BenQ TH685 PROJECTOR User Manual


Add to my manuals
56 Pages

advertisement

BenQ TH685 PROJECTOR User Manual | Manualzz
Digital Projector
User Manual
Home Entertainment Series I TH685
V 1.00
Warranty and Copyright information
Limited warranty
BenQ warrants this product against any defects in material and workmanship, under normal usage and
storage.
Proof of purchase date will be required with any warranty claim. In the event this product is found to be
defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be
replacement of any defective parts (labor included). To obtain warranty service, immediately notify the
dealer from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in accordance
with BenQ's written instructions, especially the ambient humidity must be in-between 10% and 90%,
temperature in-between 0°C and 35°C, altitude lower than 4920 feet, and avoiding to operate the
projector in a dusty environment. This warranty gives you specific legal rights, and you may have other
rights which vary from country to country.
For other information, please visit www.BenQ.com.
Copyright
Copyright © 2019 by BenQ Corporation. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of BenQ Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with respect
to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation to notify any person of such
revision or changes.
*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others are
copyrights of their respective companies or organizations.
Patents
Please go to http://patmarking.benq.com/ for the details on BenQ projector patent coverage.
2
Warranty and Copyright information
Table of Contents
Warranty and Copyright information ................................................................................ 2
Important safety instructions .............................................................................................. 4
Introduction .......................................................................................................................... 7
Shipping contents ....................................................................................................................................... 7
Projector exterior view ............................................................................................................................ 8
Controls and functions.............................................................................................................................. 9
Positioning your projector ................................................................................................. 11
Choosing a location ................................................................................................................................. 11
Obtaining a preferred projected image size....................................................................................... 12
Mounting the projector .......................................................................................................................... 13
Adjusting the projected image .............................................................................................................. 14
Connection .......................................................................................................................... 16
Connecting smart devices ...................................................................................................................... 17
Operation ............................................................................................................................ 18
Starting up the projector ........................................................................................................................ 18
Using the menus ....................................................................................................................................... 20
Securing the projector ............................................................................................................................ 21
Switching input signal ............................................................................................................................... 23
Shutting down the projector ................................................................................................................. 23
Direct power off ...................................................................................................................................... 23
Menu operation ................................................................................................................... 24
Menu System ............................................................................................................................................. 24
Basic menu ............................................................................................................................................... 29
Advanced menu ..................................................................................................................................... 31
Maintenance ........................................................................................................................ 40
Care of the projector .............................................................................................................................. 40
Lamp information ..................................................................................................................................... 41
Troubleshooting ................................................................................................................. 47
Specifications ...................................................................................................................... 48
Projector specifications .......................................................................................................................... 48
Dimensions ................................................................................................................................................ 49
Timing chart............................................................................................................................................... 50
RS232 command ....................................................................................................................................... 53
Table of Contents
3
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information technology
equipment. However, to ensure safe use of this product, it is important that you follow the instructions
mentioned in this manual and marked on the product.
1. Please read this manual before you
operate your projector. Save it for future
reference.
2. Do not look straight at the projector
lens during operation. The intense light
beam may damage your eyes.
3. Refer servicing to qualified service
personnel.
6. In some countries, the line voltage is NOT
stable. This projector is designed to operate
safely within a mains voltage between 100 to
240 volts AC, but could fail if power cuts or
surges of ±10 volts occur. In areas where
the mains voltage may fluctuate or cut
out, it is recommended that you
connect your projector through a power
stabilizer, surge protector or
uninterruptible power supply (UPS).
7. Do not block the projection lens with any
objects when the projector is under
operation as this could cause the objects to
become heated and deformed or even cause a
fire. To temporarily turn off the lamp, use the
blank function.
4. Always open the lens shutter (if any) or
remove the lens cap (if any) when the
projector lamp is on.
5. The lamp becomes extremely hot during
operation. Allow the projector to cool for
approximately 45 minutes prior to removing
the lamp assembly for replacement.
4
Important safety instructions
8. Do not operate lamps beyond the rated lamp
life. Excessive operation of lamps beyond the
rated life could cause them to break on rare
occasions.
13. Always place the projector on a level,
9. Never replace the lamp assembly or any
horizontal surface during operation.
electronic components unless the projector is
unplugged.
- Do not use if tilted at an angle of more than 10
degrees left to right, nor at angle of more than 15
degrees front to back. Using the projector when it is
not fully horizontal may cause a malfunction of, or
damage to, the lamp.
10. Do not place this product on an unstable cart,
stand, or table. The product may fall,
14. Do not stand the projector on end vertically.
sustaining serious damage.
Doing so may cause the projector to fall over,
causing injury or resulting in damage to the
projector.
11. Do not attempt to disassemble this projector.
There are dangerous high voltages inside
which may cause death if you should come
into contact with live parts. The only user
15. Do not step on the projector or place any
serviceable part is the lamp which has its own
objects upon it. Besides probable physical
removable cover.
damage to the projector, doing so may result
in accidents and possible injury.
Under no circumstances should you ever
undo or remove any other covers. Refer
servicing only to suitably qualified professional
service personnel.
12. Do not block the ventilation holes.
- Do not place this projector on a blanket, bedding or
any other soft surface.
- Do not cover this projector with a cloth or any other
item.
- Do not place inflammables near the projector.
16. When the projector is under operation, you
may sense some heated air and odor from its
ventilation grill. It is a normal phenomenon
and not a product defect.
If the ventilation holes are seriously
obstructed, overheating inside the projector
may result in a fire.
Important safety instructions
5
17. Do not place liquids near or on the projector.
Liquids spilled into the projector may cause it
to fail. If the projector does become wet,
disconnect it from the power supply's power
outlet and call BenQ to have the projector
serviced.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C /
104°F
- Locations where the altitudes are higher than 3000 m
(10000 feet).
3000 m
(10000 feet)
0m
(0 feet)
Risk Group 2
18. This product is capable of displaying inverted
images for ceiling/wall mount installation.
1. According to the classification of
photobiological safety of lamps and lamp
systems, this product is Risk Group 2, IEC
62471-5:2015.
2. Possibly hazardous optical radiation emitted
from this product.
19. This apparatus must be earthed.
3. Do not stare at operating lamp. May be
harmful to the eyes.
20. Do not place this projector in any of the
following environments.
4. As with any bright source, do not stare into
the direct beam.
- Space that is poorly ventilated or confined. Allow at
least 50 cm clearance from walls and free flow of air
around the projector.
- Locations where temperatures may become
excessively high, such as the inside of a car with all
windows rolled up.
- Locations where excessive humidity, dust, or cigarette
smoke may contaminate optical components, shorten
the projector's life span and darken the image.
Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.
To avoid damaging the DLP chips, never aim a high-power laser beam into the projection lens.
6
Important safety instructions
Introduction
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these items are missing,
please contact your place of purchase.
Standard accessories
Projector
Remote control with
batteries
Quick start guide
Warranty card*
Power cord
VGA cable
• The supplied accessories will be suitable for your region, and may differ from those illustrated.
• *The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.
Optional accessories
1. Spare lamp kit
3. QCast Mirror dongle (QP20)
2. 3D glasses
Replacing the remote control batteries
1. Press and slide off the battery cover, as illustrated.
2. Remove the old batteries (if applicable) and install two
AAA batteries. Make sure that the positive and negative
ends are positioned correctly, as illustrated.
3. Slide the battery cover in until it clicks into place.
• Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen,
bathroom, sauna, sunroom or in a closed car.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for
your region.
• Never throw the batteries into a fire. There may be danger of an explosion.
• If the batteries are dead or if you will not be using the remote control for an extended period of time, remove the
batteries to avoid damage to the remote control from possible battery leakage.
Introduction
7
Projector exterior view
6
1
7
8
2
9
3
4
5
10
11
12
13
14
15
16
3
19
19
19
3
3
17
1. Focus ring and Zoom ring
11. HDMI 2 input port
2. Vent (air exhaust)
12. HDMI 1 input port
3. Adjuster feet
13. USB Type A port
4. Projection lens
14. RGB (PC) signal input jacks
5. IR remote sensor
15. RGB (PC) signal output jack
6. External control panel
(See Controls and functions on page 9.)
16. RS-232 control port
7. Lamp cover
18. Kensington anti-theft lock slot
8. Ambient Light Sensor (ALS)
19. Ceiling mount holes
9. Vent (air inlet)
10. Audio input jacks
Audio output jack
8
Introduction
17. AC power jack
18
Controls and functions
Projector & Remote control
All the key presses described in this document
are available on the remote control or projector.
1
2
5
6
7
3
4
8
9
10
1
16
11
12
5
8
4
6
10
13
17
14
7
15
1.
POWER
Toggles the projector between standby mode
and on.
ON/
Off
Toggles the projector between standby mode
and on.
2. POWER indicator light/TEMPerature
warning light/LIGHT indicator light
(See Indicators on page 46.)
5. Arrow keys ( ,
,
,
)
When the On-Screen Display (OSD) menu is
activated, these keys are used as directional
arrows to select the desired menu items and
to make adjustments.
Keystone keys (
,
)
Displays the keystone correction page.
Volume keys
/
Decreases or increase the projector volume.
3. IR remote sensor
4. BACK
Goes back to previous OSD menu, exits and
saves menu settings.
Introduction
9
12. PIC MODE
6. SOURCE
Selects the picture mode.
Displays the source selection bar.
7. ECO BLANK
Used to hide the screen picture.
Do not block the projection lens from
projecting as this could cause the blocking
object to become heated and deformed or
even cause a fire.
8. OK
Confirms the selected On-Screen Display
(OSD) menu item.
