advertisement
▼
Scroll to page 2
of 3
ASTER ISION MODULAR SWITCHBOARDS HOW TO ASSEMBLE A MASTERVISION PANEL connector bar 07-09-07810 1. For best results, use Mastervision installation parts 2. Use connector bar 07-09-07810 and connector block 07-09-07820 to assemble the panel. 3. The mounting bolts used are M4x25 4. Secure the bolts wit hte supplied M4 nuts and O-rings. 5. To fasten the electrical panel in its frame or bulkhead use the the stencil as supplied to cut the panelhole. 6. connector block 07-09-07820 Do not use connector blocks at the outside top or bottom edge. This is where the complete panel will be fastened to its frame or bulkhead. 10/30V DC power supply for backlight HOW TO INSTALL THE BACKLIGHTING SYSTEM: Indicator wire to load side of breaker The Mastervision panels have a two-state backlight system for label illumination. The first state is a low intensity green light that illuminates the labels on the panel to enable label viewing in low light conditions, any time the circuit is switched ON or OFF. The second state is a higher intensity yellow DC LED (or orange neon lamp for AC) to indicate when a circuit is switched ON. Power must be fed to all modules with backlight capability. This is achieved by linking all the modules together by their backlight connectors (see drawing). Verify the backlight AC or DC voltage on each module. Note: The power supply voltages are equal on all backlight modules, indicator voltages are depending on the type of panel. backlight 5 DC busbar for 5 breakers HOW TO LABEL A BACKLIGHT DC MODULE To place the labels on the backlight module remove the mounting bolts and turn the module around. Place the label in the embossed square on the lens. Make sure that the label is placed correctly and the indicator led is uncovered. Replace the backlight module in the original position. connect the indicator wire to the load side of the breaker 10/30V power supply Warning: When the module is placed correctly the indicator led is 1mm away from the transparant front lens. 1mm AC MODULE NAVIGATION INSTRUMENTS L phase N neutral 1mm 10/30V power supply CAUTION GENERAL 1. Lethal voltages exist on your vessel. Make sure all shore power, onboard generating sources and batteries are disconnected before beginning installation of your electrical panel. 2. AC modules will have lethal voltages on the bus bars and terminals. Additional safety enclosures as the AC protection shield (part no. 07-09-04601-2-3) may be required in some installations. 3. Make sure all Ac modules are bonded tot the ship’s AC ground bus. When grouping modules together to form your panel, a single ground may be used. Use an ohm meter to verify ground to all modules. 1. Verify the modules you purchased arev configured for the source voltage aboard your vessel / mobile. Refer to the backlight specification. 2. Installation of Mastervision panels should be completed by a person with a thorough knowledge of marine / mobile electrical systems. 3. Wiring to and from each module should be conform to the local applicable standards and taking into consideration the safety guidelines and measures. Mastervolt can accept no liability for damage due to the use of the panel or due to possible errors in the manual and the results thereof. backlight module 5 labels 12/24V DC backlight module 2 labels 12/24V DC backlight module 5 labels 230V AC backlight module 2 labels 230V AC LED 12/24V 3mm flathead yellow (prewired) 10 each LED 12/24V 3mm flathead green (prewired) 10 each LED 12/24V 3mm flathead red (prewired) 10 each LED 12/24V 3mm flathead (4 x yellow/ 4 x green/ 2 x red) neon lamp 230V 6mm orange (prewired) 10 each circuit breaker type rocker CD 1 pole max 100A red circuit breaker type rocker CD 2 pole max 100A red circuit breaker type rocker CD 1 pole max 190A red (B-3-BS) circuit breaker type rocker MD 1 pole max 25A red panel hole plug A series rocker panel hole plug M series rocker 07-09-052xx 07-09-053xx 07-09-05301 07-09-052xx 07-09-05600 07-09-05610 = breaker current value circuit breaker type rocker AD 1 pole max 50A red with fingerguard circuit breaker type rocker AD 1 pole max 50A red push to reset 07-09-05091 07-09-05093 xx circuit breaker type rocker AD 1 pole max 50A red circuit breaker type rocker AD 2 pole max 50A red 07-09-050xx 07-09-051xx CIRQUIT BREAKERS CARLINGSWITCH 07-09-04310 07-09-04312 07-09-04320 07-09-04322 07-09-04400 07-09-04402 07-09-04404 07-09-04406 07-09-04500 BACKLIGHT MODULES INSTALLATION ACCESSORIES rockerswitch on-off 8A black rockerswitch on-off-on 8A black 07-09-04601 07-09-04602 07-09-04603 Mastervolt/22-04-00 [email protected] labelsheet 1 with 143 labels englisch labelsheet 2 with 143 labels dutch labelsheet 3 with 143 labels french labelsheet 4 with 143 labels german AC protectionshield for panel 1 AC protectionshield for panel 2 AC protectionshield for panel 3 mass charger panel lights main breaker outlets AC 220 V terminal screws - hex. 10/32 -for breakers AD series (10 each) terminal screws - hex. 8/32 - for breakers MD series (10 each) connector bar 145x20mm to connect 3 panels connector block 25x20mm to connect 2 panels bus bar to connect 2 breakers bus bar to connect 5 breakers AC PROTECTION SETS 07-09-07910 07-09-07920 07-09-07930 07-09-07940 LABELSHEETS 07-09-05700 07-09-05710 07-09-07810 07-09-07820 07-09-07840 07-09-07830 INSTALLATION COMPONENTS 07-09-07610 07-09-07620 PANEL SWITCHES MASTERVOLT SNIJDERSBERGWEG 93 , 1105 AN AMSTERDAM THE NETHERLANDS WWW.MASTERVOLT.COM ASTER ISION MODULAR SWITCHBOARDS 130 6 Serie 1 240x130mm Serie 2 120x130mm Serie 3 120x65mm Serie 4 60x65mm copy this paper and assemble the panel on paper tape the paper-panel on the background drill the mounting holes cut the panel hole maximum panel depth 120 mm 1. 2. 3. 4. NOTE: To dimension the panel cut out, follow these steps: drill 5mm 240 228 1 0,75 0,75 0,75 0,75 0,75 0,75 0,75 1,5 1,5 1,5 Amp 1 2 3 4 5 6 7 8 9 10 0,75 0,75 0,75 0,75 0,75 0,75 1,5 1,5 1,5 1,5 2 0,75 0,75 0,75 0,75 0,75 1,5 1,5 1,5 1,5 2,5 3 0,75 0,75 0,75 0,75 1,0 1,5 1,5 2,5 2,5 4 4 108 120 0,75 0,75 0,75 1,0 1,5 1,5 2,5 2,5 4 4 5 0,75 0,75 0,75 1,5 1,5 2,5 2,5 4 4 4 6 length in meters 65 0,75 0,75 1 1,5 2,5 2,5 4 4 4 6 7 0,75 1 1,5 2,5 2,5 4 4 4 6 6 8 0,75 1 1,5 2,5 4 4 4 6 6 6 9 0,75 1,5 2,5 4 4 4 6 6 6 6 10 48 1 1,5 2,5 4 4 6 6 6 10 10 15 1,5 1,5 4 4 6 6 10 10 10 10 20 6 Mastervolt/ 22-04-00 53 PANEL CUT OUT SIZING (dimensions in mm) ASTER ISION MODULAR SWITCHBOARDS 118
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project