Silicon Labs C8051T620/2-DK Quick Start Guide

C8 0 5 1 T6 2 0 / 2 - DK
The C8051T620 and C8051T622 Development Kits contain the following items:
C8051T62x
Motherboard
C8051T62x Emulation Daughter Board with C8051F34A installed
Socket Daughter Board (one of the following):
C8051T620DK:
C8051T622DK:
samples (one of the following):
C8051T620DK:
C8051T622DK:
C8051Txxx
C8051T620-GM (Qty: 10) and C8051T626-B-GM (Qty: 10)
C8051T622-GM (Qty: 10)
Development Kit Quick-Start Guide
Start Guide includes steps to download the following development software and documentation (these
instructions can also be found in this document. See “4. Software Installation” on page 3.):
• Silicon Laboratories Integrated Development Environment (IDE)
• Evaluation version of 8051 development tools (macro assembler, linker, C compiler)
• Source code examples and register definition files
• Documentation
AC-to-DC
Two
universal power adapter
USB cables
fo
r
Quick
N
ew
Device
C8051T62x QFN 32-pin
C8051T622 QFN 24-pin
D
1. Kit Contents
es
ig
ns
C8051T620/2 D E V E L O P M E N T K I T U SER ’ S G UIDE
m
en
de
d
2. About the Daughter Boards
The C8051T620 and C8051T622 Development Kits include an Emulation Daughter Board (EDB) and a QFN
Socket Daughter Board (QFN-DB). The EDB has an installed C8051F34A device, which is a Flash-based device
that can be used for the majority of C8051T62x/32x code development. The QFN-DB is intended to allow both
programming and system-level debugging of C8051T62x/32x devices directly.
N
ot
R
ec
om
A C8051T62x/32x device cannot be erased once it has been programmed; so, it is advisable to use the
C8051F34A for the majority of code development. Refer to “AN368: Differences between the C8051F34A and the
C8051T62x and C8051T32x Device Families” for more details on how the C8051F34A can be used to develop
code for the C8051T62x/32x device families. Application notes can be found on the Silicon Labs web site:
www.silabs.com/appnotes
Rev. 0.5 7/12
Copyright © 2012 by Silicon Laboratories
C8051T620/2-DK
C8051T620/2-DK
3. Hardware Setup
See Figure 1 for a diagram of the hardware configuration.
Attach the desired daughter board to the motherboard at connectors P1 and P2.
If using the QFN Socket Daughter Board, place the device to be programmed into the socket.
Place shorting blocks on J7 and the +3VD-VDD_PWR jumper pair on J6, as shown in Figure 1.
Connect the motherboard’s P5 USB connector to a PC running the Silicon Laboratories IDE using the USB
Cable.
5. Connect the ac-to-dc power adapter to connector P3 on the motherboard.
es
ig
ns
1.
2.
3.
4.
U1
P1
P0.1 P1.2
SW1 LED2
P2.0 P2.3
P1.0
SW2
P2.1
J9
J2
J15
VPP
SILICON LABS
J7
D10
USB
P2ACTIVE
J5
U2
om
J12
D12
STOP
DEBUG
PWR
F326
J13
P5
J11
RX_DEBUG
P0.4
RX_COMM
TX_DEBUG
P0.5
TX_COMM
R8
RESET
Figure 1. Hardware Setup (Emulation Daughter Board)
N
ot
R
ec
CTS_DEBUG
P1.2
CTS_COMM
Place shorting blocks on
J7 and J6 as shown.
U1
J8
RTS_DEBUG
P1.1
RTS_COMM
VDD_PWR
VDD_PWR
VDD_PWR
VDD_PWR
D11
RUN
USB ACTIVE
CP2103
P4
PWR
J6
+3VD
VDD_EXT
VDD_DEBUG
VDD_COMM
J4
2
AC Adapter
P3
J3
VREGIN
VREGIN
www.silabs.com
J10
www.silabs.com
VBUS
VDD
SILICON LABS
P0.6
LED1
P2.2
m
en
de
d
F34A
J14
SW2
fo
r
J1C8051T62x-MB
P3
LED1
LED2
SW1
J1
C8051T62x EDB
N
ew
D
Notes:
1. Use the Reset icon in the IDE to reset the target when connected during a debug session.
2. Remove power from the motherboard and remove the USB cable before removing a daughter board from the
motherboard. Connecting or disconnecting a daughter board when the power adapter or USB cable are connected can
damage the motherboard, the daughter board, or the socketed device.
3. Remove power from the motherboard and remove the USB cable before removing a C8051T62x/32x device from the
socket. Inserting or removing a device from the socket when the power adapter or USB cable are connected can
damage the motherboard, the daughter board, or the socketed device.
4. The above hardware setup instructions configure the development system to be powered through the onboard 3.3 V
regulator. For other power options, see "7.3. Power Supply Headers (J6 and J7)" on page 15.