9. AUTO
13.
Toggles projector audio between on and off.
14. MHL Zone
This model does not support MHL functions.
15. SOUND MODE
Selects the sound mode.
16. LUMIEXPERT BOOST
Displays the LumiExpert Boost menu.
17. Volume keys
/
Automatically determines the best picture
timings for the displayed image when PC signal
Decreases or increases the projector volume.
(analog RGB) is selected.
10. MENU
Turns on the On-Screen Display (OSD) menu.
11.
Displays the keystone menu.
Remote control effective range
The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR
remote control sensor(s) to function correctly. The distance between the remote control and the
sensor(s) should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensor(s) on the
projector that might obstruct the infra-red beam.
• Operating the projector from the front
• Operating the projector from the top
Ap
Ap
10
pro
x. +
3
Introduction
0º
pro
x. +
3 0º
Positioning your projector
Choosing a location
Before choosing an installation location for your projector, take the following factors into consideration:
• Size and position of your screen
• Electrical outlet location
• Location and distance between the projector and the rest of your equipment
You can install your projector in the following ways.
1. Front
2. Rear
Select this location with the projector placed on
the table in front of the screen. This is the most
common way to position the projector for quick
setup and portability.
Select this location with the projector placed on
the table behind the screen. Note that a special
rear projection screen is required.
3. Front Ceiling
4. Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the
screen. Purchase the BenQ Projector Ceiling
Mount Kit from your dealer to mount your
projector on the ceiling.
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
BenQ Projector Ceiling Mount Kit are required
for this installation location.
After turning on the projector, go to Basic Menu - Settings > Projector Installation, press OK
and press / to select a setting.
You can also use QUICK INSTALL on the remote control to access this menu.
Positioning your projector
11
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting (if available), and the video format
each factors in the projected image size.
Projection dimensions
16:9 Screen diagonal
Screen
Center of lens
H
W
Projection distance
• The screen aspect ratio is 16:9 and the projected picture is in a 16:9 aspect ratio
Screen size
Diagonal
12
Projection Distance (mm)
H (mm)
W (mm)
762
374
664
748
859
970
19
40
1016
498
886
998
1145
1293
25
50
1270
623
1107
1247
1432
1616
31
60
1524
747
1328
1497
1718
1939
37
70
1778
872
1550
1746
2004
2263
44
80
2032
996
1771
1996
2291
2586
50
90
2286
1121
1992
2245
2577
2909
56
100
2540
1245
2214
2495
2864
3232
62
110
2794
1370
2435
2744
3150
3555
68
120
3048
1494
2657
2994
3436
3879
75
130
3302
1619
2878
3243
3723
4202
81
140
3556
1743
3099
3493
4009
4525
87
150
3810
1868
3321
3742
4295
4848
93
160
4064
1992
3542
3992
4582
5171
100
170
4318
2117
3763
4241
4868
5495
106
180
4572
2241
3985
4491
5154
5818
112
190
4826
2366
4206
4740
5441
6141
118
200
5080
2491
4428
4990
5727
6464
125
210
5334
2615
4649
5239
6013
6788
131
220
5588
2740
4870
5489
6300
7111
137
230
5842
2864
5092
5738
6586
7434
143
240
6096
2989
5313
5988
6873
7757
149
250
6350
3113
5535
6237
7159
8080
156
260
6604
3238
5756
6487
7445
8404
162
270
6858
3362
5977
6736
7732
8727
168
280
7112
3487
6199
6986
8018
9050
174
290
7366
3611
6420
7235
8304
9373
181
300
7620
3736
6641
7485
8591
9696
187
Inch
mm
30
Positioning your projector
Average
Max distance
(with min zoom)
Offset
(mm)
Min distance
(with max zoom)
For example, if you are using a 120-inch screen, the recommended projection distance in the "Average"
column is 3436 mm.
If your measured projection distance is 3700 mm, the closest match in the "Average" column is 3723
mm. Looking across this row shows that a 130'' (about 3.3 m) screen is required.
To optimize your projection quality, we suggest to do the projection within non-gray area.
All measurements are approximate and may vary from the actual sizes.
BenQ recommends that if you intend to permanently install the projector, you should physically test the projection
size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this
projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your
installation location.
Mounting the projector
If you intend to mount your projector, we strongly recommend that you use a proper fitting BenQ
projector mounting kit and that you ensure it is securely and safely installed.
If you use a non-BenQ brand projector mounting kit, there is a safety risk that the projector may fall
down due to an improper attachment through the use of the wrong gauge or length screws.
Before mounting the projector
• Purchase a BenQ projector mounting kit from the place you purchased your BenQ projector.
• BenQ recommends that you also purchase a separate Kensington lock compatible security cable and
attach it securely to both the Kensington lock slot on the projector and the base of the mounting
bracket. This will perform the secondary role of restraining the projector should its attachment to the
mounting bracket become loose.
• Ask your dealer to install the projector for you. Installing the projector on your own may cause it to
fall and result in injury.
• Take necessary procedures to prevent the projector from falling off such as during an earthquake.
• The warranty doesn’t cover any product damage caused by mounting the projector with a non-BenQ
brand projector mounting kit.
• Consider the surrounding temperature where the projector is ceiling/wall mounted. If a heater is used,
the temperature around the ceiling may be higher than expected.
• Read the user manual for the mounting kit about the range of torque. Tightening with torque
exceeding the recommended range may cause damage to the projector and subsequently falling off.
• Make sure the power outlet is at an accessible height so that you can easily shut down the projector.
Positioning your projector
13
Ceiling/Wall mount installation diagram
Ceiling/Wall mount screw: M4
(Max L = 25 mm; Min L = 20 mm)
60
65.89
65.89
40.27
113.54
Unit: mm
Adjusting the projected image
Adjusting the projection angle
If the projector is not placed on a flat surface or the screen
and the projector are not perpendicular to each other, the
projected image becomes trapezoidal. You can adjust the
adjuster feet to fine-tune the horizontal angle.
To retract the feet, screw the adjuster feet in a reverse
direction.
Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press AUTO. Within 3
seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and
Clock to provide the best picture quality.
The current source information will be displayed in the corner of the screen for 3 seconds.
This function is only available when PC signal (analog RGB) is selected.
14
Positioning your projector
Fine-tuning the image size and clarity
Adjust the projected image to the size that you
need using the zoom ring.
Sharpen the image by rotating the focus ring.
Correcting keystone
Keystoning refers to the situation where the projected image becomes a trapezoid due to angled
projection.
To correct this, you will need to manually correct it following these steps.
1. Do one of the following steps to display the keystone
correction page.
• Press
• Press
/
on the projector.
on the remote control.
Press
.
Press
.
2. After the Keystone correction page displays. Press
to correct keystoning at the top of the
image. Press
to correct keystoning at the bottom of the image.
Positioning your projector
15
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
Notebook or
desktop computer
A/V device
5
3
4
6
1
Monitor
1
2
1
VGA cable
2
VGA to DVI-A cable
3
Component Video to VGA
(D-Sub) adapter cable
4
HDMI cable
5
Audio cable
6
HDMI wireless dongle
7
USB cable (A to Micro B
type) connect to the power
port of HDMI wireless
dongle.
7
5
Speakers
Smart device
• In the connections above, some cables may not be included with the projector (see Shipping contents on page 7).
They are commercially available from electronics stores.
• The connection illustrations are for reference only. The rear connecting jacks available on the projector vary with
each projector model.
• Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo
like FN + function key with a monitor symbol turns the external display on/off. Press FN and the labeled
function key simultaneously. Refer to your notebook's documentation to find your notebook's key
combination.
• If the selected video image is not displayed after the projector is turned on and the correct video source has been
selected, check that the video source device is turned on and operating correctly. Also check that the signal
cables have been connected correctly.
16
Connection
You need only connect the projector to a video source device using just one of the connecting methods,
however each provides a different level of video quality.
Terminal
HDMI
Component Video (through RGB
input)
Picture quality
Best
Better
Connecting audio
The projector has built-in mono speaker(s) which are designed to provide basic audio functionality
accompanying data presentations for business purposes only. They are not designed for, nor intended
for stereo audio reproduction use as might be expected in home theater or home cinema applications.
Any stereo audio input (if provided), is mixed into a common mono audio output through the projector
speaker(s).
The built-in speaker(s) will be muted when the AUDIO OUT jack is connected.
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected.
• If the selected video image is not displayed after the projector is turned on and the correct video source has been
selected, check that the video source device is turned on and operating correctly. Also check that the signal
cables have been connected correctly.
Connecting smart devices
The projector can project the content directly from a smart device by using a wireless dongle.
HDMI wireless dongle (e.g. BenQ QCast Mirror)
Connect the dongle to HDMI and USB TYPE-A ports on the projector and switch the input signal to
HDMI 1 or HDMI 2.
Connection
17
Operation
Starting up the projector
1. Plug the power cord. Turn on the power outlet switch
(where fitted). The power indicator on the projector
lights orange after power has been applied.
2. Press
on the projector or
on the remote
control to start the projector. The power indicator
flashes green and stays green when the projector is on.
The start up procedure takes about 30 seconds. In the
later stage of start up, a startup logo is projected.
(If necessary) Rotate the focus ring to adjust the image
clearness.
3. If this is the first time you turn on the projector, the setup wizard appears to guide you through
setting up the projector. If you have already done this, skip this step and move on to step 5.
•
Use the arrow keys (
/
/ / ) on the projector or remote control to move through the menu items.
•
Use OK to confirm the selected menu item.
The Setup Wizard screenshots below are for reference only and may differ from the actual design.
Step 1:
Specify Projector Position.
