Wincor Nixdorf BA63GV Operating Manual
Advertisement
Advertisement
BA63GV
Graphical Customer Display
Operating Manual
B EETLE ™ is a registered trademark of Wincor Nixdorf GmbH & Co. KG Copyright© Wincor Nixdorf GmbH & Co. KG, 2007 The reproduction, transmission or use of this document or its contents is not permitted without express authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability; technical modifications possible.
BA63GV
Graphical Customer Display
Operating Manual
Edition Aug 2008
Contents
Contents
CONTENTS ...................................................................................................4
MANUFACTURER’S DECLARATION ...........................................................6
FCC C LASS A D ECLARATION .........................................................................6
T ESTED S AFETY ...........................................................................................7
N OTE ON C ARE .............................................................................................7
W ARRANTY ..................................................................................................7
R ECYCLING THE BA63GV..............................................................................8
OVERVIEW ...................................................................................................9
CABLE INSTALLATION..............................................................................11
F OR ROD MOUNTED ....................................................................................11
F OR S WIVEL BASE .......................................................................................13
CONTROL SEQUENCES ............................................................................15
VT100 C OMMANDS .....................................................................................15
POS C OMMANDS ........................................................................................16
S CREEN C OORDINATES ...............................................................................17
Text-mode .............................................................................................17
Pixel-mode ............................................................................................17
C ONTROL CODES AND C OMMAND D ESCRIPTION .............................................18
Backspace (without deleting) .................................................................18
Line feed................................................................................................18
Carriage return ......................................................................................18
Clear Display .........................................................................................18
Position cursor.......................................................................................19
Delete to end of line...............................................................................19
Set Country code ...................................................................................20
Display identification ..............................................................................21
Character Set identification ....................................................................21
Firmware identification ...........................................................................22
Set Pixel position ...................................................................................22
Set Character Resolution .......................................................................23
Dump user-define image to display ........................................................23
Set Clock...............................................................................................24
Set Watch Dog of cable monitor.............................................................24
Load User Logo .....................................................................................24
Set Line mode .......................................................................................25
Turn On/Off display................................................................................25
01750153250 B BA63GV Graphic Customer Display – Operating Manual
Contents Set baud rate for serial port....................................................................26
C OMMANDS FOR USB INTERFACE .................................................................27
Write Data Command ............................................................................27
Read Configuration................................................................................27
Reset Request .......................................................................................28
Status Request ......................................................................................28
Request self-test....................................................................................28
UPDATING THE FIRMWARE ......................................................................29
CHARACTER SETS ....................................................................................30
H ANDLING TEXT AND CONTROL SEQUENCE .....................................................30
Displayable Characters..........................................................................30
Undefined Characters and Control sequence .........................................30
B UILD IN CHARACTER SET ............................................................................31
IBM 437.................................................................................................31
International Characters.........................................................................31
L OADABLE C HARACTER S ETS .......................................................................32
Thai Character Set.................................................................................32
2-Byte Character Sets............................................................................33
CONFIGURING THE DEVICE......................................................................34
TECHNICAL DATA .....................................................................................35
BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Manufacturers Certification and notes
Manufacturer’s Declaration
This device fulfils the requirements of the EEC directives 2004/108/EC “Electromagnetic Compatibility”
FCC Class A Declaration
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his expense. Modifications not authorized by the manufacturer may void user authority to operate this device. This class A digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe A est conforme à la norme NMB-003 du Canada.
Wincor Nixdorf International GmbH (WN) accepts no responsibility for radio and television reception interference resulting from unauthorized modifications to the equipment. Furthermore, neither cables nor devices which have not been approved for use by WN may be connected. The user shall be held responsible for interference caused in this manner. Device repairs must be carried out by authorized personnel. All guarantee and liability claims are automatically excluded if repairs have been carried out by unauthorized personnel. 01750153250 B BA63GV Graphic Customer Display – Operating Manual 6
Manufacturer’s Certification and notes
Tested Safety
The device has received the UL symbol and cUL symbol.
Note on Care
Wipe the customer display with a damp cloth as required. Solvents must not be used under any circumstances as they may damage the plastic.