Rev. 0.5
USB Cable
C8051T620/2-DK
4. Software Installation
All the latest software tools and documentation can be downloaded from www.silabs.com/mcudownloads.
4.1. System Requirements
es
ig
ns
The Silicon Labs 8-bit Development Tools download package available on that web page includes the Silicon
Laboratories Integrated Development Environment (IDE), 8051 evaluation toolset, Virtual COM Port drivers for the
CP210x USB to UART Bridge, and additional documentation. Download the package and install the components
by following the on-screen instructions.
Pentium-class
One
host PC running Microsoft Windows 2000 or newer.
available USB port.
4.2. Development Tools Installation
N
ew
To install the IDE, utilities, and code examples, perform the following steps:
D
The following are the system requirements necessary to run the debug and programming tools:
1. Run the Silicon Labs 8-bit Development Tools installer downloaded from www.silabs.com/mcudownloads.
fo
r
2. In the screen titled “Select Installation Packages”, the Silicon Labs IDE, 8051 Evaluation Toolset and CP210x
Virtual COM Port drivers will be checked by default. The programs necessary to download and debug on the
MCU are the Silicon Labs IDE and the 8051 Evaluation Toolset. The CP210x Drivers are necessary to use the
UART capabilities of the target board. See “4.3. CP210x USB to UART VCP Driver Installation” for more
information about installing the CP210x drivers. See “5. Software Overview” for an overview of all applicable
software included in the web download.
3. Installers selected in Step 3 will execute in sequence, prompting the user as they install programs,
documentation, and drivers.
m
en
de
d
4.3. CP210x USB to UART VCP Driver Installation
The C8051T62x Motherboard includes a Silicon Laboratories CP2103 USB-to-UART Bridge Controller. Device
drivers for the CP2103 need to be installed before PC software, such as HyperTerminal, can communicate with the
board over the USB connection. If the “Install CP210x Drivers” option was selected during installation, this will
launch a driver “unpacker” utility.
1. Follow the steps to copy the driver files to the desired location. The default directory is C:\SiLabs\MCU\CP210x.
om
2. The final window of this installer will provide an option to install the driver on the target system. Select the
“Launch the CP210x VCP Driver Installer” option in that window if you are ready to install the driver. You do not
need to have the motherboard's USB connector plugged into the PC's USB port for this step.
ec
3. If selected, the driver installer will now launch, providing an option to specify the driver installation location. After
pressing the “Install” button, the installer will search your system for copies of previously installed CP210x
Virtual COM Port drivers. It will let you know when your system is up-to-date. The driver files included in this
installation have been certified by Microsoft.
R
4. If the “Launch the CP210x VCP Driver Installer” option was not selected in Step 3, the installer can be found in
the location specified in Step 2 (by default, C:\SiLabs\MCU\CP210x\Windows). At this location, run
CP210xVCPInstaller.exe.
N
ot
5. To complete the installation process, connect the included USB cable between the host computer and the
COMM USB connector (P4) on the C8051T62x Motherboard. Windows will automatically finish the driver
installation. Information windows will pop up from the taskbar to show the installation progress.
6. If needed, the driver files can be uninstalled by selecting the “Silicon Laboratories CP210x USB to UART Bridge
(Driver Removal)” option in the “Add or Remove Programs” window.
Rev. 0.5
3
C8051T620/2-DK
5. Software Overview
The following software is necessary to build a project, download code to, and communicate with the target
microcontroller.
Evaluation Toolset
Labs Integrated Development Environment (IDE)
es
ig
ns
8051
Silicon
Other useful software included in the Silicon Labs 8-bit Development Tools package from the Silicon Labs
Downloads web site ( www.silabs.com/mcudownloads) includes:
Configuration
Wizard 2
µVision2, µVision3, and µVision4 Drivers
MCU Production Programmer and Flash Programming Utilities
Keil
D
5.1. 8051 Evaluation Toolset
N
ew
The Silicon Labs IDE has native support for many third-party 8051 toolsets. Included with this kit is an 8051
evaluation assembler, compiler, and linker. For further information on the tools, including limitations, see the
corresponding application note. Application notes can be found on the Silicon Labs web site (http://
www.silabs.com/appnotes). See Table 1 for a list of supported toolsets and associated application notes.
Table 1. Supported Third Party 8051 Toolsets
fo
r
Application Note
“AN104: Integrating Keil 8051 Tools into the Silicon Labs IDE”
“AN125: Integrating Raisonance 8051 Tools into the Silicon Labs IDE”
“AN126: Integrating Tasking 8051 Tools into the Silicon Labs IDE”
“AN140: Integrating Hi-TECH 8051 Tools into the Silicon Labs IDE”
“AN198: Integrating SDCC 8051 Tools into the Silicon Labs IDE”
“AN236: Integrating IAR 8051 Tools into the Silicon Labs IDE”
m
en
de
d
Toolset
Keil
Raisonance
Tasking
HI-TECH
SDCC
IAR
5.2. Silicon Labs IDE
The Silicon Labs IDE integrates a source-code editor, source-level debugger, and in-system programmer. The
following sections discuss how to open an example project in the IDE, build the source code, and download it to the
target device.
om
5.2.1. Running the T620_Blinky or T622_Blinky example program
The T620_Blinky or T622_Blinky example program blinks an LED on the target board.