For more information about projector
position, see Choosing a location.
Step 2:
Specify OSD Language.
Step 3:
Specify Auto Vertical Keystone.
For more information about vertical
keystone, see Correcting keystone.
18
Operation
Step 4:
Specify Auto Source.
Select On if you want the projector to
always search for available signals
automatically when the projector is turned
on.
Step 5:
Specify Menu Type.
For more information about menu types,
see Using the menus.
Now you’ve completed the initial setup.
4. If you are prompted for a password, press the arrow keys to enter a 6-digit password. See Utilizing
the password function on page 21.
5. Switch all of the connected equipment on.
6. The projector will search for input signals. The current input signal being scanned appears. If the
projector does not detect a valid signal, the message “No Signal” will continue displaying until an
input signal is found.
You can also press SOURCE to select your desired input signal. See Switching input signal on page
23.
• Please use the original accessories (e.g. power cord) to avoid possible dangers such as electric shock and fire.
• If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before
energizing the lamp.
• The Setup Wizard screenshots are for reference only and may differ from the actual design.
• If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message
“Out of Range” displayed on the background screen. Please change to an input signal which is compatible
with the projector's resolution or set the input signal to a lower setting. See Timing chart on page 50.
• If no signal is detected for 3 minutes, the projector automatically enters saving mode.
• If “Reset All Settings” is selected, setup wizard will appear after reboot, and Auto Source will be reset to default
value.
Operation
19
Using the menus
The projector is equipped with 2 types of On-Screen Display (OSD) menus for making various
adjustments and settings.
• Basic OSD menu: provides primary menu functions. (See Basic menu on page 29)
• Advanced OSD menu: provides full menu functions. (See Advanced menu on page 31)
To access the OSD menu, press MENU on the projector or remote control.
• Use the arrow keys ( / / / ) on the projector or remote control to move through the menu items.
• Use OK on the projector or remote control to confirm the selected menu item.
The first time you use the projector (after finishing the initial setup), Basic OSD menu displays.
The OSD screenshots below are for reference only, and may differ from the actual design.
Below is the overview of the Basic OSD menu.
• Input signal connected
• No input signal connected
Picture Mode
Bright
Wall Color
Projector Position
Off
Front
Menu Type
Auto Source
Sound Mode
Standard
Volume
Test Pattern
Off
HDMI Range
On
Basic
Auto
Reset Light Timer
Reset All Settings
Information
10
Mute
Off
Fast Mode
Off
3D Mode
3D Off
3D Sync Invert
Press OK
Settings
Press OK
If you intend to switch from the Basic OSD menu to the Advanced OSD menu, follow the
instructions below:
1. Go to Basic Menu - Settings > Menu Type and press OK.
2. Press /
menu.
to select Advanced and press OK. Your projector will switch to Advanced OSD
Below is the overview of the Advanced OSD menu.
Main menu icon
Main menu name
Picture
Picture Mode
Selection bar
Submenu
Vivid TV
User Mode Management
Brightness
50
Contrast
50
Color
50
Tint
50
Sharpness
Status
7
Advanced...
Reset Current Picture Mode
Current input source
20
Operation
PC
Exit
Press BACK to go back to
the previous window or to
exit.
Likewise, when you wish to switch from the Advanced OSD menu to the Basic OSD menu, follow
the instructions below:
1. Go to Advanced Menu - System Setup : Basic > Menu Settings and press OK.
2. Highlight Menu Type and press
OSD menu.
/
to select Basic. Your projector will switch to the Basic
Securing the projector
Using a security cable lock
The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock, such as
the Kensington lock, to secure the projector. You can locate a Kensington lock slot on the rear side of
the projector. See item 18 on page 8.
A Kensington security cable lock is usually a combination of key(s) and the lock. Refer to the lock’s
documentation for finding out how to use it.
Utilizing the password function
Setting a password
1. Go to Advanced Menu - System Setup : Advanced > Password. Press OK. The Password
page appears.
2. Highlight Change Password and press OK.
3. The four arrow keys ( , , , ) respectively represent
4 digits (1, 2, 3, 4). According to the password you desire
to set, press the arrow keys to enter six digits for the
password.
4. Confirm the new password by re-entering the new
password.
Once the password is set, the OSD menu returns to the
Password page.
Input New Password
Return
5. To activate the Power On Lock function, press / to
highlight Power On Lock and press / to select On. Input the password again.
• The digits being input will display as asterisks on-screen. Make a note of your selected password and keep it in a
safe place in advance or right after the password is entered so that it is available to you should you ever
forget it.
• Once a password has been set and the power on lock is activated, the projector cannot be used unless the
correct password is entered every time the projector is started.
If you forget the password
If you enter the wrong password, the password error message will appear, and the Input Current
Password message follows. If you absolutely do not remember the password, you can use the
password recall procedure. See Entering the password recall procedure on page 22.
•
Under the Advanced OSD menu
Password Error
Please try again.
•
Under the Basic OSD menu
Password Error
Please try again.
Operation
21
If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a
short time.
Entering the password recall procedure
1. Press and hold AUTO for 3 seconds. The projector will display a coded number on the screen.
•
Under the Advanced OSD menu
•
Under the Basic OSD menu
Recall Password
Recall Password
Please write down the recall code,
and contact BenQ
Customer Center.
Please write down the recall code, and contact
BenQ Customer Center.
Recall code:
Recall code:
XXX XXX XXX XXX
XXX XXX XXX XXX
Exit
2. Write down the number and turn off your projector.
3. Seek help from the local BenQ service center to decode the number. You may be required to
provide proof of purchase documentation to verify that you are an authorized user of the
projector.
Changing the password
1. Go to Advanced Menu - System Setup : Advanced > Password. Press OK. The Password
page appears.
2. Highlight Change Password and press OK. The message “Input Current Password” appears.
3. Enter the old password.
• If the password is correct, another message “Input New Password” appears.
• If the password is incorrect, the password error message will appear, and the message “Input
Current Password” appears for your retry. You can press BACK to cancel the change or try
another password.
4. Enter a new password.
5. Confirm the new password by re-entering the new password.
Disabling the password function
To disable password protection, go to Advanced Menu - System Setup : Advanced > Password >
Power On Lock and press / to select Off. The message “Input Current Password” appears.
Enter the current password.
• If the password is correct, the OSD menu returns to the Security Settings page. You will not
have to enter the password next time turning on the projector.
• If the password is incorrect, the password error message will appear, and the message “Input
Current Password” appears for your retry. You can press BACK to cancel the change or try
another password.
Though the password function is disabled, you need to keep the old password in hand should you ever need to
re-activate the password function by entering the old password.
22
Operation
Switching input signal
The projector can be connected to multiple devices at the same time.
However, it can only display one full screen at a time. When starting up,
the projector automatically searches for the available signals.
Be sure the Advanced Menu - System Setup : Basic > Auto Source
menu is On if you want the projector to automatically search for the
signals.
Source
HDMI 1
HDMI 2
To select the source:
1. Press SOURCE. A source selection bar appears.
2. Press
/
PC
until your desired signal is selected and press OK.
Once detected, the selected source information will appear at the corner of the screen for seconds.
If there is multiple equipment connected to the projector, repeat steps 1-2 to search for another
signal.
• The brightness level of the projected image will change accordingly when you switch between different input
signals.
• For best display picture results, you should select and use an input signal which outputs at the projector’s native
resolution. Any other resolutions will be scaled by the projector depending upon the “aspect ratio” setting,
which may cause some image distortion or loss of picture clarity. See Aspect Ratio on page 36.
Shutting down the projector
1. Press
on the projector or
on the remote control
and a confirmation message will appear prompting you. If
you don't respond in a few seconds, the message will
disappear.
2. Press
or
a second time. The power indicator
flashes orange, the projection lamp shuts down, and the
fans will continue to run for approximately 90 seconds to
cool down the projector.
3. Once the cooling process finishes, the power indicator
becomes a steady orange and fans stop. Disconnect the
power cord from the power outlet.
• To protect the lamp, the projector will not respond to any commands during the cooling process.
• To shorten the cooling time, you can also activate the Quick cooling function. See Quick Cooling on page 38.
• Avoid turning on the projector immediately after turning it off as excessive heat may shorten lamp life.
• Lamp life results will vary depending on environmental conditions and usage.
Direct power off
The AC power cord can be pulled out right after the projector is turned off. To protect the lamp, wait
about 10 minutes before re-starting the projector. If you attempt to re-start the projector, the fans may
run for a few minutes to cool down. In such cases, press
the fans stop and the power indicator turns orange.
or
again to start the projector after
Operation
23
Menu operation
Please note that the on-screen display (OSD) menus vary according to the signal type selected and the
projector model you are using.
The menu items are available when the projector detects at least one valid signal. If there is no
equipment connected to the projector or no signal detected, limited menu items are accessible.