Warranty
Wincor Nixdorf generally guarantees a limited warranty engagement for 12 months beginning with the date of delivery. This warranty engagement covers all those damages which occur despite a normal use of the product. Damages because of § § § improper or insufficient maintenance, improper use of the product or unauthorized modifications of the product, inadequate location or surroundings they will not be covered by the warranty. For details please consult your contract documents. 7 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Manufacturers Certification and notes
Recycling the BA63GV
Environmental protection does not begin when it is time to dispose of the BA63GV; it begins with the manufacturer. This product was designed according to our internal norm “Environmental conscious product design and development”. The BA63 is manufactured without the use of CFCs und CCHS and is produced mainly from reusable components and materials. The processed plastics can, for the most part, be recycled. Even the precious metals can be recovered, thus saving energy and costly raw materials. Please do not stick labels onto plastic case parts. This would help us to re-use components and material. At this time, there are still some parts that are not reusable. Wincor Nixdorf guarantees the environmentally safe disposal of these parts in a Recycling Center, which is certified pursuant to ISO 9001. So don’t simply throw your BA63GV on the scrap heap when it has served its time, but take advantage of the environmentally smart, up-to-date recycling methods! Please contact your competent branch office for information on how to return and re-use devices and disposable materials. 01750153250 B BA63GV Graphic Customer Display – Operating Manual 8
Overview
Overview
The BA63GV customer display is mainly used in POS installations that are designed in modular form. It is available in several forms: swivel based, pole mounted or keyboard-mounted. The display is a graphical vacuum florescent display (VFD) with a screen resolution of 256 ´ 64 pixels. It is capable of displaying 2 or 4 lines of up to 32 Latin characters per line. Besides the built-in ASCII character set, it also supports 2-byte character sets downloadable via software. The character resolution for the standard (1-byte code) character is 8 ´ 16 (W ´ H) pixels and, the 2-byte code character is 16 ´ 16 pixels The device has the capability to display downloaded bitmap pictures. With this feature, user can display user-define image. The display is connected to the point of sale system through a RS232C or USB interface. The power (12V DC) for the display is also supplied via this interface. The following three mounting options of the display are available to meet individual installation requirements:
Figure 1 BA63GV on swivel base
9 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Overview
Figure 2 BA63GV pole-mounted
The tube diameter is 40 mm (+ 0.3 mm / - 0.1 mm). The tube is ordered separately. The connection cables are available in different lengths. Cables have to be ordered separately and will be delivered separately. 01750153250 B BA63GV Graphic Customer Display – Operating Manual 10
Cable Installation
Cable Installation
For rod-mounted
(1) Press the latch to release hinge. (2) Disconnect the hinge from the device. (3) Thread the cable through the adapter. (4) And the through the hinge 11 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Cable Installation Connect the hinge and adapter together. Secure the cable in the strain relief provided. The distance between the strain relief and the tip of the connector must be 73 mm (+/- 2 mm) 01750153250 B BA63GV Graphic Customer Display – Operating Manual 12
Cable Installation
For Swivel base
(1) Press the latch to release hinge. (2) Disconnect the hinge from the customer display. (3) Thread the cable through the adapter. (4) And the through the hinge. 13 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Cable Installation Connect the hinge to the base. On the bottom side of the base, loosen one of the screws (see arrow) and rotate the cable clip about the other fastener. Guide the cable under the clip and shift the clip back to position. Tighten the screw. 01750153250 B BA63GV Graphic Customer Display – Operating Manual 14
Control Sequences
Control Sequences
The customer display is controlled via software commands. The commands are entered with the appropriate ESC sequences. The following functions are available: The BA63G customer display operates in VT100 mode, i.e. it emulates a subset of the VT100 ESC sequences and control bytes, plus vendor-specific commands.
VT100 Commands
Backspace (without deleting)
BS
Line feed Carriage return Delete display Position cursor Delete to end of line
LF CR ESC[2J ESC[Py;PxH ESC[0K
15 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
POS Commands
Set country code Display identification Character set identification Firmware identification
ESCRn ESC[0c ESC[1c ESC[2c
Set pixel position Select display resolution
ESC[Px;Pyh ESC[nB
Half dot enhancement on / off Dump user defined picture to screen Setting clock
ESC[PxE ESC[Py;PxD
Setting watch dog of cable monitor Select line mode
ESC[hh;mmT ESC[nnT
Load user logo and set display monitor
ESC[nnL ESC[PxI
Turn on / off display Set baud rate for serial interface
ESC[PxP ESC[n;mS
Control Sequences 01750153250 B BA63GV Graphic Customer Display – Operating Manual 16
Control Sequences
Screen Coordinates
Text-mode
The display area is divided into 4 lines, of 32 Latin characters per line. The coordinate of the displayed characters are always with reference to the upper left corner of the character.