N
ot
R
ec
1. Open the Silicon Labs IDE from the Start menu.
2. Select ProjectOpen Project to open an existing project.
3. Browse to the C:\SiLabs\MCU\Examples\C8051T620_1_6_7_T320_3\Blinky or SiLabs\MCU\Examples\C8051T622_3_T326_7\Blinky directory (default) and select the T620_Blinky_C.wsp or
T622_Blinky_C.wsp project file. Click Open.
4. Once the project is open, build the project by clicking on the Build/Make Project button in the toolbar or
selecting ProjectBuild/Make Project from the menu.
Note: After the project has been built the first time, the Build/Make Project command will only build the
files that have been changed since the previous build. To rebuild all files and project dependencies, click
on the Rebuild All button in the toolbar or select ProjectRebuild All from the menu.
5. Before connecting to the target device, several connection options may need to be set. Open the Connection Options window by selecting OptionsConnection Options... in the IDE menu. First, select the
“USB Debug Adapter” option. Next, the correct “Debug Interface” must be selected. C8051T62x/32x
devices use Silicon Labs “C2” 2-wire debug interface. Once all the selections are made, click the OK button to close the window.
4
Rev. 0.5
C8051T620/2-DK
es
ig
ns
6. Click the Connect button in the toolbar or select DebugConnect from the menu to connect to the
device.
7. Download the project to the target by clicking the Download Code button in the toolbar.
Note: To enable automatic downloading if the program build is successful, select Enable Automatic Connect/Download after Build in the ProjectTarget Build Configuration dialog. If errors occur during the
build process, the IDE will not attempt the download.
8. Click on the Go button (green circle) in the toolbar or by selecting DebugGo from the menu to start running the firmware. The LED on the target board will start blinking.
5.2.2. Creating a New Project
Use the following steps to create a new project. Once steps 1–5 in this section are complete, continue with Step 3
from Section 5.2.1.
N
ot
R
ec
om
m
en
de
d
fo
r
N
ew
D
1. Select ProjectNew Project to open a new project and reset all configuration settings to default.
2. Select FileNew File to open an editor window. Create your source file(s) and save the file(s) with a recognized extension, such as .c, .h, or .asm, to enable color syntax highlighting.
3. Right-click on “New Project” in the Project Window. Select Add files to project. Select files in the file
browser and click Open. Continue adding files until all project files have been added.
4. For each of the files in the Project Window that you want assembled, compiled, and linked into the target
build, right-click on the file name and select Add file to build. Each file will be assembled or compiled as
appropriate (based on file extension) and linked into the build of the absolute object file.
Note: If a project contains a large number of files, the “Group” feature of the IDE can be used to organize.
Right-click on “New Project” in the Project Window. Select Add Groups to project. Add predefined groups
or add customized groups. Right-click on the group name and choose Add file to group. Select files to be
added. Continue adding files until all project files have been added.
5. Save the project when finished with the debug session to preserve the current target build configuration,
editor settings, and the location of all open debug views. To save the project, select ProjectSave Project As... from the menu. Create a new name for the project and click on Save.
Rev. 0.5
5
C8051T620/2-DK
5.3. Configuration Wizard 2
m
en
de
d
fo
r
N
ew
D
es
ig
ns
Configuration Wizard 2 is a code generation tool for all Silicon Laboratories devices. Code is generated through the
use of dialog boxes for each device peripheral as shown in Figure 2.
Figure 2. Configuration Wizard 2 Utility
om
The Configuration Wizard utility helps accelerate development by automatically generating initialization source
code to configure and enable the on-chip resources needed by most design projects. In just a few steps, the wizard
creates complete startup code for a specific Silicon Laboratories MCU. The program is configurable to provide the
output in C or assembly language.
ec
For more information, refer to the Configuration Wizard 2 help available under the Help menu in Configuration
Wizard 2 or refer to the Configuration Wizard 2 documentation. Documentation and software are available from the
downloads webpage: www.silabs.com/mcudownloads.
5.4. Keil uVision2, uVision3, and uVision4 Silicon Laboratories Drivers
N
ot
R
As an alternative to the Silicon Laboratories IDE, the µVision debug driver allows the Keil µVision2, µVision3, and
µVision4 IDEs to communicate with Silicon Laboratories’ on-chip debug logic. In-system Flash memory
programming integrated into the driver allows for rapid updating of target code. The µVision2, µVision3, and
µVision4 IDEs can be used to start and stop program execution, set breakpoints, check variables, inspect and
modify memory contents, and single-step through programs running on the actual target hardware.