Menu System
Basic Menu
Sub-menu
Picture Mode
Sound Mode
Volume
Mute
Fast Mode
3D Mode
3D Sync Invert
Settings
24
Menu operation
Options
Bright/Living Room/Cinema/Sports/Game/
User 1/User 2/(3D)/HDR10/HLG
Standard/Cinema/Music/Game/Sport/User
0~10~20
On/Off
On/Off
Auto/3D Off/Frame Sequential/
Frame Packing/Top-Bottom/Side-by-Side
Advanced Menu
Main menu
Sub-menu
Picture Mode
User Mode
Management
Brightness
Contrast
Color
Tint
Sharpness
PICTURE
Advanced
Reset Current
Picture Mode
Options
Bright/Living Room/Cinema/Sports/
Game/User 1/User 2/(3D)/HDR10/
HLG
Bright/Living Room/Cinema/Sports/
Game/User 1/User 2
Rename User Mode
0~50~100
0~50~100
0~50~100
0~50~100
0~7~15
Gamma
1.6/1.8/2.0/2.1/2.2/2.3/2.4/2.6/2.8/
Selection
BenQ
HDR Brightness -2~0~2
Preset (Normal/Cool/Lamp Native/
Warm)
Red Gain (0~200)
Green Gain (0~200)
Color
Temperature
Blue Gain (0~200)
Red Offset (0~511)
Green Offset (0~511)
Blue Offset (0~511)
Primary Color (Red/Green/Blue/
Cyan/Magenta/Yellow/White)
Color
Hue (0~200~400)
Management
Saturation (0~200~400)
Gain (0~200~400)
Noise
0~31
Reduction
Brilliant Color 0~10
Fast Mode
On/Off
LumiExpert (On/Off)
Level (-2~0~2)
LumiExpert
Manual Calibration (Manual
Calibration Status/Calibrate/
Reset Manual Calibration)
Normal/Economic/SmartEco/
Light Mode
LampSave
Reset/Cancel
Menu operation
25
Main menu
Sub-menu
Sound Mode
Effect Mode
User EQ
SOUND
Mute
Volume
Power On/Off
Ring Tone
Reset Audio
Settings
Aspect Ratio
On/Off
Reset/Cancel
Auto/4:3/16:9/16:10
Off/Light Yellow/Pink/
Light Green/Blue
Wall Color
DISPLAY
Image Position
Overscan
Adjustment
PC &
Component
YPbPr Tuning
3D
HDR
Digital Lens
Shift
26
Menu operation
Options
Standard/Cinema/Music/Game/
Sport/User
100Hz/300Hz/1kHz/3kHz/10kHz
On/Off
0~10~20
0~1~3
3D Mode
H. Size
Phase
Auto
Auto/3D Off/Frame Sequential/
Frame Packing/Top-Bottom/
Side-by-Side
3D Sync Invert
Auto/Off
-20~0~20
Main menu
Sub-menu
Options
Language
Background Color
Splash Screen
Projector Position
SYSTEM SETUP:
Auto Off
BASIC
Direct Power On
Menu Type
Menu Position
Menu Settings Menu Display
Time
Blank Reminder
Message
Source Rename
Auto Source
Reset Light
Timer
Light Settings
Light Usage
Time
HDMI Range
HDMI Settings
HDMI EDID
Baud Rate
SYSTEM SETUP:
Test Pattern
ADVANCED
Quick Cooling
High Altitude Mode
Change
Password
Password
Power On Lock
Key Lock
LED Indicator
Reset All Settings
Black/Blue/Purple
BenQ/Black/Blue
Front/Front Ceiling/Rear
Rear Ceiling
Disable/5 min/10 min/15 min/
20 min/25 min/30 min
On/Off
Basic/Advanced
Center/Top-Left/Top-Right/
Bottom-Right/Bottom-Left
Always On/5 sec/10 sec/15 sec/
20 sec/25 sec/30 sec
On/Off
On/Off
Reset/Cancel
Auto/Full/Limited
HDMI 1/HDMI 2
(Enhanced/Standard)
9600/14400/19200/38400/57600/
115200
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
Reset/Cancel
Menu operation
27
Main menu
INFORMATION
28
Menu operation
Sub-menu
Source
Picture Mode
Resolution
Color System
Light Usage Time
3D Format
Firmware Version
Service Code
Options
Basic menu
The projector is preset with several predefined picture modes so that you can
choose one to suit your operating environment and input signal picture type.
• Bright: Maximizes the brightness of the projected image. This mode is suitable
for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
• Living Room: Being slightly brighter than Cinema mode, it is suitable for
playing movies in rooms where there is a small amount of ambient light, eg. your
living room.
Picture Mode
• Cinema: With well-balanced color saturation and contrast with a low brightness
level, this is most suitable for enjoying movies in a totally dark environment (as
you would find in a commercial cinema).
• Sports: This mode is best for watching sporting events in rooms where is a small
amount of ambient light, et. your living room.
• Game: This mode is best for playing video games in rooms where there is a small
amount of ambient light, eg. your living room.
• User 1/User 2: Recalls the settings customized based on the current available
picture modes. See User Mode Management on page 32.
• HDR10/HLG: Delivers High Dynamic Range effects with higher contrasts of
brightness and colors. This mode is only available when DISPLAY > HDR is set
at Auto, and HDR content is detected.
Sound Mode
Sound Mode function utilizes MaxxAudio sound enhancement technology, which
incorporates Waves’s algorithms to deliver great effects of the bass and treble and
provide you with immersive cinematic audio experience. The following preset
sound modes are provided: Standard, Cinema, Music, Game, Sport, and
User.
If the Mute function is activated, adjusting Sound Mode will turn off the Mute function.
Volume
Adjusts the sound level.
Mute
Temporarily turns off the sound.
Minimizing the response time (one frame) between the source input and the image
output, this mode will enhance the controlling experience.
Fast Mode
When using Fast Mode:
• In order to have minimized response time, Keystone, Overscan, and Digital Lens Shift
should be set at 0.
• Recommend timings are 1080P 60Hz/1080P 120Hz. See Timing chart on page 50 for
details.
Menu operation
29
This projector supports playing three-dimensional (3D) content transferred
through your 3D-compatible video devices and contents, such as PlayStation
consoles (with 3D game discs), 3D Blu-ray players (with 3D Blu-ray discs), 3D TV
(with 3D channel), and so on. After you have connected the 3D video devices to
the projector, wear the BenQ 3D glasses and make sure the power is on to view
3D contents.
When watching 3D contents,
• the image may seem misplaced, however, this is not a product malfunction.
• take appropriate breaks when watching 3D content.
• stop watching 3D content if you feel fatigue or discomfort.
3D Mode
• keep a distance from the screen of about three times the effective height of the screen when
watching 3D content.
• children and people with a history of oversensitivity to light, heart problems, or have any
other existing medical condition should be refrained from watching 3D content.
The default setting is Auto and the projector automatically chooses an
appropriate 3D format when detecting 3D contents. If the projector cannot
recognize the 3D format, manually choose a 3D mode according to your
preference.
When this function is enabled:
• The brightness level of the projected image decreases.
• The Picture Mode cannot be adjusted.
• The Vertical Keystone can only be adjusted within limited degrees.
The function is accessible through the remote control.
When your 3D image is distorted, enable this function to switch between the
3D Sync Invert image for the left eye and the right eye for comfortable 3D viewing experience.
The function is accessible through the remote control.
Press OK to enter its submenu.
Settings
Press BACK to save your changes and exit.
See below for more details.
30
Menu operation
Advanced menu
Picture
0
The projector is preset with several predefined picture modes so that you can
choose one to suit your operating environment and input signal picture type.
• Bright: Maximizes the brightness of the projected image. This mode is suitable
for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
• Living Room: Being slightly brighter than Cinema mode, it is suitable for playing
movies in rooms where there is a small amount of ambient light, eg. your living
room.
Picture Mode
• Cinema: With well-balanced color saturation and contrast with a low brightness
level, this is most suitable for enjoying movies in a totally dark environment (as you
would find in a commercial cinema).
• Sports: This mode is best for watching sporting events in rooms where is a small
amount of ambient light, et. your living room.
• Game: This mode is best for playing video games in rooms where there is a small
amount of ambient light, eg. your living room.
• User 1/User 2: Recalls the settings customized based on the current available
picture modes. See User Mode Management on page 32.
• 3D: Is appropriate for playing 3D images and 3D video clips.
• HDR10/HLG: Delivers High Dynamic Range effects with higher contrasts of
brightness and colors. This mode is only available when DISPLAY > HDR is set
at Auto, and HDR content is detected.
Menu operation
31
There are 2 user-definable modes if the current available picture modes are not
suitable for your need. You can use one of the picture modes (except the User
1/User 2) as a starting point and customize the settings.
1. Go to Picture > Picture Mode.
2. Press
/
to select User 1 or User 2.
3. Press
to highlight User Mode Management and press OK.
4. Highlight Load Settings From and press OK.
5. Press
to select a picture mode that is close to your need.
6. When done, press OK and BACK to return to the Picture menu.
User Mode
Management
7. Press to select other submenus you want to make changes and use
adjust the values. The adjustments define the selected user mode.
/
to
• Rename User Mode
Select to rename the customized picture modes (User 1 or User 2).
1. Go to the Picture > Picture Mode menu, select User 1 or User 2.
2. Press
to select User Mode Management.
3. On the User Mode Management window, select Rename User Mode and
press OK.
4. On the Rename User Mode window, use
characters for the selected mode.
/ / /
to select desired
5. When done, press OK and BACK to exit.
Brightness
The higher the value, the brighter the image. Adjust this control so the black areas
of the image appear just as black and that detail in the dark areas is visible.
Contrast
The higher the value, the greater the contrast. Use this to set the peak white level
after you have previously adjusted the Brightness setting to suit your selected input
and viewing environment.
Color
Lower setting produces less saturated colors. If the setting is too high, colors on
the image will be overpowering, which makes the image unrealistic.
Tint
The higher the value, the more greenish the picture becomes. The lower the value,
the more reddish the picture becomes.
Sharpness
The higher the value, the sharper the picture becomes.
32
Menu operation
Gamma Selection
Gamma refers to the relationship between input source and picture brightness.
• 1.6/1.8/2.0/2.1: Select these values according to your preference.
• 2.2/2.3: Increases the average brightness of the picture. Best for a lit environment, meeting
room or family room.
