RIVA RC4602SV Quick Installation Guide

Quick Installation Guide
This manual provides the instructions for the quick installation and the basic configuration of your camera with
the 30x optical zoom.
!
Please install the device after removing the bubble wrap inside the dome cover.
Caution
1. Connect cables to IP device
Connect the required cables to the device including a power cable and a LAN cable. To see the correct
positions of all the connectors, refer to the image below.
< PCB Top View >
LAN connector
6-pin
terminal
block
(Digital Output)
8-pin
terminal
block
(Digital Input)
Audio microphone
stereo jack connector
Audio speaker
stereo jack connector
3-pin terminal block connector
32-pin socket
microSD / SDHC slot
< Top View of Camera’s Main Body>
* Model design and appearance are subject to change without any prior notice.
!
Incorrect connection may cause malfunction or damage to your IP device.
Caution
RC4602SV01-2017-A
1
2. Install IP device
1) Loosen the three screws on the
top of the camera, and detach the
safety ring from the top.
2) Twist the top of the camera
counter-clockwise to separate it from
the main body, and push the lever of
the plastic cover at the bottom of the
top outward to open it. Then, insert
the provided terminal block to the
corresponding places on the PCB.
3) Drop all the necessary cables
through the neck of the camera’s top,
and fix the top to your installed
bracket or on the designated spot.
4) Install the provided ferrite cores on
the cables by winding cables around
the ferrite cores once. Refer to the
image on the left.
5) Connect all the cables to the
corresponding connectors by referring to
the image on the previous page. Then,
close the PCB on the top of the camera.
Audio cable
power cable
DI/DO cable
6) Hook the safety ring to the top of
the camera while carefully holding the
camera's main body, and align the
triangle marks on the top with the
main body.
LAN cable
7) Twist the main body counterclockwise once the camera’s top and
the main body are properly aligned,
and tighten the three screws on the
top.
i
The internal heater does not work when the device is powered via PoE.
Note
To prevent products from damage, place the camera on stable and non-vibrating
surfaces. If the stability is in doubt, consult safety personnel for reinforcements, and then
Caution proceed with the installation.
!
RC4602SV01-2017-A
2
3. Set the lens position
The device is a 360° rotating camera and it is fully controlled by the web user interface. Once the
installation is complete and it is properly connected to the network, please refer to the webpage user’s
manual for the camera configuration instructions.
Also, the camera is equipped with the 30x optical zoom lens with the auto focus feature, and the zoom
and focus are also fully controlled by the web user interface. Refer to the webpage user’s manual for the
zoom/focus configuration instructions.
4. Set up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of the device from
converting the MAC address’s hexadecimal numbers, which is attached to the device. Be sure that the
device and PC are on a same area network before running the installation.
Generic IP Environment
In case of generic private network environment where IP address 192.168.XXX.XXX are used, users may
view the live streaming images on a web page using the device’s default IP address:
1.
Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal Conversion
Chart at the end of the manual.
(The MAC address of the device is attached on the side or bottom of the device.)
MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177
Convert the last two sets of hexadecimal numbers to decimal numbers.
2.
Start the Microsoft® Internet Explorer web browser and enter the IP address of the device.
3.
Web streaming and device configurations are supported through ActiveX program. When the ActiveX
installation pop-up window appears, authorize and install the ActiveX setup.exe,
RC4602SV01-2017-A
3
Custom IP Environment
Please access our website and download necessary IPAdminTool first:
http://www.rivatech.de/en/downloads/software
IPAdminTool is a management tool, which automatically scans all of the network products for users to
perform administrative tasks, which includes network configurations, firmware update, device reboot, and
device organizations.
To modify the device’s default IP address for customized network area;
1. Find the device from the IPAdminTool’s list, and highlight the device’s name.
2. Right-click the mouse and select IP Address; IP Setup window appears.
* There are two options that are for a single device or for multiple devices respectively. For one device, click “Single”.
Give a new unique IP address by
modifying the last two digits.
3. On the New Information table in the Single IP Change window, modify the last two digits of the device’s
IP address, , and modify the rest parts including subnet mask, gateway, and DNS if necessary by
checking the user’s PC network area information.
4. Input the correct ID and PW of the device (default: root / pass).
5. Click Apply to complete the modification.
RC4602SV01-2017-A
4
5. View video on web page
Installation of ActiveX control
Once the device’s proper IP address has been identified, type the URL in a web browser to access the
camera. At first time access, installation window may pop up.
1.
When the browser asks to install the AxUMF software, click Install to proceed.
2.
When the setup installation pop-up window appears, click Install to proceed with rest of installations.
i
Note
Depending on system OS and Internet Explorer version, installation experience may
differ from one another. Figures described above are from Windows 7, Internet
Explorer 9 environment.
Login to webpage
To set up the Network configuration:
1.
2.
Click Setup on the upper right of the web page. The login page is displayed as below.
Enter the default user name (root) and password (pass), and then select OK.
The default username
and password are:
root and pass.
RC4602SV01-2017-A
5
6. Reboot
Perform the following procedures to reset your device:
On the Device
1.