For more information, refer to the µVision driver documentation. The documentation and software are available
from the downloads webpage: www.silabs.com/mcudownloads.
6
Rev. 0.5
C8051T620/2-DK
5.5. Programming Utilities
es
ig
ns
The Silicon Labs IDE is the primary tool for downloading firmware to the MCU during development. There are two
software programming tools that are intended for use during prototyping or in the field: the MCU Production
Programmer and the Flash Programming Utilities. The MCU Production Programmer is installed with the IDE to the
directory, C:\Silabs\MCU\Utilities\Production Programmer\ (default). The Flash Programming Utilities can be
optionally installed from the web installer, and are installed to C:\Silabs\MCU\Utilities\FLASH Programming\
(default).
5.6. ToolStick Terminal
D
The onboard debug circuitry provides both an in-system programming and debugging interface and a
communications interface to the target microcontroller's UART. The ToolStick Terminal software can access the
debug hardware's communications path and provides a terminal-like interface on the PC. Note that for concurrent
debugging and UART communications, the CP2103 USB-to-UART bridge is also included onboard.
N
ot
R
ec
om
m
en
de
d
fo
r
N
ew
In addition to the standard terminal functions (Send File, Receive File, Change Baud Rate), two GPIO pins on the
target microcontroller can be controlled using the terminal for either RTS/CTS handshaking or softwareconfigurable purposes. The ToolStick Terminal software is available on the downloads webpage: www.silabs.com/
mcudownloads.
Rev. 0.5
7
C8051T620/2-DK
6. Example Source Code
es
ig
ns
Example
source
code
and
register
definition
files
are
provided
by
default
in
the
SiLabs\MCU\Examples\C8051T620_1_6_7_T320_3 or SiLabs\MCU\Examples\C8051T622_3_T326_7 directory
during IDE installation. These files may be used as a template for code development.
6.1. Register Definition Files
Register definition files C8051T620.inc, C8051T622.inc, C8051T620_defs.h, C8051T622_defs.h, and
compiler_defs.h define all SFR registers and bit-addressable control/status bits. They are installed by default into
the SiLabs\MCU\Examples\C8051T620_1_6_7_T320_3 or SiLabs\MCU\Examples\C8051T622_3_T326_7
directory during IDE installation. The register and bit names are identical to those used in the C8051T620-21-2627_T320-3 or C8051T622-23_T326-27 data sheet.
D
6.2. Blinking LED Example
N
ot
R
ec
om
m
en
de
d
fo
r
N
ew
The example source files T620_Blinky.asm and T620_Blinky.c or T622_Blinky.asm and T622_Blinky.c show
examples of several basic C8051T62x functions. These include disabling the watchdog timer (WDT), configuring
the Port I/O crossbar, configuring a timer for an interrupt routine, initializing the system clock, and configuring a
GPIO port. When compiled/assembled and linked, these programs flash the green LED on the C8051T62x
Motherboard about five times a second using the interrupt handler with a timer.
8
Rev. 0.5
C8051T620/2-DK
7. Development Boards
P1,
P2
P3
Daughter board connection
Power connector that accepts input from 7.5 to 15 V dc unregulated power adapter
USB connector for UART to USB communications interface
USB Debug interface connector
Analog I/O terminal block
Port 0 header
Port 1 header
Port 2 header
Port 3 header with access to VDD and GND
Power supply selection header (See "7.3. Power Supply Headers (J6 and J7)" on page 15)
Power supply enable header that connects power source selected on J6 to the board's main
power supply net
Communications interface control signal header
Connects port pins to the switches labeled “SW1” and “SW2”
Connects port pins to the LEDs labeled “LED1” and “LED2”
Communications interface data signal header
Connects potentiometer to the port pin, P2.5
Additional connections to ground
Connects an external VREF from J1 to P0.7
VPP supply connection used when programming EPROM devices
D
P4
es
ig
ns
The C8051T620/2 Development Kit includes a motherboard that interfaces to various daughter boards. The
C8051T62x Emulation Daughter Board contains a C8051F34A device to be used for preliminary software
development. The C8051T620 Socket Daughter Board and C8051T622 Socket Daughter Board allow
programming and evaluation of the actual C8051T62x devices. Numerous input/output (I/O) connections are
provided on the motherboard to facilitate prototyping. Figure 3 shows the C8051T62x Motherboard and indicates
locations for various I/O connectors. Figure 4 shows the factory default shorting block positions. Figures 5, 6, and 7
show the available C8051T62x daughter boards. Figures 8, 9, 10, and 11 show the available C8051T32x daughter
boards.