• 2.4: Best for viewing movies in a dark environment.
• 2.6/2.8/BenQ: Best for viewing movies which are mostly composed of dark scenes.
High Brightness
Low Contrast
1.6
Advanced
1.8
Low Brightness
High Contrast
2.0
2.1
2.2
2.3
2.4
2.6
2.8
BenQ
HDR Brightness
The projector can automatically adjust the brightness levels of your image according
to the input source. You can also manually select a brightness level to display better
picture quality. When the value is higher, the image becomes brighter; when the
value is lower, the image becomes darker.
Color Temperature
There are several preset color temperature settings available. The available settings
may vary according to the signal type selected.
• Lamp Native: With the lamp’s original color temperature and higher brightness. This setting
is suitable for environments where high brightness is required, such as projecting pictures in
well lit rooms.
• Warm: Makes images appear reddish white.
• Normal: Maintains normal colorings for white.
• Cool: Makes images appear bluish white.
Menu operation
33
Color Management
This function provides six sets (RGBCMY) of colors to be adjusted. When you
select each color, you can independently adjust its range and saturation according
to your preference.
• Primary Color: Selects a color from among R (Red), G (Green), B (Blue), C (Cyan), M
(Magenta), or Y (Yellow).
• Hue: Increase in the range will include colors consisted of
more proportions of its two adjacent colors. Please refer
to the illustration for how the colors relate to each other.
Yellow
RED
GREEN
For example, if you select Red and set its range at 0, only
pure red in the projected picture will be selected.
Increasing its range will include red close to yellow and red
close to magenta.
Cyan
Magenta
• Saturation: Adjusts the values to your preference. Every
BLUE
adjustment made will reflect to the image immediately. For
example, if you select Red and set its value at 0, only the
saturation of pure red will be affected.
Advanced
Saturation is the amount of that color in a video picture. Lower settings produce less saturated
colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that
color will be overpowering and unrealistic.
• Gain: Adjusts the values to your preference. The contrast level of the primary color you
select will be affected. Every adjustment made will reflect to the image immediately.
Noise Reduction
Reduces electrical image noise caused by different media players. The higher the
value, the less the noise.
Brilliant Color
This function utilizes a new color-processing algorithm and system level
enhancements to enable higher brightness while providing truer, more vibrant
colors in picture. It enables a greater than 50% brightness increase in mid-tone
images, which are common in video and natural scenes, so the projector
reproduces images in realistic and true colors.
Fast Mode
Minimizing the response time (one frame) between the source input and the image
output, this mode will enhance the controlling experience.
When using Fast Mode:
• In order to have minimized response time, Keystone, Overscan, and Digital Lens Shift
should be set at 0.
• Recommend timings are 1080P 60Hz/1080P 120Hz. See Timing chart on page 50 for details.
34
Menu operation
LumiExpert
• LumiExpert: When this function is enabled, the projector actively detects the
ambient light conditions and automatically adjusts balanced visual brightness to
create an optimum viewing experience.
This function is not available when the Picture Mode is Bright or 3D.
• LumiExpert Level: Adjusts the gamma offset.
• Manual Calibration: According to the ambient brightness, you can do the
calibration manually.
• Manual Calibration Status: Shows the status of manual calibration.
• Calibrate: Enact this item to start the calibration process.
• Reset Manual Calibration: Resets the gamma offset to factory preset
values.
Light Mode
Select the Light Mode. The options are Normal, Economic, SmartEco, and
LampSave.
Reset Current Returns all of the adjustments you’ve made for the Picture menu to the factory
Picture Mode preset values.
Sound
Sound Mode
Sound Mode function utilizes MaxxAudio sound enhancement technology, which
incorporates Waves’s algorithms to deliver great effects of the bass and treble and
provide you with immersive cinematic audio experience. The following preset
sound modes are provided: Standard, Cinema, Music, Game, Sport, and User.
If the Mute function is activated, adjusting Sound Mode will turn off the Mute function.
Mute
Temporarily turns off the sound.
Volume
Adjusts the sound level.
Power On/Off Sets the ring tone for the projector On or Off.
Ring Tone
Reset Audio
Settings
All of the adjustments you’ve done under the SOUND menu return to the factory
preset values.
Menu operation
35
Display
There are several options to set the image's aspect ratio depending on your input
signal source.
• Auto: Scales an image proportionally to fit the
projector's native resolution in its horizontal or
vertical width.
15:9 picture
• 4:3: Scales the picture so that it is displayed in the
center of the screen with a 4:3 aspect ratio.
Aspect Ratio
4:3 picture
• 16:9: Scales an image so that it is displayed in the
center of the screen with a 16:9 aspect ratio.
16:9 picture
• 16:10: Scales an image so that it is displayed in the
center of the screen with a 16:10 aspect ratio.
16:10 picture
Wall Color
Image
Position
Corrects the projected picture’s color when the projection surface such as a
painted wall which may not be white, the Wall Color feature can help correct the
projected picture’s colors to prevent possible color difference between the source
and projected pictures. There are several precalibrated colors to choose from:
Light Yellow, Pink, Light Green, and Blue.
Displays the Image Position window. You may use the directional arrow keys on
the projector or remote control to adjust the position of the projected picture.
The values shown on the lower position of the window change with every key press you made.
This function is only available when the PC signal is selected.
Conceals the poor picture quality in the four edges.
Overscan
Adjustment
The greater the value, the more portion of the picture is concealed while the
screen remains filled and geometrically accurate. Setting 0 means the picture is
100% displayed.
• Phase: Adjusts the clock phase to reduce image
distortion. This function is only available when a PC
signal (analog RGB) or YPbPr signal is selected.
PC &
Component
• H. Size: Adjusts the horizontal width of the image.
YPbPr Tuning This function is only available when a PC signal (analog RGB) is selected.
• Auto: Adjusts the phase and frequency automatically.
36
Menu operation
This projector features a 3D function which enables you to enjoy the 3D movies,
videos, and sporting events in a more realistic way by presenting the depth of the
images. You need to wear a pair of 3D glasses to view the 3D images.
• 3D Mode: The default setting is Off. If you want the projector to automatically
choose an appropriate 3D format when detecting 3D contents, select Auto. If the
projector cannot recognize the 3D format, press / to choose a 3D mode from
among Top Bottom, Frame Sequential, Frame Packing and Side by Side.
3D
When 3D function is activated:
• The brightness level of the projected image will decrease.
• The following settings cannot be adjusted: Picture Mode, Reference Mode.
• The Keystone can only be adjusted within limited degrees.
• 3D Sync Invert: When you discover the inversion of the image depth, enable
this function to correct the problem.
HDR
Digital Lens
Shift
The projector supports HDR imaging sources. It can automatically detect the
dynamic range of the source, and optimize settings to reproduce contents under
wide range of light conditions.
Use
/
to vertically shift the projected image.
System Setup : Basic
Language
Sets the language for the On-Screen Display (OSD) menus.
Background
Color
Sets the background color for the projector.
Splash Screen Allows you to select which logo screen will be displayed during projector start-up.
Projector
Position
See Choosing a location on page 11.
Auto Off
Allows the projector to turn off automatically if no input signal is detected after a
set period of time to prevent unnecessary waste of lamp life.
Direct Power
On
Allows the projector to turn on automatically once the power is fed through the
power cord.
• Menu Type: Switches to the Basic OSD menu.
• Menu Position: Sets the OSD menu position.
Menu Settings • Menu Display Time: Sets the length of time the OSD will remain active after
your last key press.
• Blank Reminder Message: Sets whether the reminder message is displayed by
the projector while the image is hidden.
Renames the current input source to your desired name.
Source
Rename
On the Source Rename window, use
the connected source item.
/ / /
to set the desired characters for
When done, press OK to save the changes.
Auto Source
Allows the projector to automatically search for a signal.
Menu operation
37
System Setup : Advanced
Light Settings
• Reset Light Timer: See Resetting the light timer on page 45.
• Light Usage Time: Displays the number of hours the light has been used.
• HDMI Range
Sets the HDMI Range to Auto, Full, or Limited.
HDMI
Settings
• HDMI EDID
Switch HDMI EDID between HDMI 1.4 or HDMI 2.0 in order to solve compatibility
issue with uncertain old players.
• Enhanced: Enhanced mode can switch to HDMI 2.0 EDID.
• Standard: Standard mode can switch to HDMI 1.4 EDID.
Baud Rate
Selects a baud rate that is identical with your computer’s so that you can connect
the projector using a suitable RS-232 cable and update or download the projector’s
firmware. This function is intended for qualified service personnel.
Adjusts the image size and focus and check that the
projected image is free from distortion.
Test Pattern
Quick Cooling
Select On enables the function and projector cooling time will be shortened from a
normal 90-second duration to approximately 15 seconds.
We recommend you use the High Altitude Mode when your environment is
between 1500 m –3000 m above sea level, and ambient temperature is between
0°C–30°C.
Operation under "High Altitude Mode" may cause a higher decibel operating
noise level because of increased fan speed necessary to improve overall system
cooling and performance.
High Altitude
Mode
If you use this projector under other extreme conditions excluding the above, it
may display auto shut-down symptoms, which is designed to protect your projector
from over-heating. In cases like this, you should switch to High Altitude mode to
solve these symptoms. However, this is not to state that this projector can operate
under any and all harsh or extreme conditions.
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient
temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on
under such a condition.
For security purposes and to prevent unauthorized use, you may set up password
security for the projector. See Utilizing the password function for details.
Password
• Change Password
You will be asked to enter the current password before changing to a new one.