2.
Press the reset button for 2 seconds while the device is powered on.
Wait for the system to reboot.
Reset Button
!
Caution
Please do not hold the reset button for more than 2 seconds. Otherwise, the camera
may be switched to its factory default settings.
On the Camera’s Webpage
1.
2.
Go to Setup > Maintenance > Reboot.
Click Reboot to reboot the device.
7. Factory Default
Resetting the device back to the factory default will initialize all parameters including the IP address back to
the factory defaults. To reset back to the factory default:
On the Device
1. Press the reset button and hold it while the device is powered on.
2. Release the button after 10 seconds.
3. Wait for the system to reboot.
On the Camera’s Webpage
1.
2.
3.
Go to Setup > Maintenance > Reset All Settings.
Select the items that you want to keep from the initialization among network settings, user account
information, and time zone setting.
Click Reset All Settings.
The factory default settings can be inferred as follows:
i
Note
IP address: 192.168.xx.yy
Network mask: 255.255.0.0
Gateway: 192.168.0.1
User ID: root
Password: pass
RC4602SV01-2017-A
6
8. Safe Mode
Your device will get restarted in safe mode if the device does not completely boot certain times.
The errors are mainly caused by these factors below:
* The power supply is continually unplugged certain times in the middle of system booting.
* The firmware files required for system booting are damaged.
* There are conflicts in the system settings.
You will see the page to indicate that your device is in safe mode and to guide you what to do step by
step.
Follow the instructions on the webpage according to each step.
i
Note
i
Note
There is another method to update firmware, which is using IPAdminTool.
Please refer to ‘IPAdminTool User’s Manual.pdf’ for the detailed procedure.
If your device is still in safe mode after trying to update firmware, please contact your
local agency to get further assistance.
RC4602SV01-2017-A
7
Hexadecimal-Decimal Conversion Table
Refer to the following table when you convert the MAC address of your device to IP address.
Hex Dec
Hex Dec
Hex Dec
Hex Dec
Hex Dec
Hex Dec
Hex Dec
0
0
25
37
4A
74
6F
111
94
148
B9
185
DE
222
1
1
26
38
4B
75
70
112
95
149
BA
186
DF
223
2
2
27
39
4C
76
71
113
96
150
BB
187
E0
224
3
3
28
40
4D
77
72
114
97
151
BC
188
E1
225
4
4
29
41
4E
78
73
115
98
152
BD
189
E2
226
5
5
2A
42
4F
79
74
116
99
153
BE
190
E3
227
6
6
2B
43
50
80
75
117
9A
154
BF
191
E4
228
7
7
2C
44
51
81
76
118
9B
155
C0
192
E5
229
8
8
2D
45
52
82
77
119
9C
156
C1
193
E6
230
9
9
2E
46
53
83
78
120
9D
157
C2
194
E7
231
0A
10
2F
47
54
84
79
121
9E
158
C3
195
E8
232
0B
11
30
48
55
85
7A
122
9F
159
C4
196
E9
233
0C
12
31
49
56
86
7B
123
A0
160
C5
197
EA
234
0D
13
32
50
57
87
7C
124
A1
161
C6
198
EB
235
0E
14
33
51
58
88
7D
125
A2
162
C7
199
EC
236
0F
15
34
52
59
89
7E
126
A3
163
C8
200
ED
237
10
16
35
53
5A
90
7F
127
A4
164
C9
201
EE
238
11
17
36
54
5B
91
80
128
A5
165
CA
202
EF
239
12
18
37
55
5C
92
81
129
A6
166
CB
203
F0
240
13
19
38
56
5D
93
82
130
A7
167
CC
204
F1
241
14
20
39
57
5E
94
83
131
A8
168
CD
205
F2
242
15
21
3A
58
5F
95
84
132
A9
169
CE
206
F3
243
16
22
3B
59
60
96
85
133
AA
170
CF
207
F4
244
17
23
3C
60
61
97
86
134
AB
171
D0
208
F5
245
18
24
3D
61
62
98
87
135
AC
172
D1
209
F6
246
19
25
3E
62
63
99
88
136
AD
173
D2
210
F7
247
1A
26
3F
63
64
100
89
137
AE
174
D3
211
F8
248
1B
27
40
64
65
101
8A
138
AF
175
D4
212
F9
249
1C
28
41
65
66
102
8B
139
B0
176
D5
213
FA
250
1D
29
42
66
67
103
8C
140
B1
177
D6
214
FB
251
1E
30
43
67
68
104
8D
141
B2
178
D7
215
FC
252
1F
31
44
68
69
105
8E
142
B3
179
D8
216
FD
253
20
32
45
69
6A
106
8F
143
B4
180
D9
217
FE
254
21
33
46
70
6B
107
90
144
B5
181
DA
218
FF
255
22
34
47
71
6C
108
91
145
B6
182
DB
219
23
35
48
72
6D
109
92
146
B7
183
DC
220
24
36
49
73
6E
110
93
147
B8
184
DD
221
RC4602SV01-2017-A
8