P5
N
ew
J1
J2
J3
J4
J5
J6
fo
r
J7
J8
m
en
de
d
J9
J10
J11
J12
J13
J14
N
ot
R
ec
om
J15
Rev. 0.5
9
C8051T620/2-DK
J14
C8051T62x-MB
P1
SW2
P0.1 P1.2
SW1 LED2
P2.0 P2.3
P1.0
SW2
P2.1
SILICON LABS
www.silabs.com
P0.6
LED1
P2.2
J9
J2
P3
J10
J15
VPP
J7
J3
PWR
J6
D10
USB
P2ACTIVE
F326
CTS_DEBUG
P1.2
CTS_COMM
J12
RX_DEBUG
P0.4
RX_COMM
J13
P5
J11
TX_DEBUG
P0.5
TX_COMM
RESET
R8
fo
r
P4
DEBUG
PWR
U1
J8
RTS_DEBUG
P1.1
RTS_COMM
D12
STOP
N
ew
USB ACTIVE
CP2103
D11
RUN
J5
D
J4
U2
VDD_PWR
VDD_PWR
VDD_PWR
VDD_PWR
+3VD
VDD_EXT
VDD_DEBUG
VDD_COMM
es
ig
ns
SW1
J1
LED1
LED2
m
en
de
d
Figure 3. C8051T62x Motherboard
SW1
J1
J14
C8051T62x-MB
P1
LED1
LED2
P1.0
SW2
P2.1
SW2
P0.1 P1.2
SW1 LED2
P2.0 P2.3
J9
J2
P3
J15
VPP
J7
om
ec
D10
USB
P2ACTIVE
USB ACTIVE
D12
STOP
DEBUG
PWR
U1
J8
RTS_DEBUG
P1.1
RTS_COMM
VDD_PWR
VDD_PWR
VDD_PWR
VDD_PWR
D11
RUN
J5
R
N
ot
PWR
J6
+3VD
VDD_EXT
VDD_DEBUG
VDD_COMM
J4
CP2103
www.silabs.com
J10
J3
U2
SILICON LABS
P0.6
LED1
P2.2
F326
CTS_DEBUG
P1.2
CTS_COMM
J12
J13
P5
J11
P4
RX_DEBUG
P0.4
RX_COMM
TX_DEBUG
P0.5
TX_COMM
R8
RESET
Figure 4. C8051T62x Motherboard Default Shorting Block Positions
10
Rev. 0.5
C8051T620/2-DK
U1
F34A
VBUS
VDD
SILICON LABS
www.silabs.com
VREGIN
VREGIN
D
P3
es
ig
ns
C8051T62x EDB
N
ew
Figure 5. C8051T62x Emulation Daughter Board
C8051T62x QFN32 SKT DB
fo
r
VDD
VREGIN
J1
J2
VDD
VIO
m
en
de
d
P3
VBUS
VREGIN
J3
SILICON LABS
www.silabs.com
Figure 6. C8051T620 QFN32 Socket Daughter Board
SILICON LABS
J3
VBUS
VREGIN
www.silabs.com
J1
VDD
VREGIN
P3
J2
VDD
VIO
N
ot
R
ec
om
C8051T622 QFN24 SKT DB
Figure 7. C8051T622 QFN24 Socket Daughter Board
Rev. 0.5
11
C8051T620/2-DK
C8051T320 QFP32 SKT DB
SILICON LABS
VBUS
VREGIN
es
ig
ns
J2
www.silabs.com
P3
D
VDD
VREGIN
J1
N
ew
Figure 8. C8051T320 QFP32 Socket Daughter Board
C8051T321 QFN28 SKT DB
SILICON LABS
www.silabs.com
J1
SILICON LABS
J3
VBUS
VREGIN
VDD
VREGIN
m
en
de
d
P3
fo
r
J2
Figure 9. C8051T321 QFN28 Socket Daughter Board
12
VBUS
VREGIN
www.silabs.com
J1
VDD
VREGIN
P3
J2
VDD
VIO
N
ot
R
ec
om
C8051T326 QFN28 SKT DB
Figure 10. C8051T326 QFN28 Socket Daughter Board
Rev. 0.5
C8051T620/2-DK
C8051T327 QFN28 SKT DB
J3
SILICON LABS
es
ig
ns
VBUS
VREGIN
www.silabs.com
J1
D
VDD
VREGIN
P3
N
ot
R
ec
om
m
en
de
d
fo
r
N
ew
Figure 11. C8051T327 QFN28 Socket Daughter Board
Rev. 0.5
13
C8051T620/2-DK
7.1. System Clock Sources
7.2. Switches, LEDs, and Potentiometer (J9, J10, and J12)
es
ig
ns
The C8051T62x/32x devices feature a calibrated internal oscillator that is enabled as the system clock source on
reset. After reset, the internal oscillator operates at a frequency of 48 MHz (±1.5%) by default but may be
configured by software to operate at other frequencies. Therefore, in many applications, an external oscillator is not
required. However, if you wish to operate the C8051T62x/32x device at a frequency not available with the internal
oscillator, an external oscillator source may be used. Refer to the C8051T620-21-26-27_T320-3 or C8051T62223_T326-27 data sheet for more information on configuring the system clock source.