• Power On Lock
Limits use of the projector to only those who know the correct password.
38
Menu operation
With the control keys on the projector locked, you can prevent your projector
settings from being changed accidentally (by children, for example).
Key Lock
When you select On to enable this function, no control keys on the projector will
function, except
POWER.
To unlock the keys, press and hold
on the projector for 3 seconds.
When you select On, all LED indicators on the projector function normally. See
Indicators for more details.
LED Indicator When you select Off, the LED indicators are off after you turn on the projector and
the splash screen displays. However, if the projector is not working properly, the
LED indicators light or flash to remind you that a problem may occur. See also
Indicators for more details.
Reset All
Settings
Returns all settings to the factory preset values.
The following settings will still remain: Picture, Keystone, Language, Projector Position,
Menu Type, Password, Key Lock, Reset Light Timer, and High Altitude Mode.
Information
• Source: Shows the current signal source.
• Picture Mode: Shows the selected mode in the Picture menu.
• Resolution: Displays the native resolution of the input source.
Information
• Color System: Shows input system format.
• Light Usage Time: Shows the number of hours the light has been used.
• 3D Format: Shows the current 3D mode.
• Firmware Version: Shows the firmware version of your projector.
• Service Code: Shows the service code of your projector.
Menu operation
39
Maintenance
Care of the projector
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. Please be sure to turn off the projector
and let it cool down completely before cleaning the lens.
• Use a canister of compressed air to remove dust.
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently
wipe the lens surface.
• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as
alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with
rubber or vinyl materials may result in damage to the projector surface and cabinet material.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as described in
Shutting down the projector on page 23 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH detergent. Then
wipe the case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
• Make sure the temperature and humidity of the storage area are within the recommended range for
the projector. Please refer to Specifications on page 48 or consult your dealer about the range.
• Retract the adjuster feet.
• Remove the battery from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
40
Maintenance
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by
the built-in timer. The method of calculating the equivalent lamp hour is as follows:
1. Light Usage Time = (x+y+z+a) hours, if:
Time used in Normal mode = x hours
Time used in Economic mode = y hours
Time used in SmartEco mode = z hours
Time used in LampSave mode = a hours
2. Equivalent Lamp Hour = α hours
A'
A'
A'
A'
α = ---- × χ + ---- × y + ---- × z + ---- × a
X
Y
Z
A
, if
X= lamp life spec of Normal mode
Y= lamp life spec of Economic mode
Z= lamp life spec of SmartEco mode
A= lamp life spec of LampSave mode
A’ is the longest lamp life spec among X, Y, Z, A
When you calculate Equivalent Light Usage hour manually, it will probably have deviation from the value shown in
OSD menu since projector system calculates time used for each light mode in “Minutes” then rounds down to an
integer in hours shown in OSD.
For time used in each light mode shown in OSD menu:
• Time used is accumulated and rounded down to an integer in hours.
• When time used is less than 1 hour, it shows 0 hours.
To obtain the lamp hour information:
1. Go to Advanced Menu - System Setup : Advanced > Light Settings and press OK. The
Light Settings page appears.
2. Press to select Light Usage Time and press OK. The Light Usage Time information is
displayed.
You can also get the Light Usage Time information on the Information menu.
Maintenance
41
Extending lamp life
• Setting the Light Mode
Go to Advanced Menu - Picture > Advanced > Light Mode, press OK. The Light Mode page
appears.
Setting the projector in Economic, SmartEco or LampSave mode extends lamp life.
Light Mode
Description
Normal
Economic
Provides full lamp brightness
Lowers brightness to extend the lamp life and decreases the fan noise
Adjusts the lamp power automatically depending on the content brightness level while
optimizing display quality
Adjusts the lamp power automatically depending on the content brightness level while
offering a longer lamp life
SmartEco
LampSave
• Setting Auto Power Off
This function allows the projector to turn off automatically if no input signal is detected after a set
period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go to Advanced Menu - System Setup : Basic > Auto Off and press
/ .
Timing of replacing the lamp
When the LIGHT indicator lights up or a message appears suggesting it is time to replace the lamp,
please consult your dealer or go to http://www.BenQ.com before installing a new lamp. An old lamp
may cause a malfunction in the projector and in some instances the light may explode.
• The apparent brightness of the projected image will vary depending on the ambient lighting conditions, selected
input signal contrast/brightness settings, and is directly proportional to projection distance.
• The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. This is
normal and expected behavior.
• The LIGHT indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn
the power off and let the projector cool for 45 minutes. If the Light or Temp indicator still lights up after
turning the power back on, please contact your dealer. See Indicators on page 46.
The following Lamp warning displays will remind you to change the lamp.
Order Replacement Lamp
Lamp>XXXX Hours
Order a new lamp at www.benq.com
Install a new lamp for optimal performance. Press OK to
dismiss the message.
OK
Replace Lamp Soon
Lamp>XXXX Hours
Order a new lamp at www.benq.com
OK
42
Maintenance
It is strongly recommended that you replace the lamp at this
age. The lamp is a consumable item. The lamp brightness
diminishes with use. This is normal lamp behavior. You can
replace the lamp whenever you notice that the brightness level
has significantly diminished.
Press OK to dismiss the message.
Replace Lamp Now
Lamp>XXXX Hours
Order a new lamp at www.benq.com
Lamp usage time exceeded
OK
Out of Lamp Usage Time
The lamp MUST be replaced before the projector will operate
normally.
Press OK to dismiss the message.
Replace lamp (Refer to user manual)
Then reset lamp timer
Order a new lamp at www.benq.com
OK
"XXXX" shown in the above messages are numbers that vary depending on different models.
Replacing the lamp (FOR SERVICE PERSONNEL ONLY)
• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before
changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp
glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the
empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper
manner.
• To assure optimal performance from the projector, it is recommended that you purchase a qualified projector
lamp for lamp replacement.
• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that
no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes caused by
fractured lamp.
• Ensure good ventilation when handling broken lamps. We recommend that you use respirators, safety glasses,
goggles or face shield and wear protective clothing such as gloves.
1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid
burns by waiting for approximately 45 minutes until the lamp has cooled.
2. Loosen the screw(s) that secure the lamp cover on the
side of the projector until the lamp cover loosens.
3. Remove the lamp cover from the projector.
• Do not turn the power on with the lamp cover open.
• Do not insert your fingers between the lamp and the
projector. The sharp edges inside the projector may
cause injuries
Maintenance
43
4. Disconnect the lamp connector.
5. Loosen the screw(s) that secure the inner lamp.
5
6
6. Lift the handle so that it stands up.
4
4
7. Use the handle to slowly pull the lamp out of the
projector.
• Pulling it too quickly may cause the lamp to break and scatter
broken glass in the projector.
• Do not place the lamp in locations where water might splash
on it, children can reach it, or near flammable materials.
• Do not insert your hands into the projector after the lamp is
removed. The sharp edges inside the projector may
cause injuries. If you touch the optical components
inside, it could cause color unevenness and distortion
of the projected images.
8. As shown in the figure, insert the new lamp. Align the
lamp connector and 2 sharp points with the projector
and push the lamp a bit into the locked position.
8
9. Insert the lamp connector.
9
8
10. Tighten the screw(s) that secures the lamp.
11. Ensure the handle is fully laid flat and locked in place.
• Loose screw may cause a bad connection, which could
result in malfunction.
• Do not over tighten the screw.
12. Replace the lamp cover on the projector.
13. Tighten the screw that secures the lamp cover.
• Loose screw may cause a bad connection, which could
result in malfunction.
• Do not over tighten the screw.
14. Connect the power and restart the projector.
44
Maintenance
10
11
Resetting the light timer
15. After the startup logo, open the On-Screen Display (OSD) menu. Go to Light Settings Menu System Setup : Advanced > Light Settings and press OK. The Light Settings page appears.
Highlight Reset Light Timer and press OK. A warning message is displayed asking if you want to
reset the lamp timer. Highlight Reset and press OK. The lamp time will be reset to “0”.
Do not reset if the lamp is not new or replaced as this could cause damage.
Maintenance
45
Indicators
Light
Status & Description
Power events
Stand-by mode
Powering up
Normal operation
Normal power-down cooling
Download
CW start fail
Light source life exhausted
Burn-In events
Burn-in ON
Burn-in OFF
Lamp events
Lamp error in normal operation
Lamp is not lit up
Thermal events
Fan 1 error (the actual fan speed is outside the desired speed)
Fan 2 error (the actual fan speed is outside the desired speed)
Fan 3 error (the actual fan speed is outside the desired speed)
Temperature 1 error (over limited temperature)
: Off
46
Maintenance
: Orange On
: Green On
: Red On
: Orange Flashing
: Green Flashing
: Red Flashing
Troubleshooting
The projector does not turn on.
Cause
There is no power from the power cord.
Remedy
Plug the power cord into the AC power jack on the
projector, and plug the power cord into the power outlet. If
the power outlet has a switch, make sure that it is switched
on.
Attempting to turn the projector on again during
Wait until the cooling down process has completed.
the cooling process.
No picture
Cause
Remedy
The video source is not turned on or connected
correctly.
The projector is not correctly connected to the
input signal device.
The input signal has not been correctly selected.
The lens cover is still closed.
Turn the video source on and check that the signal cable is
connected correctly.
Check the connection.
Select the correct input signal with the SOURCE key.
Open the lens cover.
Blurred image
Cause
The projection lens is not correctly focused.
The projector and the screen are not aligned
properly.
The lens cover is still closed.
Remedy
Adjust the focus of the lens using the focus ring.
Adjust the projection angle and direction as well as the
height of the projector if necessary.