Pixel-mode
In pixel-mode, the position is addressable by specifying x and y coordinates of the pixel. 17 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Control Sequences
Control codes and Command Description
This section describes the control code and escape commands supported by the device. Unless stated otherwise, all commands are common for both RS232C and USB interface.
Backspace (without deleting)
The
BS
command (hexadecimal 08) moves the cursor one space to the left. If there is a character in the position to which the cursor moves, it is not deleted. This command is ignored if the cursor is already at the first position of the line.
Line feed
The
LF
command (hexadecimal 0A) moves the invisible cursor down a line if it is positioned in one of the first three lines of the display. The column position of the cursor remains unchanged. The position of the cursor remains unchanged if it is already in the last line. The contents of the screen are scrolled up one line and the last line is deleted.
Carriage return
The cursor is moved to the beginning of the line in which it is currently positioned when the
CR
command (hexadecimal 0D) is entered. The command is ignored if the cursor is already at the beginning of the line.
Clear Display
The display can be cleared with this ESC sequence. The cursor position remains unchanged. The ESC sequence is as follows:
Code
ESC [ 2 J
Hexadecimal
1B 5B 32 4A 01750153250 B BA63GV Graphic Customer Display – Operating Manual 18
Control Sequences
Position cursor
The cursor position can be defined with this ESC sequence. The cursor is not visible on the display whilst this is being carried out. The following ESC sequence (for example) can be implemented:
Code
ESC [
Parameter
Py Px
Example Hexadecimal Meaning
Line number Column number If you select 0 for the parameter value, this is interpreted as 1 by the display. If, on the other hand, you select a value which is greater than the maximum line and column value, the display will interpret this value as the maximum value permitted. The cursor is positioned in the first column of the first line if no parameter values are entered.
Note: This command is not applicable if the selected country code is Thai.
Delete to end of line
This command deletes the characters from the cursor, cursor position is included, to the end of the line. The position of the cursor remains unchanged.
The ESC sequence is as follows:
Code
ESC [ 0 K
Hexadecimal
1B 5B 30 4B 19 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Control Sequences
Set Country code
The following ESC sequence is implemented in order to select a country specific character set:
Code
ESC R
Hexadecimal
1B 52
n
The hexadecimal value n corresponds to the country code and defines the country-specific character set. The USA character set corresponds to the default setting. 05 06 07 08 09 0A 0B 0C 63
Country code
00 01 02 03 04
Character set
USA France Germany Great Britain Denmark 1 Sweden Italy Spain 1 Japan Norway Denmark 2 Spain 2 Latin America Katakana 92 A0 B0
Country code
62 80 81 90 91
Character set
Korean 1-byte Shift JIS JIS GB Jianti GB Fanti BIG 5 Korean 2-byte Thai 4-level The above character sets listed in the left table are standard character sets. Those character sets listed on the right table are optional character sets. They are available only when the specific character set is downloaded into the device. 01750153250 B BA63GV Graphic Customer Display – Operating Manual 20
Control Sequences
Display identification
This command returns the display characteristics.
Code
ESC [ 0 c
Hexadecimal
1B 5B 30 63 Return string:
Response
ESC [ ?
Hexadecimal
1B 5B 3F
p1
3B
p2
3B
p3
3B
p4
3B
p5
63 p1 p2 p3 p4 p5 Type of display Firmware version Character set Number of lines Column/line = = = = = 3 00 80 2 4 32 LCD display currently PROM version currently FLASH version modified IBM character set
Character Set identification
This command returns the country code of the external character sets currently installed.
Code
ESC [ 1 c
Hexadecimal
1B 5B 31 63 Return string:
Response Hexadecimal
ESC [ ?
p1
3B
p2
3B … 3B
pn
63 Where p1, p2, … pn are the country codes of the external character sets currently installed. 21 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Control Sequences
Firmware identification
This command returns the boot and main firmware version and subversion numbers.
Code
ESC [ 2 c
Hexadecimal
1B 5B 32 63 Return string:
Response Hexadecimal
ESC [ ?
p1 p2
3B
p3 p4
63 Where, p1, p2 are the boot firmware version and subversion number. p3, p4 are the main firmware version and subversion number.
Set Pixel position
This command returns the display characteristics.