D
Three switches are provided on the motherboard. The RESET switch is connected to the RST pin of the
C8051T62x/32x. Pressing RESET puts the device into its hardware-reset state. The switch labeled “SW1” can be
connected to the C8051T62x/32x's general-purpose I/O (GPIO) pins P0.1 and P2.0, and “SW2” can be connected
to the C8051T62x/32x's general-purpose I/O (GPIO) pins P1.0 and P2.1 through header J9. Pressing a switch
generates a logic low signal on the port pin. Remove its shorting block from the J9 header to disconnect the switch
from the port pin.
fo
r
N
ew
Seven LEDs are also provided on the motherboard. The red LED labeled “PWR” (D4) is used to indicate a power
connection to the motherboard. The green LED labeled “RUN” (D10) turns on when the debug circuitry is in a
running state; the red LED labeled “STOP” (D11) turns on when the debug circuitry is in a halted state, and the
orange LED labeled “DEBUG PWR” (D12) indicates whether the debug adapter circuit is being powered through
P5's USB connector. The red LED labeled “VPP” (D7) indicates when the VPP programming voltage is being
applied to the device. The green LEDs, labeled “LED1” (D1) and “LED2” (D2), can be connected to C8051T62x/
32x's GPIO pins through header J10. Remove its shorting block from the header to disconnect an LED from the
port pin. The red LED labeled “USB ACTIVE” (D13) will turn on whenever the CP2103 USB-to-UART bridge is
connected to a PC and has successfully completed enumeration.
N
ot
R
ec
om
m
en
de
d
Also included on the C8051T62x Motherboard is a 10 k thumbwheel rotary potentiometer, reference number R8.
The potentiometer can be connected to the C8051T62x/32x's P2.5 pin through the J12 header. Remove the
shorting block from the header to disconnect the potentiometer from the port pin.
14
Rev. 0.5
C8051T620/2-DK
Table 2 lists the port pins and headers corresponding to the switches, LEDs, and potentiometer.
Table 2. Motherboard I/O Descriptions
Component Name
I/O
Header
Switch
SW1
Daughter Card's P0.1
Daughter Card’s P2.0
J9 [2-4]
J9 [4-6]
Switch
SW2
Daughter Card’s P1.0
Daughter Card’s P2.1
J9 [1-3]
J9 [3-5]
RESET
SW3
Daughter Card's RST/C2CK
None
Green LED labeled “LED1”
D1
Daughter Card's P0.6
Daughter Card's P2.2
J10 [2-4]
J10 [4-6]
Green LED labeled “LED2”
D2
Daughter Card’s P1.2
Daughter Card's P2.3
J10 [1-3]
J10 [3-5]
Red LED labeled “PWR”
D4
Daughter Card's VDD
J6, J7
Red LED labeled “VPP”
D7
Daughter Card's VPP pin
(See "VPP Pin Sharing" on
page 17)
J15
Green LED labeled “RUN”
D10
Debug Adapter Signal
None
Red LED labeled “STOP”
D11
Debug Adapter Signal
None
Orange LED labeled “DEBUG PWR”
D12
Debug Adapter Signal
None
Green LED labeled “USB ACTIVE”
D13
U2 CP2103's SUSPEND
None
Potentiometer
R8
Daughter Card's P2.5
J12
m
en
de
d
fo
r
N
ew
D
es
ig
ns
Description
7.3. Power Supply Headers (J6 and J7)
The main power supply of the motherboard, which is used to power the daughter board, can be provided by either
the USB Debug Adapter’s on-chip voltage regulator, the CP2103 USB-to-UART bridge’s on-chip voltage regulator,
P3 and its associated circuitry, or an external voltage applied to the VDD_EXT connection on J1. To select a power
supply, place a shorting block on J6 across the appropriate pin pair, as shown in Figure 12. To connect the main
power supply to an attached daughter board, place a shorting block across J7.
ec
om
Notes:
1. Only one shorting block should be placed on J6 at a time.
2. To use the CP2103’s voltage regulator as the board's power supply, a USB cable must be connected to P4, and the USB
ACTIVE LED (D2) must be on.
3. To use the USB Debug Adapter’s voltage regulator as the board's power supply, a USB cable must be connected to P5,
and the DEBUG PWR LED (D12) must be on.
