ALL0279DSLA/ALL0279DSL

802.11g/802.11b Wireless Access Point

ADSL Modem

NAT Router

WPS

4-Port Switching Hub

Quick Install Guide

L This guide covers only the most common situations. Please refer to the full User Manual on the CD-ROM if your LAN has any of the following:

•

Router

•

Existing DHCP Server

•

PCs using Fixed (Static) IP Addresses

P/N 957YHY0030

Requirements

•

ADSL service, and an ISP account.

•

Standard Network cables.

•

TCP/IP network protocol installed on each PC.

•

Wireless Access Point requires Wireless devices compliant with the IEEE802.11b or IEEE802.11g specifications.

Setup

n

Physical Installation

1. Ensure the Wireless ADSL Router is powered OFF.

2. Use standard LAN cables to connect PCs to the LAN ports on the rear of the Wireless ADSL Router.

3. Connect the supplied ADSL cable from the ADSL port on the Wireless ADSL Router to the ADSL terminator provided by your phone company.

4. Connect the supplied power adapter to the Wireless

ADSL Router. Use only the power adapter provided. Using a different one may cause hardware damage.

Page 1

5. Check the LEDs

•

The Power LED should be ON.

•

For the LAN (PC) connection, one of the LAN LEDs should be ON (provided the PC is also ON.)

•

The ADSL LED should be ON if ADSL line is connected.

•

The Internet LED may be OFF. After configuration, it should come ON. o

Configuration

1. Start your PC. If it is already started, restart it.

It will then obtain an IP Address from the Wireless ADSL

Router's DHCP Server.

2. Start your WEB browser. In the Address box, enter the following:

HTTP://192.168.0.1

3. When prompted, use the following username and password.

•

User name: admin

•

Password: password

4. Click on the menu.

5. Step through the Wizard until finished. Refer to the data from your ISP, and the table below, to ensure your choices are correct.

Page 2

Connection Type Data required.

Dynamic IP Address Usually, none.

Specified (Fixed)

IP Address, or

IPoA (IP over ATM)

IP Address allocated to you, and related information.

PPPoE, PPPoA Login name and password.

If using a fixed IP address, the IP address and related information.

6. On the final screen of the Wizard, run the test and check that an Internet connection can be established.

If the connection fails, check both your data and the

ADSL connection

PC Setup - Windows

n

TCP/IP Setup

•

If using the default Wireless ADSL Router settings, and the default Windows TCP/IP settings, no changes need to be made.

•

If using a specified (fixed) IP address on your PC, refer to the user manual for details of the required changes:

•

The Gateway must be set to the IP address of the

Wireless ADSL Router

•

The DNS should be set to the address provided by your ISP.

Page 3

o

Internet Access

For Windows 98/ME/2000

Options .

2. Select the tab, and click the Setup button.

3. Select "I want to set up my Internet connection manually, or I want to connect through a local area network (LAN)" and click Next .

4. Select "I connect through a local area network (LAN)" and click Next .

5. Ensure all of the boxes on the following Local area network Internet Configuration screen are unchecked .

6. Check the "No" option when prompted "Do you want to set up an Internet mail account now?".

7. Click to close the Internet Connection Wizard.

Setup is now completed.

For Windows XP

Connections .

2. Select .

3. Select the tab, and click the Setup button.

4. Cancel the pop-up "Location Information" screen.

5. Click on the "New Connection Wizard" screen.

6. Select "Connect to the Internet" and click Next .

7. Select "Set up my connection manually" and click Next .

8. Check "Connect using a broadband connection that is always on" and click Next .

9. Click to close the New Connection Wizard.

Setup is now completed.

Page 4

Macintosh Setup

1. Open the TCP/IP Control Panel.

2. Select from the Connect via pop-up menu.

3. Select from the Configure pop-up menu. The DHCP Client ID field can be left blank.

4. Close the TCP/IP panel, saving your settings.

If using manually assigned IP addresses instead of DHCP, the required changes are:

•

Set the Router Address to the Wireless ADSL Router's IP

Address.

•

Ensure your DNS settings are correct.

Linux Setup using X Windows

Follow this procedure to set your system to act as a DHCP client and obtain an IP Address from the Wireless ADSL

Router:

1. Start your X Windows client.

2. Select

3. Select the "Interface" entry for your Network card. Normally, this will be called "eth0".

4. Click the button, set the "protocol" to "DHCP", and save this data.

5. To apply your changes

•

Use the "Deactivate" and "Activate" buttons

•

OR, restart your system.

Page 5

Wireless Setup

In order to use the Access Point in the Wireless ADSL Router, other Wireless devices must use the same SSID and Wireless Security settings as the Wireless ADSL Router.

The Wireless ADSL Router's default settings are as follows.

Setting Wireless ADSL Router

SSID Default

This may be changed on the Wireless screen, on the Wireless ADSL Router's main menu.

Wireless

Security

Default value: Disabled

Use the Wireless screen on the main menu to change this as required.

Ensure the Wireless ADSL Router and the other Wireless

Stations are using the same settings.

•

Use the Wireless screen to configure the Wireless Access

Point in the Wireless ADSL Router.

•

Configure the Wireless stations (PCs) using your normal method for configuring the Wireless interface.

•

Wireless Stations must also be set to use Infrastructure mode.

•

By default, the Wireless ADSL Router will automatically accept both 802.11b and 802.11g connections.

Page 6