Code
ESC [
Hexadecimal
1B 5B
x
3B
y
68 Where, x is the vertical position y is the horizontal position x and y are decimal numbers expressed as ASCII string. Note: the origin (1, 1) is located at the top-lefttmost of the display. 01750153250 B BA63GV Graphic Customer Display – Operating Manual 22
Control Sequences
Set Character Resolution
This command sets the character resolution. After sending this command, all characters sent will be displayed in the selected resolution.
Code
ESC [
Hexadecimal
1B 5B
n
42 Where n is defined as: n 0x30 0x31 0x32 0x33 0x34 Double Byte Characters Resolution (W ´ H) 16 ´ 16 16 ´ 32 32 ´ 32 16 x 20 32 x 20 Single Byte Characters Resolution (W ´ H) 8 ´ 16 8 ´ 32 16 ´ 32 8 x 20 16 x 20 Note: Default value for
n
is “0” (0x30).
Dump user-define image to display
This command allows application to display an image on the display. The screen has pixel lines each line has 256 pixels grouped in 8 to give a total of 32 bytes per pixel line. The origin of the image can be position vertical in pixel and horizontally in byte.
Code
ESC [
Hexadecimal
1B 5B
y
3B
x
44
w d data
Below illustrate the coordinate system for image dump. 1; 1 2; 1 : : : 64; 1 1; 2 2; 2 : : : 64; 2 .... .... .... .... .... .... .... .... .... 1; 32 2; 32 : : : 64; 32 23 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Control Sequences
Set Clock
This command set the time for the internal clock. Once set, the display will maintain the time of a 24 hour clock. An image of a Beetle with blinking eyes will be displayed. This image will stay on the screen until a command or character is sent to the display.
Code
ESC [
Hexadecimal
1B 5B
hh
3B
mm
54
Set Watch Dog of cable monitor
This command defines the idle time period (no activities on the RS232 data lines) that will trigger the display of the Beetle clock.
Code
ESC [
Hexadecimal
1B 5B
mm
54
Load User Logo
This command loads the user-defined logo which will be displayed automatically when after the set idle time. The size user-defined logo must fill the entire screen.
Code
ESC [
Hexadecimal
1B 5B
nn
54
data
Where, nn = idle time period in minute data = logo image (size = 64 x 32 bytes) note: default value for
nn
is 0. 01750153250 B BA63GV Graphic Customer Display – Operating Manual 24
Control Sequences
Set Line mode
Select 2-line, 3-line or 4-line mode.
Code
ESC [
n
is defined as: 0x30 = 4-line mode 0x31 = 2-line mode 0x32 = 3-line mode
Hexadecimal
1B 5B
n
49
Turn On/Off display
This command turns the display on or off.
Code
ESC [
n
is defined as: 0x30 = OFF 0x31 = ON
Hexadecimal
1B 5B
n
50 25 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Control Sequences
Set baud rate for serial port
This command turns the display on or off. This command is applicable to RS232C interface only.
Code
ESC [
n
00 01 02 03 04 05 06 07 08
Hexadecimal
1B 5B
Baud Rate
Auto-detection 110 bps 300 bps 600 bps 1200 bps 2400 bps 4800 bps 9600 bps (default) 14400 bps 19200 bps 38400 bps 56000 bps 57600 bps 115200 bps 128000 bps ? 256000 bps ?
n
3B
m
53
m
1..0 2 3 5..4 7..6
Control Byte
00 = 5-bit data 01 = 6-bit data 10 = 7-bit data 11 = 8-bit data (default) 0 = 1 stop bit (default) 1 = 2 stop bits 0 = Disable parity 1 = Enable parity (default) 00 = Odd parity (default) 01 = Even parity 10 = Forced '1' stick parity 11 = Forced '0' stick parity Fixed at 00 01750153250 B BA63GV Graphic Customer Display – Operating Manual 26
Control Sequences
Commands for USB interface
For all the commands listed below the output report size is 32 bytes, and for the response the Input report size is 8 bytes. Pad bytes must be added to fill up the unused space.
Write Data Command
Data can be Escape sequences, control characters or data to be issued. Escape sequences can be "hacked up" (1st part in frame n, 2nd part in frame n+1). Command: 02H, 00H, Data Count, Data Bytes Response: 04H, status byte 1, status byte 2, status byte 3 Maximum length (size of output report) is 32 bytes. Maximum number of bytes in the data field is 32-3 = 29 bytes.