R
J7
VDD_T620
J7
VDD_PWR
VDD_T620
VDD_PWR
+3VD
VDD_EXT
VDD_DEBUG
VDD_COMM
J6
N
ot
+3VD
VDD_EXT
VDD_DEBUG
VDD_COMM
J7
VDD_PWR
VDD_T620
VDD_PWR
+3VD
VDD_EXT
VDD_DEBUG
VDD_COMM
J6
+3.3V Regulator Power
(From P3)
J7
VDD_PWR
VDD_T620
VDD_PWR
+3VD
VDD_EXT
VDD_DEBUG
VDD_COMM
J6
CP2103 Regulator Power
(From USB at P4)
VDD_PWR
J6
Debug Circuit Power
(From USB at P5)
VDD_PWR
External Power Source
(From J1 Connector)
Figure 12. J6 and J7 Shorting Block Configuration for Power Options
Rev. 0.5
15
C8051T620/2-DK
7.4. USB Debug Adapter (DEBUG/P5)
es
ig
ns
A Universal Serial Bus (USB) connector (P5) provides the onboard debug and programming interface. The debug/
programming MCU and associated circuitry are powered through the USB connector, which can also supply the
rest of the motherboard by routing the USB Debug Adapter's power through J6. The USB Debug Adapter also
provides a data communications interface that can be used when the debug adapter is not debugging or
programming a C8051T62x/32x device.
7.5. UART to USB Communications Interfaces (COMM/P4)
The C8051T62x Motherboard provides UART to USB communications interfaces through both the CP2103 USBto-UART bridge device and the communications interface of the USB Debug Adapter.
D
The CP2103 bridge device connects to a PC through the USB connector labeled “COMM” (P4). This USB
connector supplies power to the CP2103 and can supply power to the rest of the motherboard by configuring J6
and J7 as shown in Figure 12. To use the CP2103 as a communications interface, the CP2103 Virtual COM Port
drivers must be installed on a PC.
N
ew
The USB Debug Adapter's communications interface connects to a PC through P5. Access to the USB Debug
Adapter's communications interface is provided by the Windows program called “ToolStick Terminal”, which is
available for download for free from the Silicon Laboratories website. See the ToolStick Terminal help file for
information on how to use ToolStick Terminal.
7.6. Communications Interface Selector Headers (J8 and J11)
m
en
de
d
fo
r
The C8051T62x Motherboard routes the C8051T62x/32x's P0.4 (UART TX) and P0.5 (UART RX) to J11 where
those signals can be connected to either the CP2103 USB-To-UART bridge or the USB Debug Adapter. The
motherboard also allows the C8051T62x/32x's P1.1 and P1.2 to be used as the UART control signals, CTS and
RTS. These two signals are routed to J8, where they can be connected to either the CP2103 or the USB Debug
Adapter.
The jumper options for using either the CP2103 or the Debug Adapter circuit for UART communications can be
found in Figure 13.
J8
RTS_DEBUG
P1.1
RTS_COMM
CTS_DEBUG
P1.2
CTS_COMM
RTS_DEBUG
P1.1
RTS_COMM
CTS_DEBUG
P0.5
CTS_COMM
RX_DEBUG
P0.4
RX_COMM
J11
om
RX_DEBUG
P0.4
RX_COMM
RTS_DEBUG
P1.2
CTS_COMM
J11
TX_DEBUG
P0.5
TX_COMM
Debug Adapter Comms
(USB Connection at P5)
ec
CP2103 Bridge
(USB Connection at P4)
J8
Figure 13. Shorting Block Configuration for UART Communication Options
R
7.7. PORT I/O Connectors (J2, J3, J4, and J5)
N
ot
Each of the C8051T62x/32x's I/O pins, as well as +3VD and GND, are routed to headers J2 through J5. J2
connects to the microcontroller's Port 0 pins; J3 connects to Port 1; J4 connects to Port 2, and J5 connects to
Port 3.
16
Rev. 0.5
C8051T620/2-DK
7.8. Analog I/O (J1 and J14)
es
ig
ns
Three of the C8051T62x/32x target device's port pins are connected to the J1 terminal block. The terminal block
also allows users to input an external voltage that can be used as the power supply of the board. Refer to Table 3
for the J1 terminal block connections. Placing a shorting block on J14 will connect the P0.7/VREF signal on J1 to
the P0.7 pin of the device.
Table 3. J1 Terminal Block Descriptions
Description
1
VREGIN
2
VIO
3
GND
4
P2.5 (Analog Input)
5
P0.7/VREF (routed to header J14)
6
VDD_EXT (routed to header J6)
N
ew
D
Pin #
7.9. VPP Connection (J15)
m
en
de
d
fo
r
The C8051T62x/32x devices require an external 6.0 V programming voltage applied to the VPP pin during device
programming. The VPP pin on these devices is shared with P1.5 or P1.1 depending on the device. During
programming, the VPP voltage is automatically enabled when needed. Header J15 is provided to allow the user to
disconnect the programming circuitry from the VPP pin to avoid interfering with the normal application operation of
the GPIO pin. When programming the device, J15 should be shorted with a shorting block. When running normal
application code, J15 can be removed. See Table 4 for more information on which port pins are shared with VPP.
