controller
Ceiling Mount
Sensor
LMRC
102
J-Box
Switch
Plug Load
Controller
Loads
Red to
Load 1 (A)
1
Yellow to
Load 2 (B)
2
120VAC
White: Neutral
J-Box
LMPL-101
Ground
Red: Switched
120VAC Line
PLUG N’ GO OPERATION (PNG)
Load ON/OFF button
The plug load circuit connected to the LMPL-101 is automatically controlled by all
occupancy sensors on the DLM local network. After the last occupancy sensor’s time
Blue LED ON when
delay expires, or when a switch button bound to the LMPL-100 is operated, the LMPL-101 load is ON
shuts off the plug load circuit.
UNIT ADJUSTMENT - PUSH N’ LEARN
Load Selection Procedure
Before testing or adjusting the DLM local network load configuration, plug a lamp or radio into one of the electrical outlets on the
controlled plug load circuit.
A configuration button (Config) allows access to our patented Push n’ Learn™ technology to change binding
relationships between sensors, switches and loads.
Step 1 Enter Push n’ Learn.
Press and hold the Config button (on any DLM device) for 3 seconds.
The red LED on the LMPL-101 begins to blink faster (2x per second) as does the red LED on ALL other
communicating devices connected to the DLM local network.
The red LEDs continue to blink until you exit PnL mode.
2
Config button & red LED
All loads in the room turn OFF immediately after entering PnL, then one load will turn ON. This is Load #1, which is bound to switch
button #1 and occupancy sensors as part of the Plug n’ Go factory default setting. All switch buttons and sensors that are bound to
this load have their blue LED solid ON.
Step 2 Load selection.
Press and release the Config button to step through the loads connected to the DLM local network. As each load turns ON note the
devices (switch buttons and sensors) that are showing a bright solid blue LED. These devices are currently bound to the load that is ON.
The blue LED on the room controller or plug load controller connected to the load is also lit.
• To unbind a switch button from a load, press the switch button while its blue LED is ON bright. The blue LED goes dim to indicate
the button no longer controls the load that is currently ON.
• To unbind an occupancy sensor, press the up () or down () adjustment button while its blue LED is ON. The blue LED turns
OFF to indicate the sensor no longer controls the load that is currently ON.
• Pressing the switch or up () or down () button again while the load is ON rebinds the load to the button or sensor and the blue
LED illuminates brightly.
Step 3 Exit Push n’ Learn.
Press and hold the Config button until the red LED turns OFF, approximately 3 seconds.
TROUBLESHOOTING
Loads do not operate as expected.
LEDs on a switch or sensor
don’t light.
1. Check to see that the the device is connected to the DLM local network.
2. Check for 24VDC input to the device: Plug in a different DLM device at the device location.
If the device does not power up, 24VDC is not present:
• Check the high voltage connections to the plug load controller.
• If high voltage connections are good and high voltage is present, recheck DLM local network
connections between the device and the plug load controller.
The wrong lights and plug
loads are controlled.
1. Configure the switch buttons and sensors to control the desired loads using the Push n’ Learn
adjustment procedure.
LEDs turn ON and OFF, but
load doesn’t switch.
1. Make sure device is not in PnL.
2. Check load connections to room controllers and/or plug load controllers.
3
WARRANTY INFORMATION
INFORMATIONS RELATIVES À LA GARANTIE
INFORMACIÓN DE LA GARANTÍA
Wattstopper warranties its products to be free
of defects in materials and workmanship for a
period of five (5) years. There are no obligations
or liabilities on the part of Wattstopper for
consequential damages arising out of, or in
connection with, the use or performance of this
product or other indirect damages with respect
to loss of property, revenue or profit, or cost of
removal, installation or reinstallation.
Wattstopper garantit que ses produits sont
exempts de défauts de matériaux et de fabrication
pour une période de cinq (5) ans. Wattstopper
ne peut être tenu responsable de tout dommage
consécutif causé par ou lié à l’utilisation ou
à la performance de ce produit ou tout autre
dommage indirect lié à la perte de propriété, de
revenus, ou de profits, ou aux coûts d’enlèvement,
d’installation ou de réinstallation.
Wattstopper garantiza que sus productos
están libres de defectos en materiales y mano
de obra por un período de cinco (5) años. No
existen obligaciones ni responsabilidades por
parte de Wattstopper por daños consecuentes
que se deriven o estén relacionados con el
uso o el rendimiento de este producto u otros
daños indirectos con respecto a la pérdida
de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
No. 24045 – 01/19 rev. 3
© Copyright 2019 Legrand All Rights Reserved.
© Copyright 2019 Tous droits réservés Legrand.
© Copyright 2019 Legrand Todos los derechos reservados.
800.879.8585
www.legrand.us/wattstopper
">