Read Configuration
Display identification Command: 21H, 00H, 00H, .., 00H Response: length, status byte 0, status byte 1, status byte 3, “Pn1;Pn2;Pn3;Pn4;Pn5;Pn6;Pn7” Where, Pn1 = type of display Pn2 = current code page Pn3 = country code Pn4 = number of lines Pn5 = number of columns Pn6 = Reserved (not used) Pn7 = serial number (10 characters) 27 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Control Sequences
Reset Request
A reset will force a soft-reset and thus re-enumeration of the device. Command: 00H, 40H, 00H, .., 00H Response: None
Status Request
Status is requested. Command: 00H, 20H, 00H, .., 00H Response: 04H, status byte 1, status byte 2, status byte 3
Request self-test
A self test is performed. Command: 00H, 10H, 00H, .., 00H Response: 04H, status byte 1, status byte 2, status byte 3 Status Byte 1: Status Byte 2: Status Byte 3: Bit 4...0 Bit 5 Bit 6 Bit 7 Bit 6...0 Bit 7 Bit 7...0 Ignore Hardware error Ignore Device not ready to received Ignore Undefined command ignore 01750153250 B BA63GV Graphic Customer Display – Operating Manual 28
Updating the Firmware/Font
Updating the Firmware
Both firmware and font can be updated via the RS232C or USB interface. Other then the pre-defined character sets, customer specific character set can be prepared upon request. When firmware or font updating is in progress, the device cannot work as a display. A Window utility is provided to perform firmware and font updating. 29 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Character Sets
Character Sets
Handling text and control sequence
Displayable Characters
The characters are displayed at the current cursor position. The cursor is moved to the next available position after displaying the character. The distance moved is dependent on the resolution of the character. The character is displayed on the beginning of next line if it can not fit on the previous line, the screen will be scrolled up one line if this happens on the last line.
Undefined Characters and Control sequence
All characters which are not included in the defined character set and all ESC sequences which have not been defined for the device are ignored by the display. A blank is displayed when data corruption occurs. 01750153250 B BA63GV Graphic Customer Display – Operating Manual 30
Character Sets
Build in character set
IBM 437 International Characters
31 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Loadable Character Sets
Thai Character Set
Character Sets 01750153250 B BA63GV Graphic Customer Display – Operating Manual 32
Character Sets
2-Byte Character Sets
The following table list the 2-byte character sets that are currently available.
font file name
GBF1616.SNI GBJ1616.SNI BIG51616.SNI KOR0816.SNI KOR1616.SNI SJIS1616.SNI
Meaning
Chinese character set GB coded Fanti style (China) Chinese character set GB coded Jianti style (China) Chinese character set BIG 5 coded Fanti style (Taiwan) Korean character set one byte codes Korean character set two byte codes Japan character set two byte codes Shift JIS coded 33 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Configuring the Device
Configuring the Device
The device can be configured as a RS232C or USB interface by setting the DIP switches as shown in the drawing below:
Dip-switch (SW1)
RS232C USB Undefined Undefined Undefined Undefined Undefined Undefined Self-test
S4
Off Off Off Off Off Off Off Off ON
S3
Off Off Off Off ON ON ON ON Off
S2
Off Off ON ON Off Off ON ON Off
S1
Off ON Off ON Off ON Off ON Off 01750153250 B BA63GV Graphic Customer Display – Operating Manual 34
Technical Data
Technical Data
Display technology
Vacuum Fluorescence Display, 256x64
Character display Character set
Character cell (W x H): 8x16 and 16x16 Height Width Row x Char ASCII 6.60 mm 3.85 mm 4 x 32 DBCS 8.25 mm 8.25 mm 4 x 16 Built-in: IBM437 + international characters Optional downloadable character sets Thai 10.45 mm 4.40 mm 3 x 32
Self-test function Interface Transmission rate Voltage supply
Possible via software control and DIP switch RS232C & USB 2.0 RS232C – baud rate up to 115.2K USB – Full speed, 12Mbps 12V +/- 10 %, 800 mA (max)
Dimension Weight
Height (with base): Width: Depth: 165 mm 206 mm 46 mm 0.5 kg 35 BA63GV Graphic Customer Display – Operating Manual 01750153250 B
Published by Wincor Nixdorf Pte Ltd 2, Kallang Sector Singapore 349277 Part No.:
01750153250 B
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement