Voyager VOM43HD User Manual

 Voyager
VOM43HD
4.3" COLOR TFT LCD 3 CAMERA MIRROR MONITOR
OWNER'S MANUAL
VOM43HD Features
High Performance Automotive Grade 4.3" Color LCD Panel
® 3 Camera Inputs
PAL/NTSC Compatible
= Mechanical Button
= Built-In Audio Speaker
= Compatible with Voyager Standard Camera
IPX6 Waterproof
Camera-Monitor Warnings!
1. Camera/monitor system aids in the use of, but does not replace
vehicle side/rear-view mirrors.
2. Objects in camera/monitor view are closer than they appear.
When backing up, proceed cautiously and be prepared to stop.
VOM43HD
Important! - Please Read This Manual Before Installing!
Congratulations on your purchase of a Voyager VOM43HD LCD Observation Monitor.
With proper installation and use, your VOM43HD LCD is designed to provide you
with years of trouble-free operation. Please read this manual thoroughly before
beginning.
All Voyager Observation products are strictly intended to be installed as supplement
aid to standard rear-view mirror systems that may already exist in your vehicle.
Voyager Observation products are not intended for use as substitutes for-view mirror
devices, or for any other standard motor vehicle equipment required to be installed
on vehicles by law.
While Voyager observation products contribute to improving the vehicle operator's
field of view, these products are no substitute for proper defensive driving techniques
and observance of traffic laws and motor vehicle safety regulations.
Warnings!
RED POWER WIRE MUST BE CONNECTED TO ACCESSORY TO AVOID CURRENT
DRAW IN THE KEY OFF POSITION.
Installation Location
It is unlawful in most jurisdictions for a person to drive a motor vehicle equipped
with a television viewer or screen located at any point forward of the back of the
driver's seat or in any location that is visible, directly or indirectly, to the driver while
operating the vehicle. The voma3HD product is designed to be used primarily as a
rear observation device in conjunction with closed circuit camera. In any installations
where the VOM43HD is used to display television broadcasts or recorded video,
playback, installation location must adhere to local laws and regulations.
Tampering
To prevent electrical shock, DO NOT OPEN THE MONITOR CASE. There are potentially
harmful voltages inside the monitor. If evidence of tampering is detected, the
warranty will be considered void and all parts will be non serviceable. There are
no user serviceable parts inside the warranty will be considered void.
Moisture
While it will withstand short periods of exposure to moisture, this product does
contain sensitive electronic components and exposure should be limited by the
user/installer. This product is not designed for locations where constant exposure
to moistureor immersion can be encountered. This unit should NEVER be cleaned
with a power washer or used where direct power washer spray may be encountered.
Depth of view
OBJECTS VIEWED ON MONITOR ARE CLOSER THAN THEY APPEAR.
PACKING CONTENTS
LCD MONITOR QTY.1
CABLE QTY.1
MACHINE SCREW QTY.4 (M4X 8MM)
CONTROLS AND OPERATION
1, POWER ON/OFF
4, SELECT
a Bh WO ND a
-Press once to turn on unit
-Press again to turn off unit
Primary Function
-Pressing ‘UP’ button increase brightness, contrast, color,
tint, volume.
-Pressing ‘DOWN’ button decrease brightness, contrast,
color, tint, volume.
Secondary Function
-While in menu modes, the ‘UP’ ‘DOWN’ are used to
select the option setting.
Primary Funtion Input Source Select
—Press 'SELECT' button sequences source input modes from CH1 to CH3.
Secondary Function Menu Option Selection
—While in menu mode, the 'SELECT' button is used to select the
highlighted function or option setting.
Primary Function Enter OSD
-Press 'MENU' button to enter the OSD
Secondary Function Return to previous menu
-While in menu modes, the MENU" button is used to return to previous menu.