Open the lens cover.
Remote control does not work.
Cause
Remedy
The batteries are out of power.
Replace both of the batteries with new ones.
There is an obstacle between the remote control
Remove the obstacle.
and the projector.
You are too far away from the projector.
Stand within 8 meters (26 feet) of the projector.
The password is incorrect.
Cause
You do not remember the password.
Remedy
See Entering the password recall procedure on page 22.
Troubleshooting
47
Specifications
Projector specifications
All specifications are subject to change without notice.
Optical
Input terminals
Resolution
1920 x 1080 FHD
Computer input
RGB input
D-Sub 15-pin (female) x 1
Display system
1-CHIP DMD
Lens
F = 1.94 ~ 2.07, f = 11.9 ~ 15.5 mm
Lamp
245 W lamp
Electrical
Power supply
AC100–240V, 3.8 A, 50–60 Hz (Automatic)
Power consumption
340 W (Max); < 0.5 W (Standby)
Mechanical
Weight
2.79 Kg (6.1 lbs)
Output terminals
RGB output
D-Sub 15-pin (female) x 1
Speaker
5 watt x 1
Audio signal output
PC audio jack x 1
Video signal input
SD/HDTV signal input
Analog - Component
(through RGB input)
Digital - HDMI 2.0 x 2
Audio signal input
Audio in
PC audio jack x 1
Environmental Requirements
Operating temperature
0°C–40°C at sea level
Operating relative humidity
10%–90% (without condensation)
Operating altitude
0–1499 m at 0°C–35°C
1500–3000 m at 0°C–30°C (with
High Altitude Mode on)
Storage temperature
-20°C–60°C at sea level
Storage humidity
10%–90% RH (without condensation)
Control
Storage altitude
30°C@ 0~12,200m above sea level
USB
Type-A power supply 5V / 2.5 A x 1
Transporting
Original packing or equivalent is recommended
RS-232 serial control
9 pin x 1
Repairing
Please visit below website and choose your country to
find your service contact window.
http://www.benq.com/welcome
IR receiver x 2
48
Specifications
Dimensions
312 mm (W) x 225 mm (D) x 110 mm (H)
312
225
110
Unit: mm
Specifications
49
Timing chart
Supported timing for PC input
Resolution
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1024 x 576
1024 x 600
1280 x 720
1280 x 768
1280 x 800
1280 x 1024
1280 x 960
1360 x 768
1400 x 1050
1440 x 900
1600 x 1200
1680 x 1050
640 x 480@67Hz
832 x 624@75Hz
1024 x 768@75Hz
1152 x 870@75Hz
1920 x 1080@60Hz
1920 x 1200@60Hz
Mode
VGA_60
VGA_72
VGA_75
VGA_85
VGA_120
720 x 400_70
SVGA_60
SVGA_72
SVGA_75
SVGA_85
SVGA_120
(Reduce Blanking)
XGA_60
XGA_70
XGA_75
XGA_85
XGA_120 (Reduce
Blanking)
1152 x 864_75
BenQ
Notebook_timing
BenQ
Notebook_timing
1280 x 720_60
1280 x 768_60
WXGA_60
WXGA_75
WXGA_85
WXGA_120
(Reduce Blanking)
SXGA_60
SXGA_75
SXGA_85
1280 x 960_60
1280 x 960_85
1360 x 768_60
SXGA+_60
WXGA+_60
UXGA
1680 x 1050_60
MAC13
MAC16
MAC19
MAC21
1920 x 1080_60
1920 x 1200_60
(Reduce Blanking)
Vertical
Frequency
(Hz)
Horizontal
Frequency
(kHz)
Pixel
Frequency
(MHz)
Supported 3D format
Frame
Top
Side-by-S
Sequential Bottom
ide
59.940
72.809
75.000
85.008
119.518
70.087
60.317
72.188
75.000
85.061
31.469
37.861
37.500
43.269
61.910
31.469
37.879
48.077
46.875
53.674
25.175
31.500
31.500
36.000
52.500
28.3221
40.000
50.000
49.500
56.250
119.854
77.425
83.000
V
60.004
70.069
75.029
84.997
48.363
56.476
60.023
68.667
65.000
75.000
78.750
94.500
V
119.989
97.551
115.5
V
75
67.5
108
60.0
35.820
46.966
64.995
41.467
51.419
60
59.87
59.810
74.934
84.880
45.000
47.776
49.702
62.795
71.554
74.250
79.5
83.500
106.500
122.500
V
V
V
119.909
101.563
146.25
V
60.020
75.025
85.024
60.000
85.002
60.015
59.978
59.887
60.000
59.954
66.667
74.546
74.93
75.060
60
63.981
79.976
91.146
60.000
85.938
47.712
65.317
55.935
75.000
65.290
35.000
49.722
60.241
68.680
67.5
108.000
135.000
157.500
108.000
148.500
85.5
121.750
106.500
162.000
146.250
30.240
57.280
80.000
100.000
148.5
59.95
74.038
154
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
The timings showing above may not be supported due to EDID file and VGA graphic card limitations. It is possible
that some timings cannot be chosen.
50
Specifications
Supported timing for HDMI (HDCP) input
• PC timings
Resolution
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1024 x 576@60Hz
1024 x 600@65Hz
1280 x 720
1280 x 768
1280 x 800
1280 x 1024
1280 x 960
1360 x 768
1440 x 900
1400 x 1050
1600 x 1200
1680 x 1050
640 x 480@67Hz
832 x 624@75Hz
1024 x 768@75Hz
1152 x 870@75Hz
1920 x 1080@60Hz
1920 x 1080@60Hz
(VESA)
1920 x 1080 @120Hz
1920 x 1200@60Hz
3840 x 2160
3840 x 2160
Mode
VGA_60
VGA_72
VGA_75
VGA_85
720 x 400_70
SVGA_60
SVGA_72
SVGA_75
SVGA_85
SVGA_120
(Reduce Blanking)
XGA_60
XGA_70
XGA_75
XGA_85
XGA_120 (Reduce
Blanking)
1152 x 864_75
BenQ Notebook
Timing
BenQ Notebook
Timing
1280 x 720_60
1280 x 768_60
WXGA_60
WXGA_75
WXGA_85
WXGA_120
(Reduce Blanking)
SXGA_60
SXGA_75
1280 x 960_60
1280 x 960_85
1360 x 768_60
WXGA+_60
SXGA+_60
UXGA
1680 x 1050_60
MAC13
MAC16
MAC19
MAC21
1920 x 1080_60
1920 x 1080_60
(For Auditorium
model)
1920 x 1080_60
(Only HDMI 2.0)
1920 x 1200_60
(Reduce Blanking)
3840 x 2160_30
(For 4K2K model)
3840 x 2160_60
(For 4K2K model)
(Only HDMI 2.0)
Vertical
Frequency
(Hz)
Horizontal
Pixel
Supported 3D format
Frequency Frequency
Frame
Top
Side-by-Si
(kHz)
(MHz)
Sequential Bottom
de
59.940
72.809
75.000
85.008
70.087
60.317
72.188
75.000
85.061
31.469
37.861
37.500
43.269
31.469
37.879
48.077
46.875
53.674
25.175
31.500
31.500
36.000
28.3221
40.000
50.000
49.500
56.250
V
V
V
V
V
V
119.854
77.425
83.000
V
60.004
70.069
75.029
84.997
48.363
56.476
60.023
68.667
65.000
75.000
78.750
94.500
V
V
V
119.989
97.551
115.5
V
75
67.5
108
60.00
35.820
46.996
64.995
41.467
51.419
60
59.870
59.810
74.934
84.880
45.000
47.776
49.702
62.795
71.554
74.250
79.5
83.500
106.500
122.500
V
V
V
V
V
V
V
V
V
119.909
101.563
146.25
V
60.020
75.025
60.000
85.002
60.015
59.887
59.978
60.000
59.954
66.667
74.546
75.020
75.06
60
63.981
79.976
60.000
85.938
47.712
55.935
65.317
75.000
65.290
35.000
49.722
60.241
68.68
67.5
108.000
135.000
108
148.500
85.500
106.500
121.750
162.000
146.250
30.240
57.280
80.000
100.00
148.5
V
V
V
V
V
V
V
V
V
V
V
V
V
V
59.963
67.158
173
120.000
135.000
297
59.95
74.038
154
V
V
30
67.5
297
60
135
594
V
The timings showing above may not be supported due to EDID file and VGA graphic card limitations. It is possible
that some timings cannot be chosen.
Specifications
51
Video timings
Timing
Resolution
Supported 3D format
Vertical Horizontal
Pixel
Frequency Frequency Frequency
Frame
Frame
Top
Side-by-Side
(Hz)
(kHz)
(MHz)
Sequential Packing Bottom
480i
720(1440) x 480
480p
720 x 480
576i
720(1440) x 576
576p
720 x 576
720/50p
1280 x 720
720/60p
1280 x 720
1080/50i
1920 x 1080
1080/60i
1920 x 1080
1080/24P
1920 x 1080
1080/25P
1920 x 1080
1080/30P
1920 x 1080
1080/50P
1920 x 1080
1080/60P
1920 x 1080
3840 x 2160
2160/24P
(Only HDMI 2.0)
3840 x 2160
2160/25P
(Only HDMI 2.0)
3840 x 2160
2160/30P
(Only HDMI 2.0)
3840 x 2160
2160/50P
(Only HDMI 2.0)
3840 x 2160
2160/60P
(Only HDMI 2.0)
59.94
59.94
50
50
50
60
50
60
24
25
30
50
60
15.73
31.47
15.63
31.25
37.5
45.00
28.13
33.75
27
28.13
33.75
56.25
67.5
27
27
27
27
74.25
74.25
74.25
74.25
74.25
74.25
74.25
148.5
148.5
54
24
297
56.25
25
297
67.5
30
297
112.5
50
594
135
60
594
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Supported timing for Component-YPbPr input
Timing
Resolution
480i
480p
576i
576p
720/50p
720/60p
1080/50i
1080/60i
1080/24P
1080/25P
1080/30P
1080/50P
1080/60P
720 x 480
720 x 480
720 x 576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
Vertical Frequency Horizontal Frequency Pixel Frequency
(Hz)
(kHz)
(MHz)
59.94
59.94
50
50
50
60
50
60
24
25
30
50
60
15.73
31.47
15.63
31.25
37.5
45.00
28.13
33.75
27
28.13
33.75
56.25
67.5
13.5
27
13.5
27
74.25
74.25
74.25
74.25
74.25
74.25
74.25
148.5
148.5
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration.