Device
Pin Shared with VPP
C8051T620
C8051T621
C8051T626
C8051T627
C8051T320
C8051T321
C8051T322
C8051T323
P1.5
C8051T622
C8051T623
C8051T326
C8051T327
P1.1
N
ot
R
ec
om
Table 4. VPP Pin Sharing
Rev. 0.5
17
C8051T620/2-DK
7.10. Using Alternate Supplies with the C8051T62x Development Kit
es
ig
ns
For most evaluation purposes, the onboard 3.3 V supply regulator is sufficient to be used as a VDD power supply.
However, in applications where a different supply voltage is desired (e.g., 1.8 V), an external supply voltage can be
applied to the board at the analog connector (J1). Some devices in the C8051T62x/32x family also support a
separate voltage input for the input/output voltage of the port pins. This Voltage Input/Output (VIO) should be input
to J1 on Pin 2. See the C8051T620-21-26-27_T320-3 or C8051T622-23_T326-27 data sheet for more information
about VIO usage and constraints.
N
ot
R
ec
om
m
en
de
d
fo
r
N
ew
D
Notes:
1. When programming a C8051T62x/32x device, VDD must be at least 3.3 V. VDD can be supplied directly to the device,
or the on-chip 5 V regulator can be used.
2. If an external supply voltage is desired, the shorting block on J6 should be placed so that the Pin 3 (VDD_EXT) is
shorted to Pin 4 (VDD_PWR).
18
Rev. 0.5
N
ot
Rev. 0.5
fo
r
N
ew
Figure 14. C8051T62x Motherboard Schematic (1 of 2)
m
en
de
d
om
ec
R
es
ig
ns
D
C8051T620/2-DK
8. Schematics
19
N
ot
20
Rev. 0.5
fo
r
N
ew
Figure 15. C8051T62x Motherboard Schematic (2 of 2)
m
en
de
d
om
ec
R
es
ig
ns
D
C8051T620/2-DK
N
ot
Rev. 0.5
fo
r
N
ew
es
ig
ns
D
Figure 16. C8051T62x Emulation Daughter Board Schematic
m
en
de
d
om
ec
R
C8051T620/2-DK
21
N
ot
22
Rev. 0.5
fo
r
N
ew
es
ig
ns
D
Figure 17. C8051T620 QFN-32 Daughter Board Schematic
m
en
de
d
om
ec
R
C8051T620/2-DK
N
ot
Rev. 0.5
fo
r
N
ew
es
ig
ns
D
Figure 18. C8051T622 QFN-24 Daughter Board Schematic
m
en
de
d
om
ec
R
C8051T620/2-DK
23
N
ot
24
Rev. 0.5
fo
r
N
ew
es
ig
ns
D
Figure 19. C8051T320 QFP-32 Daughter Board Schematic
m
en
de
d
om
ec
R
C8051T620/2-DK
N
ot
Rev. 0.5
fo
r
N
ew
es
ig
ns
D
Figure 20. C8051T321 QFN-28 Daughter Board Schematic
m
en
de
d
om
ec
R
C8051T620/2-DK
25
N
ot
26
Rev. 0.5
fo
r
N
ew
es
ig
ns
D
Figure 21. C8051T326 QFN-28 Daughter Board Schematic
m
en
de
d
om
ec
R
C8051T620/2-DK
N
ot
Rev. 0.5
fo
r
N
ew
es
ig
ns
D
Figure 22. C8051T327 QFN-28 Daughter Board Schematic
m
en
de
d
om
ec
R
C8051T620/2-DK
27
C8051T620/2-DK
DOCUMENT CHANGE LIST
Revision 0.2 to Revision 0.3
Updated
es
ig
ns
"4.2. Development Tools Installation"
on page 3.
Updated "4.3. CP210x USB to UART VCP
Driver Installation" on page 3.
Updated Figure 17 on page 22.
Updated Figure 18 on page 23.
Updated Figure on page 28.
Updated
"1. Kit Contents" on page 1.
"2. About the Daughter Boards" on
page 1.
Updated "6. Example Source Code" on page 8.
Updated
project paths
Updated
"7. Development Boards" on page 9.
Updated "8. Schematics" on page 19.
Figures 19, 20, 21, and 22.
C8051T62x references to include
C8051T32x devices.
Updated data sheet references.
fo
r
Added
Updated
m
en
de
d
Revision 0.4 to Revision 0.5
Updated
"1. Kit Contents" on page 1.
document to reflect change from CDROM based installation to web-based installer.
Updated various sections to include the new
C8051T626/7 part numbers.
N
ot
R
ec
om
Updated
28
N
ew
Updated
D
Revision 0.3 to Revision 0.4
Rev. 0.5
es
ig
ns
D
N
ew
fo
r
One-click access to MCU and
wireless tools, documentation,
software, source code libraries &
more. Available for Windows,
Mac and Linux!
SW/HW
Quality
Support and Community
www.silabs.com/simplicity
www.silabs.com/quality
community.silabs.com
om
IoT Portfolio
www.silabs.com/IoT
m
en
de
d
Simplicity Studio
N
ot
R
ec
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,
USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com
">