MENU
У
» PRESS TO ENTER THE OSD
PRESS TO NAVIGATE UP/DOWN
PRESS TO SET UP EACH MENU
PRESS TO SET EACH SETTING OPTION
PRESS TO ADJUST THE NUMBER
PRESS TO CONFIRM THE SETTING
PRESS ME FOR PREVIOUS MENU
У
PICTURE
PICTURE
BRIGHTNESS 1TO10
| CONTRAST 1TO10
COLOR 1 ТО 10
TINT 1TO 10
VOLUME
VOLUME ОТО 100
BC VOLUME 0TO 100
PRESS TO SET EACH SETTING OPTION
PRESS TO ADJUST THE NUMBER
PRESS TO CONFIRM THE SETTING
PRESS | = | FOR PREVIOUS MENU
TRIGGER
PRESS TO SET EACH SETTING OPTION
PRESS TO SELECTEACH SETTING OPTION
PRESS TO CONFIRM THE SETTING
"FOR PREVIOUS MENU
CAM1 1 TO 10
CAM2 1 TO 10
>», CAM3 1 TO 10
MARKER ON,OFF
SCALE
SETTING
VIDEO AUTO,NTSC,PAL
SCAN OFF,ON
У
SCEEN SAVER OFF,10,20,60
PRESS TO SET EACH SETTING OPTION
PRESS TO SELECT EACH SETTING OPTION
PRESS TO CONFIRM THE SETTING
PRESS = | FOR PREVIOUS MENU
AUTOPOWER ON,OFF
SCAN
CAM1 1 TO 10
CAM2 1 TO 10
>| CAM3 1 TO 10
PRESS TO SET EACH SETTING OPTION
PRESS TO ADJUST THE NUMBER
PRESS TO CONFIRM THE SETTING
| Dress | = | FOR PREVIOUS MENU
CAMERA
CAM1 NORMAL, MIRROR, OFF
CAM2 NORMAL, MIRROR, OFF
У
CAM3 NORMAL, MIRROR, OFF
MISCELLANEOUS
PRESS TO SET EACH SETTING OPTION
PRESS TO SELECTEACH SETTING OPTION
PRESS TO CONFIRM THE SETTING
PRESS TO SET THE LANGUAGE
LANGUAGE ENGLISH, FRANGAIS
, ESPAGNOL
У
RESET
—» PRESS ‘RESET TO RESET THE SYSTEM
VOM43HD
INSTALLATION INSTRUCTIONS
BEFORE YOU BEGIN INSTALLATION:
Before drilling be sure that no cable or wiring is on the other side. Clamp all wires
securely to reduce the possibility of them being damaged during installation and use.
Keep all cables away from hot or moving parts, and electrically noisy components.
Wiring Definitions:
=u Power connection: Pin1 POWER IN DC (12V- 24 V) -Red
Pin 2 GROUND -Black
Pin 3 CHANNEL 1 TRIGGER -Blue
Pin 4 CHANNEL 2 TRIGGER -Brown
Pin 5 CHANNEL 3 TRIGGER -Green
= Camera 1 input: 4-Pin Connection for camera or camera extension cable
= Camera 2 input: 4-Pin Connection for camera or camera extension cable
m Camera 3 input: 4-Pin Connection for camera or camera extension cable
= LCD panel: 13-Pin Large DIN cable connection to monitor
General:
1. Choose the monitor and camera locations.
2. Install all required cables in vehicle. A 3/4"(19mm) hole should be drilled for
passing camera cables through vehicle wall , barriers, etc.
Install split grommets where applicable. If additional cable protection is
required install convoluted tubing over the cable.
3. After cable/wiring has been routed and components in place, temporarily
make all system connections and perform a system function check. If system
does not operate properly, see the troubleshooting section regarding cable.
4. Make sure all cables are routed away from hot or moving parts, and away from
sharp edges. Secure cables with wire ties.
Backup (Rear) Camera
® Rear-mounted camera used for monitoring while backing up must be connected
to the CAM1 input . Trigger! must be connected to the reverse gear light circuit.
Side Camera
The side mounted camera should be connected to the CAM2 and CAM3 inputs.
Trigger lines 2 and 3 should be connected to the vehicle's turn signal circuits.
TYPICAL SYSTEM CONNECTTION
CAMERA X3
4-PIN FEMALE CAMERA
CONNECTOR
a
C
y
o o
a
a
CAM3 CAM2 CAM1
|
VOM43HD
13-PIN LARGE DIN CONNECTOR
_ | (MALE)
13-PIN LARGE DIN CONNECTOR
(FEMALE)
POWER/TRIGGERWIRE FUNCTIONS
Df refe | WIRECOLOR DESCRIPTION
1 |RED POWER IN DC 12-DC24V
2 | BLACK GROUND
3 | BLUE TRIGGER1 (CAM1)
4 | BROWN TRIGGER2 (CAM2)
HU 5 | GREEN TRIGGER3 (CAM3)
VOM43HD
PRODUCT SPECIFICATIONS
LCD PANEL SPECIFICATIONS
Size/Type 4.3"(Digital) TFT LCD
Brightness 400 cd/m’ (typ)
Contrast Ratio | 500
View Angles Top (12 O'clock) 50° (typ)
Bottom (6 O'clock) 70° (typ)
(@CR21 0)
Horizontal 70° (typ)
15ms
Response Time
20ms
Back Light Type | LED
Back Light Life
50,000 hrs (min)
0 Operation Temperature Range : -20°C~+70°C
oa Storage Temperature Range : -30° C—+80° C
a Max Humidity : 85%
a Operation Voltage Range : DC12V-24V
= Current Draw (typical) :337mA@12VDC
a Signal system : NTSC or PAL (Auto detection)
= Video
= Audio
Aspect Ratio: 16:9
Input Level: 1Vp-p 750
Input Level : 150mV(Max)
a Product Dimensions :5.90W x 3.78H x 1.09D (Inches)
a Product Weight : 2.65 Ibs/1200g
SS
ELECTRONICS.
www.asaelectronics.com