52
Specifications
Supported 3D
format
Frame
Sequential
V
V
V
RS232 command
RS232 pin assignment
No.
Serial
No.
Serial
1
2
3
4
5
NC
RX
TX
NC
GND
6
7
8
9
NC
RTSZ
CTSZ
NC
Function
Power
Source Selection
Audio Control
Picture Mode
Type
Write
Write
Read
Write
Write
Write
Read
Write
Write
Read
Write
Write
Write
Read
Write
Write
Write
Write
Write
Write
Write
Write
Read
Operation
Power On
Power off
Power Status
COMPUTER/YPbPr
HDMI(MHL)
HDMI 2
Current source
Mute On
Mute Off
Mute Status
Volume +
Volume Volume level for customer
Volume Status
Bright
Living Room
Game
Cinema
Football
User1
User2
3D
Picture Mode
1
2
6
3
7
4
8
5
9
ASCII
<CR>*pow=on#<CR>
<CR>*pow=off#<CR>
<CR>*pow=?#<CR>
<CR>*sour=RGB#<CR>
<CR>*sour=hdmi#<CR>
<CR>*sour=hdmi2#<CR>
<CR>*sour=?#<CR>
<CR>*mute=on#<CR>
<CR>*mute=off#<CR>
<CR>*mute=?#<CR>
<CR>*vol=+#<CR>
<CR>*vol=-#<CR>
<CR>*vol=value#<CR>
<CR>*vol=?#<CR>
<CR>*appmod=bright#<CR>
<CR>*appmod=livingroom#<CR>
<CR>*appmod=game#<CR>
<CR>*appmod=cine#<CR>
<CR>*appmod=football#<CR>
<CR>*appmod=user1#<CR>
<CR>*appmod=user2#<CR>
<CR>*appmod=threed#<CR>
<CR>*appmod=?#<CR>
Specifications
53
Function
Picture Setting
54
Specifications
Type
Write
Write
Write
Read
Write
Write
Write
Read
Write
Write
Write
Read
Write
Write
Write
Read
Write
Write
Write
Write
Read
Write
Write
Write
Write
Write
Write
Read
Write
Write
Read
Write
Write
Read
Operation
Contrast +
Contrast Set Contrast value
Contrast value
Brightness +
Brightness Set Brightness value
Brightness value
Color +
Color Set Color value
Color value
Sharpness +
Sharpness Set Sharpness value
Sharpness value
Color Temperature-Warm
Color Temperature-Normal
Color Temperature-Cool
Color Temperature-lamp native
Color Temperature Status
Aspect 4:3
Aspect 16:9
Aspect 16:10
Aspect Auto
Aspect Letterbox
Aspect Wide
Aspect Status
Vertical Keystone +
Vertical Keystone Vertical Keystone value
Overscan Adjustment +
Overscan Adjustment Overscan Adjustment value
ASCII
<CR>*con=+#<CR>
<CR>*con=-#<CR>
<CR>*con=value#<CR>
<CR>*con=?#<CR>
<CR>*bri=+#<CR>
<CR>*bri=-#<CR>
<CR>*bri=value#<CR>
<CR>*bri=?#<CR>
<CR>*color=+#<CR>
<CR>*color=-#<CR>
<CR>*color=value#<CR>
<CR>*color=?#<CR>
<CR>*sharp=+#<CR>
<CR>*sharp=-#<CR>
<CR>*sharp=value#<CR>
<CR>*sharp=?#<CR>
<CR>*ct=warm#<CR>
<CR>*ct=normal#<CR>
<CR>*ct=cool#<CR>
<CR>*ct=native#<CR>
<CR>*ct=?#<CR>
<CR>*asp=4:3#<CR>
<CR>*asp=16:9#<CR>
<CR>*asp=16:10#<CR>
<CR>*asp=AUTO#<CR>
<CR>*asp=LBOX#<CR>
<CR>*asp=WIDE#<CR>
<CR>*asp=?#<CR>
<CR>*vkeystone=+#<CR>
<CR>*vkeystone=-#<CR>
<CR>*vkeystone=?#<CR>
<CR>*overscan=+#<CR>
<CR>*overscan=-#<CR>
<CR>*overscan=?#<CR>
Function
Operation Settings
Baud Rate
Lamp Control
Type
Write
Write
Write
Read
Write
Write
Write
Write
Write
Read
Write
Write
Read
Write
Write
Read
Write
Write
Write
Write
Write
Read
Write
Write
Read
Write
Write
Write
Write
Write
Write
Read
Read
Write
Write
Write
Read
Operation
Auto
Brilliant color on
Brilliant color off
Brilliant color status
Reset picture settings
Projector Position-Front Table
Projector Position-Rear Table
Projector Position-Rear Ceiling
Projector Position-Front Ceiling
Projector Position Status
Quick cooling on
Quick cooling off
Quick cooling status
Quick auto search
Quick auto search
Quick auto search status
Menu Position - Center
Menu Position - Top-Left
Menu Position - Top-Right
Menu Position - Bottom-Right
Menu Position - Bottom-Left
Menu Position Status
Direct Power On-on
Direct Power On-off
Direct Power On-Status
9600
14400
19200
38400
57600
115200
Current Baud Rate
Lamp
Normal mode
Eco mode
SmartEco mode
Lamp Mode Status
ASCII
<CR>*auto#<CR>
<CR>*BC=on#<CR>
<CR>*BC=off#<CR>
<CR>*BC=?#<CR>
<CR>*rstpicsetting#<CR>
<CR>*pp=FT#<CR>
<CR>*pp=RE#<CR>
<CR>*pp=RC#<CR>
<CR>*pp=FC#<CR>
<CR>*pp=?#<CR>
<CR>*qcool=on#<CR>
<CR>*qcool=off#<CR>
<CR>*qcool=?#<CR>
<CR>*QAS=on#<CR>
<CR>*QAS=off#<CR>
<CR>*QAS=?#<CR>
<CR>*menuposition=center#<CR>
<CR>*menuposition=tl#<CR>
<CR>*menuposition=tr#<CR>
<CR>*menuposition=br#<CR>
<CR>*menuposition=bl#<CR>
<CR>*menuposition=?#<CR>
<CR>*directpower=on#<CR>
<CR>*directpower=off#<CR>
<CR>*directpower=?#<CR>
<CR>*baud=9600#<CR>
<CR>*baud=14400#<CR>
<CR>*baud=19200#<CR>
<CR>*baud=38400#<CR>
<CR>*baud=57600#<CR>
<CR>*baud=115200#<CR>
<CR>*baud=?#<CR>
<CR>*ltim=?#<CR>
<CR>*lampm=lnor#<CR>
<CR>*lampm=eco#<CR>
<CR>*lampm=seco#<CR>
<CR>*lampm=?#<CR>
Specifications
55
Function
Miscellaneous
56
Specifications
Type
Read
Read
Read
Read
Read
Write
Write
Read
Write
Write
Read
Write
Write
Write
Write
Write
Write
Write
Write
Read
Write
Write
Write
Write
Write
Write
Write
Write
Read
Operation
Model Name
System F/W Version
Scaler F/W Version
MCU F/W Version
Ballast F/W Version
Blank On
Blank Off
Blank Status
Menu On
Menu Off
Menu Status
Up
Down
Right
Left
Enter
Back
Source Menu On
Source Menu Off
Source Menu Status
3D Sync Off
3D Auto
3D Sync Top Bottom
3D Sync Frame Sequential
3D Frame packing
3D Side by side
3D inverter disable
3D inverter
3D Sync Status
ASCII
<CR>*modelname=?#<CR>
<CR>*sysfwversion=?#<CR>
<CR>*scalerfwversion=?#<CR>
<CR>*mcufwversion=?#<CR>
<CR>*ballastfwversion=?#<CR>
<CR>*blank=on#<CR>
<CR>*blank=off#<CR>
<CR>*blank=?#<CR>
<CR>*menu=on#<CR>
<CR>*menu=off#<CR>
<CR>*menu=?#<CR>
<CR>*up#<CR>
<CR>*down#<CR>
<CR>*right#<CR>
<CR>*left#<CR>
<CR>*enter#<CR>
<CR>*back#<CR>
<CR>*sourmenu=on#<CR>
<CR>*sourmenu=off#<CR>
<CR>*sourmenu=?#<CR>
<CR>*3d=off#<CR>
<CR>*3d=auto#<CR>
<CR>*3d=tb#<CR>
<CR>*3d=fs#<CR>
<CR>*3d=fp#<CR>
<CR>*3d=sbs#<CR>
<CR>*3d=da#<CR>
<CR>*3d=iv#<CR>
<CR>*3d=?#<CR>

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement